[ARM] pxa/spitz: convert to use new MFP API
Original patch from Dmitry Baryshkov's initial scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.
TODO: figure out the MFP configuration of the SSP2 which looks like
to be already configured by the boot loader, though.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index fef5018..1a53c2c 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -38,7 +38,7 @@
#include <mach/pxa-regs.h>
#include <mach/pxa2xx-regs.h>
-#include <mach/pxa2xx-gpio.h>
+#include <mach/mfp-pxa27x.h>
#include <mach/pxa27x-udc.h>
#include <mach/reset.h>
#include <mach/i2c.h>
@@ -58,6 +58,66 @@
#include "devices.h"
#include "sharpsl.h"
+static unsigned long spitz_pin_config[] __initdata = {
+ /* Chip Selects */
+ GPIO78_nCS_2, /* SCOOP #2 */
+ GPIO80_nCS_4, /* SCOOP #1 */
+
+ /* LCD - 16bpp Active TFT */
+ GPIO58_LCD_LDD_0,
+ GPIO59_LCD_LDD_1,
+ GPIO60_LCD_LDD_2,
+ GPIO61_LCD_LDD_3,
+ GPIO62_LCD_LDD_4,
+ GPIO63_LCD_LDD_5,
+ GPIO64_LCD_LDD_6,
+ GPIO65_LCD_LDD_7,
+ GPIO66_LCD_LDD_8,
+ GPIO67_LCD_LDD_9,
+ GPIO68_LCD_LDD_10,
+ GPIO69_LCD_LDD_11,
+ GPIO70_LCD_LDD_12,
+ GPIO71_LCD_LDD_13,
+ GPIO72_LCD_LDD_14,
+ GPIO73_LCD_LDD_15,
+ GPIO74_LCD_FCLK,
+ GPIO75_LCD_LCLK,
+ GPIO76_LCD_PCLK,
+
+ /* PC Card */
+ GPIO48_nPOE,
+ GPIO49_nPWE,
+ GPIO50_nPIOR,
+ GPIO51_nPIOW,
+ GPIO85_nPCE_1,
+ GPIO54_nPCE_2,
+ GPIO79_PSKTSEL,
+ GPIO55_nPREG,
+ GPIO56_nPWAIT,
+ GPIO57_nIOIS16,
+
+ /* MMC */
+ GPIO32_MMC_CLK,
+ GPIO112_MMC_CMD,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+
+ /* GPIOs */
+ GPIO9_GPIO, /* SPITZ_GPIO_nSD_DETECT */
+ GPIO81_GPIO, /* SPITZ_GPIO_nSD_WP */
+ GPIO41_GPIO, /* SPITZ_GPIO_USB_CONNECT */
+ GPIO37_GPIO, /* SPITZ_GPIO_USB_HOST */
+ GPIO35_GPIO, /* SPITZ_GPIO_USB_DEVICE */
+ GPIO22_GPIO, /* SPITZ_GPIO_HSYNC */
+ GPIO94_GPIO, /* SPITZ_GPIO_CF_CD */
+ GPIO105_GPIO, /* SPITZ_GPIO_CF_IRQ */
+ GPIO106_GPIO, /* SPITZ_GPIO_CF2_IRQ */
+
+ GPIO1_GPIO | WAKEUP_ON_EDGE_RISE,
+};
+
/*
* Spitz SCOOP Device #1
*/
@@ -146,27 +206,6 @@
}
}
-static void spitz_pcmcia_init(void)
-{
- /* Setup default state of GPIO outputs
- before we enable them as outputs. */
- GPSR(GPIO48_nPOE) = GPIO_bit(GPIO48_nPOE) |
- GPIO_bit(GPIO49_nPWE) | GPIO_bit(GPIO50_nPIOR) |
- GPIO_bit(GPIO51_nPIOW) | GPIO_bit(GPIO54_nPCE_2);
- GPSR(GPIO85_nPCE_1) = GPIO_bit(GPIO85_nPCE_1);
-
- pxa_gpio_mode(GPIO48_nPOE_MD);
- pxa_gpio_mode(GPIO49_nPWE_MD);
- pxa_gpio_mode(GPIO50_nPIOR_MD);
- pxa_gpio_mode(GPIO51_nPIOW_MD);
- pxa_gpio_mode(GPIO55_nPREG_MD);
- pxa_gpio_mode(GPIO56_nPWAIT_MD);
- pxa_gpio_mode(GPIO57_nIOIS16_MD);
- pxa_gpio_mode(GPIO85_nPCE_1_MD);
- pxa_gpio_mode(GPIO54_nPCE_2_MD);
- pxa_gpio_mode(GPIO104_pSKTSEL_MD);
-}
-
static void spitz_pcmcia_pwr(struct device *scoop, unsigned short cpr, int nr)
{
/* Only need to override behaviour for slot 0 */
@@ -192,7 +231,6 @@
static struct scoop_pcmcia_config spitz_pcmcia_config = {
.devs = &spitz_pcmcia_scoop[0],
.num_devs = 2,
- .pcmcia_init = spitz_pcmcia_init,
.power_ctrl = spitz_pcmcia_pwr,
};
@@ -365,14 +403,6 @@
{
int err;
- /* setup GPIO for PXA27x MMC controller */
- pxa_gpio_mode(GPIO32_MMCCLK_MD);
- pxa_gpio_mode(GPIO112_MMCCMD_MD);
- pxa_gpio_mode(GPIO92_MMCDAT0_MD);
- pxa_gpio_mode(GPIO109_MMCDAT1_MD);
- pxa_gpio_mode(GPIO110_MMCDAT2_MD);
- pxa_gpio_mode(GPIO111_MMCDAT3_MD);
-
err = gpio_request(SPITZ_GPIO_nSD_DETECT, "nSD_DETECT");
if (err)
goto err_out;
@@ -447,12 +477,9 @@
if (err)
return err;
- /* Only Port 2 is connected */
- pxa_gpio_mode(SPITZ_GPIO_USB_CONNECT | GPIO_IN);
- pxa_gpio_mode(SPITZ_GPIO_USB_HOST | GPIO_OUT);
- pxa_gpio_mode(SPITZ_GPIO_USB_DEVICE | GPIO_IN);
-
- /* Setup USB Port 2 Output Control Register */
+ /* Only Port 2 is connected
+ * Setup USB Port 2 Output Control Register
+ */
UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
@@ -582,20 +609,12 @@
PMCR = 0x00;
- /* setup sleep mode values */
- PWER = 0x00000002;
- PFER = 0x00000000;
- PRER = 0x00000002;
- PGSR0 = 0x0158C000;
- PGSR1 = 0x00FF0080;
- PGSR2 = 0x0001C004;
-
/* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
PCFR |= PCFR_OPDE;
- corgi_ssp_set_machinfo(&spitz_ssp_machinfo);
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(spitz_pin_config));
- pxa_gpio_mode(SPITZ_GPIO_HSYNC | GPIO_IN);
+ corgi_ssp_set_machinfo(&spitz_ssp_machinfo);
platform_add_devices(devices, ARRAY_SIZE(devices));
pxa_set_mci_info(&spitz_mci_platform_data);