ARM: nomadik: delete old board files
The Device Tree support on Nomadik can do everything the old board
files could do, so delete the old board files and make the nomadik
select CONFIG_OF.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 67874b8..bef46ed 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -899,10 +899,12 @@
select ARCH_REQUIRE_GPIOLIB
select ARM_AMBA
select ARM_VIC
+ select CLKSRC_NOMADIK_MTU
select COMMON_CLK
select CPU_ARM926T
select GENERIC_CLOCKEVENTS
select MIGHT_HAVE_CACHE_L2X0
+ select OF
select PINCTRL
select PINCTRL_STN8815
select SPARSE_IRQ
diff --git a/arch/arm/mach-nomadik/Kconfig b/arch/arm/mach-nomadik/Kconfig
index 706dc57..82226a5 100644
--- a/arch/arm/mach-nomadik/Kconfig
+++ b/arch/arm/mach-nomadik/Kconfig
@@ -4,19 +4,13 @@
config MACH_NOMADIK_8815NHK
bool "ST 8815 Nomadik Hardware Kit (evaluation board)"
- select CLKSRC_NOMADIK_MTU
select NOMADIK_8815
+ select I2C
+ select I2C_ALGOBIT
endmenu
config NOMADIK_8815
bool
-config I2C_BITBANG_8815NHK
- tristate "Driver for bit-bang busses found on the 8815 NHK"
- depends on I2C && MACH_NOMADIK_8815NHK
- depends on PINCTRL_NOMADIK
- default y
- select I2C_ALGOBIT
-
endif
diff --git a/arch/arm/mach-nomadik/Makefile b/arch/arm/mach-nomadik/Makefile
index a42c9a3..1071c3b 100644
--- a/arch/arm/mach-nomadik/Makefile
+++ b/arch/arm/mach-nomadik/Makefile
@@ -9,9 +9,3 @@
# Cpu revision
obj-$(CONFIG_NOMADIK_8815) += cpu-8815.o
-
-# Specific board support
-obj-$(CONFIG_MACH_NOMADIK_8815NHK) += board-nhk8815.o
-
-# Nomadik extra devices
-obj-$(CONFIG_I2C_BITBANG_8815NHK) += i2c-8815nhk.o
diff --git a/arch/arm/mach-nomadik/board-nhk8815.c b/arch/arm/mach-nomadik/board-nhk8815.c
deleted file mode 100644
index e7b216c..0000000
--- a/arch/arm/mach-nomadik/board-nhk8815.c
+++ /dev/null
@@ -1,322 +0,0 @@
-/*
- * linux/arch/arm/mach-nomadik/board-8815nhk.c
- *
- * Copyright (C) STMicroelectronics
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2, as
- * published by the Free Software Foundation.
- *
- * NHK15 board specifc driver definition
- */
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/mmci.h>
-#include <linux/interrupt.h>
-#include <linux/gpio.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/fsmc.h>
-#include <linux/mtd/onenand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/i2c.h>
-#include <linux/io.h>
-#include <linux/platform_data/clocksource-nomadik-mtu.h>
-#include <asm/sizes.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/time.h>
-#include <mach/irqs.h>
-
-#include "cpu-8815.h"
-
-/* Initial value for SRC control register: all timers use MXTAL/8 source */
-#define SRC_CR_INIT_MASK 0x00007fff
-#define SRC_CR_INIT_VAL 0x2aaa8000
-
-#define ALE_OFF 0x1000000
-#define CLE_OFF 0x800000
-
-/* These addresses span 16MB, so use three individual pages */
-static struct resource nhk8815_nand_resources[] = {
- {
- .name = "nand_data",
- .start = 0x40000000,
- .end = 0x40000000 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .name = "nand_addr",
- .start = 0x40000000 + ALE_OFF,
- .end = 0x40000000 +ALE_OFF + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .name = "nand_cmd",
- .start = 0x40000000 + CLE_OFF,
- .end = 0x40000000 + CLE_OFF + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .name = "fsmc_regs",
- .start = NOMADIK_FSMC_BASE,
- .end = NOMADIK_FSMC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-/*
- * These partitions are the same as those used in the 2.6.20 release
- * shipped by the vendor; the first two partitions are mandated
- * by the boot ROM, and the bootloader area is somehow oversized...
- */
-static struct mtd_partition nhk8815_partitions[] = {
- {
- .name = "X-Loader(NAND)",
- .offset = 0,
- .size = SZ_256K,
- }, {
- .name = "MemInit(NAND)",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_256K,
- }, {
- .name = "BootLoader(NAND)",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_2M,
- }, {
- .name = "Kernel zImage(NAND)",
- .offset = MTDPART_OFS_APPEND,
- .size = 3 * SZ_1M,
- }, {
- .name = "Root Filesystem(NAND)",
- .offset = MTDPART_OFS_APPEND,
- .size = 22 * SZ_1M,
- }, {
- .name = "User Filesystem(NAND)",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- }
-};
-
-static struct fsmc_nand_timings nhk8815_nand_timings = {
- .thiz = 0,
- .thold = 0x10,
- .twait = 0x0A,
- .tset = 0,
-};
-
-static struct fsmc_nand_platform_data nhk8815_nand_platform_data = {
- .nand_timings = &nhk8815_nand_timings,
- .partitions = nhk8815_partitions,
- .nr_partitions = ARRAY_SIZE(nhk8815_partitions),
- .width = FSMC_NAND_BW8,
-};
-
-static struct platform_device nhk8815_nand_device = {
- .name = "fsmc-nand",
- .id = -1,
- .resource = nhk8815_nand_resources,
- .num_resources = ARRAY_SIZE(nhk8815_nand_resources),
- .dev = {
- .platform_data = &nhk8815_nand_platform_data,
- },
-};
-
-/* These are the partitions for the OneNand device, different from above */
-static struct mtd_partition nhk8815_onenand_partitions[] = {
- {
- .name = "X-Loader(OneNAND)",
- .offset = 0,
- .size = SZ_256K,
- }, {
- .name = "MemInit(OneNAND)",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_256K,
- }, {
- .name = "BootLoader(OneNAND)",
- .offset = MTDPART_OFS_APPEND,
- .size = SZ_2M-SZ_256K,
- }, {
- .name = "SysImage(OneNAND)",
- .offset = MTDPART_OFS_APPEND,
- .size = 4 * SZ_1M,
- }, {
- .name = "Root Filesystem(OneNAND)",
- .offset = MTDPART_OFS_APPEND,
- .size = 22 * SZ_1M,
- }, {
- .name = "User Filesystem(OneNAND)",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- }
-};
-
-static struct onenand_platform_data nhk8815_onenand_data = {
- .parts = nhk8815_onenand_partitions,
- .nr_parts = ARRAY_SIZE(nhk8815_onenand_partitions),
-};
-
-static struct resource nhk8815_onenand_resource[] = {
- {
- .start = 0x30000000,
- .end = 0x30000000 + SZ_128K - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device nhk8815_onenand_device = {
- .name = "onenand-flash",
- .id = -1,
- .dev = {
- .platform_data = &nhk8815_onenand_data,
- },
- .resource = nhk8815_onenand_resource,
- .num_resources = ARRAY_SIZE(nhk8815_onenand_resource),
-};
-
-/* bus control reg. and bus timing reg. for CS0..CS3 */
-#define FSMC_BCR(x) (NOMADIK_FSMC_VA + (x << 3))
-#define FSMC_BTR(x) (NOMADIK_FSMC_VA + (x << 3) + 0x04)
-
-static void __init nhk8815_onenand_init(void)
-{
-#ifdef CONFIG_MTD_ONENAND
- /* Set up SMCS0 for OneNand */
- writel(0x000030db, FSMC_BCR(0));
- writel(0x02100551, FSMC_BTR(0));
-#endif
-}
-
-static struct mmci_platform_data mmcsd_plat_data = {
- .ocr_mask = MMC_VDD_29_30,
- .f_max = 48000000,
- .gpio_wp = -1,
- .gpio_cd = 111,
- .cd_invert = true,
- .capabilities = MMC_CAP_MMC_HIGHSPEED |
- MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA,
-};
-
-static int __init nhk8815_mmcsd_init(void)
-{
- int ret;
-
- /* For e.g. devicetree boot */
- if (!machine_is_nomadik())
- return 0;
-
- ret = gpio_request(112, "card detect bias");
- if (ret)
- return ret;
- gpio_direction_output(112, 0);
- amba_apb_device_add(NULL, "mmci", NOMADIK_SDI_BASE, SZ_4K, IRQ_SDMMC, 0, &mmcsd_plat_data, 0x10180180);
- return 0;
-}
-module_init(nhk8815_mmcsd_init);
-
-static struct resource nhk8815_eth_resources[] = {
- {
- .name = "smc91x-regs",
- .start = 0x34000000 + 0x300,
- .end = 0x34000000 + SZ_64K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = NOMADIK_GPIO_TO_IRQ(115),
- .end = NOMADIK_GPIO_TO_IRQ(115),
- .flags = IORESOURCE_IRQ | IRQF_TRIGGER_RISING,
- }
-};
-
-static struct platform_device nhk8815_eth_device = {
- .name = "smc91x",
- .resource = nhk8815_eth_resources,
- .num_resources = ARRAY_SIZE(nhk8815_eth_resources),
-};
-
-static int __init nhk8815_eth_init(void)
-{
- int gpio_nr = 115; /* hardwired in the board */
- int err;
-
- if (!machine_is_nomadik())
- return 0;
- err = gpio_request(gpio_nr, "eth_irq");
- if (!err) err = gpio_direction_input(gpio_nr);
- if (err)
- pr_err("Error %i in %s\n", err, __func__);
- return err;
-}
-device_initcall(nhk8815_eth_init);
-
-static struct platform_device *nhk8815_platform_devices[] __initdata = {
- &nhk8815_nand_device,
- &nhk8815_onenand_device,
- &nhk8815_eth_device,
- /* will add more devices */
-};
-
-static void __init nomadik_timer_init(void)
-{
- u32 src_cr;
-
- /* Configure timer sources in "system reset controller" ctrl reg */
- src_cr = readl(io_p2v(NOMADIK_SRC_BASE));
- src_cr &= SRC_CR_INIT_MASK;
- src_cr |= SRC_CR_INIT_VAL;
- writel(src_cr, io_p2v(NOMADIK_SRC_BASE));
-
- nmdk_timer_init(io_p2v(NOMADIK_MTU0_BASE), IRQ_MTU0);
-}
-
-static struct i2c_board_info __initdata nhk8815_i2c0_devices[] = {
- {
- I2C_BOARD_INFO("stw4811", 0x2d),
- },
-};
-
-static struct i2c_board_info __initdata nhk8815_i2c1_devices[] = {
- {
- I2C_BOARD_INFO("camera", 0x10),
- },
- {
- I2C_BOARD_INFO("stw5095", 0x1a),
- },
- {
- I2C_BOARD_INFO("lis3lv02dl", 0x1d),
- },
-};
-
-static struct i2c_board_info __initdata nhk8815_i2c2_devices[] = {
- {
- I2C_BOARD_INFO("stw4811-usb", 0x2d),
- },
-};
-
-static void __init nhk8815_platform_init(void)
-{
- cpu8815_platform_init();
- nhk8815_onenand_init();
- platform_add_devices(nhk8815_platform_devices,
- ARRAY_SIZE(nhk8815_platform_devices));
-
- amba_apb_device_add(NULL, "uart0", NOMADIK_UART0_BASE, SZ_4K, IRQ_UART0, 0, NULL, 0);
- amba_apb_device_add(NULL, "uart1", NOMADIK_UART1_BASE, SZ_4K, IRQ_UART1, 0, NULL, 0);
-
- i2c_register_board_info(0, nhk8815_i2c0_devices,
- ARRAY_SIZE(nhk8815_i2c0_devices));
- i2c_register_board_info(1, nhk8815_i2c1_devices,
- ARRAY_SIZE(nhk8815_i2c1_devices));
- i2c_register_board_info(2, nhk8815_i2c2_devices,
- ARRAY_SIZE(nhk8815_i2c2_devices));
-}
-
-MACHINE_START(NOMADIK, "NHK8815")
- /* Maintainer: ST MicroElectronics */
- .atag_offset = 0x100,
- .map_io = cpu8815_map_io,
- .init_irq = cpu8815_init_irq,
- .init_time = nomadik_timer_init,
- .init_machine = nhk8815_platform_init,
- .restart = cpu8815_restart,
-MACHINE_END
diff --git a/arch/arm/mach-nomadik/cpu-8815.c b/arch/arm/mach-nomadik/cpu-8815.c
index 5ad301e..60a18e1 100644
--- a/arch/arm/mach-nomadik/cpu-8815.c
+++ b/arch/arm/mach-nomadik/cpu-8815.c
@@ -48,53 +48,6 @@
#include <asm/cacheflush.h>
#include <asm/hardware/cache-l2x0.h>
-#include "cpu-8815.h"
-
-/* The 8815 has 4 GPIO blocks, let's register them immediately */
-static resource_size_t __initdata cpu8815_gpio_base[] = {
- NOMADIK_GPIO0_BASE,
- NOMADIK_GPIO1_BASE,
- NOMADIK_GPIO2_BASE,
- NOMADIK_GPIO3_BASE,
-};
-
-static struct platform_device *
-cpu8815_add_gpio(int id, resource_size_t addr, int irq,
- struct nmk_gpio_platform_data *pdata)
-{
- struct resource resources[] = {
- {
- .start = addr,
- .end = addr + 127,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = irq,
- .end = irq,
- .flags = IORESOURCE_IRQ,
- }
- };
-
- return platform_device_register_resndata(NULL, "gpio", id,
- resources, ARRAY_SIZE(resources),
- pdata, sizeof(*pdata));
-}
-
-void cpu8815_add_gpios(resource_size_t *base, int num, int irq,
- struct nmk_gpio_platform_data *pdata)
-{
- int first = 0;
- int i;
-
- for (i = 0; i < num; i++, first += 32, irq++) {
- pdata->first_gpio = first;
- pdata->first_irq = NOMADIK_GPIO_TO_IRQ(first);
- pdata->num_gpio = 32;
-
- cpu8815_add_gpio(i, base[i], irq, pdata);
- }
-}
-
static unsigned long out_low[] = { PIN_OUTPUT_LOW };
static unsigned long out_high[] = { PIN_OUTPUT_HIGH };
static unsigned long in_nopull[] = { PIN_INPUT_NOPULL };
@@ -137,38 +90,6 @@
PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-stn8815", "GPIO74_C20", in_pullup),
};
-static inline void
-cpu8815_add_pinctrl(struct device *parent, const char *name)
-{
- struct platform_device_info pdevinfo = {
- .parent = parent,
- .name = name,
- .id = -1,
- };
-
- pinctrl_register_mappings(nhk8815_pinmap, ARRAY_SIZE(nhk8815_pinmap));
- platform_device_register_full(&pdevinfo);
-}
-
-static int __init cpu8815_init(void)
-{
- struct nmk_gpio_platform_data pdata = {
- /* No custom data yet */
- };
-
- /* For e.g. device tree boots */
- if (!machine_is_nomadik())
- return 0;
-
- cpu8815_add_gpios(cpu8815_gpio_base, ARRAY_SIZE(cpu8815_gpio_base),
- IRQ_GPIO0, &pdata);
- cpu8815_add_pinctrl(NULL, "pinctrl-stn8815");
- amba_apb_device_add(NULL, "rng", NOMADIK_RNG_BASE, SZ_4K, 0, 0, NULL, 0);
- amba_apb_device_add(NULL, "rtc-pl031", NOMADIK_RTC_BASE, SZ_4K, IRQ_RTC_RTT, 0, NULL, 0);
- return 0;
-}
-arch_initcall(cpu8815_init);
-
/* All SoC devices live in the same area (see hardware.h) */
static struct map_desc nomadik_io_desc[] __initdata = {
{
@@ -180,37 +101,12 @@
/* static ram and secured ram may be added later */
};
-void __init cpu8815_map_io(void)
+static void __init cpu8815_map_io(void)
{
iotable_init(nomadik_io_desc, ARRAY_SIZE(nomadik_io_desc));
}
-void __init cpu8815_init_irq(void)
-{
- /* This modified VIC cell has two register blocks, at 0 and 0x20 */
- vic_init(io_p2v(NOMADIK_IC_BASE + 0x00), IRQ_VIC_START + 0, ~0, 0);
- vic_init(io_p2v(NOMADIK_IC_BASE + 0x20), IRQ_VIC_START + 32, ~0, 0);
-
- /*
- * Init clocks here so that they are available for system timer
- * initialization.
- */
- nomadik_clk_init();
-}
-
-/*
- * This function is called from the board init ("init_machine").
- */
- void __init cpu8815_platform_init(void)
-{
-#ifdef CONFIG_CACHE_L2X0
- /* At full speed latency must be >=2, so 0x249 in low bits */
- l2x0_init(io_p2v(NOMADIK_L2CC_BASE), 0x00730249, 0xfe000fff);
-#endif
- return;
-}
-
-void cpu8815_restart(char mode, const char *cmd)
+static void cpu8815_restart(char mode, const char *cmd)
{
void __iomem *src_rstsr = io_p2v(NOMADIK_SRC_BASE + 0x18);
@@ -220,8 +116,6 @@
writel(1, src_rstsr);
}
-#ifdef CONFIG_OF
-
/* Initial value for SRC control register: all timers use MXTAL/8 source */
#define SRC_CR_INIT_MASK 0x00007fff
#define SRC_CR_INIT_VAL 0x2aaa8000
@@ -393,5 +287,3 @@
.restart = cpu8815_restart,
.dt_compat = cpu8815_board_compat,
MACHINE_END
-
-#endif
diff --git a/arch/arm/mach-nomadik/cpu-8815.h b/arch/arm/mach-nomadik/cpu-8815.h
deleted file mode 100644
index d6c7830..0000000
--- a/arch/arm/mach-nomadik/cpu-8815.h
+++ /dev/null
@@ -1,5 +0,0 @@
-extern void cpu8815_map_io(void);
-extern void cpu8815_platform_init(void);
-extern void cpu8815_init_irq(void);
-extern void cpu8815_restart(char, const char *);
-extern struct sys_timer cpu8815_timer;
diff --git a/arch/arm/mach-nomadik/i2c-8815nhk.c b/arch/arm/mach-nomadik/i2c-8815nhk.c
deleted file mode 100644
index 299ff5a..0000000
--- a/arch/arm/mach-nomadik/i2c-8815nhk.c
+++ /dev/null
@@ -1,82 +0,0 @@
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/i2c.h>
-#include <linux/i2c-algo-bit.h>
-#include <linux/i2c-gpio.h>
-#include <linux/platform_device.h>
-#include <asm/mach-types.h>
-
-/*
- * There are two busses in the 8815NHK.
- * They could, in theory, be driven by the hardware component, but we
- * use bit-bang through GPIO by now, to keep things simple
- */
-
-/* I2C0 connected to the STw4811 power management chip */
-static struct i2c_gpio_platform_data nhk8815_i2c_data0 = {
- /* keep defaults for timeouts; pins are push-pull bidirectional */
- .scl_pin = 62,
- .sda_pin = 63,
-};
-
-/* I2C1 connected to various sensors */
-static struct i2c_gpio_platform_data nhk8815_i2c_data1 = {
- /* keep defaults for timeouts; pins are push-pull bidirectional */
- .scl_pin = 53,
- .sda_pin = 54,
-};
-
-/* I2C2 connected to the USB portions of the STw4811 only */
-static struct i2c_gpio_platform_data nhk8815_i2c_data2 = {
- /* keep defaults for timeouts; pins are push-pull bidirectional */
- .scl_pin = 73,
- .sda_pin = 74,
-};
-
-static struct platform_device nhk8815_i2c_dev0 = {
- .name = "i2c-gpio",
- .id = 0,
- .dev = {
- .platform_data = &nhk8815_i2c_data0,
- },
-};
-
-static struct platform_device nhk8815_i2c_dev1 = {
- .name = "i2c-gpio",
- .id = 1,
- .dev = {
- .platform_data = &nhk8815_i2c_data1,
- },
-};
-
-static struct platform_device nhk8815_i2c_dev2 = {
- .name = "i2c-gpio",
- .id = 2,
- .dev = {
- .platform_data = &nhk8815_i2c_data2,
- },
-};
-
-static int __init nhk8815_i2c_init(void)
-{
- /* For e.g. devicetree boot */
- if (!machine_is_nomadik())
- return 0;
-
- platform_device_register(&nhk8815_i2c_dev0);
- platform_device_register(&nhk8815_i2c_dev1);
- platform_device_register(&nhk8815_i2c_dev2);
-
- return 0;
-}
-
-static void __exit nhk8815_i2c_exit(void)
-{
- platform_device_unregister(&nhk8815_i2c_dev0);
- platform_device_unregister(&nhk8815_i2c_dev1);
- platform_device_unregister(&nhk8815_i2c_dev2);
- return;
-}
-
-module_init(nhk8815_i2c_init);
-module_exit(nhk8815_i2c_exit);