UAPI: (Scripted) Disintegrate include/linux
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
diff --git a/include/linux/lp.h b/include/linux/lp.h
index 0df024b..0dd276a 100644
--- a/include/linux/lp.h
+++ b/include/linux/lp.h
@@ -1,105 +1,16 @@
-#ifndef _LINUX_LP_H
-#define _LINUX_LP_H
-
/*
* usr/include/linux/lp.h c.1991-1992 James Wiegand
* many modifications copyright (C) 1992 Michael K. Johnson
* Interrupt support added 1993 Nigel Gamble
* Removed 8255 status defines from inside __KERNEL__ Marcelo Tosatti
*/
+#ifndef _LINUX_LP_H
+#define _LINUX_LP_H
-/*
- * Per POSIX guidelines, this module reserves the LP and lp prefixes
- * These are the lp_table[minor].flags flags...
- */
-#define LP_EXIST 0x0001
-#define LP_SELEC 0x0002
-#define LP_BUSY 0x0004
-#define LP_BUSY_BIT_POS 2
-#define LP_OFFL 0x0008
-#define LP_NOPA 0x0010
-#define LP_ERR 0x0020
-#define LP_ABORT 0x0040
-#define LP_CAREFUL 0x0080 /* obsoleted -arca */
-#define LP_ABORTOPEN 0x0100
-
-#define LP_TRUST_IRQ_ 0x0200 /* obsolete */
-#define LP_NO_REVERSE 0x0400 /* No reverse mode available. */
-#define LP_DATA_AVAIL 0x0800 /* Data is available. */
-
-/*
- * bit defines for 8255 status port
- * base + 1
- * accessed with LP_S(minor), which gets the byte...
- */
-#define LP_PBUSY 0x80 /* inverted input, active high */
-#define LP_PACK 0x40 /* unchanged input, active low */
-#define LP_POUTPA 0x20 /* unchanged input, active high */
-#define LP_PSELECD 0x10 /* unchanged input, active high */
-#define LP_PERRORP 0x08 /* unchanged input, active low */
-
-/* timeout for each character. This is relative to bus cycles -- it
- * is the count in a busy loop. THIS IS THE VALUE TO CHANGE if you
- * have extremely slow printing, or if the machine seems to slow down
- * a lot when you print. If you have slow printing, increase this
- * number and recompile, and if your system gets bogged down, decrease
- * this number. This can be changed with the tunelp(8) command as well.
- */
-
-#define LP_INIT_CHAR 1000
-
-/* The parallel port specs apparently say that there needs to be
- * a .5usec wait before and after the strobe.
- */
-
-#define LP_INIT_WAIT 1
-
-/* This is the amount of time that the driver waits for the printer to
- * catch up when the printer's buffer appears to be filled. If you
- * want to tune this and have a fast printer (i.e. HPIIIP), decrease
- * this number, and if you have a slow printer, increase this number.
- * This is in hundredths of a second, the default 2 being .05 second.
- * Or use the tunelp(8) command, which is especially nice if you want
- * change back and forth between character and graphics printing, which
- * are wildly different...
- */
-
-#define LP_INIT_TIME 2
-
-/* IOCTL numbers */
-#define LPCHAR 0x0601 /* corresponds to LP_INIT_CHAR */
-#define LPTIME 0x0602 /* corresponds to LP_INIT_TIME */
-#define LPABORT 0x0604 /* call with TRUE arg to abort on error,
- FALSE to retry. Default is retry. */
-#define LPSETIRQ 0x0605 /* call with new IRQ number,
- or 0 for polling (no IRQ) */
-#define LPGETIRQ 0x0606 /* get the current IRQ number */
-#define LPWAIT 0x0608 /* corresponds to LP_INIT_WAIT */
-/* NOTE: LPCAREFUL is obsoleted and it' s always the default right now -arca */
-#define LPCAREFUL 0x0609 /* call with TRUE arg to require out-of-paper, off-
- line, and error indicators good on all writes,
- FALSE to ignore them. Default is ignore. */
-#define LPABORTOPEN 0x060a /* call with TRUE arg to abort open() on error,
- FALSE to ignore error. Default is ignore. */
-#define LPGETSTATUS 0x060b /* return LP_S(minor) */
-#define LPRESET 0x060c /* reset printer */
-#ifdef LP_STATS
-#define LPGETSTATS 0x060d /* get statistics (struct lp_stats) */
-#endif
-#define LPGETFLAGS 0x060e /* get status flags */
-#define LPSETTIMEOUT 0x060f /* set parport timeout */
-
-/* timeout for printk'ing a timeout, in jiffies (100ths of a second).
- This is also used for re-checking error conditions if LP_ABORT is
- not set. This is the default behavior. */
-
-#define LP_TIMEOUT_INTERRUPT (60 * HZ)
-#define LP_TIMEOUT_POLLED (10 * HZ)
-
-#ifdef __KERNEL__
#include <linux/wait.h>
#include <linux/mutex.h>
+#include <uapi/linux/lp.h>
/* Magic numbers for defining port-device mappings */
#define LP_PARPORT_UNSPEC -4
@@ -187,5 +98,3 @@
#define LP_DELAY 50
#endif
-
-#endif