Merge remote-tracking branches 'spi/topic/davinci', 'spi/topic/doc', 'spi/topic/dw' and 'spi/topic/fsl' into spi-next
diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt
index f80887b..12ecfe9 100644
--- a/Documentation/devicetree/bindings/spi/spi-davinci.txt
+++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt
@@ -1,5 +1,10 @@
 Davinci SPI controller device bindings
 
+Links on DM:
+Keystone 2 - http://www.ti.com/lit/ug/sprugp2a/sprugp2a.pdf
+dm644x - http://www.ti.com/lit/ug/sprue32a/sprue32a.pdf
+OMAP-L138/da830 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf
+
 Required properties:
 - #address-cells: number of cells required to define a chip select
 	address on the SPI bus. Should be set to 1.
@@ -24,6 +29,30 @@
 	cs-gpios = <0>, <0>, <0>, <&gpio1 30 0>, <&gpio1 31 0>;
 	where first three are internal CS and last two are GPIO CS.
 
+Optional properties for slave devices:
+SPI slave nodes can contain the following properties.
+Not all SPI Peripherals from Texas Instruments support this.
+Please check SPI peripheral documentation for a device before using these.
+
+- ti,spi-wdelay : delay between transmission of words
+	(SPIFMTn.WDELAY, SPIDAT1.WDEL) must be specified in number of SPI module
+	clock periods.
+
+	delay = WDELAY * SPI_module_clock_period + 2 * SPI_module_clock_period
+
+Below is timing diagram which shows functional meaning of
+"ti,spi-wdelay" parameter.
+
+             +-+ +-+ +-+ +-+ +-+                           +-+ +-+ +-+
+SPI_CLK      | | | | | | | | | |                           | | | | | |
+  +----------+ +-+ +-+ +-+ +-+ +---------------------------+ +-+ +-+ +-
+
+SPI_SOMI/SIMO+-----------------+                           +-----------
+  +----------+ word1           +---------------------------+word2
+             +-----------------+                           +-----------
+                                          WDELAY
+                                <-------------------------->
+
 Example of a NOR flash slave device (n25q032) connected to DaVinci
 SPI controller device over the SPI bus.
 
@@ -43,6 +72,7 @@
 		compatible = "st,m25p32";
 		spi-max-frequency = <25000000>;
 		reg = <0>;
+		ti,spi-wdelay = <8>;
 
 		partition@0 {
 			label = "u-boot-spl";
diff --git a/Documentation/spi/spi-summary b/Documentation/spi/spi-summary
index 7982bcc..d29734b 100644
--- a/Documentation/spi/spi-summary
+++ b/Documentation/spi/spi-summary
@@ -601,13 +601,13 @@
 Contributors to Linux-SPI discussions include (in alphabetical order,
 by last name):
 
+Mark Brown
 David Brownell
 Russell King
+Grant Likely
 Dmitry Pervushin
 Stephen Street
 Mark Underwood
 Andrew Victor
-Vitaly Wool
-Grant Likely
-Mark Brown
 Linus Walleij
+Vitaly Wool
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index a862a1c..c4f1988 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -602,7 +602,7 @@
 	depends on SPI_DESIGNWARE && PCI
 
 config SPI_DW_MID_DMA
-	bool "DMA support for DW SPI controller on Intel Moorestown platform"
+	bool "DMA support for DW SPI controller on Intel MID platform"
 	depends on SPI_DW_PCI && INTEL_MID_DMAC
 
 config SPI_DW_MMIO
diff --git a/drivers/spi/spi-davinci.c b/drivers/spi/spi-davinci.c
index 63c82a61..63700ab 100644
--- a/drivers/spi/spi-davinci.c
+++ b/drivers/spi/spi-davinci.c
@@ -65,6 +65,7 @@
 
 /* SPIDAT1 (upper 16 bit defines) */
 #define SPIDAT1_CSHOLD_MASK	BIT(12)
+#define SPIDAT1_WDEL		BIT(10)
 
 /* SPIGCR1 */
 #define SPIGCR1_CLKMOD_MASK	BIT(1)
@@ -213,6 +214,7 @@
 {
 	struct davinci_spi *dspi;
 	struct davinci_spi_platform_data *pdata;
+	struct davinci_spi_config *spicfg = spi->controller_data;
 	u8 chip_sel = spi->chip_select;
 	u16 spidat1 = CS_DEFAULT;
 	bool gpio_chipsel = false;
@@ -227,6 +229,10 @@
 		gpio = spi->cs_gpio;
 	}
 
+	/* program delay transfers if tx_delay is non zero */
+	if (spicfg->wdelay)
+		spidat1 |= SPIDAT1_WDEL;
+
 	/*
 	 * Board specific chip select logic decides the polarity and cs
 	 * line for the controller
@@ -241,9 +247,9 @@
 			spidat1 |= SPIDAT1_CSHOLD_MASK;
 			spidat1 &= ~(0x1 << chip_sel);
 		}
-
-		iowrite16(spidat1, dspi->base + SPIDAT1 + 2);
 	}
+
+	iowrite16(spidat1, dspi->base + SPIDAT1 + 2);
 }
 
 /**
@@ -289,7 +295,7 @@
 	int prescale;
 
 	dspi = spi_master_get_devdata(spi->master);
-	spicfg = (struct davinci_spi_config *)spi->controller_data;
+	spicfg = spi->controller_data;
 	if (!spicfg)
 		spicfg = &davinci_spi_default_cfg;
 
@@ -337,6 +343,14 @@
 		spifmt |= SPIFMT_PHASE_MASK;
 
 	/*
+	* Assume wdelay is used only on SPI peripherals that has this field
+	* in SPIFMTn register and when it's configured from board file or DT.
+	*/
+	if (spicfg->wdelay)
+		spifmt |= ((spicfg->wdelay << SPIFMT_WDELAY_SHIFT)
+				& SPIFMT_WDELAY_MASK);
+
+	/*
 	 * Version 1 hardware supports two basic SPI modes:
 	 *  - Standard SPI mode uses 4 pins, with chipselect
 	 *  - 3 pin SPI is a 4 pin variant without CS (SPI_NO_CS)
@@ -353,9 +367,6 @@
 
 		u32 delay = 0;
 
-		spifmt |= ((spicfg->wdelay << SPIFMT_WDELAY_SHIFT)
-							& SPIFMT_WDELAY_MASK);
-
 		if (spicfg->odd_parity)
 			spifmt |= SPIFMT_ODD_PARITY_MASK;
 
@@ -387,6 +398,26 @@
 	return 0;
 }
 
+static int davinci_spi_of_setup(struct spi_device *spi)
+{
+	struct davinci_spi_config *spicfg = spi->controller_data;
+	struct device_node *np = spi->dev.of_node;
+	u32 prop;
+
+	if (spicfg == NULL && np) {
+		spicfg = kzalloc(sizeof(*spicfg), GFP_KERNEL);
+		if (!spicfg)
+			return -ENOMEM;
+		*spicfg = davinci_spi_default_cfg;
+		/* override with dt configured values */
+		if (!of_property_read_u32(np, "ti,spi-wdelay", &prop))
+			spicfg->wdelay = (u8)prop;
+		spi->controller_data = spicfg;
+	}
+
+	return 0;
+}
+
 /**
  * davinci_spi_setup - This functions will set default transfer method
  * @spi: spi device on which data transfer to be done
@@ -437,7 +468,16 @@
 	else
 		clear_io_bits(dspi->base + SPIGCR1, SPIGCR1_LOOPBACK_MASK);
 
-	return retval;
+	return davinci_spi_of_setup(spi);
+}
+
+static void davinci_spi_cleanup(struct spi_device *spi)
+{
+	struct davinci_spi_config *spicfg = spi->controller_data;
+
+	spi->controller_data = NULL;
+	if (spi->dev.of_node)
+		kfree(spicfg);
 }
 
 static int davinci_spi_check_error(struct davinci_spi *dspi, int int_status)
@@ -951,6 +991,7 @@
 	master->num_chipselect = pdata->num_chipselect;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(2, 16);
 	master->setup = davinci_spi_setup;
+	master->cleanup = davinci_spi_cleanup;
 
 	dspi->bitbang.chipselect = davinci_spi_chipselect;
 	dspi->bitbang.setup_transfer = davinci_spi_setup_transfer;
diff --git a/drivers/spi/spi-dw-mid.c b/drivers/spi/spi-dw-mid.c
index 6d207af..46c6d58 100644
--- a/drivers/spi/spi-dw-mid.c
+++ b/drivers/spi/spi-dw-mid.c
@@ -1,7 +1,7 @@
 /*
  * Special handling for DW core on Intel MID platform
  *
- * Copyright (c) 2009, Intel Corporation.
+ * Copyright (c) 2009, 2014 Intel Corporation.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms and conditions of the GNU General Public License,
@@ -11,10 +11,6 @@
  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  * more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation,
- * Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
  */
 
 #include <linux/dma-mapping.h>
@@ -39,22 +35,25 @@
 {
 	struct dw_spi *dws = param;
 
-	return dws->dmac && (&dws->dmac->dev == chan->device->dev);
+	return dws->dma_dev == chan->device->dev;
 }
 
 static int mid_spi_dma_init(struct dw_spi *dws)
 {
 	struct mid_dma *dw_dma = dws->dma_priv;
+	struct pci_dev *dma_dev;
 	struct intel_mid_dma_slave *rxs, *txs;
 	dma_cap_mask_t mask;
 
 	/*
 	 * Get pci device for DMA controller, currently it could only
-	 * be the DMA controller of either Moorestown or Medfield
+	 * be the DMA controller of Medfield
 	 */
-	dws->dmac = pci_get_device(PCI_VENDOR_ID_INTEL, 0x0813, NULL);
-	if (!dws->dmac)
-		dws->dmac = pci_get_device(PCI_VENDOR_ID_INTEL, 0x0827, NULL);
+	dma_dev = pci_get_device(PCI_VENDOR_ID_INTEL, 0x0827, NULL);
+	if (!dma_dev)
+		return -ENODEV;
+
+	dws->dma_dev = &dma_dev->dev;
 
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_SLAVE, mask);
@@ -83,13 +82,18 @@
 free_rxchan:
 	dma_release_channel(dws->rxchan);
 err_exit:
-	return -1;
-
+	return -EBUSY;
 }
 
 static void mid_spi_dma_exit(struct dw_spi *dws)
 {
+	if (!dws->dma_inited)
+		return;
+
+	dmaengine_terminate_all(dws->txchan);
 	dma_release_channel(dws->txchan);
+
+	dmaengine_terminate_all(dws->rxchan);
 	dma_release_channel(dws->rxchan);
 }
 
@@ -109,8 +113,7 @@
 
 static int mid_spi_dma_transfer(struct dw_spi *dws, int cs_change)
 {
-	struct dma_async_tx_descriptor *txdesc = NULL, *rxdesc = NULL;
-	struct dma_chan *txchan, *rxchan;
+	struct dma_async_tx_descriptor *txdesc, *rxdesc;
 	struct dma_slave_config txconf, rxconf;
 	u16 dma_ctrl = 0;
 
@@ -120,37 +123,34 @@
 		dw_writew(dws, DW_SPI_DMARDLR, 0xf);
 		dw_writew(dws, DW_SPI_DMATDLR, 0x10);
 		if (dws->tx_dma)
-			dma_ctrl |= 0x2;
+			dma_ctrl |= SPI_DMA_TDMAE;
 		if (dws->rx_dma)
-			dma_ctrl |= 0x1;
+			dma_ctrl |= SPI_DMA_RDMAE;
 		dw_writew(dws, DW_SPI_DMACR, dma_ctrl);
 		spi_enable_chip(dws, 1);
 	}
 
 	dws->dma_chan_done = 0;
-	txchan = dws->txchan;
-	rxchan = dws->rxchan;
 
 	/* 2. Prepare the TX dma transfer */
 	txconf.direction = DMA_MEM_TO_DEV;
 	txconf.dst_addr = dws->dma_addr;
 	txconf.dst_maxburst = LNW_DMA_MSIZE_16;
 	txconf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
-	txconf.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+	txconf.dst_addr_width = dws->dma_width;
 	txconf.device_fc = false;
 
-	txchan->device->device_control(txchan, DMA_SLAVE_CONFIG,
-				       (unsigned long) &txconf);
+	dmaengine_slave_config(dws->txchan, &txconf);
 
 	memset(&dws->tx_sgl, 0, sizeof(dws->tx_sgl));
 	dws->tx_sgl.dma_address = dws->tx_dma;
 	dws->tx_sgl.length = dws->len;
 
-	txdesc = dmaengine_prep_slave_sg(txchan,
+	txdesc = dmaengine_prep_slave_sg(dws->txchan,
 				&dws->tx_sgl,
 				1,
 				DMA_MEM_TO_DEV,
-				DMA_PREP_INTERRUPT);
+				DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 	txdesc->callback = dw_spi_dma_done;
 	txdesc->callback_param = dws;
 
@@ -159,27 +159,30 @@
 	rxconf.src_addr = dws->dma_addr;
 	rxconf.src_maxburst = LNW_DMA_MSIZE_16;
 	rxconf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
-	rxconf.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+	rxconf.src_addr_width = dws->dma_width;
 	rxconf.device_fc = false;
 
-	rxchan->device->device_control(rxchan, DMA_SLAVE_CONFIG,
-				       (unsigned long) &rxconf);
+	dmaengine_slave_config(dws->rxchan, &rxconf);
 
 	memset(&dws->rx_sgl, 0, sizeof(dws->rx_sgl));
 	dws->rx_sgl.dma_address = dws->rx_dma;
 	dws->rx_sgl.length = dws->len;
 
-	rxdesc = dmaengine_prep_slave_sg(rxchan,
+	rxdesc = dmaengine_prep_slave_sg(dws->rxchan,
 				&dws->rx_sgl,
 				1,
 				DMA_DEV_TO_MEM,
-				DMA_PREP_INTERRUPT);
+				DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 	rxdesc->callback = dw_spi_dma_done;
 	rxdesc->callback_param = dws;
 
 	/* rx must be started before tx due to spi instinct */
-	rxdesc->tx_submit(rxdesc);
-	txdesc->tx_submit(txdesc);
+	dmaengine_submit(rxdesc);
+	dma_async_issue_pending(dws->rxchan);
+
+	dmaengine_submit(txdesc);
+	dma_async_issue_pending(dws->txchan);
+
 	return 0;
 }
 
@@ -190,7 +193,7 @@
 };
 #endif
 
-/* Some specific info for SPI0 controller on Moorestown */
+/* Some specific info for SPI0 controller on Intel MID */
 
 /* HW info for MRST CLk Control Unit, one 32b reg */
 #define MRST_SPI_CLK_BASE	100000000	/* 100m */
diff --git a/drivers/spi/spi-dw-pci.c b/drivers/spi/spi-dw-pci.c
index e149604..ba68da1 100644
--- a/drivers/spi/spi-dw-pci.c
+++ b/drivers/spi/spi-dw-pci.c
@@ -1,7 +1,7 @@
 /*
  * PCI interface driver for DW SPI Core
  *
- * Copyright (c) 2009, Intel Corporation.
+ * Copyright (c) 2009, 2014 Intel Corporation.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms and conditions of the GNU General Public License,
@@ -11,10 +11,6 @@
  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  * more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation,
- * Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
  */
 
 #include <linux/interrupt.h>
@@ -32,17 +28,22 @@
 	struct dw_spi	dws;
 };
 
-static int spi_pci_probe(struct pci_dev *pdev,
-	const struct pci_device_id *ent)
+struct spi_pci_desc {
+	int	(*setup)(struct dw_spi *);
+};
+
+static struct spi_pci_desc spi_pci_mid_desc = {
+	.setup = dw_spi_mid_init,
+};
+
+static int spi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	struct dw_spi_pci *dwpci;
 	struct dw_spi *dws;
+	struct spi_pci_desc *desc = (struct spi_pci_desc *)ent->driver_data;
 	int pci_bar = 0;
 	int ret;
 
-	dev_info(&pdev->dev, "found PCI SPI controller(ID: %04x:%04x)\n",
-		pdev->vendor, pdev->device);
-
 	ret = pcim_enable_device(pdev);
 	if (ret)
 		return ret;
@@ -58,7 +59,7 @@
 	/* Get basic io resource and map it */
 	dws->paddr = pci_resource_start(pdev, pci_bar);
 
-	ret = pcim_iomap_regions(pdev, 1, dev_name(&pdev->dev));
+	ret = pcim_iomap_regions(pdev, 1 << pci_bar, pci_name(pdev));
 	if (ret)
 		return ret;
 
@@ -69,11 +70,11 @@
 	dws->irq = pdev->irq;
 
 	/*
-	 * Specific handling for Intel MID paltforms, like dma setup,
+	 * Specific handling for paltforms, like dma setup,
 	 * clock rate, FIFO depth.
 	 */
-	if (pdev->device == 0x0800) {
-		ret = dw_spi_mid_init(dws);
+	if (desc && desc->setup) {
+		ret = desc->setup(dws);
 		if (ret)
 			return ret;
 	}
@@ -85,6 +86,9 @@
 	/* PCI hook and SPI hook use the same drv data */
 	pci_set_drvdata(pdev, dwpci);
 
+	dev_info(&pdev->dev, "found PCI SPI controller(ID: %04x:%04x)\n",
+		pdev->vendor, pdev->device);
+
 	return 0;
 }
 
@@ -95,41 +99,29 @@
 	dw_spi_remove_host(&dwpci->dws);
 }
 
-#ifdef CONFIG_PM
-static int spi_suspend(struct pci_dev *pdev, pm_message_t state)
+#ifdef CONFIG_PM_SLEEP
+static int spi_suspend(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct dw_spi_pci *dwpci = pci_get_drvdata(pdev);
-	int ret;
 
-	ret = dw_spi_suspend_host(&dwpci->dws);
-	if (ret)
-		return ret;
-	pci_save_state(pdev);
-	pci_disable_device(pdev);
-	pci_set_power_state(pdev, pci_choose_state(pdev, state));
-	return ret;
+	return dw_spi_suspend_host(&dwpci->dws);
 }
 
-static int spi_resume(struct pci_dev *pdev)
+static int spi_resume(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct dw_spi_pci *dwpci = pci_get_drvdata(pdev);
-	int ret;
 
-	pci_set_power_state(pdev, PCI_D0);
-	pci_restore_state(pdev);
-	ret = pci_enable_device(pdev);
-	if (ret)
-		return ret;
 	return dw_spi_resume_host(&dwpci->dws);
 }
-#else
-#define spi_suspend	NULL
-#define spi_resume	NULL
 #endif
 
+static SIMPLE_DEV_PM_OPS(dw_spi_pm_ops, spi_suspend, spi_resume);
+
 static const struct pci_device_id pci_ids[] = {
 	/* Intel MID platform SPI controller 0 */
-	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x0800) },
+	{ PCI_VDEVICE(INTEL, 0x0800), (kernel_ulong_t)&spi_pci_mid_desc},
 	{},
 };
 
@@ -138,8 +130,9 @@
 	.id_table =	pci_ids,
 	.probe =	spi_pci_probe,
 	.remove =	spi_pci_remove,
-	.suspend =	spi_suspend,
-	.resume	=	spi_resume,
+	.driver         = {
+		.pm     = &dw_spi_pm_ops,
+	},
 };
 
 module_pci_driver(dw_spi_driver);
diff --git a/drivers/spi/spi-dw.c b/drivers/spi/spi-dw.c
index 33117fb..7292158 100644
--- a/drivers/spi/spi-dw.c
+++ b/drivers/spi/spi-dw.c
@@ -11,10 +11,6 @@
  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
  */
 
 #include <linux/dma-mapping.h>
@@ -59,22 +55,20 @@
 
 #ifdef CONFIG_DEBUG_FS
 #define SPI_REGS_BUFSIZE	1024
-static ssize_t  spi_show_regs(struct file *file, char __user *user_buf,
-				size_t count, loff_t *ppos)
+static ssize_t dw_spi_show_regs(struct file *file, char __user *user_buf,
+		size_t count, loff_t *ppos)
 {
-	struct dw_spi *dws;
+	struct dw_spi *dws = file->private_data;
 	char *buf;
 	u32 len = 0;
 	ssize_t ret;
 
-	dws = file->private_data;
-
 	buf = kzalloc(SPI_REGS_BUFSIZE, GFP_KERNEL);
 	if (!buf)
 		return 0;
 
 	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
-			"MRST SPI0 registers:\n");
+			"%s registers:\n", dev_name(&dws->master->dev));
 	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"=================================\n");
 	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
@@ -110,41 +104,41 @@
 	len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
 			"=================================\n");
 
-	ret =  simple_read_from_buffer(user_buf, count, ppos, buf, len);
+	ret = simple_read_from_buffer(user_buf, count, ppos, buf, len);
 	kfree(buf);
 	return ret;
 }
 
-static const struct file_operations mrst_spi_regs_ops = {
+static const struct file_operations dw_spi_regs_ops = {
 	.owner		= THIS_MODULE,
 	.open		= simple_open,
-	.read		= spi_show_regs,
+	.read		= dw_spi_show_regs,
 	.llseek		= default_llseek,
 };
 
-static int mrst_spi_debugfs_init(struct dw_spi *dws)
+static int dw_spi_debugfs_init(struct dw_spi *dws)
 {
-	dws->debugfs = debugfs_create_dir("mrst_spi", NULL);
+	dws->debugfs = debugfs_create_dir("dw_spi", NULL);
 	if (!dws->debugfs)
 		return -ENOMEM;
 
 	debugfs_create_file("registers", S_IFREG | S_IRUGO,
-		dws->debugfs, (void *)dws, &mrst_spi_regs_ops);
+		dws->debugfs, (void *)dws, &dw_spi_regs_ops);
 	return 0;
 }
 
-static void mrst_spi_debugfs_remove(struct dw_spi *dws)
+static void dw_spi_debugfs_remove(struct dw_spi *dws)
 {
 	debugfs_remove_recursive(dws->debugfs);
 }
 
 #else
-static inline int mrst_spi_debugfs_init(struct dw_spi *dws)
+static inline int dw_spi_debugfs_init(struct dw_spi *dws)
 {
 	return 0;
 }
 
-static inline void mrst_spi_debugfs_remove(struct dw_spi *dws)
+static inline void dw_spi_debugfs_remove(struct dw_spi *dws)
 {
 }
 #endif /* CONFIG_DEBUG_FS */
@@ -396,7 +390,7 @@
 		goto early_exit;
 	}
 
-	/* Delay if requested at end of transfer*/
+	/* Delay if requested at end of transfer */
 	if (message->state == RUNNING_STATE) {
 		previous = list_entry(transfer->transfer_list.prev,
 					struct spi_transfer,
@@ -525,7 +519,7 @@
 	struct dw_spi *dws = spi_master_get_devdata(master);
 
 	dws->cur_msg = msg;
-	/* Initial message state*/
+	/* Initial message state */
 	dws->cur_msg->state = START_STATE;
 	dws->cur_transfer = list_entry(dws->cur_msg->transfers.next,
 						struct spi_transfer,
@@ -596,6 +590,9 @@
 			| (spi->mode  << SPI_MODE_OFFSET)
 			| (chip->tmode << SPI_TMOD_OFFSET);
 
+	if (spi->mode & SPI_LOOP)
+		chip->cr0 |= 1 << SPI_SRL_OFFSET;
+
 	if (gpio_is_valid(spi->cs_gpio)) {
 		ret = gpio_direction_output(spi->cs_gpio,
 				!(spi->mode & SPI_CS_HIGH));
@@ -655,8 +652,7 @@
 	dws->prev_chip = NULL;
 	dws->dma_inited = 0;
 	dws->dma_addr = (dma_addr_t)(dws->paddr + 0x60);
-	snprintf(dws->name, sizeof(dws->name), "dw_spi%d",
-			dws->bus_num);
+	snprintf(dws->name, sizeof(dws->name), "dw_spi%d", dws->bus_num);
 
 	ret = devm_request_irq(dev, dws->irq, dw_spi_irq, IRQF_SHARED,
 			dws->name, dws);
@@ -665,7 +661,7 @@
 		goto err_free_master;
 	}
 
-	master->mode_bits = SPI_CPOL | SPI_CPHA;
+	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LOOP;
 	master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
 	master->bus_num = dws->bus_num;
 	master->num_chipselect = dws->num_cs;
@@ -694,7 +690,7 @@
 		goto err_dma_exit;
 	}
 
-	mrst_spi_debugfs_init(dws);
+	dw_spi_debugfs_init(dws);
 	return 0;
 
 err_dma_exit:
@@ -711,7 +707,7 @@
 {
 	if (!dws)
 		return;
-	mrst_spi_debugfs_remove(dws);
+	dw_spi_debugfs_remove(dws);
 
 	if (dws->dma_ops && dws->dma_ops->dma_exit)
 		dws->dma_ops->dma_exit(dws);
diff --git a/drivers/spi/spi-dw.h b/drivers/spi/spi-dw.h
index 6d2acad..83a103a 100644
--- a/drivers/spi/spi-dw.h
+++ b/drivers/spi/spi-dw.h
@@ -74,6 +74,10 @@
 #define SPI_INT_RXFI			(1 << 4)
 #define SPI_INT_MSTI			(1 << 5)
 
+/* Bit fields in DMACR */
+#define SPI_DMA_RDMAE			(1 << 0)
+#define SPI_DMA_TDMAE			(1 << 1)
+
 /* TX RX interrupt level threshold, max can be 256 */
 #define SPI_INT_THRESHOLD		32
 
@@ -140,7 +144,6 @@
 	dma_addr_t		dma_addr; /* phy address of the Data register */
 	struct dw_spi_dma_ops	*dma_ops;
 	void			*dma_priv; /* platform relate info */
-	struct pci_dev		*dmac;
 
 	/* Bus interface info */
 	void			*priv;
@@ -217,11 +220,11 @@
  * Each SPI slave device to work with dw_api controller should
  * has such a structure claiming its working mode (PIO/DMA etc),
  * which can be save in the "controller_data" member of the
- * struct spi_device
+ * struct spi_device.
  */
 struct dw_spi_chip {
-	u8 poll_mode;	/* 0 for contoller polling mode */
-	u8 type;	/* SPI/SSP/Micrwire */
+	u8 poll_mode;	/* 1 for controller polling mode */
+	u8 type;	/* SPI/SSP/MicroWire */
 	u8 enable_dma;
 	void (*cs_control)(u32 command);
 };
diff --git a/drivers/spi/spi-fsl-cpm.c b/drivers/spi/spi-fsl-cpm.c
index 54b0637..c5dd20b 100644
--- a/drivers/spi/spi-fsl-cpm.c
+++ b/drivers/spi/spi-fsl-cpm.c
@@ -15,17 +15,17 @@
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
  */
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/spi/spi.h>
-#include <linux/fsl_devices.h>
-#include <linux/dma-mapping.h>
-#include <linux/of_address.h>
 #include <asm/cpm.h>
 #include <asm/qe.h>
+#include <linux/dma-mapping.h>
+#include <linux/fsl_devices.h>
+#include <linux/kernel.h>
+#include <linux/of_address.h>
+#include <linux/spi/spi.h>
+#include <linux/types.h>
 
-#include "spi-fsl-lib.h"
 #include "spi-fsl-cpm.h"
+#include "spi-fsl-lib.h"
 #include "spi-fsl-spi.h"
 
 /* CPM1 and CPM2 are mutually exclusive. */
diff --git a/drivers/spi/spi-fsl-dspi.c b/drivers/spi/spi-fsl-dspi.c
index 5021ddf..63c3859 100644
--- a/drivers/spi/spi-fsl-dspi.c
+++ b/drivers/spi/spi-fsl-dspi.c
@@ -13,22 +13,22 @@
  *
  */
 
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/errno.h>
-#include <linux/platform_device.h>
-#include <linux/regmap.h>
-#include <linux/sched.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/spi_bitbang.h>
-#include <linux/pm_runtime.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/sched.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
 
 #define DRIVER_NAME "fsl-dspi"
 
diff --git a/drivers/spi/spi-fsl-espi.c b/drivers/spi/spi-fsl-espi.c
index 429e111..a7f94b6 100644
--- a/drivers/spi/spi-fsl-espi.c
+++ b/drivers/spi/spi-fsl-espi.c
@@ -8,19 +8,19 @@
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
  */
-#include <linux/module.h>
 #include <linux/delay.h>
-#include <linux/irq.h>
-#include <linux/spi/spi.h>
-#include <linux/platform_device.h>
+#include <linux/err.h>
 #include <linux/fsl_devices.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
 #include <linux/mm.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
-#include <linux/interrupt.h>
-#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
 #include <sysdev/fsl_soc.h>
 
 #include "spi-fsl-lib.h"
diff --git a/drivers/spi/spi-fsl-lib.c b/drivers/spi/spi-fsl-lib.c
index e0b773f..5ddb5b0 100644
--- a/drivers/spi/spi-fsl-lib.c
+++ b/drivers/spi/spi-fsl-lib.c
@@ -16,10 +16,10 @@
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
  */
-#include <linux/kernel.h>
-#include <linux/interrupt.h>
-#include <linux/fsl_devices.h>
 #include <linux/dma-mapping.h>
+#include <linux/fsl_devices.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
 #include <linux/mm.h>
 #include <linux/of_platform.h>
 #include <linux/spi/spi.h>
diff --git a/drivers/spi/spi-fsl-spi.c b/drivers/spi/spi-fsl-spi.c
index 590f31b..ed79288 100644
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -19,25 +19,25 @@
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
  */
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/interrupt.h>
 #include <linux/delay.h>
-#include <linux/irq.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/spi_bitbang.h>
-#include <linux/platform_device.h>
-#include <linux/fsl_devices.h>
 #include <linux/dma-mapping.h>
+#include <linux/fsl_devices.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
 #include <linux/mm.h>
+#include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/of.h>
-#include <linux/of_platform.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
-#include <linux/gpio.h>
 #include <linux/of_gpio.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
+#include <linux/types.h>
 
 #include "spi-fsl-lib.h"
 #include "spi-fsl-cpm.h"