pcm038: Add SPI/MC13783 support
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
diff --git a/arch/arm/mach-mx2/pcm038.c b/arch/arm/mach-mx2/pcm038.c
index ee65dda..906d59b 100644
--- a/arch/arm/mach-mx2/pcm038.c
+++ b/arch/arm/mach-mx2/pcm038.c
@@ -23,6 +23,10 @@
#include <linux/mtd/plat-ram.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
+#include <linux/regulator/machine.h>
+#include <linux/mfd/mc13783.h>
+#include <linux/spi/spi.h>
+#include <linux/irq.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -35,6 +39,7 @@
#include <mach/iomux.h>
#include <mach/imx-uart.h>
#include <mach/mxc_nand.h>
+#include <mach/spi.h>
#include "devices.h"
@@ -78,8 +83,6 @@
PC6_PF_I2C2_SCL,
/* SPI1 */
PD25_PF_CSPI1_RDY,
- PD27_PF_CSPI1_SS1,
- PD28_PF_CSPI1_SS0,
PD29_PF_CSPI1_SCLK,
PD30_PF_CSPI1_MISO,
PD31_PF_CSPI1_MOSI,
@@ -196,6 +199,86 @@
}
};
+static int pcm038_spi_cs[] = {GPIO_PORTD + 28};
+
+static struct spi_imx_master pcm038_spi_0_data = {
+ .chipselect = pcm038_spi_cs,
+ .num_chipselect = ARRAY_SIZE(pcm038_spi_cs),
+};
+
+static struct regulator_consumer_supply sdhc1_consumers[] = {
+ {
+ .dev = &mxc_sdhc_device1.dev,
+ .supply = "sdhc_vcc",
+ },
+};
+
+static struct regulator_init_data sdhc1_data = {
+ .constraints = {
+ .min_uV = 3000000,
+ .max_uV = 3400000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL |
+ REGULATOR_MODE_FAST,
+ .always_on = 0,
+ .boot_on = 0,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(sdhc1_consumers),
+ .consumer_supplies = sdhc1_consumers,
+};
+
+static struct regulator_consumer_supply cam_consumers[] = {
+ {
+ .dev = NULL,
+ .supply = "imx_cam_vcc",
+ },
+};
+
+static struct regulator_init_data cam_data = {
+ .constraints = {
+ .min_uV = 3000000,
+ .max_uV = 3400000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL |
+ REGULATOR_MODE_FAST,
+ .always_on = 0,
+ .boot_on = 0,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(cam_consumers),
+ .consumer_supplies = cam_consumers,
+};
+
+struct mc13783_regulator_init_data pcm038_regulators[] = {
+ {
+ .id = MC13783_REGU_VCAM,
+ .init_data = &cam_data,
+ }, {
+ .id = MC13783_REGU_VMMC1,
+ .init_data = &sdhc1_data,
+ },
+};
+
+static struct mc13783_platform_data pcm038_pmic = {
+ .regulators = pcm038_regulators,
+ .num_regulators = ARRAY_SIZE(pcm038_regulators),
+ .flags = MC13783_USE_ADC | MC13783_USE_REGULATOR |
+ MC13783_USE_TOUCHSCREEN,
+};
+
+static struct spi_board_info pcm038_spi_board_info[] __initdata = {
+ {
+ .modalias = "mc13783",
+ .irq = IRQ_GPIOB(23),
+ .max_speed_hz = 300000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .platform_data = &pcm038_pmic,
+ .mode = SPI_CS_HIGH,
+ }
+};
+
static void __init pcm038_init(void)
{
mxc_gpio_setup_multiple_pins(pcm038_pins, ARRAY_SIZE(pcm038_pins),
@@ -219,6 +302,15 @@
/* PE18 for user-LED D40 */
mxc_gpio_mode(GPIO_PORTE | 18 | GPIO_GPIO | GPIO_OUT);
+ mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
+
+ /* MC13783 IRQ */
+ mxc_gpio_mode(GPIO_PORTB | 23 | GPIO_GPIO | GPIO_IN);
+
+ mxc_register_device(&mxc_spi_device0, &pcm038_spi_0_data);
+ spi_register_board_info(pcm038_spi_board_info,
+ ARRAY_SIZE(pcm038_spi_board_info));
+
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
#ifdef CONFIG_MACH_PCM970_BASEBOARD