diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
index f2455c5..120bc49 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
@@ -11,6 +11,10 @@
       0 = active high
       1 = active low
 
+Optional properties:
+- little-endian : GPIO registers are used as little endian. If not
+                  present registers are used as big endian by default.
+
 Example:
 
 gpio0: gpio@1100 {
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index ad6de73..e74df32 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -184,6 +184,7 @@
 							regulator-name = "VDD_SDHC_1V8";
 							regulator-min-microvolt = <1800000>;
 							regulator-max-microvolt = <1800000>;
+							regulator-always-on;
 						};
 					};
 				};
diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi
index 8ea177f..fb1da99 100644
--- a/arch/arm/boot/dts/berlin2q.dtsi
+++ b/arch/arm/boot/dts/berlin2q.dtsi
@@ -118,7 +118,8 @@
 		sdhci0: sdhci@ab0000 {
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab0000 0x200>;
-			clocks = <&chip_clk CLKID_SDIO1XIN>;
+			clocks = <&chip_clk CLKID_SDIO1XIN>, <&chip_clk CLKID_SDIO>;
+			clock-names = "io", "core";
 			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
@@ -126,7 +127,8 @@
 		sdhci1: sdhci@ab0800 {
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab0800 0x200>;
-			clocks = <&chip_clk CLKID_SDIO1XIN>;
+			clocks = <&chip_clk CLKID_SDIO1XIN>, <&chip_clk CLKID_SDIO>;
+			clock-names = "io", "core";
 			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
@@ -135,7 +137,7 @@
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab1000 0x200>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&chip_clk CLKID_NFC_ECC>, <&chip_clk CLKID_NFC>;
+			clocks = <&chip_clk CLKID_NFC_ECC>, <&chip_clk CLKID_SDIO>;
 			clock-names = "io", "core";
 			status = "disabled";
 		};
diff --git a/arch/arm/boot/dts/imx6q-gw5400-a.dts b/arch/arm/boot/dts/imx6q-gw5400-a.dts
index 58adf17..a51834e 100644
--- a/arch/arm/boot/dts/imx6q-gw5400-a.dts
+++ b/arch/arm/boot/dts/imx6q-gw5400-a.dts
@@ -154,7 +154,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
index 7b31fdb..dc0cebf 100644
--- a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
@@ -94,7 +94,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
index 1b66328..18cd411 100644
--- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
@@ -154,7 +154,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
index 7c51839..eea90f3 100644
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
@@ -155,7 +155,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
index 929e0b3..6c11a2a 100644
--- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
@@ -145,7 +145,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 8263fc1..d354d40 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -113,14 +113,14 @@
 &clks {
 	assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
 			  <&clks IMX6QDL_PLL4_BYPASS>,
-			  <&clks IMX6QDL_CLK_PLL4_POST_DIV>,
 			  <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
+			  <&clks IMX6QDL_CLK_PLL4_POST_DIV>;
 	assigned-clock-parents = <&clks IMX6QDL_CLK_LVDS2_IN>,
 				 <&clks IMX6QDL_PLL4_BYPASS_SRC>,
 				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
 				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-	assigned-clock-rates = <0>, <0>, <24576000>;
+	assigned-clock-rates = <0>, <0>, <0>, <0>, <24576000>;
 };
 
 &ecspi1 {
diff --git a/arch/arm/boot/dts/sun6i-a31s-primo81.dts b/arch/arm/boot/dts/sun6i-a31s-primo81.dts
index 2d4250b..68b479b 100644
--- a/arch/arm/boot/dts/sun6i-a31s-primo81.dts
+++ b/arch/arm/boot/dts/sun6i-a31s-primo81.dts
@@ -83,6 +83,7 @@
 		reg = <0x5d>;
 		interrupt-parent = <&pio>;
 		interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>; /* PA3 */
+		touchscreen-swapped-x-y;
 	};
 };
 
diff --git a/arch/arm/boot/dts/vf610-colibri.dtsi b/arch/arm/boot/dts/vf610-colibri.dtsi
index 19fe045..2d7eab7 100644
--- a/arch/arm/boot/dts/vf610-colibri.dtsi
+++ b/arch/arm/boot/dts/vf610-colibri.dtsi
@@ -18,8 +18,3 @@
 		reg = <0x80000000 0x10000000>;
 	};
 };
-
-&L2 {
-	arm,data-latency = <2 1 2>;
-	arm,tag-latency = <3 2 3>;
-};
diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/vf610.dtsi
index 5f8eb1b..58bc6e4 100644
--- a/arch/arm/boot/dts/vf610.dtsi
+++ b/arch/arm/boot/dts/vf610.dtsi
@@ -19,7 +19,7 @@
 		reg = <0x40006000 0x1000>;
 		cache-unified;
 		cache-level = <2>;
-		arm,data-latency = <1 1 1>;
+		arm,data-latency = <3 3 3>;
 		arm,tag-latency = <2 2 2>;
 	};
 };
diff --git a/arch/arm/boot/dts/vfxxx.dtsi b/arch/arm/boot/dts/vfxxx.dtsi
index 0d5acc2..3cd1b27 100644
--- a/arch/arm/boot/dts/vfxxx.dtsi
+++ b/arch/arm/boot/dts/vfxxx.dtsi
@@ -178,8 +178,10 @@
 				compatible = "fsl,vf610-sai";
 				reg = <0x40031000 0x1000>;
 				interrupts = <86 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clks VF610_CLK_SAI2>;
-				clock-names = "sai";
+				clocks = <&clks VF610_CLK_SAI2>,
+					<&clks VF610_CLK_SAI2_DIV>,
+					<&clks 0>, <&clks 0>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
 				dma-names = "tx", "rx";
 				dmas = <&edma0 0 21>,
 					<&edma0 0 20>;
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 9267300..28656c2 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -4,7 +4,6 @@
 	select ARCH_REQUIRE_GPIOLIB
 	select COMMON_CLK_AT91
 	select PINCTRL
-	select PINCTRL_AT91
 	select SOC_BUS
 
 if ARCH_AT91
@@ -17,6 +16,7 @@
 	select HAVE_AT91_USB_CLK
 	select HAVE_AT91_H32MX
 	select HAVE_AT91_GENERATED_CLK
+	select PINCTRL_AT91PIO4
 	help
 	  Select this if ou are using one of Atmel's SAMA5D2 family SoC.
 
@@ -27,6 +27,7 @@
 	select HAVE_AT91_UTMI
 	select HAVE_AT91_SMD
 	select HAVE_AT91_USB_CLK
+	select PINCTRL_AT91
 	help
 	  Select this if you are using one of Atmel's SAMA5D3 family SoC.
 	  This support covers SAMA5D31, SAMA5D33, SAMA5D34, SAMA5D35, SAMA5D36.
@@ -40,6 +41,7 @@
 	select HAVE_AT91_SMD
 	select HAVE_AT91_USB_CLK
 	select HAVE_AT91_H32MX
+	select PINCTRL_AT91
 	help
 	  Select this if you are using one of Atmel's SAMA5D4 family SoC.
 
@@ -50,6 +52,7 @@
 	select CPU_ARM920T
 	select HAVE_AT91_USB_CLK
 	select MIGHT_HAVE_PCI
+	select PINCTRL_AT91
 	select SOC_SAM_V4_V5
 	select SRAM if PM
 	help
@@ -65,6 +68,7 @@
 	select HAVE_AT91_UTMI
 	select HAVE_FB_ATMEL
 	select MEMORY
+	select PINCTRL_AT91
 	select SOC_SAM_V4_V5
 	select SRAM if PM
 	help
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index 80e277c..23726fb 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -41,8 +41,10 @@
  * implementation should be moved down into the pinctrl driver and get
  * called as part of the generic suspend/resume path.
  */
+#ifdef CONFIG_PINCTRL_AT91
 extern void at91_pinctrl_gpio_suspend(void);
 extern void at91_pinctrl_gpio_resume(void);
+#endif
 
 static struct {
 	unsigned long uhp_udp_mask;
@@ -151,8 +153,9 @@
 
 static int at91_pm_enter(suspend_state_t state)
 {
+#ifdef CONFIG_PINCTRL_AT91
 	at91_pinctrl_gpio_suspend();
-
+#endif
 	switch (state) {
 	/*
 	 * Suspend-to-RAM is like STANDBY plus slow clock mode, so
@@ -192,7 +195,9 @@
 error:
 	target_state = PM_SUSPEND_ON;
 
+#ifdef CONFIG_PINCTRL_AT91
 	at91_pinctrl_gpio_resume();
+#endif
 	return 0;
 }
 
diff --git a/arch/arm/mach-exynos/pmu.c b/arch/arm/mach-exynos/pmu.c
index de68938..c21e41d 100644
--- a/arch/arm/mach-exynos/pmu.c
+++ b/arch/arm/mach-exynos/pmu.c
@@ -748,8 +748,12 @@
 void exynos_sys_powerdown_conf(enum sys_powerdown mode)
 {
 	unsigned int i;
+	const struct exynos_pmu_data *pmu_data;
 
-	const struct exynos_pmu_data *pmu_data = pmu_context->pmu_data;
+	if (!pmu_context)
+		return;
+
+	pmu_data = pmu_context->pmu_data;
 
 	if (pmu_data->powerdown_conf)
 		pmu_data->powerdown_conf(mode);
diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h
index b024390..7a0c13b 100644
--- a/arch/arm/mach-ixp4xx/include/mach/io.h
+++ b/arch/arm/mach-ixp4xx/include/mach/io.h
@@ -143,7 +143,7 @@
 		writel(*vaddr++, bus_addr);
 }
 
-static inline unsigned char __indirect_readb(const volatile void __iomem *p)
+static inline u8 __indirect_readb(const volatile void __iomem *p)
 {
 	u32 addr = (u32)p;
 	u32 n, byte_enables, data;
@@ -166,7 +166,7 @@
 		*vaddr++ = readb(bus_addr);
 }
 
-static inline unsigned short __indirect_readw(const volatile void __iomem *p)
+static inline u16 __indirect_readw(const volatile void __iomem *p)
 {
 	u32 addr = (u32)p;
 	u32 n, byte_enables, data;
@@ -189,7 +189,7 @@
 		*vaddr++ = readw(bus_addr);
 }
 
-static inline unsigned long __indirect_readl(const volatile void __iomem *p)
+static inline u32 __indirect_readl(const volatile void __iomem *p)
 {
 	u32 addr = (__force u32)p;
 	u32 data;
@@ -350,7 +350,7 @@
 					((unsigned long)p <= (PIO_MASK + PIO_OFFSET)))
 
 #define	ioread8(p)			ioread8(p)
-static inline unsigned int ioread8(const void __iomem *addr)
+static inline u8 ioread8(const void __iomem *addr)
 {
 	unsigned long port = (unsigned long __force)addr;
 	if (__is_io_address(port))
@@ -378,7 +378,7 @@
 }
 
 #define	ioread16(p)			ioread16(p)
-static inline unsigned int ioread16(const void __iomem *addr)
+static inline u16 ioread16(const void __iomem *addr)
 {
 	unsigned long port = (unsigned long __force)addr;
 	if (__is_io_address(port))
@@ -407,7 +407,7 @@
 }
 
 #define	ioread32(p)			ioread32(p)
-static inline unsigned int ioread32(const void __iomem *addr)
+static inline u32 ioread32(const void __iomem *addr)
 {
 	unsigned long port = (unsigned long __force)addr;
 	if (__is_io_address(port))
diff --git a/arch/arm/mach-pxa/ezx.c b/arch/arm/mach-pxa/ezx.c
index 9a9c15b..7c0d561 100644
--- a/arch/arm/mach-pxa/ezx.c
+++ b/arch/arm/mach-pxa/ezx.c
@@ -889,6 +889,7 @@
 
 	pxa_set_keypad_info(&e680_keypad_platform_data);
 
+	pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
 	platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
 	platform_add_devices(ARRAY_AND_SIZE(e680_devices));
 }
@@ -956,6 +957,7 @@
 
 	pxa_set_keypad_info(&a1200_keypad_platform_data);
 
+	pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
 	platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
 	platform_add_devices(ARRAY_AND_SIZE(a1200_devices));
 }
@@ -1148,6 +1150,7 @@
 		platform_device_register(&a910_camera);
 	}
 
+	pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
 	platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
 	platform_add_devices(ARRAY_AND_SIZE(a910_devices));
 }
@@ -1215,6 +1218,7 @@
 
 	pxa_set_keypad_info(&e6_keypad_platform_data);
 
+	pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
 	platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
 	platform_add_devices(ARRAY_AND_SIZE(e6_devices));
 }
@@ -1256,6 +1260,7 @@
 
 	pxa_set_keypad_info(&e2_keypad_platform_data);
 
+	pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
 	platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
 	platform_add_devices(ARRAY_AND_SIZE(e2_devices));
 }
diff --git a/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c b/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c
index a19460e..b355fca 100644
--- a/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c
+++ b/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c
@@ -20,7 +20,7 @@
 #include <plat/cpu.h>
 #include <plat/cpu-freq-core.h>
 
-static struct cpufreq_frequency_table s3c2440_plls_12[] __initdata = {
+static struct cpufreq_frequency_table s3c2440_plls_12[] = {
 	{ .frequency = 75000000,	.driver_data = PLLVAL(0x75, 3, 3),  }, 	/* FVco 600.000000 */
 	{ .frequency = 80000000,	.driver_data = PLLVAL(0x98, 4, 3),  }, 	/* FVco 640.000000 */
 	{ .frequency = 90000000,	.driver_data = PLLVAL(0x70, 2, 3),  }, 	/* FVco 720.000000 */
diff --git a/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c b/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c
index 1191b29..be9a248 100644
--- a/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c
+++ b/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c
@@ -20,7 +20,7 @@
 #include <plat/cpu.h>
 #include <plat/cpu-freq-core.h>
 
-static struct cpufreq_frequency_table s3c2440_plls_169344[] __initdata = {
+static struct cpufreq_frequency_table s3c2440_plls_169344[] = {
 	{ .frequency = 78019200,	.driver_data = PLLVAL(121, 5, 3), 	}, 	/* FVco 624.153600 */
 	{ .frequency = 84067200,	.driver_data = PLLVAL(131, 5, 3), 	}, 	/* FVco 672.537600 */
 	{ .frequency = 90115200,	.driver_data = PLLVAL(141, 5, 3), 	}, 	/* FVco 720.921600 */
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
index e81cd48..925552e 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
@@ -269,6 +269,7 @@
 			clock-frequency = <0>;	/* Updated by bootloader */
 			voltage-ranges = <1800 1800 3300 3300>;
 			sdhci,auto-cmd12;
+			little-endian;
 			bus-width = <4>;
 		};
 
@@ -277,6 +278,7 @@
 			reg = <0x0 0x2300000 0x0 0x10000>;
 			interrupts = <0 36 0x4>; /* Level high type */
 			gpio-controller;
+			little-endian;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -287,6 +289,7 @@
 			reg = <0x0 0x2310000 0x0 0x10000>;
 			interrupts = <0 36 0x4>; /* Level high type */
 			gpio-controller;
+			little-endian;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -297,6 +300,7 @@
 			reg = <0x0 0x2320000 0x0 0x10000>;
 			interrupts = <0 37 0x4>; /* Level high type */
 			gpio-controller;
+			little-endian;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -307,6 +311,7 @@
 			reg = <0x0 0x2330000 0x0 0x10000>;
 			interrupts = <0 37 0x4>; /* Level high type */
 			gpio-controller;
+			little-endian;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/drivers/bus/sunxi-rsb.c b/drivers/bus/sunxi-rsb.c
index 846bc29..25996e2 100644
--- a/drivers/bus/sunxi-rsb.c
+++ b/drivers/bus/sunxi-rsb.c
@@ -342,13 +342,13 @@
 
 	ret = _sunxi_rsb_run_xfer(rsb);
 	if (ret)
-		goto out;
+		goto unlock;
 
 	*buf = readl(rsb->regs + RSB_DATA);
 
+unlock:
 	mutex_unlock(&rsb->lock);
 
-out:
 	return ret;
 }
 
@@ -527,9 +527,9 @@
  */
 
 static const struct sunxi_rsb_addr_map sunxi_rsb_addr_maps[] = {
-	{ 0x3e3, 0x2d }, /* Primary PMIC: AXP223, AXP809, AXP81X, ... */
+	{ 0x3a3, 0x2d }, /* Primary PMIC: AXP223, AXP809, AXP81X, ... */
 	{ 0x745, 0x3a }, /* Secondary PMIC: AXP806, ... */
-	{ 0xe89, 0x45 }, /* Peripheral IC: AC100, ... */
+	{ 0xe89, 0x4e }, /* Peripheral IC: AC100, ... */
 };
 
 static u8 sunxi_rsb_get_rtaddr(u16 hwaddr)
diff --git a/drivers/clk/imx/clk-vf610.c b/drivers/clk/imx/clk-vf610.c
index d1b1c95..0a94d96 100644
--- a/drivers/clk/imx/clk-vf610.c
+++ b/drivers/clk/imx/clk-vf610.c
@@ -335,22 +335,22 @@
 	clk[VF610_CLK_SAI0_SEL] = imx_clk_mux("sai0_sel", CCM_CSCMR1, 0, 2, sai_sels, 4);
 	clk[VF610_CLK_SAI0_EN] = imx_clk_gate("sai0_en", "sai0_sel", CCM_CSCDR1, 16);
 	clk[VF610_CLK_SAI0_DIV] = imx_clk_divider("sai0_div", "sai0_en", CCM_CSCDR1, 0, 4);
-	clk[VF610_CLK_SAI0] = imx_clk_gate2("sai0", "sai0_div", CCM_CCGR0, CCM_CCGRx_CGn(15));
+	clk[VF610_CLK_SAI0] = imx_clk_gate2("sai0", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(15));
 
 	clk[VF610_CLK_SAI1_SEL] = imx_clk_mux("sai1_sel", CCM_CSCMR1, 2, 2, sai_sels, 4);
 	clk[VF610_CLK_SAI1_EN] = imx_clk_gate("sai1_en", "sai1_sel", CCM_CSCDR1, 17);
 	clk[VF610_CLK_SAI1_DIV] = imx_clk_divider("sai1_div", "sai1_en", CCM_CSCDR1, 4, 4);
-	clk[VF610_CLK_SAI1] = imx_clk_gate2("sai1", "sai1_div", CCM_CCGR1, CCM_CCGRx_CGn(0));
+	clk[VF610_CLK_SAI1] = imx_clk_gate2("sai1", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(0));
 
 	clk[VF610_CLK_SAI2_SEL] = imx_clk_mux("sai2_sel", CCM_CSCMR1, 4, 2, sai_sels, 4);
 	clk[VF610_CLK_SAI2_EN] = imx_clk_gate("sai2_en", "sai2_sel", CCM_CSCDR1, 18);
 	clk[VF610_CLK_SAI2_DIV] = imx_clk_divider("sai2_div", "sai2_en", CCM_CSCDR1, 8, 4);
-	clk[VF610_CLK_SAI2] = imx_clk_gate2("sai2", "sai2_div", CCM_CCGR1, CCM_CCGRx_CGn(1));
+	clk[VF610_CLK_SAI2] = imx_clk_gate2("sai2", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(1));
 
 	clk[VF610_CLK_SAI3_SEL] = imx_clk_mux("sai3_sel", CCM_CSCMR1, 6, 2, sai_sels, 4);
 	clk[VF610_CLK_SAI3_EN] = imx_clk_gate("sai3_en", "sai3_sel", CCM_CSCDR1, 19);
 	clk[VF610_CLK_SAI3_DIV] = imx_clk_divider("sai3_div", "sai3_en", CCM_CSCDR1, 12, 4);
-	clk[VF610_CLK_SAI3] = imx_clk_gate2("sai3", "sai3_div", CCM_CCGR1, CCM_CCGRx_CGn(2));
+	clk[VF610_CLK_SAI3] = imx_clk_gate2("sai3", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(2));
 
 	clk[VF610_CLK_NFC_SEL] = imx_clk_mux("nfc_sel", CCM_CSCMR1, 12, 2, nfc_sels, 4);
 	clk[VF610_CLK_NFC_EN] = imx_clk_gate("nfc_en", "nfc_sel", CCM_CSCDR2, 9);
diff --git a/drivers/cpufreq/s3c24xx-cpufreq.c b/drivers/cpufreq/s3c24xx-cpufreq.c
index 733aa51..68ef8fd 100644
--- a/drivers/cpufreq/s3c24xx-cpufreq.c
+++ b/drivers/cpufreq/s3c24xx-cpufreq.c
@@ -648,7 +648,7 @@
  *
  * Register the given set of PLLs with the system.
  */
-int __init s3c_plltab_register(struct cpufreq_frequency_table *plls,
+int s3c_plltab_register(struct cpufreq_frequency_table *plls,
 			       unsigned int plls_no)
 {
 	struct cpufreq_frequency_table *vals;
diff --git a/drivers/irqchip/irq-versatile-fpga.c b/drivers/irqchip/irq-versatile-fpga.c
index 598ab3f..cadf104 100644
--- a/drivers/irqchip/irq-versatile-fpga.c
+++ b/drivers/irqchip/irq-versatile-fpga.c
@@ -210,7 +210,12 @@
 		parent_irq = -1;
 	}
 
+#ifdef CONFIG_ARCH_VERSATILE
+	fpga_irq_init(base, node->name, IRQ_SIC_START, parent_irq, valid_mask,
+				  node);
+#else
 	fpga_irq_init(base, node->name, 0, parent_irq, valid_mask, node);
+#endif
 
 	writel(clear_mask, base + IRQ_ENABLE_CLEAR);
 	writel(clear_mask, base + FIQ_ENABLE_CLEAR);
diff --git a/drivers/memory/fsl_ifc.c b/drivers/memory/fsl_ifc.c
index e87459f..acd1460 100644
--- a/drivers/memory/fsl_ifc.c
+++ b/drivers/memory/fsl_ifc.c
@@ -22,6 +22,7 @@
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/compiler.h>
+#include <linux/sched.h>
 #include <linux/spinlock.h>
 #include <linux/types.h>
 #include <linux/slab.h>