bdi: allow block devices to say that they require stable page writes
This patchset ("stable page writes, part 2") makes some key
modifications to the original 'stable page writes' patchset. First, it
provides creators (devices and filesystems) of a backing_dev_info a flag
that declares whether or not it is necessary to ensure that page
contents cannot change during writeout. It is no longer assumed that
this is true of all devices (which was never true anyway). Second, the
flag is used to relaxed the wait_on_page_writeback calls so that wait
only occurs if the device needs it. Third, it fixes up the remaining
disk-backed filesystems to use this improved conditional-wait logic to
provide stable page writes on those filesystems.
It is hoped that (for people not using checksumming devices, anyway)
this patchset will give back unnecessary performance decreases since the
original stable page write patchset went into 3.0. Sorry about not
fixing it sooner.
Complaints were registered by several people about the long write
latencies introduced by the original stable page write patchset.
Generally speaking, the kernel ought to allocate as little extra memory
as possible to facilitate writeout, but for people who simply cannot
wait, a second page stability strategy is (re)introduced: snapshotting
page contents. The waiting behavior is still the default strategy; to
enable page snapshotting, a superblock flag (MS_SNAP_STABLE) must be
set. This flag is used to bandaid^Henable stable page writeback on
ext3[1], and is not used anywhere else.
Given that there are already a few storage devices and network FSes that
have rolled their own page stability wait/page snapshot code, it would
be nice to move towards consolidating all of these. It seems possible
that iscsi and raid5 may wish to use the new stable page write support
to enable zero-copy writeout.
Thank you to Jan Kara for helping fix a couple more filesystems.
Per Andrew Morton's request, here are the result of using dbench to measure
latencies on ext2:
3.8.0-rc3:
Operation Count AvgLat MaxLat
----------------------------------------
WriteX 109347 0.028 59.817
ReadX 347180 0.004 3.391
Flush 15514 29.828 287.283
Throughput 57.429 MB/sec 4 clients 4 procs max_latency=287.290 ms
3.8.0-rc3 + patches:
WriteX 105556 0.029 4.273
ReadX 335004 0.005 4.112
Flush 14982 30.540 298.634
Throughput 55.4496 MB/sec 4 clients 4 procs max_latency=298.650 ms
As you can see, for ext2 the maximum write latency decreases from ~60ms
on a laptop hard disk to ~4ms. I'm not sure why the flush latencies
increase, though I suspect that being able to dirty pages faster gives
the flusher more work to do.
On ext4, the average write latency decreases as well as all the maximum
latencies:
3.8.0-rc3:
WriteX 85624 0.152 33.078
ReadX 272090 0.010 61.210
Flush 12129 36.219 168.260
Throughput 44.8618 MB/sec 4 clients 4 procs max_latency=168.276 ms
3.8.0-rc3 + patches:
WriteX 86082 0.141 30.928
ReadX 273358 0.010 36.124
Flush 12214 34.800 165.689
Throughput 44.9941 MB/sec 4 clients 4 procs max_latency=165.722 ms
XFS seems to exhibit similar latency improvements as ext2:
3.8.0-rc3:
WriteX 125739 0.028 104.343
ReadX 399070 0.005 4.115
Flush 17851 25.004 131.390
Throughput 66.0024 MB/sec 4 clients 4 procs max_latency=131.406 ms
3.8.0-rc3 + patches:
WriteX 123529 0.028 6.299
ReadX 392434 0.005 4.287
Flush 17549 25.120 188.687
Throughput 64.9113 MB/sec 4 clients 4 procs max_latency=188.704 ms
...and btrfs, just to round things out, also shows some latency
decreases:
3.8.0-rc3:
WriteX 67122 0.083 82.355
ReadX 212719 0.005 2.828
Flush 9547 47.561 147.418
Throughput 35.3391 MB/sec 4 clients 4 procs max_latency=147.433 ms
3.8.0-rc3 + patches:
WriteX 64898 0.101 71.631
ReadX 206673 0.005 7.123
Flush 9190 47.963 219.034
Throughput 34.0795 MB/sec 4 clients 4 procs max_latency=219.044 ms
Before this patchset, all filesystems would block, regardless of whether
or not it was necessary. ext3 would wait, but still generate occasional
checksum errors. The network filesystems were left to do their own
thing, so they'd wait too.
After this patchset, all the disk filesystems except ext3 and btrfs will
wait only if the hardware requires it. ext3 (if necessary) snapshots
pages instead of blocking, and btrfs provides its own bdi so the mm will
never wait. Network filesystems haven't been touched, so either they
provide their own wait code, or they don't block at all. The blocking
behavior is back to what it was before 3.0 if you don't have a disk
requiring stable page writes.
This patchset has been tested on 3.8.0-rc3 on x64 with ext3, ext4, and
xfs. I've spot-checked 3.8.0-rc4 and seem to be getting the same
results as -rc3.
[1] The alternative fixes to ext3 include fixing the locking order and
page bit handling like we did for ext4 (but then why not just use
ext4?), or setting PG_writeback so early that ext3 becomes extremely
slow. I tried that, but the number of write()s I could initiate dropped
by nearly an order of magnitude. That was a bit much even for the
author of the stable page series! :)
This patch:
Creates a per-backing-device flag that tracks whether or not pages must
be held immutable during writeout. Eventually it will be used to waive
wait_for_page_writeback() if nothing requires stable pages.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
4 files changed