openrisc: enable LOCKDEP_SUPPORT and irqflags tracing
Lockdep is needed for proving the spinlocks and rwlocks work fine on our
platform. It also requires calling the trace_hardirqs_off() and
trace_hardirqs_on() pair of routines when entering and exiting an
interrupt.
For OpenRISC the interrupt stack frame does not support frame pointers,
so to call trace_hardirqs_on() and trace_hardirqs_off() here the macro's
build up a stack frame each time.
There is one necessary small change in _sys_call_handler to move
interrupt enabling later so they can get re-enabled during syscall
restart. This was done to fix lockdep warnings that are now possible due
to this
patch.
Signed-off-by: Stafford Horne <shorne@gmail.com>
diff --git a/arch/openrisc/Kconfig b/arch/openrisc/Kconfig
index 399f55e..f8cfb3b 100644
--- a/arch/openrisc/Kconfig
+++ b/arch/openrisc/Kconfig
@@ -64,6 +64,9 @@
config STACKTRACE_SUPPORT
def_bool y
+config LOCKDEP_SUPPORT
+ def_bool y
+
source "init/Kconfig"
source "kernel/Kconfig.freezer"
diff --git a/arch/openrisc/kernel/entry.S b/arch/openrisc/kernel/entry.S
index 1b7160c..690d552 100644
--- a/arch/openrisc/kernel/entry.S
+++ b/arch/openrisc/kernel/entry.S
@@ -42,6 +42,61 @@
/* =========================================================[ macros ]=== */
+#ifdef CONFIG_TRACE_IRQFLAGS
+/*
+ * Trace irq on/off creating a stack frame.
+ */
+#define TRACE_IRQS_OP(trace_op) \
+ l.sw -8(r1),r2 /* store frame pointer */ ;\
+ l.sw -4(r1),r9 /* store return address */ ;\
+ l.addi r2,r1,0 /* move sp to fp */ ;\
+ l.jal trace_op ;\
+ l.addi r1,r1,-8 ;\
+ l.ori r1,r2,0 /* restore sp */ ;\
+ l.lwz r9,-4(r1) /* restore return address */ ;\
+ l.lwz r2,-8(r1) /* restore fp */ ;\
+/*
+ * Trace irq on/off and save registers we need that would otherwise be
+ * clobbered.
+ */
+#define TRACE_IRQS_SAVE(t1,trace_op) \
+ l.sw -12(r1),t1 /* save extra reg */ ;\
+ l.sw -8(r1),r2 /* store frame pointer */ ;\
+ l.sw -4(r1),r9 /* store return address */ ;\
+ l.addi r2,r1,0 /* move sp to fp */ ;\
+ l.jal trace_op ;\
+ l.addi r1,r1,-12 ;\
+ l.ori r1,r2,0 /* restore sp */ ;\
+ l.lwz r9,-4(r1) /* restore return address */ ;\
+ l.lwz r2,-8(r1) /* restore fp */ ;\
+ l.lwz t1,-12(r1) /* restore extra reg */
+
+#define TRACE_IRQS_OFF TRACE_IRQS_OP(trace_hardirqs_off)
+#define TRACE_IRQS_ON TRACE_IRQS_OP(trace_hardirqs_on)
+#define TRACE_IRQS_ON_SYSCALL \
+ TRACE_IRQS_SAVE(r10,trace_hardirqs_on) ;\
+ l.lwz r3,PT_GPR3(r1) ;\
+ l.lwz r4,PT_GPR4(r1) ;\
+ l.lwz r5,PT_GPR5(r1) ;\
+ l.lwz r6,PT_GPR6(r1) ;\
+ l.lwz r7,PT_GPR7(r1) ;\
+ l.lwz r8,PT_GPR8(r1) ;\
+ l.lwz r11,PT_GPR11(r1)
+#define TRACE_IRQS_OFF_ENTRY \
+ l.lwz r5,PT_SR(r1) ;\
+ l.andi r3,r5,(SPR_SR_IEE|SPR_SR_TEE) ;\
+ l.sfeq r5,r0 /* skip trace if irqs were already off */;\
+ l.bf 1f ;\
+ l.nop ;\
+ TRACE_IRQS_SAVE(r4,trace_hardirqs_off) ;\
+1:
+#else
+#define TRACE_IRQS_OFF
+#define TRACE_IRQS_ON
+#define TRACE_IRQS_OFF_ENTRY
+#define TRACE_IRQS_ON_SYSCALL
+#endif
+
/*
* We need to disable interrupts at beginning of RESTORE_ALL
* since interrupt might come in after we've loaded EPC return address
@@ -124,6 +179,7 @@
/* r30 already save */ ;\
/* l.sw PT_GPR30(r1),r30*/ ;\
l.sw PT_GPR31(r1),r31 ;\
+ TRACE_IRQS_OFF_ENTRY ;\
/* Store -1 in orig_gpr11 for non-syscall exceptions */ ;\
l.addi r30,r0,-1 ;\
l.sw PT_ORIG_GPR11(r1),r30
@@ -557,9 +613,6 @@
.align 4
ENTRY(_sys_call_handler)
- /* syscalls run with interrupts enabled */
- ENABLE_INTERRUPTS(r29) // enable interrupts, r29 is temp
-
/* r1, EPCR, ESR a already saved */
l.sw PT_GPR2(r1),r2
/* r3-r8 must be saved because syscall restart relies
@@ -597,6 +650,10 @@
/* l.sw PT_GPR30(r1),r30 */
_syscall_check_trace_enter:
+ /* syscalls run with interrupts enabled */
+ TRACE_IRQS_ON_SYSCALL
+ ENABLE_INTERRUPTS(r29) // enable interrupts, r29 is temp
+
/* If TIF_SYSCALL_TRACE is set, then we want to do syscall tracing */
l.lwz r30,TI_FLAGS(r10)
l.andi r30,r30,_TIF_SYSCALL_TRACE
@@ -657,6 +714,7 @@
_syscall_check_work:
/* Here we need to disable interrupts */
DISABLE_INTERRUPTS(r27,r29)
+ TRACE_IRQS_OFF
l.lwz r30,TI_FLAGS(r10)
l.andi r30,r30,_TIF_WORK_MASK
l.sfne r30,r0
@@ -871,6 +929,7 @@
_resume_userspace:
DISABLE_INTERRUPTS(r3,r4)
+ TRACE_IRQS_OFF
l.lwz r4,TI_FLAGS(r10)
l.andi r13,r4,_TIF_WORK_MASK
l.sfeqi r13,0
@@ -909,6 +968,15 @@
l.lwz r8,PT_GPR8(r1)
_restore_all:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ l.lwz r4,PT_SR(r1)
+ l.andi r3,r4,(SPR_SR_IEE|SPR_SR_TEE)
+ l.sfeq r3,r0 /* skip trace if irqs were off */
+ l.bf skip_hardirqs_on
+ l.nop
+ TRACE_IRQS_ON
+skip_hardirqs_on:
+#endif
RESTORE_ALL
/* This returns to userspace code */