bnx2x: Remove 100Mb force speed for BCM84833
Remove unsupported speed of 100Mb force for BCM84833 due to hardware
limitation.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
index a688b9d97..f99c6e3 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
@@ -365,13 +365,18 @@
DP(NETIF_MSG_LINK, "cfg_idx = %x\n", cfg_idx);
if (cmd->autoneg == AUTONEG_ENABLE) {
+ u32 an_supported_speed = bp->port.supported[cfg_idx];
+ if (bp->link_params.phy[EXT_PHY1].type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833)
+ an_supported_speed |= (SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full);
if (!(bp->port.supported[cfg_idx] & SUPPORTED_Autoneg)) {
DP(NETIF_MSG_LINK, "Autoneg not supported\n");
return -EINVAL;
}
/* advertise the requested speed and duplex if supported */
- if (cmd->advertising & ~(bp->port.supported[cfg_idx])) {
+ if (cmd->advertising & ~an_supported_speed) {
DP(NETIF_MSG_LINK, "Advertisement parameters "
"are not supported\n");
return -EINVAL;
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
index cc80637..1d1a809 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
@@ -9454,13 +9454,10 @@
an_1000_val);
/* set 100 speed advertisement */
- if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
+ if ((phy->req_line_speed == SPEED_AUTO_NEG) &&
(phy->speed_cap_mask &
(PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL |
- PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF)) &&
- (phy->supported &
- (SUPPORTED_100baseT_Half |
- SUPPORTED_100baseT_Full)))) {
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF))) {
an_10_100_val |= (1<<7);
/* Enable autoneg and restart autoneg for legacy speeds */
autoneg_val |= (1<<9 | 1<<12);
@@ -11528,6 +11525,19 @@
}
phy->mdio_ctrl = bnx2x_get_emac_base(bp, mdc_mdio_access, port);
+ if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) &&
+ (phy->ver_addr)) {
+ /*
+ * Remove 100Mb link supported for BCM84833 when phy fw
+ * version lower than or equal to 1.39
+ */
+ u32 raw_ver = REG_RD(bp, phy->ver_addr);
+ if (((raw_ver & 0x7F) <= 39) &&
+ (((raw_ver & 0xF80) >> 7) <= 1))
+ phy->supported &= ~(SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full);
+ }
+
/*
* In case mdc/mdio_access of the external phy is different than the
* mdc/mdio access of the XGXS, a HW lock must be taken in each access