powerpc/t2080rdb: Add T2080RDB board support
T2080PCIe-RDB is a Freescale Reference Design Board that hosts T2080 SoC.
The board feature overview:
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
DDR Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LP devices
- 72bit 4GB DDR3-LP SODIMM in slot
Ethernet interfaces:
- Two 1Gbps RGMII ports on-board
- Two 10Gbps SFP+ ports on-board
- Two 10Gbps Base-T ports on-board
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
IFC/Local Bus
- NOR: 128MB 16-bit NOR flash
- NAND: 1GB 8-bit NAND flash
- CPLD: for system controlling with programable header on-board
eSPI:
- 64MB N25Q512 SPI flash
USB:
- Two USB2.0 ports with internal PHY (both Type-A)
PCIe:
- One PCIe x4 goldfinger(support SR-IOV)
- One PCIe x4 slot
- One PCIe x2 end-point device (C293 crypto co-processor)
SATA:
- Two SATA 2.0 ports on-board
SDHC:
- support a MicroSD/TF card on-board
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
diff --git a/arch/powerpc/boot/dts/t2080rdb.dts b/arch/powerpc/boot/dts/t2080rdb.dts
new file mode 100644
index 0000000..e889104
--- /dev/null
+++ b/arch/powerpc/boot/dts/t2080rdb.dts
@@ -0,0 +1,57 @@
+/*
+ * T2080PCIe-RDB Board Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t208xsi-pre.dtsi"
+/include/ "t208xrdb.dtsi"
+
+/ {
+ model = "fsl,T2080RDB";
+ compatible = "fsl,T2080RDB";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ rio: rapidio@ffe0c0000 {
+ reg = <0xf 0xfe0c0000 0 0x11000>;
+
+ port1 {
+ ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+ };
+ port2 {
+ ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+ };
+ };
+};
+
+/include/ "fsl/t2080si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/t208xrdb.dtsi b/arch/powerpc/boot/dts/t208xrdb.dtsi
new file mode 100644
index 0000000..1481e19
--- /dev/null
+++ b/arch/powerpc/boot/dts/t208xrdb.dtsi
@@ -0,0 +1,184 @@
+/*
+ * T2080PCIe-RDB Board Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/ {
+ model = "fsl,T2080RDB";
+ compatible = "fsl,T2080RDB";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ ifc: localbus@ffe124000 {
+ reg = <0xf 0xfe124000 0 0x2000>;
+ ranges = <0 0 0xf 0xe8000000 0x08000000
+ 2 0 0xf 0xff800000 0x00010000
+ 3 0 0xf 0xffdf0000 0x00008000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc-nand";
+ reg = <0x2 0x0 0x10000>;
+ };
+
+ boardctrl: board-control@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,t2080-cpld";
+ reg = <3 0 0x300>;
+ ranges = <0 3 0 0x300>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ dcsr: dcsr@f00000000 {
+ ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+ };
+
+ soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
+ spi@110000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q512a";
+ reg = <0>;
+ spi-max-frequency = <10000000>; /* input clock */
+ };
+ };
+
+ i2c@118000 {
+ adt7481@4c {
+ compatible = "adi,adt7481";
+ reg = <0x4c>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ interrupts = <0x1 0x1 0 0>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c256";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@118100 {
+ pca9546@77 {
+ compatible = "nxp,pca9546";
+ reg = <0x77>;
+ };
+ };
+
+ sdhc@114000 {
+ voltage-ranges = <1800 1800 3300 3300>;
+ };
+ };
+
+ pci0: pcie@ffe240000 {
+ reg = <0xf 0xfe240000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
+ 0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci1: pcie@ffe250000 {
+ reg = <0xf 0xfe250000 0 0x10000>;
+ ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x10000000
+ 0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci2: pcie@ffe260000 {
+ reg = <0xf 0xfe260000 0 0x1000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x30000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci3: pcie@ffe270000 {
+ reg = <0xf 0xfe270000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x40000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8030000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+};
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 5063696..0c1e690 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -274,7 +274,7 @@
For 32bit kernel, the following boards are supported:
P2041 RDB, P3041 DS, P4080 DS, kmcoge4, and OCA4080
For 64bit kernel, the following boards are supported:
- T208x QDS, T4240 QDS/RDB and B4 QDS
+ T208x QDS/RDB, T4240 QDS/RDB and B4 QDS
The following boards are supported for both 32bit and 64bit kernel:
P5020 DS, P5040 DS and T104xQDS
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index 4f22ad1..d22dd85 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -120,6 +120,7 @@
"fsl,P5020DS",
"fsl,P5040DS",
"fsl,T2080QDS",
+ "fsl,T2080RDB",
"fsl,T2081QDS",
"fsl,T4240QDS",
"fsl,T4240RDB",