| # |
| # Arcnet configuration |
| # |
| |
| menuconfig ARCNET |
| depends on NETDEVICES && (ISA || PCI || PCMCIA) |
| bool "ARCnet support" |
| ---help--- |
| If you have a network card of this type, say Y and check out the |
| (arguably) beautiful poetry in |
| <file:Documentation/networking/arcnet.txt>. |
| |
| You need both this driver, and the driver for the particular ARCnet |
| chipset of your card. If you don't know, then it's probably a |
| COM90xx type card, so say Y (or M) to "ARCnet COM90xx chipset |
| support" below. |
| |
| You might also want to have a look at the Ethernet-HOWTO, available |
| from <http://www.tldp.org/docs.html#howto>(even though ARCnet |
| is not really Ethernet). |
| |
| To compile this driver as a module, choose M here. The module will |
| be called arcnet. |
| |
| if ARCNET |
| |
| config ARCNET_1201 |
| tristate "Enable standard ARCNet packet format (RFC 1201)" |
| help |
| This allows you to use RFC1201 with your ARCnet card via the virtual |
| arc0 device. You need to say Y here to communicate with |
| industry-standard RFC1201 implementations, like the arcether.com |
| packet driver or most DOS/Windows ODI drivers. Please read the |
| ARCnet documentation in <file:Documentation/networking/arcnet.txt> |
| for more information about using arc0. |
| |
| config ARCNET_1051 |
| tristate "Enable old ARCNet packet format (RFC 1051)" |
| ---help--- |
| This allows you to use RFC1051 with your ARCnet card via the virtual |
| arc0s device. You only need arc0s if you want to talk to ARCnet |
| software complying with the "old" standard, specifically, the DOS |
| arcnet.com packet driver, Amigas running AmiTCP, and some variants |
| of NetBSD. You do not need to say Y here to communicate with |
| industry-standard RFC1201 implementations, like the arcether.com |
| packet driver or most DOS/Windows ODI drivers. RFC1201 is included |
| automatically as the arc0 device. Please read the ARCnet |
| documentation in <file:Documentation/networking/arcnet.txt> for more |
| information about using arc0e and arc0s. |
| |
| config ARCNET_RAW |
| tristate "Enable raw mode packet interface" |
| help |
| ARCnet "raw mode" packet encapsulation, no soft headers. Unlikely |
| to work unless talking to a copy of the same Linux arcnet driver, |
| but perhaps marginally faster in that case. |
| |
| config ARCNET_CAP |
| tristate "Enable CAP mode packet interface" |
| help |
| ARCnet "cap mode" packet encapsulation. Used to get the hardware |
| acknowledge back to userspace. After the initial protocol byte every |
| packet is stuffed with an extra 4 byte "cookie" which doesn't |
| actually appear on the network. After transmit the driver will send |
| back a packet with protocol byte 0 containing the status of the |
| transmission: |
| 0=no hardware acknowledge |
| 1=excessive nak |
| 2=transmission accepted by the receiver hardware |
| |
| Received packets are also stuffed with the extra 4 bytes but it will |
| be random data. |
| |
| Cap only listens to protocol 1-8. |
| |
| config ARCNET_COM90xx |
| tristate "ARCnet COM90xx (normal) chipset driver" |
| help |
| This is the chipset driver for the standard COM90xx cards. If you |
| have always used the old ARCnet driver without knowing what type of |
| card you had, this is probably the one for you. |
| |
| To compile this driver as a module, choose M here. The module will |
| be called com90xx. |
| |
| config ARCNET_COM90xxIO |
| tristate "ARCnet COM90xx (IO mapped) chipset driver" |
| ---help--- |
| This is the chipset driver for the COM90xx cards, using them in |
| IO-mapped mode instead of memory-mapped mode. This is slower than |
| the normal driver. Only use it if your card doesn't support shared |
| memory. |
| |
| To compile this driver as a module, choose M here. The module will |
| be called com90io. |
| |
| config ARCNET_RIM_I |
| tristate "ARCnet COM90xx (RIM I) chipset driver" |
| ---help--- |
| This is yet another chipset driver for the COM90xx cards, but this |
| time only using memory-mapped mode, and no IO ports at all. This |
| driver is completely untested, so if you have one of these cards, |
| please mail <dwmw2@infradead.org>, especially if it works! |
| |
| To compile this driver as a module, choose M here. The module will |
| be called arc-rimi. |
| |
| config ARCNET_COM20020 |
| tristate "ARCnet COM20020 chipset driver" |
| help |
| This is the driver for the new COM20020 chipset. It supports such |
| things as promiscuous mode, so packet sniffing is possible, and |
| extra diagnostic information. |
| |
| To compile this driver as a module, choose M here. The module will |
| be called com20020. |
| |
| config ARCNET_COM20020_ISA |
| tristate "Support for COM20020 on ISA" |
| depends on ARCNET_COM20020 && ISA |
| |
| config ARCNET_COM20020_PCI |
| tristate "Support for COM20020 on PCI" |
| depends on ARCNET_COM20020 && PCI |
| |
| config ARCNET_COM20020_CS |
| tristate "COM20020 ARCnet PCMCIA support" |
| depends on ARCNET_COM20020 && PCMCIA |
| help |
| Say Y here if you intend to attach this type of ARCnet PCMCIA card |
| to your computer. |
| |
| To compile this driver as a module, choose M here: the module will be |
| called com20020_cs. If unsure, say N. |
| |
| endif # ARCNET |