arch/arm64/boot/dts/qcom/lito-rumi.dtsi

// SPDX-License-Identifier: GPL-2.0-only
/*
 * Copyright  (c) 2018 , The Linux Foundation. All rights reserved.
 */

&soc {
	timer {
		clock-frequency = <500000>;
	};

	timer@17c20000 {
		clock-frequency = <500000>;
	};

	usb_emu_phy: usb_emu_phy@a720000 {
		compatible = "qcom,usb-emu-phy";
		reg = <0x0a720000 0x9500>,
		      <0x0a6f8800 0x100>;
		reg-names = "base", "qscratch_base";

		qcom,emu-init-seq = <0xfff0 0x4
				     0xfff3 0x4
				     0x40 0x4
				     0xfff3 0x4
				     0xfff0 0x4
				     0x100000 0x20
				     0x0 0x20
				     0x1a0 0x20
				     0x100000 0x3c
				     0x0 0x3c
				     0x10060 0x3c
				     0x0 0x4>;
	};

	usb_nop_phy: usb_nop_phy {
		compatible = "usb-nop-xceiv";
	};

	cxo: bi_tcxo {
		compatible = "fixed-factor-clock";
		clocks = <&xo_board>;
		clock-mult = <1>;
		clock-div = <2>;
		#clock-cells = <0>;
	};

	cxo_a: bi_tcxo_ao {
		compatible = "fixed-factor-clock";
		clocks = <&xo_board>;
		clock-mult = <1>;
		clock-div = <2>;
		#clock-cells = <0>;
	};
};

&rpmhcc {
	compatible = "qcom,dummycc";
	clock-output-names = "rpmh_clocks";
};

&aopcc {
	compatible = "qcom,dummycc";
	clock-output-names = "qdss_clocks";
};

&usb0 {
	dwc3@a600000 {
		usb-phy = <&usb_emu_phy>, <&usb_nop_phy>;
		maximum-speed = "high-speed";
	};
};

&qupv3_se8_2uart {
	status = "disabled";
};

/*RUMI UART console*/
&qupv3_se2_2uart {
	status = "ok";
};

&wdog {
	status = "disabled";
};

&ufsphy_mem {
	compatible = "qcom,ufs-phy-qrbtc-sdm845";

	vdda-phy-supply = <&pm8150_l5>;
	vdda-pll-supply = <&pm8150_l6>;
	vdda-phy-max-microamp = <90200>;
	vdda-pll-max-microamp = <19000>;

	status = "ok";
};

&ufshc_mem {
	limit-tx-hs-gear = <1>;
	limit-rx-hs-gear = <1>;

	vdd-hba-supply = <&ufs_phy_gdsc>;
	vdd-hba-fixed-regulator;
	vcc-supply = <&pm8150a_l7>;
	vccq2-supply = <&pm8150_s4>;
	vcc-max-microamp = <800000>;
	vccq2-max-microamp = <800000>;

	qcom,vddp-ref-clk-supply = <&pm8150_l6>;
	qcom,vddp-ref-clk-max-microamp = <100>;

	qcom,disable-lpm;
	rpm-level = <0>;
	spm-level = <0>;
	status = "ok";
};