arch/arm/mach-mx5/board-cpuimx51sd.c - kernel/msm-4.19 - Gitiles

 /*
  *
  * Copyright (C) 2010 Eric Bénard <eric@eukrea.com>
  *
  * based on board-mx51_babbage.c which is
  * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
  * Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License
  * Version 2 or later at the following locations:
  *
  * http://www.opensource.org/licenses/gpl-license.html
  * http://www.gnu.org/copyleft/gpl.html
  */

 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/i2c.h>
 #include <linux/i2c/tsc2007.h>
 #include <linux/gpio.h>
 #include <linux/delay.h>
 #include <linux/io.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/i2c-gpio.h>
 #include <linux/spi/spi.h>
 #include <linux/can/platform/mcp251x.h>

 #include <mach/eukrea-baseboards.h>
 #include <mach/common.h>
 #include <mach/hardware.h>
 #include <mach/iomux-mx51.h>

 #include <asm/irq.h>
 #include <asm/setup.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>

 #include "devices-imx51.h"
 #include "devices.h"
 #include "cpu_op-mx51.h"

 #define USBH1_RST		IMX_GPIO_NR(2, 28)
 #define ETH_RST			IMX_GPIO_NR(2, 31)
 #define TSC2007_IRQGPIO		IMX_GPIO_NR(3, 12)
 #define CAN_IRQGPIO		IMX_GPIO_NR(1, 1)
 #define CAN_RST			IMX_GPIO_NR(4, 15)
 #define CAN_NCS			IMX_GPIO_NR(4, 24)
 #define CAN_RXOBF		IMX_GPIO_NR(1, 4)
 #define CAN_RX1BF		IMX_GPIO_NR(1, 6)
 #define CAN_TXORTS		IMX_GPIO_NR(1, 7)
 #define CAN_TX1RTS		IMX_GPIO_NR(1, 8)
 #define CAN_TX2RTS		IMX_GPIO_NR(1, 9)
 #define I2C_SCL			IMX_GPIO_NR(4, 16)
 #define I2C_SDA			IMX_GPIO_NR(4, 17)

 /* USB_CTRL_1 */
 #define MX51_USB_CTRL_1_OFFSET		0x10
 #define MX51_USB_CTRL_UH1_EXT_CLK_EN	(1 << 25)

 #define	MX51_USB_PLLDIV_12_MHZ		0x00
 #define	MX51_USB_PLL_DIV_19_2_MHZ	0x01
 #define	MX51_USB_PLL_DIV_24_MHZ		0x02

 static iomux_v3_cfg_t eukrea_cpuimx51sd_pads[] = {
 	/* UART1 */
 	MX51_PAD_UART1_RXD__UART1_RXD,
 	MX51_PAD_UART1_TXD__UART1_TXD,
 	MX51_PAD_UART1_RTS__UART1_RTS,
 	MX51_PAD_UART1_CTS__UART1_CTS,

 	/* USB HOST1 */
 	MX51_PAD_USBH1_CLK__USBH1_CLK,
 	MX51_PAD_USBH1_DIR__USBH1_DIR,
 	MX51_PAD_USBH1_NXT__USBH1_NXT,
 	MX51_PAD_USBH1_DATA0__USBH1_DATA0,
 	MX51_PAD_USBH1_DATA1__USBH1_DATA1,
 	MX51_PAD_USBH1_DATA2__USBH1_DATA2,
 	MX51_PAD_USBH1_DATA3__USBH1_DATA3,
 	MX51_PAD_USBH1_DATA4__USBH1_DATA4,
 	MX51_PAD_USBH1_DATA5__USBH1_DATA5,
 	MX51_PAD_USBH1_DATA6__USBH1_DATA6,
 	MX51_PAD_USBH1_DATA7__USBH1_DATA7,
 	MX51_PAD_USBH1_STP__USBH1_STP,
 	MX51_PAD_EIM_CS3__GPIO2_28,		/* PHY nRESET */

 	/* FEC */
 	MX51_PAD_EIM_DTACK__GPIO2_31,		/* PHY nRESET */

 	/* HSI2C */
 	MX51_PAD_I2C1_CLK__GPIO4_16,
 	MX51_PAD_I2C1_DAT__GPIO4_17,

 	/* CAN */
 	MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
 	MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
 	MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
 	MX51_PAD_CSPI1_SS0__GPIO4_24,		/* nCS */
 	MX51_PAD_CSI2_PIXCLK__GPIO4_15,		/* nReset */
 	MX51_PAD_GPIO1_1__GPIO1_1,		/* IRQ */
 	MX51_PAD_GPIO1_4__GPIO1_4,		/* Control signals */
 	MX51_PAD_GPIO1_6__GPIO1_6,
 	MX51_PAD_GPIO1_7__GPIO1_7,
 	MX51_PAD_GPIO1_8__GPIO1_8,
 	MX51_PAD_GPIO1_9__GPIO1_9,

 	/* Touchscreen */
 	/* IRQ */
 	NEW_PAD_CTRL(MX51_PAD_GPIO_NAND__GPIO_NAND, PAD_CTL_PUS_22K_UP |
 			PAD_CTL_PKE | PAD_CTL_SRE_FAST |
 			PAD_CTL_DSE_HIGH | PAD_CTL_PUE | PAD_CTL_HYS),
 };

 static const struct imxuart_platform_data uart_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };

 static struct tsc2007_platform_data tsc2007_info = {
 	.model			= 2007,
 	.x_plate_ohms		= 180,
 };

 static struct i2c_board_info eukrea_cpuimx51sd_i2c_devices[] = {
 	{
 		I2C_BOARD_INFO("pcf8563", 0x51),
 	}, {
 		I2C_BOARD_INFO("tsc2007", 0x49),
 		.type		= "tsc2007",
 		.platform_data	= &tsc2007_info,
 		.irq		= gpio_to_irq(TSC2007_IRQGPIO),
 	},
 };

 static const struct mxc_nand_platform_data
 		eukrea_cpuimx51sd_nand_board_info __initconst = {
 	.width		= 1,
 	.hw_ecc		= 1,
 	.flash_bbt	= 1,
 };

 /* This function is board specific as the bit mask for the plldiv will also
 be different for other Freescale SoCs, thus a common bitmask is not
 possible and cannot get place in /plat-mxc/ehci.c.*/
 static int initialize_otg_port(struct platform_device *pdev)
 {
 	u32 v;
 	void __iomem *usb_base;
 	void __iomem *usbother_base;

 	usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
 	if (!usb_base)
 		return -ENOMEM;
 	usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;

 	/* Set the PHY clock to 19.2MHz */
 	v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
 	v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
 	v |= MX51_USB_PLL_DIV_19_2_MHZ;
 	__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
 	iounmap(usb_base);

 	mdelay(10);

 	return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
 }

 static int initialize_usbh1_port(struct platform_device *pdev)
 {
 	u32 v;
 	void __iomem *usb_base;
 	void __iomem *usbother_base;

 	usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
 	if (!usb_base)
 		return -ENOMEM;
 	usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;

 	/* The clock for the USBH1 ULPI port will come from the PHY. */
 	v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
 	__raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN,
 			usbother_base + MX51_USB_CTRL_1_OFFSET);
 	iounmap(usb_base);

 	mdelay(10);

 	return mx51_initialize_usb_hw(1, MXC_EHCI_POWER_PINS_ENABLED |
 			MXC_EHCI_ITC_NO_THRESHOLD);
 }

 static struct mxc_usbh_platform_data dr_utmi_config = {
 	.init		= initialize_otg_port,
 	.portsc	= MXC_EHCI_UTMI_16BIT,
 };

 static struct fsl_usb2_platform_data usb_pdata = {
 	.operating_mode	= FSL_USB2_DR_DEVICE,
 	.phy_mode	= FSL_USB2_PHY_UTMI_WIDE,
 };

 static struct mxc_usbh_platform_data usbh1_config = {
 	.init		= initialize_usbh1_port,
 	.portsc	= MXC_EHCI_MODE_ULPI,
 };

 static int otg_mode_host;

 static int __init eukrea_cpuimx51sd_otg_mode(char *options)
 {
 	if (!strcmp(options, "host"))
 		otg_mode_host = 1;
 	else if (!strcmp(options, "device"))
 		otg_mode_host = 0;
 	else
 		pr_info("otg_mode neither \"host\" nor \"device\". "
 			"Defaulting to device\n");
 	return 0;
 }
 __setup("otg_mode=", eukrea_cpuimx51sd_otg_mode);

 static struct i2c_gpio_platform_data pdata = {
 	.sda_pin		= I2C_SDA,
 	.sda_is_open_drain	= 0,
 	.scl_pin		= I2C_SCL,
 	.scl_is_open_drain	= 0,
 	.udelay			= 2,
 };

 static struct platform_device hsi2c_gpio_device = {
 	.name			= "i2c-gpio",
 	.id			= 0,
 	.dev.platform_data	= &pdata,
 };

 static struct mcp251x_platform_data mcp251x_info = {
 	.oscillator_frequency = 24E6,
 };

 static struct spi_board_info cpuimx51sd_spi_device[] = {
 	{
 		.modalias        = "mcp2515",
 		.max_speed_hz    = 10000000,
 		.bus_num         = 0,
 		.mode		= SPI_MODE_0,
 		.chip_select     = 0,
 		.platform_data   = &mcp251x_info,
 		.irq             = gpio_to_irq(CAN_IRQGPIO)
 	},
 };

 static int cpuimx51sd_spi1_cs[] = {
 	CAN_NCS,
 };

 static const struct spi_imx_master cpuimx51sd_ecspi1_pdata __initconst = {
 	.chipselect	= cpuimx51sd_spi1_cs,
 	.num_chipselect	= ARRAY_SIZE(cpuimx51sd_spi1_cs),
 };

 static struct platform_device *platform_devices[] __initdata = {
 	&hsi2c_gpio_device,
 };

 static void __init eukrea_cpuimx51sd_init(void)
 {
 	imx51_soc_init();

 	mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51sd_pads,
 					ARRAY_SIZE(eukrea_cpuimx51sd_pads));

 #if defined(CONFIG_CPU_FREQ_IMX)
 	get_cpu_op = mx51_get_cpu_op;
 #endif

 	imx51_add_imx_uart(0, &uart_pdata);
 	imx51_add_mxc_nand(&eukrea_cpuimx51sd_nand_board_info);

 	gpio_request(ETH_RST, "eth_rst");
 	gpio_set_value(ETH_RST, 1);
 	imx51_add_fec(NULL);

 	gpio_request(CAN_IRQGPIO, "can_irq");
 	gpio_direction_input(CAN_IRQGPIO);
 	gpio_free(CAN_IRQGPIO);
 	gpio_request(CAN_NCS, "can_ncs");
 	gpio_direction_output(CAN_NCS, 1);
 	gpio_free(CAN_NCS);
 	gpio_request(CAN_RST, "can_rst");
 	gpio_direction_output(CAN_RST, 0);
 	msleep(20);
 	gpio_set_value(CAN_RST, 1);
 	imx51_add_ecspi(0, &cpuimx51sd_ecspi1_pdata);
 	spi_register_board_info(cpuimx51sd_spi_device,
 				ARRAY_SIZE(cpuimx51sd_spi_device));

 	gpio_request(TSC2007_IRQGPIO, "tsc2007_irq");
 	gpio_direction_input(TSC2007_IRQGPIO);
 	gpio_free(TSC2007_IRQGPIO);

 	i2c_register_board_info(0, eukrea_cpuimx51sd_i2c_devices,
 			ARRAY_SIZE(eukrea_cpuimx51sd_i2c_devices));
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));

 	if (otg_mode_host)
 		mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
 	else {
 		initialize_otg_port(NULL);
 		mxc_register_device(&mxc_usbdr_udc_device, &usb_pdata);
 	}

 	gpio_request(USBH1_RST, "usb_rst");
 	gpio_direction_output(USBH1_RST, 0);
 	msleep(20);
 	gpio_set_value(USBH1_RST, 1);
 	mxc_register_device(&mxc_usbh1_device, &usbh1_config);

 #ifdef CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD
 	eukrea_mbimxsd51_baseboard_init();
 #endif
 }

 static void __init eukrea_cpuimx51sd_timer_init(void)
 {
 	mx51_clocks_init(32768, 24000000, 22579200, 0);
 }

 static struct sys_timer mxc_timer = {
 	.init	= eukrea_cpuimx51sd_timer_init,
 };

 MACHINE_START(EUKREA_CPUIMX51SD, "Eukrea CPUIMX51SD")
 	/* Maintainer: Eric Bénard <eric@eukrea.com> */
 	.boot_params = MX51_PHYS_OFFSET + 0x100,
 	.map_io = mx51_map_io,
 	.init_early = imx51_init_early,
 	.init_irq = mx51_init_irq,
 	.timer = &mxc_timer,
 	.init_machine = eukrea_cpuimx51sd_init,
 MACHINE_END
	/*
	*
	* Copyright (C) 2010 Eric Bénard <eric@eukrea.com>
	*
	* based on board-mx51_babbage.c which is
	* Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
	* Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
	*
	* The code contained herein is licensed under the GNU General Public
	* License. You may obtain a copy of the GNU General Public License
	* Version 2 or later at the following locations:
	*
	* http://www.opensource.org/licenses/gpl-license.html
	* http://www.gnu.org/copyleft/gpl.html
	*/

	#include <linux/init.h>
	#include <linux/platform_device.h>
	#include <linux/i2c.h>
	#include <linux/i2c/tsc2007.h>
	#include <linux/gpio.h>
	#include <linux/delay.h>
	#include <linux/io.h>
	#include <linux/interrupt.h>
	#include <linux/irq.h>
	#include <linux/i2c-gpio.h>
	#include <linux/spi/spi.h>
	#include <linux/can/platform/mcp251x.h>

	#include <mach/eukrea-baseboards.h>
	#include <mach/common.h>
	#include <mach/hardware.h>
	#include <mach/iomux-mx51.h>

	#include <asm/irq.h>
	#include <asm/setup.h>
	#include <asm/mach-types.h>
	#include <asm/mach/arch.h>
	#include <asm/mach/time.h>

	#include "devices-imx51.h"
	#include "devices.h"
	#include "cpu_op-mx51.h"

	#define USBH1_RST IMX_GPIO_NR(2, 28)
	#define ETH_RST IMX_GPIO_NR(2, 31)
	#define TSC2007_IRQGPIO IMX_GPIO_NR(3, 12)
	#define CAN_IRQGPIO IMX_GPIO_NR(1, 1)
	#define CAN_RST IMX_GPIO_NR(4, 15)
	#define CAN_NCS IMX_GPIO_NR(4, 24)
	#define CAN_RXOBF IMX_GPIO_NR(1, 4)
	#define CAN_RX1BF IMX_GPIO_NR(1, 6)
	#define CAN_TXORTS IMX_GPIO_NR(1, 7)
	#define CAN_TX1RTS IMX_GPIO_NR(1, 8)
	#define CAN_TX2RTS IMX_GPIO_NR(1, 9)
	#define I2C_SCL IMX_GPIO_NR(4, 16)
	#define I2C_SDA IMX_GPIO_NR(4, 17)

	/* USB_CTRL_1 */
	#define MX51_USB_CTRL_1_OFFSET 0x10
	#define MX51_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)

	#define MX51_USB_PLLDIV_12_MHZ 0x00
	#define MX51_USB_PLL_DIV_19_2_MHZ 0x01
	#define MX51_USB_PLL_DIV_24_MHZ 0x02

	static iomux_v3_cfg_t eukrea_cpuimx51sd_pads[] = {
	/* UART1 */
	MX51_PAD_UART1_RXD__UART1_RXD,
	MX51_PAD_UART1_TXD__UART1_TXD,
	MX51_PAD_UART1_RTS__UART1_RTS,
	MX51_PAD_UART1_CTS__UART1_CTS,

	/* USB HOST1 */
	MX51_PAD_USBH1_CLK__USBH1_CLK,
	MX51_PAD_USBH1_DIR__USBH1_DIR,
	MX51_PAD_USBH1_NXT__USBH1_NXT,
	MX51_PAD_USBH1_DATA0__USBH1_DATA0,
	MX51_PAD_USBH1_DATA1__USBH1_DATA1,
	MX51_PAD_USBH1_DATA2__USBH1_DATA2,
	MX51_PAD_USBH1_DATA3__USBH1_DATA3,
	MX51_PAD_USBH1_DATA4__USBH1_DATA4,
	MX51_PAD_USBH1_DATA5__USBH1_DATA5,
	MX51_PAD_USBH1_DATA6__USBH1_DATA6,
	MX51_PAD_USBH1_DATA7__USBH1_DATA7,
	MX51_PAD_USBH1_STP__USBH1_STP,
	MX51_PAD_EIM_CS3__GPIO2_28, /* PHY nRESET */

	/* FEC */
	MX51_PAD_EIM_DTACK__GPIO2_31, /* PHY nRESET */

	/* HSI2C */
	MX51_PAD_I2C1_CLK__GPIO4_16,
	MX51_PAD_I2C1_DAT__GPIO4_17,

	/* CAN */
	MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
	MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
	MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
	MX51_PAD_CSPI1_SS0__GPIO4_24, /* nCS */
	MX51_PAD_CSI2_PIXCLK__GPIO4_15, /* nReset */
	MX51_PAD_GPIO1_1__GPIO1_1, /* IRQ */
	MX51_PAD_GPIO1_4__GPIO1_4, /* Control signals */
	MX51_PAD_GPIO1_6__GPIO1_6,
	MX51_PAD_GPIO1_7__GPIO1_7,
	MX51_PAD_GPIO1_8__GPIO1_8,
	MX51_PAD_GPIO1_9__GPIO1_9,

	/* Touchscreen */
	/* IRQ */
	NEW_PAD_CTRL(MX51_PAD_GPIO_NAND__GPIO_NAND, PAD_CTL_PUS_22K_UP \|
	PAD_CTL_PKE \| PAD_CTL_SRE_FAST \|
	PAD_CTL_DSE_HIGH \| PAD_CTL_PUE \| PAD_CTL_HYS),
	};

	static const struct imxuart_platform_data uart_pdata __initconst = {
	.flags = IMXUART_HAVE_RTSCTS,
	};

	static struct tsc2007_platform_data tsc2007_info = {
	.model = 2007,
	.x_plate_ohms = 180,
	};

	static struct i2c_board_info eukrea_cpuimx51sd_i2c_devices[] = {
	{
	I2C_BOARD_INFO("pcf8563", 0x51),
	}, {
	I2C_BOARD_INFO("tsc2007", 0x49),
	.type = "tsc2007",
	.platform_data = &tsc2007_info,
	.irq = gpio_to_irq(TSC2007_IRQGPIO),
	},
	};

	static const struct mxc_nand_platform_data
	eukrea_cpuimx51sd_nand_board_info __initconst = {
	.width = 1,
	.hw_ecc = 1,
	.flash_bbt = 1,
	};

	/* This function is board specific as the bit mask for the plldiv will also
	be different for other Freescale SoCs, thus a common bitmask is not
	possible and cannot get place in /plat-mxc/ehci.c.*/
	static int initialize_otg_port(struct platform_device *pdev)
	{
	u32 v;
	void __iomem *usb_base;
	void __iomem *usbother_base;

	usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
	if (!usb_base)
	return -ENOMEM;
	usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;

	/* Set the PHY clock to 19.2MHz */
	v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
	v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
	v \|= MX51_USB_PLL_DIV_19_2_MHZ;
	__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
	iounmap(usb_base);

	mdelay(10);

	return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
	}

	static int initialize_usbh1_port(struct platform_device *pdev)
	{
	u32 v;
	void __iomem *usb_base;
	void __iomem *usbother_base;

	usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
	if (!usb_base)
	return -ENOMEM;
	usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;

	/* The clock for the USBH1 ULPI port will come from the PHY. */
	v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
	__raw_writel(v \| MX51_USB_CTRL_UH1_EXT_CLK_EN,
	usbother_base + MX51_USB_CTRL_1_OFFSET);
	iounmap(usb_base);

	mdelay(10);

	return mx51_initialize_usb_hw(1, MXC_EHCI_POWER_PINS_ENABLED \|
	MXC_EHCI_ITC_NO_THRESHOLD);
	}

	static struct mxc_usbh_platform_data dr_utmi_config = {
	.init = initialize_otg_port,
	.portsc = MXC_EHCI_UTMI_16BIT,
	};

	static struct fsl_usb2_platform_data usb_pdata = {
	.operating_mode = FSL_USB2_DR_DEVICE,
	.phy_mode = FSL_USB2_PHY_UTMI_WIDE,
	};

	static struct mxc_usbh_platform_data usbh1_config = {
	.init = initialize_usbh1_port,
	.portsc = MXC_EHCI_MODE_ULPI,
	};

	static int otg_mode_host;

	static int __init eukrea_cpuimx51sd_otg_mode(char *options)
	{
	if (!strcmp(options, "host"))
	otg_mode_host = 1;
	else if (!strcmp(options, "device"))
	otg_mode_host = 0;
	else
	pr_info("otg_mode neither \"host\" nor \"device\". "
	"Defaulting to device\n");
	return 0;
	}
	__setup("otg_mode=", eukrea_cpuimx51sd_otg_mode);

	static struct i2c_gpio_platform_data pdata = {
	.sda_pin = I2C_SDA,
	.sda_is_open_drain = 0,
	.scl_pin = I2C_SCL,
	.scl_is_open_drain = 0,
	.udelay = 2,
	};

	static struct platform_device hsi2c_gpio_device = {
	.name = "i2c-gpio",
	.id = 0,
	.dev.platform_data = &pdata,
	};

	static struct mcp251x_platform_data mcp251x_info = {
	.oscillator_frequency = 24E6,
	};

	static struct spi_board_info cpuimx51sd_spi_device[] = {
	{
	.modalias = "mcp2515",
	.max_speed_hz = 10000000,
	.bus_num = 0,
	.mode = SPI_MODE_0,
	.chip_select = 0,
	.platform_data = &mcp251x_info,
	.irq = gpio_to_irq(CAN_IRQGPIO)
	},
	};

	static int cpuimx51sd_spi1_cs[] = {
	CAN_NCS,
	};

	static const struct spi_imx_master cpuimx51sd_ecspi1_pdata __initconst = {
	.chipselect = cpuimx51sd_spi1_cs,
	.num_chipselect = ARRAY_SIZE(cpuimx51sd_spi1_cs),
	};

	static struct platform_device *platform_devices[] __initdata = {
	&hsi2c_gpio_device,
	};

	static void __init eukrea_cpuimx51sd_init(void)
	{
	imx51_soc_init();

	mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51sd_pads,
	ARRAY_SIZE(eukrea_cpuimx51sd_pads));

	#if defined(CONFIG_CPU_FREQ_IMX)
	get_cpu_op = mx51_get_cpu_op;
	#endif

	imx51_add_imx_uart(0, &uart_pdata);
	imx51_add_mxc_nand(&eukrea_cpuimx51sd_nand_board_info);

	gpio_request(ETH_RST, "eth_rst");
	gpio_set_value(ETH_RST, 1);
	imx51_add_fec(NULL);

	gpio_request(CAN_IRQGPIO, "can_irq");
	gpio_direction_input(CAN_IRQGPIO);
	gpio_free(CAN_IRQGPIO);
	gpio_request(CAN_NCS, "can_ncs");
	gpio_direction_output(CAN_NCS, 1);
	gpio_free(CAN_NCS);
	gpio_request(CAN_RST, "can_rst");
	gpio_direction_output(CAN_RST, 0);
	msleep(20);
	gpio_set_value(CAN_RST, 1);
	imx51_add_ecspi(0, &cpuimx51sd_ecspi1_pdata);
	spi_register_board_info(cpuimx51sd_spi_device,
	ARRAY_SIZE(cpuimx51sd_spi_device));

	gpio_request(TSC2007_IRQGPIO, "tsc2007_irq");
	gpio_direction_input(TSC2007_IRQGPIO);
	gpio_free(TSC2007_IRQGPIO);

	i2c_register_board_info(0, eukrea_cpuimx51sd_i2c_devices,
	ARRAY_SIZE(eukrea_cpuimx51sd_i2c_devices));
	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));

	if (otg_mode_host)
	mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
	else {
	initialize_otg_port(NULL);
	mxc_register_device(&mxc_usbdr_udc_device, &usb_pdata);
	}

	gpio_request(USBH1_RST, "usb_rst");
	gpio_direction_output(USBH1_RST, 0);
	msleep(20);
	gpio_set_value(USBH1_RST, 1);
	mxc_register_device(&mxc_usbh1_device, &usbh1_config);

	#ifdef CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD
	eukrea_mbimxsd51_baseboard_init();
	#endif
	}

	static void __init eukrea_cpuimx51sd_timer_init(void)
	{
	mx51_clocks_init(32768, 24000000, 22579200, 0);
	}

	static struct sys_timer mxc_timer = {
	.init = eukrea_cpuimx51sd_timer_init,
	};

	MACHINE_START(EUKREA_CPUIMX51SD, "Eukrea CPUIMX51SD")
	/* Maintainer: Eric Bénard <eric@eukrea.com> */
	.boot_params = MX51_PHYS_OFFSET + 0x100,
	.map_io = mx51_map_io,
	.init_early = imx51_init_early,
	.init_irq = mx51_init_irq,
	.timer = &mxc_timer,
	.init_machine = eukrea_cpuimx51sd_init,
	MACHINE_END