ixgbe: Use generic MDIO definitions and functions
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 435bbc9..b8727d5 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2519,6 +2519,7 @@
config IXGBE
tristate "Intel(R) 10GbE PCI Express adapters support"
depends on PCI && INET
+ select MDIO
---help---
This driver supports Intel(R) 10GbE PCI Express family of
adapters. For more information on how to identify your adapter, go
diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c
index 03eb54f..e051964 100644
--- a/drivers/net/ixgbe/ixgbe_82598.c
+++ b/drivers/net/ixgbe/ixgbe_82598.c
@@ -229,14 +229,13 @@
*speed = 0;
*autoneg = true;
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_SPEED_ABILITY,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ status = hw->phy.ops.read_reg(hw, MDIO_SPEED, MDIO_MMD_PMAPMD,
&speed_ability);
if (status == 0) {
- if (speed_ability & IXGBE_MDIO_PHY_SPEED_10G)
+ if (speed_ability & MDIO_SPEED_10G)
*speed |= IXGBE_LINK_SPEED_10GB_FULL;
- if (speed_ability & IXGBE_MDIO_PHY_SPEED_1G)
+ if (speed_ability & MDIO_PMA_SPEED_1000)
*speed |= IXGBE_LINK_SPEED_1GB_FULL;
}
@@ -526,9 +525,9 @@
* clear indicates active; set indicates inactive.
*/
if (hw->phy.type == ixgbe_phy_nl) {
- hw->phy.ops.read_reg(hw, 0xC79F, IXGBE_TWINAX_DEV, &link_reg);
- hw->phy.ops.read_reg(hw, 0xC79F, IXGBE_TWINAX_DEV, &link_reg);
- hw->phy.ops.read_reg(hw, 0xC00C, IXGBE_TWINAX_DEV,
+ hw->phy.ops.read_reg(hw, 0xC79F, MDIO_MMD_PMAPMD, &link_reg);
+ hw->phy.ops.read_reg(hw, 0xC79F, MDIO_MMD_PMAPMD, &link_reg);
+ hw->phy.ops.read_reg(hw, 0xC00C, MDIO_MMD_PMAPMD,
&adapt_comp_reg);
if (link_up_wait_to_complete) {
for (i = 0; i < IXGBE_LINK_UP_TIME; i++) {
@@ -541,10 +540,10 @@
}
msleep(100);
hw->phy.ops.read_reg(hw, 0xC79F,
- IXGBE_TWINAX_DEV,
+ MDIO_MMD_PMAPMD,
&link_reg);
hw->phy.ops.read_reg(hw, 0xC00C,
- IXGBE_TWINAX_DEV,
+ MDIO_MMD_PMAPMD,
&adapt_comp_reg);
}
} else {
@@ -990,14 +989,14 @@
sfp_addr = (sfp_addr | IXGBE_I2C_EEPROM_READ_MASK);
hw->phy.ops.write_reg(hw,
IXGBE_MDIO_PMA_PMD_SDA_SCL_ADDR,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ MDIO_MMD_PMAPMD,
sfp_addr);
/* Poll status */
for (i = 0; i < 100; i++) {
hw->phy.ops.read_reg(hw,
IXGBE_MDIO_PMA_PMD_SDA_SCL_STAT,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ MDIO_MMD_PMAPMD,
&sfp_stat);
sfp_stat = sfp_stat & IXGBE_I2C_EEPROM_STATUS_MASK;
if (sfp_stat != IXGBE_I2C_EEPROM_STATUS_IN_PROGRESS)
@@ -1013,7 +1012,7 @@
/* Read data */
hw->phy.ops.read_reg(hw, IXGBE_MDIO_PMA_PMD_SDA_SCL_DATA,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE, &sfp_data);
+ MDIO_MMD_PMAPMD, &sfp_data);
*eeprom_data = (u8)(sfp_data >> 8);
} else {
@@ -1045,13 +1044,13 @@
* physical layer because 10GBase-T PHYs use LMS = KX4/KX */
if (hw->phy.type == ixgbe_phy_tn ||
hw->phy.type == ixgbe_phy_cu_unknown) {
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_EXT_ABILITY,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE, &ext_ability);
- if (ext_ability & IXGBE_MDIO_PHY_10GBASET_ABILITY)
+ hw->phy.ops.read_reg(hw, MDIO_PMA_EXTABLE, MDIO_MMD_PMAPMD,
+ &ext_ability);
+ if (ext_ability & MDIO_PMA_EXTABLE_10GBT)
physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T;
- if (ext_ability & IXGBE_MDIO_PHY_1000BASET_ABILITY)
+ if (ext_ability & MDIO_PMA_EXTABLE_1000BT)
physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
- if (ext_ability & IXGBE_MDIO_PHY_100BASETX_ABILITY)
+ if (ext_ability & MDIO_PMA_EXTABLE_100BTX)
physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX;
goto out;
}
diff --git a/drivers/net/ixgbe/ixgbe_82599.c b/drivers/net/ixgbe/ixgbe_82599.c
index 9e824b4..6038ed1 100644
--- a/drivers/net/ixgbe/ixgbe_82599.c
+++ b/drivers/net/ixgbe/ixgbe_82599.c
@@ -314,14 +314,13 @@
*speed = 0;
*autoneg = true;
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_SPEED_ABILITY,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ status = hw->phy.ops.read_reg(hw, MDIO_SPEED, MDIO_MMD_PMAPMD,
&speed_ability);
if (status == 0) {
- if (speed_ability & IXGBE_MDIO_PHY_SPEED_10G)
+ if (speed_ability & MDIO_SPEED_10G)
*speed |= IXGBE_LINK_SPEED_10GB_FULL;
- if (speed_ability & IXGBE_MDIO_PHY_SPEED_1G)
+ if (speed_ability & MDIO_PMA_SPEED_1000)
*speed |= IXGBE_LINK_SPEED_1GB_FULL;
}
@@ -1153,13 +1152,13 @@
if (hw->phy.type == ixgbe_phy_tn ||
hw->phy.type == ixgbe_phy_cu_unknown) {
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_EXT_ABILITY,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE, &ext_ability);
- if (ext_ability & IXGBE_MDIO_PHY_10GBASET_ABILITY)
+ hw->phy.ops.read_reg(hw, MDIO_PMA_EXTABLE, MDIO_MMD_PMAPMD,
+ &ext_ability);
+ if (ext_ability & MDIO_PMA_EXTABLE_10GBT)
physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T;
- if (ext_ability & IXGBE_MDIO_PHY_1000BASET_ABILITY)
+ if (ext_ability & MDIO_PMA_EXTABLE_1000BT)
physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
- if (ext_ability & IXGBE_MDIO_PHY_100BASETX_ABILITY)
+ if (ext_ability & MDIO_PMA_EXTABLE_100BTX)
physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX;
goto out;
}
diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index 01a8826..661bed6 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -4642,6 +4642,40 @@
return 0;
}
+static int
+ixgbe_mdio_read(struct net_device *netdev, int prtad, int devad, u16 addr)
+{
+ struct ixgbe_adapter *adapter = netdev_priv(netdev);
+ struct ixgbe_hw *hw = &adapter->hw;
+ u16 value;
+ int rc;
+
+ if (prtad != hw->phy.mdio.prtad)
+ return -EINVAL;
+ rc = hw->phy.ops.read_reg(hw, addr, devad, &value);
+ if (!rc)
+ rc = value;
+ return rc;
+}
+
+static int ixgbe_mdio_write(struct net_device *netdev, int prtad, int devad,
+ u16 addr, u16 value)
+{
+ struct ixgbe_adapter *adapter = netdev_priv(netdev);
+ struct ixgbe_hw *hw = &adapter->hw;
+
+ if (prtad != hw->phy.mdio.prtad)
+ return -EINVAL;
+ return hw->phy.ops.write_reg(hw, addr, devad, value);
+}
+
+static int ixgbe_ioctl(struct net_device *netdev, struct ifreq *req, int cmd)
+{
+ struct ixgbe_adapter *adapter = netdev_priv(netdev);
+
+ return mdio_mii_ioctl(&adapter->hw.phy.mdio, if_mii(req), cmd);
+}
+
#ifdef CONFIG_NET_POLL_CONTROLLER
/*
* Polling 'interrupt' - used by things like netconsole to send skbs
@@ -4675,6 +4709,7 @@
.ndo_vlan_rx_register = ixgbe_vlan_rx_register,
.ndo_vlan_rx_add_vid = ixgbe_vlan_rx_add_vid,
.ndo_vlan_rx_kill_vid = ixgbe_vlan_rx_kill_vid,
+ .ndo_do_ioctl = ixgbe_ioctl,
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_poll_controller = ixgbe_netpoll,
#endif
@@ -4789,6 +4824,13 @@
/* PHY */
memcpy(&hw->phy.ops, ii->phy_ops, sizeof(hw->phy.ops));
hw->phy.sfp_type = ixgbe_sfp_type_unknown;
+ /* ixgbe_identify_phy_generic will set prtad and mmds properly */
+ hw->phy.mdio.prtad = MDIO_PRTAD_NONE;
+ hw->phy.mdio.mmds = 0;
+ hw->phy.mdio.mode_support = MDIO_SUPPORTS_C45 | MDIO_EMULATE_C22;
+ hw->phy.mdio.dev = netdev;
+ hw->phy.mdio.mdio_read = ixgbe_mdio_read;
+ hw->phy.mdio.mdio_write = ixgbe_mdio_write;
/* set up this timer and work struct before calling get_invariants
* which might start the timer
diff --git a/drivers/net/ixgbe/ixgbe_phy.c b/drivers/net/ixgbe/ixgbe_phy.c
index 2543c32..6d385ea 100644
--- a/drivers/net/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ixgbe/ixgbe_phy.c
@@ -44,7 +44,6 @@
static s32 ixgbe_set_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl, bool data);
static bool ixgbe_get_i2c_data(u32 *i2cctl);
static void ixgbe_i2c_bus_clear(struct ixgbe_hw *hw);
-static bool ixgbe_validate_phy_addr(struct ixgbe_hw *hw, u32 phy_addr);
static enum ixgbe_phy_type ixgbe_get_phy_type_from_id(u32 phy_id);
static s32 ixgbe_get_phy_id(struct ixgbe_hw *hw);
@@ -61,8 +60,7 @@
if (hw->phy.type == ixgbe_phy_unknown) {
for (phy_addr = 0; phy_addr < IXGBE_MAX_PHY_ADDR; phy_addr++) {
- if (ixgbe_validate_phy_addr(hw, phy_addr)) {
- hw->phy.addr = phy_addr;
+ if (mdio45_probe(&hw->phy.mdio, phy_addr) == 0) {
ixgbe_get_phy_id(hw);
hw->phy.type =
ixgbe_get_phy_type_from_id(hw->phy.id);
@@ -78,26 +76,6 @@
}
/**
- * ixgbe_validate_phy_addr - Determines phy address is valid
- * @hw: pointer to hardware structure
- *
- **/
-static bool ixgbe_validate_phy_addr(struct ixgbe_hw *hw, u32 phy_addr)
-{
- u16 phy_id = 0;
- bool valid = false;
-
- hw->phy.addr = phy_addr;
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_ID_HIGH,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE, &phy_id);
-
- if (phy_id != 0xFFFF && phy_id != 0x0)
- valid = true;
-
- return valid;
-}
-
-/**
* ixgbe_get_phy_id - Get the phy type
* @hw: pointer to hardware structure
*
@@ -108,14 +86,12 @@
u16 phy_id_high = 0;
u16 phy_id_low = 0;
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_ID_HIGH,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ status = hw->phy.ops.read_reg(hw, MDIO_DEVID1, MDIO_MMD_PMAPMD,
&phy_id_high);
if (status == 0) {
hw->phy.id = (u32)(phy_id_high << 16);
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_ID_LOW,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ status = hw->phy.ops.read_reg(hw, MDIO_DEVID2, MDIO_MMD_PMAPMD,
&phy_id_low);
hw->phy.id |= (u32)(phy_id_low & IXGBE_PHY_REVISION_MASK);
hw->phy.revision = (u32)(phy_id_low & ~IXGBE_PHY_REVISION_MASK);
@@ -160,9 +136,8 @@
* Perform soft PHY reset to the PHY_XS.
* This will cause a soft reset to the PHY
*/
- return hw->phy.ops.write_reg(hw, IXGBE_MDIO_PHY_XS_CONTROL,
- IXGBE_MDIO_PHY_XS_DEV_TYPE,
- IXGBE_MDIO_PHY_XS_RESET);
+ return hw->phy.ops.write_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS,
+ MDIO_CTRL1_RESET);
}
/**
@@ -192,7 +167,7 @@
/* Setup and write the address cycle command */
command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
(device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) |
- (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
+ (hw->phy.mdio.prtad << IXGBE_MSCA_PHY_ADDR_SHIFT) |
(IXGBE_MSCA_ADDR_CYCLE | IXGBE_MSCA_MDI_COMMAND));
IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
@@ -223,7 +198,8 @@
*/
command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
(device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) |
- (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
+ (hw->phy.mdio.prtad <<
+ IXGBE_MSCA_PHY_ADDR_SHIFT) |
(IXGBE_MSCA_READ | IXGBE_MSCA_MDI_COMMAND));
IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
@@ -292,7 +268,7 @@
/* Setup and write the address cycle command */
command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
(device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) |
- (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
+ (hw->phy.mdio.prtad << IXGBE_MSCA_PHY_ADDR_SHIFT) |
(IXGBE_MSCA_ADDR_CYCLE | IXGBE_MSCA_MDI_COMMAND));
IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
@@ -323,7 +299,8 @@
*/
command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
(device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) |
- (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
+ (hw->phy.mdio.prtad <<
+ IXGBE_MSCA_PHY_ADDR_SHIFT) |
(IXGBE_MSCA_WRITE | IXGBE_MSCA_MDI_COMMAND));
IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
@@ -365,7 +342,7 @@
s32 status = IXGBE_NOT_IMPLEMENTED;
u32 time_out;
u32 max_time_out = 10;
- u16 autoneg_reg = IXGBE_MII_AUTONEG_REG;
+ u16 autoneg_reg;
/*
* Set advertisement settings in PHY based on autoneg_advertised
@@ -373,36 +350,31 @@
* tnx devices cannot be "forced" to a autoneg 10G and fail. But can
* for a 1G.
*/
- hw->phy.ops.read_reg(hw, IXGBE_MII_SPEED_SELECTION_REG,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
+ hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, MDIO_MMD_AN, &autoneg_reg);
if (hw->phy.autoneg_advertised == IXGBE_LINK_SPEED_1GB_FULL)
- autoneg_reg &= 0xEFFF; /* 0 in bit 12 is 1G operation */
+ autoneg_reg &= ~MDIO_AN_10GBT_CTRL_ADV10G;
else
- autoneg_reg |= 0x1000; /* 1 in bit 12 is 10G/1G operation */
+ autoneg_reg |= MDIO_AN_10GBT_CTRL_ADV10G;
- hw->phy.ops.write_reg(hw, IXGBE_MII_SPEED_SELECTION_REG,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
+ hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE, MDIO_MMD_AN, autoneg_reg);
/* Restart PHY autonegotiation and wait for completion */
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
+ hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_AN, &autoneg_reg);
- autoneg_reg |= IXGBE_MII_RESTART;
+ autoneg_reg |= MDIO_AN_CTRL1_RESTART;
- hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
+ hw->phy.ops.write_reg(hw, MDIO_CTRL1, MDIO_MMD_AN, autoneg_reg);
/* Wait for autonegotiation to finish */
for (time_out = 0; time_out < max_time_out; time_out++) {
udelay(10);
/* Restart PHY autonegotiation and wait for completion */
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ status = hw->phy.ops.read_reg(hw, MDIO_STAT1, MDIO_MMD_AN,
&autoneg_reg);
- autoneg_reg &= IXGBE_MII_AUTONEG_COMPLETE;
- if (autoneg_reg == IXGBE_MII_AUTONEG_COMPLETE) {
+ autoneg_reg &= MDIO_AN_STAT1_COMPLETE;
+ if (autoneg_reg == MDIO_AN_STAT1_COMPLETE) {
status = 0;
break;
}
@@ -457,23 +429,21 @@
s32 ret_val = 0;
u32 i;
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_XS_CONTROL,
- IXGBE_MDIO_PHY_XS_DEV_TYPE, &phy_data);
+ hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS, &phy_data);
/* reset the PHY and poll for completion */
- hw->phy.ops.write_reg(hw, IXGBE_MDIO_PHY_XS_CONTROL,
- IXGBE_MDIO_PHY_XS_DEV_TYPE,
- (phy_data | IXGBE_MDIO_PHY_XS_RESET));
+ hw->phy.ops.write_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS,
+ (phy_data | MDIO_CTRL1_RESET));
for (i = 0; i < 100; i++) {
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_XS_CONTROL,
- IXGBE_MDIO_PHY_XS_DEV_TYPE, &phy_data);
- if ((phy_data & IXGBE_MDIO_PHY_XS_RESET) == 0)
+ hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS,
+ &phy_data);
+ if ((phy_data & MDIO_CTRL1_RESET) == 0)
break;
msleep(10);
}
- if ((phy_data & IXGBE_MDIO_PHY_XS_RESET) != 0) {
+ if ((phy_data & MDIO_CTRL1_RESET) != 0) {
hw_dbg(hw, "PHY reset did not complete.\n");
ret_val = IXGBE_ERR_PHY;
goto out;
@@ -509,7 +479,7 @@
for (i = 0; i < edata; i++) {
hw->eeprom.ops.read(hw, data_offset, &eword);
hw->phy.ops.write_reg(hw, phy_offset,
- IXGBE_TWINAX_DEV, eword);
+ MDIO_MMD_PMAPMD, eword);
hw_dbg(hw, "Wrote %4.4x to %4.4x\n", eword,
phy_offset);
data_offset++;
@@ -1302,7 +1272,7 @@
udelay(10);
status = hw->phy.ops.read_reg(hw,
IXGBE_MDIO_VENDOR_SPECIFIC_1_STATUS,
- IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ MDIO_MMD_VEND1,
&phy_data);
phy_link = phy_data &
IXGBE_MDIO_VENDOR_SPECIFIC_1_LINK_STATUS;
@@ -1330,8 +1300,7 @@
{
s32 status = 0;
- status = hw->phy.ops.read_reg(hw, TNX_FW_REV,
- IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ status = hw->phy.ops.read_reg(hw, TNX_FW_REV, MDIO_MMD_VEND1,
firmware_version);
return status;
diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h
index bdfdf3b..e49e8af 100644
--- a/drivers/net/ixgbe/ixgbe_type.h
+++ b/drivers/net/ixgbe/ixgbe_type.h
@@ -29,6 +29,7 @@
#define _IXGBE_TYPE_H_
#include <linux/types.h>
+#include <linux/mdio.h>
/* Vendor ID */
#define IXGBE_INTEL_VENDOR_ID 0x8086
@@ -848,13 +849,7 @@
/* Omer bit masks */
#define IXGBE_CORECTL_WRITE_CMD 0x00010000
-/* Device Type definitions for new protocol MDIO commands */
-#define IXGBE_MDIO_PMA_PMD_DEV_TYPE 0x1
-#define IXGBE_MDIO_PCS_DEV_TYPE 0x3
-#define IXGBE_MDIO_PHY_XS_DEV_TYPE 0x4
-#define IXGBE_MDIO_AUTO_NEG_DEV_TYPE 0x7
-#define IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE 0x1E /* Device 30 */
-#define IXGBE_TWINAX_DEV 1
+/* MDIO definitions */
#define IXGBE_MDIO_COMMAND_TIMEOUT 100 /* PHY Timeout for 1 GB mode */
@@ -865,32 +860,10 @@
#define IXGBE_MDIO_VENDOR_SPECIFIC_1_10G_SPEED 0x0018
#define IXGBE_MDIO_VENDOR_SPECIFIC_1_1G_SPEED 0x0010
-#define IXGBE_MDIO_AUTO_NEG_CONTROL 0x0 /* AUTO_NEG Control Reg */
-#define IXGBE_MDIO_AUTO_NEG_STATUS 0x1 /* AUTO_NEG Status Reg */
-#define IXGBE_MDIO_PHY_XS_CONTROL 0x0 /* PHY_XS Control Reg */
-#define IXGBE_MDIO_PHY_XS_RESET 0x8000 /* PHY_XS Reset */
-#define IXGBE_MDIO_PHY_ID_HIGH 0x2 /* PHY ID High Reg*/
-#define IXGBE_MDIO_PHY_ID_LOW 0x3 /* PHY ID Low Reg*/
-#define IXGBE_MDIO_PHY_SPEED_ABILITY 0x4 /* Speed Ability Reg */
-#define IXGBE_MDIO_PHY_SPEED_10G 0x0001 /* 10G capable */
-#define IXGBE_MDIO_PHY_SPEED_1G 0x0010 /* 1G capable */
-#define IXGBE_MDIO_PHY_EXT_ABILITY 0xB /* Ext Ability Reg */
-#define IXGBE_MDIO_PHY_10GBASET_ABILITY 0x0004 /* 10GBaseT capable */
-#define IXGBE_MDIO_PHY_1000BASET_ABILITY 0x0020 /* 1000BaseT capable */
-#define IXGBE_MDIO_PHY_100BASETX_ABILITY 0x0080 /* 100BaseTX capable */
-
#define IXGBE_MDIO_PMA_PMD_SDA_SCL_ADDR 0xC30A /* PHY_XS SDA/SCL Addr Reg */
#define IXGBE_MDIO_PMA_PMD_SDA_SCL_DATA 0xC30B /* PHY_XS SDA/SCL Data Reg */
#define IXGBE_MDIO_PMA_PMD_SDA_SCL_STAT 0xC30C /* PHY_XS SDA/SCL Status Reg */
-/* MII clause 22/28 definitions */
-#define IXGBE_MDIO_PHY_LOW_POWER_MODE 0x0800
-
-#define IXGBE_MII_SPEED_SELECTION_REG 0x10
-#define IXGBE_MII_RESTART 0x200
-#define IXGBE_MII_AUTONEG_COMPLETE 0x20
-#define IXGBE_MII_AUTONEG_REG 0x0
-
#define IXGBE_PHY_REVISION_MASK 0xFFFFFFF0
#define IXGBE_MAX_PHY_ADDR 32
@@ -2214,8 +2187,8 @@
struct ixgbe_phy_info {
struct ixgbe_phy_operations ops;
+ struct mdio_if_info mdio;
enum ixgbe_phy_type type;
- u32 addr;
u32 id;
enum ixgbe_sfp_type sfp_type;
bool sfp_setup_needed;