[PATCH] ARM: 2745/1: Fix IXP4xx debug macros
Patch from Deepak Saxena
Current IXP4xx debug macros do not work in the small window between
the MMU being enabled and the call to map_io() b/c the standard
peripheral mapping is not properly setup for use with the low-level
debug code. This patch creates a new section-aligned mapping for the
UART specifically for use with the debug macros.
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-ixp4xx/common.c b/arch/arm/mach-ixp4xx/common.c
index 267ba02..f39e8408 100644
--- a/arch/arm/mach-ixp4xx/common.c
+++ b/arch/arm/mach-ixp4xx/common.c
@@ -141,7 +141,15 @@
.physical = IXP4XX_PCI_CFG_BASE_PHYS,
.length = IXP4XX_PCI_CFG_REGION_SIZE,
.type = MT_DEVICE
+ },
+#ifdef CONFIG_DEBUG_LL
+ { /* Debug UART mapping */
+ .virtual = IXP4XX_DEBUG_UART_BASE_VIRT,
+ .physical = IXP4XX_DEBUG_UART_BASE_PHYS,
+ .length = IXP4XX_DEBUG_UART_REGION_SIZE,
+ .type = MT_DEVICE
}
+#endif
};
void __init ixp4xx_map_io(void)
diff --git a/include/asm-arm/arch-ixp4xx/debug-macro.S b/include/asm-arm/arch-ixp4xx/debug-macro.S
index 4499ae8..45a6c6c 100644
--- a/include/asm-arm/arch-ixp4xx/debug-macro.S
+++ b/include/asm-arm/arch-ixp4xx/debug-macro.S
@@ -14,6 +14,7 @@
mrc p15, 0, \rx, c1, c0
tst \rx, #1 @ MMU enabled?
moveq \rx, #0xc8000000
+ orrne \rx, \rx, #0x00b00000
movne \rx, #0xff000000
add \rx,\rx,#3 @ Uart regs are at off set of 3 if
@ byte writes used - Big Endian.
diff --git a/include/asm-arm/arch-ixp4xx/ixp4xx-regs.h b/include/asm-arm/arch-ixp4xx/ixp4xx-regs.h
index 8eeb1db..004696a 100644
--- a/include/asm-arm/arch-ixp4xx/ixp4xx-regs.h
+++ b/include/asm-arm/arch-ixp4xx/ixp4xx-regs.h
@@ -69,6 +69,16 @@
#define IXP4XX_PERIPHERAL_BASE_VIRT (0xFFBF2000)
#define IXP4XX_PERIPHERAL_REGION_SIZE (0x0000C000)
+/*
+ * Debug UART
+ *
+ * This is basically a remap of UART1 into a region that is section
+ * aligned so that it * can be used with the low-level debug code.
+ */
+#define IXP4XX_DEBUG_UART_BASE_PHYS (0xC8000000)
+#define IXP4XX_DEBUG_UART_BASE_VIRT (0xffb00000)
+#define IXP4XX_DEBUG_UART_REGION_SIZE (0x00001000)
+
#define IXP4XX_EXP_CS0_OFFSET 0x00
#define IXP4XX_EXP_CS1_OFFSET 0x04
#define IXP4XX_EXP_CS2_OFFSET 0x08