| /dts-v1/; |
| |
| #include "skeleton.dtsi" |
| |
| #include <dt-bindings/clock/qcom,gcc-apq8084.h> |
| #include <dt-bindings/gpio/gpio.h> |
| |
| / { |
| model = "Qualcomm APQ 8084"; |
| compatible = "qcom,apq8084"; |
| interrupt-parent = <&intc>; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| smem_mem: smem_region@fa00000 { |
| reg = <0xfa00000 0x200000>; |
| no-map; |
| }; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu@0 { |
| device_type = "cpu"; |
| compatible = "qcom,krait"; |
| reg = <0>; |
| enable-method = "qcom,kpss-acc-v2"; |
| next-level-cache = <&L2>; |
| qcom,acc = <&acc0>; |
| qcom,saw = <&saw0>; |
| cpu-idle-states = <&CPU_SPC>; |
| }; |
| |
| cpu@1 { |
| device_type = "cpu"; |
| compatible = "qcom,krait"; |
| reg = <1>; |
| enable-method = "qcom,kpss-acc-v2"; |
| next-level-cache = <&L2>; |
| qcom,acc = <&acc1>; |
| qcom,saw = <&saw1>; |
| cpu-idle-states = <&CPU_SPC>; |
| }; |
| |
| cpu@2 { |
| device_type = "cpu"; |
| compatible = "qcom,krait"; |
| reg = <2>; |
| enable-method = "qcom,kpss-acc-v2"; |
| next-level-cache = <&L2>; |
| qcom,acc = <&acc2>; |
| qcom,saw = <&saw2>; |
| cpu-idle-states = <&CPU_SPC>; |
| }; |
| |
| cpu@3 { |
| device_type = "cpu"; |
| compatible = "qcom,krait"; |
| reg = <3>; |
| enable-method = "qcom,kpss-acc-v2"; |
| next-level-cache = <&L2>; |
| qcom,acc = <&acc3>; |
| qcom,saw = <&saw3>; |
| cpu-idle-states = <&CPU_SPC>; |
| }; |
| |
| L2: l2-cache { |
| compatible = "qcom,arch-cache"; |
| cache-level = <2>; |
| qcom,saw = <&saw_l2>; |
| }; |
| |
| idle-states { |
| CPU_SPC: spc { |
| compatible = "qcom,idle-state-spc", |
| "arm,idle-state"; |
| entry-latency-us = <150>; |
| exit-latency-us = <200>; |
| min-residency-us = <2000>; |
| }; |
| }; |
| }; |
| |
| firmware { |
| scm { |
| compatible = "qcom,scm"; |
| clocks = <&gcc GCC_CE1_CLK> , <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>; |
| clock-names = "core", "bus", "iface"; |
| }; |
| }; |
| |
| thermal-zones { |
| cpu-thermal0 { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens 5>; |
| |
| trips { |
| cpu_alert0: trip0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu_crit0: trip1 { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu-thermal1 { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens 6>; |
| |
| trips { |
| cpu_alert1: trip0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu_crit1: trip1 { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu-thermal2 { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens 7>; |
| |
| trips { |
| cpu_alert2: trip0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu_crit2: trip1 { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu-thermal3 { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens 8>; |
| |
| trips { |
| cpu_alert3: trip0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu_crit3: trip1 { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| |
| cpu-pmu { |
| compatible = "qcom,krait-pmu"; |
| interrupts = <1 7 0xf04>; |
| }; |
| |
| clocks { |
| xo_board: xo_board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <19200000>; |
| }; |
| |
| sleep_clk: sleep_clk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| interrupts = <1 2 0xf08>, |
| <1 3 0xf08>, |
| <1 4 0xf08>, |
| <1 1 0xf08>; |
| clock-frequency = <19200000>; |
| }; |
| |
| smem { |
| compatible = "qcom,smem"; |
| |
| qcom,rpm-msg-ram = <&rpm_msg_ram>; |
| memory-region = <&smem_mem>; |
| |
| hwlocks = <&tcsr_mutex 3>; |
| }; |
| |
| soc: soc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| compatible = "simple-bus"; |
| |
| intc: interrupt-controller@f9000000 { |
| compatible = "qcom,msm-qgic2"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| reg = <0xf9000000 0x1000>, |
| <0xf9002000 0x1000>; |
| }; |
| |
| apcs: syscon@f9011000 { |
| compatible = "syscon"; |
| reg = <0xf9011000 0x1000>; |
| }; |
| |
| qfprom: qfprom@fc4bc000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "qcom,qfprom"; |
| reg = <0xfc4bc000 0x1000>; |
| tsens_calib: calib@d0 { |
| reg = <0xd0 0x18>; |
| }; |
| tsens_backup: backup@440 { |
| reg = <0x440 0x10>; |
| }; |
| }; |
| |
| tsens: thermal-sensor@fc4a8000 { |
| compatible = "qcom,msm8974-tsens"; |
| reg = <0xfc4a8000 0x2000>; |
| nvmem-cells = <&tsens_calib>, <&tsens_backup>; |
| nvmem-cell-names = "calib", "calib_backup"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| timer@f9020000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| compatible = "arm,armv7-timer-mem"; |
| reg = <0xf9020000 0x1000>; |
| clock-frequency = <19200000>; |
| |
| frame@f9021000 { |
| frame-number = <0>; |
| interrupts = <0 8 0x4>, |
| <0 7 0x4>; |
| reg = <0xf9021000 0x1000>, |
| <0xf9022000 0x1000>; |
| }; |
| |
| frame@f9023000 { |
| frame-number = <1>; |
| interrupts = <0 9 0x4>; |
| reg = <0xf9023000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@f9024000 { |
| frame-number = <2>; |
| interrupts = <0 10 0x4>; |
| reg = <0xf9024000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@f9025000 { |
| frame-number = <3>; |
| interrupts = <0 11 0x4>; |
| reg = <0xf9025000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@f9026000 { |
| frame-number = <4>; |
| interrupts = <0 12 0x4>; |
| reg = <0xf9026000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@f9027000 { |
| frame-number = <5>; |
| interrupts = <0 13 0x4>; |
| reg = <0xf9027000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@f9028000 { |
| frame-number = <6>; |
| interrupts = <0 14 0x4>; |
| reg = <0xf9028000 0x1000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| saw0: power-controller@f9089000 { |
| compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; |
| reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>; |
| }; |
| |
| saw1: power-controller@f9099000 { |
| compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; |
| reg = <0xf9099000 0x1000>, <0xf9009000 0x1000>; |
| }; |
| |
| saw2: power-controller@f90a9000 { |
| compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; |
| reg = <0xf90a9000 0x1000>, <0xf9009000 0x1000>; |
| }; |
| |
| saw3: power-controller@f90b9000 { |
| compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; |
| reg = <0xf90b9000 0x1000>, <0xf9009000 0x1000>; |
| }; |
| |
| saw_l2: power-controller@f9012000 { |
| compatible = "qcom,saw2"; |
| reg = <0xf9012000 0x1000>; |
| regulator; |
| }; |
| |
| acc0: clock-controller@f9088000 { |
| compatible = "qcom,kpss-acc-v2"; |
| reg = <0xf9088000 0x1000>, |
| <0xf9008000 0x1000>; |
| }; |
| |
| acc1: clock-controller@f9098000 { |
| compatible = "qcom,kpss-acc-v2"; |
| reg = <0xf9098000 0x1000>, |
| <0xf9008000 0x1000>; |
| }; |
| |
| acc2: clock-controller@f90a8000 { |
| compatible = "qcom,kpss-acc-v2"; |
| reg = <0xf90a8000 0x1000>, |
| <0xf9008000 0x1000>; |
| }; |
| |
| acc3: clock-controller@f90b8000 { |
| compatible = "qcom,kpss-acc-v2"; |
| reg = <0xf90b8000 0x1000>, |
| <0xf9008000 0x1000>; |
| }; |
| |
| restart@fc4ab000 { |
| compatible = "qcom,pshold"; |
| reg = <0xfc4ab000 0x4>; |
| }; |
| |
| gcc: clock-controller@fc400000 { |
| compatible = "qcom,gcc-apq8084"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| reg = <0xfc400000 0x4000>; |
| }; |
| |
| tcsr_mutex_regs: syscon@fd484000 { |
| compatible = "syscon"; |
| reg = <0xfd484000 0x2000>; |
| }; |
| |
| tcsr_mutex: hwlock { |
| compatible = "qcom,tcsr-mutex"; |
| syscon = <&tcsr_mutex_regs 0 0x80>; |
| #hwlock-cells = <1>; |
| }; |
| |
| rpm_msg_ram: memory@fc428000 { |
| compatible = "qcom,rpm-msg-ram"; |
| reg = <0xfc428000 0x4000>; |
| }; |
| |
| tlmm: pinctrl@fd510000 { |
| compatible = "qcom,apq8084-pinctrl"; |
| reg = <0xfd510000 0x4000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <0 208 0>; |
| }; |
| |
| blsp2_uart2: serial@f995e000 { |
| compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; |
| reg = <0xf995e000 0x1000>; |
| interrupts = <0 114 0x0>; |
| clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| sdhci@f9824900 { |
| compatible = "qcom,sdhci-msm-v4"; |
| reg = <0xf9824900 0x11c>, <0xf9824000 0x800>; |
| reg-names = "hc_mem", "core_mem"; |
| interrupts = <0 123 0>, <0 138 0>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| clocks = <&gcc GCC_SDCC1_APPS_CLK>, |
| <&gcc GCC_SDCC1_AHB_CLK>, |
| <&xo_board>; |
| clock-names = "core", "iface", "xo"; |
| status = "disabled"; |
| }; |
| |
| sdhci@f98a4900 { |
| compatible = "qcom,sdhci-msm-v4"; |
| reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>; |
| reg-names = "hc_mem", "core_mem"; |
| interrupts = <0 125 0>, <0 221 0>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| clocks = <&gcc GCC_SDCC2_APPS_CLK>, |
| <&gcc GCC_SDCC2_AHB_CLK>, |
| <&xo_board>; |
| clock-names = "core", "iface", "xo"; |
| status = "disabled"; |
| }; |
| |
| spmi_bus: spmi@fc4cf000 { |
| compatible = "qcom,spmi-pmic-arb"; |
| reg-names = "core", "intr", "cnfg"; |
| reg = <0xfc4cf000 0x1000>, |
| <0xfc4cb000 0x1000>, |
| <0xfc4ca000 0x1000>; |
| interrupt-names = "periph_irq"; |
| interrupts = <0 190 0>; |
| qcom,ee = <0>; |
| qcom,channel = <0>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| interrupt-controller; |
| #interrupt-cells = <4>; |
| }; |
| }; |
| |
| smd { |
| compatible = "qcom,smd"; |
| |
| rpm { |
| interrupts = <0 168 1>; |
| qcom,ipc = <&apcs 8 0>; |
| qcom,smd-edge = <15>; |
| |
| rpm_requests { |
| compatible = "qcom,rpm-apq8084"; |
| qcom,smd-channels = "rpm_requests"; |
| |
| pma8084-regulators { |
| compatible = "qcom,rpm-pma8084-regulators"; |
| |
| pma8084_s1: s1 {}; |
| pma8084_s2: s2 {}; |
| pma8084_s3: s3 {}; |
| pma8084_s4: s4 {}; |
| pma8084_s5: s5 {}; |
| pma8084_s6: s6 {}; |
| pma8084_s7: s7 {}; |
| pma8084_s8: s8 {}; |
| pma8084_s9: s9 {}; |
| pma8084_s10: s10 {}; |
| pma8084_s11: s11 {}; |
| pma8084_s12: s12 {}; |
| |
| pma8084_l1: l1 {}; |
| pma8084_l2: l2 {}; |
| pma8084_l3: l3 {}; |
| pma8084_l4: l4 {}; |
| pma8084_l5: l5 {}; |
| pma8084_l6: l6 {}; |
| pma8084_l7: l7 {}; |
| pma8084_l8: l8 {}; |
| pma8084_l9: l9 {}; |
| pma8084_l10: l10 {}; |
| pma8084_l11: l11 {}; |
| pma8084_l12: l12 {}; |
| pma8084_l13: l13 {}; |
| pma8084_l14: l14 {}; |
| pma8084_l15: l15 {}; |
| pma8084_l16: l16 {}; |
| pma8084_l17: l17 {}; |
| pma8084_l18: l18 {}; |
| pma8084_l19: l19 {}; |
| pma8084_l20: l20 {}; |
| pma8084_l21: l21 {}; |
| pma8084_l22: l22 {}; |
| pma8084_l23: l23 {}; |
| pma8084_l24: l24 {}; |
| pma8084_l25: l25 {}; |
| pma8084_l26: l26 {}; |
| pma8084_l27: l27 {}; |
| |
| pma8084_lvs1: lvs1 {}; |
| pma8084_lvs2: lvs2 {}; |
| pma8084_lvs3: lvs3 {}; |
| pma8084_lvs4: lvs4 {}; |
| |
| pma8084_5vs1: 5vs1 {}; |
| }; |
| }; |
| }; |
| }; |
| }; |