USB: add urb->ep
This patch (as943) prepares the way for eliminating urb->pipe by
introducing an endpoint pointer into struct urb. For now urb->ep
is set by usb_submit_urb() from the pipe value; eventually drivers
will set it themselves and we will remove urb->pipe completely.
The patch also adds new inline routines to retrieve an endpoint
descriptor's number and transfer type, essentially as replacements for
usb_pipeendpoint and usb_pipetype.
usb_submit_urb(), usb_hcd_submit_urb(), and usb_hcd_unlink_urb() are
converted to use the new field and new routines. Other parts of
usbcore will be converted in later patches.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/usb/core/urb.c b/drivers/usb/core/urb.c
index be63022..ff53acb 100644
--- a/drivers/usb/core/urb.c
+++ b/drivers/usb/core/urb.c
@@ -277,9 +277,10 @@
*/
int usb_submit_urb(struct urb *urb, gfp_t mem_flags)
{
- int pipe, temp, max;
- struct usb_device *dev;
- int is_out;
+ int xfertype, max;
+ struct usb_device *dev;
+ struct usb_host_endpoint *ep;
+ int is_out;
if (!urb || urb->hcpriv || !urb->complete)
return -EINVAL;
@@ -291,30 +292,34 @@
|| dev->state == USB_STATE_SUSPENDED)
return -EHOSTUNREACH;
+ /* For now, get the endpoint from the pipe. Eventually drivers
+ * will be required to set urb->ep directly and we will eliminate
+ * urb->pipe.
+ */
+ ep = (usb_pipein(urb->pipe) ? dev->ep_in : dev->ep_out)
+ [usb_pipeendpoint(urb->pipe)];
+ if (!ep)
+ return -ENOENT;
+
+ urb->ep = ep;
urb->status = -EINPROGRESS;
urb->actual_length = 0;
/* Lots of sanity checks, so HCDs can rely on clean data
* and don't need to duplicate tests
*/
- pipe = urb->pipe;
- temp = usb_pipetype(pipe);
- is_out = usb_pipeout(pipe);
+ xfertype = usb_endpoint_type(&ep->desc);
+ is_out = usb_pipeout(urb->pipe);
- if (!usb_pipecontrol(pipe) && dev->state < USB_STATE_CONFIGURED)
+ if (xfertype != USB_ENDPOINT_XFER_CONTROL &&
+ dev->state < USB_STATE_CONFIGURED)
return -ENODEV;
- /* FIXME there should be a sharable lock protecting us against
- * config/altsetting changes and disconnects, kicking in here.
- * (here == before maxpacket, and eventually endpoint type,
- * checks get made.)
- */
-
- max = usb_maxpacket(dev, pipe, is_out);
+ max = le16_to_cpu(ep->desc.wMaxPacketSize);
if (max <= 0) {
dev_dbg(&dev->dev,
"bogus endpoint ep%d%s in %s (bad maxpacket %d)\n",
- usb_pipeendpoint(pipe), is_out ? "out" : "in",
+ usb_endpoint_num(&ep->desc), is_out ? "out" : "in",
__FUNCTION__, max);
return -EMSGSIZE;
}
@@ -323,7 +328,7 @@
* but drivers only control those sizes for ISO.
* while we're checking, initialize return status.
*/
- if (temp == PIPE_ISOCHRONOUS) {
+ if (xfertype == USB_ENDPOINT_XFER_ISOC) {
int n, len;
/* "high bandwidth" mode, 1-3 packets/uframe? */
@@ -359,19 +364,19 @@
/* enforce simple/standard policy */
allowed = (URB_NO_TRANSFER_DMA_MAP | URB_NO_SETUP_DMA_MAP |
URB_NO_INTERRUPT);
- switch (temp) {
- case PIPE_BULK:
+ switch (xfertype) {
+ case USB_ENDPOINT_XFER_BULK:
if (is_out)
allowed |= URB_ZERO_PACKET;
/* FALLTHROUGH */
- case PIPE_CONTROL:
+ case USB_ENDPOINT_XFER_CONTROL:
allowed |= URB_NO_FSBR; /* only affects UHCI */
/* FALLTHROUGH */
default: /* all non-iso endpoints */
if (!is_out)
allowed |= URB_SHORT_NOT_OK;
break;
- case PIPE_ISOCHRONOUS:
+ case USB_ENDPOINT_XFER_ISOC:
allowed |= URB_ISO_ASAP;
break;
}
@@ -393,9 +398,9 @@
* supports different values... this uses EHCI/UHCI defaults (and
* EHCI can use smaller non-default values).
*/
- switch (temp) {
- case PIPE_ISOCHRONOUS:
- case PIPE_INTERRUPT:
+ switch (xfertype) {
+ case USB_ENDPOINT_XFER_ISOC:
+ case USB_ENDPOINT_XFER_INT:
/* too small? */
if (urb->interval <= 0)
return -EINVAL;
@@ -405,29 +410,29 @@
// NOTE usb handles 2^15
if (urb->interval > (1024 * 8))
urb->interval = 1024 * 8;
- temp = 1024 * 8;
+ max = 1024 * 8;
break;
case USB_SPEED_FULL: /* units are frames/msec */
case USB_SPEED_LOW:
- if (temp == PIPE_INTERRUPT) {
+ if (xfertype == USB_ENDPOINT_XFER_INT) {
if (urb->interval > 255)
return -EINVAL;
// NOTE ohci only handles up to 32
- temp = 128;
+ max = 128;
} else {
if (urb->interval > 1024)
urb->interval = 1024;
// NOTE usb and ohci handle up to 2^15
- temp = 1024;
+ max = 1024;
}
break;
default:
return -EINVAL;
}
/* power of two? */
- while (temp > urb->interval)
- temp >>= 1;
- urb->interval = temp;
+ while (max > urb->interval)
+ max >>= 1;
+ urb->interval = max;
}
return usb_hcd_submit_urb(urb, mem_flags);