e1000e: initial support for i219
i219 is the next-generation LOM that will be available on systems with the
Sunrise Point Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support for the device.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Carmen Edwards <carmenx.edwards@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index bb7ab3c..0570c66 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -141,6 +141,7 @@
#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
#define E1000_RCTL_RDMTS_HALF 0x00000000 /* Rx desc min threshold size */
+#define E1000_RCTL_RDMTS_HEX 0x00010000
#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 9416e5a..a69f09e 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -132,6 +132,7 @@
board_pchlan,
board_pch2lan,
board_pch_lpt,
+ board_pch_spt
};
struct e1000_ps_page {
@@ -501,6 +502,7 @@
extern const struct e1000_info e1000_pch_info;
extern const struct e1000_info e1000_pch2_info;
extern const struct e1000_info e1000_pch_lpt_info;
+extern const struct e1000_info e1000_pch_spt_info;
extern const struct e1000_info e1000_es2_info;
void e1000e_ptp_init(struct e1000_adapter *adapter);
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 865ce45..11f486e 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -896,18 +896,20 @@
case e1000_pchlan:
case e1000_pch2lan:
case e1000_pch_lpt:
+ case e1000_pch_spt:
mask |= (1 << 18);
break;
default:
break;
}
- if (mac->type == e1000_pch_lpt)
+ if ((mac->type == e1000_pch_lpt) || (mac->type == e1000_pch_spt))
wlock_mac = (er32(FWSM) & E1000_FWSM_WLOCK_MAC_MASK) >>
E1000_FWSM_WLOCK_MAC_SHIFT;
for (i = 0; i < mac->rar_entry_count; i++) {
- if (mac->type == e1000_pch_lpt) {
+ if ((mac->type == e1000_pch_lpt) ||
+ (mac->type == e1000_pch_spt)) {
/* Cannot test write-protected SHRAL[n] registers */
if ((wlock_mac == 1) || (wlock_mac && (i > wlock_mac)))
continue;
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 72f5475..19e8c48 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -87,6 +87,10 @@
#define E1000_DEV_ID_PCH_I218_V2 0x15A1
#define E1000_DEV_ID_PCH_I218_LM3 0x15A2 /* Wildcat Point PCH */
#define E1000_DEV_ID_PCH_I218_V3 0x15A3 /* Wildcat Point PCH */
+#define E1000_DEV_ID_PCH_SPT_I219_LM 0x156F /* SPT PCH */
+#define E1000_DEV_ID_PCH_SPT_I219_V 0x1570 /* SPT PCH */
+#define E1000_DEV_ID_PCH_SPT_I219_LM2 0x15B7 /* SPT-H PCH */
+#define E1000_DEV_ID_PCH_SPT_I219_V2 0x15B8 /* SPT-H PCH */
#define E1000_REVISION_4 4
@@ -108,6 +112,7 @@
e1000_pchlan,
e1000_pch2lan,
e1000_pch_lpt,
+ e1000_pch_spt,
};
enum e1000_media_type {
@@ -153,6 +158,7 @@
e1000_bus_width_pcie_x1,
e1000_bus_width_pcie_x2,
e1000_bus_width_pcie_x4 = 4,
+ e1000_bus_width_pcie_x8 = 8,
e1000_bus_width_32,
e1000_bus_width_64,
e1000_bus_width_reserved
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 48b74a5..7523f51 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -123,6 +123,14 @@
u16 *data);
static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
u8 size, u16 *data);
+static s32 e1000_read_flash_data32_ich8lan(struct e1000_hw *hw, u32 offset,
+ u32 *data);
+static s32 e1000_read_flash_dword_ich8lan(struct e1000_hw *hw,
+ u32 offset, u32 *data);
+static s32 e1000_write_flash_data32_ich8lan(struct e1000_hw *hw,
+ u32 offset, u32 data);
+static s32 e1000_retry_write_flash_dword_ich8lan(struct e1000_hw *hw,
+ u32 offset, u32 dword);
static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw);
static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw);
static s32 e1000_led_on_ich8lan(struct e1000_hw *hw);
@@ -229,7 +237,8 @@
if (ret_val)
return false;
out:
- if (hw->mac.type == e1000_pch_lpt) {
+ if ((hw->mac.type == e1000_pch_lpt) ||
+ (hw->mac.type == e1000_pch_spt)) {
/* Unforce SMBus mode in PHY */
e1e_rphy_locked(hw, CV_SMB_CTRL, &phy_reg);
phy_reg &= ~CV_SMB_CTRL_FORCE_SMBUS;
@@ -321,6 +330,7 @@
*/
switch (hw->mac.type) {
case e1000_pch_lpt:
+ case e1000_pch_spt:
if (e1000_phy_is_accessible_pchlan(hw))
break;
@@ -461,6 +471,7 @@
/* fall-through */
case e1000_pch2lan:
case e1000_pch_lpt:
+ case e1000_pch_spt:
/* In case the PHY needs to be in mdio slow mode,
* set slow mode and try to get the PHY id again.
*/
@@ -590,35 +601,50 @@
struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
u32 gfpreg, sector_base_addr, sector_end_addr;
u16 i;
+ u32 nvm_size;
/* Can't read flash registers if the register set isn't mapped. */
- if (!hw->flash_address) {
- e_dbg("ERROR: Flash registers not mapped\n");
- return -E1000_ERR_CONFIG;
- }
-
nvm->type = e1000_nvm_flash_sw;
-
- gfpreg = er32flash(ICH_FLASH_GFPREG);
-
- /* sector_X_addr is a "sector"-aligned address (4096 bytes)
- * Add 1 to sector_end_addr since this sector is included in
- * the overall size.
+ /* in SPT, gfpreg doesn't exist. NVM size is taken from the
+ * STRAP register
*/
- sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK;
- sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1;
+ if (hw->mac.type == e1000_pch_spt) {
+ nvm->flash_base_addr = 0;
+ nvm_size = (((er32(STRAP) >> 1) & 0x1F) + 1)
+ * NVM_SIZE_MULTIPLIER;
+ nvm->flash_bank_size = nvm_size / 2;
+ /* Adjust to word count */
+ nvm->flash_bank_size /= sizeof(u16);
+ /* Set the base address for flash register access */
+ hw->flash_address = hw->hw_addr + E1000_FLASH_BASE_ADDR;
+ } else {
+ if (!hw->flash_address) {
+ e_dbg("ERROR: Flash registers not mapped\n");
+ return -E1000_ERR_CONFIG;
+ }
- /* flash_base_addr is byte-aligned */
- nvm->flash_base_addr = sector_base_addr << FLASH_SECTOR_ADDR_SHIFT;
+ gfpreg = er32flash(ICH_FLASH_GFPREG);
- /* find total size of the NVM, then cut in half since the total
- * size represents two separate NVM banks.
- */
- nvm->flash_bank_size = ((sector_end_addr - sector_base_addr)
- << FLASH_SECTOR_ADDR_SHIFT);
- nvm->flash_bank_size /= 2;
- /* Adjust to word count */
- nvm->flash_bank_size /= sizeof(u16);
+ /* sector_X_addr is a "sector"-aligned address (4096 bytes)
+ * Add 1 to sector_end_addr since this sector is included in
+ * the overall size.
+ */
+ sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK;
+ sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1;
+
+ /* flash_base_addr is byte-aligned */
+ nvm->flash_base_addr = sector_base_addr
+ << FLASH_SECTOR_ADDR_SHIFT;
+
+ /* find total size of the NVM, then cut in half since the total
+ * size represents two separate NVM banks.
+ */
+ nvm->flash_bank_size = ((sector_end_addr - sector_base_addr)
+ << FLASH_SECTOR_ADDR_SHIFT);
+ nvm->flash_bank_size /= 2;
+ /* Adjust to word count */
+ nvm->flash_bank_size /= sizeof(u16);
+ }
nvm->word_size = E1000_ICH8_SHADOW_RAM_WORDS;
@@ -682,6 +708,7 @@
mac->ops.rar_set = e1000_rar_set_pch2lan;
/* fall-through */
case e1000_pch_lpt:
+ case e1000_pch_spt:
case e1000_pchlan:
/* check management mode */
mac->ops.check_mng_mode = e1000_check_mng_mode_pchlan;
@@ -699,7 +726,7 @@
break;
}
- if (mac->type == e1000_pch_lpt) {
+ if ((mac->type == e1000_pch_lpt) || (mac->type == e1000_pch_spt)) {
mac->rar_entry_count = E1000_PCH_LPT_RAR_ENTRIES;
mac->ops.rar_set = e1000_rar_set_pch_lpt;
mac->ops.setup_physical_interface =
@@ -919,8 +946,9 @@
/* clear FEXTNVM6 bit 8 on link down or 10/100 */
fextnvm6 &= ~E1000_FEXTNVM6_REQ_PLL_CLK;
- if (!link || ((status & E1000_STATUS_SPEED_100) &&
- (status & E1000_STATUS_FD)))
+ if ((hw->phy.revision > 5) || !link ||
+ ((status & E1000_STATUS_SPEED_100) &&
+ (status & E1000_STATUS_FD)))
goto update_fextnvm6;
ret_val = e1e_rphy(hw, I217_INBAND_CTRL, ®);
@@ -1100,6 +1128,21 @@
if (ret_val)
goto out;
+ /* Si workaround for ULP entry flow on i127/rev6 h/w. Enable
+ * LPLU and disable Gig speed when entering ULP
+ */
+ if ((hw->phy.type == e1000_phy_i217) && (hw->phy.revision == 6)) {
+ ret_val = e1000_read_phy_reg_hv_locked(hw, HV_OEM_BITS,
+ &phy_reg);
+ if (ret_val)
+ goto release;
+ phy_reg |= HV_OEM_BITS_LPLU | HV_OEM_BITS_GBE_DIS;
+ ret_val = e1000_write_phy_reg_hv_locked(hw, HV_OEM_BITS,
+ phy_reg);
+ if (ret_val)
+ goto release;
+ }
+
/* Force SMBus mode in PHY */
ret_val = e1000_read_phy_reg_hv_locked(hw, CV_SMB_CTRL, &phy_reg);
if (ret_val)
@@ -1302,7 +1345,8 @@
static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
{
struct e1000_mac_info *mac = &hw->mac;
- s32 ret_val;
+ s32 ret_val, tipg_reg = 0;
+ u16 emi_addr, emi_val = 0;
bool link;
u16 phy_reg;
@@ -1333,48 +1377,55 @@
* the IPG and reduce Rx latency in the PHY.
*/
if (((hw->mac.type == e1000_pch2lan) ||
- (hw->mac.type == e1000_pch_lpt)) && link) {
+ (hw->mac.type == e1000_pch_lpt) ||
+ (hw->mac.type == e1000_pch_spt)) && link) {
u32 reg;
reg = er32(STATUS);
+ tipg_reg = er32(TIPG);
+ tipg_reg &= ~E1000_TIPG_IPGT_MASK;
+
if (!(reg & (E1000_STATUS_FD | E1000_STATUS_SPEED_MASK))) {
- u16 emi_addr;
-
- reg = er32(TIPG);
- reg &= ~E1000_TIPG_IPGT_MASK;
- reg |= 0xFF;
- ew32(TIPG, reg);
-
+ tipg_reg |= 0xFF;
/* Reduce Rx latency in analog PHY */
- ret_val = hw->phy.ops.acquire(hw);
- if (ret_val)
- return ret_val;
+ emi_val = 0;
+ } else {
- if (hw->mac.type == e1000_pch2lan)
- emi_addr = I82579_RX_CONFIG;
- else
- emi_addr = I217_RX_CONFIG;
-
- ret_val = e1000_write_emi_reg_locked(hw, emi_addr, 0);
-
- hw->phy.ops.release(hw);
-
- if (ret_val)
- return ret_val;
+ /* Roll back the default values */
+ tipg_reg |= 0x08;
+ emi_val = 1;
}
+
+ ew32(TIPG, tipg_reg);
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+
+ if (hw->mac.type == e1000_pch2lan)
+ emi_addr = I82579_RX_CONFIG;
+ else
+ emi_addr = I217_RX_CONFIG;
+ ret_val = e1000_write_emi_reg_locked(hw, emi_addr, emi_val);
+
+ hw->phy.ops.release(hw);
+
+ if (ret_val)
+ return ret_val;
}
/* Work-around I218 hang issue */
if ((hw->adapter->pdev->device == E1000_DEV_ID_PCH_LPTLP_I218_LM) ||
(hw->adapter->pdev->device == E1000_DEV_ID_PCH_LPTLP_I218_V) ||
(hw->adapter->pdev->device == E1000_DEV_ID_PCH_I218_LM3) ||
- (hw->adapter->pdev->device == E1000_DEV_ID_PCH_I218_V3)) {
+ (hw->adapter->pdev->device == E1000_DEV_ID_PCH_I218_V3) ||
+ (hw->mac.type == e1000_pch_spt)) {
ret_val = e1000_k1_workaround_lpt_lp(hw, link);
if (ret_val)
return ret_val;
}
-
- if (hw->mac.type == e1000_pch_lpt) {
+ if ((hw->mac.type == e1000_pch_lpt) ||
+ (hw->mac.type == e1000_pch_spt)) {
/* Set platform power management values for
* Latency Tolerance Reporting (LTR)
*/
@@ -1386,6 +1437,19 @@
/* Clear link partner's EEE ability */
hw->dev_spec.ich8lan.eee_lp_ability = 0;
+ /* FEXTNVM6 K1-off workaround */
+ if (hw->mac.type == e1000_pch_spt) {
+ u32 pcieanacfg = er32(PCIEANACFG);
+ u32 fextnvm6 = er32(FEXTNVM6);
+
+ if (pcieanacfg & E1000_FEXTNVM6_K1_OFF_ENABLE)
+ fextnvm6 |= E1000_FEXTNVM6_K1_OFF_ENABLE;
+ else
+ fextnvm6 &= ~E1000_FEXTNVM6_K1_OFF_ENABLE;
+
+ ew32(FEXTNVM6, fextnvm6);
+ }
+
if (!link)
return 0; /* No link detected */
@@ -1479,6 +1543,7 @@
case e1000_pchlan:
case e1000_pch2lan:
case e1000_pch_lpt:
+ case e1000_pch_spt:
rc = e1000_init_phy_params_pchlan(hw);
break;
default:
@@ -1929,6 +1994,7 @@
case e1000_pchlan:
case e1000_pch2lan:
case e1000_pch_lpt:
+ case e1000_pch_spt:
sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
break;
default:
@@ -2961,6 +3027,20 @@
s32 ret_val;
switch (hw->mac.type) {
+ /* In SPT, read from the CTRL_EXT reg instead of
+ * accessing the sector valid bits from the nvm
+ */
+ case e1000_pch_spt:
+ *bank = er32(CTRL_EXT)
+ & E1000_CTRL_EXT_NVMVS;
+ if ((*bank == 0) || (*bank == 1)) {
+ e_dbg("ERROR: No valid NVM bank present\n");
+ return -E1000_ERR_NVM;
+ } else {
+ *bank = *bank - 2;
+ return 0;
+ }
+ break;
case e1000_ich8lan:
case e1000_ich9lan:
eecd = er32(EECD);
@@ -3008,6 +3088,99 @@
}
/**
+ * e1000_read_nvm_spt - NVM access for SPT
+ * @hw: pointer to the HW structure
+ * @offset: The offset (in bytes) of the word(s) to read.
+ * @words: Size of data to read in words.
+ * @data: pointer to the word(s) to read at offset.
+ *
+ * Reads a word(s) from the NVM
+ **/
+static s32 e1000_read_nvm_spt(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u32 act_offset;
+ s32 ret_val = 0;
+ u32 bank = 0;
+ u32 dword = 0;
+ u16 offset_to_read;
+ u16 i;
+
+ if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) ||
+ (words == 0)) {
+ e_dbg("nvm parameter(s) out of bounds\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+ nvm->ops.acquire(hw);
+
+ ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
+ if (ret_val) {
+ e_dbg("Could not detect valid bank, assuming bank 0\n");
+ bank = 0;
+ }
+
+ act_offset = (bank) ? nvm->flash_bank_size : 0;
+ act_offset += offset;
+
+ ret_val = 0;
+
+ for (i = 0; i < words; i += 2) {
+ if (words - i == 1) {
+ if (dev_spec->shadow_ram[offset + i].modified) {
+ data[i] =
+ dev_spec->shadow_ram[offset + i].value;
+ } else {
+ offset_to_read = act_offset + i -
+ ((act_offset + i) % 2);
+ ret_val =
+ e1000_read_flash_dword_ich8lan(hw,
+ offset_to_read,
+ &dword);
+ if (ret_val)
+ break;
+ if ((act_offset + i) % 2 == 0)
+ data[i] = (u16)(dword & 0xFFFF);
+ else
+ data[i] = (u16)((dword >> 16) & 0xFFFF);
+ }
+ } else {
+ offset_to_read = act_offset + i;
+ if (!(dev_spec->shadow_ram[offset + i].modified) ||
+ !(dev_spec->shadow_ram[offset + i + 1].modified)) {
+ ret_val =
+ e1000_read_flash_dword_ich8lan(hw,
+ offset_to_read,
+ &dword);
+ if (ret_val)
+ break;
+ }
+ if (dev_spec->shadow_ram[offset + i].modified)
+ data[i] =
+ dev_spec->shadow_ram[offset + i].value;
+ else
+ data[i] = (u16)(dword & 0xFFFF);
+ if (dev_spec->shadow_ram[offset + i].modified)
+ data[i + 1] =
+ dev_spec->shadow_ram[offset + i + 1].value;
+ else
+ data[i + 1] = (u16)(dword >> 16 & 0xFFFF);
+ }
+ }
+
+ nvm->ops.release(hw);
+
+out:
+ if (ret_val)
+ e_dbg("NVM read error: %d\n", ret_val);
+
+ return ret_val;
+}
+
+/**
* e1000_read_nvm_ich8lan - Read word(s) from the NVM
* @hw: pointer to the HW structure
* @offset: The offset (in bytes) of the word(s) to read.
@@ -3090,8 +3263,10 @@
/* Clear FCERR and DAEL in hw status by writing 1 */
hsfsts.hsf_status.flcerr = 1;
hsfsts.hsf_status.dael = 1;
-
- ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
+ if (hw->mac.type == e1000_pch_spt)
+ ew32flash(ICH_FLASH_HSFSTS, hsfsts.regval & 0xFFFF);
+ else
+ ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
/* Either we should have a hardware SPI cycle in progress
* bit to check against, in order to start a new cycle or
@@ -3107,7 +3282,10 @@
* Begin by setting Flash Cycle Done.
*/
hsfsts.hsf_status.flcdone = 1;
- ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
+ if (hw->mac.type == e1000_pch_spt)
+ ew32flash(ICH_FLASH_HSFSTS, hsfsts.regval & 0xFFFF);
+ else
+ ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
ret_val = 0;
} else {
s32 i;
@@ -3128,7 +3306,11 @@
* now set the Flash Cycle Done.
*/
hsfsts.hsf_status.flcdone = 1;
- ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
+ if (hw->mac.type == e1000_pch_spt)
+ ew32flash(ICH_FLASH_HSFSTS,
+ hsfsts.regval & 0xFFFF);
+ else
+ ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
} else {
e_dbg("Flash controller busy, cannot get access\n");
}
@@ -3151,9 +3333,16 @@
u32 i = 0;
/* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */
- hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
+ if (hw->mac.type == e1000_pch_spt)
+ hsflctl.regval = er32flash(ICH_FLASH_HSFSTS) >> 16;
+ else
+ hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
hsflctl.hsf_ctrl.flcgo = 1;
- ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
+
+ if (hw->mac.type == e1000_pch_spt)
+ ew32flash(ICH_FLASH_HSFSTS, hsflctl.regval << 16);
+ else
+ ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
/* wait till FDONE bit is set to 1 */
do {
@@ -3170,6 +3359,23 @@
}
/**
+ * e1000_read_flash_dword_ich8lan - Read dword from flash
+ * @hw: pointer to the HW structure
+ * @offset: offset to data location
+ * @data: pointer to the location for storing the data
+ *
+ * Reads the flash dword at offset into data. Offset is converted
+ * to bytes before read.
+ **/
+static s32 e1000_read_flash_dword_ich8lan(struct e1000_hw *hw, u32 offset,
+ u32 *data)
+{
+ /* Must convert word offset into bytes. */
+ offset <<= 1;
+ return e1000_read_flash_data32_ich8lan(hw, offset, data);
+}
+
+/**
* e1000_read_flash_word_ich8lan - Read word from flash
* @hw: pointer to the HW structure
* @offset: offset to data location
@@ -3201,7 +3407,14 @@
s32 ret_val;
u16 word = 0;
- ret_val = e1000_read_flash_data_ich8lan(hw, offset, 1, &word);
+ /* In SPT, only 32 bits access is supported,
+ * so this function should not be called.
+ */
+ if (hw->mac.type == e1000_pch_spt)
+ return -E1000_ERR_NVM;
+ else
+ ret_val = e1000_read_flash_data_ich8lan(hw, offset, 1, &word);
+
if (ret_val)
return ret_val;
@@ -3287,6 +3500,82 @@
}
/**
+ * e1000_read_flash_data32_ich8lan - Read dword from NVM
+ * @hw: pointer to the HW structure
+ * @offset: The offset (in bytes) of the dword to read.
+ * @data: Pointer to the dword to store the value read.
+ *
+ * Reads a byte or word from the NVM using the flash access registers.
+ **/
+
+static s32 e1000_read_flash_data32_ich8lan(struct e1000_hw *hw, u32 offset,
+ u32 *data)
+{
+ union ich8_hws_flash_status hsfsts;
+ union ich8_hws_flash_ctrl hsflctl;
+ u32 flash_linear_addr;
+ s32 ret_val = -E1000_ERR_NVM;
+ u8 count = 0;
+
+ if (offset > ICH_FLASH_LINEAR_ADDR_MASK ||
+ hw->mac.type != e1000_pch_spt)
+ return -E1000_ERR_NVM;
+ flash_linear_addr = ((ICH_FLASH_LINEAR_ADDR_MASK & offset) +
+ hw->nvm.flash_base_addr);
+
+ do {
+ udelay(1);
+ /* Steps */
+ ret_val = e1000_flash_cycle_init_ich8lan(hw);
+ if (ret_val)
+ break;
+ /* In SPT, This register is in Lan memory space, not flash.
+ * Therefore, only 32 bit access is supported
+ */
+ hsflctl.regval = er32flash(ICH_FLASH_HSFSTS) >> 16;
+
+ /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
+ hsflctl.hsf_ctrl.fldbcount = sizeof(u32) - 1;
+ hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ;
+ /* In SPT, This register is in Lan memory space, not flash.
+ * Therefore, only 32 bit access is supported
+ */
+ ew32flash(ICH_FLASH_HSFSTS, (u32)hsflctl.regval << 16);
+ ew32flash(ICH_FLASH_FADDR, flash_linear_addr);
+
+ ret_val =
+ e1000_flash_cycle_ich8lan(hw,
+ ICH_FLASH_READ_COMMAND_TIMEOUT);
+
+ /* Check if FCERR is set to 1, if set to 1, clear it
+ * and try the whole sequence a few more times, else
+ * read in (shift in) the Flash Data0, the order is
+ * least significant byte first msb to lsb
+ */
+ if (!ret_val) {
+ *data = er32flash(ICH_FLASH_FDATA0);
+ break;
+ } else {
+ /* If we've gotten here, then things are probably
+ * completely hosed, but if the error condition is
+ * detected, it won't hurt to give it another try...
+ * ICH_FLASH_CYCLE_REPEAT_COUNT times.
+ */
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcerr) {
+ /* Repeat for some time before giving up. */
+ continue;
+ } else if (!hsfsts.hsf_status.flcdone) {
+ e_dbg("Timeout error - flash cycle did not complete.\n");
+ break;
+ }
+ }
+ } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
+
+ return ret_val;
+}
+
+/**
* e1000_write_nvm_ich8lan - Write word(s) to the NVM
* @hw: pointer to the HW structure
* @offset: The offset (in bytes) of the word(s) to write.
@@ -3321,7 +3610,7 @@
}
/**
- * e1000_update_nvm_checksum_ich8lan - Update the checksum for NVM
+ * e1000_update_nvm_checksum_spt - Update the checksum for NVM
* @hw: pointer to the HW structure
*
* The NVM checksum is updated by calling the generic update_nvm_checksum,
@@ -3331,13 +3620,13 @@
* After a successful commit, the shadow ram is cleared and is ready for
* future writes.
**/
-static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
+static s32 e1000_update_nvm_checksum_spt(struct e1000_hw *hw)
{
struct e1000_nvm_info *nvm = &hw->nvm;
struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
u32 i, act_offset, new_bank_offset, old_bank_offset, bank;
s32 ret_val;
- u16 data;
+ u32 dword = 0;
ret_val = e1000e_update_nvm_checksum_generic(hw);
if (ret_val)
@@ -3371,12 +3660,175 @@
if (ret_val)
goto release;
}
-
- for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) {
+ for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i += 2) {
/* Determine whether to write the value stored
* in the other NVM bank or a modified value stored
* in the shadow RAM
*/
+ ret_val = e1000_read_flash_dword_ich8lan(hw,
+ i + old_bank_offset,
+ &dword);
+
+ if (dev_spec->shadow_ram[i].modified) {
+ dword &= 0xffff0000;
+ dword |= (dev_spec->shadow_ram[i].value & 0xffff);
+ }
+ if (dev_spec->shadow_ram[i + 1].modified) {
+ dword &= 0x0000ffff;
+ dword |= ((dev_spec->shadow_ram[i + 1].value & 0xffff)
+ << 16);
+ }
+ if (ret_val)
+ break;
+
+ /* If the word is 0x13, then make sure the signature bits
+ * (15:14) are 11b until the commit has completed.
+ * This will allow us to write 10b which indicates the
+ * signature is valid. We want to do this after the write
+ * has completed so that we don't mark the segment valid
+ * while the write is still in progress
+ */
+ if (i == E1000_ICH_NVM_SIG_WORD - 1)
+ dword |= E1000_ICH_NVM_SIG_MASK << 16;
+
+ /* Convert offset to bytes. */
+ act_offset = (i + new_bank_offset) << 1;
+
+ usleep_range(100, 200);
+
+ /* Write the data to the new bank. Offset in words */
+ act_offset = i + new_bank_offset;
+ ret_val = e1000_retry_write_flash_dword_ich8lan(hw, act_offset,
+ dword);
+ if (ret_val)
+ break;
+ }
+
+ /* Don't bother writing the segment valid bits if sector
+ * programming failed.
+ */
+ if (ret_val) {
+ /* Possibly read-only, see e1000e_write_protect_nvm_ich8lan() */
+ e_dbg("Flash commit failed.\n");
+ goto release;
+ }
+
+ /* Finally validate the new segment by setting bit 15:14
+ * to 10b in word 0x13 , this can be done without an
+ * erase as well since these bits are 11 to start with
+ * and we need to change bit 14 to 0b
+ */
+ act_offset = new_bank_offset + E1000_ICH_NVM_SIG_WORD;
+
+ /*offset in words but we read dword */
+ --act_offset;
+ ret_val = e1000_read_flash_dword_ich8lan(hw, act_offset, &dword);
+
+ if (ret_val)
+ goto release;
+
+ dword &= 0xBFFFFFFF;
+ ret_val = e1000_retry_write_flash_dword_ich8lan(hw, act_offset, dword);
+
+ if (ret_val)
+ goto release;
+
+ /* And invalidate the previously valid segment by setting
+ * its signature word (0x13) high_byte to 0b. This can be
+ * done without an erase because flash erase sets all bits
+ * to 1's. We can write 1's to 0's without an erase
+ */
+ act_offset = (old_bank_offset + E1000_ICH_NVM_SIG_WORD) * 2 + 1;
+
+ /* offset in words but we read dword */
+ act_offset = old_bank_offset + E1000_ICH_NVM_SIG_WORD - 1;
+ ret_val = e1000_read_flash_dword_ich8lan(hw, act_offset, &dword);
+
+ if (ret_val)
+ goto release;
+
+ dword &= 0x00FFFFFF;
+ ret_val = e1000_retry_write_flash_dword_ich8lan(hw, act_offset, dword);
+
+ if (ret_val)
+ goto release;
+
+ /* Great! Everything worked, we can now clear the cached entries. */
+ for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) {
+ dev_spec->shadow_ram[i].modified = false;
+ dev_spec->shadow_ram[i].value = 0xFFFF;
+ }
+
+release:
+ nvm->ops.release(hw);
+
+ /* Reload the EEPROM, or else modifications will not appear
+ * until after the next adapter reset.
+ */
+ if (!ret_val) {
+ nvm->ops.reload(hw);
+ usleep_range(10000, 20000);
+ }
+
+out:
+ if (ret_val)
+ e_dbg("NVM update error: %d\n", ret_val);
+
+ return ret_val;
+}
+
+/**
+ * e1000_update_nvm_checksum_ich8lan - Update the checksum for NVM
+ * @hw: pointer to the HW structure
+ *
+ * The NVM checksum is updated by calling the generic update_nvm_checksum,
+ * which writes the checksum to the shadow ram. The changes in the shadow
+ * ram are then committed to the EEPROM by processing each bank at a time
+ * checking for the modified bit and writing only the pending changes.
+ * After a successful commit, the shadow ram is cleared and is ready for
+ * future writes.
+ **/
+static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u32 i, act_offset, new_bank_offset, old_bank_offset, bank;
+ s32 ret_val;
+ u16 data = 0;
+
+ ret_val = e1000e_update_nvm_checksum_generic(hw);
+ if (ret_val)
+ goto out;
+
+ if (nvm->type != e1000_nvm_flash_sw)
+ goto out;
+
+ nvm->ops.acquire(hw);
+
+ /* We're writing to the opposite bank so if we're on bank 1,
+ * write to bank 0 etc. We also need to erase the segment that
+ * is going to be written
+ */
+ ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
+ if (ret_val) {
+ e_dbg("Could not detect valid bank, assuming bank 0\n");
+ bank = 0;
+ }
+
+ if (bank == 0) {
+ new_bank_offset = nvm->flash_bank_size;
+ old_bank_offset = 0;
+ ret_val = e1000_erase_flash_bank_ich8lan(hw, 1);
+ if (ret_val)
+ goto release;
+ } else {
+ old_bank_offset = nvm->flash_bank_size;
+ new_bank_offset = 0;
+ ret_val = e1000_erase_flash_bank_ich8lan(hw, 0);
+ if (ret_val)
+ goto release;
+ }
+ for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) {
if (dev_spec->shadow_ram[i].modified) {
data = dev_spec->shadow_ram[i].value;
} else {
@@ -3498,6 +3950,7 @@
*/
switch (hw->mac.type) {
case e1000_pch_lpt:
+ case e1000_pch_spt:
word = NVM_COMPAT;
valid_csum_mask = NVM_COMPAT_VALID_CSUM;
break;
@@ -3583,9 +4036,13 @@
s32 ret_val;
u8 count = 0;
- if (size < 1 || size > 2 || data > size * 0xff ||
- offset > ICH_FLASH_LINEAR_ADDR_MASK)
- return -E1000_ERR_NVM;
+ if (hw->mac.type == e1000_pch_spt) {
+ if (size != 4 || offset > ICH_FLASH_LINEAR_ADDR_MASK)
+ return -E1000_ERR_NVM;
+ } else {
+ if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK)
+ return -E1000_ERR_NVM;
+ }
flash_linear_addr = ((ICH_FLASH_LINEAR_ADDR_MASK & offset) +
hw->nvm.flash_base_addr);
@@ -3596,12 +4053,25 @@
ret_val = e1000_flash_cycle_init_ich8lan(hw);
if (ret_val)
break;
+ /* In SPT, This register is in Lan memory space, not
+ * flash. Therefore, only 32 bit access is supported
+ */
+ if (hw->mac.type == e1000_pch_spt)
+ hsflctl.regval = er32flash(ICH_FLASH_HSFSTS) >> 16;
+ else
+ hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
- hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
/* 0b/1b corresponds to 1 or 2 byte size, respectively. */
hsflctl.hsf_ctrl.fldbcount = size - 1;
hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE;
- ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
+ /* In SPT, This register is in Lan memory space,
+ * not flash. Therefore, only 32 bit access is
+ * supported
+ */
+ if (hw->mac.type == e1000_pch_spt)
+ ew32flash(ICH_FLASH_HSFSTS, hsflctl.regval << 16);
+ else
+ ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
ew32flash(ICH_FLASH_FADDR, flash_linear_addr);
@@ -3640,6 +4110,90 @@
}
/**
+* e1000_write_flash_data32_ich8lan - Writes 4 bytes to the NVM
+* @hw: pointer to the HW structure
+* @offset: The offset (in bytes) of the dwords to read.
+* @data: The 4 bytes to write to the NVM.
+*
+* Writes one/two/four bytes to the NVM using the flash access registers.
+**/
+static s32 e1000_write_flash_data32_ich8lan(struct e1000_hw *hw, u32 offset,
+ u32 data)
+{
+ union ich8_hws_flash_status hsfsts;
+ union ich8_hws_flash_ctrl hsflctl;
+ u32 flash_linear_addr;
+ s32 ret_val;
+ u8 count = 0;
+
+ if (hw->mac.type == e1000_pch_spt) {
+ if (offset > ICH_FLASH_LINEAR_ADDR_MASK)
+ return -E1000_ERR_NVM;
+ }
+ flash_linear_addr = ((ICH_FLASH_LINEAR_ADDR_MASK & offset) +
+ hw->nvm.flash_base_addr);
+ do {
+ udelay(1);
+ /* Steps */
+ ret_val = e1000_flash_cycle_init_ich8lan(hw);
+ if (ret_val)
+ break;
+
+ /* In SPT, This register is in Lan memory space, not
+ * flash. Therefore, only 32 bit access is supported
+ */
+ if (hw->mac.type == e1000_pch_spt)
+ hsflctl.regval = er32flash(ICH_FLASH_HSFSTS)
+ >> 16;
+ else
+ hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
+
+ hsflctl.hsf_ctrl.fldbcount = sizeof(u32) - 1;
+ hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE;
+
+ /* In SPT, This register is in Lan memory space,
+ * not flash. Therefore, only 32 bit access is
+ * supported
+ */
+ if (hw->mac.type == e1000_pch_spt)
+ ew32flash(ICH_FLASH_HSFSTS, hsflctl.regval << 16);
+ else
+ ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
+
+ ew32flash(ICH_FLASH_FADDR, flash_linear_addr);
+
+ ew32flash(ICH_FLASH_FDATA0, data);
+
+ /* check if FCERR is set to 1 , if set to 1, clear it
+ * and try the whole sequence a few more times else done
+ */
+ ret_val =
+ e1000_flash_cycle_ich8lan(hw,
+ ICH_FLASH_WRITE_COMMAND_TIMEOUT);
+
+ if (!ret_val)
+ break;
+
+ /* If we're here, then things are most likely
+ * completely hosed, but if the error condition
+ * is detected, it won't hurt to give it another
+ * try...ICH_FLASH_CYCLE_REPEAT_COUNT times.
+ */
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+
+ if (hsfsts.hsf_status.flcerr)
+ /* Repeat for some time before giving up. */
+ continue;
+ if (!hsfsts.hsf_status.flcdone) {
+ e_dbg("Timeout error - flash cycle did not complete.\n");
+ break;
+ }
+ } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
+
+ return ret_val;
+}
+
+/**
* e1000_write_flash_byte_ich8lan - Write a single byte to NVM
* @hw: pointer to the HW structure
* @offset: The index of the byte to read.
@@ -3656,6 +4210,40 @@
}
/**
+* e1000_retry_write_flash_dword_ich8lan - Writes a dword to NVM
+* @hw: pointer to the HW structure
+* @offset: The offset of the word to write.
+* @dword: The dword to write to the NVM.
+*
+* Writes a single dword to the NVM using the flash access registers.
+* Goes through a retry algorithm before giving up.
+**/
+static s32 e1000_retry_write_flash_dword_ich8lan(struct e1000_hw *hw,
+ u32 offset, u32 dword)
+{
+ s32 ret_val;
+ u16 program_retries;
+
+ /* Must convert word offset into bytes. */
+ offset <<= 1;
+ ret_val = e1000_write_flash_data32_ich8lan(hw, offset, dword);
+
+ if (!ret_val)
+ return ret_val;
+ for (program_retries = 0; program_retries < 100; program_retries++) {
+ e_dbg("Retrying Byte %8.8X at offset %u\n", dword, offset);
+ usleep_range(100, 200);
+ ret_val = e1000_write_flash_data32_ich8lan(hw, offset, dword);
+ if (!ret_val)
+ break;
+ }
+ if (program_retries == 100)
+ return -E1000_ERR_NVM;
+
+ return 0;
+}
+
+/**
* e1000_retry_write_flash_byte_ich8lan - Writes a single byte to NVM
* @hw: pointer to the HW structure
* @offset: The offset of the byte to write.
@@ -3759,9 +4347,18 @@
/* Write a value 11 (block Erase) in Flash
* Cycle field in hw flash control
*/
- hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
+ if (hw->mac.type == e1000_pch_spt)
+ hsflctl.regval =
+ er32flash(ICH_FLASH_HSFSTS) >> 16;
+ else
+ hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
+
hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE;
- ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
+ if (hw->mac.type == e1000_pch_spt)
+ ew32flash(ICH_FLASH_HSFSTS,
+ hsflctl.regval << 16);
+ else
+ ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
/* Write the last 24 bits of an index within the
* block into Flash Linear address field in Flash
@@ -4180,7 +4777,8 @@
ew32(RFCTL, reg);
/* Enable ECC on Lynxpoint */
- if (hw->mac.type == e1000_pch_lpt) {
+ if ((hw->mac.type == e1000_pch_lpt) ||
+ (hw->mac.type == e1000_pch_spt)) {
reg = er32(PBECCSTS);
reg |= E1000_PBECCSTS_ECC_ENABLE;
ew32(PBECCSTS, reg);
@@ -4583,7 +5181,8 @@
if ((device_id == E1000_DEV_ID_PCH_LPTLP_I218_LM) ||
(device_id == E1000_DEV_ID_PCH_LPTLP_I218_V) ||
(device_id == E1000_DEV_ID_PCH_I218_LM3) ||
- (device_id == E1000_DEV_ID_PCH_I218_V3)) {
+ (device_id == E1000_DEV_ID_PCH_I218_V3) ||
+ (hw->mac.type == e1000_pch_spt)) {
u32 fextnvm6 = er32(FEXTNVM6);
ew32(FEXTNVM6, fextnvm6 & ~E1000_FEXTNVM6_REQ_PLL_CLK);
@@ -5058,6 +5657,17 @@
.write = e1000_write_nvm_ich8lan,
};
+static const struct e1000_nvm_operations spt_nvm_ops = {
+ .acquire = e1000_acquire_nvm_ich8lan,
+ .release = e1000_release_nvm_ich8lan,
+ .read = e1000_read_nvm_spt,
+ .update = e1000_update_nvm_checksum_spt,
+ .reload = e1000e_reload_nvm_generic,
+ .valid_led_default = e1000_valid_led_default_ich8lan,
+ .validate = e1000_validate_nvm_checksum_ich8lan,
+ .write = e1000_write_nvm_ich8lan,
+};
+
const struct e1000_info e1000_ich8_info = {
.mac = e1000_ich8lan,
.flags = FLAG_HAS_WOL
@@ -5166,3 +5776,23 @@
.phy_ops = &ich8_phy_ops,
.nvm_ops = &ich8_nvm_ops,
};
+
+const struct e1000_info e1000_pch_spt_info = {
+ .mac = e1000_pch_spt,
+ .flags = FLAG_IS_ICH
+ | FLAG_HAS_WOL
+ | FLAG_HAS_HW_TIMESTAMP
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_AMT
+ | FLAG_HAS_FLASH
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_APME_IN_WUC,
+ .flags2 = FLAG2_HAS_PHY_STATS
+ | FLAG2_HAS_EEE,
+ .pba = 26,
+ .max_hw_frame_size = 9018,
+ .get_variants = e1000_get_variants_ich8lan,
+ .mac_ops = &ich8_mac_ops,
+ .phy_ops = &ich8_phy_ops,
+ .nvm_ops = &spt_nvm_ops,
+};
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.h b/drivers/net/ethernet/intel/e1000e/ich8lan.h
index 8066a49..770a573 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.h
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.h
@@ -95,9 +95,18 @@
#define E1000_FEXTNVM6_REQ_PLL_CLK 0x00000100
#define E1000_FEXTNVM6_ENABLE_K1_ENTRY_CONDITION 0x00000200
+#define E1000_FEXTNVM6_K1_OFF_ENABLE 0x80000000
+/* bit for disabling packet buffer read */
+#define E1000_FEXTNVM7_DISABLE_PB_READ 0x00040000
#define E1000_FEXTNVM7_DISABLE_SMB_PERST 0x00000020
+#define K1_ENTRY_LATENCY 0
+#define K1_MIN_TIME 1
+#define NVM_SIZE_MULTIPLIER 4096 /*multiplier for NVMS field */
+#define E1000_FLASH_BASE_ADDR 0xE000 /*offset of NVM access regs */
+#define E1000_CTRL_EXT_NVMVS 0x3 /*NVM valid sector */
+
#define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL
#define E1000_ICH_RAR_ENTRIES 7
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 1e8c40f..6fa4fc0 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -70,6 +70,7 @@
[board_pchlan] = &e1000_pch_info,
[board_pch2lan] = &e1000_pch2_info,
[board_pch_lpt] = &e1000_pch_lpt_info,
+ [board_pch_spt] = &e1000_pch_spt_info,
};
struct e1000_reg_info {
@@ -1796,7 +1797,8 @@
}
/* Reset on uncorrectable ECC error */
- if ((icr & E1000_ICR_ECCER) && (hw->mac.type == e1000_pch_lpt)) {
+ if ((icr & E1000_ICR_ECCER) && ((hw->mac.type == e1000_pch_lpt) ||
+ (hw->mac.type == e1000_pch_spt))) {
u32 pbeccsts = er32(PBECCSTS);
adapter->corr_errors +=
@@ -1876,7 +1878,8 @@
}
/* Reset on uncorrectable ECC error */
- if ((icr & E1000_ICR_ECCER) && (hw->mac.type == e1000_pch_lpt)) {
+ if ((icr & E1000_ICR_ECCER) && ((hw->mac.type == e1000_pch_lpt) ||
+ (hw->mac.type == e1000_pch_spt))) {
u32 pbeccsts = er32(PBECCSTS);
adapter->corr_errors +=
@@ -2257,7 +2260,8 @@
if (adapter->msix_entries) {
ew32(EIAC_82574, adapter->eiac_mask & E1000_EIAC_MASK_82574);
ew32(IMS, adapter->eiac_mask | E1000_IMS_OTHER | E1000_IMS_LSC);
- } else if (hw->mac.type == e1000_pch_lpt) {
+ } else if ((hw->mac.type == e1000_pch_lpt) ||
+ (hw->mac.type == e1000_pch_spt)) {
ew32(IMS, IMS_ENABLE_MASK | E1000_IMS_ECCER);
} else {
ew32(IMS, IMS_ENABLE_MASK);
@@ -3014,6 +3018,19 @@
ew32(TCTL, tctl);
hw->mac.ops.config_collision_dist(hw);
+
+ /* SPT Si errata workaround to avoid data corruption */
+ if (hw->mac.type == e1000_pch_spt) {
+ u32 reg_val;
+
+ reg_val = er32(IOSFPC);
+ reg_val |= E1000_RCTL_RDMTS_HEX;
+ ew32(IOSFPC, reg_val);
+
+ reg_val = er32(TARC(0));
+ reg_val |= E1000_TARC0_CB_MULTIQ_3_REQ;
+ ew32(TARC(0), reg_val);
+ }
}
/**
@@ -3490,8 +3507,11 @@
struct e1000_hw *hw = &adapter->hw;
u32 incvalue, incperiod, shift;
- /* Make sure clock is enabled on I217 before checking the frequency */
- if ((hw->mac.type == e1000_pch_lpt) &&
+ /* Make sure clock is enabled on I217/I218/I219 before checking
+ * the frequency
+ */
+ if (((hw->mac.type == e1000_pch_lpt) ||
+ (hw->mac.type == e1000_pch_spt)) &&
!(er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) &&
!(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_ENABLED)) {
u32 fextnvm7 = er32(FEXTNVM7);
@@ -3505,10 +3525,13 @@
switch (hw->mac.type) {
case e1000_pch2lan:
case e1000_pch_lpt:
- /* On I217, the clock frequency is 25MHz or 96MHz as
- * indicated by the System Clock Frequency Indication
+ case e1000_pch_spt:
+ /* On I217, I218 and I219, the clock frequency is 25MHz
+ * or 96MHz as indicated by the System Clock Frequency
+ * Indication
*/
- if ((hw->mac.type != e1000_pch_lpt) ||
+ if (((hw->mac.type != e1000_pch_lpt) &&
+ (hw->mac.type != e1000_pch_spt)) ||
(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI)) {
/* Stable 96MHz frequency */
incperiod = INCPERIOD_96MHz;
@@ -3875,6 +3898,7 @@
break;
case e1000_pch2lan:
case e1000_pch_lpt:
+ case e1000_pch_spt:
fc->refresh_time = 0x0400;
if (adapter->netdev->mtu <= ETH_DATA_LEN) {
@@ -4759,7 +4783,8 @@
adapter->stats.mgpdc += er32(MGTPDC);
/* Correctable ECC Errors */
- if (hw->mac.type == e1000_pch_lpt) {
+ if ((hw->mac.type == e1000_pch_lpt) ||
+ (hw->mac.type == e1000_pch_spt)) {
u32 pbeccsts = er32(PBECCSTS);
adapter->corr_errors +=
@@ -6144,7 +6169,8 @@
if (adapter->hw.phy.type == e1000_phy_igp_3) {
e1000e_igp3_phy_powerdown_workaround_ich8lan(&adapter->hw);
- } else if (hw->mac.type == e1000_pch_lpt) {
+ } else if ((hw->mac.type == e1000_pch_lpt) ||
+ (hw->mac.type == e1000_pch_spt)) {
if (!(wufc & (E1000_WUFC_EX | E1000_WUFC_MC | E1000_WUFC_BC)))
/* ULP does not support wake from unicast, multicast
* or broadcast.
@@ -7213,6 +7239,10 @@
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_V2), board_pch_lpt },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_LM3), board_pch_lpt },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_V3), board_pch_lpt },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM), board_pch_spt },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V), board_pch_spt },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM2), board_pch_spt },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V2), board_pch_spt },
{ 0, 0, 0, 0, 0, 0, 0 } /* terminate list */
};
diff --git a/drivers/net/ethernet/intel/e1000e/ptp.c b/drivers/net/ethernet/intel/e1000e/ptp.c
index 978ef9c..1490f1e 100644
--- a/drivers/net/ethernet/intel/e1000e/ptp.c
+++ b/drivers/net/ethernet/intel/e1000e/ptp.c
@@ -221,7 +221,9 @@
switch (hw->mac.type) {
case e1000_pch2lan:
case e1000_pch_lpt:
- if ((hw->mac.type != e1000_pch_lpt) ||
+ case e1000_pch_spt:
+ if (((hw->mac.type != e1000_pch_lpt) &&
+ (hw->mac.type != e1000_pch_spt)) ||
(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI)) {
adapter->ptp_clock_info.max_adj = 24000000 - 1;
break;
diff --git a/drivers/net/ethernet/intel/e1000e/regs.h b/drivers/net/ethernet/intel/e1000e/regs.h
index ea235bb..85eefc4 100644
--- a/drivers/net/ethernet/intel/e1000e/regs.h
+++ b/drivers/net/ethernet/intel/e1000e/regs.h
@@ -38,6 +38,7 @@
#define E1000_FEXTNVM4 0x00024 /* Future Extended NVM 4 - RW */
#define E1000_FEXTNVM6 0x00010 /* Future Extended NVM 6 - RW */
#define E1000_FEXTNVM7 0x000E4 /* Future Extended NVM 7 - RW */
+#define E1000_PCIEANACFG 0x00F18 /* PCIE Analog Config */
#define E1000_FCT 0x00030 /* Flow Control Type - RW */
#define E1000_VET 0x00038 /* VLAN Ether Type - RW */
#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */
@@ -67,6 +68,7 @@
#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
#define E1000_PBS 0x01008 /* Packet Buffer Size */
#define E1000_PBECCSTS 0x0100C /* Packet Buffer ECC Status - RW */
+#define E1000_IOSFPC 0x00F28 /* TX corrupted data */
#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */
#define E1000_FLOP 0x0103C /* FLASH Opcode Register */
@@ -121,6 +123,7 @@
(0x054E4 + ((_i - 16) * 8)))
#define E1000_SHRAL(_i) (0x05438 + ((_i) * 8))
#define E1000_SHRAH(_i) (0x0543C + ((_i) * 8))
+#define E1000_TARC0_CB_MULTIQ_3_REQ (1 << 28 | 1 << 29)
#define E1000_TDFH 0x03410 /* Tx Data FIFO Head - RW */
#define E1000_TDFT 0x03418 /* Tx Data FIFO Tail - RW */
#define E1000_TDFHS 0x03420 /* Tx Data FIFO Head Saved - RW */