diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt
new file mode 100644
index 0000000..52916b4
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/gic.txt
@@ -0,0 +1,55 @@
+* ARM Generic Interrupt Controller
+
+ARM SMP cores are often associated with a GIC, providing per processor
+interrupts (PPI), shared processor interrupts (SPI) and software
+generated interrupts (SGI).
+
+Primary GIC is attached directly to the CPU and typically has PPIs and SGIs.
+Secondary GICs are cascaded into the upward interrupt controller and do not
+have PPIs or SGIs.
+
+Main node required properties:
+
+- compatible : should be one of:
+	"arm,cortex-a9-gic"
+	"arm,arm11mp-gic"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source.  The type shall be a <u32> and the value shall be 3.
+
+  The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI
+  interrupts.
+
+  The 2nd cell contains the interrupt number for the interrupt type.
+  SPI interrupts are in the range [0-987].  PPI interrupts are in the
+  range [0-15].
+
+  The 3rd cell is the flags, encoded as follows:
+	bits[3:0] trigger type and level flags.
+		1 = low-to-high edge triggered
+		2 = high-to-low edge triggered
+		4 = active high level-sensitive
+		8 = active low level-sensitive
+	bits[15:8] PPI interrupt cpu mask.  Each bit corresponds to each of
+	the 8 possible cpus attached to the GIC.  A bit set to '1' indicated
+	the interrupt is wired to that CPU.  Only valid for PPI interrupts.
+
+- reg : Specifies base physical address(s) and size of the GIC registers. The
+  first region is the GIC distributor register base and size. The 2nd region is
+  the GIC cpu interface register base and size.
+
+Optional
+- interrupts	: Interrupt source of the parent interrupt controller. Only
+  present on secondary GICs.
+
+Example:
+
+	intc: interrupt-controller@fff11000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <1>;
+		interrupt-controller;
+		reg = <0xfff11000 0x1000>,
+		      <0xfff10100 0x100>;
+	};
+
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 3bf38c8..a94a09b 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -29,6 +29,7 @@
 	select HAVE_GENERIC_HARDIRQS
 	select HAVE_SPARSE_IRQ
 	select GENERIC_IRQ_SHOW
+	select CPU_PM if (SUSPEND || CPU_IDLE)
 	help
 	  The ARM series is a line of low-power-consumption RISC chip designs
 	  licensed by ARM Ltd and targeted at embedded applications and
@@ -195,7 +196,8 @@
 	  The base address of exception vectors.
 
 config ARM_PATCH_PHYS_VIRT
-	bool "Patch physical to virtual translations at runtime"
+	bool "Patch physical to virtual translations at runtime" if EMBEDDED
+	default y
 	depends on !XIP_KERNEL && MMU
 	depends on !ARCH_REALVIEW || !SPARSEMEM
 	help
@@ -204,16 +206,25 @@
 	  kernel in system memory.
 
 	  This can only be used with non-XIP MMU kernels where the base
-	  of physical memory is at a 16MB boundary, or theoretically 64K
-	  for the MSM machine class.
+	  of physical memory is at a 16MB boundary.
 
-config ARM_PATCH_PHYS_VIRT_16BIT
-	def_bool y
-	depends on ARM_PATCH_PHYS_VIRT && ARCH_MSM
+	  Only disable this option if you know that you do not require
+	  this feature (eg, building a kernel for a single machine) and
+	  you need to shrink the kernel to the minimal size.
+
+config NEED_MACH_MEMORY_H
+	bool
 	help
-	  This option extends the physical to virtual translation patching
-	  to allow physical memory down to a theoretical minimum of 64K
-	  boundaries.
+	  Select this when mach/memory.h is required to provide special
+	  definitions for this platform.  The need for mach/memory.h should
+	  be avoided when possible.
+
+config PHYS_OFFSET
+	hex "Physical address of main memory"
+	depends on !ARM_PATCH_PHYS_VIRT && !NEED_MACH_MEMORY_H
+	help
+	  Please provide the physical address corresponding to the
+	  location of main memory in your system.
 
 source "init/Kconfig"
 
@@ -246,6 +257,7 @@
 	select GENERIC_CLOCKEVENTS
 	select PLAT_VERSATILE
 	select PLAT_VERSATILE_FPGA_IRQ
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for ARM's Integrator platform.
 
@@ -261,6 +273,7 @@
 	select PLAT_VERSATILE_CLCD
 	select ARM_TIMER_SP804
 	select GPIO_PL061 if GPIOLIB
+	select NEED_MACH_MEMORY_H
 	help
 	  This enables support for ARM Ltd RealView boards.
 
@@ -301,7 +314,6 @@
 	select ARCH_REQUIRE_GPIOLIB
 	select HAVE_CLK
 	select CLKDEV_LOOKUP
-	select ARM_PATCH_PHYS_VIRT if MMU
 	help
 	  This enables support for systems based on the Atmel AT91RM9200,
 	  AT91SAM9 and AT91CAP9 processors.
@@ -322,6 +334,7 @@
 	bool "Cirrus Logic CLPS711x/EP721x-based"
 	select CPU_ARM720T
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Cirrus Logic 711x/721x based boards.
 
@@ -362,6 +375,7 @@
 	select ISA
 	select NO_IOPORT
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  This is an evaluation board for the StrongARM processor available
 	  from Digital. It has limited hardware on-board, including an
@@ -377,6 +391,7 @@
 	select ARCH_REQUIRE_GPIOLIB
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MEMORY_H
 	help
 	  This enables support for the Cirrus EP93xx series of CPUs.
 
@@ -385,6 +400,7 @@
 	select CPU_SA110
 	select FOOTBRIDGE
 	select GENERIC_CLOCKEVENTS
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for systems based on the DC21285 companion chip
 	  ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
@@ -435,6 +451,7 @@
 	select PCI
 	select ARCH_SUPPORTS_MSI
 	select VMSPLIT_1G
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Intel's IOP13XX (XScale) family of processors.
 
@@ -465,6 +482,7 @@
 	select CPU_XSC3
  	select PCI
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Intel's IXP23xx (XScale) family of processors.
 
@@ -474,6 +492,7 @@
 	select CPU_XSCALE
 	select PCI
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Intel's IXP2400/2800 (XScale) family of processors.
 
@@ -567,6 +586,7 @@
 	select CPU_ARM922T
 	select ARCH_REQUIRE_GPIOLIB
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based
 	  System-on-Chip devices.
@@ -658,6 +678,7 @@
 	select SPARSE_IRQ
 	select MULTI_IRQ_HANDLER
 	select PM_GENERIC_DOMAINS if PM
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Renesas's SH-Mobile and R-Mobile ARM platforms.
 
@@ -672,6 +693,7 @@
 	select NO_IOPORT
 	select ARCH_SPARSEMEM_ENABLE
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  On the Acorn Risc-PC, Linux can support the internal IDE disk and
 	  CD-ROM interface, serial and parallel port, and the floppy drive.
@@ -690,6 +712,7 @@
 	select HAVE_SCHED_CLOCK
 	select TICK_ONESHOT
 	select ARCH_REQUIRE_GPIOLIB
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for StrongARM 11x0 based boards.
 
@@ -782,6 +805,7 @@
 	select HAVE_S3C2410_I2C if I2C
 	select HAVE_S3C_RTC if RTC_CLASS
 	select HAVE_S3C2410_WATCHDOG if WATCHDOG
+	select NEED_MACH_MEMORY_H
 	help
 	  Samsung S5PV210/S5PC110 series based systems
 
@@ -798,6 +822,7 @@
 	select HAVE_S3C_RTC if RTC_CLASS
 	select HAVE_S3C2410_I2C if I2C
 	select HAVE_S3C2410_WATCHDOG if WATCHDOG
+	select NEED_MACH_MEMORY_H
 	help
 	  Samsung EXYNOS4 series based systems
 
@@ -809,6 +834,7 @@
 	select ZONE_DMA
 	select PCI
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for the StrongARM based Digital DNARD machine, also known
 	  as "Shark" (<http://www.shark-linux.de/shark.html>).
@@ -836,6 +862,7 @@
 	select CLKDEV_LOOKUP
 	select HAVE_MACH_CLKDEV
 	select GENERIC_GPIO
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for ST-Ericsson U300 series mobile platforms.
 
@@ -1408,6 +1435,31 @@
 
 	  If you don't know what to do here, say Y.
 
+config ARM_CPU_TOPOLOGY
+	bool "Support cpu topology definition"
+	depends on SMP && CPU_V7
+	default y
+	help
+	  Support ARM cpu topology definition. The MPIDR register defines
+	  affinity between processors which is then used to describe the cpu
+	  topology of an ARM System.
+
+config SCHED_MC
+	bool "Multi-core scheduler support"
+	depends on ARM_CPU_TOPOLOGY
+	help
+	  Multi-core scheduler support improves the CPU scheduler's decision
+	  making when dealing with multi-core CPU chips at a cost of slightly
+	  increased overhead in some places. If unsure say N here.
+
+config SCHED_SMT
+	bool "SMT scheduler support"
+	depends on ARM_CPU_TOPOLOGY
+	help
+	  Improves the CPU scheduler's decision making when dealing with
+	  MultiThreading at a cost of slightly increased overhead in some
+	  places. If unsure say N here.
+
 config HAVE_ARM_SCU
 	bool
 	help
@@ -1808,6 +1860,38 @@
 
 endchoice
 
+config ARM_APPENDED_DTB
+	bool "Use appended device tree blob to zImage (EXPERIMENTAL)"
+	depends on OF && !ZBOOT_ROM && EXPERIMENTAL
+	help
+	  With this option, the boot code will look for a device tree binary
+	  (DTB) appended to zImage
+	  (e.g. cat zImage <filename>.dtb > zImage_w_dtb).
+
+	  This is meant as a backward compatibility convenience for those
+	  systems with a bootloader that can't be upgraded to accommodate
+	  the documented boot protocol using a device tree.
+
+	  Beware that there is very little in terms of protection against
+	  this option being confused by leftover garbage in memory that might
+	  look like a DTB header after a reboot if no actual DTB is appended
+	  to zImage.  Do not leave this option active in a production kernel
+	  if you don't intend to always append a DTB.  Proper passing of the
+	  location into r2 of a bootloader provided DTB is always preferable
+	  to this option.
+
+config ARM_ATAG_DTB_COMPAT
+	bool "Supplement the appended DTB with traditional ATAG information"
+	depends on ARM_APPENDED_DTB
+	help
+	  Some old bootloaders can't be updated to a DTB capable one, yet
+	  they provide ATAGs with memory configuration, the ramdisk address,
+	  the kernel cmdline string, etc.  Such information is dynamically
+	  provided by the bootloader and can't always be stored in a static
+	  DTB.  To allow a device tree enabled kernel to be used with such
+	  bootloaders, this option allows zImage to extract the information
+	  from the ATAG list and store it at run time into the appended DTB.
+
 config CMDLINE
 	string "Default kernel command string"
 	default ""
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 81cbe40..0887801 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -65,13 +65,71 @@
 
 # These options are only for real kernel hackers who want to get their hands dirty.
 config DEBUG_LL
-	bool "Kernel low-level debugging functions"
+	bool "Kernel low-level debugging functions (read help!)"
 	depends on DEBUG_KERNEL
 	help
 	  Say Y here to include definitions of printascii, printch, printhex
 	  in the kernel.  This is helpful if you are debugging code that
 	  executes before the console is initialized.
 
+	  Note that selecting this option will limit the kernel to a single
+	  UART definition, as specified below. Attempting to boot the kernel
+	  image on a different platform *will not work*, so this option should
+	  not be enabled for kernels that are intended to be portable.
+
+choice
+	prompt "Kernel low-level debugging port"
+	depends on DEBUG_LL
+
+	config DEBUG_LL_UART_NONE
+		bool "No low-level debugging UART"
+		help
+		  Say Y here if your platform doesn't provide a UART option
+		  below. This relies on your platform choosing the right UART
+		  definition internally in order for low-level debugging to
+		  work.
+
+	config DEBUG_ICEDCC
+		bool "Kernel low-level debugging via EmbeddedICE DCC channel"
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the EmbeddedICE macrocell's DCC channel using
+		  co-processor 14. This is known to work on the ARM9 style ICE
+		  channel and on the XScale with the PEEDI.
+
+		  Note that the system will appear to hang during boot if there
+		  is nothing connected to read from the DCC.
+
+	config DEBUG_FOOTBRIDGE_COM1
+		bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1"
+		depends on FOOTBRIDGE
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the 8250 at PCI COM1.
+
+	config DEBUG_DC21285_PORT
+		bool "Kernel low-level debugging messages via footbridge serial port"
+		depends on FOOTBRIDGE
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the serial port in the DC21285 (Footbridge).
+
+	config DEBUG_CLPS711X_UART1
+		bool "Kernel low-level debugging messages via UART1"
+		depends on ARCH_CLPS711X
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the first serial port on these devices.
+
+	config DEBUG_CLPS711X_UART2
+		bool "Kernel low-level debugging messages via UART2"
+		depends on ARCH_CLPS711X
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the second serial port on these devices.
+
+endchoice
+
 config EARLY_PRINTK
 	bool "Early printk"
 	depends on DEBUG_LL
@@ -80,18 +138,6 @@
 	  kernel low-level debugging functions. Add earlyprintk to your
 	  kernel parameters to enable this console.
 
-config DEBUG_ICEDCC
-	bool "Kernel low-level debugging via EmbeddedICE DCC channel"
-	depends on DEBUG_LL
-	help
-	  Say Y here if you want the debug print routines to direct their
-	  output to the EmbeddedICE macrocell's DCC channel using
-	  co-processor 14. This is known to work on the ARM9 style ICE
-	  channel and on the XScale with the PEEDI.
-
-	  It does include a timeout to ensure that the system does not
-	  totally freeze when there is nothing connected to read.
-
 config OC_ETM
 	bool "On-chip ETM and ETB"
 	select ARM_AMBA
@@ -100,23 +146,6 @@
 	  buffer driver that will allow you to collect traces of the
 	  kernel code.
 
-config DEBUG_DC21285_PORT
-	bool "Kernel low-level debugging messages via footbridge serial port"
-	depends on DEBUG_LL && FOOTBRIDGE
-	help
-	  Say Y here if you want the debug print routines to direct their
-	  output to the serial port in the DC21285 (Footbridge). Saying N
-	  will cause the debug messages to appear on the first 16550
-	  serial port.
-
-config DEBUG_CLPS711X_UART2
-	bool "Kernel low-level debugging messages via UART2"
-	depends on DEBUG_LL && ARCH_CLPS711X
-	help
-	  Say Y here if you want the debug print routines to direct their
-	  output to the second serial port on these devices.  Saying N will
-	  cause the debug messages to appear on the first serial port.
-
 config DEBUG_S3C_UART
 	depends on PLAT_SAMSUNG
 	int "S3C UART to use for low-level debug"
@@ -129,4 +158,10 @@
 	  The uncompressor code port configuration is now handled
 	  by CONFIG_S3C_LOWLEVEL_UART_PORT.
 
+config ARM_KPROBES_TEST
+	tristate "Kprobes test module"
+	depends on KPROBES && MODULES
+	help
+	  Perform tests of kprobes API and instruction set simulation.
+
 endmenu
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 9260c29..8904caa 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -128,6 +128,9 @@
 ifeq ($(CONFIG_ARCH_SA1100),y)
 textofs-$(CONFIG_SA1111) := 0x00208000
 endif
+textofs-$(CONFIG_ARCH_MSM7X30) := 0x00208000
+textofs-$(CONFIG_ARCH_MSM8X60) := 0x00208000
+textofs-$(CONFIG_ARCH_MSM8960) := 0x00208000
 
 # Machine directory name.  This list is sorted alphanumerically
 # by CONFIG_* macro name.
diff --git a/arch/arm/boot/compressed/.gitignore b/arch/arm/boot/compressed/.gitignore
index c602896..e0936a1 100644
--- a/arch/arm/boot/compressed/.gitignore
+++ b/arch/arm/boot/compressed/.gitignore
@@ -5,3 +5,12 @@
 piggy.lzma
 vmlinux
 vmlinux.lds
+
+# borrowed libfdt files
+fdt.c
+fdt.h
+fdt_ro.c
+fdt_rw.c
+fdt_wip.c
+libfdt.h
+libfdt_internal.h
diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile
index 0c74a6f..e4f32a8 100644
--- a/arch/arm/boot/compressed/Makefile
+++ b/arch/arm/boot/compressed/Makefile
@@ -26,6 +26,10 @@
 OBJS	+= misc.o decompress.o
 FONTC	= $(srctree)/drivers/video/console/font_acorn_8x8.c
 
+# string library code (-Os is enforced to keep it much smaller)
+OBJS		+= string.o
+CFLAGS_string.o	:= -Os
+
 #
 # Architecture dependencies
 #
@@ -89,21 +93,41 @@
 suffix_$(CONFIG_KERNEL_LZO)  = lzo
 suffix_$(CONFIG_KERNEL_LZMA) = lzma
 
+# Borrowed libfdt files for the ATAG compatibility mode
+
+libfdt		:= fdt_rw.c fdt_ro.c fdt_wip.c fdt.c
+libfdt_hdrs	:= fdt.h libfdt.h libfdt_internal.h
+
+libfdt_objs	:= $(addsuffix .o, $(basename $(libfdt)))
+
+$(addprefix $(obj)/,$(libfdt) $(libfdt_hdrs)): $(obj)/%: $(srctree)/scripts/dtc/libfdt/%
+	$(call cmd,shipped)
+
+$(addprefix $(obj)/,$(libfdt_objs) atags_to_fdt.o): \
+	$(addprefix $(obj)/,$(libfdt_hdrs))
+
+ifeq ($(CONFIG_ARM_ATAG_DTB_COMPAT),y)
+OBJS	+= $(libfdt_objs) atags_to_fdt.o
+endif
+
 targets       := vmlinux vmlinux.lds \
 		 piggy.$(suffix_y) piggy.$(suffix_y).o \
-		 font.o font.c head.o misc.o $(OBJS)
+		 lib1funcs.o lib1funcs.S font.o font.c head.o misc.o $(OBJS)
 
 # Make sure files are removed during clean
-extra-y       += piggy.gzip piggy.lzo piggy.lzma lib1funcs.S
+extra-y       += piggy.gzip piggy.lzo piggy.lzma lib1funcs.S $(libfdt) $(libfdt_hdrs)
 
 ifeq ($(CONFIG_FUNCTION_TRACER),y)
 ORIG_CFLAGS := $(KBUILD_CFLAGS)
 KBUILD_CFLAGS = $(subst -pg, , $(ORIG_CFLAGS))
 endif
 
-ccflags-y := -fpic -fno-builtin
+ccflags-y := -fpic -fno-builtin -I$(obj)
 asflags-y := -Wa,-march=all
 
+# Supply kernel BSS size to the decompressor via a linker symbol.
+KBSS_SZ = $(shell size $(obj)/../../../../vmlinux | awk 'END{print $$3}')
+LDFLAGS_vmlinux = --defsym _kernel_bss_size=$(KBSS_SZ)
 # Supply ZRELADDR to the decompressor via a linker symbol.
 ifneq ($(CONFIG_AUTO_ZRELADDR),y)
 LDFLAGS_vmlinux += --defsym zreladdr=$(ZRELADDR)
@@ -123,7 +147,7 @@
 # For __aeabi_uidivmod
 lib1funcs = $(obj)/lib1funcs.o
 
-$(obj)/lib1funcs.S: $(srctree)/arch/$(SRCARCH)/lib/lib1funcs.S FORCE
+$(obj)/lib1funcs.S: $(srctree)/arch/$(SRCARCH)/lib/lib1funcs.S
 	$(call cmd,shipped)
 
 # We need to prevent any GOTOFF relocs being used with references
diff --git a/arch/arm/boot/compressed/atags_to_fdt.c b/arch/arm/boot/compressed/atags_to_fdt.c
new file mode 100644
index 0000000..6ce11c4
--- /dev/null
+++ b/arch/arm/boot/compressed/atags_to_fdt.c
@@ -0,0 +1,97 @@
+#include <asm/setup.h>
+#include <libfdt.h>
+
+static int node_offset(void *fdt, const char *node_path)
+{
+	int offset = fdt_path_offset(fdt, node_path);
+	if (offset == -FDT_ERR_NOTFOUND)
+		offset = fdt_add_subnode(fdt, 0, node_path);
+	return offset;
+}
+
+static int setprop(void *fdt, const char *node_path, const char *property,
+		   uint32_t *val_array, int size)
+{
+	int offset = node_offset(fdt, node_path);
+	if (offset < 0)
+		return offset;
+	return fdt_setprop(fdt, offset, property, val_array, size);
+}
+
+static int setprop_string(void *fdt, const char *node_path,
+			  const char *property, const char *string)
+{
+	int offset = node_offset(fdt, node_path);
+	if (offset < 0)
+		return offset;
+	return fdt_setprop_string(fdt, offset, property, string);
+}
+
+static int setprop_cell(void *fdt, const char *node_path,
+			const char *property, uint32_t val)
+{
+	int offset = node_offset(fdt, node_path);
+	if (offset < 0)
+		return offset;
+	return fdt_setprop_cell(fdt, offset, property, val);
+}
+
+/*
+ * Convert and fold provided ATAGs into the provided FDT.
+ *
+ * REturn values:
+ *    = 0 -> pretend success
+ *    = 1 -> bad ATAG (may retry with another possible ATAG pointer)
+ *    < 0 -> error from libfdt
+ */
+int atags_to_fdt(void *atag_list, void *fdt, int total_space)
+{
+	struct tag *atag = atag_list;
+	uint32_t mem_reg_property[2 * NR_BANKS];
+	int memcount = 0;
+	int ret;
+
+	/* make sure we've got an aligned pointer */
+	if ((u32)atag_list & 0x3)
+		return 1;
+
+	/* if we get a DTB here we're done already */
+	if (*(u32 *)atag_list == fdt32_to_cpu(FDT_MAGIC))
+	       return 0;
+
+	/* validate the ATAG */
+	if (atag->hdr.tag != ATAG_CORE ||
+	    (atag->hdr.size != tag_size(tag_core) &&
+	     atag->hdr.size != 2))
+		return 1;
+
+	/* let's give it all the room it could need */
+	ret = fdt_open_into(fdt, fdt, total_space);
+	if (ret < 0)
+		return ret;
+
+	for_each_tag(atag, atag_list) {
+		if (atag->hdr.tag == ATAG_CMDLINE) {
+			setprop_string(fdt, "/chosen", "bootargs",
+					atag->u.cmdline.cmdline);
+		} else if (atag->hdr.tag == ATAG_MEM) {
+			if (memcount >= sizeof(mem_reg_property)/4)
+				continue;
+			mem_reg_property[memcount++] = cpu_to_fdt32(atag->u.mem.start);
+			mem_reg_property[memcount++] = cpu_to_fdt32(atag->u.mem.size);
+		} else if (atag->hdr.tag == ATAG_INITRD2) {
+			uint32_t initrd_start, initrd_size;
+			initrd_start = atag->u.initrd.start;
+			initrd_size = atag->u.initrd.size;
+			setprop_cell(fdt, "/chosen", "linux,initrd-start",
+					initrd_start);
+			setprop_cell(fdt, "/chosen", "linux,initrd-end",
+					initrd_start + initrd_size);
+		}
+	}
+
+	if (memcount)
+		setprop(fdt, "/memory", "reg", mem_reg_property, 4*memcount);
+
+	return fdt_pack(fdt);
+}
diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index e95a598..9f5ac11 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -216,6 +216,103 @@
 		mov	r10, r6
 #endif
 
+		mov	r5, #0			@ init dtb size to 0
+#ifdef CONFIG_ARM_APPENDED_DTB
+/*
+ *   r0  = delta
+ *   r2  = BSS start
+ *   r3  = BSS end
+ *   r4  = final kernel address
+ *   r5  = appended dtb size (still unknown)
+ *   r6  = _edata
+ *   r7  = architecture ID
+ *   r8  = atags/device tree pointer
+ *   r9  = size of decompressed image
+ *   r10 = end of this image, including  bss/stack/malloc space if non XIP
+ *   r11 = GOT start
+ *   r12 = GOT end
+ *   sp  = stack pointer
+ *
+ * if there are device trees (dtb) appended to zImage, advance r10 so that the
+ * dtb data will get relocated along with the kernel if necessary.
+ */
+
+		ldr	lr, [r6, #0]
+#ifndef __ARMEB__
+		ldr	r1, =0xedfe0dd0		@ sig is 0xd00dfeed big endian
+#else
+		ldr	r1, =0xd00dfeed
+#endif
+		cmp	lr, r1
+		bne	dtb_check_done		@ not found
+
+#ifdef CONFIG_ARM_ATAG_DTB_COMPAT
+		/*
+		 * OK... Let's do some funky business here.
+		 * If we do have a DTB appended to zImage, and we do have
+		 * an ATAG list around, we want the later to be translated
+		 * and folded into the former here.  To be on the safe side,
+		 * let's temporarily move  the stack away into the malloc
+		 * area.  No GOT fixup has occurred yet, but none of the
+		 * code we're about to call uses any global variable.
+		*/
+		add	sp, sp, #0x10000
+		stmfd	sp!, {r0-r3, ip, lr}
+		mov	r0, r8
+		mov	r1, r6
+		sub	r2, sp, r6
+		bl	atags_to_fdt
+
+		/*
+		 * If returned value is 1, there is no ATAG at the location
+		 * pointed by r8.  Try the typical 0x100 offset from start
+		 * of RAM and hope for the best.
+		 */
+		cmp	r0, #1
+		sub	r0, r4, #(TEXT_OFFSET - 0x100)
+		mov	r1, r6
+		sub	r2, sp, r6
+		blne	atags_to_fdt
+
+		ldmfd	sp!, {r0-r3, ip, lr}
+		sub	sp, sp, #0x10000
+#endif
+
+		mov	r8, r6			@ use the appended device tree
+
+		/*
+		 * Make sure that the DTB doesn't end up in the final
+		 * kernel's .bss area. To do so, we adjust the decompressed
+		 * kernel size to compensate if that .bss size is larger
+		 * than the relocated code.
+		 */
+		ldr	r5, =_kernel_bss_size
+		adr	r1, wont_overwrite
+		sub	r1, r6, r1
+		subs	r1, r5, r1
+		addhi	r9, r9, r1
+
+		/* Get the dtb's size */
+		ldr	r5, [r6, #4]
+#ifndef __ARMEB__
+		/* convert r5 (dtb size) to little endian */
+		eor	r1, r5, r5, ror #16
+		bic	r1, r1, #0x00ff0000
+		mov	r5, r5, ror #8
+		eor	r5, r5, r1, lsr #8
+#endif
+
+		/* preserve 64-bit alignment */
+		add	r5, r5, #7
+		bic	r5, r5, #7
+
+		/* relocate some pointers past the appended dtb */
+		add	r6, r6, r5
+		add	r10, r10, r5
+		add	sp, sp, r5
+dtb_check_done:
+#endif
+
 /*
  * Check to see if we will overwrite ourselves.
  *   r4  = final kernel address
@@ -223,15 +320,14 @@
  *   r10 = end of this image, including  bss/stack/malloc space if non XIP
  * We basically want:
  *   r4 - 16k page directory >= r10 -> OK
- *   r4 + image length <= current position (pc) -> OK
+ *   r4 + image length <= address of wont_overwrite -> OK
  */
 		add	r10, r10, #16384
 		cmp	r4, r10
 		bhs	wont_overwrite
 		add	r10, r4, r9
-   ARM(		cmp	r10, pc		)
- THUMB(		mov	lr, pc		)
- THUMB(		cmp	r10, lr		)
+		adr	r9, wont_overwrite
+		cmp	r10, r9
 		bls	wont_overwrite
 
 /*
@@ -285,14 +381,16 @@
  *   r2  = BSS start
  *   r3  = BSS end
  *   r4  = kernel execution address
+ *   r5  = appended dtb size (0 if not present)
  *   r7  = architecture ID
  *   r8  = atags pointer
  *   r11 = GOT start
  *   r12 = GOT end
  *   sp  = stack pointer
  */
-		teq	r0, #0
+		orrs	r1, r0, r5
 		beq	not_relocated
+
 		add	r11, r11, r0
 		add	r12, r12, r0
 
@@ -307,12 +405,21 @@
 
 		/*
 		 * Relocate all entries in the GOT table.
+		 * Bump bss entries to _edata + dtb size
 		 */
 1:		ldr	r1, [r11, #0]		@ relocate entries in the GOT
-		add	r1, r1, r0		@ table.  This fixes up the
-		str	r1, [r11], #4		@ C references.
+		add	r1, r1, r0		@ This fixes up C references
+		cmp	r1, r2			@ if entry >= bss_start &&
+		cmphs	r3, r1			@       bss_end > entry
+		addhi	r1, r1, r5		@    entry += dtb size
+		str	r1, [r11], #4		@ next entry
 		cmp	r11, r12
 		blo	1b
+
+		/* bump our bss pointers too */
+		add	r2, r2, r5
+		add	r3, r3, r5
+
 #else
 
 		/*
diff --git a/arch/arm/boot/compressed/libfdt_env.h b/arch/arm/boot/compressed/libfdt_env.h
new file mode 100644
index 0000000..1f4e718
--- /dev/null
+++ b/arch/arm/boot/compressed/libfdt_env.h
@@ -0,0 +1,15 @@
+#ifndef _ARM_LIBFDT_ENV_H
+#define _ARM_LIBFDT_ENV_H
+
+#include <linux/types.h>
+#include <linux/string.h>
+#include <asm/byteorder.h>
+
+#define fdt16_to_cpu(x)		be16_to_cpu(x)
+#define cpu_to_fdt16(x)		cpu_to_be16(x)
+#define fdt32_to_cpu(x)		be32_to_cpu(x)
+#define cpu_to_fdt32(x)		cpu_to_be32(x)
+#define fdt64_to_cpu(x)		be64_to_cpu(x)
+#define cpu_to_fdt64(x)		cpu_to_be64(x)
+
+#endif
diff --git a/arch/arm/boot/compressed/misc.c b/arch/arm/boot/compressed/misc.c
index 832d372..8e2a8fc 100644
--- a/arch/arm/boot/compressed/misc.c
+++ b/arch/arm/boot/compressed/misc.c
@@ -18,14 +18,9 @@
 
 unsigned int __machine_arch_type;
 
-#define _LINUX_STRING_H_
-
 #include <linux/compiler.h>	/* for inline */
-#include <linux/types.h>	/* for size_t */
-#include <linux/stddef.h>	/* for NULL */
+#include <linux/types.h>
 #include <linux/linkage.h>
-#include <asm/string.h>
-
 
 static void putstr(const char *ptr);
 extern void error(char *x);
@@ -101,41 +96,6 @@
 	flush();
 }
 
-
-void *memcpy(void *__dest, __const void *__src, size_t __n)
-{
-	int i = 0;
-	unsigned char *d = (unsigned char *)__dest, *s = (unsigned char *)__src;
-
-	for (i = __n >> 3; i > 0; i--) {
-		*d++ = *s++;
-		*d++ = *s++;
-		*d++ = *s++;
-		*d++ = *s++;
-		*d++ = *s++;
-		*d++ = *s++;
-		*d++ = *s++;
-		*d++ = *s++;
-	}
-
-	if (__n & 1 << 2) {
-		*d++ = *s++;
-		*d++ = *s++;
-		*d++ = *s++;
-		*d++ = *s++;
-	}
-
-	if (__n & 1 << 1) {
-		*d++ = *s++;
-		*d++ = *s++;
-	}
-
-	if (__n & 1)
-		*d++ = *s++;
-
-	return __dest;
-}
-
 /*
  * gzip declarations
  */
diff --git a/arch/arm/boot/compressed/string.c b/arch/arm/boot/compressed/string.c
new file mode 100644
index 0000000..36e53ef
--- /dev/null
+++ b/arch/arm/boot/compressed/string.c
@@ -0,0 +1,127 @@
+/*
+ * arch/arm/boot/compressed/string.c
+ *
+ * Small subset of simple string routines
+ */
+
+#include <linux/string.h>
+
+void *memcpy(void *__dest, __const void *__src, size_t __n)
+{
+	int i = 0;
+	unsigned char *d = (unsigned char *)__dest, *s = (unsigned char *)__src;
+
+	for (i = __n >> 3; i > 0; i--) {
+		*d++ = *s++;
+		*d++ = *s++;
+		*d++ = *s++;
+		*d++ = *s++;
+		*d++ = *s++;
+		*d++ = *s++;
+		*d++ = *s++;
+		*d++ = *s++;
+	}
+
+	if (__n & 1 << 2) {
+		*d++ = *s++;
+		*d++ = *s++;
+		*d++ = *s++;
+		*d++ = *s++;
+	}
+
+	if (__n & 1 << 1) {
+		*d++ = *s++;
+		*d++ = *s++;
+	}
+
+	if (__n & 1)
+		*d++ = *s++;
+
+	return __dest;
+}
+
+void *memmove(void *__dest, __const void *__src, size_t count)
+{
+	unsigned char *d = __dest;
+	const unsigned char *s = __src;
+
+	if (__dest == __src)
+		return __dest;
+
+	if (__dest < __src)
+		return memcpy(__dest, __src, count);
+
+	while (count--)
+		d[count] = s[count];
+	return __dest;
+}
+
+size_t strlen(const char *s)
+{
+	const char *sc = s;
+
+	while (*sc != '\0')
+		sc++;
+	return sc - s;
+}
+
+int memcmp(const void *cs, const void *ct, size_t count)
+{
+	const unsigned char *su1 = cs, *su2 = ct, *end = su1 + count;
+	int res = 0;
+
+	while (su1 < end) {
+		res = *su1++ - *su2++;
+		if (res)
+			break;
+	}
+	return res;
+}
+
+int strcmp(const char *cs, const char *ct)
+{
+	unsigned char c1, c2;
+	int res = 0;
+
+	do {
+		c1 = *cs++;
+		c2 = *ct++;
+		res = c1 - c2;
+		if (res)
+			break;
+	} while (c1);
+	return res;
+}
+
+void *memchr(const void *s, int c, size_t count)
+{
+	const unsigned char *p = s;
+
+	while (count--)
+		if ((unsigned char)c == *p++)
+			return (void *)(p - 1);
+	return NULL;
+}
+
+char *strchr(const char *s, int c)
+{
+	while (*s != (char)c)
+		if (*s++ == '\0')
+			return NULL;
+	return (char *)s;
+}
+
+#undef memset
+
+void *memset(void *s, int c, size_t count)
+{
+	char *xs = s;
+	while (count--)
+		*xs++ = c;
+	return s;
+}
+
+void __memzero(void *s, size_t count)
+{
+	memset(s, 0, count);
+}
diff --git a/arch/arm/boot/compressed/vmlinux.lds.in b/arch/arm/boot/compressed/vmlinux.lds.in
index 4e72883..4919f2a 100644
--- a/arch/arm/boot/compressed/vmlinux.lds.in
+++ b/arch/arm/boot/compressed/vmlinux.lds.in
@@ -51,6 +51,10 @@
   _got_start = .;
   .got			: { *(.got) }
   _got_end = .;
+
+  /* ensure the zImage file size is always a multiple of 64 bits */
+  /* (without a dummy byte, ld just ignores the empty section) */
+  .pad			: { BYTE(0); . = ALIGN(8); }
   _edata = .;
 
   . = BSS_START;
diff --git a/arch/arm/common/Kconfig b/arch/arm/common/Kconfig
index 4b71766..74df9ca 100644
--- a/arch/arm/common/Kconfig
+++ b/arch/arm/common/Kconfig
@@ -1,4 +1,5 @@
 config ARM_GIC
+	select IRQ_DOMAIN
 	bool
 
 config ARM_VIC
diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c
index 3227ca9..9d77777 100644
--- a/arch/arm/common/gic.c
+++ b/arch/arm/common/gic.c
@@ -24,10 +24,20 @@
  */
 #include <linux/init.h>
 #include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/export.h>
 #include <linux/list.h>
 #include <linux/smp.h>
+#include <linux/cpu_pm.h>
 #include <linux/cpumask.h>
 #include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/irqdomain.h>
+#include <linux/interrupt.h>
+#include <linux/percpu.h>
+#include <linux/slab.h>
 
 #include <asm/irq.h>
 #include <asm/mach/irq.h>
@@ -71,8 +81,7 @@
 
 static inline unsigned int gic_irq(struct irq_data *d)
 {
-	struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d);
-	return d->irq - gic_data->irq_offset;
+	return d->hwirq;
 }
 
 /*
@@ -80,7 +89,7 @@
  */
 static void gic_mask_irq(struct irq_data *d)
 {
-	u32 mask = 1 << (d->irq % 32);
+	u32 mask = 1 << (gic_irq(d) % 32);
 
 	spin_lock(&irq_controller_lock);
 	writel_relaxed(mask, gic_dist_base(d) + GIC_DIST_ENABLE_CLEAR + (gic_irq(d) / 32) * 4);
@@ -91,7 +100,7 @@
 
 static void gic_unmask_irq(struct irq_data *d)
 {
-	u32 mask = 1 << (d->irq % 32);
+	u32 mask = 1 << (gic_irq(d) % 32);
 
 	spin_lock(&irq_controller_lock);
 	if (gic_arch_extn.irq_unmask)
@@ -172,7 +181,7 @@
 			    bool force)
 {
 	void __iomem *reg = gic_dist_base(d) + GIC_DIST_TARGET + (gic_irq(d) & ~3);
-	unsigned int shift = (d->irq % 4) * 8;
+	unsigned int shift = (gic_irq(d) % 4) * 8;
 	unsigned int cpu = cpumask_any_and(mask_val, cpu_online_mask);
 	u32 val, mask, bit;
 
@@ -180,7 +189,7 @@
 		return -EINVAL;
 
 	mask = 0xff << shift;
-	bit = 1 << (cpu + shift);
+	bit = 1 << (cpu_logical_map(cpu) + shift);
 
 	spin_lock(&irq_controller_lock);
 	val = readl_relaxed(reg) & ~mask;
@@ -223,7 +232,7 @@
 	if (gic_irq == 1023)
 		goto out;
 
-	cascade_irq = gic_irq + chip_data->irq_offset;
+	cascade_irq = irq_domain_to_irq(&chip_data->domain, gic_irq);
 	if (unlikely(gic_irq < 32 || gic_irq > 1020 || cascade_irq >= NR_IRQS))
 		do_bad_IRQ(cascade_irq, desc);
 	else
@@ -255,28 +264,26 @@
 	irq_set_chained_handler(irq, gic_handle_cascade_irq);
 }
 
-static void __init gic_dist_init(struct gic_chip_data *gic,
-	unsigned int irq_start)
+static void __init gic_dist_init(struct gic_chip_data *gic)
 {
-	unsigned int gic_irqs, irq_limit, i;
+	unsigned int i, irq;
+	u32 cpumask;
+	unsigned int gic_irqs = gic->gic_irqs;
+	struct irq_domain *domain = &gic->domain;
 	void __iomem *base = gic->dist_base;
-	u32 cpumask = 1 << smp_processor_id();
+	u32 cpu = 0;
 
+#ifdef CONFIG_SMP
+	cpu = cpu_logical_map(smp_processor_id());
+#endif
+
+	cpumask = 1 << cpu;
 	cpumask |= cpumask << 8;
 	cpumask |= cpumask << 16;
 
 	writel_relaxed(0, base + GIC_DIST_CTRL);
 
 	/*
-	 * Find out how many interrupts are supported.
-	 * The GIC only supports up to 1020 interrupt sources.
-	 */
-	gic_irqs = readl_relaxed(base + GIC_DIST_CTR) & 0x1f;
-	gic_irqs = (gic_irqs + 1) * 32;
-	if (gic_irqs > 1020)
-		gic_irqs = 1020;
-
-	/*
 	 * Set all global interrupts to be level triggered, active low.
 	 */
 	for (i = 32; i < gic_irqs; i += 16)
@@ -302,19 +309,20 @@
 		writel_relaxed(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32);
 
 	/*
-	 * Limit number of interrupts registered to the platform maximum
-	 */
-	irq_limit = gic->irq_offset + gic_irqs;
-	if (WARN_ON(irq_limit > NR_IRQS))
-		irq_limit = NR_IRQS;
-
-	/*
 	 * Setup the Linux IRQ subsystem.
 	 */
-	for (i = irq_start; i < irq_limit; i++) {
-		irq_set_chip_and_handler(i, &gic_chip, handle_fasteoi_irq);
-		irq_set_chip_data(i, gic);
-		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
+	irq_domain_for_each_irq(domain, i, irq) {
+		if (i < 32) {
+			irq_set_percpu_devid(irq);
+			irq_set_chip_and_handler(irq, &gic_chip,
+						 handle_percpu_devid_irq);
+			set_irq_flags(irq, IRQF_VALID | IRQF_NOAUTOEN);
+		} else {
+			irq_set_chip_and_handler(irq, &gic_chip,
+						 handle_fasteoi_irq);
+			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		}
+		irq_set_chip_data(irq, gic);
 	}
 
 	writel_relaxed(1, base + GIC_DIST_CTRL);
@@ -343,23 +351,270 @@
 	writel_relaxed(1, base + GIC_CPU_CTRL);
 }
 
-void __init gic_init(unsigned int gic_nr, unsigned int irq_start,
+#ifdef CONFIG_CPU_PM
+/*
+ * Saves the GIC distributor registers during suspend or idle.  Must be called
+ * with interrupts disabled but before powering down the GIC.  After calling
+ * this function, no interrupts will be delivered by the GIC, and another
+ * platform-specific wakeup source must be enabled.
+ */
+static void gic_dist_save(unsigned int gic_nr)
+{
+	unsigned int gic_irqs;
+	void __iomem *dist_base;
+	int i;
+
+	if (gic_nr >= MAX_GIC_NR)
+		BUG();
+
+	gic_irqs = gic_data[gic_nr].gic_irqs;
+	dist_base = gic_data[gic_nr].dist_base;
+
+	if (!dist_base)
+		return;
+
+	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 16); i++)
+		gic_data[gic_nr].saved_spi_conf[i] =
+			readl_relaxed(dist_base + GIC_DIST_CONFIG + i * 4);
+
+	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
+		gic_data[gic_nr].saved_spi_target[i] =
+			readl_relaxed(dist_base + GIC_DIST_TARGET + i * 4);
+
+	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++)
+		gic_data[gic_nr].saved_spi_enable[i] =
+			readl_relaxed(dist_base + GIC_DIST_ENABLE_SET + i * 4);
+}
+
+/*
+ * Restores the GIC distributor registers during resume or when coming out of
+ * idle.  Must be called before enabling interrupts.  If a level interrupt
+ * that occured while the GIC was suspended is still present, it will be
+ * handled normally, but any edge interrupts that occured will not be seen by
+ * the GIC and need to be handled by the platform-specific wakeup source.
+ */
+static void gic_dist_restore(unsigned int gic_nr)
+{
+	unsigned int gic_irqs;
+	unsigned int i;
+	void __iomem *dist_base;
+
+	if (gic_nr >= MAX_GIC_NR)
+		BUG();
+
+	gic_irqs = gic_data[gic_nr].gic_irqs;
+	dist_base = gic_data[gic_nr].dist_base;
+
+	if (!dist_base)
+		return;
+
+	writel_relaxed(0, dist_base + GIC_DIST_CTRL);
+
+	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 16); i++)
+		writel_relaxed(gic_data[gic_nr].saved_spi_conf[i],
+			dist_base + GIC_DIST_CONFIG + i * 4);
+
+	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
+		writel_relaxed(0xa0a0a0a0,
+			dist_base + GIC_DIST_PRI + i * 4);
+
+	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
+		writel_relaxed(gic_data[gic_nr].saved_spi_target[i],
+			dist_base + GIC_DIST_TARGET + i * 4);
+
+	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++)
+		writel_relaxed(gic_data[gic_nr].saved_spi_enable[i],
+			dist_base + GIC_DIST_ENABLE_SET + i * 4);
+
+	writel_relaxed(1, dist_base + GIC_DIST_CTRL);
+}
+
+static void gic_cpu_save(unsigned int gic_nr)
+{
+	int i;
+	u32 *ptr;
+	void __iomem *dist_base;
+	void __iomem *cpu_base;
+
+	if (gic_nr >= MAX_GIC_NR)
+		BUG();
+
+	dist_base = gic_data[gic_nr].dist_base;
+	cpu_base = gic_data[gic_nr].cpu_base;
+
+	if (!dist_base || !cpu_base)
+		return;
+
+	ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_enable);
+	for (i = 0; i < DIV_ROUND_UP(32, 32); i++)
+		ptr[i] = readl_relaxed(dist_base + GIC_DIST_ENABLE_SET + i * 4);
+
+	ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_conf);
+	for (i = 0; i < DIV_ROUND_UP(32, 16); i++)
+		ptr[i] = readl_relaxed(dist_base + GIC_DIST_CONFIG + i * 4);
+
+}
+
+static void gic_cpu_restore(unsigned int gic_nr)
+{
+	int i;
+	u32 *ptr;
+	void __iomem *dist_base;
+	void __iomem *cpu_base;
+
+	if (gic_nr >= MAX_GIC_NR)
+		BUG();
+
+	dist_base = gic_data[gic_nr].dist_base;
+	cpu_base = gic_data[gic_nr].cpu_base;
+
+	if (!dist_base || !cpu_base)
+		return;
+
+	ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_enable);
+	for (i = 0; i < DIV_ROUND_UP(32, 32); i++)
+		writel_relaxed(ptr[i], dist_base + GIC_DIST_ENABLE_SET + i * 4);
+
+	ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_conf);
+	for (i = 0; i < DIV_ROUND_UP(32, 16); i++)
+		writel_relaxed(ptr[i], dist_base + GIC_DIST_CONFIG + i * 4);
+
+	for (i = 0; i < DIV_ROUND_UP(32, 4); i++)
+		writel_relaxed(0xa0a0a0a0, dist_base + GIC_DIST_PRI + i * 4);
+
+	writel_relaxed(0xf0, cpu_base + GIC_CPU_PRIMASK);
+	writel_relaxed(1, cpu_base + GIC_CPU_CTRL);
+}
+
+static int gic_notifier(struct notifier_block *self, unsigned long cmd,	void *v)
+{
+	int i;
+
+	for (i = 0; i < MAX_GIC_NR; i++) {
+		switch (cmd) {
+		case CPU_PM_ENTER:
+			gic_cpu_save(i);
+			break;
+		case CPU_PM_ENTER_FAILED:
+		case CPU_PM_EXIT:
+			gic_cpu_restore(i);
+			break;
+		case CPU_CLUSTER_PM_ENTER:
+			gic_dist_save(i);
+			break;
+		case CPU_CLUSTER_PM_ENTER_FAILED:
+		case CPU_CLUSTER_PM_EXIT:
+			gic_dist_restore(i);
+			break;
+		}
+	}
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block gic_notifier_block = {
+	.notifier_call = gic_notifier,
+};
+
+static void __init gic_pm_init(struct gic_chip_data *gic)
+{
+	gic->saved_ppi_enable = __alloc_percpu(DIV_ROUND_UP(32, 32) * 4,
+		sizeof(u32));
+	BUG_ON(!gic->saved_ppi_enable);
+
+	gic->saved_ppi_conf = __alloc_percpu(DIV_ROUND_UP(32, 16) * 4,
+		sizeof(u32));
+	BUG_ON(!gic->saved_ppi_conf);
+
+	cpu_pm_register_notifier(&gic_notifier_block);
+}
+#else
+static void __init gic_pm_init(struct gic_chip_data *gic)
+{
+}
+#endif
+
+#ifdef CONFIG_OF
+static int gic_irq_domain_dt_translate(struct irq_domain *d,
+				       struct device_node *controller,
+				       const u32 *intspec, unsigned int intsize,
+				       unsigned long *out_hwirq, unsigned int *out_type)
+{
+	if (d->of_node != controller)
+		return -EINVAL;
+	if (intsize < 3)
+		return -EINVAL;
+
+	/* Get the interrupt number and add 16 to skip over SGIs */
+	*out_hwirq = intspec[1] + 16;
+
+	/* For SPIs, we need to add 16 more to get the GIC irq ID number */
+	if (!intspec[0])
+		*out_hwirq += 16;
+
+	*out_type = intspec[2] & IRQ_TYPE_SENSE_MASK;
+	return 0;
+}
+#endif
+
+const struct irq_domain_ops gic_irq_domain_ops = {
+#ifdef CONFIG_OF
+	.dt_translate = gic_irq_domain_dt_translate,
+#endif
+};
+
+void __init gic_init(unsigned int gic_nr, int irq_start,
 	void __iomem *dist_base, void __iomem *cpu_base)
 {
 	struct gic_chip_data *gic;
+	struct irq_domain *domain;
+	int gic_irqs;
 
 	BUG_ON(gic_nr >= MAX_GIC_NR);
 
 	gic = &gic_data[gic_nr];
+	domain = &gic->domain;
 	gic->dist_base = dist_base;
 	gic->cpu_base = cpu_base;
-	gic->irq_offset = (irq_start - 1) & ~31;
 
-	if (gic_nr == 0)
+	/*
+	 * For primary GICs, skip over SGIs.
+	 * For secondary GICs, skip over PPIs, too.
+	 */
+	if (gic_nr == 0) {
 		gic_cpu_base_addr = cpu_base;
+		domain->hwirq_base = 16;
+		if (irq_start > 0)
+			irq_start = (irq_start & ~31) + 16;
+	} else
+		domain->hwirq_base = 32;
 
-	gic_dist_init(gic, irq_start);
+	/*
+	 * Find out how many interrupts are supported.
+	 * The GIC only supports up to 1020 interrupt sources.
+	 */
+	gic_irqs = readl_relaxed(dist_base + GIC_DIST_CTR) & 0x1f;
+	gic_irqs = (gic_irqs + 1) * 32;
+	if (gic_irqs > 1020)
+		gic_irqs = 1020;
+	gic->gic_irqs = gic_irqs;
+
+	domain->nr_irq = gic_irqs - domain->hwirq_base;
+	domain->irq_base = irq_alloc_descs(irq_start, 16, domain->nr_irq,
+					   numa_node_id());
+	if (IS_ERR_VALUE(domain->irq_base)) {
+		WARN(1, "Cannot allocate irq_descs @ IRQ%d, assuming pre-allocated\n",
+		     irq_start);
+		domain->irq_base = irq_start;
+	}
+	domain->priv = gic;
+	domain->ops = &gic_irq_domain_ops;
+	irq_domain_add(domain);
+
+	gic_chip.flags |= gic_arch_extn.flags;
+	gic_dist_init(gic);
 	gic_cpu_init(gic);
+	gic_pm_init(gic);
 }
 
 void __cpuinit gic_secondary_init(unsigned int gic_nr)
@@ -369,20 +624,15 @@
 	gic_cpu_init(&gic_data[gic_nr]);
 }
 
-void __cpuinit gic_enable_ppi(unsigned int irq)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-	irq_set_status_flags(irq, IRQ_NOPROBE);
-	gic_unmask_irq(irq_get_irq_data(irq));
-	local_irq_restore(flags);
-}
-
 #ifdef CONFIG_SMP
 void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
 {
-	unsigned long map = *cpus_addr(*mask);
+	int cpu;
+	unsigned long map = 0;
+
+	/* Convert our logical CPU mask into a physical one. */
+	for_each_cpu(cpu, mask)
+		map |= 1 << cpu_logical_map(cpu);
 
 	/*
 	 * Ensure that stores to Normal memory are visible to the
@@ -394,3 +644,35 @@
 	writel_relaxed(map << 16 | irq, gic_data[0].dist_base + GIC_DIST_SOFTINT);
 }
 #endif
+
+#ifdef CONFIG_OF
+static int gic_cnt __initdata = 0;
+
+int __init gic_of_init(struct device_node *node, struct device_node *parent)
+{
+	void __iomem *cpu_base;
+	void __iomem *dist_base;
+	int irq;
+	struct irq_domain *domain = &gic_data[gic_cnt].domain;
+
+	if (WARN_ON(!node))
+		return -ENODEV;
+
+	dist_base = of_iomap(node, 0);
+	WARN(!dist_base, "unable to map gic dist registers\n");
+
+	cpu_base = of_iomap(node, 1);
+	WARN(!cpu_base, "unable to map gic cpu registers\n");
+
+	domain->of_node = of_node_get(node);
+
+	gic_init(gic_cnt, -1, dist_base, cpu_base);
+
+	if (parent) {
+		irq = irq_of_parse_and_map(node, 0);
+		gic_cascade_irq(gic_cnt, irq);
+	}
+	gic_cnt++;
+	return 0;
+}
+#endif
diff --git a/arch/arm/include/asm/cputype.h b/arch/arm/include/asm/cputype.h
index cd4458f..cb47d28 100644
--- a/arch/arm/include/asm/cputype.h
+++ b/arch/arm/include/asm/cputype.h
@@ -8,6 +8,7 @@
 #define CPUID_CACHETYPE	1
 #define CPUID_TCM	2
 #define CPUID_TLBTYPE	3
+#define CPUID_MPIDR	5
 
 #define CPUID_EXT_PFR0	"c1, 0"
 #define CPUID_EXT_PFR1	"c1, 1"
@@ -70,6 +71,11 @@
 	return read_cpuid(CPUID_TCM);
 }
 
+static inline unsigned int __attribute_const__ read_cpuid_mpidr(void)
+{
+	return read_cpuid(CPUID_MPIDR);
+}
+
 /*
  * Intel's XScale3 core supports some v6 features (supersections, L2)
  * but advertises itself as v5 as it does not support the v6 ISA.  For
diff --git a/arch/arm/include/asm/dma-mapping.h b/arch/arm/include/asm/dma-mapping.h
index 7a21d0b..7f27fab 100644
--- a/arch/arm/include/asm/dma-mapping.h
+++ b/arch/arm/include/asm/dma-mapping.h
@@ -205,6 +205,13 @@
 int dma_mmap_writecombine(struct device *, struct vm_area_struct *,
 		void *, dma_addr_t, size_t);
 
+/*
+ * This can be called during boot to increase the size of the consistent
+ * DMA region above it's default value of 2MB. It must be called before the
+ * memory allocator is initialised, i.e. before any core_initcall.
+ */
+extern void __init init_consistent_dma_size(unsigned long size);
+
 
 #ifdef CONFIG_DMABOUNCE
 /*
diff --git a/arch/arm/include/asm/entry-macro-multi.S b/arch/arm/include/asm/entry-macro-multi.S
index 2f1e209..88d6181 100644
--- a/arch/arm/include/asm/entry-macro-multi.S
+++ b/arch/arm/include/asm/entry-macro-multi.S
@@ -25,13 +25,6 @@
 	movne	r1, sp
 	adrne	lr, BSYM(1b)
 	bne	do_IPI
-
-#ifdef CONFIG_LOCAL_TIMERS
-	test_for_ltirq r0, r2, r6, lr
-	movne	r0, sp
-	adrne	lr, BSYM(1b)
-	bne	do_local_timer
-#endif
 #endif
 9997:
 	.endm
diff --git a/arch/arm/include/asm/exception.h b/arch/arm/include/asm/exception.h
new file mode 100644
index 0000000..5abaf5b
--- /dev/null
+++ b/arch/arm/include/asm/exception.h
@@ -0,0 +1,19 @@
+/*
+ * Annotations for marking C functions as exception handlers.
+ *
+ * These should only be used for C functions that are called from the low
+ * level exception entry code and not any intervening C code.
+ */
+#ifndef __ASM_ARM_EXCEPTION_H
+#define __ASM_ARM_EXCEPTION_H
+
+#include <linux/ftrace.h>
+
+#define __exception	__attribute__((section(".exception.text")))
+#ifdef CONFIG_FUNCTION_GRAPH_TRACER
+#define __exception_irq_entry	__irq_entry
+#else
+#define __exception_irq_entry	__exception
+#endif
+
+#endif /* __ASM_ARM_EXCEPTION_H */
diff --git a/arch/arm/include/asm/hardirq.h b/arch/arm/include/asm/hardirq.h
index 89ad180..ddf07a9 100644
--- a/arch/arm/include/asm/hardirq.h
+++ b/arch/arm/include/asm/hardirq.h
@@ -9,9 +9,6 @@
 
 typedef struct {
 	unsigned int __softirq_pending;
-#ifdef CONFIG_LOCAL_TIMERS
-	unsigned int local_timer_irqs;
-#endif
 #ifdef CONFIG_SMP
 	unsigned int ipi_irqs[NR_IPI];
 #endif
diff --git a/arch/arm/include/asm/hardware/entry-macro-gic.S b/arch/arm/include/asm/hardware/entry-macro-gic.S
index c115b82..74ebc80 100644
--- a/arch/arm/include/asm/hardware/entry-macro-gic.S
+++ b/arch/arm/include/asm/hardware/entry-macro-gic.S
@@ -22,15 +22,11 @@
  * interrupt controller spec.  To wit:
  *
  * Interrupts 0-15 are IPI
- * 16-28 are reserved
- * 29-31 are local.  We allow 30 to be used for the watchdog.
+ * 16-31 are local.  We allow 30 to be used for the watchdog.
  * 32-1020 are global
  * 1021-1022 are reserved
  * 1023 is "spurious" (no interrupt)
  *
- * For now, we ignore all local interrupts so only return an interrupt if it's
- * between 30 and 1020.  The test_for_ipi routine below will pick up on IPIs.
- *
  * A simple read from the controller will tell us the number of the highest
  * priority enabled interrupt.  We then just need to check whether it is in the
  * valid range for an IRQ (30-1020 inclusive).
@@ -43,7 +39,7 @@
 
 	ldr	\tmp, =1021
 	bic     \irqnr, \irqstat, #0x1c00
-	cmp     \irqnr, #29
+	cmp     \irqnr, #15
 	cmpcc	\irqnr, \irqnr
 	cmpne	\irqnr, \tmp
 	cmpcs	\irqnr, \irqnr
@@ -62,14 +58,3 @@
 	strcc	\irqstat, [\base, #GIC_CPU_EOI]
 	cmpcs	\irqnr, \irqnr
 	.endm
-
-/* As above, this assumes that irqstat and base are preserved.. */
-
-	.macro test_for_ltirq, irqnr, irqstat, base, tmp
-	bic	\irqnr, \irqstat, #0x1c00
-	mov 	\tmp, #0
-	cmp	\irqnr, #29
-	moveq	\tmp, #1
-	streq	\irqstat, [\base, #GIC_CPU_EOI]
-	cmp	\tmp, #0
-	.endm
diff --git a/arch/arm/include/asm/hardware/gic.h b/arch/arm/include/asm/hardware/gic.h
index 435d3f8..3e91f22 100644
--- a/arch/arm/include/asm/hardware/gic.h
+++ b/arch/arm/include/asm/hardware/gic.h
@@ -33,19 +33,32 @@
 #define GIC_DIST_SOFTINT		0xf00
 
 #ifndef __ASSEMBLY__
+#include <linux/irqdomain.h>
+struct device_node;
+
 extern void __iomem *gic_cpu_base_addr;
 extern struct irq_chip gic_arch_extn;
 
-void gic_init(unsigned int, unsigned int, void __iomem *, void __iomem *);
+void gic_init(unsigned int, int, void __iomem *, void __iomem *);
+int gic_of_init(struct device_node *node, struct device_node *parent);
 void gic_secondary_init(unsigned int);
 void gic_cascade_irq(unsigned int gic_nr, unsigned int irq);
 void gic_raise_softirq(const struct cpumask *mask, unsigned int irq);
-void gic_enable_ppi(unsigned int);
 
 struct gic_chip_data {
-	unsigned int irq_offset;
 	void __iomem *dist_base;
 	void __iomem *cpu_base;
+#ifdef CONFIG_CPU_PM
+	u32 saved_spi_enable[DIV_ROUND_UP(1020, 32)];
+	u32 saved_spi_conf[DIV_ROUND_UP(1020, 16)];
+	u32 saved_spi_target[DIV_ROUND_UP(1020, 4)];
+	u32 __percpu *saved_ppi_enable;
+	u32 __percpu *saved_ppi_conf;
+#endif
+#ifdef CONFIG_IRQ_DOMAIN
+	struct irq_domain domain;
+#endif
+	unsigned int gic_irqs;
 };
 #endif
 
diff --git a/arch/arm/include/asm/hw_breakpoint.h b/arch/arm/include/asm/hw_breakpoint.h
index f389b27..c190bc9 100644
--- a/arch/arm/include/asm/hw_breakpoint.h
+++ b/arch/arm/include/asm/hw_breakpoint.h
@@ -50,6 +50,7 @@
 #define ARM_DEBUG_ARCH_V6_1	2
 #define ARM_DEBUG_ARCH_V7_ECP14	3
 #define ARM_DEBUG_ARCH_V7_MM	4
+#define ARM_DEBUG_ARCH_V7_1	5
 
 /* Breakpoint */
 #define ARM_BREAKPOINT_EXECUTE	0
@@ -57,6 +58,7 @@
 /* Watchpoints */
 #define ARM_BREAKPOINT_LOAD	1
 #define ARM_BREAKPOINT_STORE	2
+#define ARM_FSR_ACCESS_MASK	(1 << 11)
 
 /* Privilege Levels */
 #define ARM_BREAKPOINT_PRIV	1
diff --git a/arch/arm/include/asm/localtimer.h b/arch/arm/include/asm/localtimer.h
index 080d74f..f5e1cec 100644
--- a/arch/arm/include/asm/localtimer.h
+++ b/arch/arm/include/asm/localtimer.h
@@ -10,6 +10,8 @@
 #ifndef __ASM_ARM_LOCALTIMER_H
 #define __ASM_ARM_LOCALTIMER_H
 
+#include <linux/interrupt.h>
+
 struct clock_event_device;
 
 /*
@@ -17,27 +19,20 @@
  */
 void percpu_timer_setup(void);
 
-/*
- * Called from assembly, this is the local timer IRQ handler
- */
-asmlinkage void do_local_timer(struct pt_regs *);
-
-
 #ifdef CONFIG_LOCAL_TIMERS
 
 #ifdef CONFIG_HAVE_ARM_TWD
 
 #include "smp_twd.h"
 
-#define local_timer_ack()	twd_timer_ack()
+#define local_timer_stop(c)	twd_timer_stop((c))
 
 #else
 
 /*
- * Platform provides this to acknowledge a local timer IRQ.
- * Returns true if the local timer IRQ is to be processed.
+ * Stop the local timer
  */
-int local_timer_ack(void);
+void local_timer_stop(struct clock_event_device *);
 
 #endif
 
@@ -52,6 +47,10 @@
 {
 	return -ENXIO;
 }
+
+static inline void local_timer_stop(struct clock_event_device *evt)
+{
+}
 #endif
 
 #endif
diff --git a/arch/arm/include/asm/mach/arch.h b/arch/arm/include/asm/mach/arch.h
index 217aa191..727da11 100644
--- a/arch/arm/include/asm/mach/arch.h
+++ b/arch/arm/include/asm/mach/arch.h
@@ -17,7 +17,7 @@
 struct machine_desc {
 	unsigned int		nr;		/* architecture number	*/
 	const char		*name;		/* architecture name	*/
-	unsigned long		boot_params;	/* tagged list		*/
+	unsigned long		atag_offset;	/* tagged list (relative) */
 	const char		**dt_compat;	/* array of device tree
 						 * 'compatible' strings	*/
 
diff --git a/arch/arm/include/asm/mach/map.h b/arch/arm/include/asm/mach/map.h
index d2fedb5..b36f365 100644
--- a/arch/arm/include/asm/mach/map.h
+++ b/arch/arm/include/asm/mach/map.h
@@ -29,6 +29,7 @@
 #define MT_MEMORY_NONCACHED	11
 #define MT_MEMORY_DTCM		12
 #define MT_MEMORY_ITCM		13
+#define MT_MEMORY_SO		14
 
 #ifdef CONFIG_MMU
 extern void iotable_init(struct map_desc *, int);
diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h
index b8de516..a8997d7 100644
--- a/arch/arm/include/asm/memory.h
+++ b/arch/arm/include/asm/memory.h
@@ -16,9 +16,12 @@
 #include <linux/compiler.h>
 #include <linux/const.h>
 #include <linux/types.h>
-#include <mach/memory.h>
 #include <asm/sizes.h>
 
+#ifdef CONFIG_NEED_MACH_MEMORY_H
+#include <mach/memory.h>
+#endif
+
 /*
  * Allow for constants defined here to be used from assembly code
  * by prepending the UL suffix only with actual C code compilation.
@@ -77,16 +80,7 @@
  */
 #define IOREMAP_MAX_ORDER	24
 
-/*
- * Size of DMA-consistent memory region.  Must be multiple of 2M,
- * between 2MB and 14MB inclusive.
- */
-#ifndef CONSISTENT_DMA_SIZE
-#define CONSISTENT_DMA_SIZE 	SZ_2M
-#endif
-
 #define CONSISTENT_END		(0xffe00000UL)
-#define CONSISTENT_BASE		(CONSISTENT_END - CONSISTENT_DMA_SIZE)
 
 #else /* CONFIG_MMU */
 
@@ -160,7 +154,6 @@
  * so that all we need to do is modify the 8-bit constant field.
  */
 #define __PV_BITS_31_24	0x81000000
-#define __PV_BITS_23_16	0x00810000
 
 extern unsigned long __pv_phys_offset;
 #define PHYS_OFFSET __pv_phys_offset
@@ -178,9 +171,6 @@
 {
 	unsigned long t;
 	__pv_stub(x, t, "add", __PV_BITS_31_24);
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-	__pv_stub(t, t, "add", __PV_BITS_23_16);
-#endif
 	return t;
 }
 
@@ -188,9 +178,6 @@
 {
 	unsigned long t;
 	__pv_stub(x, t, "sub", __PV_BITS_31_24);
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-	__pv_stub(t, t, "sub", __PV_BITS_23_16);
-#endif
 	return t;
 }
 #else
@@ -200,7 +187,11 @@
 #endif
 
 #ifndef PHYS_OFFSET
+#ifdef PLAT_PHYS_OFFSET
 #define PHYS_OFFSET	PLAT_PHYS_OFFSET
+#else
+#define PHYS_OFFSET	UL(CONFIG_PHYS_OFFSET)
+#endif
 #endif
 
 /*
diff --git a/arch/arm/include/asm/module.h b/arch/arm/include/asm/module.h
index 543b449..6c6809f 100644
--- a/arch/arm/include/asm/module.h
+++ b/arch/arm/include/asm/module.h
@@ -31,11 +31,7 @@
 
 /* Add __virt_to_phys patching state as well */
 #ifdef CONFIG_ARM_PATCH_PHYS_VIRT
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-#define MODULE_ARCH_VERMAGIC_P2V "p2v16 "
-#else
 #define MODULE_ARCH_VERMAGIC_P2V "p2v8 "
-#endif
 #else
 #define MODULE_ARCH_VERMAGIC_P2V ""
 #endif
diff --git a/arch/arm/include/asm/pgtable.h b/arch/arm/include/asm/pgtable.h
index 5750704..f1956b2 100644
--- a/arch/arm/include/asm/pgtable.h
+++ b/arch/arm/include/asm/pgtable.h
@@ -232,6 +232,9 @@
 #define pgprot_writecombine(prot) \
 	__pgprot_modify(prot, L_PTE_MT_MASK, L_PTE_MT_BUFFERABLE)
 
+#define pgprot_stronglyordered(prot) \
+	__pgprot_modify(prot, L_PTE_MT_MASK, L_PTE_MT_UNCACHED)
+
 #ifdef CONFIG_ARM_DMA_MEM_BUFFERABLE
 #define pgprot_dmacoherent(prot) \
 	__pgprot_modify(prot, L_PTE_MT_MASK, L_PTE_MT_BUFFERABLE | L_PTE_XN)
diff --git a/arch/arm/include/asm/pmu.h b/arch/arm/include/asm/pmu.h
index b7e82c4..71d99b8 100644
--- a/arch/arm/include/asm/pmu.h
+++ b/arch/arm/include/asm/pmu.h
@@ -13,7 +13,12 @@
 #define __ARM_PMU_H__
 
 #include <linux/interrupt.h>
+#include <linux/perf_event.h>
 
+/*
+ * Types of PMUs that can be accessed directly and require mutual
+ * exclusion between profiling tools.
+ */
 enum arm_pmu_type {
 	ARM_PMU_DEVICE_CPU	= 0,
 	ARM_NUM_PMU_DEVICES,
@@ -37,21 +42,17 @@
  * reserve_pmu() - reserve the hardware performance counters
  *
  * Reserve the hardware performance counters in the system for exclusive use.
- * The platform_device for the system is returned on success, ERR_PTR()
- * encoded error on failure.
+ * Returns 0 on success or -EBUSY if the lock is already held.
  */
-extern struct platform_device *
+extern int
 reserve_pmu(enum arm_pmu_type type);
 
 /**
  * release_pmu() - Relinquish control of the performance counters
  *
  * Release the performance counters and allow someone else to use them.
- * Callers must have disabled the counters and released IRQs before calling
- * this. The platform_device returned from reserve_pmu() must be passed as
- * a cookie.
  */
-extern int
+extern void
 release_pmu(enum arm_pmu_type type);
 
 /**
@@ -68,24 +69,78 @@
 
 #include <linux/err.h>
 
-static inline struct platform_device *
+static inline int
 reserve_pmu(enum arm_pmu_type type)
 {
-	return ERR_PTR(-ENODEV);
-}
-
-static inline int
-release_pmu(enum arm_pmu_type type)
-{
 	return -ENODEV;
 }
 
-static inline int
-init_pmu(enum arm_pmu_type type)
-{
-	return -ENODEV;
-}
+static inline void
+release_pmu(enum arm_pmu_type type)	{ }
 
 #endif /* CONFIG_CPU_HAS_PMU */
 
+#ifdef CONFIG_HW_PERF_EVENTS
+
+/* The events for a given PMU register set. */
+struct pmu_hw_events {
+	/*
+	 * The events that are active on the PMU for the given index.
+	 */
+	struct perf_event	**events;
+
+	/*
+	 * A 1 bit for an index indicates that the counter is being used for
+	 * an event. A 0 means that the counter can be used.
+	 */
+	unsigned long           *used_mask;
+
+	/*
+	 * Hardware lock to serialize accesses to PMU registers. Needed for the
+	 * read/modify/write sequences.
+	 */
+	raw_spinlock_t		pmu_lock;
+};
+
+struct arm_pmu {
+	struct pmu	pmu;
+	enum arm_perf_pmu_ids id;
+	enum arm_pmu_type type;
+	cpumask_t	active_irqs;
+	const char	*name;
+	irqreturn_t	(*handle_irq)(int irq_num, void *dev);
+	void		(*enable)(struct hw_perf_event *evt, int idx);
+	void		(*disable)(struct hw_perf_event *evt, int idx);
+	int		(*get_event_idx)(struct pmu_hw_events *hw_events,
+					 struct hw_perf_event *hwc);
+	int		(*set_event_filter)(struct hw_perf_event *evt,
+					    struct perf_event_attr *attr);
+	u32		(*read_counter)(int idx);
+	void		(*write_counter)(int idx, u32 val);
+	void		(*start)(void);
+	void		(*stop)(void);
+	void		(*reset)(void *);
+	int		(*map_event)(struct perf_event *event);
+	int		num_events;
+	atomic_t	active_events;
+	struct mutex	reserve_mutex;
+	u64		max_period;
+	struct platform_device	*plat_device;
+	struct pmu_hw_events	*(*get_hw_events)(void);
+};
+
+#define to_arm_pmu(p) (container_of(p, struct arm_pmu, pmu))
+
+int __init armpmu_register(struct arm_pmu *armpmu, char *name, int type);
+
+u64 armpmu_event_update(struct perf_event *event,
+			struct hw_perf_event *hwc,
+			int idx, int overflow);
+
+int armpmu_event_set_period(struct perf_event *event,
+			    struct hw_perf_event *hwc,
+			    int idx);
+
+#endif /* CONFIG_HW_PERF_EVENTS */
+
 #endif /* __ARM_PMU_H__ */
diff --git a/arch/arm/include/asm/proc-fns.h b/arch/arm/include/asm/proc-fns.h
index 633d1cb..9e92cb20 100644
--- a/arch/arm/include/asm/proc-fns.h
+++ b/arch/arm/include/asm/proc-fns.h
@@ -81,6 +81,10 @@
 extern void cpu_do_switch_mm(unsigned long pgd_phys, struct mm_struct *mm);
 extern void cpu_set_pte_ext(pte_t *ptep, pte_t pte, unsigned int ext);
 extern void cpu_reset(unsigned long addr) __attribute__((noreturn));
+
+/* These three are private to arch/arm/kernel/suspend.c */
+extern void cpu_do_suspend(void *);
+extern void cpu_do_resume(void *);
 #else
 #define cpu_proc_init			processor._proc_init
 #define cpu_proc_fin			processor._proc_fin
@@ -89,6 +93,10 @@
 #define cpu_dcache_clean_area		processor.dcache_clean_area
 #define cpu_set_pte_ext			processor.set_pte_ext
 #define cpu_do_switch_mm		processor.switch_mm
+
+/* These three are private to arch/arm/kernel/suspend.c */
+#define cpu_do_suspend			processor.do_suspend
+#define cpu_do_resume			processor.do_resume
 #endif
 
 extern void cpu_resume(void);
diff --git a/arch/arm/include/asm/smp.h b/arch/arm/include/asm/smp.h
index e42d96a..1e5717a 100644
--- a/arch/arm/include/asm/smp.h
+++ b/arch/arm/include/asm/smp.h
@@ -33,6 +33,11 @@
 asmlinkage void do_IPI(int ipinr, struct pt_regs *regs);
 
 /*
+ * Called from C code, this handles an IPI.
+ */
+void handle_IPI(int ipinr, struct pt_regs *regs);
+
+/*
  * Setup the set of possible CPUs (via set_cpu_possible)
  */
 extern void smp_init_cpus(void);
@@ -66,6 +71,12 @@
 extern void platform_smp_prepare_cpus(unsigned int);
 
 /*
+ * Logical CPU mapping.
+ */
+extern int __cpu_logical_map[NR_CPUS];
+#define cpu_logical_map(cpu)	__cpu_logical_map[cpu]
+
+/*
  * Initial data for bringing up a secondary CPU.
  */
 struct secondary_data {
@@ -88,9 +99,4 @@
 extern void arch_send_call_function_single_ipi(int cpu);
 extern void arch_send_call_function_ipi_mask(const struct cpumask *mask);
 
-/*
- * show local interrupt info
- */
-extern void show_local_irqs(struct seq_file *, int);
-
 #endif /* ifndef __ASM_ARM_SMP_H */
diff --git a/arch/arm/include/asm/smp_twd.h b/arch/arm/include/asm/smp_twd.h
index fed9981..ef9ffba9 100644
--- a/arch/arm/include/asm/smp_twd.h
+++ b/arch/arm/include/asm/smp_twd.h
@@ -22,7 +22,7 @@
 
 extern void __iomem *twd_base;
 
-int twd_timer_ack(void);
 void twd_timer_setup(struct clock_event_device *);
+void twd_timer_stop(struct clock_event_device *);
 
 #endif
diff --git a/arch/arm/include/asm/suspend.h b/arch/arm/include/asm/suspend.h
index b0e4e1a..1c0a551 100644
--- a/arch/arm/include/asm/suspend.h
+++ b/arch/arm/include/asm/suspend.h
@@ -1,22 +1,7 @@
 #ifndef __ASM_ARM_SUSPEND_H
 #define __ASM_ARM_SUSPEND_H
 
-#include <asm/memory.h>
-#include <asm/tlbflush.h>
-
 extern void cpu_resume(void);
-
-/*
- * Hide the first two arguments to __cpu_suspend - these are an implementation
- * detail which platform code shouldn't have to know about.
- */
-static inline int cpu_suspend(unsigned long arg, int (*fn)(unsigned long))
-{
-	extern int __cpu_suspend(int, long, unsigned long,
-				 int (*)(unsigned long));
-	int ret = __cpu_suspend(0, PHYS_OFFSET - PAGE_OFFSET, arg, fn);
-	flush_tlb_all();
-	return ret;
-}
+extern int cpu_suspend(unsigned long, int (*)(unsigned long));
 
 #endif
diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h
index 832888d..ed6b049 100644
--- a/arch/arm/include/asm/system.h
+++ b/arch/arm/include/asm/system.h
@@ -62,13 +62,6 @@
 
 #include <asm/outercache.h>
 
-#define __exception	__attribute__((section(".exception.text")))
-#ifdef CONFIG_FUNCTION_GRAPH_TRACER
-#define __exception_irq_entry	__irq_entry
-#else
-#define __exception_irq_entry	__exception
-#endif
-
 struct thread_info;
 struct task_struct;
 
diff --git a/arch/arm/include/asm/topology.h b/arch/arm/include/asm/topology.h
index accbd7c..a7e457e 100644
--- a/arch/arm/include/asm/topology.h
+++ b/arch/arm/include/asm/topology.h
@@ -1,6 +1,39 @@
 #ifndef _ASM_ARM_TOPOLOGY_H
 #define _ASM_ARM_TOPOLOGY_H
 
+#ifdef CONFIG_ARM_CPU_TOPOLOGY
+
+#include <linux/cpumask.h>
+
+struct cputopo_arm {
+	int thread_id;
+	int core_id;
+	int socket_id;
+	cpumask_t thread_sibling;
+	cpumask_t core_sibling;
+};
+
+extern struct cputopo_arm cpu_topology[NR_CPUS];
+
+#define topology_physical_package_id(cpu)	(cpu_topology[cpu].socket_id)
+#define topology_core_id(cpu)		(cpu_topology[cpu].core_id)
+#define topology_core_cpumask(cpu)	(&cpu_topology[cpu].core_sibling)
+#define topology_thread_cpumask(cpu)	(&cpu_topology[cpu].thread_sibling)
+
+#define mc_capable()	(cpu_topology[0].socket_id != -1)
+#define smt_capable()	(cpu_topology[0].thread_id != -1)
+
+void init_cpu_topology(void);
+void store_cpu_topology(unsigned int cpuid);
+const struct cpumask *cpu_coregroup_mask(unsigned int cpu);
+
+#else
+
+static inline void init_cpu_topology(void) { }
+static inline void store_cpu_topology(unsigned int cpuid) { }
+
+#endif
+
 #include <asm-generic/topology.h>
 
 #endif /* _ASM_ARM_TOPOLOGY_H */
diff --git a/arch/arm/kernel/Makefile b/arch/arm/kernel/Makefile
index f7887dc..7cac26c 100644
--- a/arch/arm/kernel/Makefile
+++ b/arch/arm/kernel/Makefile
@@ -29,7 +29,7 @@
 obj-$(CONFIG_ARTHUR)		+= arthur.o
 obj-$(CONFIG_ISA_DMA)		+= dma-isa.o
 obj-$(CONFIG_PCI)		+= bios32.o isa.o
-obj-$(CONFIG_PM_SLEEP)		+= sleep.o
+obj-$(CONFIG_PM_SLEEP)		+= sleep.o suspend.o
 obj-$(CONFIG_HAVE_SCHED_CLOCK)	+= sched_clock.o
 obj-$(CONFIG_SMP)		+= smp.o smp_tlb.o
 obj-$(CONFIG_HAVE_ARM_SCU)	+= smp_scu.o
@@ -43,6 +43,13 @@
 else
 obj-$(CONFIG_KPROBES)		+= kprobes-arm.o
 endif
+obj-$(CONFIG_ARM_KPROBES_TEST)	+= test-kprobes.o
+test-kprobes-objs		:= kprobes-test.o
+ifdef CONFIG_THUMB2_KERNEL
+test-kprobes-objs		+= kprobes-test-thumb.o
+else
+test-kprobes-objs		+= kprobes-test-arm.o
+endif
 obj-$(CONFIG_ATAGS_PROC)	+= atags.o
 obj-$(CONFIG_OABI_COMPAT)	+= sys_oabi-compat.o
 obj-$(CONFIG_ARM_THUMBEE)	+= thumbee.o
@@ -66,6 +73,7 @@
 obj-$(CONFIG_CPU_HAS_PMU)	+= pmu.o
 obj-$(CONFIG_HW_PERF_EVENTS)	+= perf_event.o
 AFLAGS_iwmmxt.o			:= -Wa,-mcpu=iwmmxt
+obj-$(CONFIG_ARM_CPU_TOPOLOGY)  += topology.o
 
 ifneq ($(CONFIG_ARCH_EBSA110),y)
   obj-y		+= io.o
diff --git a/arch/arm/kernel/debug.S b/arch/arm/kernel/debug.S
index bcd66e0..b7685f1 100644
--- a/arch/arm/kernel/debug.S
+++ b/arch/arm/kernel/debug.S
@@ -22,7 +22,7 @@
 #if defined(CONFIG_DEBUG_ICEDCC)
 		@@ debug using ARM EmbeddedICE DCC channel
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		.endm
 
 #if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_V6K) || defined(CONFIG_CPU_V7)
@@ -106,7 +106,7 @@
 
 #ifdef CONFIG_MMU
 		.macro	addruart_current, rx, tmp1, tmp2
-		addruart	\tmp1, \tmp2
+		addruart	\tmp1, \tmp2, \rx
 		mrc		p15, 0, \rx, c1, c0
 		tst		\rx, #1
 		moveq		\rx, \tmp1
diff --git a/arch/arm/kernel/head.S b/arch/arm/kernel/head.S
index 742b610..673c806 100644
--- a/arch/arm/kernel/head.S
+++ b/arch/arm/kernel/head.S
@@ -95,7 +95,7 @@
 	sub	r4, r3, r4			@ (PHYS_OFFSET - PAGE_OFFSET)
 	add	r8, r8, r4			@ PHYS_OFFSET
 #else
-	ldr	r8, =PLAT_PHYS_OFFSET
+	ldr	r8, =PHYS_OFFSET		@ always constant in this case
 #endif
 
 	/*
@@ -234,7 +234,7 @@
 	 * This allows debug messages to be output
 	 * via a serial console before paging_init.
 	 */
-	addruart r7, r3
+	addruart r7, r3, r0
 
 	mov	r3, r3, lsr #20
 	mov	r3, r3, lsl #2
@@ -488,13 +488,8 @@
 	add	r5, r5, r3	@ adjust table end address
 	add	r7, r7, r3	@ adjust __pv_phys_offset address
 	str	r8, [r7]	@ save computed PHYS_OFFSET to __pv_phys_offset
-#ifndef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
 	mov	r6, r3, lsr #24	@ constant for add/sub instructions
 	teq	r3, r6, lsl #24 @ must be 16MiB aligned
-#else
-	mov	r6, r3, lsr #16	@ constant for add/sub instructions
-	teq	r3, r6, lsl #16	@ must be 64kiB aligned
-#endif
 THUMB(	it	ne		@ cross section branch )
 	bne	__error
 	str	r6, [r7, #4]	@ save to __pv_offset
@@ -510,20 +505,8 @@
 	.text
 __fixup_a_pv_table:
 #ifdef CONFIG_THUMB2_KERNEL
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-	lsls	r0, r6, #24
-	lsr	r6, #8
-	beq	1f
-	clz	r7, r0
-	lsr	r0, #24
-	lsl	r0, r7
-	bic	r0, 0x0080
-	lsrs	r7, #1
-	orrcs   r0, #0x0080
-	orr	r0, r0, r7, lsl #12
-#endif
-1:	lsls	r6, #24
-	beq	4f
+	lsls	r6, #24
+	beq	2f
 	clz	r7, r6
 	lsr	r6, #24
 	lsl	r6, r7
@@ -532,43 +515,25 @@
 	orrcs	r6, #0x0080
 	orr	r6, r6, r7, lsl #12
 	orr	r6, #0x4000
-	b	4f
-2:	@ at this point the C flag is always clear
-	add     r7, r3
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-	ldrh	ip, [r7]
-	tst	ip, 0x0400	@ the i bit tells us LS or MS byte
-	beq	3f
-	cmp	r0, #0		@ set C flag, and ...
-	biceq	ip, 0x0400	@ immediate zero value has a special encoding
-	streqh	ip, [r7]	@ that requires the i bit cleared
-#endif
-3:	ldrh	ip, [r7, #2]
+	b	2f
+1:	add     r7, r3
+	ldrh	ip, [r7, #2]
 	and	ip, 0x8f00
-	orrcc	ip, r6	@ mask in offset bits 31-24
-	orrcs	ip, r0	@ mask in offset bits 23-16
+	orr	ip, r6	@ mask in offset bits 31-24
 	strh	ip, [r7, #2]
-4:	cmp	r4, r5
+2:	cmp	r4, r5
 	ldrcc	r7, [r4], #4	@ use branch for delay slot
-	bcc	2b
+	bcc	1b
 	bx	lr
 #else
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-	and	r0, r6, #255	@ offset bits 23-16
-	mov	r6, r6, lsr #8	@ offset bits 31-24
-#else
-	mov	r0, #0		@ just in case...
-#endif
-	b	3f
-2:	ldr	ip, [r7, r3]
+	b	2f
+1:	ldr	ip, [r7, r3]
 	bic	ip, ip, #0x000000ff
-	tst	ip, #0x400	@ rotate shift tells us LS or MS byte
-	orrne	ip, ip, r6	@ mask in offset bits 31-24
-	orreq	ip, ip, r0	@ mask in offset bits 23-16
+	orr	ip, ip, r6	@ mask in offset bits 31-24
 	str	ip, [r7, r3]
-3:	cmp	r4, r5
+2:	cmp	r4, r5
 	ldrcc	r7, [r4], #4	@ use branch for delay slot
-	bcc	2b
+	bcc	1b
 	mov	pc, lr
 #endif
 ENDPROC(__fixup_a_pv_table)
diff --git a/arch/arm/kernel/hw_breakpoint.c b/arch/arm/kernel/hw_breakpoint.c
index a927ca1..814a52a9 100644
--- a/arch/arm/kernel/hw_breakpoint.c
+++ b/arch/arm/kernel/hw_breakpoint.c
@@ -45,7 +45,6 @@
 
 /* Number of BRP/WRP registers on this CPU. */
 static int core_num_brps;
-static int core_num_reserved_brps;
 static int core_num_wrps;
 
 /* Debug architecture version. */
@@ -137,10 +136,11 @@
 	u32 didr;
 
 	/* Do we implement the extended CPUID interface? */
-	if (WARN_ONCE((((read_cpuid_id() >> 16) & 0xf) != 0xf),
-	    "CPUID feature registers not supported. "
-	    "Assuming v6 debug is present.\n"))
+	if (((read_cpuid_id() >> 16) & 0xf) != 0xf) {
+		pr_warning("CPUID feature registers not supported. "
+			   "Assuming v6 debug is present.\n");
 		return ARM_DEBUG_ARCH_V6;
+	}
 
 	ARM_DBG_READ(c0, 0, didr);
 	return (didr >> 16) & 0xf;
@@ -154,10 +154,21 @@
 static int debug_arch_supported(void)
 {
 	u8 arch = get_debug_arch();
-	return arch >= ARM_DEBUG_ARCH_V6 && arch <= ARM_DEBUG_ARCH_V7_ECP14;
+
+	/* We don't support the memory-mapped interface. */
+	return (arch >= ARM_DEBUG_ARCH_V6 && arch <= ARM_DEBUG_ARCH_V7_ECP14) ||
+		arch >= ARM_DEBUG_ARCH_V7_1;
 }
 
-/* Determine number of BRP register available. */
+/* Determine number of WRP registers available. */
+static int get_num_wrp_resources(void)
+{
+	u32 didr;
+	ARM_DBG_READ(c0, 0, didr);
+	return ((didr >> 28) & 0xf) + 1;
+}
+
+/* Determine number of BRP registers available. */
 static int get_num_brp_resources(void)
 {
 	u32 didr;
@@ -176,9 +187,10 @@
 static int get_num_wrps(void)
 {
 	/*
-	 * FIXME: When a watchpoint fires, the only way to work out which
-	 * watchpoint it was is by disassembling the faulting instruction
-	 * and working out the address of the memory access.
+	 * On debug architectures prior to 7.1, when a watchpoint fires, the
+	 * only way to work out which watchpoint it was is by disassembling
+	 * the faulting instruction and working out the address of the memory
+	 * access.
 	 *
 	 * Furthermore, we can only do this if the watchpoint was precise
 	 * since imprecise watchpoints prevent us from calculating register
@@ -192,36 +204,17 @@
 	 * [the ARM ARM states that the DFAR is UNKNOWN, but experience shows
 	 * that it is set on some implementations].
 	 */
+	if (get_debug_arch() < ARM_DEBUG_ARCH_V7_1)
+		return 1;
 
-#if 0
-	int wrps;
-	u32 didr;
-	ARM_DBG_READ(c0, 0, didr);
-	wrps = ((didr >> 28) & 0xf) + 1;
-#endif
-	int wrps = 1;
-
-	if (core_has_mismatch_brps() && wrps >= get_num_brp_resources())
-		wrps = get_num_brp_resources() - 1;
-
-	return wrps;
-}
-
-/* We reserve one breakpoint for each watchpoint. */
-static int get_num_reserved_brps(void)
-{
-	if (core_has_mismatch_brps())
-		return get_num_wrps();
-	return 0;
+	return get_num_wrp_resources();
 }
 
 /* Determine number of usable BRPs available. */
 static int get_num_brps(void)
 {
 	int brps = get_num_brp_resources();
-	if (core_has_mismatch_brps())
-		brps -= get_num_reserved_brps();
-	return brps;
+	return core_has_mismatch_brps() ? brps - 1 : brps;
 }
 
 /*
@@ -239,7 +232,7 @@
 
 	/* Ensure that halting mode is disabled. */
 	if (WARN_ONCE(dscr & ARM_DSCR_HDBGEN,
-			"halting debug mode enabled. Unable to access hardware resources.\n")) {
+		"halting debug mode enabled. Unable to access hardware resources.\n")) {
 		ret = -EPERM;
 		goto out;
 	}
@@ -255,6 +248,7 @@
 		ARM_DBG_WRITE(c1, 0, (dscr | ARM_DSCR_MDBGEN));
 		break;
 	case ARM_DEBUG_ARCH_V7_ECP14:
+	case ARM_DEBUG_ARCH_V7_1:
 		ARM_DBG_WRITE(c2, 2, (dscr | ARM_DSCR_MDBGEN));
 		break;
 	default:
@@ -346,24 +340,10 @@
 		val_base = ARM_BASE_BVR;
 		slots = (struct perf_event **)__get_cpu_var(bp_on_reg);
 		max_slots = core_num_brps;
-		if (info->step_ctrl.enabled) {
-			/* Override the breakpoint data with the step data. */
-			addr = info->trigger & ~0x3;
-			ctrl = encode_ctrl_reg(info->step_ctrl);
-		}
 	} else {
 		/* Watchpoint */
-		if (info->step_ctrl.enabled) {
-			/* Install into the reserved breakpoint region. */
-			ctrl_base = ARM_BASE_BCR + core_num_brps;
-			val_base = ARM_BASE_BVR + core_num_brps;
-			/* Override the watchpoint data with the step data. */
-			addr = info->trigger & ~0x3;
-			ctrl = encode_ctrl_reg(info->step_ctrl);
-		} else {
-			ctrl_base = ARM_BASE_WCR;
-			val_base = ARM_BASE_WVR;
-		}
+		ctrl_base = ARM_BASE_WCR;
+		val_base = ARM_BASE_WVR;
 		slots = (struct perf_event **)__get_cpu_var(wp_on_reg);
 		max_slots = core_num_wrps;
 	}
@@ -382,6 +362,17 @@
 		goto out;
 	}
 
+	/* Override the breakpoint data with the step data. */
+	if (info->step_ctrl.enabled) {
+		addr = info->trigger & ~0x3;
+		ctrl = encode_ctrl_reg(info->step_ctrl);
+		if (info->ctrl.type != ARM_BREAKPOINT_EXECUTE) {
+			i = 0;
+			ctrl_base = ARM_BASE_BCR + core_num_brps;
+			val_base = ARM_BASE_BVR + core_num_brps;
+		}
+	}
+
 	/* Setup the address register. */
 	write_wb_reg(val_base + i, addr);
 
@@ -405,10 +396,7 @@
 		max_slots = core_num_brps;
 	} else {
 		/* Watchpoint */
-		if (info->step_ctrl.enabled)
-			base = ARM_BASE_BCR + core_num_brps;
-		else
-			base = ARM_BASE_WCR;
+		base = ARM_BASE_WCR;
 		slots = (struct perf_event **)__get_cpu_var(wp_on_reg);
 		max_slots = core_num_wrps;
 	}
@@ -426,6 +414,13 @@
 	if (WARN_ONCE(i == max_slots, "Can't find any breakpoint slot\n"))
 		return;
 
+	/* Ensure that we disable the mismatch breakpoint. */
+	if (info->ctrl.type != ARM_BREAKPOINT_EXECUTE &&
+	    info->step_ctrl.enabled) {
+		i = 0;
+		base = ARM_BASE_BCR + core_num_brps;
+	}
+
 	/* Reset the control register. */
 	write_wb_reg(base + i, 0);
 }
@@ -632,10 +627,9 @@
 	 * we can use the mismatch feature as a poor-man's hardware
 	 * single-step, but this only works for per-task breakpoints.
 	 */
-	if (WARN_ONCE(!bp->overflow_handler &&
-		(arch_check_bp_in_kernelspace(bp) || !core_has_mismatch_brps()
-		 || !bp->hw.bp_target),
-			"overflow handler required but none found\n")) {
+	if (!bp->overflow_handler && (arch_check_bp_in_kernelspace(bp) ||
+	    !core_has_mismatch_brps() || !bp->hw.bp_target)) {
+		pr_warning("overflow handler required but none found\n");
 		ret = -EINVAL;
 	}
 out:
@@ -666,34 +660,62 @@
 	arch_install_hw_breakpoint(bp);
 }
 
-static void watchpoint_handler(unsigned long unknown, struct pt_regs *regs)
+static void watchpoint_handler(unsigned long addr, unsigned int fsr,
+			       struct pt_regs *regs)
 {
-	int i;
+	int i, access;
+	u32 val, ctrl_reg, alignment_mask;
 	struct perf_event *wp, **slots;
 	struct arch_hw_breakpoint *info;
+	struct arch_hw_breakpoint_ctrl ctrl;
 
 	slots = (struct perf_event **)__get_cpu_var(wp_on_reg);
 
-	/* Without a disassembler, we can only handle 1 watchpoint. */
-	BUG_ON(core_num_wrps > 1);
-
 	for (i = 0; i < core_num_wrps; ++i) {
 		rcu_read_lock();
 
 		wp = slots[i];
 
-		if (wp == NULL) {
-			rcu_read_unlock();
-			continue;
+		if (wp == NULL)
+			goto unlock;
+
+		info = counter_arch_bp(wp);
+		/*
+		 * The DFAR is an unknown value on debug architectures prior
+		 * to 7.1. Since we only allow a single watchpoint on these
+		 * older CPUs, we can set the trigger to the lowest possible
+		 * faulting address.
+		 */
+		if (debug_arch < ARM_DEBUG_ARCH_V7_1) {
+			BUG_ON(i > 0);
+			info->trigger = wp->attr.bp_addr;
+		} else {
+			if (info->ctrl.len == ARM_BREAKPOINT_LEN_8)
+				alignment_mask = 0x7;
+			else
+				alignment_mask = 0x3;
+
+			/* Check if the watchpoint value matches. */
+			val = read_wb_reg(ARM_BASE_WVR + i);
+			if (val != (addr & ~alignment_mask))
+				goto unlock;
+
+			/* Possible match, check the byte address select. */
+			ctrl_reg = read_wb_reg(ARM_BASE_WCR + i);
+			decode_ctrl_reg(ctrl_reg, &ctrl);
+			if (!((1 << (addr & alignment_mask)) & ctrl.len))
+				goto unlock;
+
+			/* Check that the access type matches. */
+			access = (fsr & ARM_FSR_ACCESS_MASK) ? HW_BREAKPOINT_W :
+				 HW_BREAKPOINT_R;
+			if (!(access & hw_breakpoint_type(wp)))
+				goto unlock;
+
+			/* We have a winner. */
+			info->trigger = addr;
 		}
 
-		/*
-		 * The DFAR is an unknown value. Since we only allow a
-		 * single watchpoint, we can set the trigger to the lowest
-		 * possible faulting address.
-		 */
-		info = counter_arch_bp(wp);
-		info->trigger = wp->attr.bp_addr;
 		pr_debug("watchpoint fired: address = 0x%x\n", info->trigger);
 		perf_bp_event(wp, regs);
 
@@ -705,6 +727,7 @@
 		if (!wp->overflow_handler)
 			enable_single_step(wp, instruction_pointer(regs));
 
+unlock:
 		rcu_read_unlock();
 	}
 }
@@ -717,7 +740,7 @@
 
 	slots = (struct perf_event **)__get_cpu_var(wp_on_reg);
 
-	for (i = 0; i < core_num_reserved_brps; ++i) {
+	for (i = 0; i < core_num_wrps; ++i) {
 		rcu_read_lock();
 
 		wp = slots[i];
@@ -820,7 +843,7 @@
 	case ARM_ENTRY_ASYNC_WATCHPOINT:
 		WARN(1, "Asynchronous watchpoint exception taken. Debugging results may be unreliable\n");
 	case ARM_ENTRY_SYNC_WATCHPOINT:
-		watchpoint_handler(addr, regs);
+		watchpoint_handler(addr, fsr, regs);
 		break;
 	default:
 		ret = 1; /* Unhandled fault. */
@@ -834,11 +857,31 @@
 /*
  * One-time initialisation.
  */
-static void reset_ctrl_regs(void *info)
+static cpumask_t debug_err_mask;
+
+static int debug_reg_trap(struct pt_regs *regs, unsigned int instr)
 {
-	int i, cpu = smp_processor_id();
+	int cpu = smp_processor_id();
+
+	pr_warning("Debug register access (0x%x) caused undefined instruction on CPU %d\n",
+		   instr, cpu);
+
+	/* Set the error flag for this CPU and skip the faulting instruction. */
+	cpumask_set_cpu(cpu, &debug_err_mask);
+	instruction_pointer(regs) += 4;
+	return 0;
+}
+
+static struct undef_hook debug_reg_hook = {
+	.instr_mask	= 0x0fe80f10,
+	.instr_val	= 0x0e000e10,
+	.fn		= debug_reg_trap,
+};
+
+static void reset_ctrl_regs(void *unused)
+{
+	int i, raw_num_brps, err = 0, cpu = smp_processor_id();
 	u32 dbg_power;
-	cpumask_t *cpumask = info;
 
 	/*
 	 * v7 debug contains save and restore registers so that debug state
@@ -848,38 +891,57 @@
 	 * Access Register to avoid taking undefined instruction exceptions
 	 * later on.
 	 */
-	if (debug_arch >= ARM_DEBUG_ARCH_V7_ECP14) {
+	switch (debug_arch) {
+	case ARM_DEBUG_ARCH_V6:
+	case ARM_DEBUG_ARCH_V6_1:
+		/* ARMv6 cores just need to reset the registers. */
+		goto reset_regs;
+	case ARM_DEBUG_ARCH_V7_ECP14:
 		/*
 		 * Ensure sticky power-down is clear (i.e. debug logic is
 		 * powered up).
 		 */
 		asm volatile("mrc p14, 0, %0, c1, c5, 4" : "=r" (dbg_power));
-		if ((dbg_power & 0x1) == 0) {
-			pr_warning("CPU %d debug is powered down!\n", cpu);
-			cpumask_or(cpumask, cpumask, cpumask_of(cpu));
-			return;
-		}
-
+		if ((dbg_power & 0x1) == 0)
+			err = -EPERM;
+		break;
+	case ARM_DEBUG_ARCH_V7_1:
 		/*
-		 * Unconditionally clear the lock by writing a value
-		 * other than 0xC5ACCE55 to the access register.
+		 * Ensure the OS double lock is clear.
 		 */
-		asm volatile("mcr p14, 0, %0, c1, c0, 4" : : "r" (0));
-		isb();
-
-		/*
-		 * Clear any configured vector-catch events before
-		 * enabling monitor mode.
-		 */
-		asm volatile("mcr p14, 0, %0, c0, c7, 0" : : "r" (0));
-		isb();
+		asm volatile("mrc p14, 0, %0, c1, c3, 4" : "=r" (dbg_power));
+		if ((dbg_power & 0x1) == 1)
+			err = -EPERM;
+		break;
 	}
 
+	if (err) {
+		pr_warning("CPU %d debug is powered down!\n", cpu);
+		cpumask_or(&debug_err_mask, &debug_err_mask, cpumask_of(cpu));
+		return;
+	}
+
+	/*
+	 * Unconditionally clear the lock by writing a value
+	 * other than 0xC5ACCE55 to the access register.
+	 */
+	asm volatile("mcr p14, 0, %0, c1, c0, 4" : : "r" (0));
+	isb();
+
+	/*
+	 * Clear any configured vector-catch events before
+	 * enabling monitor mode.
+	 */
+	asm volatile("mcr p14, 0, %0, c0, c7, 0" : : "r" (0));
+	isb();
+
+reset_regs:
 	if (enable_monitor_mode())
 		return;
 
 	/* We must also reset any reserved registers. */
-	for (i = 0; i < core_num_brps + core_num_reserved_brps; ++i) {
+	raw_num_brps = get_num_brp_resources();
+	for (i = 0; i < raw_num_brps; ++i) {
 		write_wb_reg(ARM_BASE_BCR + i, 0UL);
 		write_wb_reg(ARM_BASE_BVR + i, 0UL);
 	}
@@ -895,6 +957,7 @@
 {
 	if (action == CPU_ONLINE)
 		smp_call_function_single((int)cpu, reset_ctrl_regs, NULL, 1);
+
 	return NOTIFY_OK;
 }
 
@@ -905,7 +968,6 @@
 static int __init arch_hw_breakpoint_init(void)
 {
 	u32 dscr;
-	cpumask_t cpumask = { CPU_BITS_NONE };
 
 	debug_arch = get_debug_arch();
 
@@ -916,28 +978,31 @@
 
 	/* Determine how many BRPs/WRPs are available. */
 	core_num_brps = get_num_brps();
-	core_num_reserved_brps = get_num_reserved_brps();
 	core_num_wrps = get_num_wrps();
 
-	pr_info("found %d breakpoint and %d watchpoint registers.\n",
-		core_num_brps + core_num_reserved_brps, core_num_wrps);
-
-	if (core_num_reserved_brps)
-		pr_info("%d breakpoint(s) reserved for watchpoint "
-				"single-step.\n", core_num_reserved_brps);
+	/*
+	 * We need to tread carefully here because DBGSWENABLE may be
+	 * driven low on this core and there isn't an architected way to
+	 * determine that.
+	 */
+	register_undef_hook(&debug_reg_hook);
 
 	/*
 	 * Reset the breakpoint resources. We assume that a halting
 	 * debugger will leave the world in a nice state for us.
 	 */
-	on_each_cpu(reset_ctrl_regs, &cpumask, 1);
-	if (!cpumask_empty(&cpumask)) {
+	on_each_cpu(reset_ctrl_regs, NULL, 1);
+	unregister_undef_hook(&debug_reg_hook);
+	if (!cpumask_empty(&debug_err_mask)) {
 		core_num_brps = 0;
-		core_num_reserved_brps = 0;
 		core_num_wrps = 0;
 		return 0;
 	}
 
+	pr_info("found %d " "%s" "breakpoint and %d watchpoint registers.\n",
+		core_num_brps, core_has_mismatch_brps() ? "(+1 reserved) " :
+		"", core_num_wrps);
+
 	ARM_DBG_READ(c1, 0, dscr);
 	if (dscr & ARM_DSCR_HDBGEN) {
 		max_watchpoint_len = 4;
diff --git a/arch/arm/kernel/irq.c b/arch/arm/kernel/irq.c
index de3dcab8..7cb2926 100644
--- a/arch/arm/kernel/irq.c
+++ b/arch/arm/kernel/irq.c
@@ -35,8 +35,8 @@
 #include <linux/list.h>
 #include <linux/kallsyms.h>
 #include <linux/proc_fs.h>
-#include <linux/ftrace.h>
 
+#include <asm/exception.h>
 #include <asm/system.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/irq.h>
@@ -59,9 +59,6 @@
 #ifdef CONFIG_SMP
 	show_ipi_list(p, prec);
 #endif
-#ifdef CONFIG_LOCAL_TIMERS
-	show_local_irqs(p, prec);
-#endif
 	seq_printf(p, "%*s: %10lu\n", prec, "Err", irq_err_count);
 	return 0;
 }
diff --git a/arch/arm/kernel/kprobes-arm.c b/arch/arm/kernel/kprobes-arm.c
index 79203ee..9fe8910 100644
--- a/arch/arm/kernel/kprobes-arm.c
+++ b/arch/arm/kernel/kprobes-arm.c
@@ -60,6 +60,7 @@
 
 #include <linux/kernel.h>
 #include <linux/kprobes.h>
+#include <linux/module.h>
 
 #include "kprobes.h"
 
@@ -971,6 +972,9 @@
 
 	DECODE_END
 };
+#ifdef CONFIG_ARM_KPROBES_TEST_MODULE
+EXPORT_SYMBOL_GPL(kprobe_decode_arm_table);
+#endif
 
 static void __kprobes arm_singlestep(struct kprobe *p, struct pt_regs *regs)
 {
diff --git a/arch/arm/kernel/kprobes-test-arm.c b/arch/arm/kernel/kprobes-test-arm.c
new file mode 100644
index 0000000..fc82de8
--- /dev/null
+++ b/arch/arm/kernel/kprobes-test-arm.c
@@ -0,0 +1,1323 @@
+/*
+ * arch/arm/kernel/kprobes-test-arm.c
+ *
+ * Copyright (C) 2011 Jon Medhurst <tixy@yxit.co.uk>.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+
+#include "kprobes-test.h"
+
+
+#define TEST_ISA "32"
+
+#define TEST_ARM_TO_THUMB_INTERWORK_R(code1, reg, val, code2)	\
+	TESTCASE_START(code1 #reg code2)			\
+	TEST_ARG_REG(reg, val)					\
+	TEST_ARG_REG(14, 99f)					\
+	TEST_ARG_END("")					\
+	"50:	nop			\n\t"			\
+	"1:	"code1 #reg code2"	\n\t"			\
+	"	bx	lr		\n\t"			\
+	".thumb				\n\t"			\
+	"3:	adr	lr, 2f		\n\t"			\
+	"	bx	lr		\n\t"			\
+	".arm				\n\t"			\
+	"2:	nop			\n\t"			\
+	TESTCASE_END
+
+#define TEST_ARM_TO_THUMB_INTERWORK_P(code1, reg, val, code2)	\
+	TESTCASE_START(code1 #reg code2)			\
+	TEST_ARG_PTR(reg, val)					\
+	TEST_ARG_REG(14, 99f)					\
+	TEST_ARG_MEM(15, 3f+1)					\
+	TEST_ARG_END("")					\
+	"50:	nop			\n\t"			\
+	"1:	"code1 #reg code2"	\n\t"			\
+	"	bx	lr		\n\t"			\
+	".thumb				\n\t"			\
+	"3:	adr	lr, 2f		\n\t"			\
+	"	bx	lr		\n\t"			\
+	".arm				\n\t"			\
+	"2:	nop			\n\t"			\
+	TESTCASE_END
+
+
+void kprobe_arm_test_cases(void)
+{
+	kprobe_test_flags = 0;
+
+	TEST_GROUP("Data-processing (register), (register-shifted register), (immediate)")
+
+#define _DATA_PROCESSING_DNM(op,s,val)						\
+	TEST_RR(  op "eq" s "	r0,  r",1, VAL1,", r",2, val, "")		\
+	TEST_RR(  op "ne" s "	r1,  r",1, VAL1,", r",2, val, ", lsl #3")	\
+	TEST_RR(  op "cs" s "	r2,  r",3, VAL1,", r",2, val, ", lsr #4")	\
+	TEST_RR(  op "cc" s "	r3,  r",3, VAL1,", r",2, val, ", asr #5")	\
+	TEST_RR(  op "mi" s "	r4,  r",5, VAL1,", r",2, N(val),", asr #6")	\
+	TEST_RR(  op "pl" s "	r5,  r",5, VAL1,", r",2, val, ", ror #7")	\
+	TEST_RR(  op "vs" s "	r6,  r",7, VAL1,", r",2, val, ", rrx")		\
+	TEST_R(   op "vc" s "	r6,  r",7, VAL1,", pc, lsl #3")			\
+	TEST_R(   op "vc" s "	r6,  r",7, VAL1,", sp, lsr #4")			\
+	TEST_R(   op "vc" s "	r6,  pc, r",7, VAL1,", asr #5")			\
+	TEST_R(   op "vc" s "	r6,  sp, r",7, VAL1,", ror #6")			\
+	TEST_RRR( op "hi" s "	r8,  r",9, VAL1,", r",14,val, ", lsl r",0, 3,"")\
+	TEST_RRR( op "ls" s "	r9,  r",9, VAL1,", r",14,val, ", lsr r",7, 4,"")\
+	TEST_RRR( op "ge" s "	r10, r",11,VAL1,", r",14,val, ", asr r",7, 5,"")\
+	TEST_RRR( op "lt" s "	r11, r",11,VAL1,", r",14,N(val),", asr r",7, 6,"")\
+	TEST_RR(  op "gt" s "	r12, r13"       ", r",14,val, ", ror r",14,7,"")\
+	TEST_RR(  op "le" s "	r14, r",0, val, ", r13"       ", lsl r",14,8,"")\
+	TEST_RR(  op s "	r12, pc"        ", r",14,val, ", ror r",14,7,"")\
+	TEST_RR(  op s "	r14, r",0, val, ", pc"        ", lsl r",14,8,"")\
+	TEST_R(   op "eq" s "	r0,  r",11,VAL1,", #0xf5")			\
+	TEST_R(   op "ne" s "	r11, r",0, VAL1,", #0xf5000000")		\
+	TEST_R(   op s "	r7,  r",8, VAL2,", #0x000af000")		\
+	TEST(     op s "	r4,  pc"        ", #0x00005a00")
+
+#define DATA_PROCESSING_DNM(op,val)		\
+	_DATA_PROCESSING_DNM(op,"",val)		\
+	_DATA_PROCESSING_DNM(op,"s",val)
+
+#define DATA_PROCESSING_NM(op,val)						\
+	TEST_RR(  op "ne	r",1, VAL1,", r",2, val, "")			\
+	TEST_RR(  op "eq	r",1, VAL1,", r",2, val, ", lsl #3")		\
+	TEST_RR(  op "cc	r",3, VAL1,", r",2, val, ", lsr #4")		\
+	TEST_RR(  op "cs	r",3, VAL1,", r",2, val, ", asr #5")		\
+	TEST_RR(  op "pl	r",5, VAL1,", r",2, N(val),", asr #6")		\
+	TEST_RR(  op "mi	r",5, VAL1,", r",2, val, ", ror #7")		\
+	TEST_RR(  op "vc	r",7, VAL1,", r",2, val, ", rrx")		\
+	TEST_R (  op "vs	r",7, VAL1,", pc, lsl #3")			\
+	TEST_R (  op "vs	r",7, VAL1,", sp, lsr #4")			\
+	TEST_R(   op "vs	pc, r",7, VAL1,", asr #5")			\
+	TEST_R(   op "vs	sp, r",7, VAL1,", ror #6")			\
+	TEST_RRR( op "ls	r",9, VAL1,", r",14,val, ", lsl r",0, 3,"")	\
+	TEST_RRR( op "hi	r",9, VAL1,", r",14,val, ", lsr r",7, 4,"")	\
+	TEST_RRR( op "lt	r",11,VAL1,", r",14,val, ", asr r",7, 5,"")	\
+	TEST_RRR( op "ge	r",11,VAL1,", r",14,N(val),", asr r",7, 6,"")	\
+	TEST_RR(  op "le	r13"       ", r",14,val, ", ror r",14,7,"")	\
+	TEST_RR(  op "gt	r",0, val, ", r13"       ", lsl r",14,8,"")	\
+	TEST_RR(  op "	pc"        ", r",14,val, ", ror r",14,7,"")		\
+	TEST_RR(  op "	r",0, val, ", pc"        ", lsl r",14,8,"")		\
+	TEST_R(   op "eq	r",11,VAL1,", #0xf5")				\
+	TEST_R(   op "ne	r",0, VAL1,", #0xf5000000")			\
+	TEST_R(   op "	r",8, VAL2,", #0x000af000")
+
+#define _DATA_PROCESSING_DM(op,s,val)					\
+	TEST_R(   op "eq" s "	r0,  r",1, val, "")			\
+	TEST_R(   op "ne" s "	r1,  r",1, val, ", lsl #3")		\
+	TEST_R(   op "cs" s "	r2,  r",3, val, ", lsr #4")		\
+	TEST_R(   op "cc" s "	r3,  r",3, val, ", asr #5")		\
+	TEST_R(   op "mi" s "	r4,  r",5, N(val),", asr #6")		\
+	TEST_R(   op "pl" s "	r5,  r",5, val, ", ror #7")		\
+	TEST_R(   op "vs" s "	r6,  r",10,val, ", rrx")		\
+	TEST(     op "vs" s "	r7,  pc, lsl #3")			\
+	TEST(     op "vs" s "	r7,  sp, lsr #4")			\
+	TEST_RR(  op "vc" s "	r8,  r",7, val, ", lsl r",0, 3,"")	\
+	TEST_RR(  op "hi" s "	r9,  r",9, val, ", lsr r",7, 4,"")	\
+	TEST_RR(  op "ls" s "	r10, r",9, val, ", asr r",7, 5,"")	\
+	TEST_RR(  op "ge" s "	r11, r",11,N(val),", asr r",7, 6,"")	\
+	TEST_RR(  op "lt" s "	r12, r",11,val, ", ror r",14,7,"")	\
+	TEST_R(   op "gt" s "	r14, r13"       ", lsl r",14,8,"")	\
+	TEST_R(   op "le" s "	r14, pc"        ", lsl r",14,8,"")	\
+	TEST(     op "eq" s "	r0,  #0xf5")				\
+	TEST(     op "ne" s "	r11, #0xf5000000")			\
+	TEST(     op s "	r7,  #0x000af000")			\
+	TEST(     op s "	r4,  #0x00005a00")
+
+#define DATA_PROCESSING_DM(op,val)		\
+	_DATA_PROCESSING_DM(op,"",val)		\
+	_DATA_PROCESSING_DM(op,"s",val)
+
+	DATA_PROCESSING_DNM("and",0xf00f00ff)
+	DATA_PROCESSING_DNM("eor",0xf00f00ff)
+	DATA_PROCESSING_DNM("sub",VAL2)
+	DATA_PROCESSING_DNM("rsb",VAL2)
+	DATA_PROCESSING_DNM("add",VAL2)
+	DATA_PROCESSING_DNM("adc",VAL2)
+	DATA_PROCESSING_DNM("sbc",VAL2)
+	DATA_PROCESSING_DNM("rsc",VAL2)
+	DATA_PROCESSING_NM("tst",0xf00f00ff)
+	DATA_PROCESSING_NM("teq",0xf00f00ff)
+	DATA_PROCESSING_NM("cmp",VAL2)
+	DATA_PROCESSING_NM("cmn",VAL2)
+	DATA_PROCESSING_DNM("orr",0xf00f00ff)
+	DATA_PROCESSING_DM("mov",VAL2)
+	DATA_PROCESSING_DNM("bic",0xf00f00ff)
+	DATA_PROCESSING_DM("mvn",VAL2)
+
+	TEST("mov	ip, sp") /* This has special case emulation code */
+
+	TEST_SUPPORTED("mov	pc, #0x1000");
+	TEST_SUPPORTED("mov	sp, #0x1000");
+	TEST_SUPPORTED("cmp	pc, #0x1000");
+	TEST_SUPPORTED("cmp	sp, #0x1000");
+
+	/* Data-processing with PC as shift*/
+	TEST_UNSUPPORTED(".word 0xe15c0f1e	@ cmp	r12, r14, asl pc")
+	TEST_UNSUPPORTED(".word 0xe1a0cf1e	@ mov	r12, r14, asl pc")
+	TEST_UNSUPPORTED(".word 0xe08caf1e	@ add	r10, r12, r14, asl pc")
+
+	/* Data-processing with PC as shift*/
+	TEST_UNSUPPORTED("movs	pc, r1")
+	TEST_UNSUPPORTED("movs	pc, r1, lsl r2")
+	TEST_UNSUPPORTED("movs	pc, #0x10000")
+	TEST_UNSUPPORTED("adds	pc, lr, r1")
+	TEST_UNSUPPORTED("adds	pc, lr, r1, lsl r2")
+	TEST_UNSUPPORTED("adds	pc, lr, #4")
+
+	/* Data-processing with SP as target */
+	TEST("add	sp, sp, #16")
+	TEST("sub	sp, sp, #8")
+	TEST("bic	sp, sp, #0x20")
+	TEST("orr	sp, sp, #0x20")
+	TEST_PR( "add	sp, r",10,0,", r",11,4,"")
+	TEST_PRR("add	sp, r",10,0,", r",11,4,", asl r",12,1,"")
+	TEST_P(  "mov	sp, r",10,0,"")
+	TEST_PR( "mov	sp, r",10,0,", asl r",12,0,"")
+
+	/* Data-processing with PC as target */
+	TEST_BF(   "add	pc, pc, #2f-1b-8")
+	TEST_BF_R ("add	pc, pc, r",14,2f-1f-8,"")
+	TEST_BF_R ("add	pc, r",14,2f-1f-8,", pc")
+	TEST_BF_R ("mov	pc, r",0,2f,"")
+	TEST_BF_RR("mov	pc, r",0,2f,", asl r",1,0,"")
+	TEST_BB(   "sub	pc, pc, #1b-2b+8")
+#if __LINUX_ARM_ARCH__ >= 6
+	TEST_BB(   "sub	pc, pc, #1b-2b+8-2") /* UNPREDICTABLE before ARMv6 */
+#endif
+	TEST_BB_R( "sub	pc, pc, r",14, 1f-2f+8,"")
+	TEST_BB_R( "rsb	pc, r",14,1f-2f+8,", pc")
+	TEST_RR(   "add	pc, pc, r",10,-2,", asl r",11,1,"")
+#ifdef CONFIG_THUMB2_KERNEL
+	TEST_ARM_TO_THUMB_INTERWORK_R("add	pc, pc, r",0,3f-1f-8+1,"")
+	TEST_ARM_TO_THUMB_INTERWORK_R("sub	pc, r",0,3f+8+1,", #8")
+#endif
+	TEST_GROUP("Miscellaneous instructions")
+
+	TEST("mrs	r0, cpsr")
+	TEST("mrspl	r7, cpsr")
+	TEST("mrs	r14, cpsr")
+	TEST_UNSUPPORTED(".word 0xe10ff000	@ mrs r15, cpsr")
+	TEST_UNSUPPORTED("mrs	r0, spsr")
+	TEST_UNSUPPORTED("mrs	lr, spsr")
+
+	TEST_UNSUPPORTED("msr	cpsr, r0")
+	TEST_UNSUPPORTED("msr	cpsr_f, lr")
+	TEST_UNSUPPORTED("msr	spsr, r0")
+
+	TEST_BF_R("bx	r",0,2f,"")
+	TEST_BB_R("bx	r",7,2f,"")
+	TEST_BF_R("bxeq	r",14,2f,"")
+
+	TEST_R("clz	r0, r",0, 0x0,"")
+	TEST_R("clzeq	r7, r",14,0x1,"")
+	TEST_R("clz	lr, r",7, 0xffffffff,"")
+	TEST(  "clz	r4, sp")
+	TEST_UNSUPPORTED(".word 0x016fff10	@ clz pc, r0")
+	TEST_UNSUPPORTED(".word 0x016f0f1f	@ clz r0, pc")
+
+#if __LINUX_ARM_ARCH__ >= 6
+	TEST_UNSUPPORTED("bxj	r0")
+#endif
+
+	TEST_BF_R("blx	r",0,2f,"")
+	TEST_BB_R("blx	r",7,2f,"")
+	TEST_BF_R("blxeq	r",14,2f,"")
+	TEST_UNSUPPORTED(".word 0x0120003f	@ blx pc")
+
+	TEST_RR(   "qadd	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(   "qaddvs	lr, r",9, VAL2,", r",8, VAL1,"")
+	TEST_R(    "qadd	lr, r",9, VAL2,", r13")
+	TEST_RR(   "qsub	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(   "qsubvs	lr, r",9, VAL2,", r",8, VAL1,"")
+	TEST_R(    "qsub	lr, r",9, VAL2,", r13")
+	TEST_RR(   "qdadd	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(   "qdaddvs	lr, r",9, VAL2,", r",8, VAL1,"")
+	TEST_R(    "qdadd	lr, r",9, VAL2,", r13")
+	TEST_RR(   "qdsub	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(   "qdsubvs	lr, r",9, VAL2,", r",8, VAL1,"")
+	TEST_R(    "qdsub	lr, r",9, VAL2,", r13")
+	TEST_UNSUPPORTED(".word 0xe101f050	@ qadd pc, r0, r1")
+	TEST_UNSUPPORTED(".word 0xe121f050	@ qsub pc, r0, r1")
+	TEST_UNSUPPORTED(".word 0xe141f050	@ qdadd pc, r0, r1")
+	TEST_UNSUPPORTED(".word 0xe161f050	@ qdsub pc, r0, r1")
+	TEST_UNSUPPORTED(".word 0xe16f2050	@ qdsub r2, r0, pc")
+	TEST_UNSUPPORTED(".word 0xe161205f	@ qdsub r2, pc, r1")
+
+	TEST_UNSUPPORTED("bkpt	0xffff")
+	TEST_UNSUPPORTED("bkpt	0x0000")
+
+	TEST_UNSUPPORTED(".word 0xe1600070 @ smc #0")
+
+	TEST_GROUP("Halfword multiply and multiply-accumulate")
+
+	TEST_RRR(    "smlabb	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(    "smlabbge	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RR(     "smlabb	lr, r",1, VAL2,", r",2, VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe10f3281 @ smlabb pc, r1, r2, r3")
+	TEST_RRR(    "smlatb	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(    "smlatbge	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RR(     "smlatb	lr, r",1, VAL2,", r",2, VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe10f32a1 @ smlatb pc, r1, r2, r3")
+	TEST_RRR(    "smlabt	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(    "smlabtge	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RR(     "smlabt	lr, r",1, VAL2,", r",2, VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe10f32c1 @ smlabt pc, r1, r2, r3")
+	TEST_RRR(    "smlatt	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(    "smlattge	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RR(     "smlatt	lr, r",1, VAL2,", r",2, VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe10f32e1 @ smlatt pc, r1, r2, r3")
+
+	TEST_RRR(    "smlawb	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(    "smlawbge	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RR(     "smlawb	lr, r",1, VAL2,", r",2, VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe12f3281 @ smlawb pc, r1, r2, r3")
+	TEST_RRR(    "smlawt	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(    "smlawtge	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RR(     "smlawt	lr, r",1, VAL2,", r",2, VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe12f32c1 @ smlawt pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe12032cf @ smlawt r0, pc, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe1203fc1 @ smlawt r0, r1, pc, r3")
+	TEST_UNSUPPORTED(".word 0xe120f2c1 @ smlawt r0, r1, r2, pc")
+
+	TEST_RR(    "smulwb	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smulwbge	r7, r",8, VAL3,", r",9, VAL1,"")
+	TEST_R(     "smulwb	lr, r",1, VAL2,", r13")
+	TEST_UNSUPPORTED(".word 0xe12f02a1 @ smulwb pc, r1, r2")
+	TEST_RR(    "smulwt	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smulwtge	r7, r",8, VAL3,", r",9, VAL1,"")
+	TEST_R(     "smulwt	lr, r",1, VAL2,", r13")
+	TEST_UNSUPPORTED(".word 0xe12f02e1 @ smulwt pc, r1, r2")
+
+	TEST_RRRR(  "smlalbb	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR(  "smlalbble	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRR(   "smlalbb	r",14,VAL3,", r",7, VAL4,", r",5, VAL1,", r13")
+	TEST_UNSUPPORTED(".word 0xe14f1382 @ smlalbb pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe141f382 @ smlalbb r1, pc, r2, r3")
+	TEST_RRRR(  "smlaltb	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR(  "smlaltble	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRR(   "smlaltb	r",14,VAL3,", r",7, VAL4,", r",5, VAL1,", r13")
+	TEST_UNSUPPORTED(".word 0xe14f13a2 @ smlaltb pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe141f3a2 @ smlaltb r1, pc, r2, r3")
+	TEST_RRRR(  "smlalbt	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR(  "smlalbtle	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRR(   "smlalbt	r",14,VAL3,", r",7, VAL4,", r",5, VAL1,", r13")
+	TEST_UNSUPPORTED(".word 0xe14f13c2 @ smlalbt pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe141f3c2 @ smlalbt r1, pc, r2, r3")
+	TEST_RRRR(  "smlaltt	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR(  "smlalttle	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRR(   "smlaltt	r",14,VAL3,", r",7, VAL4,", r",5, VAL1,", r13")
+	TEST_UNSUPPORTED(".word 0xe14f13e2 @ smlalbb pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe140f3e2 @ smlalbb r0, pc, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe14013ef @ smlalbb r0, r1, pc, r3")
+	TEST_UNSUPPORTED(".word 0xe1401fe2 @ smlalbb r0, r1, r2, pc")
+
+	TEST_RR(    "smulbb	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smulbbge	r7, r",8, VAL3,", r",9, VAL1,"")
+	TEST_R(     "smulbb	lr, r",1, VAL2,", r13")
+	TEST_UNSUPPORTED(".word 0xe16f0281 @ smulbb pc, r1, r2")
+	TEST_RR(    "smultb	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smultbge	r7, r",8, VAL3,", r",9, VAL1,"")
+	TEST_R(     "smultb	lr, r",1, VAL2,", r13")
+	TEST_UNSUPPORTED(".word 0xe16f02a1 @ smultb pc, r1, r2")
+	TEST_RR(    "smulbt	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smulbtge	r7, r",8, VAL3,", r",9, VAL1,"")
+	TEST_R(     "smulbt	lr, r",1, VAL2,", r13")
+	TEST_UNSUPPORTED(".word 0xe16f02c1 @ smultb pc, r1, r2")
+	TEST_RR(    "smultt	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smulttge	r7, r",8, VAL3,", r",9, VAL1,"")
+	TEST_R(     "smultt	lr, r",1, VAL2,", r13")
+	TEST_UNSUPPORTED(".word 0xe16f02e1 @ smultt pc, r1, r2")
+	TEST_UNSUPPORTED(".word 0xe16002ef @ smultt r0, pc, r2")
+	TEST_UNSUPPORTED(".word 0xe1600fe1 @ smultt r0, r1, pc")
+
+	TEST_GROUP("Multiply and multiply-accumulate")
+
+	TEST_RR(    "mul	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "mulls	r7, r",8, VAL2,", r",9, VAL2,"")
+	TEST_R(     "mul	lr, r",4, VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe00f0291 @ mul pc, r1, r2")
+	TEST_UNSUPPORTED(".word 0xe000029f @ mul r0, pc, r2")
+	TEST_UNSUPPORTED(".word 0xe0000f91 @ mul r0, r1, pc")
+	TEST_RR(    "muls	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "mullss	r7, r",8, VAL2,", r",9, VAL2,"")
+	TEST_R(     "muls	lr, r",4, VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe01f0291 @ muls pc, r1, r2")
+
+	TEST_RRR(    "mla	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(    "mlahi	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RR(     "mla	lr, r",1, VAL2,", r",2, VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe02f3291 @ mla pc, r1, r2, r3")
+	TEST_RRR(    "mlas	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(    "mlahis	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RR(     "mlas	lr, r",1, VAL2,", r",2, VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe03f3291 @ mlas pc, r1, r2, r3")
+
+#if __LINUX_ARM_ARCH__ >= 6
+	TEST_RR(  "umaal	r0, r1, r",2, VAL1,", r",3, VAL2,"")
+	TEST_RR(  "umaalls	r7, r8, r",9, VAL2,", r",10, VAL1,"")
+	TEST_R(   "umaal	lr, r12, r",11,VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe041f392 @ umaal pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe04f0392 @ umaal r0, pc, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe0500090 @ undef")
+	TEST_UNSUPPORTED(".word 0xe05fff9f @ undef")
+
+	TEST_RRR(  "mls		r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(  "mlshi	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RR(   "mls		lr, r",1, VAL2,", r",2, VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe06f3291 @ mls pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe060329f @ mls r0, pc, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe0603f91 @ mls r0, r1, pc, r3")
+	TEST_UNSUPPORTED(".word 0xe060f291 @ mls r0, r1, r2, pc")
+#endif
+
+	TEST_UNSUPPORTED(".word 0xe0700090 @ undef")
+	TEST_UNSUPPORTED(".word 0xe07fff9f @ undef")
+
+	TEST_RR(  "umull	r0, r1, r",2, VAL1,", r",3, VAL2,"")
+	TEST_RR(  "umullls	r7, r8, r",9, VAL2,", r",10, VAL1,"")
+	TEST_R(   "umull	lr, r12, r",11,VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe081f392 @ umull pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe08f1392 @ umull r1, pc, r2, r3")
+	TEST_RR(  "umulls	r0, r1, r",2, VAL1,", r",3, VAL2,"")
+	TEST_RR(  "umulllss	r7, r8, r",9, VAL2,", r",10, VAL1,"")
+	TEST_R(   "umulls	lr, r12, r",11,VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe091f392 @ umulls pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe09f1392 @ umulls r1, pc, r2, r3")
+
+	TEST_RRRR(  "umlal	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR(  "umlalle	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRR(   "umlal	r",14,VAL3,", r",7, VAL4,", r",5, VAL1,", r13")
+	TEST_UNSUPPORTED(".word 0xe0af1392 @ umlal pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe0a1f392 @ umlal r1, pc, r2, r3")
+	TEST_RRRR(  "umlals	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR(  "umlalles	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRR(   "umlals	r",14,VAL3,", r",7, VAL4,", r",5, VAL1,", r13")
+	TEST_UNSUPPORTED(".word 0xe0bf1392 @ umlals pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe0b1f392 @ umlals r1, pc, r2, r3")
+
+	TEST_RR(  "smull	r0, r1, r",2, VAL1,", r",3, VAL2,"")
+	TEST_RR(  "smullls	r7, r8, r",9, VAL2,", r",10, VAL1,"")
+	TEST_R(   "smull	lr, r12, r",11,VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe0c1f392 @ smull pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe0cf1392 @ smull r1, pc, r2, r3")
+	TEST_RR(  "smulls	r0, r1, r",2, VAL1,", r",3, VAL2,"")
+	TEST_RR(  "smulllss	r7, r8, r",9, VAL2,", r",10, VAL1,"")
+	TEST_R(   "smulls	lr, r12, r",11,VAL3,", r13")
+	TEST_UNSUPPORTED(".word 0xe0d1f392 @ smulls pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe0df1392 @ smulls r1, pc, r2, r3")
+
+	TEST_RRRR(  "smlal	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR(  "smlalle	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRR(   "smlal	r",14,VAL3,", r",7, VAL4,", r",5, VAL1,", r13")
+	TEST_UNSUPPORTED(".word 0xe0ef1392 @ smlal pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe0e1f392 @ smlal r1, pc, r2, r3")
+	TEST_RRRR(  "smlals	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR(  "smlalles	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRR(   "smlals	r",14,VAL3,", r",7, VAL4,", r",5, VAL1,", r13")
+	TEST_UNSUPPORTED(".word 0xe0ff1392 @ smlals pc, r1, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe0f0f392 @ smlals r0, pc, r2, r3")
+	TEST_UNSUPPORTED(".word 0xe0f0139f @ smlals r0, r1, pc, r3")
+	TEST_UNSUPPORTED(".word 0xe0f01f92 @ smlals r0, r1, r2, pc")
+
+	TEST_GROUP("Synchronization primitives")
+
+	/*
+	 * Use hard coded constants for SWP instructions to avoid warnings
+	 * about deprecated instructions.
+	 */
+	TEST_RP( ".word 0xe108e097 @ swp	lr, r",7,VAL2,", [r",8,0,"]")
+	TEST_R(  ".word 0x610d0091 @ swpvs	r0, r",1,VAL1,", [sp]")
+	TEST_RP( ".word 0xe10cd09e @ swp	sp, r",14,VAL2,", [r",12,13*4,"]")
+	TEST_UNSUPPORTED(".word 0xe102f091 @ swp pc, r1, [r2]")
+	TEST_UNSUPPORTED(".word 0xe102009f @ swp r0, pc, [r2]")
+	TEST_UNSUPPORTED(".word 0xe10f0091 @ swp r0, r1, [pc]")
+	TEST_RP( ".word 0xe148e097 @ swpb	lr, r",7,VAL2,", [r",8,0,"]")
+	TEST_R(  ".word 0x614d0091 @ swpvsb	r0, r",1,VAL1,", [sp]")
+	TEST_UNSUPPORTED(".word 0xe142f091 @ swpb pc, r1, [r2]")
+
+	TEST_UNSUPPORTED(".word	0xe1100090") /* Unallocated space */
+	TEST_UNSUPPORTED(".word	0xe1200090") /* Unallocated space */
+	TEST_UNSUPPORTED(".word	0xe1300090") /* Unallocated space */
+	TEST_UNSUPPORTED(".word	0xe1500090") /* Unallocated space */
+	TEST_UNSUPPORTED(".word	0xe1600090") /* Unallocated space */
+	TEST_UNSUPPORTED(".word	0xe1700090") /* Unallocated space */
+#if __LINUX_ARM_ARCH__ >= 6
+	TEST_UNSUPPORTED("ldrex	r2, [sp]")
+	TEST_UNSUPPORTED("strexd	r0, r2, r3, [sp]")
+	TEST_UNSUPPORTED("ldrexd	r2, r3, [sp]")
+	TEST_UNSUPPORTED("strexb	r0, r2, [sp]")
+	TEST_UNSUPPORTED("ldrexb	r2, [sp]")
+	TEST_UNSUPPORTED("strexh	r0, r2, [sp]")
+	TEST_UNSUPPORTED("ldrexh	r2, [sp]")
+#endif
+	TEST_GROUP("Extra load/store instructions")
+
+	TEST_RPR(  "strh	r",0, VAL1,", [r",1, 48,", -r",2, 24,"]")
+	TEST_RPR(  "streqh	r",14,VAL2,", [r",13,0, ", r",12, 48,"]")
+	TEST_RPR(  "strh	r",1, VAL1,", [r",2, 24,", r",3,  48,"]!")
+	TEST_RPR(  "strneh	r",12,VAL2,", [r",11,48,", -r",10,24,"]!")
+	TEST_RPR(  "strh	r",2, VAL1,", [r",3, 24,"], r",4, 48,"")
+	TEST_RPR(  "strh	r",10,VAL2,", [r",9, 48,"], -r",11,24,"")
+	TEST_UNSUPPORTED(".word 0xe1afc0ba	@ strh r12, [pc, r10]!")
+	TEST_UNSUPPORTED(".word 0xe089f0bb	@ strh pc, [r9], r11")
+	TEST_UNSUPPORTED(".word 0xe089a0bf	@ strh r10, [r9], pc")
+
+	TEST_PR(   "ldrh	r0, [r",0,  48,", -r",2, 24,"]")
+	TEST_PR(   "ldrcsh	r14, [r",13,0, ", r",12, 48,"]")
+	TEST_PR(   "ldrh	r1, [r",2,  24,", r",3,  48,"]!")
+	TEST_PR(   "ldrcch	r12, [r",11,48,", -r",10,24,"]!")
+	TEST_PR(   "ldrh	r2, [r",3,  24,"], r",4, 48,"")
+	TEST_PR(   "ldrh	r10, [r",9, 48,"], -r",11,24,"")
+	TEST_UNSUPPORTED(".word 0xe1bfc0ba	@ ldrh r12, [pc, r10]!")
+	TEST_UNSUPPORTED(".word 0xe099f0bb	@ ldrh pc, [r9], r11")
+	TEST_UNSUPPORTED(".word 0xe099a0bf	@ ldrh r10, [r9], pc")
+
+	TEST_RP(   "strh	r",0, VAL1,", [r",1, 24,", #-2]")
+	TEST_RP(   "strmih	r",14,VAL2,", [r",13,0, ", #2]")
+	TEST_RP(   "strh	r",1, VAL1,", [r",2, 24,", #4]!")
+	TEST_RP(   "strplh	r",12,VAL2,", [r",11,24,", #-4]!")
+	TEST_RP(   "strh	r",2, VAL1,", [r",3, 24,"], #48")
+	TEST_RP(   "strh	r",10,VAL2,", [r",9, 64,"], #-48")
+	TEST_UNSUPPORTED(".word 0xe1efc3b0	@ strh r12, [pc, #48]!")
+	TEST_UNSUPPORTED(".word 0xe0c9f3b0	@ strh pc, [r9], #48")
+
+	TEST_P(	   "ldrh	r0, [r",0,  24,", #-2]")
+	TEST_P(	   "ldrvsh	r14, [r",13,0, ", #2]")
+	TEST_P(	   "ldrh	r1, [r",2,  24,", #4]!")
+	TEST_P(	   "ldrvch	r12, [r",11,24,", #-4]!")
+	TEST_P(	   "ldrh	r2, [r",3,  24,"], #48")
+	TEST_P(	   "ldrh	r10, [r",9, 64,"], #-48")
+	TEST(      "ldrh	r0, [pc, #0]")
+	TEST_UNSUPPORTED(".word 0xe1ffc3b0	@ ldrh r12, [pc, #48]!")
+	TEST_UNSUPPORTED(".word 0xe0d9f3b0	@ ldrh pc, [r9], #48")
+
+	TEST_PR(   "ldrsb	r0, [r",0,  48,", -r",2, 24,"]")
+	TEST_PR(   "ldrhisb	r14, [r",13,0,", r",12,  48,"]")
+	TEST_PR(   "ldrsb	r1, [r",2,  24,", r",3,  48,"]!")
+	TEST_PR(   "ldrlssb	r12, [r",11,48,", -r",10,24,"]!")
+	TEST_PR(   "ldrsb	r2, [r",3,  24,"], r",4, 48,"")
+	TEST_PR(   "ldrsb	r10, [r",9, 48,"], -r",11,24,"")
+	TEST_UNSUPPORTED(".word 0xe1bfc0da	@ ldrsb r12, [pc, r10]!")
+	TEST_UNSUPPORTED(".word 0xe099f0db	@ ldrsb pc, [r9], r11")
+
+	TEST_P(	   "ldrsb	r0, [r",0,  24,", #-1]")
+	TEST_P(	   "ldrgesb	r14, [r",13,0, ", #1]")
+	TEST_P(	   "ldrsb	r1, [r",2,  24,", #4]!")
+	TEST_P(	   "ldrltsb	r12, [r",11,24,", #-4]!")
+	TEST_P(	   "ldrsb	r2, [r",3,  24,"], #48")
+	TEST_P(	   "ldrsb	r10, [r",9, 64,"], #-48")
+	TEST(      "ldrsb	r0, [pc, #0]")
+	TEST_UNSUPPORTED(".word 0xe1ffc3d0	@ ldrsb r12, [pc, #48]!")
+	TEST_UNSUPPORTED(".word 0xe0d9f3d0	@ ldrsb pc, [r9], #48")
+
+	TEST_PR(   "ldrsh	r0, [r",0,  48,", -r",2, 24,"]")
+	TEST_PR(   "ldrgtsh	r14, [r",13,0, ", r",12, 48,"]")
+	TEST_PR(   "ldrsh	r1, [r",2,  24,", r",3,  48,"]!")
+	TEST_PR(   "ldrlesh	r12, [r",11,48,", -r",10,24,"]!")
+	TEST_PR(   "ldrsh	r2, [r",3,  24,"], r",4, 48,"")
+	TEST_PR(   "ldrsh	r10, [r",9, 48,"], -r",11,24,"")
+	TEST_UNSUPPORTED(".word 0xe1bfc0fa	@ ldrsh r12, [pc, r10]!")
+	TEST_UNSUPPORTED(".word 0xe099f0fb	@ ldrsh pc, [r9], r11")
+
+	TEST_P(	   "ldrsh	r0, [r",0,  24,", #-1]")
+	TEST_P(	   "ldreqsh	r14, [r",13,0 ,", #1]")
+	TEST_P(	   "ldrsh	r1, [r",2,  24,", #4]!")
+	TEST_P(	   "ldrnesh	r12, [r",11,24,", #-4]!")
+	TEST_P(	   "ldrsh	r2, [r",3,  24,"], #48")
+	TEST_P(	   "ldrsh	r10, [r",9, 64,"], #-48")
+	TEST(      "ldrsh	r0, [pc, #0]")
+	TEST_UNSUPPORTED(".word 0xe1ffc3f0	@ ldrsh r12, [pc, #48]!")
+	TEST_UNSUPPORTED(".word 0xe0d9f3f0	@ ldrsh pc, [r9], #48")
+
+#if __LINUX_ARM_ARCH__ >= 7
+	TEST_UNSUPPORTED("strht	r1, [r2], r3")
+	TEST_UNSUPPORTED("ldrht	r1, [r2], r3")
+	TEST_UNSUPPORTED("strht	r1, [r2], #48")
+	TEST_UNSUPPORTED("ldrht	r1, [r2], #48")
+	TEST_UNSUPPORTED("ldrsbt	r1, [r2], r3")
+	TEST_UNSUPPORTED("ldrsbt	r1, [r2], #48")
+	TEST_UNSUPPORTED("ldrsht	r1, [r2], r3")
+	TEST_UNSUPPORTED("ldrsht	r1, [r2], #48")
+#endif
+
+	TEST_RPR(  "strd	r",0, VAL1,", [r",1, 48,", -r",2,24,"]")
+	TEST_RPR(  "strccd	r",8, VAL2,", [r",13,0, ", r",12,48,"]")
+	TEST_RPR(  "strd	r",4, VAL1,", [r",2, 24,", r",3, 48,"]!")
+	TEST_RPR(  "strcsd	r",12,VAL2,", [r",11,48,", -r",10,24,"]!")
+	TEST_RPR(  "strd	r",2, VAL1,", [r",3, 24,"], r",4,48,"")
+	TEST_RPR(  "strd	r",10,VAL2,", [r",9, 48,"], -r",7,24,"")
+	TEST_UNSUPPORTED(".word 0xe1afc0fa	@ strd r12, [pc, r10]!")
+
+	TEST_PR(   "ldrd	r0, [r",0, 48,", -r",2,24,"]")
+	TEST_PR(   "ldrmid	r8, [r",13,0, ", r",12,48,"]")
+	TEST_PR(   "ldrd	r4, [r",2, 24,", r",3, 48,"]!")
+	TEST_PR(   "ldrpld	r6, [r",11,48,", -r",10,24,"]!")
+	TEST_PR(   "ldrd	r2, [r",5, 24,"], r",4,48,"")
+	TEST_PR(   "ldrd	r10, [r",9,48,"], -r",7,24,"")
+	TEST_UNSUPPORTED(".word 0xe1afc0da	@ ldrd r12, [pc, r10]!")
+	TEST_UNSUPPORTED(".word 0xe089f0db	@ ldrd pc, [r9], r11")
+	TEST_UNSUPPORTED(".word 0xe089e0db	@ ldrd lr, [r9], r11")
+	TEST_UNSUPPORTED(".word 0xe089c0df	@ ldrd r12, [r9], pc")
+
+	TEST_RP(   "strd	r",0, VAL1,", [r",1, 24,", #-8]")
+	TEST_RP(   "strvsd	r",8, VAL2,", [r",13,0, ", #8]")
+	TEST_RP(   "strd	r",4, VAL1,", [r",2, 24,", #16]!")
+	TEST_RP(   "strvcd	r",12,VAL2,", [r",11,24,", #-16]!")
+	TEST_RP(   "strd	r",2, VAL1,", [r",4, 24,"], #48")
+	TEST_RP(   "strd	r",10,VAL2,", [r",9, 64,"], #-48")
+	TEST_UNSUPPORTED(".word 0xe1efc3f0	@ strd r12, [pc, #48]!")
+
+	TEST_P(	   "ldrd	r0, [r",0, 24,", #-8]")
+	TEST_P(	   "ldrhid	r8, [r",13,0, ", #8]")
+	TEST_P(	   "ldrd	r4, [r",2, 24,", #16]!")
+	TEST_P(	   "ldrlsd	r6, [r",11,24,", #-16]!")
+	TEST_P(	   "ldrd	r2, [r",5, 24,"], #48")
+	TEST_P(	   "ldrd	r10, [r",9,6,"], #-48")
+	TEST_UNSUPPORTED(".word 0xe1efc3d0	@ ldrd r12, [pc, #48]!")
+	TEST_UNSUPPORTED(".word 0xe0c9f3d0	@ ldrd pc, [r9], #48")
+	TEST_UNSUPPORTED(".word 0xe0c9e3d0	@ ldrd lr, [r9], #48")
+
+	TEST_GROUP("Miscellaneous")
+
+#if __LINUX_ARM_ARCH__ >= 7
+	TEST("movw	r0, #0")
+	TEST("movw	r0, #0xffff")
+	TEST("movw	lr, #0xffff")
+	TEST_UNSUPPORTED(".word 0xe300f000	@ movw pc, #0")
+	TEST_R("movt	r",0, VAL1,", #0")
+	TEST_R("movt	r",0, VAL2,", #0xffff")
+	TEST_R("movt	r",14,VAL1,", #0xffff")
+	TEST_UNSUPPORTED(".word 0xe340f000	@ movt pc, #0")
+#endif
+
+	TEST_UNSUPPORTED("msr	cpsr, 0x13")
+	TEST_UNSUPPORTED("msr	cpsr_f, 0xf0000000")
+	TEST_UNSUPPORTED("msr	spsr, 0x13")
+
+#if __LINUX_ARM_ARCH__ >= 7
+	TEST_SUPPORTED("yield")
+	TEST("sev")
+	TEST("nop")
+	TEST("wfi")
+	TEST_SUPPORTED("wfe")
+	TEST_UNSUPPORTED("dbg #0")
+#endif
+
+	TEST_GROUP("Load/store word and unsigned byte")
+
+#define LOAD_STORE(byte)							\
+	TEST_RP( "str"byte"	r",0, VAL1,", [r",1, 24,", #-2]")		\
+	TEST_RP( "str"byte"	r",14,VAL2,", [r",13,0, ", #2]")		\
+	TEST_RP( "str"byte"	r",1, VAL1,", [r",2, 24,", #4]!")		\
+	TEST_RP( "str"byte"	r",12,VAL2,", [r",11,24,", #-4]!")		\
+	TEST_RP( "str"byte"	r",2, VAL1,", [r",3, 24,"], #48")		\
+	TEST_RP( "str"byte"	r",10,VAL2,", [r",9, 64,"], #-48")		\
+	TEST_RPR("str"byte"	r",0, VAL1,", [r",1, 48,", -r",2, 24,"]")	\
+	TEST_RPR("str"byte"	r",14,VAL2,", [r",13,0, ", r",12, 48,"]")	\
+	TEST_RPR("str"byte"	r",1, VAL1,", [r",2, 24,", r",3,  48,"]!")	\
+	TEST_RPR("str"byte"	r",12,VAL2,", [r",11,48,", -r",10,24,"]!")	\
+	TEST_RPR("str"byte"	r",2, VAL1,", [r",3, 24,"], r",4, 48,"")	\
+	TEST_RPR("str"byte"	r",10,VAL2,", [r",9, 48,"], -r",11,24,"")	\
+	TEST_RPR("str"byte"	r",0, VAL1,", [r",1, 24,", r",2,  32,", asl #1]")\
+	TEST_RPR("str"byte"	r",14,VAL2,", [r",13,0, ", r",12, 32,", lsr #2]")\
+	TEST_RPR("str"byte"	r",1, VAL1,", [r",2, 24,", r",3,  32,", asr #3]!")\
+	TEST_RPR("str"byte"	r",12,VAL2,", [r",11,24,", r",10, 4,", ror #31]!")\
+	TEST_P(  "ldr"byte"	r0, [r",0,  24,", #-2]")			\
+	TEST_P(  "ldr"byte"	r14, [r",13,0, ", #2]")				\
+	TEST_P(  "ldr"byte"	r1, [r",2,  24,", #4]!")			\
+	TEST_P(  "ldr"byte"	r12, [r",11,24,", #-4]!")			\
+	TEST_P(  "ldr"byte"	r2, [r",3,  24,"], #48")			\
+	TEST_P(  "ldr"byte"	r10, [r",9, 64,"], #-48")			\
+	TEST_PR( "ldr"byte"	r0, [r",0,  48,", -r",2, 24,"]")		\
+	TEST_PR( "ldr"byte"	r14, [r",13,0, ", r",12, 48,"]")		\
+	TEST_PR( "ldr"byte"	r1, [r",2,  24,", r",3, 48,"]!")		\
+	TEST_PR( "ldr"byte"	r12, [r",11,48,", -r",10,24,"]!")		\
+	TEST_PR( "ldr"byte"	r2, [r",3,  24,"], r",4, 48,"")			\
+	TEST_PR( "ldr"byte"	r10, [r",9, 48,"], -r",11,24,"")		\
+	TEST_PR( "ldr"byte"	r0, [r",0,  24,", r",2,  32,", asl #1]")	\
+	TEST_PR( "ldr"byte"	r14, [r",13,0, ", r",12, 32,", lsr #2]")	\
+	TEST_PR( "ldr"byte"	r1, [r",2,  24,", r",3,  32,", asr #3]!")	\
+	TEST_PR( "ldr"byte"	r12, [r",11,24,", r",10, 4,", ror #31]!")	\
+	TEST(    "ldr"byte"	r0, [pc, #0]")					\
+	TEST_R(  "ldr"byte"	r12, [pc, r",14,0,"]")
+
+	LOAD_STORE("")
+	TEST_P(   "str	pc, [r",0,0,", #15*4]")
+	TEST_R(   "str	pc, [sp, r",2,15*4,"]")
+	TEST_BF(  "ldr	pc, [sp, #15*4]")
+	TEST_BF_R("ldr	pc, [sp, r",2,15*4,"]")
+
+	TEST_P(   "str	sp, [r",0,0,", #13*4]")
+	TEST_R(   "str	sp, [sp, r",2,13*4,"]")
+	TEST_BF(  "ldr	sp, [sp, #13*4]")
+	TEST_BF_R("ldr	sp, [sp, r",2,13*4,"]")
+
+#ifdef CONFIG_THUMB2_KERNEL
+	TEST_ARM_TO_THUMB_INTERWORK_P("ldr	pc, [r",0,0,", #15*4]")
+#endif
+	TEST_UNSUPPORTED(".word 0xe5af6008	@ str r6, [pc, #8]!")
+	TEST_UNSUPPORTED(".word 0xe7af6008	@ str r6, [pc, r8]!")
+	TEST_UNSUPPORTED(".word 0xe5bf6008	@ ldr r6, [pc, #8]!")
+	TEST_UNSUPPORTED(".word 0xe7bf6008	@ ldr r6, [pc, r8]!")
+	TEST_UNSUPPORTED(".word 0xe788600f	@ str r6, [r8, pc]")
+	TEST_UNSUPPORTED(".word 0xe798600f	@ ldr r6, [r8, pc]")
+
+	LOAD_STORE("b")
+	TEST_UNSUPPORTED(".word 0xe5f7f008	@ ldrb pc, [r7, #8]!")
+	TEST_UNSUPPORTED(".word 0xe7f7f008	@ ldrb pc, [r7, r8]!")
+	TEST_UNSUPPORTED(".word 0xe5ef6008	@ strb r6, [pc, #8]!")
+	TEST_UNSUPPORTED(".word 0xe7ef6008	@ strb r6, [pc, r3]!")
+	TEST_UNSUPPORTED(".word 0xe5ff6008	@ ldrb r6, [pc, #8]!")
+	TEST_UNSUPPORTED(".word 0xe7ff6008	@ ldrb r6, [pc, r3]!")
+
+	TEST_UNSUPPORTED("ldrt	r0, [r1], #4")
+	TEST_UNSUPPORTED("ldrt	r1, [r2], r3")
+	TEST_UNSUPPORTED("strt	r2, [r3], #4")
+	TEST_UNSUPPORTED("strt	r3, [r4], r5")
+	TEST_UNSUPPORTED("ldrbt	r4, [r5], #4")
+	TEST_UNSUPPORTED("ldrbt	r5, [r6], r7")
+	TEST_UNSUPPORTED("strbt	r6, [r7], #4")
+	TEST_UNSUPPORTED("strbt	r7, [r8], r9")
+
+#if __LINUX_ARM_ARCH__ >= 7
+	TEST_GROUP("Parallel addition and subtraction, signed")
+
+	TEST_UNSUPPORTED(".word 0xe6000010") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe60fffff") /* Unallocated space */
+
+	TEST_RR(    "sadd16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "sadd16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe61cff1a	@ sadd16	pc, r12, r10")
+	TEST_RR(    "sasx	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "sasx	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe61cff3a	@ sasx	pc, r12, r10")
+	TEST_RR(    "ssax	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "ssax	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe61cff5a	@ ssax	pc, r12, r10")
+	TEST_RR(    "ssub16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "ssub16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe61cff7a	@ ssub16	pc, r12, r10")
+	TEST_RR(    "sadd8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "sadd8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe61cff9a	@ sadd8	pc, r12, r10")
+	TEST_UNSUPPORTED(".word 0xe61000b0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe61fffbf") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe61000d0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe61fffdf") /* Unallocated space */
+	TEST_RR(    "ssub8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "ssub8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe61cfffa	@ ssub8	pc, r12, r10")
+
+	TEST_RR(    "qadd16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "qadd16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe62cff1a	@ qadd16	pc, r12, r10")
+	TEST_RR(    "qasx	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "qasx	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe62cff3a	@ qasx	pc, r12, r10")
+	TEST_RR(    "qsax	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "qsax	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe62cff5a	@ qsax	pc, r12, r10")
+	TEST_RR(    "qsub16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "qsub16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe62cff7a	@ qsub16	pc, r12, r10")
+	TEST_RR(    "qadd8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "qadd8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe62cff9a	@ qadd8	pc, r12, r10")
+	TEST_UNSUPPORTED(".word 0xe62000b0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe62fffbf") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe62000d0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe62fffdf") /* Unallocated space */
+	TEST_RR(    "qsub8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "qsub8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe62cfffa	@ qsub8	pc, r12, r10")
+
+	TEST_RR(    "shadd16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "shadd16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe63cff1a	@ shadd16	pc, r12, r10")
+	TEST_RR(    "shasx	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "shasx	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe63cff3a	@ shasx	pc, r12, r10")
+	TEST_RR(    "shsax	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "shsax	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe63cff5a	@ shsax	pc, r12, r10")
+	TEST_RR(    "shsub16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "shsub16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe63cff7a	@ shsub16	pc, r12, r10")
+	TEST_RR(    "shadd8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "shadd8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe63cff9a	@ shadd8	pc, r12, r10")
+	TEST_UNSUPPORTED(".word 0xe63000b0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe63fffbf") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe63000d0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe63fffdf") /* Unallocated space */
+	TEST_RR(    "shsub8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "shsub8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe63cfffa	@ shsub8	pc, r12, r10")
+
+	TEST_GROUP("Parallel addition and subtraction, unsigned")
+
+	TEST_UNSUPPORTED(".word 0xe6400010") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe64fffff") /* Unallocated space */
+
+	TEST_RR(    "uadd16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uadd16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe65cff1a	@ uadd16	pc, r12, r10")
+	TEST_RR(    "uasx	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uasx	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe65cff3a	@ uasx	pc, r12, r10")
+	TEST_RR(    "usax	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "usax	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe65cff5a	@ usax	pc, r12, r10")
+	TEST_RR(    "usub16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "usub16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe65cff7a	@ usub16	pc, r12, r10")
+	TEST_RR(    "uadd8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uadd8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe65cff9a	@ uadd8	pc, r12, r10")
+	TEST_UNSUPPORTED(".word 0xe65000b0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe65fffbf") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe65000d0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe65fffdf") /* Unallocated space */
+	TEST_RR(    "usub8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "usub8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe65cfffa	@ usub8	pc, r12, r10")
+
+	TEST_RR(    "uqadd16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uqadd16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe66cff1a	@ uqadd16	pc, r12, r10")
+	TEST_RR(    "uqasx	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uqasx	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe66cff3a	@ uqasx	pc, r12, r10")
+	TEST_RR(    "uqsax	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uqsax	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe66cff5a	@ uqsax	pc, r12, r10")
+	TEST_RR(    "uqsub16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uqsub16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe66cff7a	@ uqsub16	pc, r12, r10")
+	TEST_RR(    "uqadd8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uqadd8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe66cff9a	@ uqadd8	pc, r12, r10")
+	TEST_UNSUPPORTED(".word 0xe66000b0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe66fffbf") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe66000d0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe66fffdf") /* Unallocated space */
+	TEST_RR(    "uqsub8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uqsub8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe66cfffa	@ uqsub8	pc, r12, r10")
+
+	TEST_RR(    "uhadd16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uhadd16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe67cff1a	@ uhadd16	pc, r12, r10")
+	TEST_RR(    "uhasx	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uhasx	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe67cff3a	@ uhasx	pc, r12, r10")
+	TEST_RR(    "uhsax	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uhsax	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe67cff5a	@ uhsax	pc, r12, r10")
+	TEST_RR(    "uhsub16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uhsub16	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe67cff7a	@ uhsub16	pc, r12, r10")
+	TEST_RR(    "uhadd8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uhadd8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe67cff9a	@ uhadd8	pc, r12, r10")
+	TEST_UNSUPPORTED(".word 0xe67000b0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe67fffbf") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe67000d0") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe67fffdf") /* Unallocated space */
+	TEST_RR(    "uhsub8	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uhsub8	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe67cfffa	@ uhsub8	pc, r12, r10")
+	TEST_UNSUPPORTED(".word 0xe67feffa	@ uhsub8	r14, pc, r10")
+	TEST_UNSUPPORTED(".word 0xe67cefff	@ uhsub8	r14, r12, pc")
+#endif /* __LINUX_ARM_ARCH__ >= 7 */
+
+#if __LINUX_ARM_ARCH__ >= 6
+	TEST_GROUP("Packing, unpacking, saturation, and reversal")
+
+	TEST_RR(    "pkhbt	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "pkhbt	r14,r",12, HH1,", r",10,HH2,", lsl #2")
+	TEST_UNSUPPORTED(".word 0xe68cf11a	@ pkhbt	pc, r12, r10, lsl #2")
+	TEST_RR(    "pkhtb	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "pkhtb	r14,r",12, HH1,", r",10,HH2,", asr #2")
+	TEST_UNSUPPORTED(".word 0xe68cf15a	@ pkhtb	pc, r12, r10, asr #2")
+	TEST_UNSUPPORTED(".word 0xe68fe15a	@ pkhtb	r14, pc, r10, asr #2")
+	TEST_UNSUPPORTED(".word 0xe68ce15f	@ pkhtb	r14, r12, pc, asr #2")
+	TEST_UNSUPPORTED(".word 0xe6900010") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe69fffdf") /* Unallocated space */
+
+	TEST_R(     "ssat	r0, #24, r",0,   VAL1,"")
+	TEST_R(     "ssat	r14, #24, r",12, VAL2,"")
+	TEST_R(     "ssat	r0, #24, r",0,   VAL1,", lsl #8")
+	TEST_R(     "ssat	r14, #24, r",12, VAL2,", asr #8")
+	TEST_UNSUPPORTED(".word 0xe6b7f01c	@ ssat	pc, #24, r12")
+
+	TEST_R(     "usat	r0, #24, r",0,   VAL1,"")
+	TEST_R(     "usat	r14, #24, r",12, VAL2,"")
+	TEST_R(     "usat	r0, #24, r",0,   VAL1,", lsl #8")
+	TEST_R(     "usat	r14, #24, r",12, VAL2,", asr #8")
+	TEST_UNSUPPORTED(".word 0xe6f7f01c	@ usat	pc, #24, r12")
+
+	TEST_RR(    "sxtab16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "sxtab16	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "sxtb16	r8, r",7,  HH1,"")
+	TEST_UNSUPPORTED(".word 0xe68cf47a	@ sxtab16	pc,r12, r10, ror #8")
+
+	TEST_RR(    "sel	r0, r",0,  VAL1,", r",1, VAL2,"")
+	TEST_RR(    "sel	r14, r",12,VAL1,", r",10, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe68cffba	@ sel	pc, r12, r10")
+	TEST_UNSUPPORTED(".word 0xe68fefba	@ sel	r14, pc, r10")
+	TEST_UNSUPPORTED(".word 0xe68cefbf	@ sel	r14, r12, pc")
+
+	TEST_R(     "ssat16	r0, #12, r",0,   HH1,"")
+	TEST_R(     "ssat16	r14, #12, r",12, HH2,"")
+	TEST_UNSUPPORTED(".word 0xe6abff3c	@ ssat16	pc, #12, r12")
+
+	TEST_RR(    "sxtab	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "sxtab	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "sxtb	r8, r",7,  HH1,"")
+	TEST_UNSUPPORTED(".word 0xe6acf47a	@ sxtab	pc,r12, r10, ror #8")
+
+	TEST_R(     "rev	r0, r",0,   VAL1,"")
+	TEST_R(     "rev	r14, r",12, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe6bfff3c	@ rev	pc, r12")
+
+	TEST_RR(    "sxtah	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "sxtah	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "sxth	r8, r",7,  HH1,"")
+	TEST_UNSUPPORTED(".word 0xe6bcf47a	@ sxtah	pc,r12, r10, ror #8")
+
+	TEST_R(     "rev16	r0, r",0,   VAL1,"")
+	TEST_R(     "rev16	r14, r",12, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe6bfffbc	@ rev16	pc, r12")
+
+	TEST_RR(    "uxtab16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uxtab16	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "uxtb16	r8, r",7,  HH1,"")
+	TEST_UNSUPPORTED(".word 0xe6ccf47a	@ uxtab16	pc,r12, r10, ror #8")
+
+	TEST_R(     "usat16	r0, #12, r",0,   HH1,"")
+	TEST_R(     "usat16	r14, #12, r",12, HH2,"")
+	TEST_UNSUPPORTED(".word 0xe6ecff3c	@ usat16	pc, #12, r12")
+	TEST_UNSUPPORTED(".word 0xe6ecef3f	@ usat16	r14, #12, pc")
+
+	TEST_RR(    "uxtab	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uxtab	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "uxtb	r8, r",7,  HH1,"")
+	TEST_UNSUPPORTED(".word 0xe6ecf47a	@ uxtab	pc,r12, r10, ror #8")
+
+#if __LINUX_ARM_ARCH__ >= 7
+	TEST_R(     "rbit	r0, r",0,   VAL1,"")
+	TEST_R(     "rbit	r14, r",12, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe6ffff3c	@ rbit	pc, r12")
+#endif
+
+	TEST_RR(    "uxtah	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uxtah	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "uxth	r8, r",7,  HH1,"")
+	TEST_UNSUPPORTED(".word 0xe6fff077	@ uxth	pc, r7")
+	TEST_UNSUPPORTED(".word 0xe6ff807f	@ uxth	r8, pc")
+	TEST_UNSUPPORTED(".word 0xe6fcf47a	@ uxtah	pc, r12, r10, ror #8")
+	TEST_UNSUPPORTED(".word 0xe6fce47f	@ uxtah	r14, r12, pc, ror #8")
+
+	TEST_R(     "revsh	r0, r",0,   VAL1,"")
+	TEST_R(     "revsh	r14, r",12, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe6ffff3c	@ revsh	pc, r12")
+	TEST_UNSUPPORTED(".word 0xe6ffef3f	@ revsh	r14, pc")
+
+	TEST_UNSUPPORTED(".word 0xe6900070") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe69fff7f") /* Unallocated space */
+
+	TEST_UNSUPPORTED(".word 0xe6d00070") /* Unallocated space */
+	TEST_UNSUPPORTED(".word 0xe6dfff7f") /* Unallocated space */
+#endif /* __LINUX_ARM_ARCH__ >= 6 */
+
+#if __LINUX_ARM_ARCH__ >= 6
+	TEST_GROUP("Signed multiplies")
+
+	TEST_RRR(   "smlad	r0, r",0,  HH1,", r",1, HH2,", r",2, VAL1,"")
+	TEST_RRR(   "smlad	r14, r",12,HH2,", r",10,HH1,", r",8, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe70f8a1c	@ smlad	pc, r12, r10, r8")
+	TEST_RRR(   "smladx	r0, r",0,  HH1,", r",1, HH2,", r",2, VAL1,"")
+	TEST_RRR(   "smladx	r14, r",12,HH2,", r",10,HH1,", r",8, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe70f8a3c	@ smladx	pc, r12, r10, r8")
+
+	TEST_RR(   "smuad	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(   "smuad	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe70ffa1c	@ smuad	pc, r12, r10")
+	TEST_RR(   "smuadx	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(   "smuadx	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe70ffa3c	@ smuadx	pc, r12, r10")
+
+	TEST_RRR(   "smlsd	r0, r",0,  HH1,", r",1, HH2,", r",2, VAL1,"")
+	TEST_RRR(   "smlsd	r14, r",12,HH2,", r",10,HH1,", r",8, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe70f8a5c	@ smlsd	pc, r12, r10, r8")
+	TEST_RRR(   "smlsdx	r0, r",0,  HH1,", r",1, HH2,", r",2, VAL1,"")
+	TEST_RRR(   "smlsdx	r14, r",12,HH2,", r",10,HH1,", r",8, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe70f8a7c	@ smlsdx	pc, r12, r10, r8")
+
+	TEST_RR(   "smusd	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(   "smusd	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe70ffa5c	@ smusd	pc, r12, r10")
+	TEST_RR(   "smusdx	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(   "smusdx	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_UNSUPPORTED(".word 0xe70ffa7c	@ smusdx	pc, r12, r10")
+
+	TEST_RRRR( "smlald	r",0, VAL1,", r",1, VAL2, ", r",0, HH1,", r",1, HH2)
+	TEST_RRRR( "smlald	r",11,VAL2,", r",10,VAL1, ", r",9, HH2,", r",8, HH1)
+	TEST_UNSUPPORTED(".word 0xe74af819	@ smlald	pc, r10, r9, r8")
+	TEST_UNSUPPORTED(".word 0xe74fb819	@ smlald	r11, pc, r9, r8")
+	TEST_UNSUPPORTED(".word 0xe74ab81f	@ smlald	r11, r10, pc, r8")
+	TEST_UNSUPPORTED(".word 0xe74abf19	@ smlald	r11, r10, r9, pc")
+
+	TEST_RRRR( "smlaldx	r",0, VAL1,", r",1, VAL2, ", r",0, HH1,", r",1, HH2)
+	TEST_RRRR( "smlaldx	r",11,VAL2,", r",10,VAL1, ", r",9, HH2,", r",8, HH1)
+	TEST_UNSUPPORTED(".word 0xe74af839	@ smlaldx	pc, r10, r9, r8")
+	TEST_UNSUPPORTED(".word 0xe74fb839	@ smlaldx	r11, pc, r9, r8")
+
+	TEST_RRR(  "smmla	r0, r",0,  VAL1,", r",1, VAL2,", r",2, VAL1,"")
+	TEST_RRR(  "smmla	r14, r",12,VAL2,", r",10,VAL1,", r",8, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe75f8a1c	@ smmla	pc, r12, r10, r8")
+	TEST_RRR(  "smmlar	r0, r",0,  VAL1,", r",1, VAL2,", r",2, VAL1,"")
+	TEST_RRR(  "smmlar	r14, r",12,VAL2,", r",10,VAL1,", r",8, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe75f8a3c	@ smmlar	pc, r12, r10, r8")
+
+	TEST_RR(   "smmul	r0, r",0,  VAL1,", r",1, VAL2,"")
+	TEST_RR(   "smmul	r14, r",12,VAL2,", r",10,VAL1,"")
+	TEST_UNSUPPORTED(".word 0xe75ffa1c	@ smmul	pc, r12, r10")
+	TEST_RR(   "smmulr	r0, r",0,  VAL1,", r",1, VAL2,"")
+	TEST_RR(   "smmulr	r14, r",12,VAL2,", r",10,VAL1,"")
+	TEST_UNSUPPORTED(".word 0xe75ffa3c	@ smmulr	pc, r12, r10")
+
+	TEST_RRR(  "smmls	r0, r",0,  VAL1,", r",1, VAL2,", r",2, VAL1,"")
+	TEST_RRR(  "smmls	r14, r",12,VAL2,", r",10,VAL1,", r",8, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe75f8adc	@ smmls	pc, r12, r10, r8")
+	TEST_RRR(  "smmlsr	r0, r",0,  VAL1,", r",1, VAL2,", r",2, VAL1,"")
+	TEST_RRR(  "smmlsr	r14, r",12,VAL2,", r",10,VAL1,", r",8, VAL2,"")
+	TEST_UNSUPPORTED(".word 0xe75f8afc	@ smmlsr	pc, r12, r10, r8")
+	TEST_UNSUPPORTED(".word 0xe75e8aff	@ smmlsr	r14, pc, r10, r8")
+	TEST_UNSUPPORTED(".word 0xe75e8ffc	@ smmlsr	r14, r12, pc, r8")
+	TEST_UNSUPPORTED(".word 0xe75efafc	@ smmlsr	r14, r12, r10, pc")
+
+	TEST_RR(   "usad8	r0, r",0,  VAL1,", r",1, VAL2,"")
+	TEST_RR(   "usad8	r14, r",12,VAL2,", r",10,VAL1,"")
+	TEST_UNSUPPORTED(".word 0xe75ffa1c	@ usad8	pc, r12, r10")
+	TEST_UNSUPPORTED(".word 0xe75efa1f	@ usad8	r14, pc, r10")
+	TEST_UNSUPPORTED(".word 0xe75eff1c	@ usad8	r14, r12, pc")
+
+	TEST_RRR(  "usada8	r0, r",0,  VAL1,", r",1, VAL2,", r",2, VAL3,"")
+	TEST_RRR(  "usada8	r14, r",12,VAL2,", r",10,VAL1,", r",8, VAL3,"")
+	TEST_UNSUPPORTED(".word 0xe78f8a1c	@ usada8	pc, r12, r10, r8")
+	TEST_UNSUPPORTED(".word 0xe78e8a1f	@ usada8	r14, pc, r10, r8")
+	TEST_UNSUPPORTED(".word 0xe78e8f1c	@ usada8	r14, r12, pc, r8")
+#endif /* __LINUX_ARM_ARCH__ >= 6 */
+
+#if __LINUX_ARM_ARCH__ >= 7
+	TEST_GROUP("Bit Field")
+
+	TEST_R(     "sbfx	r0, r",0  , VAL1,", #0, #31")
+	TEST_R(     "sbfxeq	r14, r",12, VAL2,", #8, #16")
+	TEST_R(     "sbfx	r4, r",10,  VAL1,", #16, #15")
+	TEST_UNSUPPORTED(".word 0xe7aff45c	@ sbfx	pc, r12, #8, #16")
+
+	TEST_R(     "ubfx	r0, r",0  , VAL1,", #0, #31")
+	TEST_R(     "ubfxcs	r14, r",12, VAL2,", #8, #16")
+	TEST_R(     "ubfx	r4, r",10,  VAL1,", #16, #15")
+	TEST_UNSUPPORTED(".word 0xe7eff45c	@ ubfx	pc, r12, #8, #16")
+	TEST_UNSUPPORTED(".word 0xe7efc45f	@ ubfx	r12, pc, #8, #16")
+
+	TEST_R(     "bfc	r",0, VAL1,", #4, #20")
+	TEST_R(     "bfcvs	r",14,VAL2,", #4, #20")
+	TEST_R(     "bfc	r",7, VAL1,", #0, #31")
+	TEST_R(     "bfc	r",8, VAL2,", #0, #31")
+	TEST_UNSUPPORTED(".word 0xe7def01f	@ bfc	pc, #0, #31");
+
+	TEST_RR(    "bfi	r",0, VAL1,", r",0  , VAL2,", #0, #31")
+	TEST_RR(    "bfipl	r",12,VAL1,", r",14 , VAL2,", #4, #20")
+	TEST_UNSUPPORTED(".word 0xe7d7f21e	@ bfi	pc, r14, #4, #20")
+
+	TEST_UNSUPPORTED(".word 0x07f000f0")  /* Permanently UNDEFINED */
+	TEST_UNSUPPORTED(".word 0x07ffffff")  /* Permanently UNDEFINED */
+#endif /* __LINUX_ARM_ARCH__ >= 6 */
+
+	TEST_GROUP("Branch, branch with link, and block data transfer")
+
+	TEST_P(   "stmda	r",0, 16*4,", {r0}")
+	TEST_P(   "stmeqda	r",4, 16*4,", {r0-r15}")
+	TEST_P(   "stmneda	r",8, 16*4,"!, {r8-r15}")
+	TEST_P(   "stmda	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+	TEST_P(   "stmda	r",13,0,   "!, {pc}")
+
+	TEST_P(   "ldmda	r",0, 16*4,", {r0}")
+	TEST_BF_P("ldmcsda	r",4, 15*4,", {r0-r15}")
+	TEST_BF_P("ldmccda	r",7, 15*4,"!, {r8-r15}")
+	TEST_P(   "ldmda	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+	TEST_BF_P("ldmda	r",14,15*4,"!, {pc}")
+
+	TEST_P(   "stmia	r",0, 16*4,", {r0}")
+	TEST_P(   "stmmiia	r",4, 16*4,", {r0-r15}")
+	TEST_P(   "stmplia	r",8, 16*4,"!, {r8-r15}")
+	TEST_P(   "stmia	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+	TEST_P(   "stmia	r",14,0,   "!, {pc}")
+
+	TEST_P(   "ldmia	r",0, 16*4,", {r0}")
+	TEST_BF_P("ldmvsia	r",4, 0,   ", {r0-r15}")
+	TEST_BF_P("ldmvcia	r",7, 8*4, "!, {r8-r15}")
+	TEST_P(   "ldmia	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+	TEST_BF_P("ldmia	r",14,15*4,"!, {pc}")
+
+	TEST_P(   "stmdb	r",0, 16*4,", {r0}")
+	TEST_P(   "stmhidb	r",4, 16*4,", {r0-r15}")
+	TEST_P(   "stmlsdb	r",8, 16*4,"!, {r8-r15}")
+	TEST_P(   "stmdb	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+	TEST_P(   "stmdb	r",13,4,   "!, {pc}")
+
+	TEST_P(   "ldmdb	r",0, 16*4,", {r0}")
+	TEST_BF_P("ldmgedb	r",4, 16*4,", {r0-r15}")
+	TEST_BF_P("ldmltdb	r",7, 16*4,"!, {r8-r15}")
+	TEST_P(   "ldmdb	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+	TEST_BF_P("ldmdb	r",14,16*4,"!, {pc}")
+
+	TEST_P(   "stmib	r",0, 16*4,", {r0}")
+	TEST_P(   "stmgtib	r",4, 16*4,", {r0-r15}")
+	TEST_P(   "stmleib	r",8, 16*4,"!, {r8-r15}")
+	TEST_P(   "stmib	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+	TEST_P(   "stmib	r",13,-4,  "!, {pc}")
+
+	TEST_P(   "ldmib	r",0, 16*4,", {r0}")
+	TEST_BF_P("ldmeqib	r",4, -4,", {r0-r15}")
+	TEST_BF_P("ldmneib	r",7, 7*4,"!, {r8-r15}")
+	TEST_P(   "ldmib	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+	TEST_BF_P("ldmib	r",14,14*4,"!, {pc}")
+
+	TEST_P(   "stmdb	r",13,16*4,"!, {r3-r12,lr}")
+	TEST_P(	  "stmeqdb	r",13,16*4,"!, {r3-r12}")
+	TEST_P(   "stmnedb	r",2, 16*4,", {r3-r12,lr}")
+	TEST_P(   "stmdb	r",13,16*4,"!, {r2-r12,lr}")
+	TEST_P(   "stmdb	r",0, 16*4,", {r0-r12}")
+	TEST_P(   "stmdb	r",0, 16*4,", {r0-r12,lr}")
+
+	TEST_BF_P("ldmia	r",13,5*4, "!, {r3-r12,pc}")
+	TEST_P(	  "ldmccia	r",13,5*4, "!, {r3-r12}")
+	TEST_BF_P("ldmcsia	r",2, 5*4, "!, {r3-r12,pc}")
+	TEST_BF_P("ldmia	r",13,4*4, "!, {r2-r12,pc}")
+	TEST_P(   "ldmia	r",0, 16*4,", {r0-r12}")
+	TEST_P(   "ldmia	r",0, 16*4,", {r0-r12,lr}")
+
+#ifdef CONFIG_THUMB2_KERNEL
+	TEST_ARM_TO_THUMB_INTERWORK_P("ldmplia	r",0,15*4,", {pc}")
+	TEST_ARM_TO_THUMB_INTERWORK_P("ldmmiia	r",13,0,", {r0-r15}")
+#endif
+	TEST_BF("b	2f")
+	TEST_BF("bl	2f")
+	TEST_BB("b	2b")
+	TEST_BB("bl	2b")
+
+	TEST_BF("beq	2f")
+	TEST_BF("bleq	2f")
+	TEST_BB("bne	2b")
+	TEST_BB("blne	2b")
+
+	TEST_BF("bgt	2f")
+	TEST_BF("blgt	2f")
+	TEST_BB("blt	2b")
+	TEST_BB("bllt	2b")
+
+	TEST_GROUP("Supervisor Call, and coprocessor instructions")
+
+	/*
+	 * We can't really test these by executing them, so all
+	 * we can do is check that probes are, or are not allowed.
+	 * At the moment none are allowed...
+	 */
+#define TEST_COPROCESSOR(code) TEST_UNSUPPORTED(code)
+
+#define COPROCESSOR_INSTRUCTIONS_ST_LD(two,cc)					\
+	TEST_COPROCESSOR("stc"two"	0, cr0, [r13, #4]")			\
+	TEST_COPROCESSOR("stc"two"	0, cr0, [r13, #-4]")			\
+	TEST_COPROCESSOR("stc"two"	0, cr0, [r13, #4]!")			\
+	TEST_COPROCESSOR("stc"two"	0, cr0, [r13, #-4]!")			\
+	TEST_COPROCESSOR("stc"two"	0, cr0, [r13], #4")			\
+	TEST_COPROCESSOR("stc"two"	0, cr0, [r13], #-4")			\
+	TEST_COPROCESSOR("stc"two"	0, cr0, [r13], {1}")			\
+	TEST_COPROCESSOR("stc"two"l	0, cr0, [r13, #4]")			\
+	TEST_COPROCESSOR("stc"two"l	0, cr0, [r13, #-4]")			\
+	TEST_COPROCESSOR("stc"two"l	0, cr0, [r13, #4]!")			\
+	TEST_COPROCESSOR("stc"two"l	0, cr0, [r13, #-4]!")			\
+	TEST_COPROCESSOR("stc"two"l	0, cr0, [r13], #4")			\
+	TEST_COPROCESSOR("stc"two"l	0, cr0, [r13], #-4")			\
+	TEST_COPROCESSOR("stc"two"l	0, cr0, [r13], {1}")			\
+	TEST_COPROCESSOR("ldc"two"	0, cr0, [r13, #4]")			\
+	TEST_COPROCESSOR("ldc"two"	0, cr0, [r13, #-4]")			\
+	TEST_COPROCESSOR("ldc"two"	0, cr0, [r13, #4]!")			\
+	TEST_COPROCESSOR("ldc"two"	0, cr0, [r13, #-4]!")			\
+	TEST_COPROCESSOR("ldc"two"	0, cr0, [r13], #4")			\
+	TEST_COPROCESSOR("ldc"two"	0, cr0, [r13], #-4")			\
+	TEST_COPROCESSOR("ldc"two"	0, cr0, [r13], {1}")			\
+	TEST_COPROCESSOR("ldc"two"l	0, cr0, [r13, #4]")			\
+	TEST_COPROCESSOR("ldc"two"l	0, cr0, [r13, #-4]")			\
+	TEST_COPROCESSOR("ldc"two"l	0, cr0, [r13, #4]!")			\
+	TEST_COPROCESSOR("ldc"two"l	0, cr0, [r13, #-4]!")			\
+	TEST_COPROCESSOR("ldc"two"l	0, cr0, [r13], #4")			\
+	TEST_COPROCESSOR("ldc"two"l	0, cr0, [r13], #-4")			\
+	TEST_COPROCESSOR("ldc"two"l	0, cr0, [r13], {1}")			\
+										\
+	TEST_COPROCESSOR( "stc"two"	0, cr0, [r15, #4]")			\
+	TEST_COPROCESSOR( "stc"two"	0, cr0, [r15, #-4]")			\
+	TEST_UNSUPPORTED(".word 0x"cc"daf0001	@ stc"two"	0, cr0, [r15, #4]!")	\
+	TEST_UNSUPPORTED(".word 0x"cc"d2f0001	@ stc"two"	0, cr0, [r15, #-4]!")	\
+	TEST_UNSUPPORTED(".word 0x"cc"caf0001	@ stc"two"	0, cr0, [r15], #4")	\
+	TEST_UNSUPPORTED(".word 0x"cc"c2f0001	@ stc"two"	0, cr0, [r15], #-4")	\
+	TEST_COPROCESSOR( "stc"two"	0, cr0, [r15], {1}")			\
+	TEST_COPROCESSOR( "stc"two"l	0, cr0, [r15, #4]")			\
+	TEST_COPROCESSOR( "stc"two"l	0, cr0, [r15, #-4]")			\
+	TEST_UNSUPPORTED(".word 0x"cc"def0001	@ stc"two"l	0, cr0, [r15, #4]!")	\
+	TEST_UNSUPPORTED(".word 0x"cc"d6f0001	@ stc"two"l	0, cr0, [r15, #-4]!")	\
+	TEST_UNSUPPORTED(".word 0x"cc"cef0001	@ stc"two"l	0, cr0, [r15], #4")	\
+	TEST_UNSUPPORTED(".word 0x"cc"c6f0001	@ stc"two"l	0, cr0, [r15], #-4")	\
+	TEST_COPROCESSOR( "stc"two"l	0, cr0, [r15], {1}")			\
+	TEST_COPROCESSOR( "ldc"two"	0, cr0, [r15, #4]")			\
+	TEST_COPROCESSOR( "ldc"two"	0, cr0, [r15, #-4]")			\
+	TEST_UNSUPPORTED(".word 0x"cc"dbf0001	@ ldc"two"	0, cr0, [r15, #4]!")	\
+	TEST_UNSUPPORTED(".word 0x"cc"d3f0001	@ ldc"two"	0, cr0, [r15, #-4]!")	\
+	TEST_UNSUPPORTED(".word 0x"cc"cbf0001	@ ldc"two"	0, cr0, [r15], #4")	\
+	TEST_UNSUPPORTED(".word 0x"cc"c3f0001	@ ldc"two"	0, cr0, [r15], #-4")	\
+	TEST_COPROCESSOR( "ldc"two"	0, cr0, [r15], {1}")			\
+	TEST_COPROCESSOR( "ldc"two"l	0, cr0, [r15, #4]")			\
+	TEST_COPROCESSOR( "ldc"two"l	0, cr0, [r15, #-4]")			\
+	TEST_UNSUPPORTED(".word 0x"cc"dff0001	@ ldc"two"l	0, cr0, [r15, #4]!")	\
+	TEST_UNSUPPORTED(".word 0x"cc"d7f0001	@ ldc"two"l	0, cr0, [r15, #-4]!")	\
+	TEST_UNSUPPORTED(".word 0x"cc"cff0001	@ ldc"two"l	0, cr0, [r15], #4")	\
+	TEST_UNSUPPORTED(".word 0x"cc"c7f0001	@ ldc"two"l	0, cr0, [r15], #-4")	\
+	TEST_COPROCESSOR( "ldc"two"l	0, cr0, [r15], {1}")
+
+#define COPROCESSOR_INSTRUCTIONS_MC_MR(two,cc)					\
+										\
+	TEST_COPROCESSOR( "mcrr"two"	0, 15, r0, r14, cr0")			\
+	TEST_COPROCESSOR( "mcrr"two"	15, 0, r14, r0, cr15")			\
+	TEST_UNSUPPORTED(".word 0x"cc"c4f00f0	@ mcrr"two"	0, 15, r0, r15, cr0")	\
+	TEST_UNSUPPORTED(".word 0x"cc"c40ff0f	@ mcrr"two"	15, 0, r15, r0, cr15")	\
+	TEST_COPROCESSOR( "mrrc"two"	0, 15, r0, r14, cr0")			\
+	TEST_COPROCESSOR( "mrrc"two"	15, 0, r14, r0, cr15")			\
+	TEST_UNSUPPORTED(".word 0x"cc"c5f00f0	@ mrrc"two"	0, 15, r0, r15, cr0")	\
+	TEST_UNSUPPORTED(".word 0x"cc"c50ff0f	@ mrrc"two"	15, 0, r15, r0, cr15")	\
+	TEST_COPROCESSOR( "cdp"two"	15, 15, cr15, cr15, cr15, 7")		\
+	TEST_COPROCESSOR( "cdp"two"	0, 0, cr0, cr0, cr0, 0")		\
+	TEST_COPROCESSOR( "mcr"two"	15, 7, r15, cr15, cr15, 7")		\
+	TEST_COPROCESSOR( "mcr"two"	0, 0, r0, cr0, cr0, 0")			\
+	TEST_COPROCESSOR( "mrc"two"	15, 7, r15, cr15, cr15, 7")		\
+	TEST_COPROCESSOR( "mrc"two"	0, 0, r0, cr0, cr0, 0")
+
+	COPROCESSOR_INSTRUCTIONS_ST_LD("","e")
+	COPROCESSOR_INSTRUCTIONS_MC_MR("","e")
+	TEST_UNSUPPORTED("svc	0")
+	TEST_UNSUPPORTED("svc	0xffffff")
+
+	TEST_UNSUPPORTED("svc	0")
+
+	TEST_GROUP("Unconditional instruction")
+
+#if __LINUX_ARM_ARCH__ >= 6
+	TEST_UNSUPPORTED("srsda	sp, 0x13")
+	TEST_UNSUPPORTED("srsdb	sp, 0x13")
+	TEST_UNSUPPORTED("srsia	sp, 0x13")
+	TEST_UNSUPPORTED("srsib	sp, 0x13")
+	TEST_UNSUPPORTED("srsda	sp!, 0x13")
+	TEST_UNSUPPORTED("srsdb	sp!, 0x13")
+	TEST_UNSUPPORTED("srsia	sp!, 0x13")
+	TEST_UNSUPPORTED("srsib	sp!, 0x13")
+
+	TEST_UNSUPPORTED("rfeda	sp")
+	TEST_UNSUPPORTED("rfedb	sp")
+	TEST_UNSUPPORTED("rfeia	sp")
+	TEST_UNSUPPORTED("rfeib	sp")
+	TEST_UNSUPPORTED("rfeda	sp!")
+	TEST_UNSUPPORTED("rfedb	sp!")
+	TEST_UNSUPPORTED("rfeia	sp!")
+	TEST_UNSUPPORTED("rfeib	sp!")
+	TEST_UNSUPPORTED(".word 0xf81d0a00	@ rfeda	pc")
+	TEST_UNSUPPORTED(".word 0xf91d0a00	@ rfedb	pc")
+	TEST_UNSUPPORTED(".word 0xf89d0a00	@ rfeia	pc")
+	TEST_UNSUPPORTED(".word 0xf99d0a00	@ rfeib	pc")
+	TEST_UNSUPPORTED(".word 0xf83d0a00	@ rfeda	pc!")
+	TEST_UNSUPPORTED(".word 0xf93d0a00	@ rfedb	pc!")
+	TEST_UNSUPPORTED(".word 0xf8bd0a00	@ rfeia	pc!")
+	TEST_UNSUPPORTED(".word 0xf9bd0a00	@ rfeib	pc!")
+#endif /* __LINUX_ARM_ARCH__ >= 6 */
+
+#if __LINUX_ARM_ARCH__ >= 6
+	TEST_X(	"blx	__dummy_thumb_subroutine_even",
+		".thumb				\n\t"
+		".space 4			\n\t"
+		".type __dummy_thumb_subroutine_even, %%function \n\t"
+		"__dummy_thumb_subroutine_even:	\n\t"
+		"mov	r0, pc			\n\t"
+		"bx	lr			\n\t"
+		".arm				\n\t"
+	)
+	TEST(	"blx	__dummy_thumb_subroutine_even")
+
+	TEST_X(	"blx	__dummy_thumb_subroutine_odd",
+		".thumb				\n\t"
+		".space 2			\n\t"
+		".type __dummy_thumb_subroutine_odd, %%function	\n\t"
+		"__dummy_thumb_subroutine_odd:	\n\t"
+		"mov	r0, pc			\n\t"
+		"bx	lr			\n\t"
+		".arm				\n\t"
+	)
+	TEST(	"blx	__dummy_thumb_subroutine_odd")
+#endif /* __LINUX_ARM_ARCH__ >= 6 */
+
+	COPROCESSOR_INSTRUCTIONS_ST_LD("2","f")
+#if __LINUX_ARM_ARCH__ >= 6
+	COPROCESSOR_INSTRUCTIONS_MC_MR("2","f")
+#endif
+
+	TEST_GROUP("Miscellaneous instructions, memory hints, and Advanced SIMD instructions")
+
+#if __LINUX_ARM_ARCH__ >= 6
+	TEST_UNSUPPORTED("cps	0x13")
+	TEST_UNSUPPORTED("cpsie	i")
+	TEST_UNSUPPORTED("cpsid	i")
+	TEST_UNSUPPORTED("cpsie	i,0x13")
+	TEST_UNSUPPORTED("cpsid	i,0x13")
+	TEST_UNSUPPORTED("setend	le")
+	TEST_UNSUPPORTED("setend	be")
+#endif
+
+#if __LINUX_ARM_ARCH__ >= 7
+	TEST_P("pli	[r",0,0b,", #16]")
+	TEST(  "pli	[pc, #0]")
+	TEST_RR("pli	[r",12,0b,", r",0, 16,"]")
+	TEST_RR("pli	[r",0, 0b,", -r",12,16,", lsl #4]")
+#endif
+
+#if __LINUX_ARM_ARCH__ >= 5
+	TEST_P("pld	[r",0,32,", #-16]")
+	TEST(  "pld	[pc, #0]")
+	TEST_PR("pld	[r",7, 24, ", r",0, 16,"]")
+	TEST_PR("pld	[r",8, 24, ", -r",12,16,", lsl #4]")
+#endif
+
+#if __LINUX_ARM_ARCH__ >= 7
+	TEST_SUPPORTED(  ".word 0xf590f000	@ pldw [r0, #0]")
+	TEST_SUPPORTED(  ".word 0xf797f000	@ pldw	[r7, r0]")
+	TEST_SUPPORTED(  ".word 0xf798f18c	@ pldw	[r8, r12, lsl #3]");
+#endif
+
+#if __LINUX_ARM_ARCH__ >= 7
+	TEST_UNSUPPORTED("clrex")
+	TEST_UNSUPPORTED("dsb")
+	TEST_UNSUPPORTED("dmb")
+	TEST_UNSUPPORTED("isb")
+#endif
+
+	verbose("\n");
+}
+
diff --git a/arch/arm/kernel/kprobes-test-thumb.c b/arch/arm/kernel/kprobes-test-thumb.c
new file mode 100644
index 0000000..5e726c3
--- /dev/null
+++ b/arch/arm/kernel/kprobes-test-thumb.c
@@ -0,0 +1,1187 @@
+/*
+ * arch/arm/kernel/kprobes-test-thumb.c
+ *
+ * Copyright (C) 2011 Jon Medhurst <tixy@yxit.co.uk>.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+
+#include "kprobes-test.h"
+
+
+#define TEST_ISA "16"
+
+#define DONT_TEST_IN_ITBLOCK(tests)			\
+	kprobe_test_flags |= TEST_FLAG_NO_ITBLOCK;	\
+	tests						\
+	kprobe_test_flags &= ~TEST_FLAG_NO_ITBLOCK;
+
+#define CONDITION_INSTRUCTIONS(cc_pos, tests)		\
+	kprobe_test_cc_position = cc_pos;		\
+	DONT_TEST_IN_ITBLOCK(tests)			\
+	kprobe_test_cc_position = 0;
+
+#define TEST_ITBLOCK(code)				\
+	kprobe_test_flags |= TEST_FLAG_FULL_ITBLOCK;	\
+	TESTCASE_START(code)				\
+	TEST_ARG_END("")				\
+	"50:	nop			\n\t"		\
+	"1:	"code"			\n\t"		\
+	"	mov r1, #0x11		\n\t"		\
+	"	mov r2, #0x22		\n\t"		\
+	"	mov r3, #0x33		\n\t"		\
+	"2:	nop			\n\t"		\
+	TESTCASE_END					\
+	kprobe_test_flags &= ~TEST_FLAG_FULL_ITBLOCK;
+
+#define TEST_THUMB_TO_ARM_INTERWORK_P(code1, reg, val, code2)	\
+	TESTCASE_START(code1 #reg code2)			\
+	TEST_ARG_PTR(reg, val)					\
+	TEST_ARG_REG(14, 99f+1)					\
+	TEST_ARG_MEM(15, 3f)					\
+	TEST_ARG_END("")					\
+	"	nop			\n\t" /* To align 1f */	\
+	"50:	nop			\n\t"			\
+	"1:	"code1 #reg code2"	\n\t"			\
+	"	bx	lr		\n\t"			\
+	".arm				\n\t"			\
+	"3:	adr	lr, 2f+1	\n\t"			\
+	"	bx	lr		\n\t"			\
+	".thumb				\n\t"			\
+	"2:	nop			\n\t"			\
+	TESTCASE_END
+
+
+void kprobe_thumb16_test_cases(void)
+{
+	kprobe_test_flags = TEST_FLAG_NARROW_INSTR;
+
+	TEST_GROUP("Shift (immediate), add, subtract, move, and compare")
+
+	TEST_R(    "lsls	r7, r",0,VAL1,", #5")
+	TEST_R(    "lsls	r0, r",7,VAL2,", #11")
+	TEST_R(    "lsrs	r7, r",0,VAL1,", #5")
+	TEST_R(    "lsrs	r0, r",7,VAL2,", #11")
+	TEST_R(    "asrs	r7, r",0,VAL1,", #5")
+	TEST_R(    "asrs	r0, r",7,VAL2,", #11")
+	TEST_RR(   "adds	r2, r",0,VAL1,", r",7,VAL2,"")
+	TEST_RR(   "adds	r5, r",7,VAL2,", r",0,VAL2,"")
+	TEST_RR(   "subs	r2, r",0,VAL1,", r",7,VAL2,"")
+	TEST_RR(   "subs	r5, r",7,VAL2,", r",0,VAL2,"")
+	TEST_R(    "adds	r7, r",0,VAL1,", #5")
+	TEST_R(    "adds	r0, r",7,VAL2,", #2")
+	TEST_R(    "subs	r7, r",0,VAL1,", #5")
+	TEST_R(    "subs	r0, r",7,VAL2,", #2")
+	TEST(      "movs.n	r0, #0x5f")
+	TEST(      "movs.n	r7, #0xa0")
+	TEST_R(    "cmp.n	r",0,0x5e, ", #0x5f")
+	TEST_R(    "cmp.n	r",5,0x15f,", #0x5f")
+	TEST_R(    "cmp.n	r",7,0xa0, ", #0xa0")
+	TEST_R(    "adds.n	r",0,VAL1,", #0x5f")
+	TEST_R(    "adds.n	r",7,VAL2,", #0xa0")
+	TEST_R(    "subs.n	r",0,VAL1,", #0x5f")
+	TEST_R(    "subs.n	r",7,VAL2,", #0xa0")
+
+	TEST_GROUP("16-bit Thumb data-processing instructions")
+
+#define DATA_PROCESSING16(op,val)			\
+	TEST_RR(   op"	r",0,VAL1,", r",7,val,"")	\
+	TEST_RR(   op"	r",7,VAL2,", r",0,val,"")
+
+	DATA_PROCESSING16("ands",0xf00f00ff)
+	DATA_PROCESSING16("eors",0xf00f00ff)
+	DATA_PROCESSING16("lsls",11)
+	DATA_PROCESSING16("lsrs",11)
+	DATA_PROCESSING16("asrs",11)
+	DATA_PROCESSING16("adcs",VAL2)
+	DATA_PROCESSING16("sbcs",VAL2)
+	DATA_PROCESSING16("rors",11)
+	DATA_PROCESSING16("tst",0xf00f00ff)
+	TEST_R("rsbs	r",0,VAL1,", #0")
+	TEST_R("rsbs	r",7,VAL2,", #0")
+	DATA_PROCESSING16("cmp",0xf00f00ff)
+	DATA_PROCESSING16("cmn",0xf00f00ff)
+	DATA_PROCESSING16("orrs",0xf00f00ff)
+	DATA_PROCESSING16("muls",VAL2)
+	DATA_PROCESSING16("bics",0xf00f00ff)
+	DATA_PROCESSING16("mvns",VAL2)
+
+	TEST_GROUP("Special data instructions and branch and exchange")
+
+	TEST_RR(  "add	r",0, VAL1,", r",7,VAL2,"")
+	TEST_RR(  "add	r",3, VAL2,", r",8,VAL3,"")
+	TEST_RR(  "add	r",8, VAL3,", r",0,VAL1,"")
+	TEST_R(   "add	sp"        ", r",8,-8,  "")
+	TEST_R(   "add	r",14,VAL1,", pc")
+	TEST_BF_R("add	pc"        ", r",0,2f-1f-8,"")
+	TEST_UNSUPPORTED(".short 0x44ff	@ add pc, pc")
+
+	TEST_RR(  "cmp	r",3,VAL1,", r",8,VAL2,"")
+	TEST_RR(  "cmp	r",8,VAL2,", r",0,VAL1,"")
+	TEST_R(   "cmp	sp"       ", r",8,-8,  "")
+
+	TEST_R(   "mov	r0, r",7,VAL2,"")
+	TEST_R(   "mov	r3, r",8,VAL3,"")
+	TEST_R(   "mov	r8, r",0,VAL1,"")
+	TEST_P(   "mov	sp, r",8,-8,  "")
+	TEST(     "mov	lr, pc")
+	TEST_BF_R("mov	pc, r",0,2f,  "")
+
+	TEST_BF_R("bx	r",0, 2f+1,"")
+	TEST_BF_R("bx	r",14,2f+1,"")
+	TESTCASE_START("bx	pc")
+		TEST_ARG_REG(14, 99f+1)
+		TEST_ARG_END("")
+		"	nop			\n\t" /* To align the bx pc*/
+		"50:	nop			\n\t"
+		"1:	bx	pc		\n\t"
+		"	bx	lr		\n\t"
+		".arm				\n\t"
+		"	adr	lr, 2f+1	\n\t"
+		"	bx	lr		\n\t"
+		".thumb				\n\t"
+		"2:	nop			\n\t"
+	TESTCASE_END
+
+	TEST_BF_R("blx	r",0, 2f+1,"")
+	TEST_BB_R("blx	r",14,2f+1,"")
+	TEST_UNSUPPORTED(".short 0x47f8	@ blx pc")
+
+	TEST_GROUP("Load from Literal Pool")
+
+	TEST_X( "ldr	r0, 3f",
+		".align					\n\t"
+		"3:	.word	"__stringify(VAL1))
+	TEST_X( "ldr	r7, 3f",
+		".space 128				\n\t"
+		".align					\n\t"
+		"3:	.word	"__stringify(VAL2))
+
+	TEST_GROUP("16-bit Thumb Load/store instructions")
+
+	TEST_RPR("str	r",0, VAL1,", [r",1, 24,", r",2,  48,"]")
+	TEST_RPR("str	r",7, VAL2,", [r",6, 24,", r",5,  48,"]")
+	TEST_RPR("strh	r",0, VAL1,", [r",1, 24,", r",2,  48,"]")
+	TEST_RPR("strh	r",7, VAL2,", [r",6, 24,", r",5,  48,"]")
+	TEST_RPR("strb	r",0, VAL1,", [r",1, 24,", r",2,  48,"]")
+	TEST_RPR("strb	r",7, VAL2,", [r",6, 24,", r",5,  48,"]")
+	TEST_PR( "ldrsb	r0, [r",1, 24,", r",2,  48,"]")
+	TEST_PR( "ldrsb	r7, [r",6, 24,", r",5,  50,"]")
+	TEST_PR( "ldr	r0, [r",1, 24,", r",2,  48,"]")
+	TEST_PR( "ldr	r7, [r",6, 24,", r",5,  48,"]")
+	TEST_PR( "ldrh	r0, [r",1, 24,", r",2,  48,"]")
+	TEST_PR( "ldrh	r7, [r",6, 24,", r",5,  50,"]")
+	TEST_PR( "ldrb	r0, [r",1, 24,", r",2,  48,"]")
+	TEST_PR( "ldrb	r7, [r",6, 24,", r",5,  50,"]")
+	TEST_PR( "ldrsh	r0, [r",1, 24,", r",2,  48,"]")
+	TEST_PR( "ldrsh	r7, [r",6, 24,", r",5,  50,"]")
+
+	TEST_RP("str	r",0, VAL1,", [r",1, 24,", #120]")
+	TEST_RP("str	r",7, VAL2,", [r",6, 24,", #120]")
+	TEST_P( "ldr	r0, [r",1, 24,", #120]")
+	TEST_P( "ldr	r7, [r",6, 24,", #120]")
+	TEST_RP("strb	r",0, VAL1,", [r",1, 24,", #30]")
+	TEST_RP("strb	r",7, VAL2,", [r",6, 24,", #30]")
+	TEST_P( "ldrb	r0, [r",1, 24,", #30]")
+	TEST_P( "ldrb	r7, [r",6, 24,", #30]")
+	TEST_RP("strh	r",0, VAL1,", [r",1, 24,", #60]")
+	TEST_RP("strh	r",7, VAL2,", [r",6, 24,", #60]")
+	TEST_P( "ldrh	r0, [r",1, 24,", #60]")
+	TEST_P( "ldrh	r7, [r",6, 24,", #60]")
+
+	TEST_R( "str	r",0, VAL1,", [sp, #0]")
+	TEST_R( "str	r",7, VAL2,", [sp, #160]")
+	TEST(   "ldr	r0, [sp, #0]")
+	TEST(   "ldr	r7, [sp, #160]")
+
+	TEST_RP("str	r",0, VAL1,", [r",0, 24,"]")
+	TEST_P( "ldr	r0, [r",0, 24,"]")
+
+	TEST_GROUP("Generate PC-/SP-relative address")
+
+	TEST("add	r0, pc, #4")
+	TEST("add	r7, pc, #1020")
+	TEST("add	r0, sp, #4")
+	TEST("add	r7, sp, #1020")
+
+	TEST_GROUP("Miscellaneous 16-bit instructions")
+
+	TEST_UNSUPPORTED( "cpsie	i")
+	TEST_UNSUPPORTED( "cpsid	i")
+	TEST_UNSUPPORTED( "setend	le")
+	TEST_UNSUPPORTED( "setend	be")
+
+	TEST("add	sp, #"__stringify(TEST_MEMORY_SIZE)) /* Assumes TEST_MEMORY_SIZE < 0x400 */
+	TEST("sub	sp, #0x7f*4")
+
+DONT_TEST_IN_ITBLOCK(
+	TEST_BF_R(  "cbnz	r",0,0, ", 2f")
+	TEST_BF_R(  "cbz	r",2,-1,", 2f")
+	TEST_BF_RX( "cbnz	r",4,1, ", 2f",0x20)
+	TEST_BF_RX( "cbz	r",7,0, ", 2f",0x40)
+)
+	TEST_R("sxth	r0, r",7, HH1,"")
+	TEST_R("sxth	r7, r",0, HH2,"")
+	TEST_R("sxtb	r0, r",7, HH1,"")
+	TEST_R("sxtb	r7, r",0, HH2,"")
+	TEST_R("uxth	r0, r",7, HH1,"")
+	TEST_R("uxth	r7, r",0, HH2,"")
+	TEST_R("uxtb	r0, r",7, HH1,"")
+	TEST_R("uxtb	r7, r",0, HH2,"")
+	TEST_R("rev	r0, r",7, VAL1,"")
+	TEST_R("rev	r7, r",0, VAL2,"")
+	TEST_R("rev16	r0, r",7, VAL1,"")
+	TEST_R("rev16	r7, r",0, VAL2,"")
+	TEST_UNSUPPORTED(".short 0xba80")
+	TEST_UNSUPPORTED(".short 0xbabf")
+	TEST_R("revsh	r0, r",7, VAL1,"")
+	TEST_R("revsh	r7, r",0, VAL2,"")
+
+#define TEST_POPPC(code, offset)	\
+	TESTCASE_START(code)		\
+	TEST_ARG_PTR(13, offset)	\
+	TEST_ARG_END("")		\
+	TEST_BRANCH_F(code,0)		\
+	TESTCASE_END
+
+	TEST("push	{r0}")
+	TEST("push	{r7}")
+	TEST("push	{r14}")
+	TEST("push	{r0-r7,r14}")
+	TEST("push	{r0,r2,r4,r6,r14}")
+	TEST("push	{r1,r3,r5,r7}")
+	TEST("pop	{r0}")
+	TEST("pop	{r7}")
+	TEST("pop	{r0,r2,r4,r6}")
+	TEST_POPPC("pop	{pc}",15*4)
+	TEST_POPPC("pop	{r0-r7,pc}",7*4)
+	TEST_POPPC("pop	{r1,r3,r5,r7,pc}",11*4)
+	TEST_THUMB_TO_ARM_INTERWORK_P("pop	{pc}	@ ",13,15*4,"")
+	TEST_THUMB_TO_ARM_INTERWORK_P("pop	{r0-r7,pc}	@ ",13,7*4,"")
+
+	TEST_UNSUPPORTED("bkpt.n	0")
+	TEST_UNSUPPORTED("bkpt.n	255")
+
+	TEST_SUPPORTED("yield")
+	TEST("sev")
+	TEST("nop")
+	TEST("wfi")
+	TEST_SUPPORTED("wfe")
+	TEST_UNSUPPORTED(".short 0xbf50") /* Unassigned hints */
+	TEST_UNSUPPORTED(".short 0xbff0") /* Unassigned hints */
+
+#define TEST_IT(code, code2)			\
+	TESTCASE_START(code)			\
+	TEST_ARG_END("")			\
+	"50:	nop			\n\t"	\
+	"1:	"code"			\n\t"	\
+	"	"code2"			\n\t"	\
+	"2:	nop			\n\t"	\
+	TESTCASE_END
+
+DONT_TEST_IN_ITBLOCK(
+	TEST_IT("it	eq","moveq r0,#0")
+	TEST_IT("it	vc","movvc r0,#0")
+	TEST_IT("it	le","movle r0,#0")
+	TEST_IT("ite	eq","moveq r0,#0\n\t  movne r1,#1")
+	TEST_IT("itet	vc","movvc r0,#0\n\t  movvs r1,#1\n\t  movvc r2,#2")
+	TEST_IT("itete	le","movle r0,#0\n\t  movgt r1,#1\n\t  movle r2,#2\n\t  movgt r3,#3")
+	TEST_IT("itttt	le","movle r0,#0\n\t  movle r1,#1\n\t  movle r2,#2\n\t  movle r3,#3")
+	TEST_IT("iteee	le","movle r0,#0\n\t  movgt r1,#1\n\t  movgt r2,#2\n\t  movgt r3,#3")
+)
+
+	TEST_GROUP("Load and store multiple")
+
+	TEST_P("ldmia	r",4, 16*4,"!, {r0,r7}")
+	TEST_P("ldmia	r",7, 16*4,"!, {r0-r6}")
+	TEST_P("stmia	r",4, 16*4,"!, {r0,r7}")
+	TEST_P("stmia	r",0, 16*4,"!, {r0-r7}")
+
+	TEST_GROUP("Conditional branch and Supervisor Call instructions")
+
+CONDITION_INSTRUCTIONS(8,
+	TEST_BF("beq	2f")
+	TEST_BB("bne	2b")
+	TEST_BF("bgt	2f")
+	TEST_BB("blt	2b")
+)
+	TEST_UNSUPPORTED(".short 0xde00")
+	TEST_UNSUPPORTED(".short 0xdeff")
+	TEST_UNSUPPORTED("svc	#0x00")
+	TEST_UNSUPPORTED("svc	#0xff")
+
+	TEST_GROUP("Unconditional branch")
+
+	TEST_BF(  "b	2f")
+	TEST_BB(  "b	2b")
+	TEST_BF_X("b	2f", 0x400)
+	TEST_BB_X("b	2b", 0x400)
+
+	TEST_GROUP("Testing instructions in IT blocks")
+
+	TEST_ITBLOCK("subs.n r0, r0")
+
+	verbose("\n");
+}
+
+
+void kprobe_thumb32_test_cases(void)
+{
+	kprobe_test_flags = 0;
+
+	TEST_GROUP("Load/store multiple")
+
+	TEST_UNSUPPORTED("rfedb	sp")
+	TEST_UNSUPPORTED("rfeia	sp")
+	TEST_UNSUPPORTED("rfedb	sp!")
+	TEST_UNSUPPORTED("rfeia	sp!")
+
+	TEST_P(   "stmia	r",0, 16*4,", {r0,r8}")
+	TEST_P(   "stmia	r",4, 16*4,", {r0-r12,r14}")
+	TEST_P(   "stmia	r",7, 16*4,"!, {r8-r12,r14}")
+	TEST_P(   "stmia	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+
+	TEST_P(   "ldmia	r",0, 16*4,", {r0,r8}")
+	TEST_P(   "ldmia	r",4, 0,   ", {r0-r12,r14}")
+	TEST_BF_P("ldmia	r",5, 8*4, "!, {r6-r12,r15}")
+	TEST_P(   "ldmia	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+	TEST_BF_P("ldmia	r",14,14*4,"!, {r4,pc}")
+
+	TEST_P(   "stmdb	r",0, 16*4,", {r0,r8}")
+	TEST_P(   "stmdb	r",4, 16*4,", {r0-r12,r14}")
+	TEST_P(   "stmdb	r",5, 16*4,"!, {r8-r12,r14}")
+	TEST_P(   "stmdb	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+
+	TEST_P(   "ldmdb	r",0, 16*4,", {r0,r8}")
+	TEST_P(   "ldmdb	r",4, 16*4,", {r0-r12,r14}")
+	TEST_BF_P("ldmdb	r",5, 16*4,"!, {r6-r12,r15}")
+	TEST_P(   "ldmdb	r",12,16*4,"!, {r1,r3,r5,r7,r8-r11,r14}")
+	TEST_BF_P("ldmdb	r",14,16*4,"!, {r4,pc}")
+
+	TEST_P(   "stmdb	r",13,16*4,"!, {r3-r12,lr}")
+	TEST_P(	  "stmdb	r",13,16*4,"!, {r3-r12}")
+	TEST_P(   "stmdb	r",2, 16*4,", {r3-r12,lr}")
+	TEST_P(   "stmdb	r",13,16*4,"!, {r2-r12,lr}")
+	TEST_P(   "stmdb	r",0, 16*4,", {r0-r12}")
+	TEST_P(   "stmdb	r",0, 16*4,", {r0-r12,lr}")
+
+	TEST_BF_P("ldmia	r",13,5*4, "!, {r3-r12,pc}")
+	TEST_P(	  "ldmia	r",13,5*4, "!, {r3-r12}")
+	TEST_BF_P("ldmia	r",2, 5*4, "!, {r3-r12,pc}")
+	TEST_BF_P("ldmia	r",13,4*4, "!, {r2-r12,pc}")
+	TEST_P(   "ldmia	r",0, 16*4,", {r0-r12}")
+	TEST_P(   "ldmia	r",0, 16*4,", {r0-r12,lr}")
+
+	TEST_THUMB_TO_ARM_INTERWORK_P("ldmia	r",0,14*4,", {r12,pc}")
+	TEST_THUMB_TO_ARM_INTERWORK_P("ldmia	r",13,2*4,", {r0-r12,pc}")
+
+	TEST_UNSUPPORTED(".short 0xe88f,0x0101	@ stmia	pc, {r0,r8}")
+	TEST_UNSUPPORTED(".short 0xe92f,0x5f00	@ stmdb	pc!, {r8-r12,r14}")
+	TEST_UNSUPPORTED(".short 0xe8bd,0xc000	@ ldmia	r13!, {r14,pc}")
+	TEST_UNSUPPORTED(".short 0xe93e,0xc000	@ ldmdb	r14!, {r14,pc}")
+	TEST_UNSUPPORTED(".short 0xe8a7,0x3f00	@ stmia	r7!, {r8-r12,sp}")
+	TEST_UNSUPPORTED(".short 0xe8a7,0x9f00	@ stmia	r7!, {r8-r12,pc}")
+	TEST_UNSUPPORTED(".short 0xe93e,0x2010	@ ldmdb	r14!, {r4,sp}")
+
+	TEST_GROUP("Load/store double or exclusive, table branch")
+
+	TEST_P(  "ldrd	r0, r1, [r",1, 24,", #-16]")
+	TEST(    "ldrd	r12, r14, [sp, #16]")
+	TEST_P(  "ldrd	r1, r0, [r",7, 24,", #-16]!")
+	TEST(    "ldrd	r14, r12, [sp, #16]!")
+	TEST_P(  "ldrd	r1, r0, [r",7, 24,"], #16")
+	TEST(    "ldrd	r7, r8, [sp], #-16")
+
+	TEST_X( "ldrd	r12, r14, 3f",
+		".align 3				\n\t"
+		"3:	.word	"__stringify(VAL1)"	\n\t"
+		"	.word	"__stringify(VAL2))
+
+	TEST_UNSUPPORTED(".short 0xe9ff,0xec04	@ ldrd	r14, r12, [pc, #16]!")
+	TEST_UNSUPPORTED(".short 0xe8ff,0xec04	@ ldrd	r14, r12, [pc], #16")
+	TEST_UNSUPPORTED(".short 0xe9d4,0xd800	@ ldrd	sp, r8, [r4]")
+	TEST_UNSUPPORTED(".short 0xe9d4,0xf800	@ ldrd	pc, r8, [r4]")
+	TEST_UNSUPPORTED(".short 0xe9d4,0x7d00	@ ldrd	r7, sp, [r4]")
+	TEST_UNSUPPORTED(".short 0xe9d4,0x7f00	@ ldrd	r7, pc, [r4]")
+
+	TEST_RRP("strd	r",0, VAL1,", r",1, VAL2,", [r",1, 24,", #-16]")
+	TEST_RR( "strd	r",12,VAL2,", r",14,VAL1,", [sp, #16]")
+	TEST_RRP("strd	r",1, VAL1,", r",0, VAL2,", [r",7, 24,", #-16]!")
+	TEST_RR( "strd	r",14,VAL2,", r",12,VAL1,", [sp, #16]!")
+	TEST_RRP("strd	r",1, VAL1,", r",0, VAL2,", [r",7, 24,"], #16")
+	TEST_RR( "strd	r",7, VAL2,", r",8, VAL1,", [sp], #-16")
+	TEST_UNSUPPORTED(".short 0xe9ef,0xec04	@ strd	r14, r12, [pc, #16]!")
+	TEST_UNSUPPORTED(".short 0xe8ef,0xec04	@ strd	r14, r12, [pc], #16")
+
+	TEST_RX("tbb	[pc, r",0, (9f-(1f+4)),"]",
+		"9:			\n\t"
+		".byte	(2f-1b-4)>>1	\n\t"
+		".byte	(3f-1b-4)>>1	\n\t"
+		"3:	mvn	r0, r0	\n\t"
+		"2:	nop		\n\t")
+
+	TEST_RX("tbb	[pc, r",4, (9f-(1f+4)+1),"]",
+		"9:			\n\t"
+		".byte	(2f-1b-4)>>1	\n\t"
+		".byte	(3f-1b-4)>>1	\n\t"
+		"3:	mvn	r0, r0	\n\t"
+		"2:	nop		\n\t")
+
+	TEST_RRX("tbb	[r",1,9f,", r",2,0,"]",
+		"9:			\n\t"
+		".byte	(2f-1b-4)>>1	\n\t"
+		".byte	(3f-1b-4)>>1	\n\t"
+		"3:	mvn	r0, r0	\n\t"
+		"2:	nop		\n\t")
+
+	TEST_RX("tbh	[pc, r",7, (9f-(1f+4))>>1,"]",
+		"9:			\n\t"
+		".short	(2f-1b-4)>>1	\n\t"
+		".short	(3f-1b-4)>>1	\n\t"
+		"3:	mvn	r0, r0	\n\t"
+		"2:	nop		\n\t")
+
+	TEST_RX("tbh	[pc, r",12, ((9f-(1f+4))>>1)+1,"]",
+		"9:			\n\t"
+		".short	(2f-1b-4)>>1	\n\t"
+		".short	(3f-1b-4)>>1	\n\t"
+		"3:	mvn	r0, r0	\n\t"
+		"2:	nop		\n\t")
+
+	TEST_RRX("tbh	[r",1,9f, ", r",14,1,"]",
+		"9:			\n\t"
+		".short	(2f-1b-4)>>1	\n\t"
+		".short	(3f-1b-4)>>1	\n\t"
+		"3:	mvn	r0, r0	\n\t"
+		"2:	nop		\n\t")
+
+	TEST_UNSUPPORTED(".short 0xe8d1,0xf01f	@ tbh [r1, pc]")
+	TEST_UNSUPPORTED(".short 0xe8d1,0xf01d	@ tbh [r1, sp]")
+	TEST_UNSUPPORTED(".short 0xe8dd,0xf012	@ tbh [sp, r2]")
+
+	TEST_UNSUPPORTED("strexb	r0, r1, [r2]")
+	TEST_UNSUPPORTED("strexh	r0, r1, [r2]")
+	TEST_UNSUPPORTED("strexd	r0, r1, [r2]")
+	TEST_UNSUPPORTED("ldrexb	r0, [r1]")
+	TEST_UNSUPPORTED("ldrexh	r0, [r1]")
+	TEST_UNSUPPORTED("ldrexd	r0, [r1]")
+
+	TEST_GROUP("Data-processing (shifted register) and (modified immediate)")
+
+#define _DATA_PROCESSING32_DNM(op,s,val)					\
+	TEST_RR(op s".w	r0,  r",1, VAL1,", r",2, val, "")			\
+	TEST_RR(op s"	r1,  r",1, VAL1,", r",2, val, ", lsl #3")		\
+	TEST_RR(op s"	r2,  r",3, VAL1,", r",2, val, ", lsr #4")		\
+	TEST_RR(op s"	r3,  r",3, VAL1,", r",2, val, ", asr #5")		\
+	TEST_RR(op s"	r4,  r",5, VAL1,", r",2, N(val),", asr #6")		\
+	TEST_RR(op s"	r5,  r",5, VAL1,", r",2, val, ", ror #7")		\
+	TEST_RR(op s"	r8,  r",9, VAL1,", r",10,val, ", rrx")			\
+	TEST_R( op s"	r0,  r",11,VAL1,", #0x00010001")			\
+	TEST_R( op s"	r11, r",0, VAL1,", #0xf5000000")			\
+	TEST_R( op s"	r7,  r",8, VAL2,", #0x000af000")
+
+#define DATA_PROCESSING32_DNM(op,val)		\
+	_DATA_PROCESSING32_DNM(op,"",val)	\
+	_DATA_PROCESSING32_DNM(op,"s",val)
+
+#define DATA_PROCESSING32_NM(op,val)					\
+	TEST_RR(op".w	r",1, VAL1,", r",2, val, "")			\
+	TEST_RR(op"	r",1, VAL1,", r",2, val, ", lsl #3")		\
+	TEST_RR(op"	r",3, VAL1,", r",2, val, ", lsr #4")		\
+	TEST_RR(op"	r",3, VAL1,", r",2, val, ", asr #5")		\
+	TEST_RR(op"	r",5, VAL1,", r",2, N(val),", asr #6")		\
+	TEST_RR(op"	r",5, VAL1,", r",2, val, ", ror #7")		\
+	TEST_RR(op"	r",9, VAL1,", r",10,val, ", rrx")		\
+	TEST_R( op"	r",11,VAL1,", #0x00010001")			\
+	TEST_R( op"	r",0, VAL1,", #0xf5000000")			\
+	TEST_R( op"	r",8, VAL2,", #0x000af000")
+
+#define _DATA_PROCESSING32_DM(op,s,val)				\
+	TEST_R( op s".w	r0,  r",14, val, "")			\
+	TEST_R( op s"	r1,  r",12, val, ", lsl #3")		\
+	TEST_R( op s"	r2,  r",11, val, ", lsr #4")		\
+	TEST_R( op s"	r3,  r",10, val, ", asr #5")		\
+	TEST_R( op s"	r4,  r",9, N(val),", asr #6")		\
+	TEST_R( op s"	r5,  r",8, val, ", ror #7")		\
+	TEST_R( op s"	r8,  r",7,val, ", rrx")			\
+	TEST(   op s"	r0,  #0x00010001")			\
+	TEST(   op s"	r11, #0xf5000000")			\
+	TEST(   op s"	r7,  #0x000af000")			\
+	TEST(   op s"	r4,  #0x00005a00")
+
+#define DATA_PROCESSING32_DM(op,val)		\
+	_DATA_PROCESSING32_DM(op,"",val)	\
+	_DATA_PROCESSING32_DM(op,"s",val)
+
+	DATA_PROCESSING32_DNM("and",0xf00f00ff)
+	DATA_PROCESSING32_NM("tst",0xf00f00ff)
+	DATA_PROCESSING32_DNM("bic",0xf00f00ff)
+	DATA_PROCESSING32_DNM("orr",0xf00f00ff)
+	DATA_PROCESSING32_DM("mov",VAL2)
+	DATA_PROCESSING32_DNM("orn",0xf00f00ff)
+	DATA_PROCESSING32_DM("mvn",VAL2)
+	DATA_PROCESSING32_DNM("eor",0xf00f00ff)
+	DATA_PROCESSING32_NM("teq",0xf00f00ff)
+	DATA_PROCESSING32_DNM("add",VAL2)
+	DATA_PROCESSING32_NM("cmn",VAL2)
+	DATA_PROCESSING32_DNM("adc",VAL2)
+	DATA_PROCESSING32_DNM("sbc",VAL2)
+	DATA_PROCESSING32_DNM("sub",VAL2)
+	DATA_PROCESSING32_NM("cmp",VAL2)
+	DATA_PROCESSING32_DNM("rsb",VAL2)
+
+	TEST_RR("pkhbt	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR("pkhbt	r14,r",12, HH1,", r",10,HH2,", lsl #2")
+	TEST_RR("pkhtb	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR("pkhtb	r14,r",12, HH1,", r",10,HH2,", asr #2")
+
+	TEST_UNSUPPORTED(".short 0xea17,0x0f0d	@ tst.w r7, sp")
+	TEST_UNSUPPORTED(".short 0xea17,0x0f0f	@ tst.w r7, pc")
+	TEST_UNSUPPORTED(".short 0xea1d,0x0f07	@ tst.w sp, r7")
+	TEST_UNSUPPORTED(".short 0xea1f,0x0f07	@ tst.w pc, r7")
+	TEST_UNSUPPORTED(".short 0xf01d,0x1f08	@ tst sp, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf01f,0x1f08	@ tst pc, #0x00080008")
+
+	TEST_UNSUPPORTED(".short 0xea97,0x0f0d	@ teq.w r7, sp")
+	TEST_UNSUPPORTED(".short 0xea97,0x0f0f	@ teq.w r7, pc")
+	TEST_UNSUPPORTED(".short 0xea9d,0x0f07	@ teq.w sp, r7")
+	TEST_UNSUPPORTED(".short 0xea9f,0x0f07	@ teq.w pc, r7")
+	TEST_UNSUPPORTED(".short 0xf09d,0x1f08	@ tst sp, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf09f,0x1f08	@ tst pc, #0x00080008")
+
+	TEST_UNSUPPORTED(".short 0xeb17,0x0f0d	@ cmn.w r7, sp")
+	TEST_UNSUPPORTED(".short 0xeb17,0x0f0f	@ cmn.w r7, pc")
+	TEST_P("cmn.w	sp, r",7,0,"")
+	TEST_UNSUPPORTED(".short 0xeb1f,0x0f07	@ cmn.w pc, r7")
+	TEST(  "cmn	sp, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf11f,0x1f08	@ cmn pc, #0x00080008")
+
+	TEST_UNSUPPORTED(".short 0xebb7,0x0f0d	@ cmp.w r7, sp")
+	TEST_UNSUPPORTED(".short 0xebb7,0x0f0f	@ cmp.w r7, pc")
+	TEST_P("cmp.w	sp, r",7,0,"")
+	TEST_UNSUPPORTED(".short 0xebbf,0x0f07	@ cmp.w pc, r7")
+	TEST(  "cmp	sp, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf1bf,0x1f08	@ cmp pc, #0x00080008")
+
+	TEST_UNSUPPORTED(".short 0xea5f,0x070d	@ movs.w r7, sp")
+	TEST_UNSUPPORTED(".short 0xea5f,0x070f	@ movs.w r7, pc")
+	TEST_UNSUPPORTED(".short 0xea5f,0x0d07	@ movs.w sp, r7")
+	TEST_UNSUPPORTED(".short 0xea4f,0x0f07	@ mov.w  pc, r7")
+	TEST_UNSUPPORTED(".short 0xf04f,0x1d08	@ mov sp, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf04f,0x1f08	@ mov pc, #0x00080008")
+
+	TEST_R("add.w	r0, sp, r",1, 4,"")
+	TEST_R("adds	r0, sp, r",1, 4,", asl #3")
+	TEST_R("add	r0, sp, r",1, 4,", asl #4")
+	TEST_R("add	r0, sp, r",1, 16,", ror #1")
+	TEST_R("add.w	sp, sp, r",1, 4,"")
+	TEST_R("add	sp, sp, r",1, 4,", asl #3")
+	TEST_UNSUPPORTED(".short 0xeb0d,0x1d01	@ add sp, sp, r1, asl #4")
+	TEST_UNSUPPORTED(".short 0xeb0d,0x0d71	@ add sp, sp, r1, ror #1")
+	TEST(  "add.w	r0, sp, #24")
+	TEST(  "add.w	sp, sp, #24")
+	TEST_UNSUPPORTED(".short 0xeb0d,0x0f01	@ add pc, sp, r1")
+	TEST_UNSUPPORTED(".short 0xeb0d,0x000f	@ add r0, sp, pc")
+	TEST_UNSUPPORTED(".short 0xeb0d,0x000d	@ add r0, sp, sp")
+	TEST_UNSUPPORTED(".short 0xeb0d,0x0d0f	@ add sp, sp, pc")
+	TEST_UNSUPPORTED(".short 0xeb0d,0x0d0d	@ add sp, sp, sp")
+
+	TEST_R("sub.w	r0, sp, r",1, 4,"")
+	TEST_R("subs	r0, sp, r",1, 4,", asl #3")
+	TEST_R("sub	r0, sp, r",1, 4,", asl #4")
+	TEST_R("sub	r0, sp, r",1, 16,", ror #1")
+	TEST_R("sub.w	sp, sp, r",1, 4,"")
+	TEST_R("sub	sp, sp, r",1, 4,", asl #3")
+	TEST_UNSUPPORTED(".short 0xebad,0x1d01	@ sub sp, sp, r1, asl #4")
+	TEST_UNSUPPORTED(".short 0xebad,0x0d71	@ sub sp, sp, r1, ror #1")
+	TEST_UNSUPPORTED(".short 0xebad,0x0f01	@ sub pc, sp, r1")
+	TEST(  "sub.w	r0, sp, #24")
+	TEST(  "sub.w	sp, sp, #24")
+
+	TEST_UNSUPPORTED(".short 0xea02,0x010f	@ and r1, r2, pc")
+	TEST_UNSUPPORTED(".short 0xea0f,0x0103	@ and r1, pc, r3")
+	TEST_UNSUPPORTED(".short 0xea02,0x0f03	@ and pc, r2, r3")
+	TEST_UNSUPPORTED(".short 0xea02,0x010d	@ and r1, r2, sp")
+	TEST_UNSUPPORTED(".short 0xea0d,0x0103	@ and r1, sp, r3")
+	TEST_UNSUPPORTED(".short 0xea02,0x0d03	@ and sp, r2, r3")
+	TEST_UNSUPPORTED(".short 0xf00d,0x1108	@ and r1, sp, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf00f,0x1108	@ and r1, pc, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf002,0x1d08	@ and sp, r8, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf002,0x1f08	@ and pc, r8, #0x00080008")
+
+	TEST_UNSUPPORTED(".short 0xeb02,0x010f	@ add r1, r2, pc")
+	TEST_UNSUPPORTED(".short 0xeb0f,0x0103	@ add r1, pc, r3")
+	TEST_UNSUPPORTED(".short 0xeb02,0x0f03	@ add pc, r2, r3")
+	TEST_UNSUPPORTED(".short 0xeb02,0x010d	@ add r1, r2, sp")
+	TEST_SUPPORTED(  ".short 0xeb0d,0x0103	@ add r1, sp, r3")
+	TEST_UNSUPPORTED(".short 0xeb02,0x0d03	@ add sp, r2, r3")
+	TEST_SUPPORTED(  ".short 0xf10d,0x1108	@ add r1, sp, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf10d,0x1f08	@ add pc, sp, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf10f,0x1108	@ add r1, pc, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf102,0x1d08	@ add sp, r8, #0x00080008")
+	TEST_UNSUPPORTED(".short 0xf102,0x1f08	@ add pc, r8, #0x00080008")
+
+	TEST_UNSUPPORTED(".short 0xeaa0,0x0000")
+	TEST_UNSUPPORTED(".short 0xeaf0,0x0000")
+	TEST_UNSUPPORTED(".short 0xeb20,0x0000")
+	TEST_UNSUPPORTED(".short 0xeb80,0x0000")
+	TEST_UNSUPPORTED(".short 0xebe0,0x0000")
+
+	TEST_UNSUPPORTED(".short 0xf0a0,0x0000")
+	TEST_UNSUPPORTED(".short 0xf0c0,0x0000")
+	TEST_UNSUPPORTED(".short 0xf0f0,0x0000")
+	TEST_UNSUPPORTED(".short 0xf120,0x0000")
+	TEST_UNSUPPORTED(".short 0xf180,0x0000")
+	TEST_UNSUPPORTED(".short 0xf1e0,0x0000")
+
+	TEST_GROUP("Coprocessor instructions")
+
+	TEST_UNSUPPORTED(".short 0xec00,0x0000")
+	TEST_UNSUPPORTED(".short 0xeff0,0x0000")
+	TEST_UNSUPPORTED(".short 0xfc00,0x0000")
+	TEST_UNSUPPORTED(".short 0xfff0,0x0000")
+
+	TEST_GROUP("Data-processing (plain binary immediate)")
+
+	TEST_R("addw	r0,  r",1, VAL1,", #0x123")
+	TEST(  "addw	r14, sp, #0xf5a")
+	TEST(  "addw	sp, sp, #0x20")
+	TEST(  "addw	r7,  pc, #0x888")
+	TEST_UNSUPPORTED(".short 0xf20f,0x1f20	@ addw pc, pc, #0x120")
+	TEST_UNSUPPORTED(".short 0xf20d,0x1f20	@ addw pc, sp, #0x120")
+	TEST_UNSUPPORTED(".short 0xf20f,0x1d20	@ addw sp, pc, #0x120")
+	TEST_UNSUPPORTED(".short 0xf200,0x1d20	@ addw sp, r0, #0x120")
+
+	TEST_R("subw	r0,  r",1, VAL1,", #0x123")
+	TEST(  "subw	r14, sp, #0xf5a")
+	TEST(  "subw	sp, sp, #0x20")
+	TEST(  "subw	r7,  pc, #0x888")
+	TEST_UNSUPPORTED(".short 0xf2af,0x1f20	@ subw pc, pc, #0x120")
+	TEST_UNSUPPORTED(".short 0xf2ad,0x1f20	@ subw pc, sp, #0x120")
+	TEST_UNSUPPORTED(".short 0xf2af,0x1d20	@ subw sp, pc, #0x120")
+	TEST_UNSUPPORTED(".short 0xf2a0,0x1d20	@ subw sp, r0, #0x120")
+
+	TEST("movw	r0, #0")
+	TEST("movw	r0, #0xffff")
+	TEST("movw	lr, #0xffff")
+	TEST_UNSUPPORTED(".short 0xf240,0x0d00	@ movw sp, #0")
+	TEST_UNSUPPORTED(".short 0xf240,0x0f00	@ movw pc, #0")
+
+	TEST_R("movt	r",0, VAL1,", #0")
+	TEST_R("movt	r",0, VAL2,", #0xffff")
+	TEST_R("movt	r",14,VAL1,", #0xffff")
+	TEST_UNSUPPORTED(".short 0xf2c0,0x0d00	@ movt sp, #0")
+	TEST_UNSUPPORTED(".short 0xf2c0,0x0f00	@ movt pc, #0")
+
+	TEST_R(     "ssat	r0, #24, r",0,   VAL1,"")
+	TEST_R(     "ssat	r14, #24, r",12, VAL2,"")
+	TEST_R(     "ssat	r0, #24, r",0,   VAL1,", lsl #8")
+	TEST_R(     "ssat	r14, #24, r",12, VAL2,", asr #8")
+	TEST_UNSUPPORTED(".short 0xf30c,0x0d17	@ ssat	sp, #24, r12")
+	TEST_UNSUPPORTED(".short 0xf30c,0x0f17	@ ssat	pc, #24, r12")
+	TEST_UNSUPPORTED(".short 0xf30d,0x0c17	@ ssat	r12, #24, sp")
+	TEST_UNSUPPORTED(".short 0xf30f,0x0c17	@ ssat	r12, #24, pc")
+
+	TEST_R(     "usat	r0, #24, r",0,   VAL1,"")
+	TEST_R(     "usat	r14, #24, r",12, VAL2,"")
+	TEST_R(     "usat	r0, #24, r",0,   VAL1,", lsl #8")
+	TEST_R(     "usat	r14, #24, r",12, VAL2,", asr #8")
+	TEST_UNSUPPORTED(".short 0xf38c,0x0d17	@ usat	sp, #24, r12")
+	TEST_UNSUPPORTED(".short 0xf38c,0x0f17	@ usat	pc, #24, r12")
+	TEST_UNSUPPORTED(".short 0xf38d,0x0c17	@ usat	r12, #24, sp")
+	TEST_UNSUPPORTED(".short 0xf38f,0x0c17	@ usat	r12, #24, pc")
+
+	TEST_R(     "ssat16	r0, #12, r",0,   HH1,"")
+	TEST_R(     "ssat16	r14, #12, r",12, HH2,"")
+	TEST_UNSUPPORTED(".short 0xf32c,0x0d0b	@ ssat16	sp, #12, r12")
+	TEST_UNSUPPORTED(".short 0xf32c,0x0f0b	@ ssat16	pc, #12, r12")
+	TEST_UNSUPPORTED(".short 0xf32d,0x0c0b	@ ssat16	r12, #12, sp")
+	TEST_UNSUPPORTED(".short 0xf32f,0x0c0b	@ ssat16	r12, #12, pc")
+
+	TEST_R(     "usat16	r0, #12, r",0,   HH1,"")
+	TEST_R(     "usat16	r14, #12, r",12, HH2,"")
+	TEST_UNSUPPORTED(".short 0xf3ac,0x0d0b	@ usat16	sp, #12, r12")
+	TEST_UNSUPPORTED(".short 0xf3ac,0x0f0b	@ usat16	pc, #12, r12")
+	TEST_UNSUPPORTED(".short 0xf3ad,0x0c0b	@ usat16	r12, #12, sp")
+	TEST_UNSUPPORTED(".short 0xf3af,0x0c0b	@ usat16	r12, #12, pc")
+
+	TEST_R(     "sbfx	r0, r",0  , VAL1,", #0, #31")
+	TEST_R(     "sbfx	r14, r",12, VAL2,", #8, #16")
+	TEST_R(     "sbfx	r4, r",10,  VAL1,", #16, #15")
+	TEST_UNSUPPORTED(".short 0xf34c,0x2d0f	@ sbfx	sp, r12, #8, #16")
+	TEST_UNSUPPORTED(".short 0xf34c,0x2f0f	@ sbfx	pc, r12, #8, #16")
+	TEST_UNSUPPORTED(".short 0xf34d,0x2c0f	@ sbfx	r12, sp, #8, #16")
+	TEST_UNSUPPORTED(".short 0xf34f,0x2c0f	@ sbfx	r12, pc, #8, #16")
+
+	TEST_R(     "ubfx	r0, r",0  , VAL1,", #0, #31")
+	TEST_R(     "ubfx	r14, r",12, VAL2,", #8, #16")
+	TEST_R(     "ubfx	r4, r",10,  VAL1,", #16, #15")
+	TEST_UNSUPPORTED(".short 0xf3cc,0x2d0f	@ ubfx	sp, r12, #8, #16")
+	TEST_UNSUPPORTED(".short 0xf3cc,0x2f0f	@ ubfx	pc, r12, #8, #16")
+	TEST_UNSUPPORTED(".short 0xf3cd,0x2c0f	@ ubfx	r12, sp, #8, #16")
+	TEST_UNSUPPORTED(".short 0xf3cf,0x2c0f	@ ubfx	r12, pc, #8, #16")
+
+	TEST_R(     "bfc	r",0, VAL1,", #4, #20")
+	TEST_R(     "bfc	r",14,VAL2,", #4, #20")
+	TEST_R(     "bfc	r",7, VAL1,", #0, #31")
+	TEST_R(     "bfc	r",8, VAL2,", #0, #31")
+	TEST_UNSUPPORTED(".short 0xf36f,0x0d1e	@ bfc	sp, #0, #31")
+	TEST_UNSUPPORTED(".short 0xf36f,0x0f1e	@ bfc	pc, #0, #31")
+
+	TEST_RR(    "bfi	r",0, VAL1,", r",0  , VAL2,", #0, #31")
+	TEST_RR(    "bfi	r",12,VAL1,", r",14 , VAL2,", #4, #20")
+	TEST_UNSUPPORTED(".short 0xf36e,0x1d17	@ bfi	sp, r14, #4, #20")
+	TEST_UNSUPPORTED(".short 0xf36e,0x1f17	@ bfi	pc, r14, #4, #20")
+	TEST_UNSUPPORTED(".short 0xf36d,0x1e17	@ bfi	r14, sp, #4, #20")
+
+	TEST_GROUP("Branches and miscellaneous control")
+
+CONDITION_INSTRUCTIONS(22,
+	TEST_BF("beq.w	2f")
+	TEST_BB("bne.w	2b")
+	TEST_BF("bgt.w	2f")
+	TEST_BB("blt.w	2b")
+	TEST_BF_X("bpl.w	2f",0x1000)
+)
+
+	TEST_UNSUPPORTED("msr	cpsr, r0")
+	TEST_UNSUPPORTED("msr	cpsr_f, r1")
+	TEST_UNSUPPORTED("msr	spsr, r2")
+
+	TEST_UNSUPPORTED("cpsie.w	i")
+	TEST_UNSUPPORTED("cpsid.w	i")
+	TEST_UNSUPPORTED("cps	0x13")
+
+	TEST_SUPPORTED("yield.w")
+	TEST("sev.w")
+	TEST("nop.w")
+	TEST("wfi.w")
+	TEST_SUPPORTED("wfe.w")
+	TEST_UNSUPPORTED("dbg.w	#0")
+
+	TEST_UNSUPPORTED("clrex")
+	TEST_UNSUPPORTED("dsb")
+	TEST_UNSUPPORTED("dmb")
+	TEST_UNSUPPORTED("isb")
+
+	TEST_UNSUPPORTED("bxj	r0")
+
+	TEST_UNSUPPORTED("subs	pc, lr, #4")
+
+	TEST("mrs	r0, cpsr")
+	TEST("mrs	r14, cpsr")
+	TEST_UNSUPPORTED(".short 0xf3ef,0x8d00	@ mrs	sp, spsr")
+	TEST_UNSUPPORTED(".short 0xf3ef,0x8f00	@ mrs	pc, spsr")
+	TEST_UNSUPPORTED("mrs	r0, spsr")
+	TEST_UNSUPPORTED("mrs	lr, spsr")
+
+	TEST_UNSUPPORTED(".short 0xf7f0,0x8000 @ smc #0")
+
+	TEST_UNSUPPORTED(".short 0xf7f0,0xa000 @ undefeined")
+
+	TEST_BF(  "b.w	2f")
+	TEST_BB(  "b.w	2b")
+	TEST_BF_X("b.w	2f", 0x1000)
+
+	TEST_BF(  "bl.w	2f")
+	TEST_BB(  "bl.w	2b")
+	TEST_BB_X("bl.w	2b", 0x1000)
+
+	TEST_X(	"blx	__dummy_arm_subroutine",
+		".arm				\n\t"
+		".align				\n\t"
+		".type __dummy_arm_subroutine, %%function \n\t"
+		"__dummy_arm_subroutine:	\n\t"
+		"mov	r0, pc			\n\t"
+		"bx	lr			\n\t"
+		".thumb				\n\t"
+	)
+	TEST(	"blx	__dummy_arm_subroutine")
+
+	TEST_GROUP("Store single data item")
+
+#define SINGLE_STORE(size)							\
+	TEST_RP( "str"size"	r",0, VAL1,", [r",11,-1024,", #1024]")		\
+	TEST_RP( "str"size"	r",14,VAL2,", [r",1, -1024,", #1080]")		\
+	TEST_RP( "str"size"	r",0, VAL1,", [r",11,256,  ", #-120]")		\
+	TEST_RP( "str"size"	r",14,VAL2,", [r",1, 256,  ", #-128]")		\
+	TEST_RP( "str"size"	r",0, VAL1,", [r",11,24,  "], #120")		\
+	TEST_RP( "str"size"	r",14,VAL2,", [r",1, 24,  "], #128")		\
+	TEST_RP( "str"size"	r",0, VAL1,", [r",11,24,  "], #-120")		\
+	TEST_RP( "str"size"	r",14,VAL2,", [r",1, 24,  "], #-128")		\
+	TEST_RP( "str"size"	r",0, VAL1,", [r",11,24,   ", #120]!")		\
+	TEST_RP( "str"size"	r",14,VAL2,", [r",1, 24,   ", #128]!")		\
+	TEST_RP( "str"size"	r",0, VAL1,", [r",11,256,  ", #-120]!")		\
+	TEST_RP( "str"size"	r",14,VAL2,", [r",1, 256,  ", #-128]!")		\
+	TEST_RPR("str"size".w	r",0, VAL1,", [r",1, 0,", r",2, 4,"]")		\
+	TEST_RPR("str"size"	r",14,VAL2,", [r",10,0,", r",11,4,", lsl #1]")	\
+	TEST_R(  "str"size".w	r",7, VAL1,", [sp, #24]")			\
+	TEST_RP( "str"size".w	r",0, VAL2,", [r",0,0, "]")			\
+	TEST_UNSUPPORTED("str"size"t	r0, [r1, #4]")
+
+	SINGLE_STORE("b")
+	SINGLE_STORE("h")
+	SINGLE_STORE("")
+
+	TEST("str	sp, [sp]")
+	TEST_UNSUPPORTED(".short 0xf8cf,0xe000	@ str	r14, [pc]")
+	TEST_UNSUPPORTED(".short 0xf8ce,0xf000	@ str	pc, [r14]")
+
+	TEST_GROUP("Advanced SIMD element or structure load/store instructions")
+
+	TEST_UNSUPPORTED(".short 0xf900,0x0000")
+	TEST_UNSUPPORTED(".short 0xf92f,0xffff")
+	TEST_UNSUPPORTED(".short 0xf980,0x0000")
+	TEST_UNSUPPORTED(".short 0xf9ef,0xffff")
+
+	TEST_GROUP("Load single data item and memory hints")
+
+#define SINGLE_LOAD(size)						\
+	TEST_P( "ldr"size"	r0, [r",11,-1024, ", #1024]")		\
+	TEST_P( "ldr"size"	r14, [r",1, -1024,", #1080]")		\
+	TEST_P( "ldr"size"	r0, [r",11,256,   ", #-120]")		\
+	TEST_P( "ldr"size"	r14, [r",1, 256,  ", #-128]")		\
+	TEST_P( "ldr"size"	r0, [r",11,24,   "], #120")		\
+	TEST_P( "ldr"size"	r14, [r",1, 24,  "], #128")		\
+	TEST_P( "ldr"size"	r0, [r",11,24,   "], #-120")		\
+	TEST_P( "ldr"size"	r14, [r",1,24,   "], #-128")		\
+	TEST_P( "ldr"size"	r0, [r",11,24,    ", #120]!")		\
+	TEST_P( "ldr"size"	r14, [r",1, 24,   ", #128]!")		\
+	TEST_P( "ldr"size"	r0, [r",11,256,   ", #-120]!")		\
+	TEST_P( "ldr"size"	r14, [r",1, 256,  ", #-128]!")		\
+	TEST_PR("ldr"size".w	r0, [r",1, 0,", r",2, 4,"]")		\
+	TEST_PR("ldr"size"	r14, [r",10,0,", r",11,4,", lsl #1]")	\
+	TEST_X( "ldr"size".w	r0, 3f",				\
+		".align 3				\n\t"		\
+		"3:	.word	"__stringify(VAL1))			\
+	TEST_X( "ldr"size".w	r14, 3f",				\
+		".align 3				\n\t"		\
+		"3:	.word	"__stringify(VAL2))			\
+	TEST(   "ldr"size".w	r7, 3b")				\
+	TEST(   "ldr"size".w	r7, [sp, #24]")				\
+	TEST_P( "ldr"size".w	r0, [r",0,0, "]")			\
+	TEST_UNSUPPORTED("ldr"size"t	r0, [r1, #4]")
+
+	SINGLE_LOAD("b")
+	SINGLE_LOAD("sb")
+	SINGLE_LOAD("h")
+	SINGLE_LOAD("sh")
+	SINGLE_LOAD("")
+
+	TEST_BF_P("ldr	pc, [r",14, 15*4,"]")
+	TEST_P(   "ldr	sp, [r",14, 13*4,"]")
+	TEST_BF_R("ldr	pc, [sp, r",14, 15*4,"]")
+	TEST_R(   "ldr	sp, [sp, r",14, 13*4,"]")
+	TEST_THUMB_TO_ARM_INTERWORK_P("ldr	pc, [r",0,0,", #15*4]")
+	TEST_SUPPORTED("ldr	sp, 99f")
+	TEST_SUPPORTED("ldr	pc, 99f")
+
+	TEST_UNSUPPORTED(".short 0xf854,0x700d	@ ldr	r7, [r4, sp]")
+	TEST_UNSUPPORTED(".short 0xf854,0x700f	@ ldr	r7, [r4, pc]")
+	TEST_UNSUPPORTED(".short 0xf814,0x700d	@ ldrb	r7, [r4, sp]")
+	TEST_UNSUPPORTED(".short 0xf814,0x700f	@ ldrb	r7, [r4, pc]")
+	TEST_UNSUPPORTED(".short 0xf89f,0xd004	@ ldrb	sp, 99f")
+	TEST_UNSUPPORTED(".short 0xf814,0xd008	@ ldrb	sp, [r4, r8]")
+	TEST_UNSUPPORTED(".short 0xf894,0xd000	@ ldrb	sp, [r4]")
+
+	TEST_UNSUPPORTED(".short 0xf860,0x0000") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xf9ff,0xffff") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xf950,0x0000") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xf95f,0xffff") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xf800,0x0800") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xf97f,0xfaff") /* Unallocated space */
+
+	TEST(   "pli	[pc, #4]")
+	TEST(   "pli	[pc, #-4]")
+	TEST(   "pld	[pc, #4]")
+	TEST(   "pld	[pc, #-4]")
+
+	TEST_P( "pld	[r",0,-1024,", #1024]")
+	TEST(   ".short 0xf8b0,0xf400	@ pldw	[r0, #1024]")
+	TEST_P( "pli	[r",4, 0b,", #1024]")
+	TEST_P( "pld	[r",7, 120,", #-120]")
+	TEST(   ".short 0xf837,0xfc78	@ pldw	[r7, #-120]")
+	TEST_P( "pli	[r",11,120,", #-120]")
+	TEST(   "pld	[sp, #0]")
+
+	TEST_PR("pld	[r",7, 24, ", r",0, 16,"]")
+	TEST_PR("pld	[r",8, 24, ", r",12,16,", lsl #3]")
+	TEST_SUPPORTED(".short 0xf837,0xf000	@ pldw	[r7, r0]")
+	TEST_SUPPORTED(".short 0xf838,0xf03c	@ pldw	[r8, r12, lsl #3]");
+	TEST_RR("pli	[r",12,0b,", r",0, 16,"]")
+	TEST_RR("pli	[r",0, 0b,", r",12,16,", lsl #3]")
+	TEST_R( "pld	[sp, r",1, 16,"]")
+	TEST_UNSUPPORTED(".short 0xf817,0xf00d  @pld	[r7, sp]")
+	TEST_UNSUPPORTED(".short 0xf817,0xf00f  @pld	[r7, pc]")
+
+	TEST_GROUP("Data-processing (register)")
+
+#define SHIFTS32(op)					\
+	TEST_RR(op"	r0,  r",1, VAL1,", r",2, 3, "")	\
+	TEST_RR(op"	r14, r",12,VAL2,", r",11,10,"")
+
+	SHIFTS32("lsl")
+	SHIFTS32("lsls")
+	SHIFTS32("lsr")
+	SHIFTS32("lsrs")
+	SHIFTS32("asr")
+	SHIFTS32("asrs")
+	SHIFTS32("ror")
+	SHIFTS32("rors")
+
+	TEST_UNSUPPORTED(".short 0xfa01,0xff02	@ lsl	pc, r1, r2")
+	TEST_UNSUPPORTED(".short 0xfa01,0xfd02	@ lsl	sp, r1, r2")
+	TEST_UNSUPPORTED(".short 0xfa0f,0xf002	@ lsl	r0, pc, r2")
+	TEST_UNSUPPORTED(".short 0xfa0d,0xf002	@ lsl	r0, sp, r2")
+	TEST_UNSUPPORTED(".short 0xfa01,0xf00f	@ lsl	r0, r1, pc")
+	TEST_UNSUPPORTED(".short 0xfa01,0xf00d	@ lsl	r0, r1, sp")
+
+	TEST_RR(    "sxtah	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "sxtah	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "sxth	r8, r",7,  HH1,"")
+
+	TEST_UNSUPPORTED(".short 0xfa0f,0xff87	@ sxth	pc, r7");
+	TEST_UNSUPPORTED(".short 0xfa0f,0xfd87	@ sxth	sp, r7");
+	TEST_UNSUPPORTED(".short 0xfa0f,0xf88f	@ sxth	r8, pc");
+	TEST_UNSUPPORTED(".short 0xfa0f,0xf88d	@ sxth	r8, sp");
+
+	TEST_RR(    "uxtah	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uxtah	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "uxth	r8, r",7,  HH1,"")
+
+	TEST_RR(    "sxtab16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "sxtab16	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "sxtb16	r8, r",7,  HH1,"")
+
+	TEST_RR(    "uxtab16	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uxtab16	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "uxtb16	r8, r",7,  HH1,"")
+
+	TEST_RR(    "sxtab	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "sxtab	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "sxtb	r8, r",7,  HH1,"")
+
+	TEST_RR(    "uxtab	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "uxtab	r14,r",12, HH2,", r",10,HH1,", ror #8")
+	TEST_R(     "uxtb	r8, r",7,  HH1,"")
+
+	TEST_UNSUPPORTED(".short 0xfa60,0x00f0")
+	TEST_UNSUPPORTED(".short 0xfa7f,0xffff")
+
+#define PARALLEL_ADD_SUB(op)					\
+	TEST_RR(  op"add16	r0, r",0,  HH1,", r",1, HH2,"")	\
+	TEST_RR(  op"add16	r14, r",12,HH2,", r",10,HH1,"")	\
+	TEST_RR(  op"asx	r0, r",0,  HH1,", r",1, HH2,"")	\
+	TEST_RR(  op"asx	r14, r",12,HH2,", r",10,HH1,"")	\
+	TEST_RR(  op"sax	r0, r",0,  HH1,", r",1, HH2,"")	\
+	TEST_RR(  op"sax	r14, r",12,HH2,", r",10,HH1,"")	\
+	TEST_RR(  op"sub16	r0, r",0,  HH1,", r",1, HH2,"")	\
+	TEST_RR(  op"sub16	r14, r",12,HH2,", r",10,HH1,"")	\
+	TEST_RR(  op"add8	r0, r",0,  HH1,", r",1, HH2,"")	\
+	TEST_RR(  op"add8	r14, r",12,HH2,", r",10,HH1,"")	\
+	TEST_RR(  op"sub8	r0, r",0,  HH1,", r",1, HH2,"")	\
+	TEST_RR(  op"sub8	r14, r",12,HH2,", r",10,HH1,"")
+
+	TEST_GROUP("Parallel addition and subtraction, signed")
+
+	PARALLEL_ADD_SUB("s")
+	PARALLEL_ADD_SUB("q")
+	PARALLEL_ADD_SUB("sh")
+
+	TEST_GROUP("Parallel addition and subtraction, unsigned")
+
+	PARALLEL_ADD_SUB("u")
+	PARALLEL_ADD_SUB("uq")
+	PARALLEL_ADD_SUB("uh")
+
+	TEST_GROUP("Miscellaneous operations")
+
+	TEST_RR("qadd	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR("qadd	lr, r",9, VAL2,", r",8, VAL1,"")
+	TEST_RR("qsub	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR("qsub	lr, r",9, VAL2,", r",8, VAL1,"")
+	TEST_RR("qdadd	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR("qdadd	lr, r",9, VAL2,", r",8, VAL1,"")
+	TEST_RR("qdsub	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR("qdsub	lr, r",9, VAL2,", r",8, VAL1,"")
+
+	TEST_R("rev.w	r0, r",0,   VAL1,"")
+	TEST_R("rev	r14, r",12, VAL2,"")
+	TEST_R("rev16.w	r0, r",0,   VAL1,"")
+	TEST_R("rev16	r14, r",12, VAL2,"")
+	TEST_R("rbit	r0, r",0,   VAL1,"")
+	TEST_R("rbit	r14, r",12, VAL2,"")
+	TEST_R("revsh.w	r0, r",0,   VAL1,"")
+	TEST_R("revsh	r14, r",12, VAL2,"")
+
+	TEST_UNSUPPORTED(".short 0xfa9c,0xff8c	@ rev	pc, r12");
+	TEST_UNSUPPORTED(".short 0xfa9c,0xfd8c	@ rev	sp, r12");
+	TEST_UNSUPPORTED(".short 0xfa9f,0xfe8f	@ rev	r14, pc");
+	TEST_UNSUPPORTED(".short 0xfa9d,0xfe8d	@ rev	r14, sp");
+
+	TEST_RR("sel	r0, r",0,  VAL1,", r",1, VAL2,"")
+	TEST_RR("sel	r14, r",12,VAL1,", r",10, VAL2,"")
+
+	TEST_R("clz	r0, r",0, 0x0,"")
+	TEST_R("clz	r7, r",14,0x1,"")
+	TEST_R("clz	lr, r",7, 0xffffffff,"")
+
+	TEST_UNSUPPORTED(".short 0xfa80,0xf030") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xfaff,0xff7f") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xfab0,0xf000") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xfaff,0xff7f") /* Unallocated space */
+
+	TEST_GROUP("Multiply, multiply accumulate, and absolute difference operations")
+
+	TEST_RR(    "mul	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "mul	r7, r",8, VAL2,", r",9, VAL2,"")
+	TEST_UNSUPPORTED(".short 0xfb08,0xff09	@ mul	pc, r8, r9")
+	TEST_UNSUPPORTED(".short 0xfb08,0xfd09	@ mul	sp, r8, r9")
+	TEST_UNSUPPORTED(".short 0xfb0f,0xf709	@ mul	r7, pc, r9")
+	TEST_UNSUPPORTED(".short 0xfb0d,0xf709	@ mul	r7, sp, r9")
+	TEST_UNSUPPORTED(".short 0xfb08,0xf70f	@ mul	r7, r8, pc")
+	TEST_UNSUPPORTED(".short 0xfb08,0xf70d	@ mul	r7, r8, sp")
+
+	TEST_RRR(   "mla	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(   "mla	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_UNSUPPORTED(".short 0xfb08,0xaf09	@ mla	pc, r8, r9, r10");
+	TEST_UNSUPPORTED(".short 0xfb08,0xad09	@ mla	sp, r8, r9, r10");
+	TEST_UNSUPPORTED(".short 0xfb0f,0xa709	@ mla	r7, pc, r9, r10");
+	TEST_UNSUPPORTED(".short 0xfb0d,0xa709	@ mla	r7, sp, r9, r10");
+	TEST_UNSUPPORTED(".short 0xfb08,0xa70f	@ mla	r7, r8, pc, r10");
+	TEST_UNSUPPORTED(".short 0xfb08,0xa70d	@ mla	r7, r8, sp, r10");
+	TEST_UNSUPPORTED(".short 0xfb08,0xd709	@ mla	r7, r8, r9, sp");
+
+	TEST_RRR(   "mls	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(   "mls	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+
+	TEST_RRR(   "smlabb	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(   "smlabb	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RRR(   "smlatb	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(   "smlatb	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RRR(   "smlabt	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(   "smlabt	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RRR(   "smlatt	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(   "smlatt	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RR(    "smulbb	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smulbb	r7, r",8, VAL3,", r",9, VAL1,"")
+	TEST_RR(    "smultb	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smultb	r7, r",8, VAL3,", r",9, VAL1,"")
+	TEST_RR(    "smulbt	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smulbt	r7, r",8, VAL3,", r",9, VAL1,"")
+	TEST_RR(    "smultt	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smultt	r7, r",8, VAL3,", r",9, VAL1,"")
+
+	TEST_RRR(   "smlad	r0, r",0,  HH1,", r",1, HH2,", r",2, VAL1,"")
+	TEST_RRR(   "smlad	r14, r",12,HH2,", r",10,HH1,", r",8, VAL2,"")
+	TEST_RRR(   "smladx	r0, r",0,  HH1,", r",1, HH2,", r",2, VAL1,"")
+	TEST_RRR(   "smladx	r14, r",12,HH2,", r",10,HH1,", r",8, VAL2,"")
+	TEST_RR(    "smuad	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "smuad	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_RR(    "smuadx	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "smuadx	r14, r",12,HH2,", r",10,HH1,"")
+
+	TEST_RRR(   "smlawb	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(   "smlawb	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RRR(   "smlawt	r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
+	TEST_RRR(   "smlawt	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
+	TEST_RR(    "smulwb	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smulwb	r7, r",8, VAL3,", r",9, VAL1,"")
+	TEST_RR(    "smulwt	r0, r",1, VAL1,", r",2, VAL2,"")
+	TEST_RR(    "smulwt	r7, r",8, VAL3,", r",9, VAL1,"")
+
+	TEST_RRR(   "smlsd	r0, r",0,  HH1,", r",1, HH2,", r",2, VAL1,"")
+	TEST_RRR(   "smlsd	r14, r",12,HH2,", r",10,HH1,", r",8, VAL2,"")
+	TEST_RRR(   "smlsdx	r0, r",0,  HH1,", r",1, HH2,", r",2, VAL1,"")
+	TEST_RRR(   "smlsdx	r14, r",12,HH2,", r",10,HH1,", r",8, VAL2,"")
+	TEST_RR(    "smusd	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "smusd	r14, r",12,HH2,", r",10,HH1,"")
+	TEST_RR(    "smusdx	r0, r",0,  HH1,", r",1, HH2,"")
+	TEST_RR(    "smusdx	r14, r",12,HH2,", r",10,HH1,"")
+
+	TEST_RRR(   "smmla	r0, r",0,  VAL1,", r",1, VAL2,", r",2, VAL1,"")
+	TEST_RRR(   "smmla	r14, r",12,VAL2,", r",10,VAL1,", r",8, VAL2,"")
+	TEST_RRR(   "smmlar	r0, r",0,  VAL1,", r",1, VAL2,", r",2, VAL1,"")
+	TEST_RRR(   "smmlar	r14, r",12,VAL2,", r",10,VAL1,", r",8, VAL2,"")
+	TEST_RR(    "smmul	r0, r",0,  VAL1,", r",1, VAL2,"")
+	TEST_RR(    "smmul	r14, r",12,VAL2,", r",10,VAL1,"")
+	TEST_RR(    "smmulr	r0, r",0,  VAL1,", r",1, VAL2,"")
+	TEST_RR(    "smmulr	r14, r",12,VAL2,", r",10,VAL1,"")
+
+	TEST_RRR(   "smmls	r0, r",0,  VAL1,", r",1, VAL2,", r",2, VAL1,"")
+	TEST_RRR(   "smmls	r14, r",12,VAL2,", r",10,VAL1,", r",8, VAL2,"")
+	TEST_RRR(   "smmlsr	r0, r",0,  VAL1,", r",1, VAL2,", r",2, VAL1,"")
+	TEST_RRR(   "smmlsr	r14, r",12,VAL2,", r",10,VAL1,", r",8, VAL2,"")
+
+	TEST_RRR(   "usada8	r0, r",0,  VAL1,", r",1, VAL2,", r",2, VAL3,"")
+	TEST_RRR(   "usada8	r14, r",12,VAL2,", r",10,VAL1,", r",8, VAL3,"")
+	TEST_RR(    "usad8	r0, r",0,  VAL1,", r",1, VAL2,"")
+	TEST_RR(    "usad8	r14, r",12,VAL2,", r",10,VAL1,"")
+
+	TEST_UNSUPPORTED(".short 0xfb00,0xf010") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xfb0f,0xff1f") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xfb70,0xf010") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xfb7f,0xff1f") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xfb70,0x0010") /* Unallocated space */
+	TEST_UNSUPPORTED(".short 0xfb7f,0xff1f") /* Unallocated space */
+
+	TEST_GROUP("Long multiply, long multiply accumulate, and divide")
+
+	TEST_RR(   "smull	r0, r1, r",2, VAL1,", r",3, VAL2,"")
+	TEST_RR(   "smull	r7, r8, r",9, VAL2,", r",10, VAL1,"")
+	TEST_UNSUPPORTED(".short 0xfb89,0xf80a	@ smull	pc, r8, r9, r10");
+	TEST_UNSUPPORTED(".short 0xfb89,0xd80a	@ smull	sp, r8, r9, r10");
+	TEST_UNSUPPORTED(".short 0xfb89,0x7f0a	@ smull	r7, pc, r9, r10");
+	TEST_UNSUPPORTED(".short 0xfb89,0x7d0a	@ smull	r7, sp, r9, r10");
+	TEST_UNSUPPORTED(".short 0xfb8f,0x780a	@ smull	r7, r8, pc, r10");
+	TEST_UNSUPPORTED(".short 0xfb8d,0x780a	@ smull	r7, r8, sp, r10");
+	TEST_UNSUPPORTED(".short 0xfb89,0x780f	@ smull	r7, r8, r9, pc");
+	TEST_UNSUPPORTED(".short 0xfb89,0x780d	@ smull	r7, r8, r9, sp");
+
+	TEST_RR(   "umull	r0, r1, r",2, VAL1,", r",3, VAL2,"")
+	TEST_RR(   "umull	r7, r8, r",9, VAL2,", r",10, VAL1,"")
+
+	TEST_RRRR( "smlal	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR( "smlal	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+
+	TEST_RRRR( "smlalbb	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR( "smlalbb	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRRR( "smlalbt	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR( "smlalbt	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRRR( "smlaltb	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR( "smlaltb	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRRR( "smlaltt	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR( "smlaltt	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+
+	TEST_RRRR( "smlald	r",0, VAL1,", r",1, VAL2, ", r",0, HH1,", r",1, HH2)
+	TEST_RRRR( "smlald	r",11,VAL2,", r",10,VAL1, ", r",9, HH2,", r",8, HH1)
+	TEST_RRRR( "smlaldx	r",0, VAL1,", r",1, VAL2, ", r",0, HH1,", r",1, HH2)
+	TEST_RRRR( "smlaldx	r",11,VAL2,", r",10,VAL1, ", r",9, HH2,", r",8, HH1)
+
+	TEST_RRRR( "smlsld	r",0, VAL1,", r",1, VAL2, ", r",0, HH1,", r",1, HH2)
+	TEST_RRRR( "smlsld	r",11,VAL2,", r",10,VAL1, ", r",9, HH2,", r",8, HH1)
+	TEST_RRRR( "smlsldx	r",0, VAL1,", r",1, VAL2, ", r",0, HH1,", r",1, HH2)
+	TEST_RRRR( "smlsldx	r",11,VAL2,", r",10,VAL1, ", r",9, HH2,", r",8, HH1)
+
+	TEST_RRRR( "umlal	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR( "umlal	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+	TEST_RRRR( "umaal	r",0, VAL1,", r",1, VAL2,", r",2, VAL3,", r",3, VAL4)
+	TEST_RRRR( "umaal	r",8, VAL4,", r",9, VAL1,", r",10,VAL2,", r",11,VAL3)
+
+	TEST_GROUP("Coprocessor instructions")
+
+	TEST_UNSUPPORTED(".short 0xfc00,0x0000")
+	TEST_UNSUPPORTED(".short 0xffff,0xffff")
+
+	TEST_GROUP("Testing instructions in IT blocks")
+
+	TEST_ITBLOCK("sub.w	r0, r0")
+
+	verbose("\n");
+}
+
diff --git a/arch/arm/kernel/kprobes-test.c b/arch/arm/kernel/kprobes-test.c
new file mode 100644
index 0000000..e17cdd6
--- /dev/null
+++ b/arch/arm/kernel/kprobes-test.c
@@ -0,0 +1,1748 @@
+/*
+ * arch/arm/kernel/kprobes-test.c
+ *
+ * Copyright (C) 2011 Jon Medhurst <tixy@yxit.co.uk>.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * This file contains test code for ARM kprobes.
+ *
+ * The top level function run_all_tests() executes tests for all of the
+ * supported instruction sets: ARM, 16-bit Thumb, and 32-bit Thumb. These tests
+ * fall into two categories; run_api_tests() checks basic functionality of the
+ * kprobes API, and run_test_cases() is a comprehensive test for kprobes
+ * instruction decoding and simulation.
+ *
+ * run_test_cases() first checks the kprobes decoding table for self consistency
+ * (using table_test()) then executes a series of test cases for each of the CPU
+ * instruction forms. coverage_start() and coverage_end() are used to verify
+ * that these test cases cover all of the possible combinations of instructions
+ * described by the kprobes decoding tables.
+ *
+ * The individual test cases are in kprobes-test-arm.c and kprobes-test-thumb.c
+ * which use the macros defined in kprobes-test.h. The rest of this
+ * documentation will describe the operation of the framework used by these
+ * test cases.
+ */
+
+/*
+ * TESTING METHODOLOGY
+ * -------------------
+ *
+ * The methodology used to test an ARM instruction 'test_insn' is to use
+ * inline assembler like:
+ *
+ * test_before: nop
+ * test_case:	test_insn
+ * test_after:	nop
+ *
+ * When the test case is run a kprobe is placed of each nop. The
+ * post-handler of the test_before probe is used to modify the saved CPU
+ * register context to that which we require for the test case. The
+ * pre-handler of the of the test_after probe saves a copy of the CPU
+ * register context. In this way we can execute test_insn with a specific
+ * register context and see the results afterwards.
+ *
+ * To actually test the kprobes instruction emulation we perform the above
+ * step a second time but with an additional kprobe on the test_case
+ * instruction itself. If the emulation is accurate then the results seen
+ * by the test_after probe will be identical to the first run which didn't
+ * have a probe on test_case.
+ *
+ * Each test case is run several times with a variety of variations in the
+ * flags value of stored in CPSR, and for Thumb code, different ITState.
+ *
+ * For instructions which can modify PC, a second test_after probe is used
+ * like this:
+ *
+ * test_before: nop
+ * test_case:	test_insn
+ * test_after:	nop
+ *		b test_done
+ * test_after2: nop
+ * test_done:
+ *
+ * The test case is constructed such that test_insn branches to
+ * test_after2, or, if testing a conditional instruction, it may just
+ * continue to test_after. The probes inserted at both locations let us
+ * determine which happened. A similar approach is used for testing
+ * backwards branches...
+ *
+ *		b test_before
+ *		b test_done  @ helps to cope with off by 1 branches
+ * test_after2: nop
+ *		b test_done
+ * test_before: nop
+ * test_case:	test_insn
+ * test_after:	nop
+ * test_done:
+ *
+ * The macros used to generate the assembler instructions describe above
+ * are TEST_INSTRUCTION, TEST_BRANCH_F (branch forwards) and TEST_BRANCH_B
+ * (branch backwards). In these, the local variables numbered 1, 50, 2 and
+ * 99 represent: test_before, test_case, test_after2 and test_done.
+ *
+ * FRAMEWORK
+ * ---------
+ *
+ * Each test case is wrapped between the pair of macros TESTCASE_START and
+ * TESTCASE_END. As well as performing the inline assembler boilerplate,
+ * these call out to the kprobes_test_case_start() and
+ * kprobes_test_case_end() functions which drive the execution of the test
+ * case. The specific arguments to use for each test case are stored as
+ * inline data constructed using the various TEST_ARG_* macros. Putting
+ * this all together, a simple test case may look like:
+ *
+ *	TESTCASE_START("Testing mov r0, r7")
+ *	TEST_ARG_REG(7, 0x12345678) // Set r7=0x12345678
+ *	TEST_ARG_END("")
+ *	TEST_INSTRUCTION("mov r0, r7")
+ *	TESTCASE_END
+ *
+ * Note, in practice the single convenience macro TEST_R would be used for this
+ * instead.
+ *
+ * The above would expand to assembler looking something like:
+ *
+ *	@ TESTCASE_START
+ *	bl	__kprobes_test_case_start
+ *	@ start of inline data...
+ *	.ascii "mov r0, r7"	@ text title for test case
+ *	.byte	0
+ *	.align	2
+ *
+ *	@ TEST_ARG_REG
+ *	.byte	ARG_TYPE_REG
+ *	.byte	7
+ *	.short	0
+ *	.word	0x1234567
+ *
+ *	@ TEST_ARG_END
+ *	.byte	ARG_TYPE_END
+ *	.byte	TEST_ISA	@ flags, including ISA being tested
+ *	.short	50f-0f		@ offset of 'test_before'
+ *	.short	2f-0f		@ offset of 'test_after2' (if relevent)
+ *	.short	99f-0f		@ offset of 'test_done'
+ *	@ start of test case code...
+ *	0:
+ *	.code	TEST_ISA	@ switch to ISA being tested
+ *
+ *	@ TEST_INSTRUCTION
+ *	50:	nop		@ location for 'test_before' probe
+ *	1:	mov r0, r7	@ the test case instruction 'test_insn'
+ *		nop		@ location for 'test_after' probe
+ *
+ *	// TESTCASE_END
+ *	2:
+ *	99:	bl __kprobes_test_case_end_##TEST_ISA
+ *	.code	NONMAL_ISA
+ *
+ * When the above is execute the following happens...
+ *
+ * __kprobes_test_case_start() is an assembler wrapper which sets up space
+ * for a stack buffer and calls the C function kprobes_test_case_start().
+ * This C function will do some initial processing of the inline data and
+ * setup some global state. It then inserts the test_before and test_after
+ * kprobes and returns a value which causes the assembler wrapper to jump
+ * to the start of the test case code, (local label '0').
+ *
+ * When the test case code executes, the test_before probe will be hit and
+ * test_before_post_handler will call setup_test_context(). This fills the
+ * stack buffer and CPU registers with a test pattern and then processes
+ * the test case arguments. In our example there is one TEST_ARG_REG which
+ * indicates that R7 should be loaded with the value 0x12345678.
+ *
+ * When the test_before probe ends, the test case continues and executes
+ * the "mov r0, r7" instruction. It then hits the test_after probe and the
+ * pre-handler for this (test_after_pre_handler) will save a copy of the
+ * CPU register context. This should now have R0 holding the same value as
+ * R7.
+ *
+ * Finally we get to the call to __kprobes_test_case_end_{32,16}. This is
+ * an assembler wrapper which switches back to the ISA used by the test
+ * code and calls the C function kprobes_test_case_end().
+ *
+ * For each run through the test case, test_case_run_count is incremented
+ * by one. For even runs, kprobes_test_case_end() saves a copy of the
+ * register and stack buffer contents from the test case just run. It then
+ * inserts a kprobe on the test case instruction 'test_insn' and returns a
+ * value to cause the test case code to be re-run.
+ *
+ * For odd numbered runs, kprobes_test_case_end() compares the register and
+ * stack buffer contents to those that were saved on the previous even
+ * numbered run (the one without the kprobe on test_insn). These should be
+ * the same if the kprobe instruction simulation routine is correct.
+ *
+ * The pair of test case runs is repeated with different combinations of
+ * flag values in CPSR and, for Thumb, different ITState. This is
+ * controlled by test_context_cpsr().
+ *
+ * BUILDING TEST CASES
+ * -------------------
+ *
+ *
+ * As an aid to building test cases, the stack buffer is initialised with
+ * some special values:
+ *
+ *   [SP+13*4]	Contains SP+120. This can be used to test instructions
+ *		which load a value into SP.
+ *
+ *   [SP+15*4]	When testing branching instructions using TEST_BRANCH_{F,B},
+ *		this holds the target address of the branch, 'test_after2'.
+ *		This can be used to test instructions which load a PC value
+ *		from memory.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/kprobes.h>
+
+#include "kprobes.h"
+#include "kprobes-test.h"
+
+
+#define BENCHMARKING	1
+
+
+/*
+ * Test basic API
+ */
+
+static bool test_regs_ok;
+static int test_func_instance;
+static int pre_handler_called;
+static int post_handler_called;
+static int jprobe_func_called;
+static int kretprobe_handler_called;
+
+#define FUNC_ARG1 0x12345678
+#define FUNC_ARG2 0xabcdef
+
+
+#ifndef CONFIG_THUMB2_KERNEL
+
+long arm_func(long r0, long r1);
+
+static void __used __naked __arm_kprobes_test_func(void)
+{
+	__asm__ __volatile__ (
+		".arm					\n\t"
+		".type arm_func, %%function		\n\t"
+		"arm_func:				\n\t"
+		"adds	r0, r0, r1			\n\t"
+		"bx	lr				\n\t"
+		".code "NORMAL_ISA	 /* Back to Thumb if necessary */
+		: : : "r0", "r1", "cc"
+	);
+}
+
+#else /* CONFIG_THUMB2_KERNEL */
+
+long thumb16_func(long r0, long r1);
+long thumb32even_func(long r0, long r1);
+long thumb32odd_func(long r0, long r1);
+
+static void __used __naked __thumb_kprobes_test_funcs(void)
+{
+	__asm__ __volatile__ (
+		".type thumb16_func, %%function		\n\t"
+		"thumb16_func:				\n\t"
+		"adds.n	r0, r0, r1			\n\t"
+		"bx	lr				\n\t"
+
+		".align					\n\t"
+		".type thumb32even_func, %%function	\n\t"
+		"thumb32even_func:			\n\t"
+		"adds.w	r0, r0, r1			\n\t"
+		"bx	lr				\n\t"
+
+		".align					\n\t"
+		"nop.n					\n\t"
+		".type thumb32odd_func, %%function	\n\t"
+		"thumb32odd_func:			\n\t"
+		"adds.w	r0, r0, r1			\n\t"
+		"bx	lr				\n\t"
+
+		: : : "r0", "r1", "cc"
+	);
+}
+
+#endif /* CONFIG_THUMB2_KERNEL */
+
+
+static int call_test_func(long (*func)(long, long), bool check_test_regs)
+{
+	long ret;
+
+	++test_func_instance;
+	test_regs_ok = false;
+
+	ret = (*func)(FUNC_ARG1, FUNC_ARG2);
+	if (ret != FUNC_ARG1 + FUNC_ARG2) {
+		pr_err("FAIL: call_test_func: func returned %lx\n", ret);
+		return false;
+	}
+
+	if (check_test_regs && !test_regs_ok) {
+		pr_err("FAIL: test regs not OK\n");
+		return false;
+	}
+
+	return true;
+}
+
+static int __kprobes pre_handler(struct kprobe *p, struct pt_regs *regs)
+{
+	pre_handler_called = test_func_instance;
+	if (regs->ARM_r0 == FUNC_ARG1 && regs->ARM_r1 == FUNC_ARG2)
+		test_regs_ok = true;
+	return 0;
+}
+
+static void __kprobes post_handler(struct kprobe *p, struct pt_regs *regs,
+				unsigned long flags)
+{
+	post_handler_called = test_func_instance;
+	if (regs->ARM_r0 != FUNC_ARG1 + FUNC_ARG2 || regs->ARM_r1 != FUNC_ARG2)
+		test_regs_ok = false;
+}
+
+static struct kprobe the_kprobe = {
+	.addr		= 0,
+	.pre_handler	= pre_handler,
+	.post_handler	= post_handler
+};
+
+static int test_kprobe(long (*func)(long, long))
+{
+	int ret;
+
+	the_kprobe.addr = (kprobe_opcode_t *)func;
+	ret = register_kprobe(&the_kprobe);
+	if (ret < 0) {
+		pr_err("FAIL: register_kprobe failed with %d\n", ret);
+		return ret;
+	}
+
+	ret = call_test_func(func, true);
+
+	unregister_kprobe(&the_kprobe);
+	the_kprobe.flags = 0; /* Clear disable flag to allow reuse */
+
+	if (!ret)
+		return -EINVAL;
+	if (pre_handler_called != test_func_instance) {
+		pr_err("FAIL: kprobe pre_handler not called\n");
+		return -EINVAL;
+	}
+	if (post_handler_called != test_func_instance) {
+		pr_err("FAIL: kprobe post_handler not called\n");
+		return -EINVAL;
+	}
+	if (!call_test_func(func, false))
+		return -EINVAL;
+	if (pre_handler_called == test_func_instance ||
+				post_handler_called == test_func_instance) {
+		pr_err("FAIL: probe called after unregistering\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void __kprobes jprobe_func(long r0, long r1)
+{
+	jprobe_func_called = test_func_instance;
+	if (r0 == FUNC_ARG1 && r1 == FUNC_ARG2)
+		test_regs_ok = true;
+	jprobe_return();
+}
+
+static struct jprobe the_jprobe = {
+	.entry		= jprobe_func,
+};
+
+static int test_jprobe(long (*func)(long, long))
+{
+	int ret;
+
+	the_jprobe.kp.addr = (kprobe_opcode_t *)func;
+	ret = register_jprobe(&the_jprobe);
+	if (ret < 0) {
+		pr_err("FAIL: register_jprobe failed with %d\n", ret);
+		return ret;
+	}
+
+	ret = call_test_func(func, true);
+
+	unregister_jprobe(&the_jprobe);
+	the_jprobe.kp.flags = 0; /* Clear disable flag to allow reuse */
+
+	if (!ret)
+		return -EINVAL;
+	if (jprobe_func_called != test_func_instance) {
+		pr_err("FAIL: jprobe handler function not called\n");
+		return -EINVAL;
+	}
+	if (!call_test_func(func, false))
+		return -EINVAL;
+	if (jprobe_func_called == test_func_instance) {
+		pr_err("FAIL: probe called after unregistering\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int __kprobes
+kretprobe_handler(struct kretprobe_instance *ri, struct pt_regs *regs)
+{
+	kretprobe_handler_called = test_func_instance;
+	if (regs_return_value(regs) == FUNC_ARG1 + FUNC_ARG2)
+		test_regs_ok = true;
+	return 0;
+}
+
+static struct kretprobe the_kretprobe = {
+	.handler	= kretprobe_handler,
+};
+
+static int test_kretprobe(long (*func)(long, long))
+{
+	int ret;
+
+	the_kretprobe.kp.addr = (kprobe_opcode_t *)func;
+	ret = register_kretprobe(&the_kretprobe);
+	if (ret < 0) {
+		pr_err("FAIL: register_kretprobe failed with %d\n", ret);
+		return ret;
+	}
+
+	ret = call_test_func(func, true);
+
+	unregister_kretprobe(&the_kretprobe);
+	the_kretprobe.kp.flags = 0; /* Clear disable flag to allow reuse */
+
+	if (!ret)
+		return -EINVAL;
+	if (kretprobe_handler_called != test_func_instance) {
+		pr_err("FAIL: kretprobe handler not called\n");
+		return -EINVAL;
+	}
+	if (!call_test_func(func, false))
+		return -EINVAL;
+	if (jprobe_func_called == test_func_instance) {
+		pr_err("FAIL: kretprobe called after unregistering\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int run_api_tests(long (*func)(long, long))
+{
+	int ret;
+
+	pr_info("    kprobe\n");
+	ret = test_kprobe(func);
+	if (ret < 0)
+		return ret;
+
+	pr_info("    jprobe\n");
+	ret = test_jprobe(func);
+	if (ret < 0)
+		return ret;
+
+	pr_info("    kretprobe\n");
+	ret = test_kretprobe(func);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+
+/*
+ * Benchmarking
+ */
+
+#if BENCHMARKING
+
+static void __naked benchmark_nop(void)
+{
+	__asm__ __volatile__ (
+		"nop		\n\t"
+		"bx	lr"
+	);
+}
+
+#ifdef CONFIG_THUMB2_KERNEL
+#define wide ".w"
+#else
+#define wide
+#endif
+
+static void __naked benchmark_pushpop1(void)
+{
+	__asm__ __volatile__ (
+		"stmdb"wide"	sp!, {r3-r11,lr}  \n\t"
+		"ldmia"wide"	sp!, {r3-r11,pc}"
+	);
+}
+
+static void __naked benchmark_pushpop2(void)
+{
+	__asm__ __volatile__ (
+		"stmdb"wide"	sp!, {r0-r8,lr}  \n\t"
+		"ldmia"wide"	sp!, {r0-r8,pc}"
+	);
+}
+
+static void __naked benchmark_pushpop3(void)
+{
+	__asm__ __volatile__ (
+		"stmdb"wide"	sp!, {r4,lr}  \n\t"
+		"ldmia"wide"	sp!, {r4,pc}"
+	);
+}
+
+static void __naked benchmark_pushpop4(void)
+{
+	__asm__ __volatile__ (
+		"stmdb"wide"	sp!, {r0,lr}  \n\t"
+		"ldmia"wide"	sp!, {r0,pc}"
+	);
+}
+
+
+#ifdef CONFIG_THUMB2_KERNEL
+
+static void __naked benchmark_pushpop_thumb(void)
+{
+	__asm__ __volatile__ (
+		"push.n	{r0-r7,lr}  \n\t"
+		"pop.n	{r0-r7,pc}"
+	);
+}
+
+#endif
+
+static int __kprobes
+benchmark_pre_handler(struct kprobe *p, struct pt_regs *regs)
+{
+	return 0;
+}
+
+static int benchmark(void(*fn)(void))
+{
+	unsigned n, i, t, t0;
+
+	for (n = 1000; ; n *= 2) {
+		t0 = sched_clock();
+		for (i = n; i > 0; --i)
+			fn();
+		t = sched_clock() - t0;
+		if (t >= 250000000)
+			break; /* Stop once we took more than 0.25 seconds */
+	}
+	return t / n; /* Time for one iteration in nanoseconds */
+};
+
+static int kprobe_benchmark(void(*fn)(void), unsigned offset)
+{
+	struct kprobe k = {
+		.addr		= (kprobe_opcode_t *)((uintptr_t)fn + offset),
+		.pre_handler	= benchmark_pre_handler,
+	};
+
+	int ret = register_kprobe(&k);
+	if (ret < 0) {
+		pr_err("FAIL: register_kprobe failed with %d\n", ret);
+		return ret;
+	}
+
+	ret = benchmark(fn);
+
+	unregister_kprobe(&k);
+	return ret;
+};
+
+struct benchmarks {
+	void		(*fn)(void);
+	unsigned	offset;
+	const char	*title;
+};
+
+static int run_benchmarks(void)
+{
+	int ret;
+	struct benchmarks list[] = {
+		{&benchmark_nop, 0, "nop"},
+		/*
+		 * benchmark_pushpop{1,3} will have the optimised
+		 * instruction emulation, whilst benchmark_pushpop{2,4} will
+		 * be the equivalent unoptimised instructions.
+		 */
+		{&benchmark_pushpop1, 0, "stmdb	sp!, {r3-r11,lr}"},
+		{&benchmark_pushpop1, 4, "ldmia	sp!, {r3-r11,pc}"},
+		{&benchmark_pushpop2, 0, "stmdb	sp!, {r0-r8,lr}"},
+		{&benchmark_pushpop2, 4, "ldmia	sp!, {r0-r8,pc}"},
+		{&benchmark_pushpop3, 0, "stmdb	sp!, {r4,lr}"},
+		{&benchmark_pushpop3, 4, "ldmia	sp!, {r4,pc}"},
+		{&benchmark_pushpop4, 0, "stmdb	sp!, {r0,lr}"},
+		{&benchmark_pushpop4, 4, "ldmia	sp!, {r0,pc}"},
+#ifdef CONFIG_THUMB2_KERNEL
+		{&benchmark_pushpop_thumb, 0, "push.n	{r0-r7,lr}"},
+		{&benchmark_pushpop_thumb, 2, "pop.n	{r0-r7,pc}"},
+#endif
+		{0}
+	};
+
+	struct benchmarks *b;
+	for (b = list; b->fn; ++b) {
+		ret = kprobe_benchmark(b->fn, b->offset);
+		if (ret < 0)
+			return ret;
+		pr_info("    %dns for kprobe %s\n", ret, b->title);
+	}
+
+	pr_info("\n");
+	return 0;
+}
+
+#endif /* BENCHMARKING */
+
+
+/*
+ * Decoding table self-consistency tests
+ */
+
+static const int decode_struct_sizes[NUM_DECODE_TYPES] = {
+	[DECODE_TYPE_TABLE]	= sizeof(struct decode_table),
+	[DECODE_TYPE_CUSTOM]	= sizeof(struct decode_custom),
+	[DECODE_TYPE_SIMULATE]	= sizeof(struct decode_simulate),
+	[DECODE_TYPE_EMULATE]	= sizeof(struct decode_emulate),
+	[DECODE_TYPE_OR]	= sizeof(struct decode_or),
+	[DECODE_TYPE_REJECT]	= sizeof(struct decode_reject)
+};
+
+static int table_iter(const union decode_item *table,
+			int (*fn)(const struct decode_header *, void *),
+			void *args)
+{
+	const struct decode_header *h = (struct decode_header *)table;
+	int result;
+
+	for (;;) {
+		enum decode_type type = h->type_regs.bits & DECODE_TYPE_MASK;
+
+		if (type == DECODE_TYPE_END)
+			return 0;
+
+		result = fn(h, args);
+		if (result)
+			return result;
+
+		h = (struct decode_header *)
+			((uintptr_t)h + decode_struct_sizes[type]);
+
+	}
+}
+
+static int table_test_fail(const struct decode_header *h, const char* message)
+{
+
+	pr_err("FAIL: kprobes test failure \"%s\" (mask %08x, value %08x)\n",
+					message, h->mask.bits, h->value.bits);
+	return -EINVAL;
+}
+
+struct table_test_args {
+	const union decode_item *root_table;
+	u32			parent_mask;
+	u32			parent_value;
+};
+
+static int table_test_fn(const struct decode_header *h, void *args)
+{
+	struct table_test_args *a = (struct table_test_args *)args;
+	enum decode_type type = h->type_regs.bits & DECODE_TYPE_MASK;
+
+	if (h->value.bits & ~h->mask.bits)
+		return table_test_fail(h, "Match value has bits not in mask");
+
+	if ((h->mask.bits & a->parent_mask) != a->parent_mask)
+		return table_test_fail(h, "Mask has bits not in parent mask");
+
+	if ((h->value.bits ^ a->parent_value) & a->parent_mask)
+		return table_test_fail(h, "Value is inconsistent with parent");
+
+	if (type == DECODE_TYPE_TABLE) {
+		struct decode_table *d = (struct decode_table *)h;
+		struct table_test_args args2 = *a;
+		args2.parent_mask = h->mask.bits;
+		args2.parent_value = h->value.bits;
+		return table_iter(d->table.table, table_test_fn, &args2);
+	}
+
+	return 0;
+}
+
+static int table_test(const union decode_item *table)
+{
+	struct table_test_args args = {
+		.root_table	= table,
+		.parent_mask	= 0,
+		.parent_value	= 0
+	};
+	return table_iter(args.root_table, table_test_fn, &args);
+}
+
+
+/*
+ * Decoding table test coverage analysis
+ *
+ * coverage_start() builds a coverage_table which contains a list of
+ * coverage_entry's to match each entry in the specified kprobes instruction
+ * decoding table.
+ *
+ * When test cases are run, coverage_add() is called to process each case.
+ * This looks up the corresponding entry in the coverage_table and sets it as
+ * being matched, as well as clearing the regs flag appropriate for the test.
+ *
+ * After all test cases have been run, coverage_end() is called to check that
+ * all entries in coverage_table have been matched and that all regs flags are
+ * cleared. I.e. that all possible combinations of instructions described by
+ * the kprobes decoding tables have had a test case executed for them.
+ */
+
+bool coverage_fail;
+
+#define MAX_COVERAGE_ENTRIES 256
+
+struct coverage_entry {
+	const struct decode_header	*header;
+	unsigned			regs;
+	unsigned			nesting;
+	char				matched;
+};
+
+struct coverage_table {
+	struct coverage_entry	*base;
+	unsigned		num_entries;
+	unsigned		nesting;
+};
+
+struct coverage_table coverage;
+
+#define COVERAGE_ANY_REG	(1<<0)
+#define COVERAGE_SP		(1<<1)
+#define COVERAGE_PC		(1<<2)
+#define COVERAGE_PCWB		(1<<3)
+
+static const char coverage_register_lookup[16] = {
+	[REG_TYPE_ANY]		= COVERAGE_ANY_REG | COVERAGE_SP | COVERAGE_PC,
+	[REG_TYPE_SAMEAS16]	= COVERAGE_ANY_REG,
+	[REG_TYPE_SP]		= COVERAGE_SP,
+	[REG_TYPE_PC]		= COVERAGE_PC,
+	[REG_TYPE_NOSP]		= COVERAGE_ANY_REG | COVERAGE_SP,
+	[REG_TYPE_NOSPPC]	= COVERAGE_ANY_REG | COVERAGE_SP | COVERAGE_PC,
+	[REG_TYPE_NOPC]		= COVERAGE_ANY_REG | COVERAGE_PC,
+	[REG_TYPE_NOPCWB]	= COVERAGE_ANY_REG | COVERAGE_PC | COVERAGE_PCWB,
+	[REG_TYPE_NOPCX]	= COVERAGE_ANY_REG,
+	[REG_TYPE_NOSPPCX]	= COVERAGE_ANY_REG | COVERAGE_SP,
+};
+
+unsigned coverage_start_registers(const struct decode_header *h)
+{
+	unsigned regs = 0;
+	int i;
+	for (i = 0; i < 20; i += 4) {
+		int r = (h->type_regs.bits >> (DECODE_TYPE_BITS + i)) & 0xf;
+		regs |= coverage_register_lookup[r] << i;
+	}
+	return regs;
+}
+
+static int coverage_start_fn(const struct decode_header *h, void *args)
+{
+	struct coverage_table *coverage = (struct coverage_table *)args;
+	enum decode_type type = h->type_regs.bits & DECODE_TYPE_MASK;
+	struct coverage_entry *entry = coverage->base + coverage->num_entries;
+
+	if (coverage->num_entries == MAX_COVERAGE_ENTRIES - 1) {
+		pr_err("FAIL: Out of space for test coverage data");
+		return -ENOMEM;
+	}
+
+	++coverage->num_entries;
+
+	entry->header = h;
+	entry->regs = coverage_start_registers(h);
+	entry->nesting = coverage->nesting;
+	entry->matched = false;
+
+	if (type == DECODE_TYPE_TABLE) {
+		struct decode_table *d = (struct decode_table *)h;
+		int ret;
+		++coverage->nesting;
+		ret = table_iter(d->table.table, coverage_start_fn, coverage);
+		--coverage->nesting;
+		return ret;
+	}
+
+	return 0;
+}
+
+static int coverage_start(const union decode_item *table)
+{
+	coverage.base = kmalloc(MAX_COVERAGE_ENTRIES *
+				sizeof(struct coverage_entry), GFP_KERNEL);
+	coverage.num_entries = 0;
+	coverage.nesting = 0;
+	return table_iter(table, coverage_start_fn, &coverage);
+}
+
+static void
+coverage_add_registers(struct coverage_entry *entry, kprobe_opcode_t insn)
+{
+	int regs = entry->header->type_regs.bits >> DECODE_TYPE_BITS;
+	int i;
+	for (i = 0; i < 20; i += 4) {
+		enum decode_reg_type reg_type = (regs >> i) & 0xf;
+		int reg = (insn >> i) & 0xf;
+		int flag;
+
+		if (!reg_type)
+			continue;
+
+		if (reg == 13)
+			flag = COVERAGE_SP;
+		else if (reg == 15)
+			flag = COVERAGE_PC;
+		else
+			flag = COVERAGE_ANY_REG;
+		entry->regs &= ~(flag << i);
+
+		switch (reg_type) {
+
+		case REG_TYPE_NONE:
+		case REG_TYPE_ANY:
+		case REG_TYPE_SAMEAS16:
+			break;
+
+		case REG_TYPE_SP:
+			if (reg != 13)
+				return;
+			break;
+
+		case REG_TYPE_PC:
+			if (reg != 15)
+				return;
+			break;
+
+		case REG_TYPE_NOSP:
+			if (reg == 13)
+				return;
+			break;
+
+		case REG_TYPE_NOSPPC:
+		case REG_TYPE_NOSPPCX:
+			if (reg == 13 || reg == 15)
+				return;
+			break;
+
+		case REG_TYPE_NOPCWB:
+			if (!is_writeback(insn))
+				break;
+			if (reg == 15) {
+				entry->regs &= ~(COVERAGE_PCWB << i);
+				return;
+			}
+			break;
+
+		case REG_TYPE_NOPC:
+		case REG_TYPE_NOPCX:
+			if (reg == 15)
+				return;
+			break;
+		}
+
+	}
+}
+
+static void coverage_add(kprobe_opcode_t insn)
+{
+	struct coverage_entry *entry = coverage.base;
+	struct coverage_entry *end = coverage.base + coverage.num_entries;
+	bool matched = false;
+	unsigned nesting = 0;
+
+	for (; entry < end; ++entry) {
+		const struct decode_header *h = entry->header;
+		enum decode_type type = h->type_regs.bits & DECODE_TYPE_MASK;
+
+		if (entry->nesting > nesting)
+			continue; /* Skip sub-table we didn't match */
+
+		if (entry->nesting < nesting)
+			break; /* End of sub-table we were scanning */
+
+		if (!matched) {
+			if ((insn & h->mask.bits) != h->value.bits)
+				continue;
+			entry->matched = true;
+		}
+
+		switch (type) {
+
+		case DECODE_TYPE_TABLE:
+			++nesting;
+			break;
+
+		case DECODE_TYPE_CUSTOM:
+		case DECODE_TYPE_SIMULATE:
+		case DECODE_TYPE_EMULATE:
+			coverage_add_registers(entry, insn);
+			return;
+
+		case DECODE_TYPE_OR:
+			matched = true;
+			break;
+
+		case DECODE_TYPE_REJECT:
+		default:
+			return;
+		}
+
+	}
+}
+
+static void coverage_end(void)
+{
+	struct coverage_entry *entry = coverage.base;
+	struct coverage_entry *end = coverage.base + coverage.num_entries;
+
+	for (; entry < end; ++entry) {
+		u32 mask = entry->header->mask.bits;
+		u32 value = entry->header->value.bits;
+
+		if (entry->regs) {
+			pr_err("FAIL: Register test coverage missing for %08x %08x (%05x)\n",
+				mask, value, entry->regs);
+			coverage_fail = true;
+		}
+		if (!entry->matched) {
+			pr_err("FAIL: Test coverage entry missing for %08x %08x\n",
+				mask, value);
+			coverage_fail = true;
+		}
+	}
+
+	kfree(coverage.base);
+}
+
+
+/*
+ * Framework for instruction set test cases
+ */
+
+void __naked __kprobes_test_case_start(void)
+{
+	__asm__ __volatile__ (
+		"stmdb	sp!, {r4-r11}				\n\t"
+		"sub	sp, sp, #"__stringify(TEST_MEMORY_SIZE)"\n\t"
+		"bic	r0, lr, #1  @ r0 = inline title string	\n\t"
+		"mov	r1, sp					\n\t"
+		"bl	kprobes_test_case_start			\n\t"
+		"bx	r0					\n\t"
+	);
+}
+
+#ifndef CONFIG_THUMB2_KERNEL
+
+void __naked __kprobes_test_case_end_32(void)
+{
+	__asm__ __volatile__ (
+		"mov	r4, lr					\n\t"
+		"bl	kprobes_test_case_end			\n\t"
+		"cmp	r0, #0					\n\t"
+		"movne	pc, r0					\n\t"
+		"mov	r0, r4					\n\t"
+		"add	sp, sp, #"__stringify(TEST_MEMORY_SIZE)"\n\t"
+		"ldmia	sp!, {r4-r11}				\n\t"
+		"mov	pc, r0					\n\t"
+	);
+}
+
+#else /* CONFIG_THUMB2_KERNEL */
+
+void __naked __kprobes_test_case_end_16(void)
+{
+	__asm__ __volatile__ (
+		"mov	r4, lr					\n\t"
+		"bl	kprobes_test_case_end			\n\t"
+		"cmp	r0, #0					\n\t"
+		"bxne	r0					\n\t"
+		"mov	r0, r4					\n\t"
+		"add	sp, sp, #"__stringify(TEST_MEMORY_SIZE)"\n\t"
+		"ldmia	sp!, {r4-r11}				\n\t"
+		"bx	r0					\n\t"
+	);
+}
+
+void __naked __kprobes_test_case_end_32(void)
+{
+	__asm__ __volatile__ (
+		".arm						\n\t"
+		"orr	lr, lr, #1  @ will return to Thumb code	\n\t"
+		"ldr	pc, 1f					\n\t"
+		"1:						\n\t"
+		".word	__kprobes_test_case_end_16		\n\t"
+	);
+}
+
+#endif
+
+
+int kprobe_test_flags;
+int kprobe_test_cc_position;
+
+static int test_try_count;
+static int test_pass_count;
+static int test_fail_count;
+
+static struct pt_regs initial_regs;
+static struct pt_regs expected_regs;
+static struct pt_regs result_regs;
+
+static u32 expected_memory[TEST_MEMORY_SIZE/sizeof(u32)];
+
+static const char *current_title;
+static struct test_arg *current_args;
+static u32 *current_stack;
+static uintptr_t current_branch_target;
+
+static uintptr_t current_code_start;
+static kprobe_opcode_t current_instruction;
+
+
+#define TEST_CASE_PASSED -1
+#define TEST_CASE_FAILED -2
+
+static int test_case_run_count;
+static bool test_case_is_thumb;
+static int test_instance;
+
+/*
+ * We ignore the state of the imprecise abort disable flag (CPSR.A) because this
+ * can change randomly as the kernel doesn't take care to preserve or initialise
+ * this across context switches. Also, with Security Extentions, the flag may
+ * not be under control of the kernel; for this reason we ignore the state of
+ * the FIQ disable flag CPSR.F as well.
+ */
+#define PSR_IGNORE_BITS (PSR_A_BIT | PSR_F_BIT)
+
+static unsigned long test_check_cc(int cc, unsigned long cpsr)
+{
+	unsigned long temp;
+
+	switch (cc) {
+	case 0x0: /* eq */
+		return cpsr & PSR_Z_BIT;
+
+	case 0x1: /* ne */
+		return (~cpsr) & PSR_Z_BIT;
+
+	case 0x2: /* cs */
+		return cpsr & PSR_C_BIT;
+
+	case 0x3: /* cc */
+		return (~cpsr) & PSR_C_BIT;
+
+	case 0x4: /* mi */
+		return cpsr & PSR_N_BIT;
+
+	case 0x5: /* pl */
+		return (~cpsr) & PSR_N_BIT;
+
+	case 0x6: /* vs */
+		return cpsr & PSR_V_BIT;
+
+	case 0x7: /* vc */
+		return (~cpsr) & PSR_V_BIT;
+
+	case 0x8: /* hi */
+		cpsr &= ~(cpsr >> 1); /* PSR_C_BIT &= ~PSR_Z_BIT */
+		return cpsr & PSR_C_BIT;
+
+	case 0x9: /* ls */
+		cpsr &= ~(cpsr >> 1); /* PSR_C_BIT &= ~PSR_Z_BIT */
+		return (~cpsr) & PSR_C_BIT;
+
+	case 0xa: /* ge */
+		cpsr ^= (cpsr << 3); /* PSR_N_BIT ^= PSR_V_BIT */
+		return (~cpsr) & PSR_N_BIT;
+
+	case 0xb: /* lt */
+		cpsr ^= (cpsr << 3); /* PSR_N_BIT ^= PSR_V_BIT */
+		return cpsr & PSR_N_BIT;
+
+	case 0xc: /* gt */
+		temp = cpsr ^ (cpsr << 3); /* PSR_N_BIT ^= PSR_V_BIT */
+		temp |= (cpsr << 1);	   /* PSR_N_BIT |= PSR_Z_BIT */
+		return (~temp) & PSR_N_BIT;
+
+	case 0xd: /* le */
+		temp = cpsr ^ (cpsr << 3); /* PSR_N_BIT ^= PSR_V_BIT */
+		temp |= (cpsr << 1);	   /* PSR_N_BIT |= PSR_Z_BIT */
+		return temp & PSR_N_BIT;
+
+	case 0xe: /* al */
+	case 0xf: /* unconditional */
+		return true;
+	}
+	BUG();
+	return false;
+}
+
+static int is_last_scenario;
+static int probe_should_run; /* 0 = no, 1 = yes, -1 = unknown */
+static int memory_needs_checking;
+
+static unsigned long test_context_cpsr(int scenario)
+{
+	unsigned long cpsr;
+
+	probe_should_run = 1;
+
+	/* Default case is that we cycle through 16 combinations of flags */
+	cpsr  = (scenario & 0xf) << 28; /* N,Z,C,V flags */
+	cpsr |= (scenario & 0xf) << 16; /* GE flags */
+	cpsr |= (scenario & 0x1) << 27; /* Toggle Q flag */
+
+	if (!test_case_is_thumb) {
+		/* Testing ARM code */
+		probe_should_run = test_check_cc(current_instruction >> 28, cpsr) != 0;
+		if (scenario == 15)
+			is_last_scenario = true;
+
+	} else if (kprobe_test_flags & TEST_FLAG_NO_ITBLOCK) {
+		/* Testing Thumb code without setting ITSTATE */
+		if (kprobe_test_cc_position) {
+			int cc = (current_instruction >> kprobe_test_cc_position) & 0xf;
+			probe_should_run = test_check_cc(cc, cpsr) != 0;
+		}
+
+		if (scenario == 15)
+			is_last_scenario = true;
+
+	} else if (kprobe_test_flags & TEST_FLAG_FULL_ITBLOCK) {
+		/* Testing Thumb code with all combinations of ITSTATE */
+		unsigned x = (scenario >> 4);
+		unsigned cond_base = x % 7; /* ITSTATE<7:5> */
+		unsigned mask = x / 7 + 2;  /* ITSTATE<4:0>, bits reversed */
+
+		if (mask > 0x1f) {
+			/* Finish by testing state from instruction 'itt al' */
+			cond_base = 7;
+			mask = 0x4;
+			if ((scenario & 0xf) == 0xf)
+				is_last_scenario = true;
+		}
+
+		cpsr |= cond_base << 13;	/* ITSTATE<7:5> */
+		cpsr |= (mask & 0x1) << 12;	/* ITSTATE<4> */
+		cpsr |= (mask & 0x2) << 10;	/* ITSTATE<3> */
+		cpsr |= (mask & 0x4) << 8;	/* ITSTATE<2> */
+		cpsr |= (mask & 0x8) << 23;	/* ITSTATE<1> */
+		cpsr |= (mask & 0x10) << 21;	/* ITSTATE<0> */
+
+		probe_should_run = test_check_cc((cpsr >> 12) & 0xf, cpsr) != 0;
+
+	} else {
+		/* Testing Thumb code with several combinations of ITSTATE */
+		switch (scenario) {
+		case 16: /* Clear NZCV flags and 'it eq' state (false as Z=0) */
+			cpsr = 0x00000800;
+			probe_should_run = 0;
+			break;
+		case 17: /* Set NZCV flags and 'it vc' state (false as V=1) */
+			cpsr = 0xf0007800;
+			probe_should_run = 0;
+			break;
+		case 18: /* Clear NZCV flags and 'it ls' state (true as C=0) */
+			cpsr = 0x00009800;
+			break;
+		case 19: /* Set NZCV flags and 'it cs' state (true as C=1) */
+			cpsr = 0xf0002800;
+			is_last_scenario = true;
+			break;
+		}
+	}
+
+	return cpsr;
+}
+
+static void setup_test_context(struct pt_regs *regs)
+{
+	int scenario = test_case_run_count>>1;
+	unsigned long val;
+	struct test_arg *args;
+	int i;
+
+	is_last_scenario = false;
+	memory_needs_checking = false;
+
+	/* Initialise test memory on stack */
+	val = (scenario & 1) ? VALM : ~VALM;
+	for (i = 0; i < TEST_MEMORY_SIZE / sizeof(current_stack[0]); ++i)
+		current_stack[i] = val + (i << 8);
+	/* Put target of branch on stack for tests which load PC from memory */
+	if (current_branch_target)
+		current_stack[15] = current_branch_target;
+	/* Put a value for SP on stack for tests which load SP from memory */
+	current_stack[13] = (u32)current_stack + 120;
+
+	/* Initialise register values to their default state */
+	val = (scenario & 2) ? VALR : ~VALR;
+	for (i = 0; i < 13; ++i)
+		regs->uregs[i] = val ^ (i << 8);
+	regs->ARM_lr = val ^ (14 << 8);
+	regs->ARM_cpsr &= ~(APSR_MASK | PSR_IT_MASK);
+	regs->ARM_cpsr |= test_context_cpsr(scenario);
+
+	/* Perform testcase specific register setup  */
+	args = current_args;
+	for (; args[0].type != ARG_TYPE_END; ++args)
+		switch (args[0].type) {
+		case ARG_TYPE_REG: {
+			struct test_arg_regptr *arg =
+				(struct test_arg_regptr *)args;
+			regs->uregs[arg->reg] = arg->val;
+			break;
+		}
+		case ARG_TYPE_PTR: {
+			struct test_arg_regptr *arg =
+				(struct test_arg_regptr *)args;
+			regs->uregs[arg->reg] =
+				(unsigned long)current_stack + arg->val;
+			memory_needs_checking = true;
+			break;
+		}
+		case ARG_TYPE_MEM: {
+			struct test_arg_mem *arg = (struct test_arg_mem *)args;
+			current_stack[arg->index] = arg->val;
+			break;
+		}
+		default:
+			break;
+		}
+}
+
+struct test_probe {
+	struct kprobe	kprobe;
+	bool		registered;
+	int		hit;
+};
+
+static void unregister_test_probe(struct test_probe *probe)
+{
+	if (probe->registered) {
+		unregister_kprobe(&probe->kprobe);
+		probe->kprobe.flags = 0; /* Clear disable flag to allow reuse */
+	}
+	probe->registered = false;
+}
+
+static int register_test_probe(struct test_probe *probe)
+{
+	int ret;
+
+	if (probe->registered)
+		BUG();
+
+	ret = register_kprobe(&probe->kprobe);
+	if (ret >= 0) {
+		probe->registered = true;
+		probe->hit = -1;
+	}
+	return ret;
+}
+
+static int __kprobes
+test_before_pre_handler(struct kprobe *p, struct pt_regs *regs)
+{
+	container_of(p, struct test_probe, kprobe)->hit = test_instance;
+	return 0;
+}
+
+static void __kprobes
+test_before_post_handler(struct kprobe *p, struct pt_regs *regs,
+							unsigned long flags)
+{
+	setup_test_context(regs);
+	initial_regs = *regs;
+	initial_regs.ARM_cpsr &= ~PSR_IGNORE_BITS;
+}
+
+static int __kprobes
+test_case_pre_handler(struct kprobe *p, struct pt_regs *regs)
+{
+	container_of(p, struct test_probe, kprobe)->hit = test_instance;
+	return 0;
+}
+
+static int __kprobes
+test_after_pre_handler(struct kprobe *p, struct pt_regs *regs)
+{
+	if (container_of(p, struct test_probe, kprobe)->hit == test_instance)
+		return 0; /* Already run for this test instance */
+
+	result_regs = *regs;
+	result_regs.ARM_cpsr &= ~PSR_IGNORE_BITS;
+
+	/* Undo any changes done to SP by the test case */
+	regs->ARM_sp = (unsigned long)current_stack;
+
+	container_of(p, struct test_probe, kprobe)->hit = test_instance;
+	return 0;
+}
+
+static struct test_probe test_before_probe = {
+	.kprobe.pre_handler	= test_before_pre_handler,
+	.kprobe.post_handler	= test_before_post_handler,
+};
+
+static struct test_probe test_case_probe = {
+	.kprobe.pre_handler	= test_case_pre_handler,
+};
+
+static struct test_probe test_after_probe = {
+	.kprobe.pre_handler	= test_after_pre_handler,
+};
+
+static struct test_probe test_after2_probe = {
+	.kprobe.pre_handler	= test_after_pre_handler,
+};
+
+static void test_case_cleanup(void)
+{
+	unregister_test_probe(&test_before_probe);
+	unregister_test_probe(&test_case_probe);
+	unregister_test_probe(&test_after_probe);
+	unregister_test_probe(&test_after2_probe);
+}
+
+static void print_registers(struct pt_regs *regs)
+{
+	pr_err("r0  %08lx | r1  %08lx | r2  %08lx | r3  %08lx\n",
+		regs->ARM_r0, regs->ARM_r1, regs->ARM_r2, regs->ARM_r3);
+	pr_err("r4  %08lx | r5  %08lx | r6  %08lx | r7  %08lx\n",
+		regs->ARM_r4, regs->ARM_r5, regs->ARM_r6, regs->ARM_r7);
+	pr_err("r8  %08lx | r9  %08lx | r10 %08lx | r11 %08lx\n",
+		regs->ARM_r8, regs->ARM_r9, regs->ARM_r10, regs->ARM_fp);
+	pr_err("r12 %08lx | sp  %08lx | lr  %08lx | pc  %08lx\n",
+		regs->ARM_ip, regs->ARM_sp, regs->ARM_lr, regs->ARM_pc);
+	pr_err("cpsr %08lx\n", regs->ARM_cpsr);
+}
+
+static void print_memory(u32 *mem, size_t size)
+{
+	int i;
+	for (i = 0; i < size / sizeof(u32); i += 4)
+		pr_err("%08x %08x %08x %08x\n", mem[i], mem[i+1],
+						mem[i+2], mem[i+3]);
+}
+
+static size_t expected_memory_size(u32 *sp)
+{
+	size_t size = sizeof(expected_memory);
+	int offset = (uintptr_t)sp - (uintptr_t)current_stack;
+	if (offset > 0)
+		size -= offset;
+	return size;
+}
+
+static void test_case_failed(const char *message)
+{
+	test_case_cleanup();
+
+	pr_err("FAIL: %s\n", message);
+	pr_err("FAIL: Test %s\n", current_title);
+	pr_err("FAIL: Scenario %d\n", test_case_run_count >> 1);
+}
+
+static unsigned long next_instruction(unsigned long pc)
+{
+#ifdef CONFIG_THUMB2_KERNEL
+	if ((pc & 1) && !is_wide_instruction(*(u16 *)(pc - 1)))
+		return pc + 2;
+	else
+#endif
+	return pc + 4;
+}
+
+static uintptr_t __used kprobes_test_case_start(const char *title, void *stack)
+{
+	struct test_arg *args;
+	struct test_arg_end *end_arg;
+	unsigned long test_code;
+
+	args = (struct test_arg *)PTR_ALIGN(title + strlen(title) + 1, 4);
+
+	current_title = title;
+	current_args = args;
+	current_stack = stack;
+
+	++test_try_count;
+
+	while (args->type != ARG_TYPE_END)
+		++args;
+	end_arg = (struct test_arg_end *)args;
+
+	test_code = (unsigned long)(args + 1); /* Code starts after args */
+
+	test_case_is_thumb = end_arg->flags & ARG_FLAG_THUMB;
+	if (test_case_is_thumb)
+		test_code |= 1;
+
+	current_code_start = test_code;
+
+	current_branch_target = 0;
+	if (end_arg->branch_offset != end_arg->end_offset)
+		current_branch_target = test_code + end_arg->branch_offset;
+
+	test_code += end_arg->code_offset;
+	test_before_probe.kprobe.addr = (kprobe_opcode_t *)test_code;
+
+	test_code = next_instruction(test_code);
+	test_case_probe.kprobe.addr = (kprobe_opcode_t *)test_code;
+
+	if (test_case_is_thumb) {
+		u16 *p = (u16 *)(test_code & ~1);
+		current_instruction = p[0];
+		if (is_wide_instruction(current_instruction)) {
+			current_instruction <<= 16;
+			current_instruction |= p[1];
+		}
+	} else {
+		current_instruction = *(u32 *)test_code;
+	}
+
+	if (current_title[0] == '.')
+		verbose("%s\n", current_title);
+	else
+		verbose("%s\t@ %0*x\n", current_title,
+					test_case_is_thumb ? 4 : 8,
+					current_instruction);
+
+	test_code = next_instruction(test_code);
+	test_after_probe.kprobe.addr = (kprobe_opcode_t *)test_code;
+
+	if (kprobe_test_flags & TEST_FLAG_NARROW_INSTR) {
+		if (!test_case_is_thumb ||
+			is_wide_instruction(current_instruction)) {
+				test_case_failed("expected 16-bit instruction");
+				goto fail;
+		}
+	} else {
+		if (test_case_is_thumb &&
+			!is_wide_instruction(current_instruction)) {
+				test_case_failed("expected 32-bit instruction");
+				goto fail;
+		}
+	}
+
+	coverage_add(current_instruction);
+
+	if (end_arg->flags & ARG_FLAG_UNSUPPORTED) {
+		if (register_test_probe(&test_case_probe) < 0)
+			goto pass;
+		test_case_failed("registered probe for unsupported instruction");
+		goto fail;
+	}
+
+	if (end_arg->flags & ARG_FLAG_SUPPORTED) {
+		if (register_test_probe(&test_case_probe) >= 0)
+			goto pass;
+		test_case_failed("couldn't register probe for supported instruction");
+		goto fail;
+	}
+
+	if (register_test_probe(&test_before_probe) < 0) {
+		test_case_failed("register test_before_probe failed");
+		goto fail;
+	}
+	if (register_test_probe(&test_after_probe) < 0) {
+		test_case_failed("register test_after_probe failed");
+		goto fail;
+	}
+	if (current_branch_target) {
+		test_after2_probe.kprobe.addr =
+				(kprobe_opcode_t *)current_branch_target;
+		if (register_test_probe(&test_after2_probe) < 0) {
+			test_case_failed("register test_after2_probe failed");
+			goto fail;
+		}
+	}
+
+	/* Start first run of test case */
+	test_case_run_count = 0;
+	++test_instance;
+	return current_code_start;
+pass:
+	test_case_run_count = TEST_CASE_PASSED;
+	return (uintptr_t)test_after_probe.kprobe.addr;
+fail:
+	test_case_run_count = TEST_CASE_FAILED;
+	return (uintptr_t)test_after_probe.kprobe.addr;
+}
+
+static bool check_test_results(void)
+{
+	size_t mem_size = 0;
+	u32 *mem = 0;
+
+	if (memcmp(&expected_regs, &result_regs, sizeof(expected_regs))) {
+		test_case_failed("registers differ");
+		goto fail;
+	}
+
+	if (memory_needs_checking) {
+		mem = (u32 *)result_regs.ARM_sp;
+		mem_size = expected_memory_size(mem);
+		if (memcmp(expected_memory, mem, mem_size)) {
+			test_case_failed("test memory differs");
+			goto fail;
+		}
+	}
+
+	return true;
+
+fail:
+	pr_err("initial_regs:\n");
+	print_registers(&initial_regs);
+	pr_err("expected_regs:\n");
+	print_registers(&expected_regs);
+	pr_err("result_regs:\n");
+	print_registers(&result_regs);
+
+	if (mem) {
+		pr_err("current_stack=%p\n", current_stack);
+		pr_err("expected_memory:\n");
+		print_memory(expected_memory, mem_size);
+		pr_err("result_memory:\n");
+		print_memory(mem, mem_size);
+	}
+
+	return false;
+}
+
+static uintptr_t __used kprobes_test_case_end(void)
+{
+	if (test_case_run_count < 0) {
+		if (test_case_run_count == TEST_CASE_PASSED)
+			/* kprobes_test_case_start did all the needed testing */
+			goto pass;
+		else
+			/* kprobes_test_case_start failed */
+			goto fail;
+	}
+
+	if (test_before_probe.hit != test_instance) {
+		test_case_failed("test_before_handler not run");
+		goto fail;
+	}
+
+	if (test_after_probe.hit != test_instance &&
+				test_after2_probe.hit != test_instance) {
+		test_case_failed("test_after_handler not run");
+		goto fail;
+	}
+
+	/*
+	 * Even numbered test runs ran without a probe on the test case so
+	 * we can gather reference results. The subsequent odd numbered run
+	 * will have the probe inserted.
+	*/
+	if ((test_case_run_count & 1) == 0) {
+		/* Save results from run without probe */
+		u32 *mem = (u32 *)result_regs.ARM_sp;
+		expected_regs = result_regs;
+		memcpy(expected_memory, mem, expected_memory_size(mem));
+
+		/* Insert probe onto test case instruction */
+		if (register_test_probe(&test_case_probe) < 0) {
+			test_case_failed("register test_case_probe failed");
+			goto fail;
+		}
+	} else {
+		/* Check probe ran as expected */
+		if (probe_should_run == 1) {
+			if (test_case_probe.hit != test_instance) {
+				test_case_failed("test_case_handler not run");
+				goto fail;
+			}
+		} else if (probe_should_run == 0) {
+			if (test_case_probe.hit == test_instance) {
+				test_case_failed("test_case_handler ran");
+				goto fail;
+			}
+		}
+
+		/* Remove probe for any subsequent reference run */
+		unregister_test_probe(&test_case_probe);
+
+		if (!check_test_results())
+			goto fail;
+
+		if (is_last_scenario)
+			goto pass;
+	}
+
+	/* Do next test run */
+	++test_case_run_count;
+	++test_instance;
+	return current_code_start;
+fail:
+	++test_fail_count;
+	goto end;
+pass:
+	++test_pass_count;
+end:
+	test_case_cleanup();
+	return 0;
+}
+
+
+/*
+ * Top level test functions
+ */
+
+static int run_test_cases(void (*tests)(void), const union decode_item *table)
+{
+	int ret;
+
+	pr_info("    Check decoding tables\n");
+	ret = table_test(table);
+	if (ret)
+		return ret;
+
+	pr_info("    Run test cases\n");
+	ret = coverage_start(table);
+	if (ret)
+		return ret;
+
+	tests();
+
+	coverage_end();
+	return 0;
+}
+
+
+static int __init run_all_tests(void)
+{
+	int ret = 0;
+
+	pr_info("Begining kprobe tests...\n");
+
+#ifndef CONFIG_THUMB2_KERNEL
+
+	pr_info("Probe ARM code\n");
+	ret = run_api_tests(arm_func);
+	if (ret)
+		goto out;
+
+	pr_info("ARM instruction simulation\n");
+	ret = run_test_cases(kprobe_arm_test_cases, kprobe_decode_arm_table);
+	if (ret)
+		goto out;
+
+#else /* CONFIG_THUMB2_KERNEL */
+
+	pr_info("Probe 16-bit Thumb code\n");
+	ret = run_api_tests(thumb16_func);
+	if (ret)
+		goto out;
+
+	pr_info("Probe 32-bit Thumb code, even halfword\n");
+	ret = run_api_tests(thumb32even_func);
+	if (ret)
+		goto out;
+
+	pr_info("Probe 32-bit Thumb code, odd halfword\n");
+	ret = run_api_tests(thumb32odd_func);
+	if (ret)
+		goto out;
+
+	pr_info("16-bit Thumb instruction simulation\n");
+	ret = run_test_cases(kprobe_thumb16_test_cases,
+				kprobe_decode_thumb16_table);
+	if (ret)
+		goto out;
+
+	pr_info("32-bit Thumb instruction simulation\n");
+	ret = run_test_cases(kprobe_thumb32_test_cases,
+				kprobe_decode_thumb32_table);
+	if (ret)
+		goto out;
+#endif
+
+	pr_info("Total instruction simulation tests=%d, pass=%d fail=%d\n",
+		test_try_count, test_pass_count, test_fail_count);
+	if (test_fail_count) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+#if BENCHMARKING
+	pr_info("Benchmarks\n");
+	ret = run_benchmarks();
+	if (ret)
+		goto out;
+#endif
+
+#if __LINUX_ARM_ARCH__ >= 7
+	/* We are able to run all test cases so coverage should be complete */
+	if (coverage_fail) {
+		pr_err("FAIL: Test coverage checks failed\n");
+		ret = -EINVAL;
+		goto out;
+	}
+#endif
+
+out:
+	if (ret == 0)
+		pr_info("Finished kprobe tests OK\n");
+	else
+		pr_err("kprobe tests failed\n");
+
+	return ret;
+}
+
+
+/*
+ * Module setup
+ */
+
+#ifdef MODULE
+
+static void __exit kprobe_test_exit(void)
+{
+}
+
+module_init(run_all_tests)
+module_exit(kprobe_test_exit)
+MODULE_LICENSE("GPL");
+
+#else /* !MODULE */
+
+late_initcall(run_all_tests);
+
+#endif
diff --git a/arch/arm/kernel/kprobes-test.h b/arch/arm/kernel/kprobes-test.h
new file mode 100644
index 0000000..0dc5d77
--- /dev/null
+++ b/arch/arm/kernel/kprobes-test.h
@@ -0,0 +1,392 @@
+/*
+ * arch/arm/kernel/kprobes-test.h
+ *
+ * Copyright (C) 2011 Jon Medhurst <tixy@yxit.co.uk>.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define VERBOSE 0 /* Set to '1' for more logging of test cases */
+
+#ifdef CONFIG_THUMB2_KERNEL
+#define NORMAL_ISA "16"
+#else
+#define NORMAL_ISA "32"
+#endif
+
+
+/* Flags used in kprobe_test_flags */
+#define TEST_FLAG_NO_ITBLOCK	(1<<0)
+#define TEST_FLAG_FULL_ITBLOCK	(1<<1)
+#define TEST_FLAG_NARROW_INSTR	(1<<2)
+
+extern int kprobe_test_flags;
+extern int kprobe_test_cc_position;
+
+
+#define TEST_MEMORY_SIZE 256
+
+
+/*
+ * Test case structures.
+ *
+ * The arguments given to test cases can be one of three types.
+ *
+ *   ARG_TYPE_REG
+ *	Load a register with the given value.
+ *
+ *   ARG_TYPE_PTR
+ *	Load a register with a pointer into the stack buffer (SP + given value).
+ *
+ *   ARG_TYPE_MEM
+ *	Store the given value into the stack buffer at [SP+index].
+ *
+ */
+
+#define	ARG_TYPE_END	0
+#define	ARG_TYPE_REG	1
+#define	ARG_TYPE_PTR	2
+#define	ARG_TYPE_MEM	3
+
+#define ARG_FLAG_UNSUPPORTED	0x01
+#define ARG_FLAG_SUPPORTED	0x02
+#define ARG_FLAG_THUMB		0x10	/* Must be 16 so TEST_ISA can be used */
+#define ARG_FLAG_ARM		0x20	/* Must be 32 so TEST_ISA can be used */
+
+struct test_arg {
+	u8	type;		/* ARG_TYPE_x */
+	u8	_padding[7];
+};
+
+struct test_arg_regptr {
+	u8	type;		/* ARG_TYPE_REG or ARG_TYPE_PTR */
+	u8	reg;
+	u8	_padding[2];
+	u32	val;
+};
+
+struct test_arg_mem {
+	u8	type;		/* ARG_TYPE_MEM */
+	u8	index;
+	u8	_padding[2];
+	u32	val;
+};
+
+struct test_arg_end {
+	u8	type;		/* ARG_TYPE_END */
+	u8	flags;		/* ARG_FLAG_x */
+	u16	code_offset;
+	u16	branch_offset;
+	u16	end_offset;
+};
+
+
+/*
+ * Building blocks for test cases.
+ *
+ * Each test case is wrapped between TESTCASE_START and TESTCASE_END.
+ *
+ * To specify arguments for a test case the TEST_ARG_{REG,PTR,MEM} macros are
+ * used followed by a terminating TEST_ARG_END.
+ *
+ * After this, the instruction to be tested is defined with TEST_INSTRUCTION.
+ * Or for branches, TEST_BRANCH_B and TEST_BRANCH_F (branch forwards/backwards).
+ *
+ * Some specific test cases may make use of other custom constructs.
+ */
+
+#if VERBOSE
+#define verbose(fmt, ...) pr_info(fmt, ##__VA_ARGS__)
+#else
+#define verbose(fmt, ...)
+#endif
+
+#define TEST_GROUP(title)					\
+	verbose("\n");						\
+	verbose(title"\n");					\
+	verbose("---------------------------------------------------------\n");
+
+#define TESTCASE_START(title)					\
+	__asm__ __volatile__ (					\
+	"bl	__kprobes_test_case_start		\n\t"	\
+	/* don't use .asciz here as 'title' may be */		\
+	/* multiple strings to be concatenated.  */		\
+	".ascii "#title"				\n\t"	\
+	".byte	0					\n\t"	\
+	".align	2					\n\t"
+
+#define	TEST_ARG_REG(reg, val)					\
+	".byte	"__stringify(ARG_TYPE_REG)"		\n\t"	\
+	".byte	"#reg"					\n\t"	\
+	".short	0					\n\t"	\
+	".word	"#val"					\n\t"
+
+#define	TEST_ARG_PTR(reg, val)					\
+	".byte	"__stringify(ARG_TYPE_PTR)"		\n\t"	\
+	".byte	"#reg"					\n\t"	\
+	".short	0					\n\t"	\
+	".word	"#val"					\n\t"
+
+#define	TEST_ARG_MEM(index, val)				\
+	".byte	"__stringify(ARG_TYPE_MEM)"		\n\t"	\
+	".byte	"#index"				\n\t"	\
+	".short	0					\n\t"	\
+	".word	"#val"					\n\t"
+
+#define	TEST_ARG_END(flags)					\
+	".byte	"__stringify(ARG_TYPE_END)"		\n\t"	\
+	".byte	"TEST_ISA flags"			\n\t"	\
+	".short	50f-0f					\n\t"	\
+	".short	2f-0f					\n\t"	\
+	".short	99f-0f					\n\t"	\
+	".code "TEST_ISA"				\n\t"	\
+	"0:						\n\t"
+
+#define TEST_INSTRUCTION(instruction)				\
+	"50:	nop					\n\t"	\
+	"1:	"instruction"				\n\t"	\
+	"	nop					\n\t"
+
+#define TEST_BRANCH_F(instruction, xtra_dist)			\
+	TEST_INSTRUCTION(instruction)				\
+	".if "#xtra_dist"				\n\t"	\
+	"	b	99f				\n\t"	\
+	".space "#xtra_dist"				\n\t"	\
+	".endif						\n\t"	\
+	"	b	99f				\n\t"	\
+	"2:	nop					\n\t"
+
+#define TEST_BRANCH_B(instruction, xtra_dist)			\
+	"	b	50f				\n\t"	\
+	"	b	99f				\n\t"	\
+	"2:	nop					\n\t"	\
+	"	b	99f				\n\t"	\
+	".if "#xtra_dist"				\n\t"	\
+	".space "#xtra_dist"				\n\t"	\
+	".endif						\n\t"	\
+	TEST_INSTRUCTION(instruction)
+
+#define TESTCASE_END						\
+	"2:						\n\t"	\
+	"99:						\n\t"	\
+	"	bl __kprobes_test_case_end_"TEST_ISA"	\n\t"	\
+	".code "NORMAL_ISA"				\n\t"	\
+	: :							\
+	: "r0", "r1", "r2", "r3", "ip", "lr", "memory", "cc"	\
+	);
+
+
+/*
+ * Macros to define test cases.
+ *
+ * Those of the form TEST_{R,P,M}* can be used to define test cases
+ * which take combinations of the three basic types of arguments. E.g.
+ *
+ *   TEST_R	One register argument
+ *   TEST_RR	Two register arguments
+ *   TEST_RPR	A register, a pointer, then a register argument
+ *
+ * For testing instructions which may branch, there are macros TEST_BF_*
+ * and TEST_BB_* for branching forwards and backwards.
+ *
+ * TEST_SUPPORTED and TEST_UNSUPPORTED don't cause the code to be executed,
+ * the just verify that a kprobe is or is not allowed on the given instruction.
+ */
+
+#define TEST(code)				\
+	TESTCASE_START(code)			\
+	TEST_ARG_END("")			\
+	TEST_INSTRUCTION(code)			\
+	TESTCASE_END
+
+#define TEST_UNSUPPORTED(code)					\
+	TESTCASE_START(code)					\
+	TEST_ARG_END("|"__stringify(ARG_FLAG_UNSUPPORTED))	\
+	TEST_INSTRUCTION(code)					\
+	TESTCASE_END
+
+#define TEST_SUPPORTED(code)					\
+	TESTCASE_START(code)					\
+	TEST_ARG_END("|"__stringify(ARG_FLAG_SUPPORTED))	\
+	TEST_INSTRUCTION(code)					\
+	TESTCASE_END
+
+#define TEST_R(code1, reg, val, code2)			\
+	TESTCASE_START(code1 #reg code2)		\
+	TEST_ARG_REG(reg, val)				\
+	TEST_ARG_END("")				\
+	TEST_INSTRUCTION(code1 #reg code2)		\
+	TESTCASE_END
+
+#define TEST_RR(code1, reg1, val1, code2, reg2, val2, code3)	\
+	TESTCASE_START(code1 #reg1 code2 #reg2 code3)		\
+	TEST_ARG_REG(reg1, val1)				\
+	TEST_ARG_REG(reg2, val2)				\
+	TEST_ARG_END("")					\
+	TEST_INSTRUCTION(code1 #reg1 code2 #reg2 code3)		\
+	TESTCASE_END
+
+#define TEST_RRR(code1, reg1, val1, code2, reg2, val2, code3, reg3, val3, code4)\
+	TESTCASE_START(code1 #reg1 code2 #reg2 code3 #reg3 code4)		\
+	TEST_ARG_REG(reg1, val1)						\
+	TEST_ARG_REG(reg2, val2)						\
+	TEST_ARG_REG(reg3, val3)						\
+	TEST_ARG_END("")							\
+	TEST_INSTRUCTION(code1 #reg1 code2 #reg2 code3 #reg3 code4)		\
+	TESTCASE_END
+
+#define TEST_RRRR(code1, reg1, val1, code2, reg2, val2, code3, reg3, val3, code4, reg4, val4)	\
+	TESTCASE_START(code1 #reg1 code2 #reg2 code3 #reg3 code4 #reg4)		\
+	TEST_ARG_REG(reg1, val1)						\
+	TEST_ARG_REG(reg2, val2)						\
+	TEST_ARG_REG(reg3, val3)						\
+	TEST_ARG_REG(reg4, val4)						\
+	TEST_ARG_END("")							\
+	TEST_INSTRUCTION(code1 #reg1 code2 #reg2 code3 #reg3 code4 #reg4)	\
+	TESTCASE_END
+
+#define TEST_P(code1, reg1, val1, code2)	\
+	TESTCASE_START(code1 #reg1 code2)	\
+	TEST_ARG_PTR(reg1, val1)		\
+	TEST_ARG_END("")			\
+	TEST_INSTRUCTION(code1 #reg1 code2)	\
+	TESTCASE_END
+
+#define TEST_PR(code1, reg1, val1, code2, reg2, val2, code3)	\
+	TESTCASE_START(code1 #reg1 code2 #reg2 code3)		\
+	TEST_ARG_PTR(reg1, val1)				\
+	TEST_ARG_REG(reg2, val2)				\
+	TEST_ARG_END("")					\
+	TEST_INSTRUCTION(code1 #reg1 code2 #reg2 code3)		\
+	TESTCASE_END
+
+#define TEST_RP(code1, reg1, val1, code2, reg2, val2, code3)	\
+	TESTCASE_START(code1 #reg1 code2 #reg2 code3)		\
+	TEST_ARG_REG(reg1, val1)				\
+	TEST_ARG_PTR(reg2, val2)				\
+	TEST_ARG_END("")					\
+	TEST_INSTRUCTION(code1 #reg1 code2 #reg2 code3)		\
+	TESTCASE_END
+
+#define TEST_PRR(code1, reg1, val1, code2, reg2, val2, code3, reg3, val3, code4)\
+	TESTCASE_START(code1 #reg1 code2 #reg2 code3 #reg3 code4)		\
+	TEST_ARG_PTR(reg1, val1)						\
+	TEST_ARG_REG(reg2, val2)						\
+	TEST_ARG_REG(reg3, val3)						\
+	TEST_ARG_END("")							\
+	TEST_INSTRUCTION(code1 #reg1 code2 #reg2 code3 #reg3 code4)		\
+	TESTCASE_END
+
+#define TEST_RPR(code1, reg1, val1, code2, reg2, val2, code3, reg3, val3, code4)\
+	TESTCASE_START(code1 #reg1 code2 #reg2 code3 #reg3 code4)		\
+	TEST_ARG_REG(reg1, val1)						\
+	TEST_ARG_PTR(reg2, val2)						\
+	TEST_ARG_REG(reg3, val3)						\
+	TEST_ARG_END("")							\
+	TEST_INSTRUCTION(code1 #reg1 code2 #reg2 code3 #reg3 code4)		\
+	TESTCASE_END
+
+#define TEST_RRP(code1, reg1, val1, code2, reg2, val2, code3, reg3, val3, code4)\
+	TESTCASE_START(code1 #reg1 code2 #reg2 code3 #reg3 code4)		\
+	TEST_ARG_REG(reg1, val1)						\
+	TEST_ARG_REG(reg2, val2)						\
+	TEST_ARG_PTR(reg3, val3)						\
+	TEST_ARG_END("")							\
+	TEST_INSTRUCTION(code1 #reg1 code2 #reg2 code3 #reg3 code4)		\
+	TESTCASE_END
+
+#define TEST_BF_P(code1, reg1, val1, code2)	\
+	TESTCASE_START(code1 #reg1 code2)	\
+	TEST_ARG_PTR(reg1, val1)		\
+	TEST_ARG_END("")			\
+	TEST_BRANCH_F(code1 #reg1 code2, 0)	\
+	TESTCASE_END
+
+#define TEST_BF_X(code, xtra_dist)		\
+	TESTCASE_START(code)			\
+	TEST_ARG_END("")			\
+	TEST_BRANCH_F(code, xtra_dist)		\
+	TESTCASE_END
+
+#define TEST_BB_X(code, xtra_dist)		\
+	TESTCASE_START(code)			\
+	TEST_ARG_END("")			\
+	TEST_BRANCH_B(code, xtra_dist)		\
+	TESTCASE_END
+
+#define TEST_BF_RX(code1, reg, val, code2, xtra_dist)	\
+	TESTCASE_START(code1 #reg code2)		\
+	TEST_ARG_REG(reg, val)				\
+	TEST_ARG_END("")				\
+	TEST_BRANCH_F(code1 #reg code2, xtra_dist)	\
+	TESTCASE_END
+
+#define TEST_BB_RX(code1, reg, val, code2, xtra_dist)	\
+	TESTCASE_START(code1 #reg code2)		\
+	TEST_ARG_REG(reg, val)				\
+	TEST_ARG_END("")				\
+	TEST_BRANCH_B(code1 #reg code2, xtra_dist)	\
+	TESTCASE_END
+
+#define TEST_BF(code)	TEST_BF_X(code, 0)
+#define TEST_BB(code)	TEST_BB_X(code, 0)
+
+#define TEST_BF_R(code1, reg, val, code2) TEST_BF_RX(code1, reg, val, code2, 0)
+#define TEST_BB_R(code1, reg, val, code2) TEST_BB_RX(code1, reg, val, code2, 0)
+
+#define TEST_BF_RR(code1, reg1, val1, code2, reg2, val2, code3)	\
+	TESTCASE_START(code1 #reg1 code2 #reg2 code3)		\
+	TEST_ARG_REG(reg1, val1)				\
+	TEST_ARG_REG(reg2, val2)				\
+	TEST_ARG_END("")					\
+	TEST_BRANCH_F(code1 #reg1 code2 #reg2 code3, 0)		\
+	TESTCASE_END
+
+#define TEST_X(code, codex)			\
+	TESTCASE_START(code)			\
+	TEST_ARG_END("")			\
+	TEST_INSTRUCTION(code)			\
+	"	b	99f		\n\t"	\
+	"	"codex"			\n\t"	\
+	TESTCASE_END
+
+#define TEST_RX(code1, reg, val, code2, codex)		\
+	TESTCASE_START(code1 #reg code2)		\
+	TEST_ARG_REG(reg, val)				\
+	TEST_ARG_END("")				\
+	TEST_INSTRUCTION(code1 __stringify(reg) code2)	\
+	"	b	99f		\n\t"		\
+	"	"codex"			\n\t"		\
+	TESTCASE_END
+
+#define TEST_RRX(code1, reg1, val1, code2, reg2, val2, code3, codex)		\
+	TESTCASE_START(code1 #reg1 code2 #reg2 code3)				\
+	TEST_ARG_REG(reg1, val1)						\
+	TEST_ARG_REG(reg2, val2)						\
+	TEST_ARG_END("")							\
+	TEST_INSTRUCTION(code1 __stringify(reg1) code2 __stringify(reg2) code3)	\
+	"	b	99f		\n\t"					\
+	"	"codex"			\n\t"					\
+	TESTCASE_END
+
+
+/* Various values used in test cases... */
+#define N(val)	(val ^ 0xffffffff)
+#define VAL1	0x12345678
+#define VAL2	N(VAL1)
+#define VAL3	0xa5f801
+#define VAL4	N(VAL3)
+#define VALM	0x456789ab
+#define VALR	0xdeaddead
+#define HH1	0x0123fecb
+#define HH2	0xa9874567
+
+
+#ifdef CONFIG_THUMB2_KERNEL
+void kprobe_thumb16_test_cases(void);
+void kprobe_thumb32_test_cases(void);
+#else
+void kprobe_arm_test_cases(void);
+#endif
diff --git a/arch/arm/kernel/kprobes-thumb.c b/arch/arm/kernel/kprobes-thumb.c
index 902ca59..8f96ec7 100644
--- a/arch/arm/kernel/kprobes-thumb.c
+++ b/arch/arm/kernel/kprobes-thumb.c
@@ -10,6 +10,7 @@
 
 #include <linux/kernel.h>
 #include <linux/kprobes.h>
+#include <linux/module.h>
 
 #include "kprobes.h"
 
@@ -943,6 +944,9 @@
 	 */
 	DECODE_END
 };
+#ifdef CONFIG_ARM_KPROBES_TEST_MODULE
+EXPORT_SYMBOL_GPL(kprobe_decode_thumb32_table);
+#endif
 
 static void __kprobes
 t16_simulate_bxblx(struct kprobe *p, struct pt_regs *regs)
@@ -1423,6 +1427,9 @@
 
 	DECODE_END
 };
+#ifdef CONFIG_ARM_KPROBES_TEST_MODULE
+EXPORT_SYMBOL_GPL(kprobe_decode_thumb16_table);
+#endif
 
 static unsigned long __kprobes thumb_check_cc(unsigned long cpsr)
 {
diff --git a/arch/arm/kernel/kprobes.h b/arch/arm/kernel/kprobes.h
index a6aeda0..38945f7 100644
--- a/arch/arm/kernel/kprobes.h
+++ b/arch/arm/kernel/kprobes.h
@@ -413,6 +413,14 @@
 	DECODE_HEADER(DECODE_TYPE_REJECT, _mask, _value, 0)
 
 
+#ifdef CONFIG_THUMB2_KERNEL
+extern const union decode_item kprobe_decode_thumb16_table[];
+extern const union decode_item kprobe_decode_thumb32_table[];
+#else
+extern const union decode_item kprobe_decode_arm_table[];
+#endif
+
+
 int kprobe_decode_insn(kprobe_opcode_t insn, struct arch_specific_insn *asi,
 			const union decode_item *table, bool thumb16);
 
diff --git a/arch/arm/kernel/perf_event.c b/arch/arm/kernel/perf_event.c
index 53c9c26..e6e5d7c 100644
--- a/arch/arm/kernel/perf_event.c
+++ b/arch/arm/kernel/perf_event.c
@@ -12,6 +12,7 @@
  */
 #define pr_fmt(fmt) "hw perfevents: " fmt
 
+#include <linux/bitmap.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
@@ -26,16 +27,8 @@
 #include <asm/pmu.h>
 #include <asm/stacktrace.h>
 
-static struct platform_device *pmu_device;
-
 /*
- * Hardware lock to serialize accesses to PMU registers. Needed for the
- * read/modify/write sequences.
- */
-static DEFINE_RAW_SPINLOCK(pmu_lock);
-
-/*
- * ARMv6 supports a maximum of 3 events, starting from index 1. If we add
+ * ARMv6 supports a maximum of 3 events, starting from index 0. If we add
  * another platform that supports more, we need to increase this to be the
  * largest of all platforms.
  *
@@ -43,62 +36,24 @@
  *  cycle counter CCNT + 31 events counters CNT0..30.
  *  Cortex-A8 has 1+4 counters, Cortex-A9 has 1+6 counters.
  */
-#define ARMPMU_MAX_HWEVENTS		33
+#define ARMPMU_MAX_HWEVENTS		32
 
-/* The events for a given CPU. */
-struct cpu_hw_events {
-	/*
-	 * The events that are active on the CPU for the given index. Index 0
-	 * is reserved.
-	 */
-	struct perf_event	*events[ARMPMU_MAX_HWEVENTS];
+static DEFINE_PER_CPU(struct perf_event * [ARMPMU_MAX_HWEVENTS], hw_events);
+static DEFINE_PER_CPU(unsigned long [BITS_TO_LONGS(ARMPMU_MAX_HWEVENTS)], used_mask);
+static DEFINE_PER_CPU(struct pmu_hw_events, cpu_hw_events);
 
-	/*
-	 * A 1 bit for an index indicates that the counter is being used for
-	 * an event. A 0 means that the counter can be used.
-	 */
-	unsigned long		used_mask[BITS_TO_LONGS(ARMPMU_MAX_HWEVENTS)];
-
-	/*
-	 * A 1 bit for an index indicates that the counter is actively being
-	 * used.
-	 */
-	unsigned long		active_mask[BITS_TO_LONGS(ARMPMU_MAX_HWEVENTS)];
-};
-static DEFINE_PER_CPU(struct cpu_hw_events, cpu_hw_events);
-
-struct arm_pmu {
-	enum arm_perf_pmu_ids id;
-	const char	*name;
-	irqreturn_t	(*handle_irq)(int irq_num, void *dev);
-	void		(*enable)(struct hw_perf_event *evt, int idx);
-	void		(*disable)(struct hw_perf_event *evt, int idx);
-	int		(*get_event_idx)(struct cpu_hw_events *cpuc,
-					 struct hw_perf_event *hwc);
-	u32		(*read_counter)(int idx);
-	void		(*write_counter)(int idx, u32 val);
-	void		(*start)(void);
-	void		(*stop)(void);
-	void		(*reset)(void *);
-	const unsigned	(*cache_map)[PERF_COUNT_HW_CACHE_MAX]
-				    [PERF_COUNT_HW_CACHE_OP_MAX]
-				    [PERF_COUNT_HW_CACHE_RESULT_MAX];
-	const unsigned	(*event_map)[PERF_COUNT_HW_MAX];
-	u32		raw_event_mask;
-	int		num_events;
-	u64		max_period;
-};
+#define to_arm_pmu(p) (container_of(p, struct arm_pmu, pmu))
 
 /* Set at runtime when we know what CPU type we are. */
-static const struct arm_pmu *armpmu;
+static struct arm_pmu *cpu_pmu;
 
 enum arm_perf_pmu_ids
 armpmu_get_pmu_id(void)
 {
 	int id = -ENODEV;
 
-	if (armpmu != NULL)
-		id = armpmu->id;
+	if (cpu_pmu != NULL)
+		id = cpu_pmu->id;
 
 	return id;
 }
@@ -109,8 +64,8 @@
 {
 	int max_events = 0;
 
-	if (armpmu != NULL)
-		max_events = armpmu->num_events;
+	if (cpu_pmu != NULL)
+		max_events = cpu_pmu->num_events;
 
 	return max_events;
 }
@@ -130,7 +85,11 @@
 #define CACHE_OP_UNSUPPORTED		0xFFFF
 
 static int
-armpmu_map_cache_event(u64 config)
+armpmu_map_cache_event(const unsigned (*cache_map)
+				      [PERF_COUNT_HW_CACHE_MAX]
+				      [PERF_COUNT_HW_CACHE_OP_MAX]
+				      [PERF_COUNT_HW_CACHE_RESULT_MAX],
+		       u64 config)
 {
 	unsigned int cache_type, cache_op, cache_result, ret;
 
@@ -146,7 +105,7 @@
 	if (cache_result >= PERF_COUNT_HW_CACHE_RESULT_MAX)
 		return -EINVAL;
 
-	ret = (int)(*armpmu->cache_map)[cache_type][cache_op][cache_result];
+	ret = (int)(*cache_map)[cache_type][cache_op][cache_result];
 
 	if (ret == CACHE_OP_UNSUPPORTED)
 		return -ENOENT;
@@ -155,23 +114,46 @@
 }
 
 static int
-armpmu_map_event(u64 config)
+armpmu_map_event(const unsigned (*event_map)[PERF_COUNT_HW_MAX], u64 config)
 {
-	int mapping = (*armpmu->event_map)[config];
-	return mapping == HW_OP_UNSUPPORTED ? -EOPNOTSUPP : mapping;
+	int mapping = (*event_map)[config];
+	return mapping == HW_OP_UNSUPPORTED ? -ENOENT : mapping;
 }
 
 static int
-armpmu_map_raw_event(u64 config)
+armpmu_map_raw_event(u32 raw_event_mask, u64 config)
 {
-	return (int)(config & armpmu->raw_event_mask);
+	return (int)(config & raw_event_mask);
 }
 
-static int
+static int map_cpu_event(struct perf_event *event,
+			 const unsigned (*event_map)[PERF_COUNT_HW_MAX],
+			 const unsigned (*cache_map)
+					[PERF_COUNT_HW_CACHE_MAX]
+					[PERF_COUNT_HW_CACHE_OP_MAX]
+					[PERF_COUNT_HW_CACHE_RESULT_MAX],
+			 u32 raw_event_mask)
+{
+	u64 config = event->attr.config;
+
+	switch (event->attr.type) {
+	case PERF_TYPE_HARDWARE:
+		return armpmu_map_event(event_map, config);
+	case PERF_TYPE_HW_CACHE:
+		return armpmu_map_cache_event(cache_map, config);
+	case PERF_TYPE_RAW:
+		return armpmu_map_raw_event(raw_event_mask, config);
+	}
+
+	return -ENOENT;
+}
+
+int
 armpmu_event_set_period(struct perf_event *event,
 			struct hw_perf_event *hwc,
 			int idx)
 {
+	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
 	s64 left = local64_read(&hwc->period_left);
 	s64 period = hwc->sample_period;
 	int ret = 0;
@@ -202,11 +184,12 @@
 	return ret;
 }
 
-static u64
+u64
 armpmu_event_update(struct perf_event *event,
 		    struct hw_perf_event *hwc,
 		    int idx, int overflow)
 {
+	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
 	u64 delta, prev_raw_count, new_raw_count;
 
 again:
@@ -246,11 +229,9 @@
 static void
 armpmu_stop(struct perf_event *event, int flags)
 {
+	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
 	struct hw_perf_event *hwc = &event->hw;
 
-	if (!armpmu)
-		return;
-
 	/*
 	 * ARM pmu always has to update the counter, so ignore
 	 * PERF_EF_UPDATE, see comments in armpmu_start().
@@ -266,11 +247,9 @@
 static void
 armpmu_start(struct perf_event *event, int flags)
 {
+	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
 	struct hw_perf_event *hwc = &event->hw;
 
-	if (!armpmu)
-		return;
-
 	/*
 	 * ARM pmu always has to reprogram the period, so ignore
 	 * PERF_EF_RELOAD, see the comment below.
@@ -293,16 +272,16 @@
 static void
 armpmu_del(struct perf_event *event, int flags)
 {
-	struct cpu_hw_events *cpuc = &__get_cpu_var(cpu_hw_events);
+	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
+	struct pmu_hw_events *hw_events = armpmu->get_hw_events();
 	struct hw_perf_event *hwc = &event->hw;
 	int idx = hwc->idx;
 
 	WARN_ON(idx < 0);
 
-	clear_bit(idx, cpuc->active_mask);
 	armpmu_stop(event, PERF_EF_UPDATE);
-	cpuc->events[idx] = NULL;
-	clear_bit(idx, cpuc->used_mask);
+	hw_events->events[idx] = NULL;
+	clear_bit(idx, hw_events->used_mask);
 
 	perf_event_update_userpage(event);
 }
@@ -310,7 +289,8 @@
 static int
 armpmu_add(struct perf_event *event, int flags)
 {
-	struct cpu_hw_events *cpuc = &__get_cpu_var(cpu_hw_events);
+	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
+	struct pmu_hw_events *hw_events = armpmu->get_hw_events();
 	struct hw_perf_event *hwc = &event->hw;
 	int idx;
 	int err = 0;
@@ -318,7 +298,7 @@
 	perf_pmu_disable(event->pmu);
 
 	/* If we don't have a space for the counter then finish early. */
-	idx = armpmu->get_event_idx(cpuc, hwc);
+	idx = armpmu->get_event_idx(hw_events, hwc);
 	if (idx < 0) {
 		err = idx;
 		goto out;
@@ -330,8 +310,7 @@
 	 */
 	event->hw.idx = idx;
 	armpmu->disable(hwc, idx);
-	cpuc->events[idx] = event;
-	set_bit(idx, cpuc->active_mask);
+	hw_events->events[idx] = event;
 
 	hwc->state = PERF_HES_STOPPED | PERF_HES_UPTODATE;
 	if (flags & PERF_EF_START)
@@ -345,25 +324,25 @@
 	return err;
 }
 
-static struct pmu pmu;
-
 static int
-validate_event(struct cpu_hw_events *cpuc,
+validate_event(struct pmu_hw_events *hw_events,
 	       struct perf_event *event)
 {
+	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
 	struct hw_perf_event fake_event = event->hw;
+	struct pmu *leader_pmu = event->group_leader->pmu;
 
-	if (event->pmu != &pmu || event->state <= PERF_EVENT_STATE_OFF)
+	if (event->pmu != leader_pmu || event->state <= PERF_EVENT_STATE_OFF)
 		return 1;
 
-	return armpmu->get_event_idx(cpuc, &fake_event) >= 0;
+	return armpmu->get_event_idx(hw_events, &fake_event) >= 0;
 }
 
 static int
 validate_group(struct perf_event *event)
 {
 	struct perf_event *sibling, *leader = event->group_leader;
-	struct cpu_hw_events fake_pmu;
+	struct pmu_hw_events fake_pmu;
 
 	memset(&fake_pmu, 0, sizeof(fake_pmu));
 
@@ -383,110 +362,119 @@
 
 static irqreturn_t armpmu_platform_irq(int irq, void *dev)
 {
-	struct arm_pmu_platdata *plat = dev_get_platdata(&pmu_device->dev);
+	struct arm_pmu *armpmu = (struct arm_pmu *) dev;
+	struct platform_device *plat_device = armpmu->plat_device;
+	struct arm_pmu_platdata *plat = dev_get_platdata(&plat_device->dev);
 
 	return plat->handle_irq(irq, dev, armpmu->handle_irq);
 }
 
+static void
+armpmu_release_hardware(struct arm_pmu *armpmu)
+{
+	int i, irq, irqs;
+	struct platform_device *pmu_device = armpmu->plat_device;
+
+	irqs = min(pmu_device->num_resources, num_possible_cpus());
+
+	for (i = 0; i < irqs; ++i) {
+		if (!cpumask_test_and_clear_cpu(i, &armpmu->active_irqs))
+			continue;
+		irq = platform_get_irq(pmu_device, i);
+		if (irq >= 0)
+			free_irq(irq, armpmu);
+	}
+
+	release_pmu(armpmu->type);
+}
+
 static int
-armpmu_reserve_hardware(void)
+armpmu_reserve_hardware(struct arm_pmu *armpmu)
 {
 	struct arm_pmu_platdata *plat;
 	irq_handler_t handle_irq;
-	int i, err = -ENODEV, irq;
+	int i, err, irq, irqs;
+	struct platform_device *pmu_device = armpmu->plat_device;
 
-	pmu_device = reserve_pmu(ARM_PMU_DEVICE_CPU);
-	if (IS_ERR(pmu_device)) {
+	err = reserve_pmu(armpmu->type);
+	if (err) {
 		pr_warning("unable to reserve pmu\n");
-		return PTR_ERR(pmu_device);
+		return err;
 	}
 
-	init_pmu(ARM_PMU_DEVICE_CPU);
-
 	plat = dev_get_platdata(&pmu_device->dev);
 	if (plat && plat->handle_irq)
 		handle_irq = armpmu_platform_irq;
 	else
 		handle_irq = armpmu->handle_irq;
 
-	if (pmu_device->num_resources < 1) {
+	irqs = min(pmu_device->num_resources, num_possible_cpus());
+	if (irqs < 1) {
 		pr_err("no irqs for PMUs defined\n");
 		return -ENODEV;
 	}
 
-	for (i = 0; i < pmu_device->num_resources; ++i) {
+	for (i = 0; i < irqs; ++i) {
+		err = 0;
 		irq = platform_get_irq(pmu_device, i);
 		if (irq < 0)
 			continue;
 
+		/*
+		 * If we have a single PMU interrupt that we can't shift,
+		 * assume that we're running on a uniprocessor machine and
+		 * continue. Otherwise, continue without this interrupt.
+		 */
+		if (irq_set_affinity(irq, cpumask_of(i)) && irqs > 1) {
+			pr_warning("unable to set irq affinity (irq=%d, cpu=%u)\n",
+				    irq, i);
+			continue;
+		}
+
 		err = request_irq(irq, handle_irq,
 				  IRQF_DISABLED | IRQF_NOBALANCING,
-				  "armpmu", NULL);
+				  "arm-pmu", armpmu);
 		if (err) {
-			pr_warning("unable to request IRQ%d for ARM perf "
-				"counters\n", irq);
-			break;
+			pr_err("unable to request IRQ%d for ARM PMU counters\n",
+				irq);
+			armpmu_release_hardware(armpmu);
+			return err;
 		}
+
+		cpumask_set_cpu(i, &armpmu->active_irqs);
 	}
 
-	if (err) {
-		for (i = i - 1; i >= 0; --i) {
-			irq = platform_get_irq(pmu_device, i);
-			if (irq >= 0)
-				free_irq(irq, NULL);
-		}
-		release_pmu(ARM_PMU_DEVICE_CPU);
-		pmu_device = NULL;
-	}
-
-	return err;
+	return 0;
 }
 
 static void
-armpmu_release_hardware(void)
-{
-	int i, irq;
-
-	for (i = pmu_device->num_resources - 1; i >= 0; --i) {
-		irq = platform_get_irq(pmu_device, i);
-		if (irq >= 0)
-			free_irq(irq, NULL);
-	}
-	armpmu->stop();
-
-	release_pmu(ARM_PMU_DEVICE_CPU);
-	pmu_device = NULL;
-}
-
-static atomic_t active_events = ATOMIC_INIT(0);
-static DEFINE_MUTEX(pmu_reserve_mutex);
-
-static void
 hw_perf_event_destroy(struct perf_event *event)
 {
-	if (atomic_dec_and_mutex_lock(&active_events, &pmu_reserve_mutex)) {
-		armpmu_release_hardware();
-		mutex_unlock(&pmu_reserve_mutex);
+	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
+	atomic_t *active_events	 = &armpmu->active_events;
+	struct mutex *pmu_reserve_mutex = &armpmu->reserve_mutex;
+
+	if (atomic_dec_and_mutex_lock(active_events, pmu_reserve_mutex)) {
+		armpmu_release_hardware(armpmu);
+		mutex_unlock(pmu_reserve_mutex);
 	}
 }
 
 static int
+event_requires_mode_exclusion(struct perf_event_attr *attr)
+{
+	return attr->exclude_idle || attr->exclude_user ||
+	       attr->exclude_kernel || attr->exclude_hv;
+}
+
+static int
 __hw_perf_event_init(struct perf_event *event)
 {
+	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
 	struct hw_perf_event *hwc = &event->hw;
 	int mapping, err;
 
-	/* Decode the generic type into an ARM event identifier. */
-	if (PERF_TYPE_HARDWARE == event->attr.type) {
-		mapping = armpmu_map_event(event->attr.config);
-	} else if (PERF_TYPE_HW_CACHE == event->attr.type) {
-		mapping = armpmu_map_cache_event(event->attr.config);
-	} else if (PERF_TYPE_RAW == event->attr.type) {
-		mapping = armpmu_map_raw_event(event->attr.config);
-	} else {
-		pr_debug("event type %x not supported\n", event->attr.type);
-		return -EOPNOTSUPP;
-	}
+	mapping = armpmu->map_event(event);
 
 	if (mapping < 0) {
 		pr_debug("event %x:%llx not supported\n", event->attr.type,
@@ -495,34 +483,31 @@
 	}
 
 	/*
-	 * Check whether we need to exclude the counter from certain modes.
-	 * The ARM performance counters are on all of the time so if someone
-	 * has asked us for some excludes then we have to fail.
+	 * We don't assign an index until we actually place the event onto
+	 * hardware. Use -1 to signify that we haven't decided where to put it
+	 * yet. For SMP systems, each core has it's own PMU so we can't do any
+	 * clever allocation or constraints checking at this point.
 	 */
-	if (event->attr.exclude_kernel || event->attr.exclude_user ||
-	    event->attr.exclude_hv || event->attr.exclude_idle) {
+	hwc->idx		= -1;
+	hwc->config_base	= 0;
+	hwc->config		= 0;
+	hwc->event_base		= 0;
+
+	/*
+	 * Check whether we need to exclude the counter from certain modes.
+	 */
+	if ((!armpmu->set_event_filter ||
+	     armpmu->set_event_filter(hwc, &event->attr)) &&
+	     event_requires_mode_exclusion(&event->attr)) {
 		pr_debug("ARM performance counters do not support "
 			 "mode exclusion\n");
 		return -EPERM;
 	}
 
 	/*
-	 * We don't assign an index until we actually place the event onto
-	 * hardware. Use -1 to signify that we haven't decided where to put it
-	 * yet. For SMP systems, each core has it's own PMU so we can't do any
-	 * clever allocation or constraints checking at this point.
+	 * Store the event encoding into the config_base field.
 	 */
-	hwc->idx = -1;
-
-	/*
-	 * Store the event encoding into the config_base field. config and
-	 * event_base are unused as the only 2 things we need to know are
-	 * the event mapping and the counter to use. The counter to use is
-	 * also the indx and the config_base is the event type.
-	 */
-	hwc->config_base	    = (unsigned long)mapping;
-	hwc->config		    = 0;
-	hwc->event_base		    = 0;
+	hwc->config_base	    |= (unsigned long)mapping;
 
 	if (!hwc->sample_period) {
 		hwc->sample_period  = armpmu->max_period;
@@ -542,32 +527,23 @@
 
 static int armpmu_event_init(struct perf_event *event)
 {
+	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
 	int err = 0;
+	atomic_t *active_events = &armpmu->active_events;
 
-	switch (event->attr.type) {
-	case PERF_TYPE_RAW:
-	case PERF_TYPE_HARDWARE:
-	case PERF_TYPE_HW_CACHE:
-		break;
-
-	default:
+	if (armpmu->map_event(event) == -ENOENT)
 		return -ENOENT;
-	}
-
-	if (!armpmu)
-		return -ENODEV;
 
 	event->destroy = hw_perf_event_destroy;
 
-	if (!atomic_inc_not_zero(&active_events)) {
-		mutex_lock(&pmu_reserve_mutex);
-		if (atomic_read(&active_events) == 0) {
-			err = armpmu_reserve_hardware();
-		}
+	if (!atomic_inc_not_zero(active_events)) {
+		mutex_lock(&armpmu->reserve_mutex);
+		if (atomic_read(active_events) == 0)
+			err = armpmu_reserve_hardware(armpmu);
 
 		if (!err)
-			atomic_inc(&active_events);
-		mutex_unlock(&pmu_reserve_mutex);
+			atomic_inc(active_events);
+		mutex_unlock(&armpmu->reserve_mutex);
 	}
 
 	if (err)
@@ -582,22 +558,9 @@
 
 static void armpmu_enable(struct pmu *pmu)
 {
-	/* Enable all of the perf events on hardware. */
-	int idx, enabled = 0;
-	struct cpu_hw_events *cpuc = &__get_cpu_var(cpu_hw_events);
-
-	if (!armpmu)
-		return;
-
-	for (idx = 0; idx <= armpmu->num_events; ++idx) {
-		struct perf_event *event = cpuc->events[idx];
-
-		if (!event)
-			continue;
-
-		armpmu->enable(&event->hw, idx);
-		enabled = 1;
-	}
+	struct arm_pmu *armpmu = to_arm_pmu(pmu);
+	struct pmu_hw_events *hw_events = armpmu->get_hw_events();
+	int enabled = bitmap_weight(hw_events->used_mask, armpmu->num_events);
 
 	if (enabled)
 		armpmu->start();
@@ -605,20 +568,32 @@
 
 static void armpmu_disable(struct pmu *pmu)
 {
-	if (armpmu)
-		armpmu->stop();
+	struct arm_pmu *armpmu = to_arm_pmu(pmu);
+	armpmu->stop();
 }
 
-static struct pmu pmu = {
-	.pmu_enable	= armpmu_enable,
-	.pmu_disable	= armpmu_disable,
-	.event_init	= armpmu_event_init,
-	.add		= armpmu_add,
-	.del		= armpmu_del,
-	.start		= armpmu_start,
-	.stop		= armpmu_stop,
-	.read		= armpmu_read,
-};
+static void __init armpmu_init(struct arm_pmu *armpmu)
+{
+	atomic_set(&armpmu->active_events, 0);
+	mutex_init(&armpmu->reserve_mutex);
+
+	armpmu->pmu = (struct pmu) {
+		.pmu_enable	= armpmu_enable,
+		.pmu_disable	= armpmu_disable,
+		.event_init	= armpmu_event_init,
+		.add		= armpmu_add,
+		.del		= armpmu_del,
+		.start		= armpmu_start,
+		.stop		= armpmu_stop,
+		.read		= armpmu_read,
+	};
+}
+
+int __init armpmu_register(struct arm_pmu *armpmu, char *name, int type)
+{
+	armpmu_init(armpmu);
+	return perf_pmu_register(&armpmu->pmu, name, type);
+}
 
 /* Include the PMU-specific implementations. */
 #include "perf_event_xscale.c"
@@ -630,14 +605,72 @@
  * This requires SMP to be available, so exists as a separate initcall.
  */
 static int __init
-armpmu_reset(void)
+cpu_pmu_reset(void)
 {
-	if (armpmu && armpmu->reset)
-		return on_each_cpu(armpmu->reset, NULL, 1);
+	if (cpu_pmu && cpu_pmu->reset)
+		return on_each_cpu(cpu_pmu->reset, NULL, 1);
 	return 0;
 }
-arch_initcall(armpmu_reset);
+arch_initcall(cpu_pmu_reset);
 
+/*
+ * PMU platform driver and devicetree bindings.
+ */
+static struct of_device_id armpmu_of_device_ids[] = {
+	{.compatible = "arm,cortex-a9-pmu"},
+	{.compatible = "arm,cortex-a8-pmu"},
+	{.compatible = "arm,arm1136-pmu"},
+	{.compatible = "arm,arm1176-pmu"},
+	{},
+};
+
+static struct platform_device_id armpmu_plat_device_ids[] = {
+	{.name = "arm-pmu"},
+	{},
+};
+
+static int __devinit armpmu_device_probe(struct platform_device *pdev)
+{
+	cpu_pmu->plat_device = pdev;
+	return 0;
+}
+
+static struct platform_driver armpmu_driver = {
+	.driver		= {
+		.name	= "arm-pmu",
+		.of_match_table = armpmu_of_device_ids,
+	},
+	.probe		= armpmu_device_probe,
+	.id_table	= armpmu_plat_device_ids,
+};
+
+static int __init register_pmu_driver(void)
+{
+	return platform_driver_register(&armpmu_driver);
+}
+device_initcall(register_pmu_driver);
+
+static struct pmu_hw_events *armpmu_get_cpu_events(void)
+{
+	return &__get_cpu_var(cpu_hw_events);
+}
+
+static void __init cpu_pmu_init(struct arm_pmu *armpmu)
+{
+	int cpu;
+	for_each_possible_cpu(cpu) {
+		struct pmu_hw_events *events = &per_cpu(cpu_hw_events, cpu);
+		events->events = per_cpu(hw_events, cpu);
+		events->used_mask = per_cpu(used_mask, cpu);
+		raw_spin_lock_init(&events->pmu_lock);
+	}
+	armpmu->get_hw_events = armpmu_get_cpu_events;
+	armpmu->type = ARM_PMU_DEVICE_CPU;
+}
+
+/*
+ * CPU PMU identification and registration.
+ */
 static int __init
 init_hw_perf_events(void)
 {
@@ -651,22 +684,22 @@
 		case 0xB360:	/* ARM1136 */
 		case 0xB560:	/* ARM1156 */
 		case 0xB760:	/* ARM1176 */
-			armpmu = armv6pmu_init();
+			cpu_pmu = armv6pmu_init();
 			break;
 		case 0xB020:	/* ARM11mpcore */
-			armpmu = armv6mpcore_pmu_init();
+			cpu_pmu = armv6mpcore_pmu_init();
 			break;
 		case 0xC080:	/* Cortex-A8 */
-			armpmu = armv7_a8_pmu_init();
+			cpu_pmu = armv7_a8_pmu_init();
 			break;
 		case 0xC090:	/* Cortex-A9 */
-			armpmu = armv7_a9_pmu_init();
+			cpu_pmu = armv7_a9_pmu_init();
 			break;
 		case 0xC050:	/* Cortex-A5 */
-			armpmu = armv7_a5_pmu_init();
+			cpu_pmu = armv7_a5_pmu_init();
 			break;
 		case 0xC0F0:	/* Cortex-A15 */
-			armpmu = armv7_a15_pmu_init();
+			cpu_pmu = armv7_a15_pmu_init();
 			break;
 		}
 	/* Intel CPUs [xscale]. */
@@ -674,23 +707,23 @@
 		part_number = (cpuid >> 13) & 0x7;
 		switch (part_number) {
 		case 1:
-			armpmu = xscale1pmu_init();
+			cpu_pmu = xscale1pmu_init();
 			break;
 		case 2:
-			armpmu = xscale2pmu_init();
+			cpu_pmu = xscale2pmu_init();
 			break;
 		}
 	}
 
-	if (armpmu) {
+	if (cpu_pmu) {
 		pr_info("enabled with %s PMU driver, %d counters available\n",
-			armpmu->name, armpmu->num_events);
+			cpu_pmu->name, cpu_pmu->num_events);
+		cpu_pmu_init(cpu_pmu);
+		armpmu_register(cpu_pmu, "cpu", PERF_TYPE_RAW);
 	} else {
 		pr_info("no hardware support available\n");
 	}
 
-	perf_pmu_register(&pmu, "cpu", PERF_TYPE_RAW);
-
 	return 0;
 }
 early_initcall(init_hw_perf_events);
diff --git a/arch/arm/kernel/perf_event_v6.c b/arch/arm/kernel/perf_event_v6.c
index dd7f3b9..e63d811 100644
--- a/arch/arm/kernel/perf_event_v6.c
+++ b/arch/arm/kernel/perf_event_v6.c
@@ -54,7 +54,7 @@
 };
 
 enum armv6_counters {
-	ARMV6_CYCLE_COUNTER = 1,
+	ARMV6_CYCLE_COUNTER = 0,
 	ARMV6_COUNTER0,
 	ARMV6_COUNTER1,
 };
@@ -433,6 +433,7 @@
 		      int idx)
 {
 	unsigned long val, mask, evt, flags;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	if (ARMV6_CYCLE_COUNTER == idx) {
 		mask	= 0;
@@ -454,12 +455,29 @@
 	 * Mask out the current event and set the counter to count the event
 	 * that we're interested in.
 	 */
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	val = armv6_pmcr_read();
 	val &= ~mask;
 	val |= evt;
 	armv6_pmcr_write(val);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
+}
+
+static int counter_is_active(unsigned long pmcr, int idx)
+{
+	unsigned long mask = 0;
+	if (idx == ARMV6_CYCLE_COUNTER)
+		mask = ARMV6_PMCR_CCOUNT_IEN;
+	else if (idx == ARMV6_COUNTER0)
+		mask = ARMV6_PMCR_COUNT0_IEN;
+	else if (idx == ARMV6_COUNTER1)
+		mask = ARMV6_PMCR_COUNT1_IEN;
+
+	if (mask)
+		return pmcr & mask;
+
+	WARN_ONCE(1, "invalid counter number (%d)\n", idx);
+	return 0;
 }
 
 static irqreturn_t
@@ -468,7 +486,7 @@
 {
 	unsigned long pmcr = armv6_pmcr_read();
 	struct perf_sample_data data;
-	struct cpu_hw_events *cpuc;
+	struct pmu_hw_events *cpuc;
 	struct pt_regs *regs;
 	int idx;
 
@@ -487,11 +505,11 @@
 	perf_sample_data_init(&data, 0);
 
 	cpuc = &__get_cpu_var(cpu_hw_events);
-	for (idx = 0; idx <= armpmu->num_events; ++idx) {
+	for (idx = 0; idx < cpu_pmu->num_events; ++idx) {
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		if (!test_bit(idx, cpuc->active_mask))
+		if (!counter_is_active(pmcr, idx))
 			continue;
 
 		/*
@@ -508,7 +526,7 @@
 			continue;
 
 		if (perf_event_overflow(event, &data, regs))
-			armpmu->disable(hwc, idx);
+			cpu_pmu->disable(hwc, idx);
 	}
 
 	/*
@@ -527,28 +545,30 @@
 armv6pmu_start(void)
 {
 	unsigned long flags, val;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	val = armv6_pmcr_read();
 	val |= ARMV6_PMCR_ENABLE;
 	armv6_pmcr_write(val);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static void
 armv6pmu_stop(void)
 {
 	unsigned long flags, val;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	val = armv6_pmcr_read();
 	val &= ~ARMV6_PMCR_ENABLE;
 	armv6_pmcr_write(val);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static int
-armv6pmu_get_event_idx(struct cpu_hw_events *cpuc,
+armv6pmu_get_event_idx(struct pmu_hw_events *cpuc,
 		       struct hw_perf_event *event)
 {
 	/* Always place a cycle counter into the cycle counter. */
@@ -578,6 +598,7 @@
 		       int idx)
 {
 	unsigned long val, mask, evt, flags;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	if (ARMV6_CYCLE_COUNTER == idx) {
 		mask	= ARMV6_PMCR_CCOUNT_IEN;
@@ -598,12 +619,12 @@
 	 * of ETM bus signal assertion cycles. The external reporting should
 	 * be disabled and so this should never increment.
 	 */
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	val = armv6_pmcr_read();
 	val &= ~mask;
 	val |= evt;
 	armv6_pmcr_write(val);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static void
@@ -611,6 +632,7 @@
 			      int idx)
 {
 	unsigned long val, mask, flags, evt = 0;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	if (ARMV6_CYCLE_COUNTER == idx) {
 		mask	= ARMV6_PMCR_CCOUNT_IEN;
@@ -627,15 +649,21 @@
 	 * Unlike UP ARMv6, we don't have a way of stopping the counters. We
 	 * simply disable the interrupt reporting.
 	 */
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	val = armv6_pmcr_read();
 	val &= ~mask;
 	val |= evt;
 	armv6_pmcr_write(val);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
-static const struct arm_pmu armv6pmu = {
+static int armv6_map_event(struct perf_event *event)
+{
+	return map_cpu_event(event, &armv6_perf_map,
+				&armv6_perf_cache_map, 0xFF);
+}
+
+static struct arm_pmu armv6pmu = {
 	.id			= ARM_PERF_PMU_ID_V6,
 	.name			= "v6",
 	.handle_irq		= armv6pmu_handle_irq,
@@ -646,14 +674,12 @@
 	.get_event_idx		= armv6pmu_get_event_idx,
 	.start			= armv6pmu_start,
 	.stop			= armv6pmu_stop,
-	.cache_map		= &armv6_perf_cache_map,
-	.event_map		= &armv6_perf_map,
-	.raw_event_mask		= 0xFF,
+	.map_event		= armv6_map_event,
 	.num_events		= 3,
 	.max_period		= (1LLU << 32) - 1,
 };
 
-static const struct arm_pmu *__init armv6pmu_init(void)
+static struct arm_pmu *__init armv6pmu_init(void)
 {
 	return &armv6pmu;
 }
@@ -665,7 +691,14 @@
  * disable the interrupt reporting and update the event. When unthrottling we
  * reset the period and enable the interrupt reporting.
  */
-static const struct arm_pmu armv6mpcore_pmu = {
+
+static int armv6mpcore_map_event(struct perf_event *event)
+{
+	return map_cpu_event(event, &armv6mpcore_perf_map,
+				&armv6mpcore_perf_cache_map, 0xFF);
+}
+
+static struct arm_pmu armv6mpcore_pmu = {
 	.id			= ARM_PERF_PMU_ID_V6MP,
 	.name			= "v6mpcore",
 	.handle_irq		= armv6pmu_handle_irq,
@@ -676,24 +709,22 @@
 	.get_event_idx		= armv6pmu_get_event_idx,
 	.start			= armv6pmu_start,
 	.stop			= armv6pmu_stop,
-	.cache_map		= &armv6mpcore_perf_cache_map,
-	.event_map		= &armv6mpcore_perf_map,
-	.raw_event_mask		= 0xFF,
+	.map_event		= armv6mpcore_map_event,
 	.num_events		= 3,
 	.max_period		= (1LLU << 32) - 1,
 };
 
-static const struct arm_pmu *__init armv6mpcore_pmu_init(void)
+static struct arm_pmu *__init armv6mpcore_pmu_init(void)
 {
 	return &armv6mpcore_pmu;
 }
 #else
-static const struct arm_pmu *__init armv6pmu_init(void)
+static struct arm_pmu *__init armv6pmu_init(void)
 {
 	return NULL;
 }
 
-static const struct arm_pmu *__init armv6mpcore_pmu_init(void)
+static struct arm_pmu *__init armv6mpcore_pmu_init(void)
 {
 	return NULL;
 }
diff --git a/arch/arm/kernel/perf_event_v7.c b/arch/arm/kernel/perf_event_v7.c
index 4c85183..98b7573 100644
--- a/arch/arm/kernel/perf_event_v7.c
+++ b/arch/arm/kernel/perf_event_v7.c
@@ -17,6 +17,9 @@
  */
 
 #ifdef CONFIG_CPU_V7
+
+static struct arm_pmu armv7pmu;
+
 /*
  * Common ARMv7 event types
  *
@@ -676,25 +679,26 @@
 };
 
 /*
- * Perf Events counters
+ * Perf Events' indices
  */
-enum armv7_counters {
-	ARMV7_CYCLE_COUNTER		= 1,	/* Cycle counter */
-	ARMV7_COUNTER0			= 2,	/* First event counter */
-};
+#define	ARMV7_IDX_CYCLE_COUNTER	0
+#define	ARMV7_IDX_COUNTER0	1
+#define	ARMV7_IDX_COUNTER_LAST	(ARMV7_IDX_CYCLE_COUNTER + cpu_pmu->num_events - 1)
 
-/*
- * The cycle counter is ARMV7_CYCLE_COUNTER.
- * The first event counter is ARMV7_COUNTER0.
- * The last event counter is (ARMV7_COUNTER0 + armpmu->num_events - 1).
- */
-#define	ARMV7_COUNTER_LAST	(ARMV7_COUNTER0 + armpmu->num_events - 1)
+#define	ARMV7_MAX_COUNTERS	32
+#define	ARMV7_COUNTER_MASK	(ARMV7_MAX_COUNTERS - 1)
 
 /*
  * ARMv7 low level PMNC access
  */
 
 /*
+ * Perf Event to low level counters mapping
+ */
+#define	ARMV7_IDX_TO_COUNTER(x)	\
+	(((x) - ARMV7_IDX_COUNTER0) & ARMV7_COUNTER_MASK)
+
+/*
  * Per-CPU PMNC: config reg
  */
 #define ARMV7_PMNC_E		(1 << 0) /* Enable all counters */
@@ -708,103 +712,76 @@
 #define	ARMV7_PMNC_MASK		0x3f	 /* Mask for writable bits */
 
 /*
- * Available counters
- */
-#define ARMV7_CNT0		0	/* First event counter */
-#define ARMV7_CCNT		31	/* Cycle counter */
-
-/* Perf Event to low level counters mapping */
-#define ARMV7_EVENT_CNT_TO_CNTx	(ARMV7_COUNTER0 - ARMV7_CNT0)
-
-/*
- * CNTENS: counters enable reg
- */
-#define ARMV7_CNTENS_P(idx)	(1 << (idx - ARMV7_EVENT_CNT_TO_CNTx))
-#define ARMV7_CNTENS_C		(1 << ARMV7_CCNT)
-
-/*
- * CNTENC: counters disable reg
- */
-#define ARMV7_CNTENC_P(idx)	(1 << (idx - ARMV7_EVENT_CNT_TO_CNTx))
-#define ARMV7_CNTENC_C		(1 << ARMV7_CCNT)
-
-/*
- * INTENS: counters overflow interrupt enable reg
- */
-#define ARMV7_INTENS_P(idx)	(1 << (idx - ARMV7_EVENT_CNT_TO_CNTx))
-#define ARMV7_INTENS_C		(1 << ARMV7_CCNT)
-
-/*
- * INTENC: counters overflow interrupt disable reg
- */
-#define ARMV7_INTENC_P(idx)	(1 << (idx - ARMV7_EVENT_CNT_TO_CNTx))
-#define ARMV7_INTENC_C		(1 << ARMV7_CCNT)
-
-/*
- * EVTSEL: Event selection reg
- */
-#define	ARMV7_EVTSEL_MASK	0xff		/* Mask for writable bits */
-
-/*
- * SELECT: Counter selection reg
- */
-#define	ARMV7_SELECT_MASK	0x1f		/* Mask for writable bits */
-
-/*
  * FLAG: counters overflow flag status reg
  */
-#define ARMV7_FLAG_P(idx)	(1 << (idx - ARMV7_EVENT_CNT_TO_CNTx))
-#define ARMV7_FLAG_C		(1 << ARMV7_CCNT)
 #define	ARMV7_FLAG_MASK		0xffffffff	/* Mask for writable bits */
 #define	ARMV7_OVERFLOWED_MASK	ARMV7_FLAG_MASK
 
-static inline unsigned long armv7_pmnc_read(void)
+/*
+ * PMXEVTYPER: Event selection reg
+ */
+#define	ARMV7_EVTYPE_MASK	0xc00000ff	/* Mask for writable bits */
+#define	ARMV7_EVTYPE_EVENT	0xff		/* Mask for EVENT bits */
+
+/*
+ * Event filters for PMUv2
+ */
+#define	ARMV7_EXCLUDE_PL1	(1 << 31)
+#define	ARMV7_EXCLUDE_USER	(1 << 30)
+#define	ARMV7_INCLUDE_HYP	(1 << 27)
+
+static inline u32 armv7_pmnc_read(void)
 {
 	u32 val;
 	asm volatile("mrc p15, 0, %0, c9, c12, 0" : "=r"(val));
 	return val;
 }
 
-static inline void armv7_pmnc_write(unsigned long val)
+static inline void armv7_pmnc_write(u32 val)
 {
 	val &= ARMV7_PMNC_MASK;
 	isb();
 	asm volatile("mcr p15, 0, %0, c9, c12, 0" : : "r"(val));
 }
 
-static inline int armv7_pmnc_has_overflowed(unsigned long pmnc)
+static inline int armv7_pmnc_has_overflowed(u32 pmnc)
 {
 	return pmnc & ARMV7_OVERFLOWED_MASK;
 }
 
-static inline int armv7_pmnc_counter_has_overflowed(unsigned long pmnc,
-					enum armv7_counters counter)
+static inline int armv7_pmnc_counter_valid(int idx)
+{
+	return idx >= ARMV7_IDX_CYCLE_COUNTER && idx <= ARMV7_IDX_COUNTER_LAST;
+}
+
+static inline int armv7_pmnc_counter_has_overflowed(u32 pmnc, int idx)
 {
 	int ret = 0;
+	u32 counter;
 
-	if (counter == ARMV7_CYCLE_COUNTER)
-		ret = pmnc & ARMV7_FLAG_C;
-	else if ((counter >= ARMV7_COUNTER0) && (counter <= ARMV7_COUNTER_LAST))
-		ret = pmnc & ARMV7_FLAG_P(counter);
-	else
+	if (!armv7_pmnc_counter_valid(idx)) {
 		pr_err("CPU%u checking wrong counter %d overflow status\n",
-			smp_processor_id(), counter);
+			smp_processor_id(), idx);
+	} else {
+		counter = ARMV7_IDX_TO_COUNTER(idx);
+		ret = pmnc & BIT(counter);
+	}
 
 	return ret;
 }
 
-static inline int armv7_pmnc_select_counter(unsigned int idx)
+static inline int armv7_pmnc_select_counter(int idx)
 {
-	u32 val;
+	u32 counter;
 
-	if ((idx < ARMV7_COUNTER0) || (idx > ARMV7_COUNTER_LAST)) {
-		pr_err("CPU%u selecting wrong PMNC counter"
-			" %d\n", smp_processor_id(), idx);
-		return -1;
+	if (!armv7_pmnc_counter_valid(idx)) {
+		pr_err("CPU%u selecting wrong PMNC counter %d\n",
+			smp_processor_id(), idx);
+		return -EINVAL;
 	}
 
-	val = (idx - ARMV7_EVENT_CNT_TO_CNTx) & ARMV7_SELECT_MASK;
-	asm volatile("mcr p15, 0, %0, c9, c12, 5" : : "r" (val));
+	counter = ARMV7_IDX_TO_COUNTER(idx);
+	asm volatile("mcr p15, 0, %0, c9, c12, 5" : : "r" (counter));
 	isb();
 
 	return idx;
@@ -812,124 +789,95 @@
 
 static inline u32 armv7pmu_read_counter(int idx)
 {
-	unsigned long value = 0;
+	u32 value = 0;
 
-	if (idx == ARMV7_CYCLE_COUNTER)
-		asm volatile("mrc p15, 0, %0, c9, c13, 0" : "=r" (value));
-	else if ((idx >= ARMV7_COUNTER0) && (idx <= ARMV7_COUNTER_LAST)) {
-		if (armv7_pmnc_select_counter(idx) == idx)
-			asm volatile("mrc p15, 0, %0, c9, c13, 2"
-				     : "=r" (value));
-	} else
+	if (!armv7_pmnc_counter_valid(idx))
 		pr_err("CPU%u reading wrong counter %d\n",
 			smp_processor_id(), idx);
+	else if (idx == ARMV7_IDX_CYCLE_COUNTER)
+		asm volatile("mrc p15, 0, %0, c9, c13, 0" : "=r" (value));
+	else if (armv7_pmnc_select_counter(idx) == idx)
+		asm volatile("mrc p15, 0, %0, c9, c13, 2" : "=r" (value));
 
 	return value;
 }
 
 static inline void armv7pmu_write_counter(int idx, u32 value)
 {
-	if (idx == ARMV7_CYCLE_COUNTER)
-		asm volatile("mcr p15, 0, %0, c9, c13, 0" : : "r" (value));
-	else if ((idx >= ARMV7_COUNTER0) && (idx <= ARMV7_COUNTER_LAST)) {
-		if (armv7_pmnc_select_counter(idx) == idx)
-			asm volatile("mcr p15, 0, %0, c9, c13, 2"
-				     : : "r" (value));
-	} else
+	if (!armv7_pmnc_counter_valid(idx))
 		pr_err("CPU%u writing wrong counter %d\n",
 			smp_processor_id(), idx);
+	else if (idx == ARMV7_IDX_CYCLE_COUNTER)
+		asm volatile("mcr p15, 0, %0, c9, c13, 0" : : "r" (value));
+	else if (armv7_pmnc_select_counter(idx) == idx)
+		asm volatile("mcr p15, 0, %0, c9, c13, 2" : : "r" (value));
 }
 
-static inline void armv7_pmnc_write_evtsel(unsigned int idx, u32 val)
+static inline void armv7_pmnc_write_evtsel(int idx, u32 val)
 {
 	if (armv7_pmnc_select_counter(idx) == idx) {
-		val &= ARMV7_EVTSEL_MASK;
+		val &= ARMV7_EVTYPE_MASK;
 		asm volatile("mcr p15, 0, %0, c9, c13, 1" : : "r" (val));
 	}
 }
 
-static inline u32 armv7_pmnc_enable_counter(unsigned int idx)
+static inline int armv7_pmnc_enable_counter(int idx)
 {
-	u32 val;
+	u32 counter;
 
-	if ((idx != ARMV7_CYCLE_COUNTER) &&
-	    ((idx < ARMV7_COUNTER0) || (idx > ARMV7_COUNTER_LAST))) {
-		pr_err("CPU%u enabling wrong PMNC counter"
-			" %d\n", smp_processor_id(), idx);
-		return -1;
+	if (!armv7_pmnc_counter_valid(idx)) {
+		pr_err("CPU%u enabling wrong PMNC counter %d\n",
+			smp_processor_id(), idx);
+		return -EINVAL;
 	}
 
-	if (idx == ARMV7_CYCLE_COUNTER)
-		val = ARMV7_CNTENS_C;
-	else
-		val = ARMV7_CNTENS_P(idx);
-
-	asm volatile("mcr p15, 0, %0, c9, c12, 1" : : "r" (val));
-
+	counter = ARMV7_IDX_TO_COUNTER(idx);
+	asm volatile("mcr p15, 0, %0, c9, c12, 1" : : "r" (BIT(counter)));
 	return idx;
 }
 
-static inline u32 armv7_pmnc_disable_counter(unsigned int idx)
+static inline int armv7_pmnc_disable_counter(int idx)
 {
-	u32 val;
+	u32 counter;
 
-
-	if ((idx != ARMV7_CYCLE_COUNTER) &&
-	    ((idx < ARMV7_COUNTER0) || (idx > ARMV7_COUNTER_LAST))) {
-		pr_err("CPU%u disabling wrong PMNC counter"
-			" %d\n", smp_processor_id(), idx);
-		return -1;
+	if (!armv7_pmnc_counter_valid(idx)) {
+		pr_err("CPU%u disabling wrong PMNC counter %d\n",
+			smp_processor_id(), idx);
+		return -EINVAL;
 	}
 
-	if (idx == ARMV7_CYCLE_COUNTER)
-		val = ARMV7_CNTENC_C;
-	else
-		val = ARMV7_CNTENC_P(idx);
-
-	asm volatile("mcr p15, 0, %0, c9, c12, 2" : : "r" (val));
-
+	counter = ARMV7_IDX_TO_COUNTER(idx);
+	asm volatile("mcr p15, 0, %0, c9, c12, 2" : : "r" (BIT(counter)));
 	return idx;
 }
 
-static inline u32 armv7_pmnc_enable_intens(unsigned int idx)
+static inline int armv7_pmnc_enable_intens(int idx)
 {
-	u32 val;
+	u32 counter;
 
-	if ((idx != ARMV7_CYCLE_COUNTER) &&
-	    ((idx < ARMV7_COUNTER0) || (idx > ARMV7_COUNTER_LAST))) {
-		pr_err("CPU%u enabling wrong PMNC counter"
-			" interrupt enable %d\n", smp_processor_id(), idx);
-		return -1;
+	if (!armv7_pmnc_counter_valid(idx)) {
+		pr_err("CPU%u enabling wrong PMNC counter IRQ enable %d\n",
+			smp_processor_id(), idx);
+		return -EINVAL;
 	}
 
-	if (idx == ARMV7_CYCLE_COUNTER)
-		val = ARMV7_INTENS_C;
-	else
-		val = ARMV7_INTENS_P(idx);
-
-	asm volatile("mcr p15, 0, %0, c9, c14, 1" : : "r" (val));
-
+	counter = ARMV7_IDX_TO_COUNTER(idx);
+	asm volatile("mcr p15, 0, %0, c9, c14, 1" : : "r" (BIT(counter)));
 	return idx;
 }
 
-static inline u32 armv7_pmnc_disable_intens(unsigned int idx)
+static inline int armv7_pmnc_disable_intens(int idx)
 {
-	u32 val;
+	u32 counter;
 
-	if ((idx != ARMV7_CYCLE_COUNTER) &&
-	    ((idx < ARMV7_COUNTER0) || (idx > ARMV7_COUNTER_LAST))) {
-		pr_err("CPU%u disabling wrong PMNC counter"
-			" interrupt enable %d\n", smp_processor_id(), idx);
-		return -1;
+	if (!armv7_pmnc_counter_valid(idx)) {
+		pr_err("CPU%u disabling wrong PMNC counter IRQ enable %d\n",
+			smp_processor_id(), idx);
+		return -EINVAL;
 	}
 
-	if (idx == ARMV7_CYCLE_COUNTER)
-		val = ARMV7_INTENC_C;
-	else
-		val = ARMV7_INTENC_P(idx);
-
-	asm volatile("mcr p15, 0, %0, c9, c14, 2" : : "r" (val));
-
+	counter = ARMV7_IDX_TO_COUNTER(idx);
+	asm volatile("mcr p15, 0, %0, c9, c14, 2" : : "r" (BIT(counter)));
 	return idx;
 }
 
@@ -973,14 +921,14 @@
 	asm volatile("mrc p15, 0, %0, c9, c13, 0" : "=r" (val));
 	printk(KERN_INFO "CCNT  =0x%08x\n", val);
 
-	for (cnt = ARMV7_COUNTER0; cnt < ARMV7_COUNTER_LAST; cnt++) {
+	for (cnt = ARMV7_IDX_COUNTER0; cnt <= ARMV7_IDX_COUNTER_LAST; cnt++) {
 		armv7_pmnc_select_counter(cnt);
 		asm volatile("mrc p15, 0, %0, c9, c13, 2" : "=r" (val));
 		printk(KERN_INFO "CNT[%d] count =0x%08x\n",
-			cnt-ARMV7_EVENT_CNT_TO_CNTx, val);
+			ARMV7_IDX_TO_COUNTER(cnt), val);
 		asm volatile("mrc p15, 0, %0, c9, c13, 1" : "=r" (val));
 		printk(KERN_INFO "CNT[%d] evtsel=0x%08x\n",
-			cnt-ARMV7_EVENT_CNT_TO_CNTx, val);
+			ARMV7_IDX_TO_COUNTER(cnt), val);
 	}
 }
 #endif
@@ -988,12 +936,13 @@
 static void armv7pmu_enable_event(struct hw_perf_event *hwc, int idx)
 {
 	unsigned long flags;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	/*
 	 * Enable counter and interrupt, and set the counter to count
 	 * the event that we're interested in.
 	 */
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 
 	/*
 	 * Disable counter
@@ -1002,9 +951,10 @@
 
 	/*
 	 * Set event (if destined for PMNx counters)
-	 * We don't need to set the event if it's a cycle count
+	 * We only need to set the event for the cycle counter if we
+	 * have the ability to perform event filtering.
 	 */
-	if (idx != ARMV7_CYCLE_COUNTER)
+	if (armv7pmu.set_event_filter || idx != ARMV7_IDX_CYCLE_COUNTER)
 		armv7_pmnc_write_evtsel(idx, hwc->config_base);
 
 	/*
@@ -1017,17 +967,18 @@
 	 */
 	armv7_pmnc_enable_counter(idx);
 
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static void armv7pmu_disable_event(struct hw_perf_event *hwc, int idx)
 {
 	unsigned long flags;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	/*
 	 * Disable counter and interrupt
 	 */
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 
 	/*
 	 * Disable counter
@@ -1039,14 +990,14 @@
 	 */
 	armv7_pmnc_disable_intens(idx);
 
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static irqreturn_t armv7pmu_handle_irq(int irq_num, void *dev)
 {
-	unsigned long pmnc;
+	u32 pmnc;
 	struct perf_sample_data data;
-	struct cpu_hw_events *cpuc;
+	struct pmu_hw_events *cpuc;
 	struct pt_regs *regs;
 	int idx;
 
@@ -1069,13 +1020,10 @@
 	perf_sample_data_init(&data, 0);
 
 	cpuc = &__get_cpu_var(cpu_hw_events);
-	for (idx = 0; idx <= armpmu->num_events; ++idx) {
+	for (idx = 0; idx < cpu_pmu->num_events; ++idx) {
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		if (!test_bit(idx, cpuc->active_mask))
-			continue;
-
 		/*
 		 * We have a single interrupt for all counters. Check that
 		 * each counter has overflowed before we process it.
@@ -1090,7 +1038,7 @@
 			continue;
 
 		if (perf_event_overflow(event, &data, regs))
-			armpmu->disable(hwc, idx);
+			cpu_pmu->disable(hwc, idx);
 	}
 
 	/*
@@ -1108,61 +1056,114 @@
 static void armv7pmu_start(void)
 {
 	unsigned long flags;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	/* Enable all counters */
 	armv7_pmnc_write(armv7_pmnc_read() | ARMV7_PMNC_E);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static void armv7pmu_stop(void)
 {
 	unsigned long flags;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	/* Disable all counters */
 	armv7_pmnc_write(armv7_pmnc_read() & ~ARMV7_PMNC_E);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
-static int armv7pmu_get_event_idx(struct cpu_hw_events *cpuc,
+static int armv7pmu_get_event_idx(struct pmu_hw_events *cpuc,
 				  struct hw_perf_event *event)
 {
 	int idx;
+	unsigned long evtype = event->config_base & ARMV7_EVTYPE_EVENT;
 
 	/* Always place a cycle counter into the cycle counter. */
-	if (event->config_base == ARMV7_PERFCTR_CPU_CYCLES) {
-		if (test_and_set_bit(ARMV7_CYCLE_COUNTER, cpuc->used_mask))
+	if (evtype == ARMV7_PERFCTR_CPU_CYCLES) {
+		if (test_and_set_bit(ARMV7_IDX_CYCLE_COUNTER, cpuc->used_mask))
 			return -EAGAIN;
 
-		return ARMV7_CYCLE_COUNTER;
-	} else {
-		/*
-		 * For anything other than a cycle counter, try and use
-		 * the events counters
-		 */
-		for (idx = ARMV7_COUNTER0; idx <= armpmu->num_events; ++idx) {
-			if (!test_and_set_bit(idx, cpuc->used_mask))
-				return idx;
-		}
-
-		/* The counters are all in use. */
-		return -EAGAIN;
+		return ARMV7_IDX_CYCLE_COUNTER;
 	}
+
+	/*
+	 * For anything other than a cycle counter, try and use
+	 * the events counters
+	 */
+	for (idx = ARMV7_IDX_COUNTER0; idx < cpu_pmu->num_events; ++idx) {
+		if (!test_and_set_bit(idx, cpuc->used_mask))
+			return idx;
+	}
+
+	/* The counters are all in use. */
+	return -EAGAIN;
+}
+
+/*
+ * Add an event filter to a given event. This will only work for PMUv2 PMUs.
+ */
+static int armv7pmu_set_event_filter(struct hw_perf_event *event,
+				     struct perf_event_attr *attr)
+{
+	unsigned long config_base = 0;
+
+	if (attr->exclude_idle)
+		return -EPERM;
+	if (attr->exclude_user)
+		config_base |= ARMV7_EXCLUDE_USER;
+	if (attr->exclude_kernel)
+		config_base |= ARMV7_EXCLUDE_PL1;
+	if (!attr->exclude_hv)
+		config_base |= ARMV7_INCLUDE_HYP;
+
+	/*
+	 * Install the filter into config_base as this is used to
+	 * construct the event type.
+	 */
+	event->config_base = config_base;
+
+	return 0;
 }
 
 static void armv7pmu_reset(void *info)
 {
-	u32 idx, nb_cnt = armpmu->num_events;
+	u32 idx, nb_cnt = cpu_pmu->num_events;
 
 	/* The counter and interrupt enable registers are unknown at reset. */
-	for (idx = 1; idx < nb_cnt; ++idx)
+	for (idx = ARMV7_IDX_CYCLE_COUNTER; idx < nb_cnt; ++idx)
 		armv7pmu_disable_event(NULL, idx);
 
 	/* Initialize & Reset PMNC: C and P bits */
 	armv7_pmnc_write(ARMV7_PMNC_P | ARMV7_PMNC_C);
 }
 
+static int armv7_a8_map_event(struct perf_event *event)
+{
+	return map_cpu_event(event, &armv7_a8_perf_map,
+				&armv7_a8_perf_cache_map, 0xFF);
+}
+
+static int armv7_a9_map_event(struct perf_event *event)
+{
+	return map_cpu_event(event, &armv7_a9_perf_map,
+				&armv7_a9_perf_cache_map, 0xFF);
+}
+
+static int armv7_a5_map_event(struct perf_event *event)
+{
+	return map_cpu_event(event, &armv7_a5_perf_map,
+				&armv7_a5_perf_cache_map, 0xFF);
+}
+
+static int armv7_a15_map_event(struct perf_event *event)
+{
+	return map_cpu_event(event, &armv7_a15_perf_map,
+				&armv7_a15_perf_cache_map, 0xFF);
+}
+
 static struct arm_pmu armv7pmu = {
 	.handle_irq		= armv7pmu_handle_irq,
 	.enable			= armv7pmu_enable_event,
@@ -1173,7 +1174,6 @@
 	.start			= armv7pmu_start,
 	.stop			= armv7pmu_stop,
 	.reset			= armv7pmu_reset,
-	.raw_event_mask		= 0xFF,
 	.max_period		= (1LLU << 32) - 1,
 };
 
@@ -1188,62 +1188,59 @@
 	return nb_cnt + 1;
 }
 
-static const struct arm_pmu *__init armv7_a8_pmu_init(void)
+static struct arm_pmu *__init armv7_a8_pmu_init(void)
 {
 	armv7pmu.id		= ARM_PERF_PMU_ID_CA8;
 	armv7pmu.name		= "ARMv7 Cortex-A8";
-	armv7pmu.cache_map	= &armv7_a8_perf_cache_map;
-	armv7pmu.event_map	= &armv7_a8_perf_map;
+	armv7pmu.map_event	= armv7_a8_map_event;
 	armv7pmu.num_events	= armv7_read_num_pmnc_events();
 	return &armv7pmu;
 }
 
-static const struct arm_pmu *__init armv7_a9_pmu_init(void)
+static struct arm_pmu *__init armv7_a9_pmu_init(void)
 {
 	armv7pmu.id		= ARM_PERF_PMU_ID_CA9;
 	armv7pmu.name		= "ARMv7 Cortex-A9";
-	armv7pmu.cache_map	= &armv7_a9_perf_cache_map;
-	armv7pmu.event_map	= &armv7_a9_perf_map;
+	armv7pmu.map_event	= armv7_a9_map_event;
 	armv7pmu.num_events	= armv7_read_num_pmnc_events();
 	return &armv7pmu;
 }
 
-static const struct arm_pmu *__init armv7_a5_pmu_init(void)
+static struct arm_pmu *__init armv7_a5_pmu_init(void)
 {
 	armv7pmu.id		= ARM_PERF_PMU_ID_CA5;
 	armv7pmu.name		= "ARMv7 Cortex-A5";
-	armv7pmu.cache_map	= &armv7_a5_perf_cache_map;
-	armv7pmu.event_map	= &armv7_a5_perf_map;
+	armv7pmu.map_event	= armv7_a5_map_event;
 	armv7pmu.num_events	= armv7_read_num_pmnc_events();
 	return &armv7pmu;
 }
 
-static const struct arm_pmu *__init armv7_a15_pmu_init(void)
+static struct arm_pmu *__init armv7_a15_pmu_init(void)
 {
 	armv7pmu.id		= ARM_PERF_PMU_ID_CA15;
 	armv7pmu.name		= "ARMv7 Cortex-A15";
-	armv7pmu.cache_map	= &armv7_a15_perf_cache_map;
-	armv7pmu.event_map	= &armv7_a15_perf_map;
+	armv7pmu.map_event	= armv7_a15_map_event;
 	armv7pmu.num_events	= armv7_read_num_pmnc_events();
+	armv7pmu.set_event_filter = armv7pmu_set_event_filter;
 	return &armv7pmu;
 }
 #else
-static const struct arm_pmu *__init armv7_a8_pmu_init(void)
+static struct arm_pmu *__init armv7_a8_pmu_init(void)
 {
 	return NULL;
 }
 
-static const struct arm_pmu *__init armv7_a9_pmu_init(void)
+static struct arm_pmu *__init armv7_a9_pmu_init(void)
 {
 	return NULL;
 }
 
-static const struct arm_pmu *__init armv7_a5_pmu_init(void)
+static struct arm_pmu *__init armv7_a5_pmu_init(void)
 {
 	return NULL;
 }
 
-static const struct arm_pmu *__init armv7_a15_pmu_init(void)
+static struct arm_pmu *__init armv7_a15_pmu_init(void)
 {
 	return NULL;
 }
diff --git a/arch/arm/kernel/perf_event_xscale.c b/arch/arm/kernel/perf_event_xscale.c
index 3c43974..e0cca10 100644
--- a/arch/arm/kernel/perf_event_xscale.c
+++ b/arch/arm/kernel/perf_event_xscale.c
@@ -40,7 +40,7 @@
 };
 
 enum xscale_counters {
-	XSCALE_CYCLE_COUNTER	= 1,
+	XSCALE_CYCLE_COUNTER	= 0,
 	XSCALE_COUNTER0,
 	XSCALE_COUNTER1,
 	XSCALE_COUNTER2,
@@ -222,7 +222,7 @@
 {
 	unsigned long pmnc;
 	struct perf_sample_data data;
-	struct cpu_hw_events *cpuc;
+	struct pmu_hw_events *cpuc;
 	struct pt_regs *regs;
 	int idx;
 
@@ -249,13 +249,10 @@
 	perf_sample_data_init(&data, 0);
 
 	cpuc = &__get_cpu_var(cpu_hw_events);
-	for (idx = 0; idx <= armpmu->num_events; ++idx) {
+	for (idx = 0; idx < cpu_pmu->num_events; ++idx) {
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		if (!test_bit(idx, cpuc->active_mask))
-			continue;
-
 		if (!xscale1_pmnc_counter_has_overflowed(pmnc, idx))
 			continue;
 
@@ -266,7 +263,7 @@
 			continue;
 
 		if (perf_event_overflow(event, &data, regs))
-			armpmu->disable(hwc, idx);
+			cpu_pmu->disable(hwc, idx);
 	}
 
 	irq_work_run();
@@ -284,6 +281,7 @@
 xscale1pmu_enable_event(struct hw_perf_event *hwc, int idx)
 {
 	unsigned long val, mask, evt, flags;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	switch (idx) {
 	case XSCALE_CYCLE_COUNTER:
@@ -305,18 +303,19 @@
 		return;
 	}
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	val = xscale1pmu_read_pmnc();
 	val &= ~mask;
 	val |= evt;
 	xscale1pmu_write_pmnc(val);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static void
 xscale1pmu_disable_event(struct hw_perf_event *hwc, int idx)
 {
 	unsigned long val, mask, evt, flags;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	switch (idx) {
 	case XSCALE_CYCLE_COUNTER:
@@ -336,16 +335,16 @@
 		return;
 	}
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	val = xscale1pmu_read_pmnc();
 	val &= ~mask;
 	val |= evt;
 	xscale1pmu_write_pmnc(val);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static int
-xscale1pmu_get_event_idx(struct cpu_hw_events *cpuc,
+xscale1pmu_get_event_idx(struct pmu_hw_events *cpuc,
 			struct hw_perf_event *event)
 {
 	if (XSCALE_PERFCTR_CCNT == event->config_base) {
@@ -368,24 +367,26 @@
 xscale1pmu_start(void)
 {
 	unsigned long flags, val;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	val = xscale1pmu_read_pmnc();
 	val |= XSCALE_PMU_ENABLE;
 	xscale1pmu_write_pmnc(val);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static void
 xscale1pmu_stop(void)
 {
 	unsigned long flags, val;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	val = xscale1pmu_read_pmnc();
 	val &= ~XSCALE_PMU_ENABLE;
 	xscale1pmu_write_pmnc(val);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static inline u32
@@ -424,7 +425,13 @@
 	}
 }
 
-static const struct arm_pmu xscale1pmu = {
+static int xscale_map_event(struct perf_event *event)
+{
+	return map_cpu_event(event, &xscale_perf_map,
+				&xscale_perf_cache_map, 0xFF);
+}
+
+static struct arm_pmu xscale1pmu = {
 	.id		= ARM_PERF_PMU_ID_XSCALE1,
 	.name		= "xscale1",
 	.handle_irq	= xscale1pmu_handle_irq,
@@ -435,14 +442,12 @@
 	.get_event_idx	= xscale1pmu_get_event_idx,
 	.start		= xscale1pmu_start,
 	.stop		= xscale1pmu_stop,
-	.cache_map	= &xscale_perf_cache_map,
-	.event_map	= &xscale_perf_map,
-	.raw_event_mask	= 0xFF,
+	.map_event	= xscale_map_event,
 	.num_events	= 3,
 	.max_period	= (1LLU << 32) - 1,
 };
 
-static const struct arm_pmu *__init xscale1pmu_init(void)
+static struct arm_pmu *__init xscale1pmu_init(void)
 {
 	return &xscale1pmu;
 }
@@ -560,7 +565,7 @@
 {
 	unsigned long pmnc, of_flags;
 	struct perf_sample_data data;
-	struct cpu_hw_events *cpuc;
+	struct pmu_hw_events *cpuc;
 	struct pt_regs *regs;
 	int idx;
 
@@ -581,13 +586,10 @@
 	perf_sample_data_init(&data, 0);
 
 	cpuc = &__get_cpu_var(cpu_hw_events);
-	for (idx = 0; idx <= armpmu->num_events; ++idx) {
+	for (idx = 0; idx < cpu_pmu->num_events; ++idx) {
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		if (!test_bit(idx, cpuc->active_mask))
-			continue;
-
 		if (!xscale2_pmnc_counter_has_overflowed(pmnc, idx))
 			continue;
 
@@ -598,7 +600,7 @@
 			continue;
 
 		if (perf_event_overflow(event, &data, regs))
-			armpmu->disable(hwc, idx);
+			cpu_pmu->disable(hwc, idx);
 	}
 
 	irq_work_run();
@@ -616,6 +618,7 @@
 xscale2pmu_enable_event(struct hw_perf_event *hwc, int idx)
 {
 	unsigned long flags, ien, evtsel;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	ien = xscale2pmu_read_int_enable();
 	evtsel = xscale2pmu_read_event_select();
@@ -649,16 +652,17 @@
 		return;
 	}
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	xscale2pmu_write_event_select(evtsel);
 	xscale2pmu_write_int_enable(ien);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static void
 xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx)
 {
 	unsigned long flags, ien, evtsel;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	ien = xscale2pmu_read_int_enable();
 	evtsel = xscale2pmu_read_event_select();
@@ -692,14 +696,14 @@
 		return;
 	}
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	xscale2pmu_write_event_select(evtsel);
 	xscale2pmu_write_int_enable(ien);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static int
-xscale2pmu_get_event_idx(struct cpu_hw_events *cpuc,
+xscale2pmu_get_event_idx(struct pmu_hw_events *cpuc,
 			struct hw_perf_event *event)
 {
 	int idx = xscale1pmu_get_event_idx(cpuc, event);
@@ -718,24 +722,26 @@
 xscale2pmu_start(void)
 {
 	unsigned long flags, val;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	val = xscale2pmu_read_pmnc() & ~XSCALE_PMU_CNT64;
 	val |= XSCALE_PMU_ENABLE;
 	xscale2pmu_write_pmnc(val);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static void
 xscale2pmu_stop(void)
 {
 	unsigned long flags, val;
+	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
-	raw_spin_lock_irqsave(&pmu_lock, flags);
+	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	val = xscale2pmu_read_pmnc();
 	val &= ~XSCALE_PMU_ENABLE;
 	xscale2pmu_write_pmnc(val);
-	raw_spin_unlock_irqrestore(&pmu_lock, flags);
+	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
 static inline u32
@@ -786,7 +792,7 @@
 	}
 }
 
-static const struct arm_pmu xscale2pmu = {
+static struct arm_pmu xscale2pmu = {
 	.id		= ARM_PERF_PMU_ID_XSCALE2,
 	.name		= "xscale2",
 	.handle_irq	= xscale2pmu_handle_irq,
@@ -797,24 +803,22 @@
 	.get_event_idx	= xscale2pmu_get_event_idx,
 	.start		= xscale2pmu_start,
 	.stop		= xscale2pmu_stop,
-	.cache_map	= &xscale_perf_cache_map,
-	.event_map	= &xscale_perf_map,
-	.raw_event_mask	= 0xFF,
+	.map_event	= xscale_map_event,
 	.num_events	= 5,
 	.max_period	= (1LLU << 32) - 1,
 };
 
-static const struct arm_pmu *__init xscale2pmu_init(void)
+static struct arm_pmu *__init xscale2pmu_init(void)
 {
 	return &xscale2pmu;
 }
 #else
-static const struct arm_pmu *__init xscale1pmu_init(void)
+static struct arm_pmu *__init xscale1pmu_init(void)
 {
 	return NULL;
 }
 
-static const struct arm_pmu *__init xscale2pmu_init(void)
+static struct arm_pmu *__init xscale2pmu_init(void)
 {
 	return NULL;
 }
diff --git a/arch/arm/kernel/pmu.c b/arch/arm/kernel/pmu.c
index c53474f..2c3407e 100644
--- a/arch/arm/kernel/pmu.c
+++ b/arch/arm/kernel/pmu.c
@@ -10,192 +10,26 @@
  *
  */
 
-#define pr_fmt(fmt) "PMU: " fmt
-
-#include <linux/cpumask.h>
 #include <linux/err.h>
-#include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
-#include <linux/of_device.h>
-#include <linux/platform_device.h>
 
 #include <asm/pmu.h>
 
-static volatile long pmu_lock;
+/*
+ * PMU locking to ensure mutual exclusion between different subsystems.
+ */
+static unsigned long pmu_lock[BITS_TO_LONGS(ARM_NUM_PMU_DEVICES)];
 
-static struct platform_device *pmu_devices[ARM_NUM_PMU_DEVICES];
-
-static int __devinit pmu_register(struct platform_device *pdev,
-					enum arm_pmu_type type)
-{
-	if (type < 0 || type >= ARM_NUM_PMU_DEVICES) {
-		pr_warning("received registration request for unknown "
-				"PMU device type %d\n", type);
-		return -EINVAL;
-	}
-
-	if (pmu_devices[type]) {
-		pr_warning("rejecting duplicate registration of PMU device "
-			"type %d.", type);
-		return -ENOSPC;
-	}
-
-	pr_info("registered new PMU device of type %d\n", type);
-	pmu_devices[type] = pdev;
-	return 0;
-}
-
-#define OF_MATCH_PMU(_name, _type) {	\
-	.compatible = _name,		\
-	.data = (void *)_type,		\
-}
-
-#define OF_MATCH_CPU(name)	OF_MATCH_PMU(name, ARM_PMU_DEVICE_CPU)
-
-static struct of_device_id armpmu_of_device_ids[] = {
-	OF_MATCH_CPU("arm,cortex-a9-pmu"),
-	OF_MATCH_CPU("arm,cortex-a8-pmu"),
-	OF_MATCH_CPU("arm,arm1136-pmu"),
-	OF_MATCH_CPU("arm,arm1176-pmu"),
-	{},
-};
-
-#define PLAT_MATCH_PMU(_name, _type) {	\
-	.name		= _name,	\
-	.driver_data	= _type,	\
-}
-
-#define PLAT_MATCH_CPU(_name)	PLAT_MATCH_PMU(_name, ARM_PMU_DEVICE_CPU)
-
-static struct platform_device_id armpmu_plat_device_ids[] = {
-	PLAT_MATCH_CPU("arm-pmu"),
-	{},
-};
-
-enum arm_pmu_type armpmu_device_type(struct platform_device *pdev)
-{
-	const struct of_device_id	*of_id;
-	const struct platform_device_id *pdev_id;
-
-	/* provided by of_device_id table */
-	if (pdev->dev.of_node) {
-		of_id = of_match_device(armpmu_of_device_ids, &pdev->dev);
-		BUG_ON(!of_id);
-		return (enum arm_pmu_type)of_id->data;
-	}
-
-	/* Provided by platform_device_id table */
-	pdev_id = platform_get_device_id(pdev);
-	BUG_ON(!pdev_id);
-	return pdev_id->driver_data;
-}
-
-static int __devinit armpmu_device_probe(struct platform_device *pdev)
-{
-	return pmu_register(pdev, armpmu_device_type(pdev));
-}
-
-static struct platform_driver armpmu_driver = {
-	.driver		= {
-		.name	= "arm-pmu",
-		.of_match_table = armpmu_of_device_ids,
-	},
-	.probe		= armpmu_device_probe,
-	.id_table	= armpmu_plat_device_ids,
-};
-
-static int __init register_pmu_driver(void)
-{
-	return platform_driver_register(&armpmu_driver);
-}
-device_initcall(register_pmu_driver);
-
-struct platform_device *
+int
 reserve_pmu(enum arm_pmu_type type)
 {
-	struct platform_device *pdev;
-
-	if (test_and_set_bit_lock(type, &pmu_lock)) {
-		pdev = ERR_PTR(-EBUSY);
-	} else if (pmu_devices[type] == NULL) {
-		clear_bit_unlock(type, &pmu_lock);
-		pdev = ERR_PTR(-ENODEV);
-	} else {
-		pdev = pmu_devices[type];
-	}
-
-	return pdev;
+	return test_and_set_bit_lock(type, pmu_lock) ? -EBUSY : 0;
 }
 EXPORT_SYMBOL_GPL(reserve_pmu);
 
-int
+void
 release_pmu(enum arm_pmu_type type)
 {
-	if (WARN_ON(!pmu_devices[type]))
-		return -EINVAL;
-	clear_bit_unlock(type, &pmu_lock);
-	return 0;
+	clear_bit_unlock(type, pmu_lock);
 }
-EXPORT_SYMBOL_GPL(release_pmu);
-
-static int
-set_irq_affinity(int irq,
-		 unsigned int cpu)
-{
-#ifdef CONFIG_SMP
-	int err = irq_set_affinity(irq, cpumask_of(cpu));
-	if (err)
-		pr_warning("unable to set irq affinity (irq=%d, cpu=%u)\n",
-			   irq, cpu);
-	return err;
-#else
-	return -EINVAL;
-#endif
-}
-
-static int
-init_cpu_pmu(void)
-{
-	int i, irqs, err = 0;
-	struct platform_device *pdev = pmu_devices[ARM_PMU_DEVICE_CPU];
-
-	if (!pdev)
-		return -ENODEV;
-
-	irqs = pdev->num_resources;
-
-	/*
-	 * If we have a single PMU interrupt that we can't shift, assume that
-	 * we're running on a uniprocessor machine and continue.
-	 */
-	if (irqs == 1 && !irq_can_set_affinity(platform_get_irq(pdev, 0)))
-		return 0;
-
-	for (i = 0; i < irqs; ++i) {
-		err = set_irq_affinity(platform_get_irq(pdev, i), i);
-		if (err)
-			break;
-	}
-
-	return err;
-}
-
-int
-init_pmu(enum arm_pmu_type type)
-{
-	int err = 0;
-
-	switch (type) {
-	case ARM_PMU_DEVICE_CPU:
-		err = init_cpu_pmu();
-		break;
-	default:
-		pr_warning("attempt to initialise PMU of unknown "
-			   "type %d\n", type);
-		err = -EINVAL;
-	}
-
-	return err;
-}
-EXPORT_SYMBOL_GPL(init_pmu);
diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c
index e514c76..6136144 100644
--- a/arch/arm/kernel/setup.c
+++ b/arch/arm/kernel/setup.c
@@ -820,25 +820,8 @@
 
 	if (__atags_pointer)
 		tags = phys_to_virt(__atags_pointer);
-	else if (mdesc->boot_params) {
-#ifdef CONFIG_MMU
-		/*
-		 * We still are executing with a minimal MMU mapping created
-		 * with the presumption that the machine default for this
-		 * is located in the first MB of RAM.  Anything else will
-		 * fault and silently hang the kernel at this point.
-		 */
-		if (mdesc->boot_params < PHYS_OFFSET ||
-		    mdesc->boot_params >= PHYS_OFFSET + SZ_1M) {
-			printk(KERN_WARNING
-			       "Default boot params at physical 0x%08lx out of reach\n",
-			       mdesc->boot_params);
-		} else
-#endif
-		{
-			tags = phys_to_virt(mdesc->boot_params);
-		}
-	}
+	else if (mdesc->atag_offset)
+		tags = (void *)(PAGE_OFFSET + mdesc->atag_offset);
 
 #if defined(CONFIG_DEPRECATED_PARAM_STRUCT)
 	/*
diff --git a/arch/arm/kernel/sleep.S b/arch/arm/kernel/sleep.S
index dc902f2..020e99c 100644
--- a/arch/arm/kernel/sleep.S
+++ b/arch/arm/kernel/sleep.S
@@ -8,92 +8,61 @@
 	.text
 
 /*
- * Save CPU state for a suspend
- *  r1 = v:p offset
- *  r2 = suspend function arg0
- *  r3 = suspend function
+ * Save CPU state for a suspend.  This saves the CPU general purpose
+ * registers, and allocates space on the kernel stack to save the CPU
+ * specific registers and some other data for resume.
+ *  r0 = suspend function arg0
+ *  r1 = suspend function
  */
 ENTRY(__cpu_suspend)
 	stmfd	sp!, {r4 - r11, lr}
 #ifdef MULTI_CPU
 	ldr	r10, =processor
-	ldr	r5, [r10, #CPU_SLEEP_SIZE] @ size of CPU sleep state
-	ldr	ip, [r10, #CPU_DO_RESUME] @ virtual resume function
+	ldr	r4, [r10, #CPU_SLEEP_SIZE] @ size of CPU sleep state
 #else
-	ldr	r5, =cpu_suspend_size
-	ldr	ip, =cpu_do_resume
+	ldr	r4, =cpu_suspend_size
 #endif
-	mov	r6, sp			@ current virtual SP
-	sub	sp, sp, r5		@ allocate CPU state on stack
-	mov	r0, sp			@ save pointer to CPU save block
-	add	ip, ip, r1		@ convert resume fn to phys
-	stmfd	sp!, {r1, r6, ip}	@ save v:p, virt SP, phys resume fn
-	ldr	r5, =sleep_save_sp
-	add	r6, sp, r1		@ convert SP to phys
-	stmfd	sp!, {r2, r3}		@ save suspend func arg and pointer
+	mov	r5, sp			@ current virtual SP
+	add	r4, r4, #12		@ Space for pgd, virt sp, phys resume fn
+	sub	sp, sp, r4		@ allocate CPU state on stack
+	stmfd	sp!, {r0, r1}		@ save suspend func arg and pointer
+	add	r0, sp, #8		@ save pointer to save block
+	mov	r1, r4			@ size of save block
+	mov	r2, r5			@ virtual SP
+	ldr	r3, =sleep_save_sp
 #ifdef CONFIG_SMP
 	ALT_SMP(mrc p15, 0, lr, c0, c0, 5)
 	ALT_UP(mov lr, #0)
 	and	lr, lr, #15
-	str	r6, [r5, lr, lsl #2]	@ save phys SP
-#else
-	str	r6, [r5]		@ save phys SP
+	add	r3, r3, lr, lsl #2
 #endif
-#ifdef MULTI_CPU
-	mov	lr, pc
-	ldr	pc, [r10, #CPU_DO_SUSPEND] @ save CPU state
-#else
-	bl	cpu_do_suspend
-#endif
-
-	@ flush data cache
-#ifdef MULTI_CACHE
-	ldr	r10, =cpu_cache
-	mov	lr, pc
-	ldr	pc, [r10, #CACHE_FLUSH_KERN_ALL]
-#else
-	bl	__cpuc_flush_kern_all
-#endif
+	bl	__cpu_suspend_save
 	adr	lr, BSYM(cpu_suspend_abort)
 	ldmfd	sp!, {r0, pc}		@ call suspend fn
 ENDPROC(__cpu_suspend)
 	.ltorg
 
 cpu_suspend_abort:
-	ldmia	sp!, {r1 - r3}		@ pop v:p, virt SP, phys resume fn
+	ldmia	sp!, {r1 - r3}		@ pop phys pgd, virt SP, phys resume fn
+	teq	r0, #0
+	moveq	r0, #1			@ force non-zero value
 	mov	sp, r2
 	ldmfd	sp!, {r4 - r11, pc}
 ENDPROC(cpu_suspend_abort)
 
 /*
  * r0 = control register value
- * r1 = v:p offset (preserved by cpu_do_resume)
- * r2 = phys page table base
- * r3 = L1 section flags
  */
-ENTRY(cpu_resume_mmu)
-	adr	r4, cpu_resume_turn_mmu_on
-	mov	r4, r4, lsr #20
-	orr	r3, r3, r4, lsl #20
-	ldr	r5, [r2, r4, lsl #2]	@ save old mapping
-	str	r3, [r2, r4, lsl #2]	@ setup 1:1 mapping for mmu code
-	sub	r2, r2, r1
-	ldr	r3, =cpu_resume_after_mmu
-	bic	r1, r0, #CR_C		@ ensure D-cache is disabled
-	b	cpu_resume_turn_mmu_on
-ENDPROC(cpu_resume_mmu)
-	.ltorg
 	.align	5
-cpu_resume_turn_mmu_on:
-	mcr	p15, 0, r1, c1, c0, 0	@ turn on MMU, I-cache, etc
-	mrc	p15, 0, r1, c0, c0, 0	@ read id reg
-	mov	r1, r1
-	mov	r1, r1
+ENTRY(cpu_resume_mmu)
+	ldr	r3, =cpu_resume_after_mmu
+	mcr	p15, 0, r0, c1, c0, 0	@ turn on MMU, I-cache, etc
+	mrc	p15, 0, r0, c0, c0, 0	@ read id reg
+	mov	r0, r0
+	mov	r0, r0
 	mov	pc, r3			@ jump to virtual address
-ENDPROC(cpu_resume_turn_mmu_on)
+ENDPROC(cpu_resume_mmu)
 cpu_resume_after_mmu:
-	str	r5, [r2, r4, lsl #2]	@ restore old mapping
-	mcr	p15, 0, r0, c1, c0, 0	@ turn on D-cache
 	bl	cpu_init		@ restore the und/abt/irq banked regs
 	mov	r0, #0			@ return zero on success
 	ldmfd	sp!, {r4 - r11, pc}
@@ -119,7 +88,7 @@
 	ldr	r0, sleep_save_sp	@ stack phys addr
 #endif
 	setmode	PSR_I_BIT | PSR_F_BIT | SVC_MODE, r1  @ set SVC, irqs off
-	@ load v:p, stack, resume fn
+	@ load phys pgd, stack, resume fn
   ARM(	ldmia	r0!, {r1, sp, pc}	)
 THUMB(	ldmia	r0!, {r1, r2, r3}	)
 THUMB(	mov	sp, r2			)
diff --git a/arch/arm/kernel/smp.c b/arch/arm/kernel/smp.c
index d88ff02..a96c08c 100644
--- a/arch/arm/kernel/smp.c
+++ b/arch/arm/kernel/smp.c
@@ -16,7 +16,6 @@
 #include <linux/cache.h>
 #include <linux/profile.h>
 #include <linux/errno.h>
-#include <linux/ftrace.h>
 #include <linux/mm.h>
 #include <linux/err.h>
 #include <linux/cpu.h>
@@ -31,6 +30,8 @@
 #include <asm/cacheflush.h>
 #include <asm/cpu.h>
 #include <asm/cputype.h>
+#include <asm/exception.h>
+#include <asm/topology.h>
 #include <asm/mmu_context.h>
 #include <asm/pgtable.h>
 #include <asm/pgalloc.h>
@@ -39,6 +40,7 @@
 #include <asm/tlbflush.h>
 #include <asm/ptrace.h>
 #include <asm/localtimer.h>
+#include <asm/smp_plat.h>
 
 /*
  * as from 2.5, kernels no longer have an init_tasks structure
@@ -259,6 +261,20 @@
 }
 #endif /* CONFIG_HOTPLUG_CPU */
 
+int __cpu_logical_map[NR_CPUS];
+
+void __init smp_setup_processor_id(void)
+{
+	int i;
+	u32 cpu = is_smp() ? read_cpuid_mpidr() & 0xff : 0;
+
+	cpu_logical_map(0) = cpu;
+	for (i = 1; i < NR_CPUS; ++i)
+		cpu_logical_map(i) = i == cpu ? 0 : i;
+
+	printk(KERN_INFO "Booting Linux on physical CPU %d\n", cpu);
+}
+
 /*
  * Called by both boot and secondaries to move global data into
  * per-processor storage.
@@ -268,6 +284,8 @@
 	struct cpuinfo_arm *cpu_info = &per_cpu(cpu_data, cpuid);
 
 	cpu_info->loops_per_jiffy = loops_per_jiffy;
+
+	store_cpu_topology(cpuid);
 }
 
 /*
@@ -358,6 +376,8 @@
 {
 	unsigned int ncores = num_possible_cpus();
 
+	init_cpu_topology();
+
 	smp_store_cpu_info(smp_processor_id());
 
 	/*
@@ -437,10 +457,6 @@
 	for (i = 0; i < NR_IPI; i++)
 		sum += __get_irq_stat(cpu, ipi_irqs[i]);
 
-#ifdef CONFIG_LOCAL_TIMERS
-	sum += __get_irq_stat(cpu, local_timer_irqs);
-#endif
-
 	return sum;
 }
 
@@ -457,33 +473,6 @@
 	irq_exit();
 }
 
-#ifdef CONFIG_LOCAL_TIMERS
-asmlinkage void __exception_irq_entry do_local_timer(struct pt_regs *regs)
-{
-	struct pt_regs *old_regs = set_irq_regs(regs);
-	int cpu = smp_processor_id();
-
-	if (local_timer_ack()) {
-		__inc_irq_stat(cpu, local_timer_irqs);
-		ipi_timer();
-	}
-
-	set_irq_regs(old_regs);
-}
-
-void show_local_irqs(struct seq_file *p, int prec)
-{
-	unsigned int cpu;
-
-	seq_printf(p, "%*s: ", prec, "LOC");
-
-	for_each_present_cpu(cpu)
-		seq_printf(p, "%10u ", __get_irq_stat(cpu, local_timer_irqs));
-
-	seq_printf(p, " Local timer interrupts\n");
-}
-#endif
-
 #ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST
 static void smp_timer_broadcast(const struct cpumask *mask)
 {
@@ -534,7 +523,7 @@
 	unsigned int cpu = smp_processor_id();
 	struct clock_event_device *evt = &per_cpu(percpu_clockevent, cpu);
 
-	evt->set_mode(CLOCK_EVT_MODE_UNUSED, evt);
+	local_timer_stop(evt);
 }
 #endif
 
@@ -567,6 +556,11 @@
  */
 asmlinkage void __exception_irq_entry do_IPI(int ipinr, struct pt_regs *regs)
 {
+	handle_IPI(ipinr, regs);
+}
+
+void handle_IPI(int ipinr, struct pt_regs *regs)
+{
 	unsigned int cpu = smp_processor_id();
 	struct pt_regs *old_regs = set_irq_regs(regs);
 
diff --git a/arch/arm/kernel/smp_scu.c b/arch/arm/kernel/smp_scu.c
index 7fcddb7..8f5dd79 100644
--- a/arch/arm/kernel/smp_scu.c
+++ b/arch/arm/kernel/smp_scu.c
@@ -34,7 +34,7 @@
 /*
  * Enable the SCU
  */
-void __init scu_enable(void __iomem *scu_base)
+void scu_enable(void __iomem *scu_base)
 {
 	u32 scu_ctrl;
 
diff --git a/arch/arm/kernel/smp_twd.c b/arch/arm/kernel/smp_twd.c
index 01c1862..a8a6682 100644
--- a/arch/arm/kernel/smp_twd.c
+++ b/arch/arm/kernel/smp_twd.c
@@ -19,6 +19,7 @@
 #include <linux/io.h>
 
 #include <asm/smp_twd.h>
+#include <asm/localtimer.h>
 #include <asm/hardware/gic.h>
 
 /* set up by the platform code */
@@ -26,6 +27,8 @@
 
 static unsigned long twd_timer_rate;
 
+static struct clock_event_device __percpu **twd_evt;
+
 static void twd_set_mode(enum clock_event_mode mode,
 			struct clock_event_device *clk)
 {
@@ -80,6 +83,12 @@
 	return 0;
 }
 
+void twd_timer_stop(struct clock_event_device *clk)
+{
+	twd_set_mode(CLOCK_EVT_MODE_UNUSED, clk);
+	disable_percpu_irq(clk->irq);
+}
+
 static void __cpuinit twd_calibrate_rate(void)
 {
 	unsigned long count;
@@ -119,11 +128,43 @@
 	}
 }
 
+static irqreturn_t twd_handler(int irq, void *dev_id)
+{
+	struct clock_event_device *evt = *(struct clock_event_device **)dev_id;
+
+	if (twd_timer_ack()) {
+		evt->event_handler(evt);
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
 /*
  * Setup the local clock events for a CPU.
  */
 void __cpuinit twd_timer_setup(struct clock_event_device *clk)
 {
+	struct clock_event_device **this_cpu_clk;
+
+	if (!twd_evt) {
+		int err;
+
+		twd_evt = alloc_percpu(struct clock_event_device *);
+		if (!twd_evt) {
+			pr_err("twd: can't allocate memory\n");
+			return;
+		}
+
+		err = request_percpu_irq(clk->irq, twd_handler,
+					 "twd", twd_evt);
+		if (err) {
+			pr_err("twd: can't register interrupt %d (%d)\n",
+			       clk->irq, err);
+			return;
+		}
+	}
+
 	twd_calibrate_rate();
 
 	clk->name = "local_timer";
@@ -137,8 +178,10 @@
 	clk->max_delta_ns = clockevent_delta2ns(0xffffffff, clk);
 	clk->min_delta_ns = clockevent_delta2ns(0xf, clk);
 
+	this_cpu_clk = __this_cpu_ptr(twd_evt);
+	*this_cpu_clk = clk;
+
 	clockevents_register_device(clk);
 
-	/* Make sure our local interrupt controller has this enabled */
-	gic_enable_ppi(clk->irq);
+	enable_percpu_irq(clk->irq, 0);
 }
diff --git a/arch/arm/kernel/suspend.c b/arch/arm/kernel/suspend.c
new file mode 100644
index 0000000..93a22d2
--- /dev/null
+++ b/arch/arm/kernel/suspend.c
@@ -0,0 +1,72 @@
+#include <linux/init.h>
+
+#include <asm/pgalloc.h>
+#include <asm/pgtable.h>
+#include <asm/memory.h>
+#include <asm/suspend.h>
+#include <asm/tlbflush.h>
+
+static pgd_t *suspend_pgd;
+
+extern int __cpu_suspend(unsigned long, int (*)(unsigned long));
+extern void cpu_resume_mmu(void);
+
+/*
+ * This is called by __cpu_suspend() to save the state, and do whatever
+ * flushing is required to ensure that when the CPU goes to sleep we have
+ * the necessary data available when the caches are not searched.
+ */
+void __cpu_suspend_save(u32 *ptr, u32 ptrsz, u32 sp, u32 *save_ptr)
+{
+	*save_ptr = virt_to_phys(ptr);
+
+	/* This must correspond to the LDM in cpu_resume() assembly */
+	*ptr++ = virt_to_phys(suspend_pgd);
+	*ptr++ = sp;
+	*ptr++ = virt_to_phys(cpu_do_resume);
+
+	cpu_do_suspend(ptr);
+
+	flush_cache_all();
+	outer_clean_range(*save_ptr, *save_ptr + ptrsz);
+	outer_clean_range(virt_to_phys(save_ptr),
+			  virt_to_phys(save_ptr) + sizeof(*save_ptr));
+}
+
+/*
+ * Hide the first two arguments to __cpu_suspend - these are an implementation
+ * detail which platform code shouldn't have to know about.
+ */
+int cpu_suspend(unsigned long arg, int (*fn)(unsigned long))
+{
+	struct mm_struct *mm = current->active_mm;
+	int ret;
+
+	if (!suspend_pgd)
+		return -EINVAL;
+
+	/*
+	 * Provide a temporary page table with an identity mapping for
+	 * the MMU-enable code, required for resuming.  On successful
+	 * resume (indicated by a zero return code), we need to switch
+	 * back to the correct page tables.
+	 */
+	ret = __cpu_suspend(arg, fn);
+	if (ret == 0) {
+		cpu_switch_mm(mm->pgd, mm);
+		local_flush_tlb_all();
+	}
+
+	return ret;
+}
+
+static int __init cpu_suspend_init(void)
+{
+	suspend_pgd = pgd_alloc(&init_mm);
+	if (suspend_pgd) {
+		unsigned long addr = virt_to_phys(cpu_resume_mmu);
+		identity_mapping_add(suspend_pgd, addr, addr + SECTION_SIZE);
+	}
+	return suspend_pgd ? 0 : -ENOMEM;
+}
+core_initcall(cpu_suspend_init);
diff --git a/arch/arm/kernel/topology.c b/arch/arm/kernel/topology.c
new file mode 100644
index 0000000..1040c00
--- /dev/null
+++ b/arch/arm/kernel/topology.c
@@ -0,0 +1,148 @@
+/*
+ * arch/arm/kernel/topology.c
+ *
+ * Copyright (C) 2011 Linaro Limited.
+ * Written by: Vincent Guittot
+ *
+ * based on arch/sh/kernel/topology.c
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/cpu.h>
+#include <linux/cpumask.h>
+#include <linux/init.h>
+#include <linux/percpu.h>
+#include <linux/node.h>
+#include <linux/nodemask.h>
+#include <linux/sched.h>
+
+#include <asm/cputype.h>
+#include <asm/topology.h>
+
+#define MPIDR_SMP_BITMASK (0x3 << 30)
+#define MPIDR_SMP_VALUE (0x2 << 30)
+
+#define MPIDR_MT_BITMASK (0x1 << 24)
+
+/*
+ * These masks reflect the current use of the affinity levels.
+ * The affinity level can be up to 16 bits according to ARM ARM
+ */
+
+#define MPIDR_LEVEL0_MASK 0x3
+#define MPIDR_LEVEL0_SHIFT 0
+
+#define MPIDR_LEVEL1_MASK 0xF
+#define MPIDR_LEVEL1_SHIFT 8
+
+#define MPIDR_LEVEL2_MASK 0xFF
+#define MPIDR_LEVEL2_SHIFT 16
+
+struct cputopo_arm cpu_topology[NR_CPUS];
+
+const struct cpumask *cpu_coregroup_mask(unsigned int cpu)
+{
+	return &cpu_topology[cpu].core_sibling;
+}
+
+/*
+ * store_cpu_topology is called at boot when only one cpu is running
+ * and with the mutex cpu_hotplug.lock locked, when several cpus have booted,
+ * which prevents simultaneous write access to cpu_topology array
+ */
+void store_cpu_topology(unsigned int cpuid)
+{
+	struct cputopo_arm *cpuid_topo = &cpu_topology[cpuid];
+	unsigned int mpidr;
+	unsigned int cpu;
+
+	/* If the cpu topology has been already set, just return */
+	if (cpuid_topo->core_id != -1)
+		return;
+
+	mpidr = read_cpuid_mpidr();
+
+	/* create cpu topology mapping */
+	if ((mpidr & MPIDR_SMP_BITMASK) == MPIDR_SMP_VALUE) {
+		/*
+		 * This is a multiprocessor system
+		 * multiprocessor format & multiprocessor mode field are set
+		 */
+
+		if (mpidr & MPIDR_MT_BITMASK) {
+			/* core performance interdependency */
+			cpuid_topo->thread_id = (mpidr >> MPIDR_LEVEL0_SHIFT)
+				& MPIDR_LEVEL0_MASK;
+			cpuid_topo->core_id = (mpidr >> MPIDR_LEVEL1_SHIFT)
+				& MPIDR_LEVEL1_MASK;
+			cpuid_topo->socket_id = (mpidr >> MPIDR_LEVEL2_SHIFT)
+				& MPIDR_LEVEL2_MASK;
+		} else {
+			/* largely independent cores */
+			cpuid_topo->thread_id = -1;
+			cpuid_topo->core_id = (mpidr >> MPIDR_LEVEL0_SHIFT)
+				& MPIDR_LEVEL0_MASK;
+			cpuid_topo->socket_id = (mpidr >> MPIDR_LEVEL1_SHIFT)
+				& MPIDR_LEVEL1_MASK;
+		}
+	} else {
+		/*
+		 * This is an uniprocessor system
+		 * we are in multiprocessor format but uniprocessor system
+		 * or in the old uniprocessor format
+		 */
+		cpuid_topo->thread_id = -1;
+		cpuid_topo->core_id = 0;
+		cpuid_topo->socket_id = -1;
+	}
+
+	/* update core and thread sibling masks */
+	for_each_possible_cpu(cpu) {
+		struct cputopo_arm *cpu_topo = &cpu_topology[cpu];
+
+		if (cpuid_topo->socket_id == cpu_topo->socket_id) {
+			cpumask_set_cpu(cpuid, &cpu_topo->core_sibling);
+			if (cpu != cpuid)
+				cpumask_set_cpu(cpu,
+					&cpuid_topo->core_sibling);
+
+			if (cpuid_topo->core_id == cpu_topo->core_id) {
+				cpumask_set_cpu(cpuid,
+					&cpu_topo->thread_sibling);
+				if (cpu != cpuid)
+					cpumask_set_cpu(cpu,
+						&cpuid_topo->thread_sibling);
+			}
+		}
+	}
+	smp_wmb();
+
+	printk(KERN_INFO "CPU%u: thread %d, cpu %d, socket %d, mpidr %x\n",
+		cpuid, cpu_topology[cpuid].thread_id,
+		cpu_topology[cpuid].core_id,
+		cpu_topology[cpuid].socket_id, mpidr);
+}
+
+/*
+ * init_cpu_topology is called at boot when only one cpu is running
+ * which prevent simultaneous write access to cpu_topology array
+ */
+void init_cpu_topology(void)
+{
+	unsigned int cpu;
+
+	/* init core mask */
+	for_each_possible_cpu(cpu) {
+		struct cputopo_arm *cpu_topo = &(cpu_topology[cpu]);
+
+		cpu_topo->thread_id = -1;
+		cpu_topo->core_id =  -1;
+		cpu_topo->socket_id = -1;
+		cpumask_clear(&cpu_topo->core_sibling);
+		cpumask_clear(&cpu_topo->thread_sibling);
+	}
+	smp_wmb();
+}
diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c
index bc9f9da..2103825 100644
--- a/arch/arm/kernel/traps.c
+++ b/arch/arm/kernel/traps.c
@@ -27,6 +27,7 @@
 
 #include <linux/atomic.h>
 #include <asm/cacheflush.h>
+#include <asm/exception.h>
 #include <asm/system.h>
 #include <asm/unistd.h>
 #include <asm/traps.h>
diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c
index e04c5fb..1532b50 100644
--- a/arch/arm/mach-at91/at91sam9g45.c
+++ b/arch/arm/mach-at91/at91sam9g45.c
@@ -12,6 +12,7 @@
 
 #include <linux/module.h>
 #include <linux/pm.h>
+#include <linux/dma-mapping.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -319,6 +320,7 @@
 static void __init at91sam9g45_map_io(void)
 {
 	at91_init_sram(0, AT91SAM9G45_SRAM_BASE, AT91SAM9G45_SRAM_SIZE);
+	init_consistent_dma_size(SZ_4M);
 }
 
 static void __init at91sam9g45_initialize(void)
diff --git a/arch/arm/mach-at91/include/mach/at91sam9g45.h b/arch/arm/mach-at91/include/mach/at91sam9g45.h
index 2c611b9..406bb64 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9g45.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9g45.h
@@ -128,8 +128,6 @@
 #define AT91SAM9G45_EHCI_BASE	0x00800000	/* USB Host controller (EHCI) */
 #define AT91SAM9G45_VDEC_BASE	0x00900000	/* Video Decoder Controller */
 
-#define CONSISTENT_DMA_SIZE	SZ_4M
-
 /*
  * DMA peripheral identifiers
  * for hardware handshaking interface
diff --git a/arch/arm/mach-at91/include/mach/debug-macro.S b/arch/arm/mach-at91/include/mach/debug-macro.S
index bc1e0b2..0ed8648 100644
--- a/arch/arm/mach-at91/include/mach/debug-macro.S
+++ b/arch/arm/mach-at91/include/mach/debug-macro.S
@@ -14,7 +14,7 @@
 #include <mach/hardware.h>
 #include <mach/at91_dbgu.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =(AT91_BASE_SYS + AT91_DBGU)	@ System peripherals (phys address)
 	ldr	\rv, =(AT91_VA_BASE_SYS	+ AT91_DBGU)	@ System peripherals (virt address)
 	.endm
diff --git a/arch/arm/mach-bcmring/include/mach/hardware.h b/arch/arm/mach-bcmring/include/mach/hardware.h
index ed78aab..6ae20a6 100644
--- a/arch/arm/mach-bcmring/include/mach/hardware.h
+++ b/arch/arm/mach-bcmring/include/mach/hardware.h
@@ -22,7 +22,6 @@
 #define __ASM_ARCH_HARDWARE_H
 
 #include <asm/sizes.h>
-#include <mach/memory.h>
 #include <cfg_global.h>
 #include <mach/csp/mm_io.h>
 
@@ -31,7 +30,7 @@
  *  *_SIZE  is the size of the region
  *  *_BASE  is the virtual address
  */
-#define RAM_START               PLAT_PHYS_OFFSET
+#define RAM_START               PHYS_OFFSET
 
 #define RAM_SIZE                (CFG_GLOBAL_RAM_SIZE-CFG_GLOBAL_RAM_SIZE_RESERVED)
 #define RAM_BASE                PAGE_OFFSET
diff --git a/arch/arm/mach-bcmring/include/mach/memory.h b/arch/arm/mach-bcmring/include/mach/memory.h
deleted file mode 100644
index 15162e4..0000000
--- a/arch/arm/mach-bcmring/include/mach/memory.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*****************************************************************************
-* Copyright 2005 - 2008 Broadcom Corporation.  All rights reserved.
-*
-* Unless you and Broadcom execute a separate written software license
-* agreement governing use of this software, this software is licensed to you
-* under the terms of the GNU General Public License version 2, available at
-* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-*
-* Notwithstanding the above, under no circumstances may you combine this
-* software in any way with any other Broadcom software provided under a
-* license other than the GPL, without Broadcom's express prior written
-* consent.
-*****************************************************************************/
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#include <cfg_global.h>
-
-/*
- * Physical vs virtual RAM address space conversion.  These are
- * private definitions which should NOT be used outside memory.h
- * files.  Use virt_to_phys/phys_to_virt/__pa/__va instead.
- */
-
-#define PLAT_PHYS_OFFSET CFG_GLOBAL_RAM_BASE
-
-/*
- * Maximum DMA memory allowed is 14M
- */
-#define CONSISTENT_DMA_SIZE (SZ_16M - SZ_2M)
-
-#endif
diff --git a/arch/arm/mach-bcmring/mm.c b/arch/arm/mach-bcmring/mm.c
index 0f1c37e..8616876 100644
--- a/arch/arm/mach-bcmring/mm.c
+++ b/arch/arm/mach-bcmring/mm.c
@@ -13,6 +13,7 @@
 *****************************************************************************/
 
 #include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
 #include <asm/mach/map.h>
 
 #include <mach/hardware.h>
@@ -53,4 +54,6 @@
 {
 
 	iotable_init(bcmring_io_desc, ARRAY_SIZE(bcmring_io_desc));
+	/* Maximum DMA memory allowed is 14M */
+	init_consistent_dma_size(14 << 20);
 }
diff --git a/arch/arm/mach-clps711x/autcpu12.c b/arch/arm/mach-clps711x/autcpu12.c
index 4a74b2c9..0276091 100644
--- a/arch/arm/mach-clps711x/autcpu12.c
+++ b/arch/arm/mach-clps711x/autcpu12.c
@@ -64,7 +64,7 @@
 
 MACHINE_START(AUTCPU12, "autronix autcpu12")
 	/* Maintainer: Thomas Gleixner */
-	.boot_params	= 0xc0020000,
+	.atag_offset	= 0x20000,
 	.map_io		= autcpu12_map_io,
 	.init_irq	= clps711x_init_irq,
 	.timer		= &clps711x_timer,
diff --git a/arch/arm/mach-clps711x/cdb89712.c b/arch/arm/mach-clps711x/cdb89712.c
index 5a1689d..25b3bfd 100644
--- a/arch/arm/mach-clps711x/cdb89712.c
+++ b/arch/arm/mach-clps711x/cdb89712.c
@@ -55,7 +55,7 @@
 
 MACHINE_START(CDB89712, "Cirrus-CDB89712")
 	/* Maintainer: Ray Lehtiniemi */
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= cdb89712_map_io,
 	.init_irq	= clps711x_init_irq,
 	.timer		= &clps711x_timer,
diff --git a/arch/arm/mach-clps711x/ceiva.c b/arch/arm/mach-clps711x/ceiva.c
index 16481cf..1df9ec6 100644
--- a/arch/arm/mach-clps711x/ceiva.c
+++ b/arch/arm/mach-clps711x/ceiva.c
@@ -56,7 +56,7 @@
 
 MACHINE_START(CEIVA, "CEIVA/Polaroid Photo MAX Digital Picture Frame")
 	/* Maintainer: Rob Scott */
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= ceiva_map_io,
 	.init_irq	= clps711x_init_irq,
 	.timer		= &clps711x_timer,
diff --git a/arch/arm/mach-clps711x/clep7312.c b/arch/arm/mach-clps711x/clep7312.c
index 67b5abb4..06c8abd 100644
--- a/arch/arm/mach-clps711x/clep7312.c
+++ b/arch/arm/mach-clps711x/clep7312.c
@@ -37,7 +37,7 @@
 
 MACHINE_START(CLEP7212, "Cirrus Logic 7212/7312")
 	/* Maintainer: Nobody */
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x0100,
 	.fixup		= fixup_clep7312,
 	.map_io		= clps711x_map_io,
 	.init_irq	= clps711x_init_irq,
diff --git a/arch/arm/mach-clps711x/edb7211-arch.c b/arch/arm/mach-clps711x/edb7211-arch.c
index 98ca5b2..abf522d 100644
--- a/arch/arm/mach-clps711x/edb7211-arch.c
+++ b/arch/arm/mach-clps711x/edb7211-arch.c
@@ -57,7 +57,7 @@
 
 MACHINE_START(EDB7211, "CL-EDB7211 (EP7211 eval board)")
 	/* Maintainer: Jon McClintock */
-	.boot_params	= 0xc0020100,	/* 0xc0000000 - 0xc001ffff can be video RAM */
+	.atag_offset	= 0x20100,	/* 0xc0000000 - 0xc001ffff can be video RAM */
 	.fixup		= fixup_edb7211,
 	.map_io		= edb7211_map_io,
 	.reserve	= edb7211_reserve,
diff --git a/arch/arm/mach-clps711x/fortunet.c b/arch/arm/mach-clps711x/fortunet.c
index b1cb479..b6f7d86 100644
--- a/arch/arm/mach-clps711x/fortunet.c
+++ b/arch/arm/mach-clps711x/fortunet.c
@@ -75,7 +75,6 @@
 
 MACHINE_START(FORTUNET, "ARM-FortuNet")
 	/* Maintainer: FortuNet Inc. */
-	.boot_params	= 0x00000000,
 	.fixup		= fortunet_fixup,
 	.map_io		= clps711x_map_io,
 	.init_irq	= clps711x_init_irq,
diff --git a/arch/arm/mach-clps711x/include/mach/debug-macro.S b/arch/arm/mach-clps711x/include/mach/debug-macro.S
index 507c687..b802e8a 100644
--- a/arch/arm/mach-clps711x/include/mach/debug-macro.S
+++ b/arch/arm/mach-clps711x/include/mach/debug-macro.S
@@ -14,7 +14,7 @@
 #include <mach/hardware.h>
 #include <asm/hardware/clps7111.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 #ifndef CONFIG_DEBUG_CLPS711X_UART2
 		mov	\rp, #0x0000	@ UART1
 #else
diff --git a/arch/arm/mach-clps711x/p720t.c b/arch/arm/mach-clps711x/p720t.c
index cefbce0..e7f75ae 100644
--- a/arch/arm/mach-clps711x/p720t.c
+++ b/arch/arm/mach-clps711x/p720t.c
@@ -89,7 +89,7 @@
 
 MACHINE_START(P720T, "ARM-Prospector720T")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.fixup		= fixup_p720t,
 	.map_io		= p720t_map_io,
 	.init_irq	= clps711x_init_irq,
diff --git a/arch/arm/mach-cns3xxx/cns3420vb.c b/arch/arm/mach-cns3xxx/cns3420vb.c
index 3e7d149..55f7b4b 100644
--- a/arch/arm/mach-cns3xxx/cns3420vb.c
+++ b/arch/arm/mach-cns3xxx/cns3420vb.c
@@ -197,7 +197,7 @@
 }
 
 MACHINE_START(CNS3420VB, "Cavium Networks CNS3420 Validation Board")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= cns3420_map_io,
 	.init_irq	= cns3xxx_init_irq,
 	.timer		= &cns3xxx_timer,
diff --git a/arch/arm/mach-cns3xxx/include/mach/debug-macro.S b/arch/arm/mach-cns3xxx/include/mach/debug-macro.S
index 56d8286..d04c150 100644
--- a/arch/arm/mach-cns3xxx/include/mach/debug-macro.S
+++ b/arch/arm/mach-cns3xxx/include/mach/debug-macro.S
@@ -10,7 +10,7 @@
  * published by the Free Software Foundation.
  */
 
-		.macro	addruart,rp,rv
+		.macro	addruart,rp,rv,tmp
 		mov	\rp, #0x00009000
 		orr	\rv, \rp, #0xf0000000	@ virtual base
 		orr	\rp, \rp, #0x10000000
diff --git a/arch/arm/mach-cns3xxx/include/mach/memory.h b/arch/arm/mach-cns3xxx/include/mach/memory.h
deleted file mode 100644
index dc16c5c..0000000
--- a/arch/arm/mach-cns3xxx/include/mach/memory.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * Copyright 2003 ARM Limited
- * Copyright 2008 Cavium Networks
- *
- * This file is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License, Version 2, as
- * published by the Free Software Foundation.
- */
-
-#ifndef __MACH_MEMORY_H
-#define __MACH_MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET		UL(0x00000000)
-
-#define __phys_to_bus(x)	((x) + PHYS_OFFSET)
-#define __bus_to_phys(x)	((x) - PHYS_OFFSET)
-
-#define __virt_to_bus(v)	__phys_to_bus(__virt_to_phys(v))
-#define __bus_to_virt(b)	__phys_to_virt(__bus_to_phys(b))
-#define __pfn_to_bus(p)		__phys_to_bus(__pfn_to_phys(p))
-#define __bus_to_pfn(b)		__phys_to_pfn(__bus_to_phys(b))
-
-#endif
diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c
index 84fd786..26d94c0 100644
--- a/arch/arm/mach-davinci/board-da830-evm.c
+++ b/arch/arm/mach-davinci/board-da830-evm.c
@@ -676,7 +676,7 @@
 }
 
 MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137/AM17x EVM")
-	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		= da830_evm_map_io,
 	.init_irq	= cp_intc_init,
 	.timer		= &davinci_timer,
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index 008d514..6e41cb5 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -1291,7 +1291,7 @@
 }
 
 MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138/AM18x EVM")
-	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		= da850_evm_map_io,
 	.init_irq	= cp_intc_init,
 	.timer		= &davinci_timer,
diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c
index 241a6bd..6556628 100644
--- a/arch/arm/mach-davinci/board-dm355-evm.c
+++ b/arch/arm/mach-davinci/board-dm355-evm.c
@@ -351,7 +351,7 @@
 }
 
 MACHINE_START(DAVINCI_DM355_EVM, "DaVinci DM355 EVM")
-	.boot_params  = (0x80000100),
+	.atag_offset  = 0x100,
 	.map_io	      = dm355_evm_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer	      = &davinci_timer,
diff --git a/arch/arm/mach-davinci/board-dm355-leopard.c b/arch/arm/mach-davinci/board-dm355-leopard.c
index bee284c..b307470 100644
--- a/arch/arm/mach-davinci/board-dm355-leopard.c
+++ b/arch/arm/mach-davinci/board-dm355-leopard.c
@@ -270,7 +270,7 @@
 }
 
 MACHINE_START(DM355_LEOPARD, "DaVinci DM355 leopard")
-	.boot_params  = (0x80000100),
+	.atag_offset  = 0x100,
 	.map_io	      = dm355_leopard_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer	      = &davinci_timer,
diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c
index 9818f21..04c43ab 100644
--- a/arch/arm/mach-davinci/board-dm365-evm.c
+++ b/arch/arm/mach-davinci/board-dm365-evm.c
@@ -612,7 +612,7 @@
 }
 
 MACHINE_START(DAVINCI_DM365_EVM, "DaVinci DM365 EVM")
-	.boot_params	= (0x80000100),
+	.atag_offset	= 0x100,
 	.map_io		= dm365_evm_map_io,
 	.init_irq	= davinci_irq_init,
 	.timer		= &davinci_timer,
diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c
index 95607a1..a005e769 100644
--- a/arch/arm/mach-davinci/board-dm644x-evm.c
+++ b/arch/arm/mach-davinci/board-dm644x-evm.c
@@ -712,7 +712,7 @@
 
 MACHINE_START(DAVINCI_EVM, "DaVinci DM644x EVM")
 	/* Maintainer: MontaVista Software <source@mvista.com> */
-	.boot_params  = (DAVINCI_DDR_BASE + 0x100),
+	.atag_offset  = 0x100,
 	.map_io	      = davinci_evm_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer	      = &davinci_timer,
diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c
index 993a3146..337c45e 100644
--- a/arch/arm/mach-davinci/board-dm646x-evm.c
+++ b/arch/arm/mach-davinci/board-dm646x-evm.c
@@ -792,7 +792,7 @@
 }
 
 MACHINE_START(DAVINCI_DM6467_EVM, "DaVinci DM646x EVM")
-	.boot_params  = (0x80000100),
+	.atag_offset  = 0x100,
 	.map_io       = davinci_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer        = &davinci_timer,
@@ -801,7 +801,7 @@
 MACHINE_END
 
 MACHINE_START(DAVINCI_DM6467TEVM, "DaVinci DM6467T EVM")
-	.boot_params  = (0x80000100),
+	.atag_offset  = 0x100,
 	.map_io       = davinci_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer        = &davinci_timer,
diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c
index c278226..6efc84cc 100644
--- a/arch/arm/mach-davinci/board-mityomapl138.c
+++ b/arch/arm/mach-davinci/board-mityomapl138.c
@@ -566,7 +566,7 @@
 }
 
 MACHINE_START(MITYOMAPL138, "MityDSP-L138/MityARM-1808")
-	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		= mityomapl138_map_io,
 	.init_irq	= cp_intc_init,
 	.timer		= &davinci_timer,
diff --git a/arch/arm/mach-davinci/board-neuros-osd2.c b/arch/arm/mach-davinci/board-neuros-osd2.c
index d60a800..38d6f64 100644
--- a/arch/arm/mach-davinci/board-neuros-osd2.c
+++ b/arch/arm/mach-davinci/board-neuros-osd2.c
@@ -272,7 +272,7 @@
 
 MACHINE_START(NEUROS_OSD2, "Neuros OSD2")
 	/* Maintainer: Neuros Technologies <neuros@groups.google.com> */
-	.boot_params	= (DAVINCI_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		 = davinci_ntosd2_map_io,
 	.init_irq	= davinci_irq_init,
 	.timer		= &davinci_timer,
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
index 237332a..c6701e4 100644
--- a/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -338,7 +338,7 @@
 }
 
 MACHINE_START(OMAPL138_HAWKBOARD, "AM18x/OMAP-L138 Hawkboard")
-	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		= omapl138_hawk_map_io,
 	.init_irq	= cp_intc_init,
 	.timer		= &davinci_timer,
diff --git a/arch/arm/mach-davinci/board-sffsdr.c b/arch/arm/mach-davinci/board-sffsdr.c
index 5f4385c..5dd4da9 100644
--- a/arch/arm/mach-davinci/board-sffsdr.c
+++ b/arch/arm/mach-davinci/board-sffsdr.c
@@ -151,7 +151,7 @@
 
 MACHINE_START(SFFSDR, "Lyrtech SFFSDR")
 	/* Maintainer: Hugo Villeneuve hugo.villeneuve@lyrtech.com */
-	.boot_params  = (DAVINCI_DDR_BASE + 0x100),
+	.atag_offset  = 0x100,
 	.map_io	      = davinci_sffsdr_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer	      = &davinci_timer,
diff --git a/arch/arm/mach-davinci/board-tnetv107x-evm.c b/arch/arm/mach-davinci/board-tnetv107x-evm.c
index 7828920..90ee7b5 100644
--- a/arch/arm/mach-davinci/board-tnetv107x-evm.c
+++ b/arch/arm/mach-davinci/board-tnetv107x-evm.c
@@ -277,7 +277,7 @@
 #endif
 
 MACHINE_START(TNETV107X, "TNETV107X EVM")
-	.boot_params	= (TNETV107X_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		= tnetv107x_init,
 	.init_irq	= cp_intc_init,
 	.timer		= &davinci_timer,
diff --git a/arch/arm/mach-davinci/common.c b/arch/arm/mach-davinci/common.c
index 1d25573..865ffe5 100644
--- a/arch/arm/mach-davinci/common.c
+++ b/arch/arm/mach-davinci/common.c
@@ -12,6 +12,7 @@
 #include <linux/io.h>
 #include <linux/etherdevice.h>
 #include <linux/davinci_emac.h>
+#include <linux/dma-mapping.h>
 
 #include <asm/tlb.h>
 #include <asm/mach/map.h>
@@ -86,6 +87,8 @@
 		iotable_init(davinci_soc_info.io_desc,
 				davinci_soc_info.io_desc_num);
 
+	init_consistent_dma_size(14 << 20);
+
 	/*
 	 * Normally devicemaps_init() would flush caches and tlb after
 	 * mdesc->map_io(), but we must also do it here because of the CPU
diff --git a/arch/arm/mach-davinci/cpuidle.c b/arch/arm/mach-davinci/cpuidle.c
index bd59f31..0b314bf 100644
--- a/arch/arm/mach-davinci/cpuidle.c
+++ b/arch/arm/mach-davinci/cpuidle.c
@@ -19,7 +19,7 @@
 #include <asm/proc-fns.h>
 
 #include <mach/cpuidle.h>
-#include <mach/memory.h>
+#include <mach/ddr2.h>
 
 #define DAVINCI_CPUIDLE_MAX_STATES	2
 
diff --git a/arch/arm/mach-davinci/include/mach/ddr2.h b/arch/arm/mach-davinci/include/mach/ddr2.h
new file mode 100644
index 0000000..c19e047
--- /dev/null
+++ b/arch/arm/mach-davinci/include/mach/ddr2.h
@@ -0,0 +1,4 @@
+#define DDR2_SDRCR_OFFSET	0xc
+#define DDR2_SRPD_BIT		(1 << 23)
+#define DDR2_MCLKSTOPEN_BIT	(1 << 30)
+#define DDR2_LPMODEN_BIT	(1 << 31)
diff --git a/arch/arm/mach-davinci/include/mach/debug-macro.S b/arch/arm/mach-davinci/include/mach/debug-macro.S
index f8b7ea4..cf94552 100644
--- a/arch/arm/mach-davinci/include/mach/debug-macro.S
+++ b/arch/arm/mach-davinci/include/mach/debug-macro.S
@@ -18,56 +18,50 @@
 
 #include <linux/serial_reg.h>
 
-#include <asm/memory.h>
-
 #include <mach/serial.h>
 
 #define UART_SHIFT	2
 
-#define davinci_uart_v2p(x)	((x) - PAGE_OFFSET + PLAT_PHYS_OFFSET)
-#define davinci_uart_p2v(x)	((x) - PLAT_PHYS_OFFSET + PAGE_OFFSET)
-
 		.pushsection .data
 davinci_uart_phys:	.word	0
 davinci_uart_virt:	.word	0
 		.popsection
 
-		.macro addruart, rp, rv
+		.macro addruart, rp, rv, tmp
 
 		/* Use davinci_uart_phys/virt if already configured */
-10:		mrc	p15, 0, \rp, c1, c0
-		tst	\rp, #1			@ MMU enabled?
-		ldreq	\rp, =davinci_uart_v2p(davinci_uart_phys)
-		ldrne	\rp, =davinci_uart_phys
-		add	\rv, \rp, #4		@ davinci_uart_virt
-		ldr	\rp, [\rp, #0]
-		ldr	\rv, [\rv, #0]
+10:		adr	\rp, 99f		@ get effective addr of 99f
+		ldr	\rv, [\rp]		@ get absolute addr of 99f
+		sub	\rv, \rv, \rp		@ offset between the two
+		ldr	\rp, [\rp, #4]		@ abs addr of omap_uart_phys
+		sub	\tmp, \rp, \rv		@ make it effective
+		ldr	\rp, [\tmp, #0]		@ davinci_uart_phys
+		ldr	\rv, [\tmp, #4]		@ davinci_uart_virt
 		cmp	\rp, #0			@ is port configured?
 		cmpne	\rv, #0
-		bne	99f			@ already configured
+		bne	100f			@ already configured
 
 		/* Check the debug UART address set in uncompress.h */
-		mrc	p15, 0, \rp, c1, c0
-		tst	\rp, #1			@ MMU enabled?
+		and	\rp, pc, #0xff000000
+		ldr	\rv, =DAVINCI_UART_INFO_OFS
+		add	\rp, \rp, \rv
 
 		/* Copy uart phys address from decompressor uart info */
-		ldreq	\rv, =davinci_uart_v2p(davinci_uart_phys)
-		ldrne	\rv, =davinci_uart_phys
-		ldreq	\rp, =DAVINCI_UART_INFO
-		ldrne	\rp, =davinci_uart_p2v(DAVINCI_UART_INFO)
-		ldr	\rp, [\rp, #0]
-		str	\rp, [\rv]
+		ldr	\rv, [\rp, #0]
+		str	\rv, [\tmp, #0]
 
 		/* Copy uart virt address from decompressor uart info */
-		ldreq	\rv, =davinci_uart_v2p(davinci_uart_virt)
-		ldrne	\rv, =davinci_uart_virt
-		ldreq	\rp, =DAVINCI_UART_INFO
-		ldrne	\rp, =davinci_uart_p2v(DAVINCI_UART_INFO)
-		ldr	\rp, [\rp, #4]
-		str	\rp, [\rv]
+		ldr	\rv, [\rp, #4]
+		str	\rv, [\tmp, #4]
 
 		b	10b
-99:
+
+		.align
+99:		.word	.
+		.word	davinci_uart_phys
+		.ltorg
+
+100:
 		.endm
 
 		.macro	senduart,rd,rx
diff --git a/arch/arm/mach-davinci/include/mach/memory.h b/arch/arm/mach-davinci/include/mach/memory.h
deleted file mode 100644
index 7873194..0000000
--- a/arch/arm/mach-davinci/include/mach/memory.h
+++ /dev/null
@@ -1,44 +0,0 @@
-/*
- * DaVinci memory space definitions
- *
- * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
- *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/**************************************************************************
- * Included Files
- **************************************************************************/
-#include <asm/page.h>
-#include <asm/sizes.h>
-
-/**************************************************************************
- * Definitions
- **************************************************************************/
-#define DAVINCI_DDR_BASE	0x80000000
-#define DA8XX_DDR_BASE		0xc0000000
-
-#if defined(CONFIG_ARCH_DAVINCI_DA8XX) && defined(CONFIG_ARCH_DAVINCI_DMx)
-#error Cannot enable DaVinci and DA8XX platforms concurrently
-#elif defined(CONFIG_ARCH_DAVINCI_DA8XX)
-#define PLAT_PHYS_OFFSET DA8XX_DDR_BASE
-#else
-#define PLAT_PHYS_OFFSET DAVINCI_DDR_BASE
-#endif
-
-#define DDR2_SDRCR_OFFSET	0xc
-#define DDR2_SRPD_BIT		BIT(23)
-#define DDR2_MCLKSTOPEN_BIT	BIT(30)
-#define DDR2_LPMODEN_BIT	BIT(31)
-
-/*
- * Increase size of DMA-consistent memory region
- */
-#define CONSISTENT_DMA_SIZE (14<<20)
-
-#endif /* __ASM_ARCH_MEMORY_H */
diff --git a/arch/arm/mach-davinci/include/mach/serial.h b/arch/arm/mach-davinci/include/mach/serial.h
index c9e6ce1..e347d88 100644
--- a/arch/arm/mach-davinci/include/mach/serial.h
+++ b/arch/arm/mach-davinci/include/mach/serial.h
@@ -21,8 +21,9 @@
  * macros in debug-macro.S.
  *
  * This area sits just below the page tables (see arch/arm/kernel/head.S).
+ * We define it as a relative offset from start of usable RAM.
  */
-#define DAVINCI_UART_INFO	(PLAT_PHYS_OFFSET + 0x3ff8)
+#define DAVINCI_UART_INFO_OFS	0x3ff8
 
 #define DAVINCI_UART0_BASE	(IO_PHYS + 0x20000)
 #define DAVINCI_UART1_BASE	(IO_PHYS + 0x20400)
diff --git a/arch/arm/mach-davinci/include/mach/uncompress.h b/arch/arm/mach-davinci/include/mach/uncompress.h
index 78d8068..9dc7cf9 100644
--- a/arch/arm/mach-davinci/include/mach/uncompress.h
+++ b/arch/arm/mach-davinci/include/mach/uncompress.h
@@ -43,7 +43,12 @@
 
 static inline void set_uart_info(u32 phys, void * __iomem virt)
 {
-	u32 *uart_info = (u32 *)(DAVINCI_UART_INFO);
+	/*
+	 * Get address of some.bss variable and round it down
+	 * a la CONFIG_AUTO_ZRELADDR.
+	 */
+	u32 ram_start = (u32)&uart & 0xf8000000;
+	u32 *uart_info = (u32 *)(ram_start + DAVINCI_UART_INFO_OFS);
 
 	uart = (u32 *)phys;
 	uart_info[0] = phys;
diff --git a/arch/arm/mach-davinci/sleep.S b/arch/arm/mach-davinci/sleep.S
index 5f1e045..d4e9316 100644
--- a/arch/arm/mach-davinci/sleep.S
+++ b/arch/arm/mach-davinci/sleep.S
@@ -22,7 +22,7 @@
 #include <linux/linkage.h>
 #include <asm/assembler.h>
 #include <mach/psc.h>
-#include <mach/memory.h>
+#include <mach/ddr2.h>
 
 #include "clock.h"
 
diff --git a/arch/arm/mach-dove/cm-a510.c b/arch/arm/mach-dove/cm-a510.c
index 03e11f9..c8a406f 100644
--- a/arch/arm/mach-dove/cm-a510.c
+++ b/arch/arm/mach-dove/cm-a510.c
@@ -87,7 +87,7 @@
 }
 
 MACHINE_START(CM_A510, "Compulab CM-A510 Board")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= cm_a510_init,
 	.map_io		= dove_map_io,
 	.init_early	= dove_init_early,
diff --git a/arch/arm/mach-dove/dove-db-setup.c b/arch/arm/mach-dove/dove-db-setup.c
index 2ac34ec..11ea34e 100644
--- a/arch/arm/mach-dove/dove-db-setup.c
+++ b/arch/arm/mach-dove/dove-db-setup.c
@@ -94,7 +94,7 @@
 }
 
 MACHINE_START(DOVE_DB, "Marvell DB-MV88AP510-BP Development Board")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= dove_db_init,
 	.map_io		= dove_map_io,
 	.init_early	= dove_init_early,
diff --git a/arch/arm/mach-dove/include/mach/debug-macro.S b/arch/arm/mach-dove/include/mach/debug-macro.S
index da8bf2b..5929cbc 100644
--- a/arch/arm/mach-dove/include/mach/debug-macro.S
+++ b/arch/arm/mach-dove/include/mach/debug-macro.S
@@ -8,7 +8,7 @@
 
 #include <mach/bridge-regs.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =DOVE_SB_REGS_PHYS_BASE
 	ldr	\rv, =DOVE_SB_REGS_VIRT_BASE
 	orr	\rp, \rp, #0x00012000
diff --git a/arch/arm/mach-dove/include/mach/memory.h b/arch/arm/mach-dove/include/mach/memory.h
deleted file mode 100644
index bbc93fe..0000000
--- a/arch/arm/mach-dove/include/mach/memory.h
+++ /dev/null
@@ -1,10 +0,0 @@
-/*
- * arch/arm/mach-dove/include/mach/memory.h
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET		UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-ebsa110/core.c b/arch/arm/mach-ebsa110/core.c
index 087bc77..d0ce8ab 100644
--- a/arch/arm/mach-ebsa110/core.c
+++ b/arch/arm/mach-ebsa110/core.c
@@ -280,7 +280,7 @@
 
 MACHINE_START(EBSA110, "EBSA110")
 	/* Maintainer: Russell King */
-	.boot_params	= 0x00000400,
+	.atag_offset	= 0x400,
 	.reserve_lp0	= 1,
 	.reserve_lp2	= 1,
 	.soft_reboot	= 1,
diff --git a/arch/arm/mach-ebsa110/include/mach/debug-macro.S b/arch/arm/mach-ebsa110/include/mach/debug-macro.S
index 7ef5690..bb02c05 100644
--- a/arch/arm/mach-ebsa110/include/mach/debug-macro.S
+++ b/arch/arm/mach-ebsa110/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  *
 **/
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0xf0000000
 		orr	\rp, \rp, #0x00000be0
 		mov	\rp, \rv
diff --git a/arch/arm/mach-ep93xx/adssphere.c b/arch/arm/mach-ep93xx/adssphere.c
index 61b98ce..0713448 100644
--- a/arch/arm/mach-ep93xx/adssphere.c
+++ b/arch/arm/mach-ep93xx/adssphere.c
@@ -33,7 +33,7 @@
 
 MACHINE_START(ADSSPHERE, "ADS Sphere board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c
index 9969bb1..257175e 100644
--- a/arch/arm/mach-ep93xx/edb93xx.c
+++ b/arch/arm/mach-ep93xx/edb93xx.c
@@ -240,7 +240,7 @@
 #ifdef CONFIG_MACH_EDB9301
 MACHINE_START(EDB9301, "Cirrus Logic EDB9301 Evaluation Board")
 	/* Maintainer: H Hartley Sweeten <hsweeten@visionengravers.com> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -251,7 +251,7 @@
 #ifdef CONFIG_MACH_EDB9302
 MACHINE_START(EDB9302, "Cirrus Logic EDB9302 Evaluation Board")
 	/* Maintainer: George Kashperko <george@chas.com.ua> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -262,7 +262,7 @@
 #ifdef CONFIG_MACH_EDB9302A
 MACHINE_START(EDB9302A, "Cirrus Logic EDB9302A Evaluation Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -273,7 +273,7 @@
 #ifdef CONFIG_MACH_EDB9307
 MACHINE_START(EDB9307, "Cirrus Logic EDB9307 Evaluation Board")
 	/* Maintainer: Herbert Valerio Riedel <hvr@gnu.org> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -284,7 +284,7 @@
 #ifdef CONFIG_MACH_EDB9307A
 MACHINE_START(EDB9307A, "Cirrus Logic EDB9307A Evaluation Board")
 	/* Maintainer: H Hartley Sweeten <hsweeten@visionengravers.com> */
-	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -295,7 +295,7 @@
 #ifdef CONFIG_MACH_EDB9312
 MACHINE_START(EDB9312, "Cirrus Logic EDB9312 Evaluation Board")
 	/* Maintainer: Toufeeq Hussain <toufeeq_hussain@infosys.com> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -306,7 +306,7 @@
 #ifdef CONFIG_MACH_EDB9315
 MACHINE_START(EDB9315, "Cirrus Logic EDB9315 Evaluation Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -317,7 +317,7 @@
 #ifdef CONFIG_MACH_EDB9315A
 MACHINE_START(EDB9315A, "Cirrus Logic EDB9315A Evaluation Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
diff --git a/arch/arm/mach-ep93xx/gesbc9312.c b/arch/arm/mach-ep93xx/gesbc9312.c
index 9bd3152..45ee205 100644
--- a/arch/arm/mach-ep93xx/gesbc9312.c
+++ b/arch/arm/mach-ep93xx/gesbc9312.c
@@ -33,7 +33,7 @@
 
 MACHINE_START(GESBC9312, "Glomation GESBC-9312-sx")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
diff --git a/arch/arm/mach-ep93xx/include/mach/debug-macro.S b/arch/arm/mach-ep93xx/include/mach/debug-macro.S
index b25bc907..af54e43 100644
--- a/arch/arm/mach-ep93xx/include/mach/debug-macro.S
+++ b/arch/arm/mach-ep93xx/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  */
 #include <mach/ep93xx-regs.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =EP93XX_APB_PHYS_BASE	@ Physical base
 		ldr	\rv, =EP93XX_APB_VIRT_BASE	@ virtual base
 		orr	\rp, \rp, #0x000c0000
diff --git a/arch/arm/mach-ep93xx/micro9.c b/arch/arm/mach-ep93xx/micro9.c
index 7adea62..e72f736 100644
--- a/arch/arm/mach-ep93xx/micro9.c
+++ b/arch/arm/mach-ep93xx/micro9.c
@@ -77,7 +77,7 @@
 #ifdef CONFIG_MACH_MICRO9H
 MACHINE_START(MICRO9, "Contec Micro9-High")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -88,7 +88,7 @@
 #ifdef CONFIG_MACH_MICRO9M
 MACHINE_START(MICRO9M, "Contec Micro9-Mid")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_ASYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -99,7 +99,7 @@
 #ifdef CONFIG_MACH_MICRO9L
 MACHINE_START(MICRO9L, "Contec Micro9-Lite")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -110,7 +110,7 @@
 #ifdef CONFIG_MACH_MICRO9S
 MACHINE_START(MICRO9S, "Contec Micro9-Slim")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_ASYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
diff --git a/arch/arm/mach-ep93xx/simone.c b/arch/arm/mach-ep93xx/simone.c
index 8392e95..238bc60 100644
--- a/arch/arm/mach-ep93xx/simone.c
+++ b/arch/arm/mach-ep93xx/simone.c
@@ -65,8 +65,8 @@
 }
 
 MACHINE_START(SIM_ONE, "Simplemachines Sim.One Board")
-/* Maintainer: Ryan Mallon */
-	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	/* Maintainer: Ryan Mallon */
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
diff --git a/arch/arm/mach-ep93xx/snappercl15.c b/arch/arm/mach-ep93xx/snappercl15.c
index 2e9c614..3bdf3a2 100644
--- a/arch/arm/mach-ep93xx/snappercl15.c
+++ b/arch/arm/mach-ep93xx/snappercl15.c
@@ -163,7 +163,7 @@
 
 MACHINE_START(SNAPPER_CL15, "Bluewater Systems Snapper CL15")
 	/* Maintainer: Ryan Mallon */
-	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer 		= &ep93xx_timer,
diff --git a/arch/arm/mach-ep93xx/ts72xx.c b/arch/arm/mach-ep93xx/ts72xx.c
index c2d2cf4..1ade3c3 100644
--- a/arch/arm/mach-ep93xx/ts72xx.c
+++ b/arch/arm/mach-ep93xx/ts72xx.c
@@ -257,7 +257,7 @@
 
 MACHINE_START(TS72XX, "Technologic Systems TS-72xx SBC")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ts72xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
diff --git a/arch/arm/mach-exynos4/include/mach/debug-macro.S b/arch/arm/mach-exynos4/include/mach/debug-macro.S
index a442ef8..6cacf16 100644
--- a/arch/arm/mach-exynos4/include/mach/debug-macro.S
+++ b/arch/arm/mach-exynos4/include/mach/debug-macro.S
@@ -20,7 +20,7 @@
 	 * aligned and add in the offset when we load the value here.
 	 */
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C_PA_UART
 		ldr	\rv, = S3C_VA_UART
 #if CONFIG_DEBUG_S3C_UART != 0
diff --git a/arch/arm/mach-exynos4/include/mach/entry-macro.S b/arch/arm/mach-exynos4/include/mach/entry-macro.S
index d7a1e28..006a4f4 100644
--- a/arch/arm/mach-exynos4/include/mach/entry-macro.S
+++ b/arch/arm/mach-exynos4/include/mach/entry-macro.S
@@ -55,7 +55,7 @@
 
 		bic     \irqnr, \irqstat, #0x1c00
 
-		cmp     \irqnr, #29
+		cmp     \irqnr, #15
 		cmpcc	\irqnr, \irqnr
 		cmpne	\irqnr, \tmp
 		cmpcs	\irqnr, \irqnr
@@ -76,8 +76,3 @@
 		strcc	\irqstat, [\base, #GIC_CPU_EOI]
 		cmpcs	\irqnr, \irqnr
 		.endm
-
-		/* As above, this assumes that irqstat and base are preserved.. */
-
-		.macro test_for_ltirq, irqnr, irqstat, base, tmp
-		.endm
diff --git a/arch/arm/mach-exynos4/mach-armlex4210.c b/arch/arm/mach-exynos4/mach-armlex4210.c
index b482c62..f0ca6c1 100644
--- a/arch/arm/mach-exynos4/mach-armlex4210.c
+++ b/arch/arm/mach-exynos4/mach-armlex4210.c
@@ -207,7 +207,7 @@
 
 MACHINE_START(ARMLEX4210, "ARMLEX4210")
 	/* Maintainer: Alim Akhtar <alim.akhtar@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= exynos4_init_irq,
 	.map_io		= armlex4210_map_io,
 	.init_machine	= armlex4210_machine_init,
diff --git a/arch/arm/mach-exynos4/mach-nuri.c b/arch/arm/mach-exynos4/mach-nuri.c
index 43be71b..6e05368 100644
--- a/arch/arm/mach-exynos4/mach-nuri.c
+++ b/arch/arm/mach-exynos4/mach-nuri.c
@@ -1152,7 +1152,7 @@
 
 MACHINE_START(NURI, "NURI")
 	/* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= exynos4_init_irq,
 	.map_io		= nuri_map_io,
 	.init_machine	= nuri_machine_init,
diff --git a/arch/arm/mach-exynos4/mach-smdkc210.c b/arch/arm/mach-exynos4/mach-smdkc210.c
index a7c65e0..b24ddd7 100644
--- a/arch/arm/mach-exynos4/mach-smdkc210.c
+++ b/arch/arm/mach-exynos4/mach-smdkc210.c
@@ -301,7 +301,7 @@
 
 MACHINE_START(SMDKC210, "SMDKC210")
 	/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= exynos4_init_irq,
 	.map_io		= smdkc210_map_io,
 	.init_machine	= smdkc210_machine_init,
diff --git a/arch/arm/mach-exynos4/mach-smdkv310.c b/arch/arm/mach-exynos4/mach-smdkv310.c
index ea41495..d90fcdd 100644
--- a/arch/arm/mach-exynos4/mach-smdkv310.c
+++ b/arch/arm/mach-exynos4/mach-smdkv310.c
@@ -255,7 +255,7 @@
 MACHINE_START(SMDKV310, "SMDKV310")
 	/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
 	/* Maintainer: Changhwan Youn <chaos.youn@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= exynos4_init_irq,
 	.map_io		= smdkv310_map_io,
 	.init_machine	= smdkv310_machine_init,
diff --git a/arch/arm/mach-exynos4/mach-universal_c210.c b/arch/arm/mach-exynos4/mach-universal_c210.c
index b3b5d89..2aac6f7 100644
--- a/arch/arm/mach-exynos4/mach-universal_c210.c
+++ b/arch/arm/mach-exynos4/mach-universal_c210.c
@@ -762,7 +762,7 @@
 
 MACHINE_START(UNIVERSAL_C210, "UNIVERSAL_C210")
 	/* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= exynos4_init_irq,
 	.map_io		= universal_map_io,
 	.init_machine	= universal_machine_init,
diff --git a/arch/arm/mach-exynos4/mct.c b/arch/arm/mach-exynos4/mct.c
index ddd8686..582b874 100644
--- a/arch/arm/mach-exynos4/mct.c
+++ b/arch/arm/mach-exynos4/mct.c
@@ -386,9 +386,11 @@
 
 	if (cpu == 0) {
 		mct_tick0_event_irq.dev_id = &mct_tick[cpu];
+		evt->irq = IRQ_MCT_L0;
 		setup_irq(IRQ_MCT_L0, &mct_tick0_event_irq);
 	} else {
 		mct_tick1_event_irq.dev_id = &mct_tick[cpu];
+		evt->irq = IRQ_MCT_L1;
 		setup_irq(IRQ_MCT_L1, &mct_tick1_event_irq);
 		irq_set_affinity(IRQ_MCT_L1, cpumask_of(1));
 	}
@@ -402,9 +404,10 @@
 	return 0;
 }
 
-int local_timer_ack(void)
+void local_timer_stop(struct clock_event_device *evt)
 {
-	return 0;
+	evt->set_mode(CLOCK_EVT_MODE_UNUSED, evt);
+	disable_irq(evt->irq);
 }
 
 #endif /* CONFIG_LOCAL_TIMERS */
diff --git a/arch/arm/mach-exynos4/platsmp.c b/arch/arm/mach-exynos4/platsmp.c
index df6ef1b..0c90896 100644
--- a/arch/arm/mach-exynos4/platsmp.c
+++ b/arch/arm/mach-exynos4/platsmp.c
@@ -193,12 +193,10 @@
 	ncores = scu_base ? scu_get_core_count(scu_base) : 1;
 
 	/* sanity check */
-	if (ncores > NR_CPUS) {
-		printk(KERN_WARNING
-		       "EXYNOS4: no. of cores (%d) greater than configured "
-		       "maximum of %d - clipping\n",
-		       ncores, NR_CPUS);
-		ncores = NR_CPUS;
+	if (ncores > nr_cpu_ids) {
+		pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+			ncores, nr_cpu_ids);
+		ncores = nr_cpu_ids;
 	}
 
 	for (i = 0; i < ncores; i++)
diff --git a/arch/arm/mach-footbridge/cats-hw.c b/arch/arm/mach-footbridge/cats-hw.c
index 5b1a8db..a3da5d1 100644
--- a/arch/arm/mach-footbridge/cats-hw.c
+++ b/arch/arm/mach-footbridge/cats-hw.c
@@ -86,7 +86,7 @@
 
 MACHINE_START(CATS, "Chalice-CATS")
 	/* Maintainer: Philip Blundell */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.soft_reboot	= 1,
 	.fixup		= fixup_cats,
 	.map_io		= footbridge_map_io,
diff --git a/arch/arm/mach-footbridge/ebsa285.c b/arch/arm/mach-footbridge/ebsa285.c
index 2ef69ff..012210c 100644
--- a/arch/arm/mach-footbridge/ebsa285.c
+++ b/arch/arm/mach-footbridge/ebsa285.c
@@ -15,7 +15,7 @@
 
 MACHINE_START(EBSA285, "EBSA285")
 	/* Maintainer: Russell King */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.video_start	= 0x000a0000,
 	.video_end	= 0x000bffff,
 	.map_io		= footbridge_map_io,
diff --git a/arch/arm/mach-footbridge/include/mach/debug-macro.S b/arch/arm/mach-footbridge/include/mach/debug-macro.S
index 1be2eeb..e5acde2 100644
--- a/arch/arm/mach-footbridge/include/mach/debug-macro.S
+++ b/arch/arm/mach-footbridge/include/mach/debug-macro.S
@@ -15,7 +15,7 @@
 
 #ifndef CONFIG_DEBUG_DC21285_PORT
 	/* For NetWinder debugging */
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x000003f8
 		orr	\rv, \rp, #0xff000000	@ virtual
 		orr	\rp, \rp, #0x7c000000	@ physical
@@ -31,7 +31,7 @@
 		.equ	dc21285_high, ARMCSR_BASE & 0xff000000
 		.equ	dc21285_low,  ARMCSR_BASE & 0x00ffffff
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		.if	dc21285_low
 		mov	\rp, #dc21285_low
 		.else
diff --git a/arch/arm/mach-footbridge/netwinder-hw.c b/arch/arm/mach-footbridge/netwinder-hw.c
index 06e514f..d8c1c92 100644
--- a/arch/arm/mach-footbridge/netwinder-hw.c
+++ b/arch/arm/mach-footbridge/netwinder-hw.c
@@ -648,7 +648,7 @@
 
 MACHINE_START(NETWINDER, "Rebel-NetWinder")
 	/* Maintainer: Russell King/Rebel.com */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.video_start	= 0x000a0000,
 	.video_end	= 0x000bffff,
 	.reserve_lp0	= 1,
diff --git a/arch/arm/mach-footbridge/personal.c b/arch/arm/mach-footbridge/personal.c
index 3285e91..f41dba3 100644
--- a/arch/arm/mach-footbridge/personal.c
+++ b/arch/arm/mach-footbridge/personal.c
@@ -15,7 +15,7 @@
 
 MACHINE_START(PERSONAL_SERVER, "Compaq-PersonalServer")
 	/* Maintainer: Jamey Hicks / George France */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= footbridge_map_io,
 	.init_irq	= footbridge_init_irq,
 	.timer		= &footbridge_timer,
diff --git a/arch/arm/mach-gemini/board-nas4220b.c b/arch/arm/mach-gemini/board-nas4220b.c
index 0cf7a07..5927d3c 100644
--- a/arch/arm/mach-gemini/board-nas4220b.c
+++ b/arch/arm/mach-gemini/board-nas4220b.c
@@ -102,7 +102,7 @@
 }
 
 MACHINE_START(NAS4220B, "Raidsonic NAS IB-4220-B")
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= gemini_map_io,
 	.init_irq	= gemini_init_irq,
 	.timer		= &ib4220b_timer,
diff --git a/arch/arm/mach-gemini/board-rut1xx.c b/arch/arm/mach-gemini/board-rut1xx.c
index 4fa09af..cd7437a 100644
--- a/arch/arm/mach-gemini/board-rut1xx.c
+++ b/arch/arm/mach-gemini/board-rut1xx.c
@@ -86,7 +86,7 @@
 }
 
 MACHINE_START(RUT100, "Teltonika RUT100")
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= gemini_map_io,
 	.init_irq	= gemini_init_irq,
 	.timer		= &rut1xx_timer,
diff --git a/arch/arm/mach-gemini/board-wbd111.c b/arch/arm/mach-gemini/board-wbd111.c
index 88cc422..a367880 100644
--- a/arch/arm/mach-gemini/board-wbd111.c
+++ b/arch/arm/mach-gemini/board-wbd111.c
@@ -129,7 +129,7 @@
 }
 
 MACHINE_START(WBD111, "Wiliboard WBD-111")
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= gemini_map_io,
 	.init_irq	= gemini_init_irq,
 	.timer		= &wbd111_timer,
diff --git a/arch/arm/mach-gemini/board-wbd222.c b/arch/arm/mach-gemini/board-wbd222.c
index 3a22034..f382811 100644
--- a/arch/arm/mach-gemini/board-wbd222.c
+++ b/arch/arm/mach-gemini/board-wbd222.c
@@ -129,7 +129,7 @@
 }
 
 MACHINE_START(WBD222, "Wiliboard WBD-222")
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= gemini_map_io,
 	.init_irq	= gemini_init_irq,
 	.timer		= &wbd222_timer,
diff --git a/arch/arm/mach-gemini/include/mach/debug-macro.S b/arch/arm/mach-gemini/include/mach/debug-macro.S
index f40e006..8376707 100644
--- a/arch/arm/mach-gemini/include/mach/debug-macro.S
+++ b/arch/arm/mach-gemini/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  */
 #include <mach/hardware.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =GEMINI_UART_BASE			@ physical
 	ldr	\rv, =IO_ADDRESS(GEMINI_UART_BASE)	@ virtual
 	.endm
diff --git a/arch/arm/mach-gemini/include/mach/memory.h b/arch/arm/mach-gemini/include/mach/memory.h
deleted file mode 100644
index a50915f..0000000
--- a/arch/arm/mach-gemini/include/mach/memory.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- *  Copyright (C) 2001-2006 Storlink, Corp.
- *  Copyright (C) 2008-2009 Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-#ifndef __MACH_MEMORY_H
-#define __MACH_MEMORY_H
-
-#ifdef CONFIG_GEMINI_MEM_SWAP
-# define PLAT_PHYS_OFFSET	UL(0x00000000)
-#else
-# define PLAT_PHYS_OFFSET	UL(0x10000000)
-#endif
-
-#endif /* __MACH_MEMORY_H */
diff --git a/arch/arm/mach-h720x/h7201-eval.c b/arch/arm/mach-h720x/h7201-eval.c
index 65f1bea..9886f19 100644
--- a/arch/arm/mach-h720x/h7201-eval.c
+++ b/arch/arm/mach-h720x/h7201-eval.c
@@ -29,7 +29,7 @@
 
 MACHINE_START(H7201, "Hynix GMS30C7201")
 	/* Maintainer: Robert Schwebel, Pengutronix */
-	.boot_params	= 0xc0001000,
+	.atag_offset	= 0x1000,
 	.map_io		= h720x_map_io,
 	.init_irq	= h720x_init_irq,
 	.timer		= &h7201_timer,
diff --git a/arch/arm/mach-h720x/h7202-eval.c b/arch/arm/mach-h720x/h7202-eval.c
index 884584a..284a134 100644
--- a/arch/arm/mach-h720x/h7202-eval.c
+++ b/arch/arm/mach-h720x/h7202-eval.c
@@ -71,7 +71,7 @@
 
 MACHINE_START(H7202, "Hynix HMS30C7202")
 	/* Maintainer: Robert Schwebel, Pengutronix */
-	.boot_params	= 0x40000100,
+	.atag_offset	= 0x100,
 	.map_io		= h720x_map_io,
 	.init_irq	= h7202_init_irq,
 	.timer		= &h7202_timer,
diff --git a/arch/arm/mach-h720x/include/mach/debug-macro.S b/arch/arm/mach-h720x/include/mach/debug-macro.S
index c2093e8..8a46157 100644
--- a/arch/arm/mach-h720x/include/mach/debug-macro.S
+++ b/arch/arm/mach-h720x/include/mach/debug-macro.S
@@ -16,7 +16,7 @@
 		.equ    io_virt, IO_VIRT
 		.equ    io_phys, IO_PHYS
 
-		.macro  addruart, rp, rv
+		.macro  addruart, rp, rv, tmp
 		mov     \rp, #0x00020000	@ UART1
 		add     \rv, \rp, #io_virt	@ virtual address
 		add     \rp, \rp, #io_phys	@ physical base address
diff --git a/arch/arm/mach-h720x/include/mach/memory.h b/arch/arm/mach-h720x/include/mach/memory.h
deleted file mode 100644
index 96dcf50..0000000
--- a/arch/arm/mach-h720x/include/mach/memory.h
+++ /dev/null
@@ -1,11 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/memory.h
- *
- * Copyright (c) 2000 Jungjun Kim
- *
- */
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET	UL(0x40000000)
-#endif
diff --git a/arch/arm/mach-imx/mach-armadillo5x0.c b/arch/arm/mach-imx/mach-armadillo5x0.c
index e008554..c9a9cf6 100644
--- a/arch/arm/mach-imx/mach-armadillo5x0.c
+++ b/arch/arm/mach-imx/mach-armadillo5x0.c
@@ -554,7 +554,7 @@
 
 MACHINE_START(ARMADILLO5X0, "Armadillo-500")
 	/* Maintainer: Alberto Panizzo  */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx31_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31_init_irq,
diff --git a/arch/arm/mach-imx/mach-cpuimx27.c b/arch/arm/mach-imx/mach-cpuimx27.c
index a8364cc..edb3730 100644
--- a/arch/arm/mach-imx/mach-cpuimx27.c
+++ b/arch/arm/mach-imx/mach-cpuimx27.c
@@ -311,7 +311,7 @@
 };
 
 MACHINE_START(EUKREA_CPUIMX27, "EUKREA CPUIMX27")
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,
diff --git a/arch/arm/mach-imx/mach-cpuimx35.c b/arch/arm/mach-imx/mach-cpuimx35.c
index fc4fea1..66af2e8 100644
--- a/arch/arm/mach-imx/mach-cpuimx35.c
+++ b/arch/arm/mach-imx/mach-cpuimx35.c
@@ -194,7 +194,7 @@
 
 MACHINE_START(EUKREA_CPUIMX35SD, "Eukrea CPUIMX35")
 	/* Maintainer: Eukrea Electromatique */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx35_map_io,
 	.init_early = imx35_init_early,
 	.init_irq = mx35_init_irq,
diff --git a/arch/arm/mach-imx/mach-eukrea_cpuimx25.c b/arch/arm/mach-imx/mach-eukrea_cpuimx25.c
index b05de09..ab8fbcc 100644
--- a/arch/arm/mach-imx/mach-eukrea_cpuimx25.c
+++ b/arch/arm/mach-imx/mach-eukrea_cpuimx25.c
@@ -163,7 +163,7 @@
 
 MACHINE_START(EUKREA_CPUIMX25SD, "Eukrea CPUIMX25")
 	/* Maintainer: Eukrea Electromatique */
-	.boot_params = MX25_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx25_map_io,
 	.init_early = imx25_init_early,
 	.init_irq = mx25_init_irq,
diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
index 678cf83..38eb9e4 100644
--- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
+++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
@@ -275,7 +275,7 @@
 };
 
 MACHINE_START(IMX27_VISSTRIM_M10, "Vista Silicon Visstrim_M10")
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,
diff --git a/arch/arm/mach-imx/mach-imx27ipcam.c b/arch/arm/mach-imx/mach-imx27ipcam.c
index f572ce9..7052155 100644
--- a/arch/arm/mach-imx/mach-imx27ipcam.c
+++ b/arch/arm/mach-imx/mach-imx27ipcam.c
@@ -71,7 +71,7 @@
 
 MACHINE_START(IMX27IPCAM, "Freescale IMX27IPCAM")
 	/* maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,
diff --git a/arch/arm/mach-imx/mach-imx27lite.c b/arch/arm/mach-imx/mach-imx27lite.c
index e7fc4f0..8d6a635 100644
--- a/arch/arm/mach-imx/mach-imx27lite.c
+++ b/arch/arm/mach-imx/mach-imx27lite.c
@@ -77,7 +77,7 @@
 };
 
 MACHINE_START(IMX27LITE, "LogicPD i.MX27LITE")
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,
diff --git a/arch/arm/mach-imx/mach-kzm_arm11_01.c b/arch/arm/mach-imx/mach-kzm_arm11_01.c
index a65d910..4288e8f 100644
--- a/arch/arm/mach-imx/mach-kzm_arm11_01.c
+++ b/arch/arm/mach-imx/mach-kzm_arm11_01.c
@@ -271,7 +271,7 @@
 };
 
 MACHINE_START(KZM_ARM11_01, "Kyoto Microcomputer Co., Ltd. KZM-ARM11-01")
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = kzm_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx1ads.c b/arch/arm/mach-imx/mach-mx1ads.c
index ebe9a29..fc49785 100644
--- a/arch/arm/mach-imx/mach-mx1ads.c
+++ b/arch/arm/mach-imx/mach-mx1ads.c
@@ -140,7 +140,7 @@
 
 MACHINE_START(MX1ADS, "Freescale MX1ADS")
 	/* Maintainer: Sascha Hauer, Pengutronix */
-	.boot_params = MX1_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx1_map_io,
 	.init_early = imx1_init_early,
 	.init_irq = mx1_init_irq,
@@ -150,7 +150,7 @@
 MACHINE_END
 
 MACHINE_START(MXLADS, "Freescale MXLADS")
-	.boot_params = MX1_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx1_map_io,
 	.init_early = imx1_init_early,
 	.init_irq = mx1_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx21ads.c b/arch/arm/mach-imx/mach-mx21ads.c
index 43dd22b..25f8402 100644
--- a/arch/arm/mach-imx/mach-mx21ads.c
+++ b/arch/arm/mach-imx/mach-mx21ads.c
@@ -305,7 +305,7 @@
 
 MACHINE_START(MX21ADS, "Freescale i.MX21ADS")
 	/* maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX21_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx21ads_map_io,
 	.init_early = imx21_init_early,
 	.init_irq = mx21_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx25_3ds.c b/arch/arm/mach-imx/mach-mx25_3ds.c
index bd735ad..88dccf1 100644
--- a/arch/arm/mach-imx/mach-mx25_3ds.c
+++ b/arch/arm/mach-imx/mach-mx25_3ds.c
@@ -263,7 +263,7 @@
 
 MACHINE_START(MX25_3DS, "Freescale MX25PDK (3DS)")
 	/* Maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX25_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx25_map_io,
 	.init_early = imx25_init_early,
 	.init_irq = mx25_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx27_3ds.c b/arch/arm/mach-imx/mach-mx27_3ds.c
index b2bc10b..71bb45d 100644
--- a/arch/arm/mach-imx/mach-mx27_3ds.c
+++ b/arch/arm/mach-imx/mach-mx27_3ds.c
@@ -421,7 +421,7 @@
 
 MACHINE_START(MX27_3DS, "Freescale MX27PDK")
 	/* maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx27ads.c b/arch/arm/mach-imx/mach-mx27ads.c
index e6d1321..e75f391 100644
--- a/arch/arm/mach-imx/mach-mx27ads.c
+++ b/arch/arm/mach-imx/mach-mx27ads.c
@@ -345,7 +345,7 @@
 
 MACHINE_START(MX27ADS, "Freescale i.MX27ADS")
 	/* maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27ads_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx31_3ds.c b/arch/arm/mach-imx/mach-mx31_3ds.c
index b4aa9c3..eb3e3fe 100644
--- a/arch/arm/mach-imx/mach-mx31_3ds.c
+++ b/arch/arm/mach-imx/mach-mx31_3ds.c
@@ -764,7 +764,7 @@
 
 MACHINE_START(MX31_3DS, "Freescale MX31PDK (3DS)")
 	/* Maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx31_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx31ads.c b/arch/arm/mach-imx/mach-mx31ads.c
index 13e7347..9cc1a49 100644
--- a/arch/arm/mach-imx/mach-mx31ads.c
+++ b/arch/arm/mach-imx/mach-mx31ads.c
@@ -535,7 +535,7 @@
 
 MACHINE_START(MX31ADS, "Freescale MX31ADS")
 	/* Maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx31ads_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31ads_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx31lilly.c b/arch/arm/mach-imx/mach-mx31lilly.c
index 070a8d1..5defd8e 100644
--- a/arch/arm/mach-imx/mach-mx31lilly.c
+++ b/arch/arm/mach-imx/mach-mx31lilly.c
@@ -295,7 +295,7 @@
 };
 
 MACHINE_START(LILLY1131, "INCO startec LILLY-1131")
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx31_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx31lite.c b/arch/arm/mach-imx/mach-mx31lite.c
index 4f66ea4..c97c26d 100644
--- a/arch/arm/mach-imx/mach-mx31lite.c
+++ b/arch/arm/mach-imx/mach-mx31lite.c
@@ -280,7 +280,7 @@
 
 MACHINE_START(MX31LITE, "LogicPD i.MX31 SOM")
 	/* Maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx31lite_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx31moboard.c b/arch/arm/mach-imx/mach-mx31moboard.c
index cd07ebe..fff7791 100644
--- a/arch/arm/mach-imx/mach-mx31moboard.c
+++ b/arch/arm/mach-imx/mach-mx31moboard.c
@@ -584,7 +584,7 @@
 
 MACHINE_START(MX31MOBOARD, "EPFL Mobots mx31moboard")
 	/* Maintainer: Valentin Longchamp, EPFL Mobots group */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.reserve = mx31moboard_reserve,
 	.map_io = mx31_map_io,
 	.init_early = imx31_init_early,
diff --git a/arch/arm/mach-imx/mach-mx35_3ds.c b/arch/arm/mach-imx/mach-mx35_3ds.c
index 5a5eb3e..7a46202 100644
--- a/arch/arm/mach-imx/mach-mx35_3ds.c
+++ b/arch/arm/mach-imx/mach-mx35_3ds.c
@@ -217,7 +217,7 @@
 
 MACHINE_START(MX35_3DS, "Freescale MX35PDK")
 	/* Maintainer: Freescale Semiconductor, Inc */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx35_map_io,
 	.init_early = imx35_init_early,
 	.init_irq = mx35_init_irq,
diff --git a/arch/arm/mach-imx/mach-mxt_td60.c b/arch/arm/mach-imx/mach-mxt_td60.c
index d01a92f..125c196 100644
--- a/arch/arm/mach-imx/mach-mxt_td60.c
+++ b/arch/arm/mach-imx/mach-mxt_td60.c
@@ -267,7 +267,7 @@
 
 MACHINE_START(MXT_TD60, "Maxtrack i-MXT TD60")
 	/* maintainer: Maxtrack Industrial */
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,
diff --git a/arch/arm/mach-imx/mach-pca100.c b/arch/arm/mach-imx/mach-pca100.c
index 100babc..26072f4 100644
--- a/arch/arm/mach-imx/mach-pca100.c
+++ b/arch/arm/mach-imx/mach-pca100.c
@@ -435,7 +435,7 @@
 };
 
 MACHINE_START(PCA100, "phyCARD-i.MX27")
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,
diff --git a/arch/arm/mach-imx/mach-pcm037.c b/arch/arm/mach-imx/mach-pcm037.c
index 3fb5eaa..efd6b53 100644
--- a/arch/arm/mach-imx/mach-pcm037.c
+++ b/arch/arm/mach-imx/mach-pcm037.c
@@ -688,7 +688,7 @@
 
 MACHINE_START(PCM037, "Phytec Phycore pcm037")
 	/* Maintainer: Pengutronix */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.reserve = pcm037_reserve,
 	.map_io = mx31_map_io,
 	.init_early = imx31_init_early,
diff --git a/arch/arm/mach-imx/mach-pcm038.c b/arch/arm/mach-imx/mach-pcm038.c
index dac2b79..f0a5282 100644
--- a/arch/arm/mach-imx/mach-pcm038.c
+++ b/arch/arm/mach-imx/mach-pcm038.c
@@ -349,7 +349,7 @@
 };
 
 MACHINE_START(PCM038, "phyCORE-i.MX27")
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,
diff --git a/arch/arm/mach-imx/mach-pcm043.c b/arch/arm/mach-imx/mach-pcm043.c
index a27baa4..7366c2a 100644
--- a/arch/arm/mach-imx/mach-pcm043.c
+++ b/arch/arm/mach-imx/mach-pcm043.c
@@ -418,7 +418,7 @@
 
 MACHINE_START(PCM043, "Phytec Phycore pcm043")
 	/* Maintainer: Pengutronix */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx35_map_io,
 	.init_early = imx35_init_early,
 	.init_irq = mx35_init_irq,
diff --git a/arch/arm/mach-imx/mach-qong.c b/arch/arm/mach-imx/mach-qong.c
index 4243d1f..1c4822b 100644
--- a/arch/arm/mach-imx/mach-qong.c
+++ b/arch/arm/mach-imx/mach-qong.c
@@ -263,7 +263,7 @@
 
 MACHINE_START(QONG, "Dave/DENX QongEVB-LITE")
 	/* Maintainer: DENX Software Engineering GmbH */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx31_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31_init_irq,
diff --git a/arch/arm/mach-imx/mach-scb9328.c b/arch/arm/mach-imx/mach-scb9328.c
index 17f15fb..bb6e5b2 100644
--- a/arch/arm/mach-imx/mach-scb9328.c
+++ b/arch/arm/mach-imx/mach-scb9328.c
@@ -137,7 +137,7 @@
 
 MACHINE_START(SCB9328, "Synertronixx scb9328")
 	/* Sascha Hauer */
-	.boot_params = 0x08000100,
+	.atag_offset = 100,
 	.map_io = mx1_map_io,
 	.init_early = imx1_init_early,
 	.init_irq = mx1_init_irq,
diff --git a/arch/arm/mach-integrator/include/mach/debug-macro.S b/arch/arm/mach-integrator/include/mach/debug-macro.S
index a1f598f..411b116 100644
--- a/arch/arm/mach-integrator/include/mach/debug-macro.S
+++ b/arch/arm/mach-integrator/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x16000000	@ physical base address
 		mov	\rv, #0xf0000000	@ virtual base
 		add	\rv, \rv, #0x16000000 >> 4
diff --git a/arch/arm/mach-integrator/integrator_ap.c b/arch/arm/mach-integrator/integrator_ap.c
index 8cdc730..a20fb3f 100644
--- a/arch/arm/mach-integrator/integrator_ap.c
+++ b/arch/arm/mach-integrator/integrator_ap.c
@@ -459,7 +459,7 @@
 
 MACHINE_START(INTEGRATOR, "ARM-Integrator")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.reserve	= integrator_reserve,
 	.map_io		= ap_map_io,
 	.init_early	= integrator_init_early,
diff --git a/arch/arm/mach-integrator/integrator_cp.c b/arch/arm/mach-integrator/integrator_cp.c
index 4eb03ab..5de49c3 100644
--- a/arch/arm/mach-integrator/integrator_cp.c
+++ b/arch/arm/mach-integrator/integrator_cp.c
@@ -492,7 +492,7 @@
 
 MACHINE_START(CINTEGRATOR, "ARM-IntegratorCP")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.reserve	= integrator_reserve,
 	.map_io		= intcp_map_io,
 	.init_early	= intcp_init_early,
diff --git a/arch/arm/mach-iop13xx/include/mach/debug-macro.S b/arch/arm/mach-iop13xx/include/mach/debug-macro.S
index e664466..d869a6f 100644
--- a/arch/arm/mach-iop13xx/include/mach/debug-macro.S
+++ b/arch/arm/mach-iop13xx/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  * published by the Free Software Foundation.
  */
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	mov	\rp, #0x00002300
 	orr	\rp, \rp, #0x00000040
 	orr	\rv, \rp, #0xfe000000	@ virtual
diff --git a/arch/arm/mach-iop13xx/iq81340mc.c b/arch/arm/mach-iop13xx/iq81340mc.c
index 23dfaff..4cf2cc4 100644
--- a/arch/arm/mach-iop13xx/iq81340mc.c
+++ b/arch/arm/mach-iop13xx/iq81340mc.c
@@ -91,7 +91,7 @@
 
 MACHINE_START(IQ81340MC, "Intel IQ81340MC")
 	/* Maintainer: Dan Williams <dan.j.williams@intel.com> */
-	.boot_params    = 0x00000100,
+	.atag_offset    = 0x100,
 	.map_io         = iop13xx_map_io,
 	.init_irq       = iop13xx_init_irq,
 	.timer          = &iq81340mc_timer,
diff --git a/arch/arm/mach-iop13xx/iq81340sc.c b/arch/arm/mach-iop13xx/iq81340sc.c
index df3492a..cd9e274 100644
--- a/arch/arm/mach-iop13xx/iq81340sc.c
+++ b/arch/arm/mach-iop13xx/iq81340sc.c
@@ -93,7 +93,7 @@
 
 MACHINE_START(IQ81340SC, "Intel IQ81340SC")
 	/* Maintainer: Dan Williams <dan.j.williams@intel.com> */
-	.boot_params    = 0x00000100,
+	.atag_offset    = 0x100,
 	.map_io         = iop13xx_map_io,
 	.init_irq       = iop13xx_init_irq,
 	.timer          = &iq81340sc_timer,
diff --git a/arch/arm/mach-iop32x/em7210.c b/arch/arm/mach-iop32x/em7210.c
index 6cbffbf..4325055 100644
--- a/arch/arm/mach-iop32x/em7210.c
+++ b/arch/arm/mach-iop32x/em7210.c
@@ -203,7 +203,7 @@
 }
 
 MACHINE_START(EM7210, "Lanner EM7210")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= em7210_map_io,
 	.init_irq	= iop32x_init_irq,
 	.timer		= &em7210_timer,
diff --git a/arch/arm/mach-iop32x/glantank.c b/arch/arm/mach-iop32x/glantank.c
index ceef5d4..0edc880 100644
--- a/arch/arm/mach-iop32x/glantank.c
+++ b/arch/arm/mach-iop32x/glantank.c
@@ -207,7 +207,7 @@
 
 MACHINE_START(GLANTANK, "GLAN Tank")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= glantank_map_io,
 	.init_irq	= iop32x_init_irq,
 	.timer		= &glantank_timer,
diff --git a/arch/arm/mach-iop32x/include/mach/debug-macro.S b/arch/arm/mach-iop32x/include/mach/debug-macro.S
index ff9e76c..363bdf9 100644
--- a/arch/arm/mach-iop32x/include/mach/debug-macro.S
+++ b/arch/arm/mach-iop32x/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  * published by the Free Software Foundation.
  */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0xfe000000	@ physical as well as virtual
 		orr	\rp, \rp, #0x00800000	@ location of the UART
 		mov	\rv, \rp
diff --git a/arch/arm/mach-iop32x/include/mach/memory.h b/arch/arm/mach-iop32x/include/mach/memory.h
deleted file mode 100644
index 169cc23..0000000
--- a/arch/arm/mach-iop32x/include/mach/memory.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-iop32x/include/mach/memory.h
- */
-
-#ifndef __MEMORY_H
-#define __MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET	UL(0xa0000000)
-
-#endif
diff --git a/arch/arm/mach-iop32x/iq31244.c b/arch/arm/mach-iop32x/iq31244.c
index 3a62514..9e7aacc 100644
--- a/arch/arm/mach-iop32x/iq31244.c
+++ b/arch/arm/mach-iop32x/iq31244.c
@@ -313,7 +313,7 @@
 
 MACHINE_START(IQ31244, "Intel IQ31244")
 	/* Maintainer: Intel Corp. */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= iq31244_map_io,
 	.init_irq	= iop32x_init_irq,
 	.timer		= &iq31244_timer,
@@ -327,7 +327,7 @@
  */
 MACHINE_START(EP80219, "Intel EP80219")
 	/* Maintainer: Intel Corp. */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= iq31244_map_io,
 	.init_irq	= iop32x_init_irq,
 	.timer		= &iq31244_timer,
diff --git a/arch/arm/mach-iop32x/iq80321.c b/arch/arm/mach-iop32x/iq80321.c
index 35b7e69..53ea86f 100644
--- a/arch/arm/mach-iop32x/iq80321.c
+++ b/arch/arm/mach-iop32x/iq80321.c
@@ -186,7 +186,7 @@
 
 MACHINE_START(IQ80321, "Intel IQ80321")
 	/* Maintainer: Intel Corp. */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= iq80321_map_io,
 	.init_irq	= iop32x_init_irq,
 	.timer		= &iq80321_timer,
diff --git a/arch/arm/mach-iop32x/n2100.c b/arch/arm/mach-iop32x/n2100.c
index 1a374ea..d726927 100644
--- a/arch/arm/mach-iop32x/n2100.c
+++ b/arch/arm/mach-iop32x/n2100.c
@@ -327,7 +327,7 @@
 
 MACHINE_START(N2100, "Thecus N2100")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= n2100_map_io,
 	.init_irq	= iop32x_init_irq,
 	.timer		= &n2100_timer,
diff --git a/arch/arm/mach-iop33x/include/mach/debug-macro.S b/arch/arm/mach-iop33x/include/mach/debug-macro.S
index 40c500d..361be1f 100644
--- a/arch/arm/mach-iop33x/include/mach/debug-macro.S
+++ b/arch/arm/mach-iop33x/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  * published by the Free Software Foundation.
  */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00ff0000
 		orr	\rp, \rp, #0x0000f700
 		orr	\rv, #0xfe000000	@ virtual
diff --git a/arch/arm/mach-iop33x/include/mach/memory.h b/arch/arm/mach-iop33x/include/mach/memory.h
deleted file mode 100644
index 8e1daf7..0000000
--- a/arch/arm/mach-iop33x/include/mach/memory.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-iop33x/include/mach/memory.h
- */
-
-#ifndef __MEMORY_H
-#define __MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET	UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-iop33x/iq80331.c b/arch/arm/mach-iop33x/iq80331.c
index 637c027..9e14ccc 100644
--- a/arch/arm/mach-iop33x/iq80331.c
+++ b/arch/arm/mach-iop33x/iq80331.c
@@ -141,7 +141,7 @@
 
 MACHINE_START(IQ80331, "Intel IQ80331")
 	/* Maintainer: Intel Corp. */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= iop3xx_map_io,
 	.init_irq	= iop33x_init_irq,
 	.timer		= &iq80331_timer,
diff --git a/arch/arm/mach-iop33x/iq80332.c b/arch/arm/mach-iop33x/iq80332.c
index 90a0436..09c899a 100644
--- a/arch/arm/mach-iop33x/iq80332.c
+++ b/arch/arm/mach-iop33x/iq80332.c
@@ -141,7 +141,7 @@
 
 MACHINE_START(IQ80332, "Intel IQ80332")
 	/* Maintainer: Intel Corp. */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= iop3xx_map_io,
 	.init_irq	= iop33x_init_irq,
 	.timer		= &iq80332_timer,
diff --git a/arch/arm/mach-ixp2000/enp2611.c b/arch/arm/mach-ixp2000/enp2611.c
index 62c60ad..af99945 100644
--- a/arch/arm/mach-ixp2000/enp2611.c
+++ b/arch/arm/mach-ixp2000/enp2611.c
@@ -254,7 +254,7 @@
 
 MACHINE_START(ENP2611, "Radisys ENP-2611 PCI network processor board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= enp2611_map_io,
 	.init_irq	= ixp2000_init_irq,
 	.timer		= &enp2611_timer,
diff --git a/arch/arm/mach-ixp2000/include/mach/debug-macro.S b/arch/arm/mach-ixp2000/include/mach/debug-macro.S
index 0ef533b..bdd3ccd 100644
--- a/arch/arm/mach-ixp2000/include/mach/debug-macro.S
+++ b/arch/arm/mach-ixp2000/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  *
 */
 
-		.macro  addruart, rp, rv
+		.macro  addruart, rp, rv, tmp
 		mov	\rp, #0x00030000
 #ifdef	__ARMEB__
 		orr	\rp, \rp, #0x00000003
diff --git a/arch/arm/mach-ixp2000/ixdp2400.c b/arch/arm/mach-ixp2000/ixdp2400.c
index 5bad1a8..f7dfd97 100644
--- a/arch/arm/mach-ixp2000/ixdp2400.c
+++ b/arch/arm/mach-ixp2000/ixdp2400.c
@@ -171,7 +171,7 @@
 
 MACHINE_START(IXDP2400, "Intel IXDP2400 Development Platform")
 	/* Maintainer: MontaVista Software, Inc. */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= ixdp2x00_map_io,
 	.init_irq	= ixdp2400_init_irq,
 	.timer		= &ixdp2400_timer,
diff --git a/arch/arm/mach-ixp2000/ixdp2800.c b/arch/arm/mach-ixp2000/ixdp2800.c
index 3d3cef8..d33bcac 100644
--- a/arch/arm/mach-ixp2000/ixdp2800.c
+++ b/arch/arm/mach-ixp2000/ixdp2800.c
@@ -286,7 +286,7 @@
 
 MACHINE_START(IXDP2800, "Intel IXDP2800 Development Platform")
 	/* Maintainer: MontaVista Software, Inc. */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= ixdp2x00_map_io,
 	.init_irq	= ixdp2800_init_irq,
 	.timer		= &ixdp2800_timer,
diff --git a/arch/arm/mach-ixp2000/ixdp2x01.c b/arch/arm/mach-ixp2000/ixdp2x01.c
index be2a254..61a2867 100644
--- a/arch/arm/mach-ixp2000/ixdp2x01.c
+++ b/arch/arm/mach-ixp2000/ixdp2x01.c
@@ -417,7 +417,7 @@
 #ifdef CONFIG_ARCH_IXDP2401
 MACHINE_START(IXDP2401, "Intel IXDP2401 Development Platform")
 	/* Maintainer: MontaVista Software, Inc. */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= ixdp2x01_map_io,
 	.init_irq	= ixdp2x01_init_irq,
 	.timer		= &ixdp2x01_timer,
@@ -428,7 +428,7 @@
 #ifdef CONFIG_ARCH_IXDP2801
 MACHINE_START(IXDP2801, "Intel IXDP2801 Development Platform")
 	/* Maintainer: MontaVista Software, Inc. */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= ixdp2x01_map_io,
 	.init_irq	= ixdp2x01_init_irq,
 	.timer		= &ixdp2x01_timer,
@@ -441,7 +441,7 @@
  */
 MACHINE_START(IXDP28X5, "Intel IXDP2805/2855 Development Platform")
 	/* Maintainer: MontaVista Software, Inc. */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= ixdp2x01_map_io,
 	.init_irq	= ixdp2x01_init_irq,
 	.timer		= &ixdp2x01_timer,
diff --git a/arch/arm/mach-ixp23xx/espresso.c b/arch/arm/mach-ixp23xx/espresso.c
index e25e5fe..30dd316 100644
--- a/arch/arm/mach-ixp23xx/espresso.c
+++ b/arch/arm/mach-ixp23xx/espresso.c
@@ -88,6 +88,6 @@
 	.map_io		= ixp23xx_map_io,
 	.init_irq	= ixp23xx_init_irq,
 	.timer		= &ixp23xx_timer,
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= espresso_init,
 MACHINE_END
diff --git a/arch/arm/mach-ixp23xx/include/mach/debug-macro.S b/arch/arm/mach-ixp23xx/include/mach/debug-macro.S
index f7c6eef..5ff524c 100644
--- a/arch/arm/mach-ixp23xx/include/mach/debug-macro.S
+++ b/arch/arm/mach-ixp23xx/include/mach/debug-macro.S
@@ -12,7 +12,7 @@
  */
 #include <mach/ixp23xx.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =IXP23XX_PERIPHERAL_PHYS 	@ physical
 		ldr	\rv, =IXP23XX_PERIPHERAL_VIRT	@ virtual
 #ifdef __ARMEB__
diff --git a/arch/arm/mach-ixp23xx/ixdp2351.c b/arch/arm/mach-ixp23xx/ixdp2351.c
index ec028e3..b3a57e0 100644
--- a/arch/arm/mach-ixp23xx/ixdp2351.c
+++ b/arch/arm/mach-ixp23xx/ixdp2351.c
@@ -331,6 +331,6 @@
 	.map_io		= ixdp2351_map_io,
 	.init_irq	= ixdp2351_init_irq,
 	.timer		= &ixp23xx_timer,
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= ixdp2351_init,
 MACHINE_END
diff --git a/arch/arm/mach-ixp23xx/roadrunner.c b/arch/arm/mach-ixp23xx/roadrunner.c
index 844551d..8f4dcbb 100644
--- a/arch/arm/mach-ixp23xx/roadrunner.c
+++ b/arch/arm/mach-ixp23xx/roadrunner.c
@@ -175,6 +175,6 @@
 	.map_io		= ixp23xx_map_io,
 	.init_irq	= ixp23xx_init_irq,
 	.timer		= &ixp23xx_timer,
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= roadrunner_init,
 MACHINE_END
diff --git a/arch/arm/mach-ixp4xx/avila-setup.c b/arch/arm/mach-ixp4xx/avila-setup.c
index ee19c1d..37609a2 100644
--- a/arch/arm/mach-ixp4xx/avila-setup.c
+++ b/arch/arm/mach-ixp4xx/avila-setup.c
@@ -167,7 +167,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= avila_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
@@ -185,7 +185,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= avila_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
diff --git a/arch/arm/mach-ixp4xx/coyote-setup.c b/arch/arm/mach-ixp4xx/coyote-setup.c
index e24564b..81dfec3 100644
--- a/arch/arm/mach-ixp4xx/coyote-setup.c
+++ b/arch/arm/mach-ixp4xx/coyote-setup.c
@@ -112,7 +112,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= coyote_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
@@ -130,7 +130,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= coyote_init,
 MACHINE_END
 #endif
diff --git a/arch/arm/mach-ixp4xx/dsmg600-setup.c b/arch/arm/mach-ixp4xx/dsmg600-setup.c
index 03e5451..71607a7 100644
--- a/arch/arm/mach-ixp4xx/dsmg600-setup.c
+++ b/arch/arm/mach-ixp4xx/dsmg600-setup.c
@@ -279,7 +279,7 @@
 
 MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")
 	/* Maintainer: www.nslu2-linux.org */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer          = &dsmg600_timer,
diff --git a/arch/arm/mach-ixp4xx/fsg-setup.c b/arch/arm/mach-ixp4xx/fsg-setup.c
index 23a8b36..a9540cd 100644
--- a/arch/arm/mach-ixp4xx/fsg-setup.c
+++ b/arch/arm/mach-ixp4xx/fsg-setup.c
@@ -273,7 +273,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= fsg_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
diff --git a/arch/arm/mach-ixp4xx/gateway7001-setup.c b/arch/arm/mach-ixp4xx/gateway7001-setup.c
index d4f851b..d69d1b0 100644
--- a/arch/arm/mach-ixp4xx/gateway7001-setup.c
+++ b/arch/arm/mach-ixp4xx/gateway7001-setup.c
@@ -99,7 +99,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= gateway7001_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
diff --git a/arch/arm/mach-ixp4xx/goramo_mlr.c b/arch/arm/mach-ixp4xx/goramo_mlr.c
index 7548d9a..bf6678d 100644
--- a/arch/arm/mach-ixp4xx/goramo_mlr.c
+++ b/arch/arm/mach-ixp4xx/goramo_mlr.c
@@ -499,7 +499,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= gmlr_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
diff --git a/arch/arm/mach-ixp4xx/gtwx5715-setup.c b/arch/arm/mach-ixp4xx/gtwx5715-setup.c
index 3790dff..aa029fc 100644
--- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c
+++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c
@@ -167,7 +167,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= gtwx5715_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
diff --git a/arch/arm/mach-ixp4xx/include/mach/debug-macro.S b/arch/arm/mach-ixp4xx/include/mach/debug-macro.S
index b974a49..8c9f8d5 100644
--- a/arch/arm/mach-ixp4xx/include/mach/debug-macro.S
+++ b/arch/arm/mach-ixp4xx/include/mach/debug-macro.S
@@ -10,7 +10,7 @@
  * published by the Free Software Foundation.
 */
 
-                .macro  addruart, rp, rv
+                .macro  addruart, rp, rv, tmp
 #ifdef __ARMEB__
                 mov     \rp, #3         @ Uart regs are at off set of 3 if
 					@ byte writes used - Big Endian.
diff --git a/arch/arm/mach-ixp4xx/include/mach/memory.h b/arch/arm/mach-ixp4xx/include/mach/memory.h
deleted file mode 100644
index 4caf176..0000000
--- a/arch/arm/mach-ixp4xx/include/mach/memory.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- * arch/arm/mach-ixp4xx/include/mach/memory.h
- *
- * Copyright (c) 2001-2004 MontaVista Software, Inc.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#include <asm/sizes.h>
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET	UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-ixp4xx/ixdp425-setup.c b/arch/arm/mach-ixp4xx/ixdp425-setup.c
index 6a29279..f235f82 100644
--- a/arch/arm/mach-ixp4xx/ixdp425-setup.c
+++ b/arch/arm/mach-ixp4xx/ixdp425-setup.c
@@ -256,7 +256,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= ixdp425_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
@@ -270,7 +270,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= ixdp425_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
@@ -284,7 +284,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= ixdp425_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
@@ -298,7 +298,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= ixdp425_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
diff --git a/arch/arm/mach-ixp4xx/nas100d-setup.c b/arch/arm/mach-ixp4xx/nas100d-setup.c
index afb5187..9f46692 100644
--- a/arch/arm/mach-ixp4xx/nas100d-setup.c
+++ b/arch/arm/mach-ixp4xx/nas100d-setup.c
@@ -314,7 +314,7 @@
 
 MACHINE_START(NAS100D, "Iomega NAS 100d")
 	/* Maintainer: www.nslu2-linux.org */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer          = &ixp4xx_timer,
diff --git a/arch/arm/mach-ixp4xx/nslu2-setup.c b/arch/arm/mach-ixp4xx/nslu2-setup.c
index 69e40f2..3676fbf 100644
--- a/arch/arm/mach-ixp4xx/nslu2-setup.c
+++ b/arch/arm/mach-ixp4xx/nslu2-setup.c
@@ -300,7 +300,7 @@
 
 MACHINE_START(NSLU2, "Linksys NSLU2")
 	/* Maintainer: www.nslu2-linux.org */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer          = &nslu2_timer,
diff --git a/arch/arm/mach-ixp4xx/vulcan-setup.c b/arch/arm/mach-ixp4xx/vulcan-setup.c
index 045336c..27e469e 100644
--- a/arch/arm/mach-ixp4xx/vulcan-setup.c
+++ b/arch/arm/mach-ixp4xx/vulcan-setup.c
@@ -239,7 +239,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= vulcan_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
diff --git a/arch/arm/mach-ixp4xx/wg302v2-setup.c b/arch/arm/mach-ixp4xx/wg302v2-setup.c
index 40b9fad..b14144b 100644
--- a/arch/arm/mach-ixp4xx/wg302v2-setup.c
+++ b/arch/arm/mach-ixp4xx/wg302v2-setup.c
@@ -100,7 +100,7 @@
 	.map_io		= ixp4xx_map_io,
 	.init_irq	= ixp4xx_init_irq,
 	.timer		= &ixp4xx_timer,
-	.boot_params	= 0x0100,
+	.atag_offset	= 0x100,
 	.init_machine	= wg302v2_init,
 #if defined(CONFIG_PCI)
 	.dma_zone_size	= SZ_64M,
diff --git a/arch/arm/mach-kirkwood/d2net_v2-setup.c b/arch/arm/mach-kirkwood/d2net_v2-setup.c
index 043cfd5..f457e07 100644
--- a/arch/arm/mach-kirkwood/d2net_v2-setup.c
+++ b/arch/arm/mach-kirkwood/d2net_v2-setup.c
@@ -221,7 +221,7 @@
 }
 
 MACHINE_START(D2NET_V2, "LaCie d2 Network v2")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= d2net_v2_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/db88f6281-bp-setup.c b/arch/arm/mach-kirkwood/db88f6281-bp-setup.c
index bff04e0..ff4c21c 100644
--- a/arch/arm/mach-kirkwood/db88f6281-bp-setup.c
+++ b/arch/arm/mach-kirkwood/db88f6281-bp-setup.c
@@ -97,7 +97,7 @@
 
 MACHINE_START(DB88F6281_BP, "Marvell DB-88F6281-BP Development Board")
 	/* Maintainer: Saeed Bishara <saeed@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= db88f6281_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/dockstar-setup.c b/arch/arm/mach-kirkwood/dockstar-setup.c
index f14dfb8..e4d199b 100644
--- a/arch/arm/mach-kirkwood/dockstar-setup.c
+++ b/arch/arm/mach-kirkwood/dockstar-setup.c
@@ -102,7 +102,7 @@
 }
 
 MACHINE_START(DOCKSTAR, "Seagate FreeAgent DockStar")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= dockstar_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/guruplug-setup.c b/arch/arm/mach-kirkwood/guruplug-setup.c
index 41d1b40..6c40f78 100644
--- a/arch/arm/mach-kirkwood/guruplug-setup.c
+++ b/arch/arm/mach-kirkwood/guruplug-setup.c
@@ -121,7 +121,7 @@
 
 MACHINE_START(GURUPLUG, "Marvell GuruPlug Reference Board")
 	/* Maintainer: Siddarth Gore <gores@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= guruplug_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/include/mach/debug-macro.S b/arch/arm/mach-kirkwood/include/mach/debug-macro.S
index db06ae43..f785d40 100644
--- a/arch/arm/mach-kirkwood/include/mach/debug-macro.S
+++ b/arch/arm/mach-kirkwood/include/mach/debug-macro.S
@@ -8,7 +8,7 @@
 
 #include <mach/bridge-regs.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =KIRKWOOD_REGS_PHYS_BASE
 	ldr	\rv, =KIRKWOOD_REGS_VIRT_BASE
 	orr	\rp, \rp, #0x00012000
diff --git a/arch/arm/mach-kirkwood/include/mach/memory.h b/arch/arm/mach-kirkwood/include/mach/memory.h
deleted file mode 100644
index 4600b44..0000000
--- a/arch/arm/mach-kirkwood/include/mach/memory.h
+++ /dev/null
@@ -1,10 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/include/mach/memory.h
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET		UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c b/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c
index 00cca22..9a1e917 100644
--- a/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c
+++ b/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c
@@ -163,7 +163,7 @@
 
 MACHINE_START(MV88F6281GTW_GE, "Marvell 88F6281 GTW GE Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= mv88f6281gtw_ge_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/netspace_v2-setup.c b/arch/arm/mach-kirkwood/netspace_v2-setup.c
index 7cdab57..8849bcc 100644
--- a/arch/arm/mach-kirkwood/netspace_v2-setup.c
+++ b/arch/arm/mach-kirkwood/netspace_v2-setup.c
@@ -258,7 +258,7 @@
 
 #ifdef CONFIG_MACH_NETSPACE_V2
 MACHINE_START(NETSPACE_V2, "LaCie Network Space v2")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= netspace_v2_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
@@ -269,7 +269,7 @@
 
 #ifdef CONFIG_MACH_INETSPACE_V2
 MACHINE_START(INETSPACE_V2, "LaCie Internet Space v2")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= netspace_v2_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
@@ -280,7 +280,7 @@
 
 #ifdef CONFIG_MACH_NETSPACE_MAX_V2
 MACHINE_START(NETSPACE_MAX_V2, "LaCie Network Space Max v2")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= netspace_v2_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/netxbig_v2-setup.c b/arch/arm/mach-kirkwood/netxbig_v2-setup.c
index 6be627d..1ba12c4 100644
--- a/arch/arm/mach-kirkwood/netxbig_v2-setup.c
+++ b/arch/arm/mach-kirkwood/netxbig_v2-setup.c
@@ -399,7 +399,7 @@
 
 #ifdef CONFIG_MACH_NET2BIG_V2
 MACHINE_START(NET2BIG_V2, "LaCie 2Big Network v2")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= netxbig_v2_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
@@ -410,7 +410,7 @@
 
 #ifdef CONFIG_MACH_NET5BIG_V2
 MACHINE_START(NET5BIG_V2, "LaCie 5Big Network v2")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= netxbig_v2_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/openrd-setup.c b/arch/arm/mach-kirkwood/openrd-setup.c
index f69beef..5660ca6 100644
--- a/arch/arm/mach-kirkwood/openrd-setup.c
+++ b/arch/arm/mach-kirkwood/openrd-setup.c
@@ -214,7 +214,7 @@
 #ifdef CONFIG_MACH_OPENRD_BASE
 MACHINE_START(OPENRD_BASE, "Marvell OpenRD Base Board")
 	/* Maintainer: Dhaval Vasa <dhaval.vasa@einfochips.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= openrd_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
@@ -226,7 +226,7 @@
 #ifdef CONFIG_MACH_OPENRD_CLIENT
 MACHINE_START(OPENRD_CLIENT, "Marvell OpenRD Client Board")
 	/* Maintainer: Dhaval Vasa <dhaval.vasa@einfochips.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= openrd_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
@@ -238,7 +238,7 @@
 #ifdef CONFIG_MACH_OPENRD_ULTIMATE
 MACHINE_START(OPENRD_ULTIMATE, "Marvell OpenRD Ultimate Board")
 	/* Maintainer: Dhaval Vasa <dhaval.vasa@einfochips.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= openrd_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c
index 75c6601..6663869 100644
--- a/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c
+++ b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c
@@ -79,7 +79,7 @@
 
 MACHINE_START(RD88F6192_NAS, "Marvell RD-88F6192-NAS Development Board")
 	/* Maintainer: Saeed Bishara <saeed@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= rd88f6192_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/rd88f6281-setup.c b/arch/arm/mach-kirkwood/rd88f6281-setup.c
index 0f75494..66b3c05 100644
--- a/arch/arm/mach-kirkwood/rd88f6281-setup.c
+++ b/arch/arm/mach-kirkwood/rd88f6281-setup.c
@@ -115,7 +115,7 @@
 
 MACHINE_START(RD88F6281, "Marvell RD-88F6281 Reference Board")
 	/* Maintainer: Saeed Bishara <saeed@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= rd88f6281_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/sheevaplug-setup.c b/arch/arm/mach-kirkwood/sheevaplug-setup.c
index 17de0bf..8b102d6 100644
--- a/arch/arm/mach-kirkwood/sheevaplug-setup.c
+++ b/arch/arm/mach-kirkwood/sheevaplug-setup.c
@@ -138,7 +138,7 @@
 #ifdef CONFIG_MACH_SHEEVAPLUG
 MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board")
 	/* Maintainer: shadi Ammouri <shadi@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= sheevaplug_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
@@ -149,7 +149,7 @@
 
 #ifdef CONFIG_MACH_ESATA_SHEEVAPLUG
 MACHINE_START(ESATA_SHEEVAPLUG, "Marvell eSATA SheevaPlug Reference Board")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= sheevaplug_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/t5325-setup.c b/arch/arm/mach-kirkwood/t5325-setup.c
index e6b9b1b..ea104fb 100644
--- a/arch/arm/mach-kirkwood/t5325-setup.c
+++ b/arch/arm/mach-kirkwood/t5325-setup.c
@@ -201,7 +201,7 @@
 
 MACHINE_START(T5325, "HP t5325 Thin Client")
 	/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= hp_t5325_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/ts219-setup.c b/arch/arm/mach-kirkwood/ts219-setup.c
index 68f32f2..262c034 100644
--- a/arch/arm/mach-kirkwood/ts219-setup.c
+++ b/arch/arm/mach-kirkwood/ts219-setup.c
@@ -132,7 +132,7 @@
 
 MACHINE_START(TS219, "QNAP TS-119/TS-219")
 	/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= qnap_ts219_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-kirkwood/ts41x-setup.c b/arch/arm/mach-kirkwood/ts41x-setup.c
index d5d0099..b68f5b4 100644
--- a/arch/arm/mach-kirkwood/ts41x-setup.c
+++ b/arch/arm/mach-kirkwood/ts41x-setup.c
@@ -176,7 +176,7 @@
 
 MACHINE_START(TS41X, "QNAP TS-41x")
 	/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= qnap_ts41x_init,
 	.map_io		= kirkwood_map_io,
 	.init_early	= kirkwood_init_early,
diff --git a/arch/arm/mach-ks8695/board-acs5k.c b/arch/arm/mach-ks8695/board-acs5k.c
index 3ca4f8e..a5fcc7c 100644
--- a/arch/arm/mach-ks8695/board-acs5k.c
+++ b/arch/arm/mach-ks8695/board-acs5k.c
@@ -223,7 +223,7 @@
 
 MACHINE_START(ACS5K, "Brivo Systems LLC ACS-5000 Master board")
 	/* Maintainer: Simtec Electronics. */
-	.boot_params	= KS8695_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ks8695_map_io,
 	.init_irq	= ks8695_init_irq,
 	.init_machine	= acs5k_init,
diff --git a/arch/arm/mach-ks8695/board-dsm320.c b/arch/arm/mach-ks8695/board-dsm320.c
index 1338cb3..fb91a71 100644
--- a/arch/arm/mach-ks8695/board-dsm320.c
+++ b/arch/arm/mach-ks8695/board-dsm320.c
@@ -121,7 +121,7 @@
 
 MACHINE_START(DSM320, "D-Link DSM-320 Wireless Media Player")
 	/* Maintainer: Simtec Electronics. */
-	.boot_params	= KS8695_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ks8695_map_io,
 	.init_irq	= ks8695_init_irq,
 	.init_machine	= dsm320_init,
diff --git a/arch/arm/mach-ks8695/board-micrel.c b/arch/arm/mach-ks8695/board-micrel.c
index e2e3cba..8f67a75 100644
--- a/arch/arm/mach-ks8695/board-micrel.c
+++ b/arch/arm/mach-ks8695/board-micrel.c
@@ -53,7 +53,7 @@
 
 MACHINE_START(KS8695, "KS8695 Centaur Development Board")
 	/* Maintainer: Micrel Semiconductor Inc. */
-	.boot_params	= KS8695_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ks8695_map_io,
 	.init_irq	= ks8695_init_irq,
 	.init_machine	= micrel_init,
diff --git a/arch/arm/mach-ks8695/include/mach/debug-macro.S b/arch/arm/mach-ks8695/include/mach/debug-macro.S
index bf516ad..a79e489 100644
--- a/arch/arm/mach-ks8695/include/mach/debug-macro.S
+++ b/arch/arm/mach-ks8695/include/mach/debug-macro.S
@@ -14,7 +14,7 @@
 #include <mach/hardware.h>
 #include <mach/regs-uart.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 		ldr	\rp, =KS8695_UART_PA		@ physical base address
 		ldr	\rv, =KS8695_UART_VA		@ virtual base address
 	.endm
diff --git a/arch/arm/mach-l7200/include/mach/debug-macro.S b/arch/arm/mach-l7200/include/mach/debug-macro.S
index b0a2db7..0b4e760 100644
--- a/arch/arm/mach-l7200/include/mach/debug-macro.S
+++ b/arch/arm/mach-l7200/include/mach/debug-macro.S
@@ -14,7 +14,7 @@
 		.equ	io_virt, IO_BASE
 		.equ	io_phys, IO_START
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00044000	@ UART1
 @		mov	\rp, #0x00045000	@ UART2
 		add	\rv, \rp, #io_virt	@ virtual address
diff --git a/arch/arm/mach-lpc32xx/include/mach/debug-macro.S b/arch/arm/mach-lpc32xx/include/mach/debug-macro.S
index 629e744..351bd6c 100644
--- a/arch/arm/mach-lpc32xx/include/mach/debug-macro.S
+++ b/arch/arm/mach-lpc32xx/include/mach/debug-macro.S
@@ -20,7 +20,7 @@
  * Debug output is hardcoded to standard UART 5
 */
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldreq	\rp, =0x40090000
 	ldrne	\rv, =0xF4090000
 	.endm
diff --git a/arch/arm/mach-lpc32xx/include/mach/memory.h b/arch/arm/mach-lpc32xx/include/mach/memory.h
deleted file mode 100644
index a647dd6..0000000
--- a/arch/arm/mach-lpc32xx/include/mach/memory.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * arch/arm/mach-lpc32xx/include/mach/memory.h
- *
- * Author: Kevin Wells <kevin.wells@nxp.com>
- *
- * Copyright (C) 2010 NXP Semiconductors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/*
- * Physical DRAM offset of bank 0
- */
-#define PLAT_PHYS_OFFSET	UL(0x80000000)
-
-#endif
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index 7993b09..9b621e1 100644
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -382,7 +382,7 @@
 
 MACHINE_START(PHY3250, "Phytec 3250 board with the LPC3250 Microcontroller")
 	/* Maintainer: Kevin Wells, NXP Semiconductors */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.map_io		= lpc32xx_map_io,
 	.init_irq	= lpc32xx_init_irq,
 	.timer		= &lpc32xx_timer,
diff --git a/arch/arm/mach-mmp/include/mach/debug-macro.S b/arch/arm/mach-mmp/include/mach/debug-macro.S
index 7e2ebd3..b6f14d2 100644
--- a/arch/arm/mach-mmp/include/mach/debug-macro.S
+++ b/arch/arm/mach-mmp/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
 
 #include <mach/addr-map.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =APB_PHYS_BASE		@ physical
 		ldr	\rv, =APB_VIRT_BASE		@ virtual
 		orr	\rp, \rp, #0x00017000
diff --git a/arch/arm/mach-mmp/include/mach/memory.h b/arch/arm/mach-mmp/include/mach/memory.h
deleted file mode 100644
index d68b50a..0000000
--- a/arch/arm/mach-mmp/include/mach/memory.h
+++ /dev/null
@@ -1,14 +0,0 @@
-/*
- * linux/arch/arm/mach-mmp/include/mach/memory.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_MACH_MEMORY_H
-#define __ASM_MACH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET	UL(0x00000000)
-
-#endif /* __ASM_MACH_MEMORY_H */
diff --git a/arch/arm/mach-msm/board-halibut.c b/arch/arm/mach-msm/board-halibut.c
index 18a3c97..16c86f8 100644
--- a/arch/arm/mach-msm/board-halibut.c
+++ b/arch/arm/mach-msm/board-halibut.c
@@ -93,7 +93,7 @@
 }
 
 MACHINE_START(HALIBUT, "Halibut Board (QCT SURF7200A)")
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.fixup		= halibut_fixup,
 	.map_io		= halibut_map_io,
 	.init_irq	= halibut_init_irq,
diff --git a/arch/arm/mach-msm/board-mahimahi.c b/arch/arm/mach-msm/board-mahimahi.c
index 7a9a03e..8a1672e 100644
--- a/arch/arm/mach-msm/board-mahimahi.c
+++ b/arch/arm/mach-msm/board-mahimahi.c
@@ -74,7 +74,7 @@
 extern struct sys_timer msm_timer;
 
 MACHINE_START(MAHIMAHI, "mahimahi")
-	.boot_params	= 0x20000100,
+	.atag_offset	= 0x100,
 	.fixup		= mahimahi_fixup,
 	.map_io		= mahimahi_map_io,
 	.init_irq	= msm_init_irq,
diff --git a/arch/arm/mach-msm/board-msm7x27.c b/arch/arm/mach-msm/board-msm7x27.c
index c03f269..a807655 100644
--- a/arch/arm/mach-msm/board-msm7x27.c
+++ b/arch/arm/mach-msm/board-msm7x27.c
@@ -130,7 +130,7 @@
 }
 
 MACHINE_START(MSM7X27_SURF, "QCT MSM7x27 SURF")
-	.boot_params	= PLAT_PHYS_OFFSET + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= msm7x2x_map_io,
 	.init_irq	= msm7x2x_init_irq,
 	.init_machine	= msm7x2x_init,
@@ -138,7 +138,7 @@
 MACHINE_END
 
 MACHINE_START(MSM7X27_FFA, "QCT MSM7x27 FFA")
-	.boot_params	= PLAT_PHYS_OFFSET + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= msm7x2x_map_io,
 	.init_irq	= msm7x2x_init_irq,
 	.init_machine	= msm7x2x_init,
@@ -146,7 +146,7 @@
 MACHINE_END
 
 MACHINE_START(MSM7X25_SURF, "QCT MSM7x25 SURF")
-	.boot_params	= PLAT_PHYS_OFFSET + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= msm7x2x_map_io,
 	.init_irq	= msm7x2x_init_irq,
 	.init_machine	= msm7x2x_init,
@@ -154,7 +154,7 @@
 MACHINE_END
 
 MACHINE_START(MSM7X25_FFA, "QCT MSM7x25 FFA")
-	.boot_params	= PLAT_PHYS_OFFSET + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= msm7x2x_map_io,
 	.init_irq	= msm7x2x_init_irq,
 	.init_machine	= msm7x2x_init,
diff --git a/arch/arm/mach-msm/board-msm7x30.c b/arch/arm/mach-msm/board-msm7x30.c
index b7a8496..bb72ea0 100644
--- a/arch/arm/mach-msm/board-msm7x30.c
+++ b/arch/arm/mach-msm/board-msm7x30.c
@@ -24,6 +24,7 @@
 #include <linux/smsc911x.h>
 #include <linux/usb/msm_hsusb.h>
 #include <linux/clkdev.h>
+#include <linux/memblock.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -42,6 +43,21 @@
 
 extern struct sys_timer msm_timer;
 
+static void __init msm7x30_fixup(struct machine_desc *desc, struct tag *tag,
+			 char **cmdline, struct meminfo *mi)
+{
+	for (; tag->hdr.size; tag = tag_next(tag))
+		if (tag->hdr.tag == ATAG_MEM && tag->u.mem.start == 0x200000) {
+			tag->u.mem.start = 0;
+			tag->u.mem.size += SZ_2M;
+		}
+}
+
+static void __init msm7x30_reserve(void)
+{
+	memblock_remove(0x0, SZ_2M);
+}
+
 static int hsusb_phy_init_seq[] = {
 	0x30, 0x32,	/* Enable and set Pre-Emphasis Depth to 20% */
 	0x02, 0x36,	/* Disable CDR Auto Reset feature */
@@ -106,7 +122,9 @@
 }
 
 MACHINE_START(MSM7X30_SURF, "QCT MSM7X30 SURF")
-	.boot_params = PLAT_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
+	.fixup = msm7x30_fixup,
+	.reserve = msm7x30_reserve,
 	.map_io = msm7x30_map_io,
 	.init_irq = msm7x30_init_irq,
 	.init_machine = msm7x30_init,
@@ -114,7 +132,9 @@
 MACHINE_END
 
 MACHINE_START(MSM7X30_FFA, "QCT MSM7X30 FFA")
-	.boot_params = PLAT_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
+	.fixup = msm7x30_fixup,
+	.reserve = msm7x30_reserve,
 	.map_io = msm7x30_map_io,
 	.init_irq = msm7x30_init_irq,
 	.init_machine = msm7x30_init,
@@ -122,7 +142,9 @@
 MACHINE_END
 
 MACHINE_START(MSM7X30_FLUID, "QCT MSM7X30 FLUID")
-	.boot_params = PLAT_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
+	.fixup = msm7x30_fixup,
+	.reserve = msm7x30_reserve,
 	.map_io = msm7x30_map_io,
 	.init_irq = msm7x30_init_irq,
 	.init_machine = msm7x30_init,
diff --git a/arch/arm/mach-msm/board-msm8960.c b/arch/arm/mach-msm/board-msm8960.c
index 35c7cee..b04468e 100644
--- a/arch/arm/mach-msm/board-msm8960.c
+++ b/arch/arm/mach-msm/board-msm8960.c
@@ -20,16 +20,34 @@
 #include <linux/io.h>
 #include <linux/irq.h>
 #include <linux/clkdev.h>
+#include <linux/memblock.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/hardware/gic.h>
+#include <asm/setup.h>
 
 #include <mach/board.h>
 #include <mach/msm_iomap.h>
 
 #include "devices.h"
 
+static void __init msm8960_fixup(struct machine_desc *desc, struct tag *tag,
+			 char **cmdline, struct meminfo *mi)
+{
+	for (; tag->hdr.size; tag = tag_next(tag))
+		if (tag->hdr.tag == ATAG_MEM &&
+				tag->u.mem.start == 0x40200000) {
+			tag->u.mem.start = 0x40000000;
+			tag->u.mem.size += SZ_2M;
+		}
+}
+
+static void __init msm8960_reserve(void)
+{
+	memblock_remove(0x40000000, SZ_2M);
+}
+
 static void __init msm8960_map_io(void)
 {
 	msm_map_msm8960_io();
@@ -76,6 +94,8 @@
 }
 
 MACHINE_START(MSM8960_SIM, "QCT MSM8960 SIMULATOR")
+	.fixup = msm8960_fixup,
+	.reserve = msm8960_reserve,
 	.map_io = msm8960_map_io,
 	.init_irq = msm8960_init_irq,
 	.timer = &msm_timer,
@@ -83,6 +103,8 @@
 MACHINE_END
 
 MACHINE_START(MSM8960_RUMI3, "QCT MSM8960 RUMI3")
+	.fixup = msm8960_fixup,
+	.reserve = msm8960_reserve,
 	.map_io = msm8960_map_io,
 	.init_irq = msm8960_init_irq,
 	.timer = &msm_timer,
diff --git a/arch/arm/mach-msm/board-msm8x60.c b/arch/arm/mach-msm/board-msm8x60.c
index 1163b6f..106170f 100644
--- a/arch/arm/mach-msm/board-msm8x60.c
+++ b/arch/arm/mach-msm/board-msm8x60.c
@@ -20,14 +20,31 @@
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/irq.h>
+#include <linux/memblock.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/hardware/gic.h>
+#include <asm/setup.h>
 
 #include <mach/board.h>
 #include <mach/msm_iomap.h>
 
+static void __init msm8x60_fixup(struct machine_desc *desc, struct tag *tag,
+			 char **cmdline, struct meminfo *mi)
+{
+	for (; tag->hdr.size; tag = tag_next(tag))
+		if (tag->hdr.tag == ATAG_MEM &&
+				tag->u.mem.start == 0x40200000) {
+			tag->u.mem.start = 0x40000000;
+			tag->u.mem.size += SZ_2M;
+		}
+}
+
+static void __init msm8x60_reserve(void)
+{
+	memblock_remove(0x40000000, SZ_2M);
+}
 
 static void __init msm8x60_map_io(void)
 {
@@ -36,8 +53,6 @@
 
 static void __init msm8x60_init_irq(void)
 {
-	unsigned int i;
-
 	gic_init(0, GIC_PPI_START, MSM_QGIC_DIST_BASE,
 		 (void *)MSM_QGIC_CPU_BASE);
 
@@ -49,15 +64,6 @@
 	 */
 	if (!machine_is_msm8x60_sim())
 		writel(0x0000FFFF, MSM_QGIC_DIST_BASE + GIC_DIST_ENABLE_SET);
-
-	/* FIXME: Not installing AVS_SVICINT and AVS_SVICINTSWDONE yet
-	 * as they are configured as level, which does not play nice with
-	 * handle_percpu_irq.
-	 */
-	for (i = GIC_PPI_START; i < GIC_SPI_START; i++) {
-		if (i != AVS_SVICINT && i != AVS_SVICINTSWDONE)
-			irq_set_handler(i, handle_percpu_irq);
-	}
 }
 
 static void __init msm8x60_init(void)
@@ -65,6 +71,8 @@
 }
 
 MACHINE_START(MSM8X60_RUMI3, "QCT MSM8X60 RUMI3")
+	.fixup = msm8x60_fixup,
+	.reserve = msm8x60_reserve,
 	.map_io = msm8x60_map_io,
 	.init_irq = msm8x60_init_irq,
 	.init_machine = msm8x60_init,
@@ -72,6 +80,8 @@
 MACHINE_END
 
 MACHINE_START(MSM8X60_SURF, "QCT MSM8X60 SURF")
+	.fixup = msm8x60_fixup,
+	.reserve = msm8x60_reserve,
 	.map_io = msm8x60_map_io,
 	.init_irq = msm8x60_init_irq,
 	.init_machine = msm8x60_init,
@@ -79,6 +89,8 @@
 MACHINE_END
 
 MACHINE_START(MSM8X60_SIM, "QCT MSM8X60 SIMULATOR")
+	.fixup = msm8x60_fixup,
+	.reserve = msm8x60_reserve,
 	.map_io = msm8x60_map_io,
 	.init_irq = msm8x60_init_irq,
 	.init_machine = msm8x60_init,
@@ -86,6 +98,8 @@
 MACHINE_END
 
 MACHINE_START(MSM8X60_FFA, "QCT MSM8X60 FFA")
+	.fixup = msm8x60_fixup,
+	.reserve = msm8x60_reserve,
 	.map_io = msm8x60_map_io,
 	.init_irq = msm8x60_init_irq,
 	.init_machine = msm8x60_init,
diff --git a/arch/arm/mach-msm/board-qsd8x50.c b/arch/arm/mach-msm/board-qsd8x50.c
index 6a96911..51109b1 100644
--- a/arch/arm/mach-msm/board-qsd8x50.c
+++ b/arch/arm/mach-msm/board-qsd8x50.c
@@ -193,7 +193,7 @@
 }
 
 MACHINE_START(QSD8X50_SURF, "QCT QSD8X50 SURF")
-	.boot_params = PLAT_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = qsd8x50_map_io,
 	.init_irq = qsd8x50_init_irq,
 	.init_machine = qsd8x50_init,
@@ -201,7 +201,7 @@
 MACHINE_END
 
 MACHINE_START(QSD8X50A_ST1_5, "QCT QSD8X50A ST1.5")
-	.boot_params = PLAT_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = qsd8x50_map_io,
 	.init_irq = qsd8x50_init_irq,
 	.init_machine = qsd8x50_init,
diff --git a/arch/arm/mach-msm/board-sapphire.c b/arch/arm/mach-msm/board-sapphire.c
index 68f930f..dc0bcb5 100644
--- a/arch/arm/mach-msm/board-sapphire.c
+++ b/arch/arm/mach-msm/board-sapphire.c
@@ -105,7 +105,7 @@
 
 MACHINE_START(SAPPHIRE, "sapphire")
 /* Maintainer: Brian Swetland <swetland@google.com> */
-	.boot_params    = PLAT_PHYS_OFFSET + 0x100,
+	.atag_offset    = 0x100,
 	.fixup          = sapphire_fixup,
 	.map_io         = sapphire_map_io,
 	.init_irq       = sapphire_init_irq,
diff --git a/arch/arm/mach-msm/board-trout.c b/arch/arm/mach-msm/board-trout.c
index 8143867..22d5694 100644
--- a/arch/arm/mach-msm/board-trout.c
+++ b/arch/arm/mach-msm/board-trout.c
@@ -93,7 +93,7 @@
 }
 
 MACHINE_START(TROUT, "HTC Dream")
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.fixup		= trout_fixup,
 	.map_io		= trout_map_io,
 	.init_irq	= trout_init_irq,
diff --git a/arch/arm/mach-msm/include/mach/debug-macro.S b/arch/arm/mach-msm/include/mach/debug-macro.S
index 646b99e..2dc73cc 100644
--- a/arch/arm/mach-msm/include/mach/debug-macro.S
+++ b/arch/arm/mach-msm/include/mach/debug-macro.S
@@ -20,7 +20,7 @@
 #include <mach/msm_iomap.h>
 
 #if defined(CONFIG_HAS_MSM_DEBUG_UART_PHYS) && !defined(CONFIG_MSM_DEBUG_UART_NONE)
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =MSM_DEBUG_UART_PHYS
 	ldr	\rv, =MSM_DEBUG_UART_BASE
 	.endm
@@ -37,7 +37,7 @@
 	beq	1001b
 	.endm
 #else
-	.macro  addruart, rp, rv
+	.macro  addruart, rp, rv, tmp
 	mov	\rv, #0xff000000
 	orr	\rv, \rv, #0x00f00000
 	.endm
diff --git a/arch/arm/mach-msm/include/mach/entry-macro-qgic.S b/arch/arm/mach-msm/include/mach/entry-macro-qgic.S
index 1246715..717076f 100644
--- a/arch/arm/mach-msm/include/mach/entry-macro-qgic.S
+++ b/arch/arm/mach-msm/include/mach/entry-macro-qgic.S
@@ -8,81 +8,10 @@
  * warranty of any kind, whether express or implied.
  */
 
-#include <mach/hardware.h>
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
 
 	.macro	disable_fiq
 	.endm
 
-	.macro  get_irqnr_preamble, base, tmp
-	ldr	\base, =gic_cpu_base_addr
-	ldr	\base, [\base]
-	.endm
-
 	.macro  arch_ret_to_user, tmp1, tmp2
 	.endm
-
-	/*
-	 * The interrupt numbering scheme is defined in the
-	 * interrupt controller spec.  To wit:
-	 *
-	 * Migrated the code from ARM MP port to be more consistent
-	 * with interrupt processing , the following still holds true
-	 * however, all interrupts are treated the same regardless of
-	 * if they are local IPI or PPI
-	 *
-	 * Interrupts 0-15 are IPI
-	 * 16-31 are PPI
-	 *   (16-18 are the timers)
-	 * 32-1020 are global
-	 * 1021-1022 are reserved
-	 * 1023 is "spurious" (no interrupt)
-	 *
-	 * A simple read from the controller will tell us the number of the
-	 * highest priority enabled interrupt.  We then just need to check
-	 * whether it is in the valid range for an IRQ (0-1020 inclusive).
-	 *
-	 * Base ARM code assumes that the local (private) peripheral interrupts
-	 * are not valid, we treat them differently, in that the privates are
-	 * handled like normal shared interrupts with the exception that only
-	 * one processor can register the interrupt and the handler must be
-	 * the same for all processors.
-	 */
-
-	.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-
-	ldr  \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 =srcCPU,
-						   9-0 =int # */
-
-	bic     \irqnr, \irqstat, #0x1c00	@mask src
-	cmp     \irqnr, #15
-	ldr		\tmp, =1021
-	cmpcc	\irqnr, \irqnr
-	cmpne	\irqnr, \tmp
-	cmpcs	\irqnr, \irqnr
-
-	.endm
-
-	/* We assume that irqstat (the raw value of the IRQ acknowledge
-	 * register) is preserved from the macro above.
-	 * If there is an IPI, we immediately signal end of interrupt on the
-	 * controller, since this requires the original irqstat value which
-	 * we won't easily be able to recreate later.
-	 */
-	.macro test_for_ipi, irqnr, irqstat, base, tmp
-    bic \irqnr, \irqstat, #0x1c00
-    cmp \irqnr, #16
-    strcc   \irqstat, [\base, #GIC_CPU_EOI]
-    cmpcs   \irqnr, \irqnr
-	.endm
-
-	/* As above, this assumes that irqstat and base are preserved.. */
-
-	.macro test_for_ltirq, irqnr, irqstat, base, tmp
-    bic \irqnr, \irqstat, #0x1c00
-    mov     \tmp, #0
-    cmp \irqnr, #16
-    moveq   \tmp, #1
-    streq   \irqstat, [\base, #GIC_CPU_EOI]
-    cmp \tmp, #0
-	.endm
diff --git a/arch/arm/mach-msm/include/mach/memory.h b/arch/arm/mach-msm/include/mach/memory.h
deleted file mode 100644
index f2f8d29..0000000
--- a/arch/arm/mach-msm/include/mach/memory.h
+++ /dev/null
@@ -1,35 +0,0 @@
-/* arch/arm/mach-msm/include/mach/memory.h
- *
- * Copyright (C) 2007 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/* physical offset of RAM */
-#if defined(CONFIG_ARCH_QSD8X50) && defined(CONFIG_MSM_SOC_REV_A)
-#define PLAT_PHYS_OFFSET		UL(0x00000000)
-#elif defined(CONFIG_ARCH_QSD8X50)
-#define PLAT_PHYS_OFFSET		UL(0x20000000)
-#elif defined(CONFIG_ARCH_MSM7X30)
-#define PLAT_PHYS_OFFSET		UL(0x00200000)
-#elif defined(CONFIG_ARCH_MSM8X60)
-#define PLAT_PHYS_OFFSET		UL(0x40200000)
-#elif defined(CONFIG_ARCH_MSM8960)
-#define PLAT_PHYS_OFFSET		UL(0x40200000)
-#else
-#define PLAT_PHYS_OFFSET		UL(0x10000000)
-#endif
-
-#endif
-
diff --git a/arch/arm/mach-msm/platsmp.c b/arch/arm/mach-msm/platsmp.c
index 1a1af9e..7276595 100644
--- a/arch/arm/mach-msm/platsmp.c
+++ b/arch/arm/mach-msm/platsmp.c
@@ -156,6 +156,12 @@
 {
 	unsigned int i, ncores = get_core_count();
 
+	if (ncores > nr_cpu_ids) {
+		pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+			ncores, nr_cpu_ids);
+		ncores = nr_cpu_ids;
+	}
+
 	for (i = 0; i < ncores; i++)
 		set_cpu_possible(i, true);
 
diff --git a/arch/arm/mach-msm/timer.c b/arch/arm/mach-msm/timer.c
index 63621f1..afeeca5 100644
--- a/arch/arm/mach-msm/timer.c
+++ b/arch/arm/mach-msm/timer.c
@@ -71,12 +71,16 @@
 struct msm_clock {
 	struct clock_event_device   clockevent;
 	struct clocksource          clocksource;
-	struct irqaction            irq;
+	unsigned int		    irq;
 	void __iomem                *regbase;
 	uint32_t                    freq;
 	uint32_t                    shift;
 	void __iomem                *global_counter;
 	void __iomem                *local_counter;
+	union {
+		struct clock_event_device		*evt;
+		struct clock_event_device __percpu	**percpu_evt;
+	};		
 };
 
 enum {
@@ -87,13 +91,10 @@
 
 
 static struct msm_clock msm_clocks[];
-static struct clock_event_device *local_clock_event;
 
 static irqreturn_t msm_timer_interrupt(int irq, void *dev_id)
 {
-	struct clock_event_device *evt = dev_id;
-	if (smp_processor_id() != 0)
-		evt = local_clock_event;
+	struct clock_event_device *evt = *(struct clock_event_device **)dev_id;
 	if (evt->event_handler == NULL)
 		return IRQ_HANDLED;
 	evt->event_handler(evt);
@@ -171,13 +172,7 @@
 			.mask           = CLOCKSOURCE_MASK(32),
 			.flags          = CLOCK_SOURCE_IS_CONTINUOUS,
 		},
-		.irq = {
-			.name    = "gp_timer",
-			.flags   = IRQF_DISABLED | IRQF_TIMER | IRQF_TRIGGER_RISING,
-			.handler = msm_timer_interrupt,
-			.dev_id  = &msm_clocks[0].clockevent,
-			.irq     = INT_GP_TIMER_EXP
-		},
+		.irq = INT_GP_TIMER_EXP,
 		.freq = GPT_HZ,
 	},
 	[MSM_CLOCK_DGT] = {
@@ -196,13 +191,7 @@
 			.mask           = CLOCKSOURCE_MASK((32 - MSM_DGT_SHIFT)),
 			.flags          = CLOCK_SOURCE_IS_CONTINUOUS,
 		},
-		.irq = {
-			.name    = "dg_timer",
-			.flags   = IRQF_DISABLED | IRQF_TIMER | IRQF_TRIGGER_RISING,
-			.handler = msm_timer_interrupt,
-			.dev_id  = &msm_clocks[1].clockevent,
-			.irq     = INT_DEBUG_TIMER_EXP
-		},
+		.irq = INT_DEBUG_TIMER_EXP,
 		.freq = DGT_HZ >> MSM_DGT_SHIFT,
 		.shift = MSM_DGT_SHIFT,
 	}
@@ -261,10 +250,30 @@
 			printk(KERN_ERR "msm_timer_init: clocksource_register "
 			       "failed for %s\n", cs->name);
 
-		res = setup_irq(clock->irq.irq, &clock->irq);
+		ce->irq = clock->irq;
+		if (cpu_is_msm8x60() || cpu_is_msm8960()) {
+			clock->percpu_evt = alloc_percpu(struct clock_event_device *);
+			if (!clock->percpu_evt) {
+				pr_err("msm_timer_init: memory allocation "
+				       "failed for %s\n", ce->name);
+				continue;
+			}
+
+			*__this_cpu_ptr(clock->percpu_evt) = ce;
+			res = request_percpu_irq(ce->irq, msm_timer_interrupt,
+						 ce->name, clock->percpu_evt);
+			if (!res)
+				enable_percpu_irq(ce->irq, 0);
+		} else {
+			clock->evt = ce;
+			res = request_irq(ce->irq, msm_timer_interrupt,
+					  IRQF_TIMER | IRQF_NOBALANCING | IRQF_TRIGGER_RISING,
+					  ce->name, &clock->evt);
+		}
+
 		if (res)
-			printk(KERN_ERR "msm_timer_init: setup_irq "
-			       "failed for %s\n", cs->name);
+			pr_err("msm_timer_init: request_irq failed for %s\n",
+			       ce->name);
 
 		clockevents_register_device(ce);
 	}
@@ -273,6 +282,7 @@
 #ifdef CONFIG_SMP
 int __cpuinit local_timer_setup(struct clock_event_device *evt)
 {
+	static bool local_timer_inited;
 	struct msm_clock *clock = &msm_clocks[MSM_GLOBAL_TIMER];
 
 	/* Use existing clock_event for cpu 0 */
@@ -281,12 +291,13 @@
 
 	writel(DGT_CLK_CTL_DIV_4, MSM_TMR_BASE + DGT_CLK_CTL);
 
-	if (!local_clock_event) {
+	if (!local_timer_inited) {
 		writel(0, clock->regbase  + TIMER_ENABLE);
 		writel(0, clock->regbase + TIMER_CLEAR);
 		writel(~0, clock->regbase + TIMER_MATCH_VAL);
+		local_timer_inited = true;
 	}
-	evt->irq = clock->irq.irq;
+	evt->irq = clock->irq;
 	evt->name = "local_timer";
 	evt->features = CLOCK_EVT_FEAT_ONESHOT;
 	evt->rating = clock->clockevent.rating;
@@ -298,17 +309,17 @@
 		clockevent_delta2ns(0xf0000000 >> clock->shift, evt);
 	evt->min_delta_ns = clockevent_delta2ns(4, evt);
 
-	local_clock_event = evt;
-
-	gic_enable_ppi(clock->irq.irq);
+	*__this_cpu_ptr(clock->percpu_evt) = evt;
+	enable_percpu_irq(evt->irq, 0);
 
 	clockevents_register_device(evt);
 	return 0;
 }
 
-inline int local_timer_ack(void)
+void local_timer_stop(struct clock_event_device *evt)
 {
-	return 1;
+	evt->set_mode(CLOCK_EVT_MODE_UNUSED, evt);
+	disable_percpu_irq(evt->irq);
 }
 
 #endif
diff --git a/arch/arm/mach-mv78xx0/buffalo-wxl-setup.c b/arch/arm/mach-mv78xx0/buffalo-wxl-setup.c
index 20f3f12..0e94268 100644
--- a/arch/arm/mach-mv78xx0/buffalo-wxl-setup.c
+++ b/arch/arm/mach-mv78xx0/buffalo-wxl-setup.c
@@ -145,7 +145,7 @@
 
 MACHINE_START(TERASTATION_WXL, "Buffalo Nas WXL")
 	/* Maintainer: Sebastien Requiem <sebastien@requiem.fr> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= wxl_init,
 	.map_io		= mv78xx0_map_io,
 	.init_early	= mv78xx0_init_early,
diff --git a/arch/arm/mach-mv78xx0/db78x00-bp-setup.c b/arch/arm/mach-mv78xx0/db78x00-bp-setup.c
index df5aebe..50b85ae 100644
--- a/arch/arm/mach-mv78xx0/db78x00-bp-setup.c
+++ b/arch/arm/mach-mv78xx0/db78x00-bp-setup.c
@@ -93,7 +93,7 @@
 
 MACHINE_START(DB78X00_BP, "Marvell DB-78x00-BP Development Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= db78x00_init,
 	.map_io		= mv78xx0_map_io,
 	.init_early	= mv78xx0_init_early,
diff --git a/arch/arm/mach-mv78xx0/include/mach/debug-macro.S b/arch/arm/mach-mv78xx0/include/mach/debug-macro.S
index 04891428..a7df02b 100644
--- a/arch/arm/mach-mv78xx0/include/mach/debug-macro.S
+++ b/arch/arm/mach-mv78xx0/include/mach/debug-macro.S
@@ -8,7 +8,7 @@
 
 #include <mach/mv78xx0.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =MV78XX0_REGS_PHYS_BASE
 	ldr	\rv, =MV78XX0_REGS_VIRT_BASE
 	orr	\rp, \rp, #0x00012000
diff --git a/arch/arm/mach-mv78xx0/include/mach/memory.h b/arch/arm/mach-mv78xx0/include/mach/memory.h
deleted file mode 100644
index a648c51..0000000
--- a/arch/arm/mach-mv78xx0/include/mach/memory.h
+++ /dev/null
@@ -1,10 +0,0 @@
-/*
- * arch/arm/mach-mv78xx0/include/mach/memory.h
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET		UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-mv78xx0/rd78x00-masa-setup.c b/arch/arm/mach-mv78xx0/rd78x00-masa-setup.c
index d927f14..e85222e 100644
--- a/arch/arm/mach-mv78xx0/rd78x00-masa-setup.c
+++ b/arch/arm/mach-mv78xx0/rd78x00-masa-setup.c
@@ -78,7 +78,7 @@
 
 MACHINE_START(RD78X00_MASA, "Marvell RD-78x00-MASA Development Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= rd78x00_masa_init,
 	.map_io		= mv78xx0_map_io,
 	.init_early	= mv78xx0_init_early,
diff --git a/arch/arm/mach-mx5/board-cpuimx51.c b/arch/arm/mach-mx5/board-cpuimx51.c
index e28d0e1..1fc1103 100644
--- a/arch/arm/mach-mx5/board-cpuimx51.c
+++ b/arch/arm/mach-mx5/board-cpuimx51.c
@@ -290,7 +290,7 @@
 
 MACHINE_START(EUKREA_CPUIMX51, "Eukrea CPUIMX51 Module")
 	/* Maintainer: Eric Bénard <eric@eukrea.com> */
-	.boot_params = MX51_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx51_map_io,
 	.init_early = imx51_init_early,
 	.init_irq = mx51_init_irq,
diff --git a/arch/arm/mach-mx5/board-cpuimx51sd.c b/arch/arm/mach-mx5/board-cpuimx51sd.c
index 5276660..52a11c1 100644
--- a/arch/arm/mach-mx5/board-cpuimx51sd.c
+++ b/arch/arm/mach-mx5/board-cpuimx51sd.c
@@ -328,7 +328,7 @@
 
 MACHINE_START(EUKREA_CPUIMX51SD, "Eukrea CPUIMX51SD")
 	/* Maintainer: Eric Bénard <eric@eukrea.com> */
-	.boot_params = MX51_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx51_map_io,
 	.init_early = imx51_init_early,
 	.init_irq = mx51_init_irq,
diff --git a/arch/arm/mach-mx5/board-mx51_3ds.c b/arch/arm/mach-mx5/board-mx51_3ds.c
index 067d8c4..0578390 100644
--- a/arch/arm/mach-mx5/board-mx51_3ds.c
+++ b/arch/arm/mach-mx5/board-mx51_3ds.c
@@ -168,7 +168,7 @@
 
 MACHINE_START(MX51_3DS, "Freescale MX51 3-Stack Board")
 	/* Maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX51_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx51_map_io,
 	.init_early = imx51_init_early,
 	.init_irq = mx51_init_irq,
diff --git a/arch/arm/mach-mx5/board-mx51_babbage.c b/arch/arm/mach-mx5/board-mx51_babbage.c
index 4231d98..5993208 100644
--- a/arch/arm/mach-mx5/board-mx51_babbage.c
+++ b/arch/arm/mach-mx5/board-mx51_babbage.c
@@ -414,7 +414,7 @@
 
 MACHINE_START(MX51_BABBAGE, "Freescale MX51 Babbage Board")
 	/* Maintainer: Amit Kucheria <amit.kucheria@canonical.com> */
-	.boot_params = MX51_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx51_map_io,
 	.init_early = imx51_init_early,
 	.init_irq = mx51_init_irq,
diff --git a/arch/arm/mach-mx5/board-mx51_efikamx.c b/arch/arm/mach-mx5/board-mx51_efikamx.c
index 90ae903..a9e4866 100644
--- a/arch/arm/mach-mx5/board-mx51_efikamx.c
+++ b/arch/arm/mach-mx5/board-mx51_efikamx.c
@@ -285,7 +285,7 @@
 
 MACHINE_START(MX51_EFIKAMX, "Genesi EfikaMX nettop")
 	/* Maintainer: Amit Kucheria <amit.kucheria@linaro.org> */
-	.boot_params = MX51_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx51_map_io,
 	.init_early = imx51_init_early,
 	.init_irq = mx51_init_irq,
diff --git a/arch/arm/mach-mx5/board-mx51_efikasb.c b/arch/arm/mach-mx5/board-mx51_efikasb.c
index c26508a6..38c4a3e 100644
--- a/arch/arm/mach-mx5/board-mx51_efikasb.c
+++ b/arch/arm/mach-mx5/board-mx51_efikasb.c
@@ -280,7 +280,7 @@
 };
 
 MACHINE_START(MX51_EFIKASB, "Genesi Efika Smartbook")
-	.boot_params = MX51_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx51_map_io,
 	.init_early = imx51_init_early,
 	.init_irq = mx51_init_irq,
diff --git a/arch/arm/mach-mxs/include/mach/debug-macro.S b/arch/arm/mach-mxs/include/mach/debug-macro.S
index 79650a1..714570d 100644
--- a/arch/arm/mach-mxs/include/mach/debug-macro.S
+++ b/arch/arm/mach-mxs/include/mach/debug-macro.S
@@ -30,7 +30,7 @@
 
 #define UART_VADDR	MXS_IO_ADDRESS(UART_PADDR)
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =UART_PADDR	@ physical
 		ldr	\rv, =UART_VADDR	@ virtual
 		.endm
diff --git a/arch/arm/mach-mxs/include/mach/memory.h b/arch/arm/mach-mxs/include/mach/memory.h
deleted file mode 100644
index b5420a5..0000000
--- a/arch/arm/mach-mxs/include/mach/memory.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
- */
-
-#ifndef __MACH_MXS_MEMORY_H__
-#define __MACH_MXS_MEMORY_H__
-
-#define PHYS_OFFSET		UL(0x40000000)
-
-#endif /* __MACH_MXS_MEMORY_H__ */
diff --git a/arch/arm/mach-netx/include/mach/debug-macro.S b/arch/arm/mach-netx/include/mach/debug-macro.S
index 56a9152..247781e 100644
--- a/arch/arm/mach-netx/include/mach/debug-macro.S
+++ b/arch/arm/mach-netx/include/mach/debug-macro.S
@@ -13,7 +13,7 @@
 
 #include "hardware.h"
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00000a00
 		orr	\rv, \rp, #io_p2v(0x00100000)	@ virtual
 		orr	\rp, \rp, #0x00100000		@ physical
diff --git a/arch/arm/mach-netx/include/mach/memory.h b/arch/arm/mach-netx/include/mach/memory.h
deleted file mode 100644
index 5956149..0000000
--- a/arch/arm/mach-netx/include/mach/memory.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- *  arch/arm/mach-netx/include/mach/memory.h
- *
- * Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2
- * as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET UL(0x80000000)
-
-#endif
-
diff --git a/arch/arm/mach-netx/nxdb500.c b/arch/arm/mach-netx/nxdb500.c
index ca8b203..90903dd 100644
--- a/arch/arm/mach-netx/nxdb500.c
+++ b/arch/arm/mach-netx/nxdb500.c
@@ -200,7 +200,7 @@
 }
 
 MACHINE_START(NXDB500, "Hilscher nxdb500")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.map_io		= netx_map_io,
 	.init_irq	= netx_init_irq,
 	.timer		= &netx_timer,
diff --git a/arch/arm/mach-netx/nxdkn.c b/arch/arm/mach-netx/nxdkn.c
index d775cbe..c63384a 100644
--- a/arch/arm/mach-netx/nxdkn.c
+++ b/arch/arm/mach-netx/nxdkn.c
@@ -93,7 +93,7 @@
 }
 
 MACHINE_START(NXDKN, "Hilscher nxdkn")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.map_io		= netx_map_io,
 	.init_irq	= netx_init_irq,
 	.timer		= &netx_timer,
diff --git a/arch/arm/mach-netx/nxeb500hmi.c b/arch/arm/mach-netx/nxeb500hmi.c
index de369cd..8f548ec 100644
--- a/arch/arm/mach-netx/nxeb500hmi.c
+++ b/arch/arm/mach-netx/nxeb500hmi.c
@@ -177,7 +177,7 @@
 }
 
 MACHINE_START(NXEB500HMI, "Hilscher nxeb500hmi")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.map_io		= netx_map_io,
 	.init_irq	= netx_init_irq,
 	.timer		= &netx_timer,
diff --git a/arch/arm/mach-nomadik/board-nhk8815.c b/arch/arm/mach-nomadik/board-nhk8815.c
index 1399303..398a75f 100644
--- a/arch/arm/mach-nomadik/board-nhk8815.c
+++ b/arch/arm/mach-nomadik/board-nhk8815.c
@@ -276,7 +276,7 @@
 
 MACHINE_START(NOMADIK, "NHK8815")
 	/* Maintainer: ST MicroElectronics */
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= cpu8815_map_io,
 	.init_irq	= cpu8815_init_irq,
 	.timer		= &nomadik_timer,
diff --git a/arch/arm/mach-nomadik/include/mach/debug-macro.S b/arch/arm/mach-nomadik/include/mach/debug-macro.S
index e7151b4..7354179 100644
--- a/arch/arm/mach-nomadik/include/mach/debug-macro.S
+++ b/arch/arm/mach-nomadik/include/mach/debug-macro.S
@@ -10,7 +10,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00100000
 		add	\rp, \rp, #0x000fb000
 		add	\rv, \rp, #0xf0000000	@ virtual base
diff --git a/arch/arm/mach-nomadik/include/mach/memory.h b/arch/arm/mach-nomadik/include/mach/memory.h
deleted file mode 100644
index d332521..0000000
--- a/arch/arm/mach-nomadik/include/mach/memory.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- *  mach-nomadik/include/mach/memory.h
- *
- *  Copyright (C) 1999 ARM Limited
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET	UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-nuc93x/include/mach/memory.h b/arch/arm/mach-nuc93x/include/mach/memory.h
deleted file mode 100644
index ef9864b..0000000
--- a/arch/arm/mach-nuc93x/include/mach/memory.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * arch/arm/mach-nuc93x/include/mach/memory.h
- *
- * Copyright (c) 2008 Nuvoton technology corporation
- * All rights reserved.
- *
- * Wan ZongShun <mcuos.com@gmail.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET	UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-nuc93x/mach-nuc932evb.c b/arch/arm/mach-nuc93x/mach-nuc932evb.c
index d702570..1f741b1 100644
--- a/arch/arm/mach-nuc93x/mach-nuc932evb.c
+++ b/arch/arm/mach-nuc93x/mach-nuc932evb.c
@@ -35,7 +35,6 @@
 
 MACHINE_START(NUC932EVB, "NUC932EVB")
 	/* Maintainer: Wan ZongShun */
-	.boot_params	= 0,
 	.map_io		= nuc932evb_map_io,
 	.init_irq	= nuc93x_init_irq,
 	.init_machine	= nuc932evb_init,
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 312ea6b..eb36b25 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -386,7 +386,7 @@
 
 MACHINE_START(AMS_DELTA, "Amstrad E3 (Delta)")
 	/* Maintainer: Jonathan McDowell <noodles@earth.li> */
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= ams_delta_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= ams_delta_init_irq,
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index a6b1bea..999789c 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -389,7 +389,7 @@
 
 MACHINE_START(OMAP_FSAMPLE, "OMAP730 F-Sample")
 /* Maintainer: Brian Swetland <swetland@google.com> */
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= omap_fsample_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= omap_fsample_init_irq,
diff --git a/arch/arm/mach-omap1/board-generic.c b/arch/arm/mach-omap1/board-generic.c
index 04fc356..23cc9e4 100644
--- a/arch/arm/mach-omap1/board-generic.c
+++ b/arch/arm/mach-omap1/board-generic.c
@@ -94,7 +94,7 @@
 
 MACHINE_START(OMAP_GENERIC, "Generic OMAP1510/1610/1710")
 	/* Maintainer: Tony Lindgren <tony@atomide.com> */
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= omap_generic_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= omap_generic_init_irq,
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index cb7fb1a..6c70c28 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c
@@ -461,7 +461,7 @@
 
 MACHINE_START(OMAP_H2, "TI-H2")
 	/* Maintainer: Imre Deak <imre.deak@nokia.com> */
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= h2_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= h2_init_irq,
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index 31f3487..8e2b64a 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -449,7 +449,7 @@
 
 MACHINE_START(OMAP_H3, "TI OMAP1710 H3 board")
 	/* Maintainer: Texas Instruments, Inc. */
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= h3_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= h3_init_irq,
diff --git a/arch/arm/mach-omap1/board-htcherald.c b/arch/arm/mach-omap1/board-htcherald.c
index 36e06ea..e81ead1 100644
--- a/arch/arm/mach-omap1/board-htcherald.c
+++ b/arch/arm/mach-omap1/board-htcherald.c
@@ -611,7 +611,7 @@
 MACHINE_START(HERALD, "HTC Herald")
 	/* Maintainer: Cory Maccarrone <darkstar6262@gmail.com> */
 	/* Maintainer: wing-linux.sourceforge.net */
-	.boot_params    = 0x10000100,
+	.atag_offset    = 0x100,
 	.map_io         = htcherald_map_io,
 	.reserve	= omap_reserve,
 	.init_irq       = htcherald_init_irq,
diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c
index 0b1ba46..8b03459 100644
--- a/arch/arm/mach-omap1/board-innovator.c
+++ b/arch/arm/mach-omap1/board-innovator.c
@@ -459,7 +459,7 @@
 
 MACHINE_START(OMAP_INNOVATOR, "TI-Innovator")
 	/* Maintainer: MontaVista Software, Inc. */
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= innovator_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= innovator_init_irq,
diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c
index 5469ce2..6825635 100644
--- a/arch/arm/mach-omap1/board-nokia770.c
+++ b/arch/arm/mach-omap1/board-nokia770.c
@@ -264,7 +264,7 @@
 }
 
 MACHINE_START(NOKIA770, "Nokia 770")
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= omap_nokia770_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= omap_nokia770_init_irq,
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index b08a213..44b8e93 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -583,7 +583,7 @@
 
 MACHINE_START(OMAP_OSK, "TI-OSK")
 	/* Maintainer: Dirk Behme <dirk.behme@de.bosch.com> */
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= osk_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= osk_init_irq,
diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c
index 459cb6b..3d8cd90 100644
--- a/arch/arm/mach-omap1/board-palmte.c
+++ b/arch/arm/mach-omap1/board-palmte.c
@@ -275,7 +275,7 @@
 }
 
 MACHINE_START(OMAP_PALMTE, "OMAP310 based Palm Tungsten E")
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= omap_palmte_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= omap_palmte_init_irq,
diff --git a/arch/arm/mach-omap1/board-palmtt.c b/arch/arm/mach-omap1/board-palmtt.c
index b214f45..d0eefe8 100644
--- a/arch/arm/mach-omap1/board-palmtt.c
+++ b/arch/arm/mach-omap1/board-palmtt.c
@@ -321,7 +321,7 @@
 }
 
 MACHINE_START(OMAP_PALMTT, "OMAP1510 based Palm Tungsten|T")
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= omap_palmtt_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= omap_palmtt_init_irq,
diff --git a/arch/arm/mach-omap1/board-palmz71.c b/arch/arm/mach-omap1/board-palmz71.c
index 9b0ea48..98e79bc 100644
--- a/arch/arm/mach-omap1/board-palmz71.c
+++ b/arch/arm/mach-omap1/board-palmz71.c
@@ -341,7 +341,7 @@
 }
 
 MACHINE_START(OMAP_PALMZ71, "OMAP310 based Palm Zire71")
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= omap_palmz71_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= omap_palmz71_init_irq,
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index 67acd41..ad3a156 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -350,7 +350,7 @@
 
 MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")
 	/* Maintainer: Kevin Hilman <kjh@hilman.org> */
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= omap_perseus2_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= omap_perseus2_init_irq,
diff --git a/arch/arm/mach-omap1/board-sx1.c b/arch/arm/mach-omap1/board-sx1.c
index 9c3b7c5..602b55c 100644
--- a/arch/arm/mach-omap1/board-sx1.c
+++ b/arch/arm/mach-omap1/board-sx1.c
@@ -421,7 +421,7 @@
 }
 
 MACHINE_START(SX1, "OMAP310 based Siemens SX1")
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= omap_sx1_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= omap_sx1_init_irq,
diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c
index 036edc0e..8016515 100644
--- a/arch/arm/mach-omap1/board-voiceblue.c
+++ b/arch/arm/mach-omap1/board-voiceblue.c
@@ -301,7 +301,7 @@
 
 MACHINE_START(VOICEBLUE, "VoiceBlue OMAP5910")
 	/* Maintainer: Ladislav Michl <michl@2n.cz> */
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.map_io		= voiceblue_map_io,
 	.reserve	= omap_reserve,
 	.init_irq	= voiceblue_init_irq,
diff --git a/arch/arm/mach-omap1/include/mach/debug-macro.S b/arch/arm/mach-omap1/include/mach/debug-macro.S
index 6285604..2b36a28 100644
--- a/arch/arm/mach-omap1/include/mach/debug-macro.S
+++ b/arch/arm/mach-omap1/include/mach/debug-macro.S
@@ -13,13 +13,8 @@
 
 #include <linux/serial_reg.h>
 
-#include <asm/memory.h>
-
 #include <plat/serial.h>
 
-#define omap_uart_v2p(x)	((x) - PAGE_OFFSET + PLAT_PHYS_OFFSET)
-#define omap_uart_p2v(x)	((x) - PLAT_PHYS_OFFSET + PAGE_OFFSET)
-
 		.pushsection .data
 omap_uart_phys:	.word	0x0
 omap_uart_virt:	.word	0x0
@@ -31,26 +26,24 @@
 		 * the desired UART phys and virt addresses temporarily into
 		 * the omap_uart_phys and omap_uart_virt above.
 		 */
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 
 		/* Use omap_uart_phys/virt if already configured */
-9:		mrc	p15, 0, \rp, c1, c0
-		tst	\rp, #1			@ MMU enabled?
-		ldreq	\rp, =omap_uart_v2p(omap_uart_phys)	@ MMU disabled
-		ldrne	\rp, =omap_uart_phys	@ MMU enabled
-		add	\rv, \rp, #4		@ omap_uart_virt
-		ldr	\rp, [\rp, #0]
-		ldr	\rv, [\rv, #0]
+9:		adr	\rp, 99f		@ get effective addr of 99f
+		ldr	\rv, [\rp]		@ get absolute addr of 99f
+		sub	\rv, \rv, \rp		@ offset between the two
+		ldr	\rp, [\rp, #4]		@ abs addr of omap_uart_phys
+		sub	\tmp, \rp, \rv		@ make it effective
+		ldr	\rp, [\tmp, #0]		@ omap_uart_phys
+		ldr	\rv, [\tmp, #4]		@ omap_uart_virt
 		cmp	\rp, #0			@ is port configured?
 		cmpne	\rv, #0
-		bne	99f			@ already configured
+		bne	100f			@ already configured
 
 		/* Check the debug UART configuration set in uncompress.h */
-		mrc	p15, 0, \rp, c1, c0
-		tst	\rp, #1			@ MMU enabled?
-		ldreq	\rp, =OMAP_UART_INFO	@ MMU not enabled
-		ldrne	\rp, =omap_uart_p2v(OMAP_UART_INFO)	@ MMU enabled
-		ldr	\rp, [\rp, #0]
+		and	\rp, pc, #0xff000000
+		ldr	\rv, =OMAP_UART_INFO_OFS
+		ldr	\rp, [\rp, \rv]
 
 		/* Select the UART to use based on the UART1 scratchpad value */
 10:		cmp	\rp, #0			@ no port configured?
@@ -74,17 +67,18 @@
 
 		/* Store both phys and virt address for the uart */
 98:		add	\rp, \rp, #0xff000000	@ phys base
-		mrc	p15, 0, \rv, c1, c0
-		tst	\rv, #1			@ MMU enabled?
-		ldreq	\rv, =omap_uart_v2p(omap_uart_phys)	@ MMU disabled
-		ldrne	\rv, =omap_uart_phys	@ MMU enabled
-		str	\rp, [\rv, #0]
+		str	\rp, [\tmp, #0]		@ omap_uart_phys
 		sub	\rp, \rp, #0xff000000	@ phys base
 		add	\rp, \rp, #0xfe000000	@ virt base
-		add	\rv, \rv, #4		@ omap_uart_lsr
-		str	\rp, [\rv, #0]
+		str	\rp, [\tmp, #4]		@ omap_uart_virt
 		b	9b
-99:
+
+		.align
+99:		.word	.
+		.word	omap_uart_phys
+		.ltorg
+
+100:
 		.endm
 
 		.macro	senduart,rd,rx
diff --git a/arch/arm/mach-omap1/include/mach/memory.h b/arch/arm/mach-omap1/include/mach/memory.h
index e9b600c..c633764 100644
--- a/arch/arm/mach-omap1/include/mach/memory.h
+++ b/arch/arm/mach-omap1/include/mach/memory.h
@@ -2,4 +2,55 @@
  * arch/arm/mach-omap1/include/mach/memory.h
  */
 
-#include <plat/memory.h>
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+/*
+ * Physical DRAM offset.
+ */
+#define PLAT_PHYS_OFFSET		UL(0x10000000)
+
+/*
+ * Bus address is physical address, except for OMAP-1510 Local Bus.
+ * OMAP-1510 bus address is translated into a Local Bus address if the
+ * OMAP bus type is lbus. We do the address translation based on the
+ * device overriding the defaults used in the dma-mapping API.
+ * Note that the is_lbus_device() test is not very efficient on 1510
+ * because of the strncmp().
+ */
+#ifdef CONFIG_ARCH_OMAP15XX
+
+/*
+ * OMAP-1510 Local Bus address offset
+ */
+#define OMAP1510_LB_OFFSET	UL(0x30000000)
+
+#define virt_to_lbus(x)		((x) - PAGE_OFFSET + OMAP1510_LB_OFFSET)
+#define lbus_to_virt(x)		((x) - OMAP1510_LB_OFFSET + PAGE_OFFSET)
+#define is_lbus_device(dev)	(cpu_is_omap15xx() && dev && (strncmp(dev_name(dev), "ohci", 4) == 0))
+
+#define __arch_pfn_to_dma(dev, pfn)	\
+	({ dma_addr_t __dma = __pfn_to_phys(pfn); \
+	   if (is_lbus_device(dev)) \
+		__dma = __dma - PHYS_OFFSET + OMAP1510_LB_OFFSET; \
+	   __dma; })
+
+#define __arch_dma_to_pfn(dev, addr)	\
+	({ dma_addr_t __dma = addr;				\
+	   if (is_lbus_device(dev))				\
+		__dma += PHYS_OFFSET - OMAP1510_LB_OFFSET;	\
+	   __phys_to_pfn(__dma);				\
+	})
+
+#define __arch_dma_to_virt(dev, addr)	({ (void *) (is_lbus_device(dev) ? \
+						lbus_to_virt(addr) : \
+						__phys_to_virt(addr)); })
+
+#define __arch_virt_to_dma(dev, addr)	({ unsigned long __addr = (unsigned long)(addr); \
+					   (dma_addr_t) (is_lbus_device(dev) ? \
+						virt_to_lbus(__addr) : \
+						__virt_to_phys(__addr)); })
+
+#endif	/* CONFIG_ARCH_OMAP15XX */
+
+#endif
diff --git a/arch/arm/mach-omap1/io.c b/arch/arm/mach-omap1/io.c
index 870886a..1cfa1b6 100644
--- a/arch/arm/mach-omap1/io.c
+++ b/arch/arm/mach-omap1/io.c
@@ -121,6 +121,7 @@
 #endif
 
 	omap_sram_init();
+	omap_init_consistent_dma_size();
 }
 
 /*
diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c
index 2028464..195157d 100644
--- a/arch/arm/mach-omap2/board-2430sdp.c
+++ b/arch/arm/mach-omap2/board-2430sdp.c
@@ -256,7 +256,7 @@
 
 MACHINE_START(OMAP_2430SDP, "OMAP2430 sdp2430 board")
 	/* Maintainer: Syed Khasim - Texas Instruments Inc */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap_2430sdp_map_io,
 	.init_early	= omap_2430sdp_init_early,
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index bd600cf..2430531 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -729,7 +729,7 @@
 
 MACHINE_START(OMAP_3430SDP, "OMAP3430 3430SDP board")
 	/* Maintainer: Syed Khasim - Texas Instruments Inc */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= omap_3430sdp_init_early,
diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c
index e4f37b5..8b5b5aa 100644
--- a/arch/arm/mach-omap2/board-3630sdp.c
+++ b/arch/arm/mach-omap2/board-3630sdp.c
@@ -215,7 +215,7 @@
 }
 
 MACHINE_START(OMAP_3630SDP, "OMAP 3630SDP board")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= omap_sdp_init_early,
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index c7cef44..be93110 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -838,7 +838,7 @@
 
 MACHINE_START(OMAP_4430SDP, "OMAP4430 4430SDP board")
 	/* Maintainer: Santosh Shilimkar - Texas Instruments Inc */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap_4430sdp_map_io,
 	.init_early	= omap_4430sdp_init_early,
diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 933e935..db110fd 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -98,7 +98,7 @@
 }
 
 MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= am3517_crane_init_early,
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index f3006c3..1325085 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -490,7 +490,7 @@
 }
 
 MACHINE_START(OMAP3517EVM, "OMAP3517/AM3517 EVM")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= am3517_evm_init_early,
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index 7021170..67800e6 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -350,7 +350,7 @@
 
 MACHINE_START(OMAP_APOLLON, "OMAP24xx Apollon")
 	/* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap_apollon_map_io,
 	.init_early	= omap_apollon_init_early,
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index 3af8aab..38179c1 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -634,7 +634,7 @@
 }
 
 MACHINE_START(CM_T35, "Compulab CM-T35")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= cm_t35_init_early,
@@ -644,7 +644,7 @@
 MACHINE_END
 
 MACHINE_START(CM_T3730, "Compulab CM-T3730")
-	.boot_params    = 0x80000100,
+	.atag_offset    = 0x100,
 	.reserve        = omap_reserve,
 	.map_io         = omap3_map_io,
 	.init_early     = cm_t35_init_early,
diff --git a/arch/arm/mach-omap2/board-cm-t3517.c b/arch/arm/mach-omap2/board-cm-t3517.c
index 05c72f4..aed9c29 100644
--- a/arch/arm/mach-omap2/board-cm-t3517.c
+++ b/arch/arm/mach-omap2/board-cm-t3517.c
@@ -299,7 +299,7 @@
 }
 
 MACHINE_START(CM_T3517, "Compulab CM-T3517")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve        = omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= cm_t3517_init_early,
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index b6002ec..99a4243 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -667,7 +667,7 @@
 }
 
 MACHINE_START(DEVKIT8000, "OMAP3 Devkit8000")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= devkit8000_init_early,
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 54db41a..2564269 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -66,7 +66,7 @@
 /* XXX This machine entry name should be updated */
 MACHINE_START(OMAP_GENERIC, "Generic OMAP24xx")
 	/* Maintainer: Paul Mundt <paul.mundt@nokia.com> */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap_generic_map_io,
 	.init_early	= omap_generic_init_early,
diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c
index 45de2b3..a58c6ba 100644
--- a/arch/arm/mach-omap2/board-h4.c
+++ b/arch/arm/mach-omap2/board-h4.c
@@ -382,7 +382,7 @@
 
 MACHINE_START(OMAP_H4, "OMAP2420 H4 board")
 	/* Maintainer: Paul Mundt <paul.mundt@nokia.com> */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap_h4_map_io,
 	.init_early	= omap_h4_init_early,
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 35be778..7040352 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -672,7 +672,7 @@
 }
 
 MACHINE_START(IGEP0020, "IGEP v2 board")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= igep_init_early,
@@ -682,7 +682,7 @@
 MACHINE_END
 
 MACHINE_START(IGEP0030, "IGEP OMAP3 module")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= igep_init_early,
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
index 218764c..edf752b 100644
--- a/arch/arm/mach-omap2/board-ldp.c
+++ b/arch/arm/mach-omap2/board-ldp.c
@@ -333,7 +333,7 @@
 }
 
 MACHINE_START(OMAP_LDP, "OMAP LDP board")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= omap_ldp_init_early,
diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index e11f0c5..6ce7481 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -695,7 +695,7 @@
 }
 
 MACHINE_START(NOKIA_N800, "Nokia N800")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= n8x0_map_io,
 	.init_early	= n8x0_init_early,
@@ -705,7 +705,7 @@
 MACHINE_END
 
 MACHINE_START(NOKIA_N810, "Nokia N810")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= n8x0_map_io,
 	.init_early	= n8x0_init_early,
@@ -715,7 +715,7 @@
 MACHINE_END
 
 MACHINE_START(NOKIA_N810_WIMAX, "Nokia N810 WiMAX")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= n8x0_map_io,
 	.init_early	= n8x0_init_early,
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 3ae16b4..1fde8a0 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -557,7 +557,7 @@
 
 MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
 	/* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= omap3_beagle_init_early,
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index c452b3f..15c69a0 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -681,7 +681,7 @@
 
 MACHINE_START(OMAP3EVM, "OMAP3 EVM")
 	/* Maintainer: Syed Mohammed Khasim - Texas Instruments */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= omap3_evm_init_early,
diff --git a/arch/arm/mach-omap2/board-omap3logic.c b/arch/arm/mach-omap2/board-omap3logic.c
index 703aeb5..01354a2 100644
--- a/arch/arm/mach-omap2/board-omap3logic.c
+++ b/arch/arm/mach-omap2/board-omap3logic.c
@@ -209,7 +209,7 @@
 }
 
 MACHINE_START(OMAP3_TORPEDO, "Logic OMAP3 Torpedo board")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.map_io		= omap3_map_io,
 	.init_early	= omap3logic_init_early,
 	.init_irq	= omap3_init_irq,
@@ -218,7 +218,7 @@
 MACHINE_END
 
 MACHINE_START(OMAP3530_LV_SOM, "OMAP Logic 3530 LV SOM board")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.map_io		= omap3_map_io,
 	.init_early	= omap3logic_init_early,
 	.init_irq	= omap3_init_irq,
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 080d7bd..ace56938 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -606,7 +606,7 @@
 }
 
 MACHINE_START(OMAP3_PANDORA, "Pandora Handheld Console")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= omap3pandora_init_early,
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c
index 8e10498..ba13e1d 100644
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ b/arch/arm/mach-omap2/board-omap3stalker.c
@@ -494,7 +494,7 @@
 
 MACHINE_START(SBC3530, "OMAP3 STALKER")
 	/* Maintainer: Jason Lam -lzg@ema-tech.com */
-	.boot_params		= 0x80000100,
+	.atag_offset		= 0x100,
 	.map_io			= omap3_map_io,
 	.init_early		= omap3_stalker_init_early,
 	.init_irq		= omap3_stalker_init_irq,
diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c
index 852ea04..49e4bd2 100644
--- a/arch/arm/mach-omap2/board-omap3touchbook.c
+++ b/arch/arm/mach-omap2/board-omap3touchbook.c
@@ -404,7 +404,7 @@
 
 MACHINE_START(TOUCHBOOK, "OMAP3 touchbook Board")
 	/* Maintainer: Gregoire Gentil - http://www.alwaysinnovating.com */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= omap3_touchbook_init_early,
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 9aaa960..683bede 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -583,7 +583,7 @@
 
 MACHINE_START(OMAP4_PANDA, "OMAP4 Panda board")
 	/* Maintainer: David Anders - Texas Instruments Inc */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap4_panda_map_io,
 	.init_early	= omap4_panda_init_early,
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index f949a99..e592fb1 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -561,7 +561,7 @@
 }
 
 MACHINE_START(OVERO, "Gumstix Overo")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= overo_init_early,
diff --git a/arch/arm/mach-omap2/board-rm680.c b/arch/arm/mach-omap2/board-rm680.c
index 7dfed24..9a8ce23 100644
--- a/arch/arm/mach-omap2/board-rm680.c
+++ b/arch/arm/mach-omap2/board-rm680.c
@@ -153,7 +153,7 @@
 }
 
 MACHINE_START(NOKIA_RM680, "Nokia RM-680 board")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= rm680_map_io,
 	.init_early	= rm680_init_early,
diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c
index 5ea142f..a6c473b 100644
--- a/arch/arm/mach-omap2/board-rx51.c
+++ b/arch/arm/mach-omap2/board-rx51.c
@@ -156,7 +156,7 @@
 
 MACHINE_START(NOKIA_RX51, "Nokia RX-51 board")
 	/* Maintainer: Lauri Leukkunen <lauri.leukkunen@nokia.com> */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= rx51_reserve,
 	.map_io		= rx51_map_io,
 	.init_early	= rx51_init_early,
diff --git a/arch/arm/mach-omap2/board-ti8168evm.c b/arch/arm/mach-omap2/board-ti8168evm.c
index a85d5b0..e41958a 100644
--- a/arch/arm/mach-omap2/board-ti8168evm.c
+++ b/arch/arm/mach-omap2/board-ti8168evm.c
@@ -48,7 +48,7 @@
 
 MACHINE_START(TI8168EVM, "ti8168evm")
 	/* Maintainer: Texas Instruments */
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.map_io		= ti8168_evm_map_io,
 	.init_early	= ti8168_init_early,
 	.init_irq	= ti816x_init_irq,
diff --git a/arch/arm/mach-omap2/board-zoom.c b/arch/arm/mach-omap2/board-zoom.c
index 8a98c3c..72f1db4 100644
--- a/arch/arm/mach-omap2/board-zoom.c
+++ b/arch/arm/mach-omap2/board-zoom.c
@@ -133,7 +133,7 @@
 }
 
 MACHINE_START(OMAP_ZOOM2, "OMAP Zoom2 board")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= omap_zoom_init_early,
@@ -143,7 +143,7 @@
 MACHINE_END
 
 MACHINE_START(OMAP_ZOOM3, "OMAP Zoom3 board")
-	.boot_params	= 0x80000100,
+	.atag_offset	= 0x100,
 	.reserve	= omap_reserve,
 	.map_io		= omap3_map_io,
 	.init_early	= omap_zoom_init_early,
diff --git a/arch/arm/mach-omap2/include/mach/debug-macro.S b/arch/arm/mach-omap2/include/mach/debug-macro.S
index 48adfe9..13f98e5 100644
--- a/arch/arm/mach-omap2/include/mach/debug-macro.S
+++ b/arch/arm/mach-omap2/include/mach/debug-macro.S
@@ -13,15 +13,10 @@
 
 #include <linux/serial_reg.h>
 
-#include <asm/memory.h>
-
 #include <plat/serial.h>
 
 #define UART_OFFSET(addr)	((addr) & 0x00ffffff)
 
-#define omap_uart_v2p(x)	((x) - PAGE_OFFSET + PLAT_PHYS_OFFSET)
-#define omap_uart_p2v(x)	((x) - PLAT_PHYS_OFFSET + PAGE_OFFSET)
-
 		.pushsection .data
 omap_uart_phys:	.word	0
 omap_uart_virt:	.word	0
@@ -34,26 +29,25 @@
 		 * the desired UART phys and virt addresses temporarily into
 		 * the omap_uart_phys and omap_uart_virt above.
 		 */
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 
 		/* Use omap_uart_phys/virt if already configured */
-10:		mrc	p15, 0, \rp, c1, c0
-		tst	\rp, #1			@ MMU enabled?
-		ldreq	\rp, =omap_uart_v2p(omap_uart_phys)	@ MMU disabled
-		ldrne	\rp, =omap_uart_phys	@ MMU enabled
-		add	\rv, \rp, #4		@ omap_uart_virt
-		ldr	\rp, [\rp, #0]
-		ldr	\rv, [\rv, #0]
+10:		adr	\rp, 99f		@ get effective addr of 99f
+		ldr	\rv, [\rp]		@ get absolute addr of 99f
+		sub	\rv, \rv, \rp		@ offset between the two
+		ldr	\rp, [\rp, #4]		@ abs addr of omap_uart_phys
+		sub	\tmp, \rp, \rv		@ make it effective
+		ldr	\rp, [\tmp, #0]		@ omap_uart_phys
+		ldr	\rv, [\tmp, #4]		@ omap_uart_virt
 		cmp	\rp, #0			@ is port configured?
 		cmpne	\rv, #0
-		bne	99f			@ already configured
+		bne	100f			@ already configured
 
 		/* Check the debug UART configuration set in uncompress.h */
-		mrc	p15, 0, \rp, c1, c0
-		tst	\rp, #1			@ MMU enabled?
-		ldreq	\rp, =OMAP_UART_INFO	@ MMU not enabled
-		ldrne	\rp, =omap_uart_p2v(OMAP_UART_INFO)	@ MMU enabled
-		ldr	\rp, [\rp, #0]
+		mov	\rp, pc
+		ldr	\rv, =OMAP_UART_INFO_OFS
+		and	\rp, \rp, #0xff000000
+		ldr	\rp, [\rp, \rv]
 
 		/* Select the UART to use based on the UART1 scratchpad value */
 		cmp	\rp, #0			@ no port configured?
@@ -106,50 +100,47 @@
 		b	98f
 83:		mov	\rp, #UART_OFFSET(TI816X_UART3_BASE)
 		b	98f
+
 95:		ldr	\rp, =ZOOM_UART_BASE
-		mrc	p15, 0, \rv, c1, c0
-		tst	\rv, #1			@ MMU enabled?
-		ldreq	\rv, =omap_uart_v2p(omap_uart_phys)	@ MMU disabled
-		ldrne	\rv, =omap_uart_phys	@ MMU enabled
-		str	\rp, [\rv, #0]
+		str	\rp, [\tmp, #0]		@ omap_uart_phys
 		ldr	\rp, =ZOOM_UART_VIRT
-		add	\rv, \rv, #4		@ omap_uart_virt
-		str	\rp, [\rv, #0]
+		str	\rp, [\tmp, #4]		@ omap_uart_virt
 		mov	\rp, #(UART_LSR << ZOOM_PORT_SHIFT)
-		add	\rv, \rv, #4		@ omap_uart_lsr
-		str	\rp, [\rv, #0]
+		str	\rp, [\tmp, #8]		@ omap_uart_lsr
 		b	10b
 
 		/* Store both phys and virt address for the uart */
 98:		add	\rp, \rp, #0x48000000	@ phys base
-		mrc	p15, 0, \rv, c1, c0
-		tst	\rv, #1			@ MMU enabled?
-		ldreq	\rv, =omap_uart_v2p(omap_uart_phys)	@ MMU disabled
-		ldrne	\rv, =omap_uart_phys	@ MMU enabled
-		str	\rp, [\rv, #0]
+		str	\rp, [\tmp, #0]		@ omap_uart_phys
 		sub	\rp, \rp, #0x48000000	@ phys base
 		add	\rp, \rp, #0xfa000000	@ virt base
-		add	\rv, \rv, #4		@ omap_uart_virt
-		str	\rp, [\rv, #0]
+		str	\rp, [\tmp, #4]		@ omap_uart_virt
 		mov	\rp, #(UART_LSR << OMAP_PORT_SHIFT)
-		add	\rv, \rv, #4		@ omap_uart_lsr
-		str	\rp, [\rv, #0]
+		str	\rp, [\tmp, #8]		@ omap_uart_lsr
 
 		b	10b
-99:
+
+		.align
+99:		.word	.
+		.word	omap_uart_phys
+		.ltorg
+
+100:		/* Pass the UART_LSR reg address */
+		ldr	\tmp, [\tmp, #8]	@ omap_uart_lsr
+		add	\rp, \rp, \tmp
+		add	\rv, \rv, \tmp
 		.endm
 
 		.macro	senduart,rd,rx
-		strb	\rd, [\rx]
+		orr	\rd, \rd, \rx, lsl #24	@ preserve LSR reg offset
+		bic	\rx, \rx, #0xff		@ get base (THR) reg address
+		strb	\rd, [\rx]		@ send lower byte of rd
+		orr	\rx, \rx, \rd, lsr #24	@ restore original rx (LSR)
+		bic	\rd, \rd, #(0xff << 24)	@ restore original rd
 		.endm
 
 		.macro	busyuart,rd,rx
-1001:		mrc	p15, 0, \rd, c1, c0
-		tst	\rd, #1			@ MMU enabled?
-		ldreq	\rd, =omap_uart_v2p(omap_uart_lsr)	@ MMU disabled
-		ldrne	\rd, =omap_uart_lsr	@ MMU enabled
-		ldr	\rd, [\rd, #0]
-		ldrb	\rd, [\rx, \rd]
+1001:		ldrb	\rd, [\rx]		@ rx contains UART_LSR address
 		and	\rd, \rd, #(UART_LSR_TEMT | UART_LSR_THRE)
 		teq	\rd, #(UART_LSR_TEMT | UART_LSR_THRE)
 		bne	1001b
diff --git a/arch/arm/mach-omap2/include/mach/entry-macro.S b/arch/arm/mach-omap2/include/mach/entry-macro.S
index ceb8b7e..feb90a1 100644
--- a/arch/arm/mach-omap2/include/mach/entry-macro.S
+++ b/arch/arm/mach-omap2/include/mach/entry-macro.S
@@ -78,7 +78,7 @@
 4401:		ldr     \irqstat, [\base, #GIC_CPU_INTACK]
 		ldr     \tmp, =1021
 		bic     \irqnr, \irqstat, #0x1c00
-		cmp     \irqnr, #29
+		cmp     \irqnr, #15
 		cmpcc   \irqnr, \irqnr
 		cmpne   \irqnr, \tmp
 		cmpcs   \irqnr, \irqnr
@@ -101,18 +101,6 @@
 		it	cs
 		cmpcs	\irqnr, \irqnr
 		.endm
-
-		/* As above, this assumes that irqstat and base are preserved */
-
-		.macro test_for_ltirq, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		mov 	\tmp, #0
-		cmp	\irqnr, #29
-		itt	eq
-		moveq	\tmp, #1
-		streq	\irqstat, [\base, #GIC_CPU_EOI]
-		cmp	\tmp, #0
-		.endm
 #endif	/* CONFIG_SMP */
 
 #else	/* MULTI_OMAP2 */
diff --git a/arch/arm/mach-omap2/include/mach/memory.h b/arch/arm/mach-omap2/include/mach/memory.h
deleted file mode 100644
index ca6d32a..0000000
--- a/arch/arm/mach-omap2/include/mach/memory.h
+++ /dev/null
@@ -1,5 +0,0 @@
-/*
- * arch/arm/mach-omap2/include/mach/memory.h
- */
-
-#include <plat/memory.h>
diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index 2ce1ce6..d6d01cb 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -16,7 +16,6 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -250,6 +249,7 @@
 
 	omap2_check_revision();
 	omap_sram_init();
+	omap_init_consistent_dma_size();
 }
 
 #ifdef CONFIG_SOC_OMAP2420
diff --git a/arch/arm/mach-omap2/omap-smp.c b/arch/arm/mach-omap2/omap-smp.c
index ce65e93..889464d 100644
--- a/arch/arm/mach-omap2/omap-smp.c
+++ b/arch/arm/mach-omap2/omap-smp.c
@@ -109,12 +109,10 @@
 	ncores = scu_get_core_count(scu_base);
 
 	/* sanity check */
-	if (ncores > NR_CPUS) {
-		printk(KERN_WARNING
-		       "OMAP4: no. of cores (%d) greater than configured "
-		       "maximum of %d - clipping\n",
-		       ncores, NR_CPUS);
-		ncores = NR_CPUS;
+	if (ncores > nr_cpu_ids) {
+		pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+			ncores, nr_cpu_ids);
+		ncores = nr_cpu_ids;
 	}
 
 	for (i = 0; i < ncores; i++)
diff --git a/arch/arm/mach-orion5x/d2net-setup.c b/arch/arm/mach-orion5x/d2net-setup.c
index 19cf5bf..8c83009 100644
--- a/arch/arm/mach-orion5x/d2net-setup.c
+++ b/arch/arm/mach-orion5x/d2net-setup.c
@@ -336,7 +336,7 @@
 
 #ifdef CONFIG_MACH_D2NET
 MACHINE_START(D2NET, "LaCie d2 Network")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= d2net_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
@@ -348,7 +348,7 @@
 
 #ifdef CONFIG_MACH_BIGDISK
 MACHINE_START(BIGDISK, "LaCie Big Disk Network")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= d2net_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/db88f5281-setup.c b/arch/arm/mach-orion5x/db88f5281-setup.c
index a3e3e9e..88432ab 100644
--- a/arch/arm/mach-orion5x/db88f5281-setup.c
+++ b/arch/arm/mach-orion5x/db88f5281-setup.c
@@ -359,7 +359,7 @@
 
 MACHINE_START(DB88F5281, "Marvell Orion-2 Development Board")
 	/* Maintainer: Tzachi Perelstein <tzachi@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= db88f5281_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/dns323-setup.c b/arch/arm/mach-orion5x/dns323-setup.c
index c105556..9e5c166 100644
--- a/arch/arm/mach-orion5x/dns323-setup.c
+++ b/arch/arm/mach-orion5x/dns323-setup.c
@@ -730,7 +730,7 @@
 /* Warning: D-Link uses a wrong mach-type (=526) in their bootloader */
 MACHINE_START(DNS323, "D-Link DNS-323")
 	/* Maintainer: Herbert Valerio Riedel <hvr@gnu.org> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= dns323_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/edmini_v2-setup.c b/arch/arm/mach-orion5x/edmini_v2-setup.c
index b67cff0..70a4e92 100644
--- a/arch/arm/mach-orion5x/edmini_v2-setup.c
+++ b/arch/arm/mach-orion5x/edmini_v2-setup.c
@@ -251,7 +251,7 @@
 /* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
 MACHINE_START(EDMINI_V2, "LaCie Ethernet Disk mini V2")
 	/* Maintainer: Christopher Moore <moore@free.fr> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= edmini_v2_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/include/mach/debug-macro.S b/arch/arm/mach-orion5x/include/mach/debug-macro.S
index 5e3bf5b..f340ed8 100644
--- a/arch/arm/mach-orion5x/include/mach/debug-macro.S
+++ b/arch/arm/mach-orion5x/include/mach/debug-macro.S
@@ -10,7 +10,7 @@
 
 #include <mach/orion5x.h>
 
-	.macro  addruart, rp, rv
+	.macro  addruart, rp, rv, tmp
 	ldr	\rp, =ORION5X_REGS_PHYS_BASE
 	ldr	\rv, =ORION5X_REGS_VIRT_BASE
 	orr	\rp, \rp, #0x00012000
diff --git a/arch/arm/mach-orion5x/include/mach/memory.h b/arch/arm/mach-orion5x/include/mach/memory.h
deleted file mode 100644
index 6769917..0000000
--- a/arch/arm/mach-orion5x/include/mach/memory.h
+++ /dev/null
@@ -1,12 +0,0 @@
-/*
- * arch/arm/mach-orion5x/include/mach/memory.h
- *
- * Marvell Orion memory definitions
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET	UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-orion5x/kurobox_pro-setup.c b/arch/arm/mach-orion5x/kurobox_pro-setup.c
index 0038124..9115511 100644
--- a/arch/arm/mach-orion5x/kurobox_pro-setup.c
+++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c
@@ -380,7 +380,7 @@
 #ifdef CONFIG_MACH_KUROBOX_PRO
 MACHINE_START(KUROBOX_PRO, "Buffalo/Revogear Kurobox Pro")
 	/* Maintainer: Ronen Shitrit <rshitrit@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= kurobox_pro_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
@@ -393,7 +393,7 @@
 #ifdef CONFIG_MACH_LINKSTATION_PRO
 MACHINE_START(LINKSTATION_PRO, "Buffalo Linkstation Pro/Live")
 	/* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= kurobox_pro_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/ls-chl-setup.c b/arch/arm/mach-orion5x/ls-chl-setup.c
index 5065803..9503fff 100644
--- a/arch/arm/mach-orion5x/ls-chl-setup.c
+++ b/arch/arm/mach-orion5x/ls-chl-setup.c
@@ -318,7 +318,7 @@
 
 MACHINE_START(LINKSTATION_LSCHL, "Buffalo Linkstation LiveV3 (LS-CHL)")
 	/* Maintainer: Ash Hughes <ashley.hughes@blueyonder.co.uk> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= lschl_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/ls_hgl-setup.c b/arch/arm/mach-orion5x/ls_hgl-setup.c
index 8503d0a..ed6d772 100644
--- a/arch/arm/mach-orion5x/ls_hgl-setup.c
+++ b/arch/arm/mach-orion5x/ls_hgl-setup.c
@@ -265,7 +265,7 @@
 
 MACHINE_START(LINKSTATION_LS_HGL, "Buffalo Linkstation LS-HGL")
 	/* Maintainer: Zhu Qingsen <zhuqs@cn.fujistu.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= ls_hgl_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/lsmini-setup.c b/arch/arm/mach-orion5x/lsmini-setup.c
index 9c82723..743f7f1 100644
--- a/arch/arm/mach-orion5x/lsmini-setup.c
+++ b/arch/arm/mach-orion5x/lsmini-setup.c
@@ -267,7 +267,7 @@
 #ifdef CONFIG_MACH_LINKSTATION_MINI
 MACHINE_START(LINKSTATION_MINI, "Buffalo Linkstation Mini")
 	/* Maintainer: Alexey Kopytko <alexey@kopytko.ru> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= lsmini_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/mss2-setup.c b/arch/arm/mach-orion5x/mss2-setup.c
index ef3bb8e..6020e26b 100644
--- a/arch/arm/mach-orion5x/mss2-setup.c
+++ b/arch/arm/mach-orion5x/mss2-setup.c
@@ -261,7 +261,7 @@
 
 MACHINE_START(MSS2, "Maxtor Shared Storage II")
 	/* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= mss2_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/mv2120-setup.c b/arch/arm/mach-orion5x/mv2120-setup.c
index 63ff10c..b3356ad 100644
--- a/arch/arm/mach-orion5x/mv2120-setup.c
+++ b/arch/arm/mach-orion5x/mv2120-setup.c
@@ -229,7 +229,7 @@
 /* Warning: HP uses a wrong mach-type (=526) in their bootloader */
 MACHINE_START(MV2120, "HP Media Vault mv2120")
 	/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= mv2120_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/net2big-setup.c b/arch/arm/mach-orion5x/net2big-setup.c
index e43b39c..6197c79 100644
--- a/arch/arm/mach-orion5x/net2big-setup.c
+++ b/arch/arm/mach-orion5x/net2big-setup.c
@@ -419,7 +419,7 @@
 
 /* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
 MACHINE_START(NET2BIG, "LaCie 2Big Network")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= net2big_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
index 291d22b..8c87666 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
@@ -169,7 +169,7 @@
 
 MACHINE_START(RD88F5181L_FXO, "Marvell Orion-VoIP FXO Reference Design")
 	/* Maintainer: Nicolas Pitre <nico@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= rd88f5181l_fxo_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
index 3f02362..994644f 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
@@ -181,7 +181,7 @@
 
 MACHINE_START(RD88F5181L_GE, "Marvell Orion-VoIP GE Reference Design")
 	/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= rd88f5181l_ge_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/rd88f5182-setup.c b/arch/arm/mach-orion5x/rd88f5182-setup.c
index 27fd38e..1903d25 100644
--- a/arch/arm/mach-orion5x/rd88f5182-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5182-setup.c
@@ -306,7 +306,7 @@
 
 MACHINE_START(RD88F5182, "Marvell Orion-NAS Reference Design")
 	/* Maintainer: Ronen Shitrit <rshitrit@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= rd88f5182_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
index ad2eba9..e06fdae 100644
--- a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
@@ -122,7 +122,7 @@
 
 MACHINE_START(RD88F6183AP_GE, "Marvell Orion-1-90 AP GE Reference Design")
 	/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= rd88f6183ap_ge_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/terastation_pro2-setup.c b/arch/arm/mach-orion5x/terastation_pro2-setup.c
index a34e4fa..3061832 100644
--- a/arch/arm/mach-orion5x/terastation_pro2-setup.c
+++ b/arch/arm/mach-orion5x/terastation_pro2-setup.c
@@ -358,7 +358,7 @@
 
 MACHINE_START(TERASTATION_PRO2, "Buffalo Terastation Pro II/Live")
 	/* Maintainer:  Sylver Bruneau <sylver.bruneau@googlemail.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= tsp2_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/ts209-setup.c b/arch/arm/mach-orion5x/ts209-setup.c
index c983161..3dbcd5e 100644
--- a/arch/arm/mach-orion5x/ts209-setup.c
+++ b/arch/arm/mach-orion5x/ts209-setup.c
@@ -323,7 +323,7 @@
 
 MACHINE_START(TS209, "QNAP TS-109/TS-209")
 	/* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= qnap_ts209_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/ts409-setup.c b/arch/arm/mach-orion5x/ts409-setup.c
index cc33b22..23c9e2e 100644
--- a/arch/arm/mach-orion5x/ts409-setup.c
+++ b/arch/arm/mach-orion5x/ts409-setup.c
@@ -312,7 +312,7 @@
 
 MACHINE_START(TS409, "QNAP TS-409")
 	/* Maintainer:  Sylver Bruneau <sylver.bruneau@gmail.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= qnap_ts409_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/ts78xx-setup.c b/arch/arm/mach-orion5x/ts78xx-setup.c
index 6b7b541..6c75cd3 100644
--- a/arch/arm/mach-orion5x/ts78xx-setup.c
+++ b/arch/arm/mach-orion5x/ts78xx-setup.c
@@ -621,7 +621,7 @@
 
 MACHINE_START(TS78XX, "Technologic Systems TS-78xx SBC")
 	/* Maintainer: Alexander Clouter <alex@digriz.org.uk> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= ts78xx_init,
 	.map_io		= ts78xx_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/wnr854t-setup.c b/arch/arm/mach-orion5x/wnr854t-setup.c
index 2653595..1c63a76 100644
--- a/arch/arm/mach-orion5x/wnr854t-setup.c
+++ b/arch/arm/mach-orion5x/wnr854t-setup.c
@@ -173,7 +173,7 @@
 
 MACHINE_START(WNR854T, "Netgear WNR854T")
 	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= wnr854t_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-orion5x/wrt350n-v2-setup.c b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
index 251ef15..4fd9f18 100644
--- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c
+++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
@@ -261,7 +261,7 @@
 
 MACHINE_START(WRT350N_V2, "Linksys WRT350N v2")
 	/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= wrt350n_v2_init,
 	.map_io		= orion5x_map_io,
 	.init_early	= orion5x_init_early,
diff --git a/arch/arm/mach-pnx4008/core.c b/arch/arm/mach-pnx4008/core.c
index 63399755..cdb95e7 100644
--- a/arch/arm/mach-pnx4008/core.c
+++ b/arch/arm/mach-pnx4008/core.c
@@ -264,7 +264,7 @@
 
 MACHINE_START(PNX4008, "Philips PNX4008")
 	/* Maintainer: MontaVista Software Inc. */
-	.boot_params		= 0x80000100,
+	.atag_offset		= 0x100,
 	.map_io 		= pnx4008_map_io,
 	.init_irq 		= pnx4008_init_irq,
 	.init_machine 		= pnx4008_init,
diff --git a/arch/arm/mach-pnx4008/include/mach/debug-macro.S b/arch/arm/mach-pnx4008/include/mach/debug-macro.S
index 931afeb..469d60d 100644
--- a/arch/arm/mach-pnx4008/include/mach/debug-macro.S
+++ b/arch/arm/mach-pnx4008/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00090000
 		add	\rv, \rp, #0xf4000000	@ virtual
 		add	\rp, \rp, #0x40000000	@ physical
diff --git a/arch/arm/mach-pnx4008/include/mach/memory.h b/arch/arm/mach-pnx4008/include/mach/memory.h
deleted file mode 100644
index 1275db6..0000000
--- a/arch/arm/mach-pnx4008/include/mach/memory.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/memory.h
- *
- * Copyright (c) 2005 Philips Semiconductors
- * Copyright (c) 2005 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET	UL(0x80000000)
-
-#endif
diff --git a/arch/arm/mach-prima2/include/mach/debug-macro.S b/arch/arm/mach-prima2/include/mach/debug-macro.S
index bf75106..cd97492 100644
--- a/arch/arm/mach-prima2/include/mach/debug-macro.S
+++ b/arch/arm/mach-prima2/include/mach/debug-macro.S
@@ -9,7 +9,7 @@
 #include <mach/hardware.h>
 #include <mach/uart.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =SIRFSOC_UART1_PA_BASE		@ physical
 	ldr	\rv, =SIRFSOC_UART1_VA_BASE		@ virtual
 	.endm
diff --git a/arch/arm/mach-prima2/include/mach/memory.h b/arch/arm/mach-prima2/include/mach/memory.h
deleted file mode 100644
index 368cd5a..0000000
--- a/arch/arm/mach-prima2/include/mach/memory.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * arch/arm/mach-prima2/include/mach/memory.h
- *
- * Copyright (c) 2010 – 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
- *
- * Licensed under GPLv2 or later.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET        UL(0x00000000)
-
-/*
- * Restrict DMA-able region to workaround silicon limitation.
- * The limitation restricts buffers available for DMA to SD/MMC
- * hardware to be below 256MB
- */
-#define ARM_DMA_ZONE_SIZE	(SZ_256M)
-
-#endif
diff --git a/arch/arm/mach-prima2/l2x0.c b/arch/arm/mach-prima2/l2x0.c
index 9cda205..66c6387e 100644
--- a/arch/arm/mach-prima2/l2x0.c
+++ b/arch/arm/mach-prima2/l2x0.c
@@ -13,7 +13,6 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <asm/hardware/cache-l2x0.h>
-#include <mach/memory.h>
 
 #define L2X0_ADDR_FILTERING_START       0xC00
 #define L2X0_ADDR_FILTERING_END         0xC04
@@ -41,9 +40,9 @@
 		/*
 		 * set the physical memory windows L2 cache will cover
 		 */
-		writel_relaxed(PLAT_PHYS_OFFSET + 1024 * 1024 * 1024,
+		writel_relaxed(PHYS_OFFSET + 1024 * 1024 * 1024,
 			sirfsoc_l2x_base + L2X0_ADDR_FILTERING_END);
-		writel_relaxed(PLAT_PHYS_OFFSET | 0x1,
+		writel_relaxed(PHYS_OFFSET | 0x1,
 			sirfsoc_l2x_base + L2X0_ADDR_FILTERING_START);
 
 		writel_relaxed(0,
diff --git a/arch/arm/mach-prima2/prima2.c b/arch/arm/mach-prima2/prima2.c
index f57124b..ee33c3d 100644
--- a/arch/arm/mach-prima2/prima2.c
+++ b/arch/arm/mach-prima2/prima2.c
@@ -31,11 +31,12 @@
 
 MACHINE_START(PRIMA2_EVB, "prima2cb")
 	/* Maintainer: Barry Song <baohua.song@csr.com> */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_early     = sirfsoc_of_clk_init,
 	.map_io         = sirfsoc_map_lluart,
 	.init_irq	= sirfsoc_of_irq_init,
 	.timer		= &sirfsoc_timer,
+	.dma_zone_size	= SZ_256M,
 	.init_machine	= sirfsoc_mach_init,
 	.dt_compat      = prima2cb_dt_match,
 MACHINE_END
diff --git a/arch/arm/mach-pxa/balloon3.c b/arch/arm/mach-pxa/balloon3.c
index ef3e8b1..7765d67 100644
--- a/arch/arm/mach-pxa/balloon3.c
+++ b/arch/arm/mach-pxa/balloon3.c
@@ -828,5 +828,5 @@
 	.handle_irq	= pxa27x_handle_irq,
 	.timer		= &pxa_timer,
 	.init_machine	= balloon3_init,
-	.boot_params	= PLAT_PHYS_OFFSET + 0x100,
+	.atag_offset	= 0x100,
 MACHINE_END
diff --git a/arch/arm/mach-pxa/capc7117.c b/arch/arm/mach-pxa/capc7117.c
index 648b0ab..4efc16d 100644
--- a/arch/arm/mach-pxa/capc7117.c
+++ b/arch/arm/mach-pxa/capc7117.c
@@ -148,7 +148,7 @@
 
 MACHINE_START(CAPC7117,
 	      "Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM")
-	.boot_params = 0xa0000100,
+	.atag_offset = 0x100,
 	.map_io = pxa3xx_map_io,
 	.init_irq = pxa3xx_init_irq,
 	.handle_irq = pxa3xx_handle_irq,
diff --git a/arch/arm/mach-pxa/cm-x2xx.c b/arch/arm/mach-pxa/cm-x2xx.c
index 13cf518..349896c 100644
--- a/arch/arm/mach-pxa/cm-x2xx.c
+++ b/arch/arm/mach-pxa/cm-x2xx.c
@@ -513,7 +513,7 @@
 #endif
 
 MACHINE_START(ARMCORE, "Compulab CM-X2XX")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= cmx2xx_map_io,
 	.nr_irqs	= CMX2XX_NR_IRQS,
 	.init_irq	= cmx2xx_init_irq,
diff --git a/arch/arm/mach-pxa/cm-x300.c b/arch/arm/mach-pxa/cm-x300.c
index b6a5134..9ac0225 100644
--- a/arch/arm/mach-pxa/cm-x300.c
+++ b/arch/arm/mach-pxa/cm-x300.c
@@ -852,7 +852,7 @@
 }
 
 MACHINE_START(CM_X300, "CM-X300 module")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa3xx_map_io,
 	.init_irq	= pxa3xx_init_irq,
 	.handle_irq	= pxa3xx_handle_irq,
diff --git a/arch/arm/mach-pxa/colibri-pxa270.c b/arch/arm/mach-pxa/colibri-pxa270.c
index 8709209..7db6646 100644
--- a/arch/arm/mach-pxa/colibri-pxa270.c
+++ b/arch/arm/mach-pxa/colibri-pxa270.c
@@ -306,7 +306,7 @@
 }
 
 MACHINE_START(COLIBRI, "Toradex Colibri PXA270")
-	.boot_params	= COLIBRI_SDRAM_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.init_machine	= colibri_pxa270_init,
 	.map_io		= pxa27x_map_io,
 	.init_irq	= pxa27x_init_irq,
@@ -315,7 +315,7 @@
 MACHINE_END
 
 MACHINE_START(INCOME, "Income s.r.o. SH-Dmaster PXA270 SBC")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.init_machine	= colibri_pxa270_income_init,
 	.map_io		= pxa27x_map_io,
 	.init_irq	= pxa27x_init_irq,
diff --git a/arch/arm/mach-pxa/colibri-pxa300.c b/arch/arm/mach-pxa/colibri-pxa300.c
index 60a6781..c825e8b 100644
--- a/arch/arm/mach-pxa/colibri-pxa300.c
+++ b/arch/arm/mach-pxa/colibri-pxa300.c
@@ -183,7 +183,7 @@
 }
 
 MACHINE_START(COLIBRI300, "Toradex Colibri PXA300")
-	.boot_params	= COLIBRI_SDRAM_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.init_machine	= colibri_pxa300_init,
 	.map_io		= pxa3xx_map_io,
 	.init_irq	= pxa3xx_init_irq,
diff --git a/arch/arm/mach-pxa/colibri-pxa320.c b/arch/arm/mach-pxa/colibri-pxa320.c
index d2c6631..692e1ff 100644
--- a/arch/arm/mach-pxa/colibri-pxa320.c
+++ b/arch/arm/mach-pxa/colibri-pxa320.c
@@ -253,7 +253,7 @@
 }
 
 MACHINE_START(COLIBRI320, "Toradex Colibri PXA320")
-	.boot_params	= COLIBRI_SDRAM_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.init_machine	= colibri_pxa320_init,
 	.map_io		= pxa3xx_map_io,
 	.init_irq	= pxa3xx_init_irq,
diff --git a/arch/arm/mach-pxa/csb726.c b/arch/arm/mach-pxa/csb726.c
index fe812ea..5e2cf39 100644
--- a/arch/arm/mach-pxa/csb726.c
+++ b/arch/arm/mach-pxa/csb726.c
@@ -272,7 +272,7 @@
 }
 
 MACHINE_START(CSB726, "Cogent CSB726")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io         = pxa27x_map_io,
 	.init_irq       = pxa27x_init_irq,
 	.handle_irq       = pxa27x_handle_irq,
diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c
index 2e37ea5..94acc0b 100644
--- a/arch/arm/mach-pxa/em-x270.c
+++ b/arch/arm/mach-pxa/em-x270.c
@@ -1299,7 +1299,7 @@
 }
 
 MACHINE_START(EM_X270, "Compulab EM-X270")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa27x_map_io,
 	.init_irq	= pxa27x_init_irq,
 	.handle_irq	= pxa27x_handle_irq,
@@ -1308,7 +1308,7 @@
 MACHINE_END
 
 MACHINE_START(EXEDA, "Compulab eXeda")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa27x_map_io,
 	.init_irq	= pxa27x_init_irq,
 	.handle_irq	= pxa27x_handle_irq,
diff --git a/arch/arm/mach-pxa/eseries.c b/arch/arm/mach-pxa/eseries.c
index b4599ec..e823c54 100644
--- a/arch/arm/mach-pxa/eseries.c
+++ b/arch/arm/mach-pxa/eseries.c
@@ -189,7 +189,7 @@
 
 MACHINE_START(E330, "Toshiba e330")
 	/* Maintainer: Ian Molton (spyro@f2s.com) */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa25x_map_io,
 	.nr_irqs	= ESERIES_NR_IRQS,
 	.init_irq	= pxa25x_init_irq,
@@ -239,7 +239,7 @@
 
 MACHINE_START(E350, "Toshiba e350")
 	/* Maintainer: Ian Molton (spyro@f2s.com) */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa25x_map_io,
 	.nr_irqs	= ESERIES_NR_IRQS,
 	.init_irq	= pxa25x_init_irq,
@@ -362,7 +362,7 @@
 
 MACHINE_START(E400, "Toshiba e400")
 	/* Maintainer: Ian Molton (spyro@f2s.com) */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa25x_map_io,
 	.nr_irqs	= ESERIES_NR_IRQS,
 	.init_irq	= pxa25x_init_irq,
@@ -551,7 +551,7 @@
 
 MACHINE_START(E740, "Toshiba e740")
 	/* Maintainer: Ian Molton (spyro@f2s.com) */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa25x_map_io,
 	.nr_irqs	= ESERIES_NR_IRQS,
 	.init_irq	= pxa25x_init_irq,
@@ -743,7 +743,7 @@
 
 MACHINE_START(E750, "Toshiba e750")
 	/* Maintainer: Ian Molton (spyro@f2s.com) */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa25x_map_io,
 	.nr_irqs	= ESERIES_NR_IRQS,
 	.init_irq	= pxa25x_init_irq,
@@ -948,7 +948,7 @@
 
 MACHINE_START(E800, "Toshiba e800")
 	/* Maintainer: Ian Molton (spyro@f2s.com) */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa25x_map_io,
 	.nr_irqs	= ESERIES_NR_IRQS,
 	.init_irq	= pxa25x_init_irq,
diff --git a/arch/arm/mach-pxa/ezx.c b/arch/arm/mach-pxa/ezx.c
index b73eadb..8308eee 100644
--- a/arch/arm/mach-pxa/ezx.c
+++ b/arch/arm/mach-pxa/ezx.c
@@ -797,7 +797,7 @@
 }
 
 MACHINE_START(EZX_A780, "Motorola EZX A780")
-	.boot_params    = 0xa0000100,
+	.atag_offset    = 0x100,
 	.map_io         = pxa27x_map_io,
 	.nr_irqs	= EZX_NR_IRQS,
 	.init_irq       = pxa27x_init_irq,
@@ -863,7 +863,7 @@
 }
 
 MACHINE_START(EZX_E680, "Motorola EZX E680")
-	.boot_params    = 0xa0000100,
+	.atag_offset    = 0x100,
 	.map_io         = pxa27x_map_io,
 	.nr_irqs	= EZX_NR_IRQS,
 	.init_irq       = pxa27x_init_irq,
@@ -929,7 +929,7 @@
 }
 
 MACHINE_START(EZX_A1200, "Motorola EZX A1200")
-	.boot_params    = 0xa0000100,
+	.atag_offset    = 0x100,
 	.map_io         = pxa27x_map_io,
 	.nr_irqs	= EZX_NR_IRQS,
 	.init_irq       = pxa27x_init_irq,
@@ -1120,7 +1120,7 @@
 }
 
 MACHINE_START(EZX_A910, "Motorola EZX A910")
-	.boot_params    = 0xa0000100,
+	.atag_offset    = 0x100,
 	.map_io         = pxa27x_map_io,
 	.nr_irqs	= EZX_NR_IRQS,
 	.init_irq       = pxa27x_init_irq,
@@ -1186,7 +1186,7 @@
 }
 
 MACHINE_START(EZX_E6, "Motorola EZX E6")
-	.boot_params    = 0xa0000100,
+	.atag_offset    = 0x100,
 	.map_io         = pxa27x_map_io,
 	.nr_irqs	= EZX_NR_IRQS,
 	.init_irq       = pxa27x_init_irq,
@@ -1226,7 +1226,7 @@
 }
 
 MACHINE_START(EZX_E2, "Motorola EZX E2")
-	.boot_params    = 0xa0000100,
+	.atag_offset    = 0x100,
 	.map_io         = pxa27x_map_io,
 	.nr_irqs	= EZX_NR_IRQS,
 	.init_irq       = pxa27x_init_irq,
diff --git a/arch/arm/mach-pxa/gumstix.c b/arch/arm/mach-pxa/gumstix.c
index deaa111..9c8208c 100644
--- a/arch/arm/mach-pxa/gumstix.c
+++ b/arch/arm/mach-pxa/gumstix.c
@@ -233,7 +233,7 @@
 }
 
 MACHINE_START(GUMSTIX, "Gumstix")
-	.boot_params	= 0xa0000100, /* match u-boot bi_boot_params */
+	.atag_offset	= 0x100, /* match u-boot bi_boot_params */
 	.map_io		= pxa25x_map_io,
 	.init_irq	= pxa25x_init_irq,
 	.handle_irq	= pxa25x_handle_irq,
diff --git a/arch/arm/mach-pxa/h5000.c b/arch/arm/mach-pxa/h5000.c
index 0a235128..4b5e110 100644
--- a/arch/arm/mach-pxa/h5000.c
+++ b/arch/arm/mach-pxa/h5000.c
@@ -203,7 +203,7 @@
 }
 
 MACHINE_START(H5400, "HP iPAQ H5000")
-	.boot_params = 0xa0000100,
+	.atag_offset = 0x100,
 	.map_io = pxa25x_map_io,
 	.init_irq = pxa25x_init_irq,
 	.handle_irq = pxa25x_handle_irq,
diff --git a/arch/arm/mach-pxa/himalaya.c b/arch/arm/mach-pxa/himalaya.c
index a997d0ab..f2c3245 100644
--- a/arch/arm/mach-pxa/himalaya.c
+++ b/arch/arm/mach-pxa/himalaya.c
@@ -158,7 +158,7 @@
 
 
 MACHINE_START(HIMALAYA, "HTC Himalaya")
-	.boot_params = 0xa0000100,
+	.atag_offset = 0x100,
 	.map_io = pxa25x_map_io,
 	.init_irq = pxa25x_init_irq,
 	.handle_irq = pxa25x_handle_irq,
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index c748a47..6f6368e 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -838,7 +838,7 @@
 }
 
 MACHINE_START(H4700, "HP iPAQ HX4700")
-	.boot_params  = 0xa0000100,
+	.atag_offset  = 0x100,
 	.map_io       = pxa27x_map_io,
 	.nr_irqs      = HX4700_NR_IRQS,
 	.init_irq     = pxa27x_init_irq,
diff --git a/arch/arm/mach-pxa/icontrol.c b/arch/arm/mach-pxa/icontrol.c
index d427429..f78d5db 100644
--- a/arch/arm/mach-pxa/icontrol.c
+++ b/arch/arm/mach-pxa/icontrol.c
@@ -191,7 +191,7 @@
 }
 
 MACHINE_START(ICONTROL, "iControl/SafeTcam boards using Embedian MXM-8x10 CoM")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa3xx_map_io,
 	.init_irq	= pxa3xx_init_irq,
 	.handle_irq	= pxa3xx_handle_irq,
diff --git a/arch/arm/mach-pxa/include/mach/debug-macro.S b/arch/arm/mach-pxa/include/mach/debug-macro.S
index 7d5c751..70b112e 100644
--- a/arch/arm/mach-pxa/include/mach/debug-macro.S
+++ b/arch/arm/mach-pxa/include/mach/debug-macro.S
@@ -13,7 +13,7 @@
 
 #include "hardware.h"
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00100000
 		orr	\rv, \rp, #io_p2v(0x40000000)	@ virtual
 		orr	\rp, \rp, #0x40000000		@ physical
diff --git a/arch/arm/mach-pxa/include/mach/memory.h b/arch/arm/mach-pxa/include/mach/memory.h
deleted file mode 100644
index d05a597..0000000
--- a/arch/arm/mach-pxa/include/mach/memory.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/*
- *  arch/arm/mach-pxa/include/mach/memory.h
- *
- * Author:	Nicolas Pitre
- * Copyright:	(C) 2001 MontaVista Software Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET	UL(0xa0000000)
-
-#endif
diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c
index b09e848..ca60757 100644
--- a/arch/arm/mach-pxa/irq.c
+++ b/arch/arm/mach-pxa/irq.c
@@ -19,6 +19,8 @@
 #include <linux/io.h>
 #include <linux/irq.h>
 
+#include <asm/exception.h>
+
 #include <mach/hardware.h>
 #include <mach/irqs.h>
 #include <mach/gpio.h>
diff --git a/arch/arm/mach-pxa/littleton.c b/arch/arm/mach-pxa/littleton.c
index 8f97e15..0037e57 100644
--- a/arch/arm/mach-pxa/littleton.c
+++ b/arch/arm/mach-pxa/littleton.c
@@ -437,7 +437,7 @@
 }
 
 MACHINE_START(LITTLETON, "Marvell Form Factor Development Platform (aka Littleton)")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa3xx_map_io,
 	.nr_irqs	= LITTLETON_NR_IRQS,
 	.init_irq	= pxa3xx_init_irq,
diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c
index c171d6e..16df0fc0 100644
--- a/arch/arm/mach-pxa/lpd270.c
+++ b/arch/arm/mach-pxa/lpd270.c
@@ -499,7 +499,7 @@
 
 MACHINE_START(LOGICPD_PXA270, "LogicPD PXA270 Card Engine")
 	/* Maintainer: Peter Barada */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= lpd270_map_io,
 	.nr_irqs	= LPD270_NR_IRQS,
 	.init_irq	= lpd270_init_irq,
diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c
index 5fe5bcd..4b796c3 100644
--- a/arch/arm/mach-pxa/magician.c
+++ b/arch/arm/mach-pxa/magician.c
@@ -753,7 +753,7 @@
 
 
 MACHINE_START(MAGICIAN, "HTC Magician")
-	.boot_params = 0xa0000100,
+	.atag_offset = 0x100,
 	.map_io = pxa27x_map_io,
 	.nr_irqs = MAGICIAN_NR_IRQS,
 	.init_irq = pxa27x_init_irq,
diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c
index 4622eb7..cc6e14f 100644
--- a/arch/arm/mach-pxa/mainstone.c
+++ b/arch/arm/mach-pxa/mainstone.c
@@ -616,7 +616,7 @@
 
 MACHINE_START(MAINSTONE, "Intel HCDDBBVA0 Development Platform (aka Mainstone)")
 	/* Maintainer: MontaVista Software Inc. */
-	.boot_params	= 0xa0000100,	/* BLOB boot parameter setting */
+	.atag_offset	= 0x100,	/* BLOB boot parameter setting */
 	.map_io		= mainstone_map_io,
 	.nr_irqs	= MAINSTONE_NR_IRQS,
 	.init_irq	= mainstone_init_irq,
diff --git a/arch/arm/mach-pxa/mioa701.c b/arch/arm/mach-pxa/mioa701.c
index 64810f9..b938fc2 100644
--- a/arch/arm/mach-pxa/mioa701.c
+++ b/arch/arm/mach-pxa/mioa701.c
@@ -751,7 +751,7 @@
 }
 
 MACHINE_START(MIOA701, "MIO A701")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= &pxa27x_map_io,
 	.init_irq	= &pxa27x_init_irq,
 	.handle_irq	= &pxa27x_handle_irq,
diff --git a/arch/arm/mach-pxa/mp900.c b/arch/arm/mach-pxa/mp900.c
index fb408861..4af5d51 100644
--- a/arch/arm/mach-pxa/mp900.c
+++ b/arch/arm/mach-pxa/mp900.c
@@ -92,7 +92,7 @@
 
 /* Maintainer - Michael Petchkovsky <mkpetch@internode.on.net> */
 MACHINE_START(NEC_MP900, "MobilePro900/C")
-	.boot_params	= 0xa0220100,
+	.atag_offset	= 0x220100,
 	.timer		= &pxa_timer,
 	.map_io		= pxa25x_map_io,
 	.init_irq	= pxa25x_init_irq,
diff --git a/arch/arm/mach-pxa/palmld.c b/arch/arm/mach-pxa/palmld.c
index 6b77365..3d4a281 100644
--- a/arch/arm/mach-pxa/palmld.c
+++ b/arch/arm/mach-pxa/palmld.c
@@ -342,7 +342,7 @@
 }
 
 MACHINE_START(PALMLD, "Palm LifeDrive")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= palmld_map_io,
 	.init_irq	= pxa27x_init_irq,
 	.handle_irq	= pxa27x_handle_irq,
diff --git a/arch/arm/mach-pxa/palmt5.c b/arch/arm/mach-pxa/palmt5.c
index 9bd3e47..99d6bcf 100644
--- a/arch/arm/mach-pxa/palmt5.c
+++ b/arch/arm/mach-pxa/palmt5.c
@@ -202,7 +202,7 @@
 }
 
 MACHINE_START(PALMT5, "Palm Tungsten|T5")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa27x_map_io,
 	.reserve	= palmt5_reserve,
 	.init_irq	= pxa27x_init_irq,
diff --git a/arch/arm/mach-pxa/palmtc.c b/arch/arm/mach-pxa/palmtc.c
index 6ad4a6c..6ec7cae 100644
--- a/arch/arm/mach-pxa/palmtc.c
+++ b/arch/arm/mach-pxa/palmtc.c
@@ -537,7 +537,7 @@
 };
 
 MACHINE_START(PALMTC, "Palm Tungsten|C")
-	.boot_params 	= 0xa0000100,
+	.atag_offset 	= 0x100,
 	.map_io		= pxa25x_map_io,
 	.init_irq	= pxa25x_init_irq,
 	.handle_irq	= pxa25x_handle_irq,
diff --git a/arch/arm/mach-pxa/palmte2.c b/arch/arm/mach-pxa/palmte2.c
index 664232f..9376da0 100644
--- a/arch/arm/mach-pxa/palmte2.c
+++ b/arch/arm/mach-pxa/palmte2.c
@@ -356,7 +356,7 @@
 }
 
 MACHINE_START(PALMTE2, "Palm Tungsten|E2")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa25x_map_io,
 	.init_irq	= pxa25x_init_irq,
 	.handle_irq	= pxa25x_handle_irq,
diff --git a/arch/arm/mach-pxa/palmtreo.c b/arch/arm/mach-pxa/palmtreo.c
index bb27d4b..7346fbf 100644
--- a/arch/arm/mach-pxa/palmtreo.c
+++ b/arch/arm/mach-pxa/palmtreo.c
@@ -440,7 +440,7 @@
 }
 
 MACHINE_START(TREO680, "Palm Treo 680")
-	.boot_params    = 0xa0000100,
+	.atag_offset    = 0x100,
 	.map_io         = pxa27x_map_io,
 	.reserve	= treo_reserve,
 	.init_irq       = pxa27x_init_irq,
@@ -450,7 +450,7 @@
 MACHINE_END
 
 MACHINE_START(CENTRO, "Palm Centro 685")
-	.boot_params    = 0xa0000100,
+	.atag_offset    = 0x100,
 	.map_io         = pxa27x_map_io,
 	.reserve	= treo_reserve,
 	.init_irq       = pxa27x_init_irq,
diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c
index fc428558..2b9e76f 100644
--- a/arch/arm/mach-pxa/palmtx.c
+++ b/arch/arm/mach-pxa/palmtx.c
@@ -364,7 +364,7 @@
 }
 
 MACHINE_START(PALMTX, "Palm T|X")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= palmtx_map_io,
 	.init_irq	= pxa27x_init_irq,
 	.handle_irq	= pxa27x_handle_irq,
diff --git a/arch/arm/mach-pxa/palmz72.c b/arch/arm/mach-pxa/palmz72.c
index e61c1cc..68e18ba 100644
--- a/arch/arm/mach-pxa/palmz72.c
+++ b/arch/arm/mach-pxa/palmz72.c
@@ -399,7 +399,7 @@
 }
 
 MACHINE_START(PALMZ72, "Palm Zire72")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa27x_map_io,
 	.init_irq	= pxa27x_init_irq,
 	.handle_irq	= pxa27x_handle_irq,
diff --git a/arch/arm/mach-pxa/pcm027.c b/arch/arm/mach-pxa/pcm027.c
index ffa65df..0b825a3 100644
--- a/arch/arm/mach-pxa/pcm027.c
+++ b/arch/arm/mach-pxa/pcm027.c
@@ -258,7 +258,7 @@
 
 MACHINE_START(PCM027, "Phytec Messtechnik GmbH phyCORE-PXA270")
 	/* Maintainer: Pengutronix */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pcm027_map_io,
 	.nr_irqs	= PCM027_NR_IRQS,
 	.init_irq	= pxa27x_init_irq,
diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c
index bbcd905..6810cdd 100644
--- a/arch/arm/mach-pxa/raumfeld.c
+++ b/arch/arm/mach-pxa/raumfeld.c
@@ -1086,7 +1086,7 @@
 
 #ifdef CONFIG_MACH_RAUMFELD_RC
 MACHINE_START(RAUMFELD_RC, "Raumfeld Controller")
-	.boot_params	= RAUMFELD_SDRAM_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.init_machine	= raumfeld_controller_init,
 	.map_io		= pxa3xx_map_io,
 	.init_irq	= pxa3xx_init_irq,
@@ -1097,7 +1097,7 @@
 
 #ifdef CONFIG_MACH_RAUMFELD_CONNECTOR
 MACHINE_START(RAUMFELD_CONNECTOR, "Raumfeld Connector")
-	.boot_params	= RAUMFELD_SDRAM_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.init_machine	= raumfeld_connector_init,
 	.map_io		= pxa3xx_map_io,
 	.init_irq	= pxa3xx_init_irq,
@@ -1108,7 +1108,7 @@
 
 #ifdef CONFIG_MACH_RAUMFELD_SPEAKER
 MACHINE_START(RAUMFELD_SPEAKER, "Raumfeld Speaker")
-	.boot_params	= RAUMFELD_SDRAM_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.init_machine	= raumfeld_speaker_init,
 	.map_io		= pxa3xx_map_io,
 	.init_irq	= pxa3xx_init_irq,
diff --git a/arch/arm/mach-pxa/saar.c b/arch/arm/mach-pxa/saar.c
index df4356e..602d70b 100644
--- a/arch/arm/mach-pxa/saar.c
+++ b/arch/arm/mach-pxa/saar.c
@@ -596,7 +596,7 @@
 
 MACHINE_START(SAAR, "PXA930 Handheld Platform (aka SAAR)")
 	/* Maintainer: Eric Miao <eric.miao@marvell.com> */
-	.boot_params    = 0xa0000100,
+	.atag_offset    = 0x100,
 	.map_io         = pxa3xx_map_io,
 	.init_irq       = pxa3xx_init_irq,
 	.handle_irq       = pxa3xx_handle_irq,
diff --git a/arch/arm/mach-pxa/saarb.c b/arch/arm/mach-pxa/saarb.c
index ebd6379..5ce3403 100644
--- a/arch/arm/mach-pxa/saarb.c
+++ b/arch/arm/mach-pxa/saarb.c
@@ -103,7 +103,7 @@
 }
 
 MACHINE_START(SAARB, "PXA955 Handheld Platform (aka SAARB)")
-	.boot_params    = 0xa0000100,
+	.atag_offset    = 0x100,
 	.map_io         = pxa3xx_map_io,
 	.nr_irqs	= SAARB_NR_IRQS,
 	.init_irq       = pxa95x_init_irq,
diff --git a/arch/arm/mach-pxa/stargate2.c b/arch/arm/mach-pxa/stargate2.c
index 3f8d0af..4c9a48b 100644
--- a/arch/arm/mach-pxa/stargate2.c
+++ b/arch/arm/mach-pxa/stargate2.c
@@ -1004,7 +1004,7 @@
 	.handle_irq	= pxa27x_handle_irq,
 	.timer		= &pxa_timer,
 	.init_machine	= imote2_init,
-	.boot_params	= 0xA0000100,
+	.atag_offset	= 0x100,
 MACHINE_END
 #endif
 
@@ -1016,6 +1016,6 @@
 	.handle_irq = pxa27x_handle_irq,
 	.timer = &pxa_timer,
 	.init_machine = stargate2_init,
-	.boot_params = 0xA0000100,
+	.atag_offset = 0x100,
 MACHINE_END
 #endif
diff --git a/arch/arm/mach-pxa/tavorevb.c b/arch/arm/mach-pxa/tavorevb.c
index 32fb58e..ad47bb9 100644
--- a/arch/arm/mach-pxa/tavorevb.c
+++ b/arch/arm/mach-pxa/tavorevb.c
@@ -489,7 +489,7 @@
 
 MACHINE_START(TAVOREVB, "PXA930 Evaluation Board (aka TavorEVB)")
 	/* Maintainer: Eric Miao <eric.miao@marvell.com> */
-	.boot_params    = 0xa0000100,
+	.atag_offset    = 0x100,
 	.map_io         = pxa3xx_map_io,
 	.init_irq       = pxa3xx_init_irq,
 	.handle_irq       = pxa3xx_handle_irq,
diff --git a/arch/arm/mach-pxa/tavorevb3.c b/arch/arm/mach-pxa/tavorevb3.c
index fd5a8ea..fd56916 100644
--- a/arch/arm/mach-pxa/tavorevb3.c
+++ b/arch/arm/mach-pxa/tavorevb3.c
@@ -125,7 +125,7 @@
 }
 
 MACHINE_START(TAVOREVB3, "PXA950 Evaluation Board (aka TavorEVB3)")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io         = pxa3xx_map_io,
 	.nr_irqs	= TAVOREVB3_NR_IRQS,
 	.init_irq       = pxa3xx_init_irq,
diff --git a/arch/arm/mach-pxa/trizeps4.c b/arch/arm/mach-pxa/trizeps4.c
index c041750..35bbf13 100644
--- a/arch/arm/mach-pxa/trizeps4.c
+++ b/arch/arm/mach-pxa/trizeps4.c
@@ -554,7 +554,7 @@
 
 MACHINE_START(TRIZEPS4, "Keith und Koep Trizeps IV module")
 	/* MAINTAINER("Jürgen Schindele") */
-	.boot_params	= TRIZEPS4_SDRAM_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.init_machine	= trizeps4_init,
 	.map_io		= trizeps4_map_io,
 	.init_irq	= pxa27x_init_irq,
@@ -564,7 +564,7 @@
 
 MACHINE_START(TRIZEPS4WL, "Keith und Koep Trizeps IV-WL module")
 	/* MAINTAINER("Jürgen Schindele") */
-	.boot_params	= TRIZEPS4_SDRAM_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.init_machine	= trizeps4_init,
 	.map_io		= trizeps4_map_io,
 	.init_irq	= pxa27x_init_irq,
diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c
index d4a3dc7..242ddae 100644
--- a/arch/arm/mach-pxa/viper.c
+++ b/arch/arm/mach-pxa/viper.c
@@ -992,7 +992,7 @@
 
 MACHINE_START(VIPER, "Arcom/Eurotech VIPER SBC")
 	/* Maintainer: Marc Zyngier <maz@misterjones.org> */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= viper_map_io,
 	.init_irq	= viper_init_irq,
 	.handle_irq	= pxa25x_handle_irq,
diff --git a/arch/arm/mach-pxa/vpac270.c b/arch/arm/mach-pxa/vpac270.c
index 5f8490a..a7539a6 100644
--- a/arch/arm/mach-pxa/vpac270.c
+++ b/arch/arm/mach-pxa/vpac270.c
@@ -716,7 +716,7 @@
 }
 
 MACHINE_START(VPAC270, "Voipac PXA270")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa27x_map_io,
 	.init_irq	= pxa27x_init_irq,
 	.handle_irq	= pxa27x_handle_irq,
diff --git a/arch/arm/mach-pxa/xcep.c b/arch/arm/mach-pxa/xcep.c
index acc600f..54930cc 100644
--- a/arch/arm/mach-pxa/xcep.c
+++ b/arch/arm/mach-pxa/xcep.c
@@ -180,7 +180,7 @@
 }
 
 MACHINE_START(XCEP, "Iskratel XCEP")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.init_machine	= xcep_init,
 	.map_io		= pxa25x_map_io,
 	.init_irq	= pxa25x_init_irq,
diff --git a/arch/arm/mach-pxa/z2.c b/arch/arm/mach-pxa/z2.c
index 6c9275a..84ed72d 100644
--- a/arch/arm/mach-pxa/z2.c
+++ b/arch/arm/mach-pxa/z2.c
@@ -686,7 +686,7 @@
 	 */
 	PSPR = 0x0;
 	local_irq_disable();
-	pxa27x_cpu_suspend(PWRMODE_DEEPSLEEP, PLAT_PHYS_OFFSET - PAGE_OFFSET);
+	pxa27x_cpu_suspend(PWRMODE_DEEPSLEEP, PHYS_OFFSET - PAGE_OFFSET);
 }
 #else
 #define z2_power_off   NULL
@@ -718,7 +718,7 @@
 }
 
 MACHINE_START(ZIPIT2, "Zipit Z2")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa27x_map_io,
 	.init_irq	= pxa27x_init_irq,
 	.handle_irq	= pxa27x_handle_irq,
diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c
index 99c49bc..c424e7d 100644
--- a/arch/arm/mach-pxa/zeus.c
+++ b/arch/arm/mach-pxa/zeus.c
@@ -904,7 +904,7 @@
 
 MACHINE_START(ARCOM_ZEUS, "Arcom/Eurotech ZEUS")
 	/* Maintainer: Marc Zyngier <maz@misterjones.org> */
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= zeus_map_io,
 	.nr_irqs	= ZEUS_NR_IRQS,
 	.init_irq	= zeus_init_irq,
diff --git a/arch/arm/mach-pxa/zylonite.c b/arch/arm/mach-pxa/zylonite.c
index 15ec66b..31d4968 100644
--- a/arch/arm/mach-pxa/zylonite.c
+++ b/arch/arm/mach-pxa/zylonite.c
@@ -422,7 +422,7 @@
 }
 
 MACHINE_START(ZYLONITE, "PXA3xx Platform Development Kit (aka Zylonite)")
-	.boot_params	= 0xa0000100,
+	.atag_offset	= 0x100,
 	.map_io		= pxa3xx_map_io,
 	.nr_irqs	= ZYLONITE_NR_IRQS,
 	.init_irq	= pxa3xx_init_irq,
diff --git a/arch/arm/mach-realview/include/mach/debug-macro.S b/arch/arm/mach-realview/include/mach/debug-macro.S
index 90b687c..fb4901c 100644
--- a/arch/arm/mach-realview/include/mach/debug-macro.S
+++ b/arch/arm/mach-realview/include/mach/debug-macro.S
@@ -33,7 +33,7 @@
 #error "Unknown RealView platform"
 #endif
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #DEBUG_LL_UART_OFFSET
 		orr	\rv, \rp, #0xfb000000	@ virtual base
 		orr	\rp, \rp, #0x10000000	@ physical base
diff --git a/arch/arm/mach-realview/platsmp.c b/arch/arm/mach-realview/platsmp.c
index 4ae943b..e83c654 100644
--- a/arch/arm/mach-realview/platsmp.c
+++ b/arch/arm/mach-realview/platsmp.c
@@ -52,12 +52,10 @@
 	ncores = scu_base ? scu_get_core_count(scu_base) : 1;
 
 	/* sanity check */
-	if (ncores > NR_CPUS) {
-		printk(KERN_WARNING
-		       "Realview: no. of cores (%d) greater than configured "
-		       "maximum of %d - clipping\n",
-		       ncores, NR_CPUS);
-		ncores = NR_CPUS;
+	if (ncores > nr_cpu_ids) {
+		pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+			ncores, nr_cpu_ids);
+		ncores = nr_cpu_ids;
 	}
 
 	for (i = 0; i < ncores; i++)
diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c
index 7a4e3b1..026c66a 100644
--- a/arch/arm/mach-realview/realview_eb.c
+++ b/arch/arm/mach-realview/realview_eb.c
@@ -463,7 +463,7 @@
 
 MACHINE_START(REALVIEW_EB, "ARM-RealView EB")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.boot_params	= PLAT_PHYS_OFFSET + 0x00000100,
+	.atag_offset	= 0x100,
 	.fixup		= realview_fixup,
 	.map_io		= realview_eb_map_io,
 	.init_early	= realview_init_early,
diff --git a/arch/arm/mach-realview/realview_pb1176.c b/arch/arm/mach-realview/realview_pb1176.c
index ad5671a..7263dea 100644
--- a/arch/arm/mach-realview/realview_pb1176.c
+++ b/arch/arm/mach-realview/realview_pb1176.c
@@ -358,7 +358,7 @@
 
 MACHINE_START(REALVIEW_PB1176, "ARM-RealView PB1176")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.boot_params	= PLAT_PHYS_OFFSET + 0x00000100,
+	.atag_offset	= 0x100,
 	.fixup		= realview_pb1176_fixup,
 	.map_io		= realview_pb1176_map_io,
 	.init_early	= realview_init_early,
diff --git a/arch/arm/mach-realview/realview_pb11mp.c b/arch/arm/mach-realview/realview_pb11mp.c
index b43644b..671ad6d 100644
--- a/arch/arm/mach-realview/realview_pb11mp.c
+++ b/arch/arm/mach-realview/realview_pb11mp.c
@@ -360,7 +360,7 @@
 
 MACHINE_START(REALVIEW_PB11MP, "ARM-RealView PB11MPCore")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.boot_params	= PLAT_PHYS_OFFSET + 0x00000100,
+	.atag_offset	= 0x100,
 	.fixup		= realview_fixup,
 	.map_io		= realview_pb11mp_map_io,
 	.init_early	= realview_init_early,
diff --git a/arch/arm/mach-realview/realview_pba8.c b/arch/arm/mach-realview/realview_pba8.c
index 763e8f3..cbf22df 100644
--- a/arch/arm/mach-realview/realview_pba8.c
+++ b/arch/arm/mach-realview/realview_pba8.c
@@ -310,7 +310,7 @@
 
 MACHINE_START(REALVIEW_PBA8, "ARM-RealView PB-A8")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.boot_params	= PLAT_PHYS_OFFSET + 0x00000100,
+	.atag_offset	= 0x100,
 	.fixup		= realview_fixup,
 	.map_io		= realview_pba8_map_io,
 	.init_early	= realview_init_early,
diff --git a/arch/arm/mach-realview/realview_pbx.c b/arch/arm/mach-realview/realview_pbx.c
index 363b0ab..8ec7e52 100644
--- a/arch/arm/mach-realview/realview_pbx.c
+++ b/arch/arm/mach-realview/realview_pbx.c
@@ -393,7 +393,7 @@
 
 MACHINE_START(REALVIEW_PBX, "ARM-RealView PBX")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.boot_params	= PLAT_PHYS_OFFSET + 0x00000100,
+	.atag_offset	= 0x100,
 	.fixup		= realview_pbx_fixup,
 	.map_io		= realview_pbx_map_io,
 	.init_early	= realview_init_early,
diff --git a/arch/arm/mach-rpc/include/mach/debug-macro.S b/arch/arm/mach-rpc/include/mach/debug-macro.S
index 85effff..6d28cc9 100644
--- a/arch/arm/mach-rpc/include/mach/debug-macro.S
+++ b/arch/arm/mach-rpc/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00010000
 		orr	\rp, \rp, #0x00000fe0
 		orr	\rv, \rp, #0xe0000000	@ virtual
diff --git a/arch/arm/mach-rpc/riscpc.c b/arch/arm/mach-rpc/riscpc.c
index 580b3c7..a9241eb 100644
--- a/arch/arm/mach-rpc/riscpc.c
+++ b/arch/arm/mach-rpc/riscpc.c
@@ -218,7 +218,7 @@
 
 MACHINE_START(RISCPC, "Acorn-RiscPC")
 	/* Maintainer: Russell King */
-	.boot_params	= 0x10000100,
+	.atag_offset	= 0x100,
 	.reserve_lp0	= 1,
 	.reserve_lp1	= 1,
 	.map_io		= rpc_map_io,
diff --git a/arch/arm/mach-s3c2400/include/mach/memory.h b/arch/arm/mach-s3c2400/include/mach/memory.h
deleted file mode 100644
index 3f33670..0000000
--- a/arch/arm/mach-s3c2400/include/mach/memory.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/* arch/arm/mach-s3c2400/include/mach/memory.h
- *  from arch/arm/mach-rpc/include/mach/memory.h
- *
- *  Copyright 2007 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *
- *  Copyright (C) 1996,1997,1998 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET	UL(0x0C000000)
-
-#endif
diff --git a/arch/arm/mach-s3c2410/include/mach/debug-macro.S b/arch/arm/mach-s3c2410/include/mach/debug-macro.S
index 5882dea..4135de8 100644
--- a/arch/arm/mach-s3c2410/include/mach/debug-macro.S
+++ b/arch/arm/mach-s3c2410/include/mach/debug-macro.S
@@ -19,7 +19,7 @@
 #define S3C2410_UART1_OFF (0x4000)
 #define SHIFT_2440TXF (14-9)
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C24XX_PA_UART
 		ldr	\rv, = S3C24XX_VA_UART
 #if CONFIG_DEBUG_S3C_UART != 0
diff --git a/arch/arm/mach-s3c2410/include/mach/memory.h b/arch/arm/mach-s3c2410/include/mach/memory.h
deleted file mode 100644
index f92b97b..0000000
--- a/arch/arm/mach-s3c2410/include/mach/memory.h
+++ /dev/null
@@ -1,16 +0,0 @@
-/* arch/arm/mach-s3c2410/include/mach/memory.h
- *  from arch/arm/mach-rpc/include/mach/memory.h
- *
- *  Copyright (C) 1996,1997,1998 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET	UL(0x30000000)
-
-#endif
diff --git a/arch/arm/mach-s3c2410/mach-amlm5900.c b/arch/arm/mach-s3c2410/mach-amlm5900.c
index dabc141..7983894 100644
--- a/arch/arm/mach-s3c2410/mach-amlm5900.c
+++ b/arch/arm/mach-s3c2410/mach-amlm5900.c
@@ -236,7 +236,7 @@
 }
 
 MACHINE_START(AML_M5900, "AML_M5900")
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= amlm5900_map_io,
 	.init_irq	= s3c24xx_init_irq,
 	.init_machine	= amlm5900_init,
diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c
index 1e2d536..a20ae1a 100644
--- a/arch/arm/mach-s3c2410/mach-bast.c
+++ b/arch/arm/mach-s3c2410/mach-bast.c
@@ -657,7 +657,7 @@
 
 MACHINE_START(BAST, "Simtec-BAST")
 	/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= bast_map_io,
 	.init_irq	= s3c24xx_init_irq,
 	.init_machine	= bast_init,
diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c
index 2a2fa06..556c535 100644
--- a/arch/arm/mach-s3c2410/mach-h1940.c
+++ b/arch/arm/mach-s3c2410/mach-h1940.c
@@ -744,7 +744,7 @@
 
 MACHINE_START(H1940, "IPAQ-H1940")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= h1940_map_io,
 	.reserve	= h1940_reserve,
 	.init_irq	= h1940_init_irq,
diff --git a/arch/arm/mach-s3c2410/mach-n30.c b/arch/arm/mach-s3c2410/mach-n30.c
index 079dcaa..1dc3e32 100644
--- a/arch/arm/mach-s3c2410/mach-n30.c
+++ b/arch/arm/mach-s3c2410/mach-n30.c
@@ -586,7 +586,7 @@
 	/* Maintainer: Christer Weinigel <christer@weinigel.se>,
 				Ben Dooks <ben-linux@fluff.org>
 	*/
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.timer		= &s3c24xx_timer,
 	.init_machine	= n30_init,
 	.init_irq	= s3c24xx_init_irq,
@@ -596,7 +596,7 @@
 MACHINE_START(N35, "Acer-N35")
 	/* Maintainer: Christer Weinigel <christer@weinigel.se>
 	*/
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.timer		= &s3c24xx_timer,
 	.init_machine	= n30_init,
 	.init_irq	= s3c24xx_init_irq,
diff --git a/arch/arm/mach-s3c2410/mach-otom.c b/arch/arm/mach-s3c2410/mach-otom.c
index 0aa16cd..f03f3fd 100644
--- a/arch/arm/mach-s3c2410/mach-otom.c
+++ b/arch/arm/mach-s3c2410/mach-otom.c
@@ -116,7 +116,7 @@
 
 MACHINE_START(OTOM, "Nex Vision - Otom 1.1")
 	/* Maintainer: Guillaume GOURAT <guillaume.gourat@nexvision.tv> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= otom11_map_io,
 	.init_machine	= otom11_init,
 	.init_irq	= s3c24xx_init_irq,
diff --git a/arch/arm/mach-s3c2410/mach-qt2410.c b/arch/arm/mach-s3c2410/mach-qt2410.c
index f44f775..367d376 100644
--- a/arch/arm/mach-s3c2410/mach-qt2410.c
+++ b/arch/arm/mach-s3c2410/mach-qt2410.c
@@ -344,7 +344,7 @@
 }
 
 MACHINE_START(QT2410, "QT2410")
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= qt2410_map_io,
 	.init_irq	= s3c24xx_init_irq,
 	.init_machine	= qt2410_machine_init,
diff --git a/arch/arm/mach-s3c2410/mach-smdk2410.c b/arch/arm/mach-s3c2410/mach-smdk2410.c
index e17f033..99c9dfd 100644
--- a/arch/arm/mach-s3c2410/mach-smdk2410.c
+++ b/arch/arm/mach-s3c2410/mach-smdk2410.c
@@ -111,7 +111,7 @@
 MACHINE_START(SMDK2410, "SMDK2410") /* @TODO: request a new identifier and switch
 				    * to SMDK2410 */
 	/* Maintainer: Jonas Dietsche */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= smdk2410_map_io,
 	.init_irq	= s3c24xx_init_irq,
 	.init_machine	= smdk2410_init,
diff --git a/arch/arm/mach-s3c2410/mach-tct_hammer.c b/arch/arm/mach-s3c2410/mach-tct_hammer.c
index 43c2b83..e0d0b6f 100644
--- a/arch/arm/mach-s3c2410/mach-tct_hammer.c
+++ b/arch/arm/mach-s3c2410/mach-tct_hammer.c
@@ -146,7 +146,7 @@
 }
 
 MACHINE_START(TCT_HAMMER, "TCT_HAMMER")
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= tct_hammer_map_io,
 	.init_irq	= s3c24xx_init_irq,
 	.init_machine	= tct_hammer_init,
diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c
index 6ccce5a..df47e8e 100644
--- a/arch/arm/mach-s3c2410/mach-vr1000.c
+++ b/arch/arm/mach-s3c2410/mach-vr1000.c
@@ -400,7 +400,7 @@
 
 MACHINE_START(VR1000, "Thorcom-VR1000")
 	/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= vr1000_map_io,
 	.init_machine	= vr1000_init,
 	.init_irq	= s3c24xx_init_irq,
diff --git a/arch/arm/mach-s3c2412/mach-jive.c b/arch/arm/mach-s3c2412/mach-jive.c
index 5eeb475..286ef17 100644
--- a/arch/arm/mach-s3c2412/mach-jive.c
+++ b/arch/arm/mach-s3c2412/mach-jive.c
@@ -655,7 +655,7 @@
 
 MACHINE_START(JIVE, "JIVE")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 
 	.init_irq	= s3c24xx_init_irq,
 	.map_io		= jive_map_io,
diff --git a/arch/arm/mach-s3c2412/mach-smdk2413.c b/arch/arm/mach-s3c2412/mach-smdk2413.c
index 834cfb6..d6325ede 100644
--- a/arch/arm/mach-s3c2412/mach-smdk2413.c
+++ b/arch/arm/mach-s3c2412/mach-smdk2413.c
@@ -128,7 +128,7 @@
 
 MACHINE_START(S3C2413, "S3C2413")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 
 	.fixup		= smdk2413_fixup,
 	.init_irq	= s3c24xx_init_irq,
@@ -139,7 +139,7 @@
 
 MACHINE_START(SMDK2412, "SMDK2412")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 
 	.fixup		= smdk2413_fixup,
 	.init_irq	= s3c24xx_init_irq,
@@ -150,7 +150,7 @@
 
 MACHINE_START(SMDK2413, "SMDK2413")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 
 	.fixup		= smdk2413_fixup,
 	.init_irq	= s3c24xx_init_irq,
diff --git a/arch/arm/mach-s3c2412/mach-vstms.c b/arch/arm/mach-s3c2412/mach-vstms.c
index 83544eb..5955c15 100644
--- a/arch/arm/mach-s3c2412/mach-vstms.c
+++ b/arch/arm/mach-s3c2412/mach-vstms.c
@@ -156,7 +156,7 @@
 }
 
 MACHINE_START(VSTMS, "VSTMS")
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 
 	.fixup		= vstms_fixup,
 	.init_irq	= s3c24xx_init_irq,
diff --git a/arch/arm/mach-s3c2416/mach-smdk2416.c b/arch/arm/mach-s3c2416/mach-smdk2416.c
index ac27ebb..a9eee53 100644
--- a/arch/arm/mach-s3c2416/mach-smdk2416.c
+++ b/arch/arm/mach-s3c2416/mach-smdk2416.c
@@ -245,7 +245,7 @@
 
 MACHINE_START(SMDK2416, "SMDK2416")
 	/* Maintainer: Yauhen Kharuzhy <jekhor@gmail.com> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 
 	.init_irq	= s3c24xx_init_irq,
 	.map_io		= smdk2416_map_io,
diff --git a/arch/arm/mach-s3c2440/mach-anubis.c b/arch/arm/mach-s3c2440/mach-anubis.c
index d708678..74f92fc 100644
--- a/arch/arm/mach-s3c2440/mach-anubis.c
+++ b/arch/arm/mach-s3c2440/mach-anubis.c
@@ -498,7 +498,7 @@
 
 MACHINE_START(ANUBIS, "Simtec-Anubis")
 	/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= anubis_map_io,
 	.init_machine	= anubis_init,
 	.init_irq	= s3c24xx_init_irq,
diff --git a/arch/arm/mach-s3c2440/mach-at2440evb.c b/arch/arm/mach-s3c2440/mach-at2440evb.c
index 6c98b78..38887ee 100644
--- a/arch/arm/mach-s3c2440/mach-at2440evb.c
+++ b/arch/arm/mach-s3c2440/mach-at2440evb.c
@@ -233,7 +233,7 @@
 
 
 MACHINE_START(AT2440EVB, "AT2440EVB")
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= at2440evb_map_io,
 	.init_machine	= at2440evb_init,
 	.init_irq	= s3c24xx_init_irq,
diff --git a/arch/arm/mach-s3c2440/mach-gta02.c b/arch/arm/mach-s3c2440/mach-gta02.c
index c10ddf4..de1e0ff 100644
--- a/arch/arm/mach-s3c2440/mach-gta02.c
+++ b/arch/arm/mach-s3c2440/mach-gta02.c
@@ -595,7 +595,7 @@
 
 MACHINE_START(NEO1973_GTA02, "GTA02")
 	/* Maintainer: Nelson Castillo <arhuaco@freaks-unidos.net> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= gta02_map_io,
 	.init_irq	= s3c24xx_init_irq,
 	.init_machine	= gta02_machine_init,
diff --git a/arch/arm/mach-s3c2440/mach-mini2440.c b/arch/arm/mach-s3c2440/mach-mini2440.c
index fc2dc0b..91fe0b4 100644
--- a/arch/arm/mach-s3c2440/mach-mini2440.c
+++ b/arch/arm/mach-s3c2440/mach-mini2440.c
@@ -676,7 +676,7 @@
 
 MACHINE_START(MINI2440, "MINI2440")
 	/* Maintainer: Michel Pollet <buserror@gmail.com> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= mini2440_map_io,
 	.init_machine	= mini2440_init,
 	.init_irq	= s3c24xx_init_irq,
diff --git a/arch/arm/mach-s3c2440/mach-nexcoder.c b/arch/arm/mach-s3c2440/mach-nexcoder.c
index 37dd306..61c0bf1 100644
--- a/arch/arm/mach-s3c2440/mach-nexcoder.c
+++ b/arch/arm/mach-s3c2440/mach-nexcoder.c
@@ -151,7 +151,7 @@
 
 MACHINE_START(NEXCODER_2440, "NexVision - Nexcoder 2440")
 	/* Maintainer: Guillaume GOURAT <guillaume.gourat@nexvision.tv> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= nexcoder_map_io,
 	.init_machine	= nexcoder_init,
 	.init_irq	= s3c24xx_init_irq,
diff --git a/arch/arm/mach-s3c2440/mach-osiris.c b/arch/arm/mach-s3c2440/mach-osiris.c
index d885363..dc142eb 100644
--- a/arch/arm/mach-s3c2440/mach-osiris.c
+++ b/arch/arm/mach-s3c2440/mach-osiris.c
@@ -447,7 +447,7 @@
 
 MACHINE_START(OSIRIS, "Simtec-OSIRIS")
 	/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= osiris_map_io,
 	.init_irq	= s3c24xx_init_irq,
 	.init_machine	= osiris_init,
diff --git a/arch/arm/mach-s3c2440/mach-rx1950.c b/arch/arm/mach-s3c2440/mach-rx1950.c
index 27ea950..684dbb3 100644
--- a/arch/arm/mach-s3c2440/mach-rx1950.c
+++ b/arch/arm/mach-s3c2440/mach-rx1950.c
@@ -825,7 +825,7 @@
 
 MACHINE_START(RX1950, "HP iPAQ RX1950")
     /* Maintainers: Vasily Khoruzhick */
-	.boot_params = S3C2410_SDRAM_PA + 0x100,
+	.atag_offset = 0x100,
 	.map_io = rx1950_map_io,
 	.reserve	= rx1950_reserve,
 	.init_irq = s3c24xx_init_irq,
diff --git a/arch/arm/mach-s3c2440/mach-rx3715.c b/arch/arm/mach-s3c2440/mach-rx3715.c
index 1472b1a..e19499c 100644
--- a/arch/arm/mach-s3c2440/mach-rx3715.c
+++ b/arch/arm/mach-s3c2440/mach-rx3715.c
@@ -218,7 +218,7 @@
 
 MACHINE_START(RX3715, "IPAQ-RX3715")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= rx3715_map_io,
 	.reserve	= rx3715_reserve,
 	.init_irq	= rx3715_init_irq,
diff --git a/arch/arm/mach-s3c2440/mach-smdk2440.c b/arch/arm/mach-s3c2440/mach-smdk2440.c
index eedfe0f..36eeb41 100644
--- a/arch/arm/mach-s3c2440/mach-smdk2440.c
+++ b/arch/arm/mach-s3c2440/mach-smdk2440.c
@@ -175,7 +175,7 @@
 
 MACHINE_START(S3C2440, "SMDK2440")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 
 	.init_irq	= s3c24xx_init_irq,
 	.map_io		= smdk2440_map_io,
diff --git a/arch/arm/mach-s3c2443/mach-smdk2443.c b/arch/arm/mach-s3c2443/mach-smdk2443.c
index 514275e..bec107e 100644
--- a/arch/arm/mach-s3c2443/mach-smdk2443.c
+++ b/arch/arm/mach-s3c2443/mach-smdk2443.c
@@ -139,7 +139,7 @@
 
 MACHINE_START(SMDK2443, "SMDK2443")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
-	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.atag_offset	= 0x100,
 
 	.init_irq	= s3c24xx_init_irq,
 	.map_io		= smdk2443_map_io,
diff --git a/arch/arm/mach-s3c64xx/cpu.c b/arch/arm/mach-s3c64xx/cpu.c
index 374e45e..8dc0576 100644
--- a/arch/arm/mach-s3c64xx/cpu.c
+++ b/arch/arm/mach-s3c64xx/cpu.c
@@ -20,6 +20,7 @@
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include <linux/dma-mapping.h>
 
 #include <mach/hardware.h>
 #include <mach/map.h>
@@ -145,6 +146,7 @@
 	/* initialise the io descriptors we need for initialisation */
 	iotable_init(s3c_iodesc, ARRAY_SIZE(s3c_iodesc));
 	iotable_init(mach_desc, size);
+	init_consistent_dma_size(SZ_8M);
 
 	idcode = __raw_readl(S3C_VA_SYS + 0x118);
 	if (!idcode) {
diff --git a/arch/arm/mach-s3c64xx/include/mach/debug-macro.S b/arch/arm/mach-s3c64xx/include/mach/debug-macro.S
index a29e705..c0c076a 100644
--- a/arch/arm/mach-s3c64xx/include/mach/debug-macro.S
+++ b/arch/arm/mach-s3c64xx/include/mach/debug-macro.S
@@ -21,7 +21,7 @@
 	 * aligned and add in the offset when we load the value here.
 	 */
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C_PA_UART
 		ldr	\rv, = (S3C_VA_UART + S3C_PA_UART & 0xfffff)
 #if CONFIG_DEBUG_S3C_UART != 0
diff --git a/arch/arm/mach-s3c64xx/include/mach/memory.h b/arch/arm/mach-s3c64xx/include/mach/memory.h
deleted file mode 100644
index 4760cda..0000000
--- a/arch/arm/mach-s3c64xx/include/mach/memory.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/* arch/arm/mach-s3c6400/include/mach/memory.h
- *
- * Copyright 2008 Openmoko, Inc.
- * Copyright 2008 Simtec Electronics
- *      Ben Dooks <ben@simtec.co.uk>
- *      http://armlinux.simtec.co.uk/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET     UL(0x50000000)
-
-#define CONSISTENT_DMA_SIZE	SZ_8M
-
-#endif
diff --git a/arch/arm/mach-s3c64xx/mach-anw6410.c b/arch/arm/mach-s3c64xx/mach-anw6410.c
index cb88643..d164a28 100644
--- a/arch/arm/mach-s3c64xx/mach-anw6410.c
+++ b/arch/arm/mach-s3c64xx/mach-anw6410.c
@@ -233,7 +233,7 @@
 
 MACHINE_START(ANW6410, "A&W6410")
 	/* Maintainer: Kwangwoo Lee <kwangwoo.lee@gmail.com> */
-	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= anw6410_map_io,
diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c
index af0c2fe..4c76e084 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410.c
@@ -766,7 +766,7 @@
 
 MACHINE_START(WLF_CRAGG_6410, "Wolfson Cragganmore 6410")
 	/* Maintainer: Mark Brown <broonie@opensource.wolfsonmicro.com> */
-	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= crag6410_map_io,
 	.init_machine	= crag6410_machine_init,
diff --git a/arch/arm/mach-s3c64xx/mach-hmt.c b/arch/arm/mach-s3c64xx/mach-hmt.c
index b3d93cc..19a0887 100644
--- a/arch/arm/mach-s3c64xx/mach-hmt.c
+++ b/arch/arm/mach-s3c64xx/mach-hmt.c
@@ -265,7 +265,7 @@
 
 MACHINE_START(HMT, "Airgoo-HMT")
 	/* Maintainer: Peter Korsgaard <jacmet@sunsite.dk> */
-	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= hmt_map_io,
 	.init_machine	= hmt_machine_init,
diff --git a/arch/arm/mach-s3c64xx/mach-mini6410.c b/arch/arm/mach-s3c64xx/mach-mini6410.c
index 527f49b..e91f63f 100644
--- a/arch/arm/mach-s3c64xx/mach-mini6410.c
+++ b/arch/arm/mach-s3c64xx/mach-mini6410.c
@@ -349,7 +349,7 @@
 
 MACHINE_START(MINI6410, "MINI6410")
 	/* Maintainer: Darius Augulis <augulis.darius@gmail.com> */
-	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= mini6410_map_io,
 	.init_machine	= mini6410_machine_init,
diff --git a/arch/arm/mach-s3c64xx/mach-ncp.c b/arch/arm/mach-s3c64xx/mach-ncp.c
index 01c6857..c30f2e5 100644
--- a/arch/arm/mach-s3c64xx/mach-ncp.c
+++ b/arch/arm/mach-s3c64xx/mach-ncp.c
@@ -97,7 +97,7 @@
 
 MACHINE_START(NCP, "NCP")
 	/* Maintainer: Samsung Electronics */
-	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= ncp_map_io,
 	.init_machine	= ncp_machine_init,
diff --git a/arch/arm/mach-s3c64xx/mach-real6410.c b/arch/arm/mach-s3c64xx/mach-real6410.c
index 95b04b1..10870cb 100644
--- a/arch/arm/mach-s3c64xx/mach-real6410.c
+++ b/arch/arm/mach-s3c64xx/mach-real6410.c
@@ -329,7 +329,7 @@
 
 MACHINE_START(REAL6410, "REAL6410")
 	/* Maintainer: Darius Augulis <augulis.darius@gmail.com> */
-	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= real6410_map_io,
diff --git a/arch/arm/mach-s3c64xx/mach-smartq5.c b/arch/arm/mach-s3c64xx/mach-smartq5.c
index 342e8df..cbb57de 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq5.c
+++ b/arch/arm/mach-s3c64xx/mach-smartq5.c
@@ -146,7 +146,7 @@
 
 MACHINE_START(SMARTQ5, "SmartQ 5")
 	/* Maintainer: Maurus Cuelenaere <mcuelenaere AT gmail DOT com> */
-	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= smartq_map_io,
 	.init_machine	= smartq5_machine_init,
diff --git a/arch/arm/mach-s3c64xx/mach-smartq7.c b/arch/arm/mach-s3c64xx/mach-smartq7.c
index 5796397..04f914b 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq7.c
+++ b/arch/arm/mach-s3c64xx/mach-smartq7.c
@@ -162,7 +162,7 @@
 
 MACHINE_START(SMARTQ7, "SmartQ 7")
 	/* Maintainer: Maurus Cuelenaere <mcuelenaere AT gmail DOT com> */
-	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= smartq_map_io,
 	.init_machine	= smartq7_machine_init,
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6400.c b/arch/arm/mach-s3c64xx/mach-smdk6400.c
index 3cca642..6fd5e95 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6400.c
+++ b/arch/arm/mach-s3c64xx/mach-smdk6400.c
@@ -85,7 +85,7 @@
 
 MACHINE_START(SMDK6400, "SMDK6400")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
-	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 
 	.init_irq	= s3c6400_init_irq,
 	.map_io		= smdk6400_map_io,
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6410.c b/arch/arm/mach-s3c64xx/mach-smdk6410.c
index a9f3183..7b66ede 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6410.c
+++ b/arch/arm/mach-s3c64xx/mach-smdk6410.c
@@ -703,7 +703,7 @@
 
 MACHINE_START(SMDK6410, "SMDK6410")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
-	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= smdk6410_map_io,
diff --git a/arch/arm/mach-s5p64x0/cpu.c b/arch/arm/mach-s5p64x0/cpu.c
index a5c0095..8a93854 100644
--- a/arch/arm/mach-s5p64x0/cpu.c
+++ b/arch/arm/mach-s5p64x0/cpu.c
@@ -20,6 +20,7 @@
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
 #include <linux/sched.h>
+#include <linux/dma-mapping.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -111,6 +112,7 @@
 
 	iotable_init(s5p64x0_iodesc, ARRAY_SIZE(s5p64x0_iodesc));
 	iotable_init(s5p6440_iodesc, ARRAY_SIZE(s5p6440_iodesc));
+	init_consistent_dma_size(SZ_8M);
 }
 
 void __init s5p6450_map_io(void)
@@ -120,6 +122,7 @@
 
 	iotable_init(s5p64x0_iodesc, ARRAY_SIZE(s5p64x0_iodesc));
 	iotable_init(s5p6450_iodesc, ARRAY_SIZE(s5p6450_iodesc));
+	init_consistent_dma_size(SZ_8M);
 }
 
 /*
diff --git a/arch/arm/mach-s5p64x0/include/mach/debug-macro.S b/arch/arm/mach-s5p64x0/include/mach/debug-macro.S
index 79b04e6..e80ba3c 100644
--- a/arch/arm/mach-s5p64x0/include/mach/debug-macro.S
+++ b/arch/arm/mach-s5p64x0/include/mach/debug-macro.S
@@ -15,7 +15,7 @@
 
 #include <plat/regs-serial.h>
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		mov	\rp, #0xE0000000
 		orr	\rp, \rp, #0x00100000
 		ldr	\rp, [\rp, #0x118 ]
diff --git a/arch/arm/mach-s5p64x0/include/mach/memory.h b/arch/arm/mach-s5p64x0/include/mach/memory.h
deleted file mode 100644
index 365a6eb..0000000
--- a/arch/arm/mach-s5p64x0/include/mach/memory.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/* linux/arch/arm/mach-s5p64x0/include/mach/memory.h
- *
- * Copyright (c) 2009-2010 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- *
- * S5P64X0 - Memory definitions
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H __FILE__
-
-#define PLAT_PHYS_OFFSET		UL(0x20000000)
-#define CONSISTENT_DMA_SIZE	SZ_8M
-
-#endif /* __ASM_ARCH_MEMORY_H */
diff --git a/arch/arm/mach-s5p64x0/mach-smdk6440.c b/arch/arm/mach-s5p64x0/mach-smdk6440.c
index 346f8df..3b84e9b 100644
--- a/arch/arm/mach-s5p64x0/mach-smdk6440.c
+++ b/arch/arm/mach-s5p64x0/mach-smdk6440.c
@@ -171,7 +171,7 @@
 
 MACHINE_START(SMDK6440, "SMDK6440")
 	/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
-	.boot_params	= S5P64X0_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 
 	.init_irq	= s5p6440_init_irq,
 	.map_io		= smdk6440_map_io,
diff --git a/arch/arm/mach-s5p64x0/mach-smdk6450.c b/arch/arm/mach-s5p64x0/mach-smdk6450.c
index 33f2adf..d99d29b 100644
--- a/arch/arm/mach-s5p64x0/mach-smdk6450.c
+++ b/arch/arm/mach-s5p64x0/mach-smdk6450.c
@@ -190,7 +190,7 @@
 
 MACHINE_START(SMDK6450, "SMDK6450")
 	/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
-	.boot_params	= S5P64X0_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 
 	.init_irq	= s5p6450_init_irq,
 	.map_io		= smdk6450_map_io,
diff --git a/arch/arm/mach-s5pc100/include/mach/debug-macro.S b/arch/arm/mach-s5pc100/include/mach/debug-macro.S
index b2ba95d..694f759 100644
--- a/arch/arm/mach-s5pc100/include/mach/debug-macro.S
+++ b/arch/arm/mach-s5pc100/include/mach/debug-macro.S
@@ -22,7 +22,7 @@
 	 * aligned and add in the offset when we load the value here.
 	 */
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C_PA_UART
 		ldr	\rv, = S3C_VA_UART
 #if CONFIG_DEBUG_S3C_UART != 0
diff --git a/arch/arm/mach-s5pc100/include/mach/memory.h b/arch/arm/mach-s5pc100/include/mach/memory.h
deleted file mode 100644
index bda4e79..0000000
--- a/arch/arm/mach-s5pc100/include/mach/memory.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/* arch/arm/mach-s5pc100/include/mach/memory.h
- *
- * Copyright 2008 Samsung Electronics Co.
- *      Byungho Min <bhmin@samsung.com>
- *
- * Based on mach-s3c6400/include/mach/memory.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET     	UL(0x20000000)
-
-#endif
diff --git a/arch/arm/mach-s5pc100/mach-smdkc100.c b/arch/arm/mach-s5pc100/mach-smdkc100.c
index 227d890..688f45b 100644
--- a/arch/arm/mach-s5pc100/mach-smdkc100.c
+++ b/arch/arm/mach-s5pc100/mach-smdkc100.c
@@ -254,7 +254,7 @@
 
 MACHINE_START(SMDKC100, "SMDKC100")
 	/* Maintainer: Byungho Min <bhmin@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s5pc100_init_irq,
 	.map_io		= smdkc100_map_io,
 	.init_machine	= smdkc100_machine_init,
diff --git a/arch/arm/mach-s5pv210/cpu.c b/arch/arm/mach-s5pv210/cpu.c
index 79907ec..9114572 100644
--- a/arch/arm/mach-s5pv210/cpu.c
+++ b/arch/arm/mach-s5pv210/cpu.c
@@ -20,6 +20,7 @@
 #include <linux/sysdev.h>
 #include <linux/platform_device.h>
 #include <linux/sched.h>
+#include <linux/dma-mapping.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -119,6 +120,7 @@
 void __init s5pv210_map_io(void)
 {
 	iotable_init(s5pv210_iodesc, ARRAY_SIZE(s5pv210_iodesc));
+	init_consistent_dma_size(14 << 20);
 
 	/* initialise device information early */
 	s5pv210_default_sdhci0();
diff --git a/arch/arm/mach-s5pv210/include/mach/debug-macro.S b/arch/arm/mach-s5pv210/include/mach/debug-macro.S
index 169fe65..79e5559 100644
--- a/arch/arm/mach-s5pv210/include/mach/debug-macro.S
+++ b/arch/arm/mach-s5pv210/include/mach/debug-macro.S
@@ -21,7 +21,7 @@
 	 * aligned and add in the offset when we load the value here.
 	 */
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C_PA_UART
 		ldr	\rv, = S3C_VA_UART
 #if CONFIG_DEBUG_S3C_UART != 0
diff --git a/arch/arm/mach-s5pv210/include/mach/memory.h b/arch/arm/mach-s5pv210/include/mach/memory.h
index 7b5fcf0..2d3cfa2 100644
--- a/arch/arm/mach-s5pv210/include/mach/memory.h
+++ b/arch/arm/mach-s5pv210/include/mach/memory.h
@@ -14,7 +14,6 @@
 #define __ASM_ARCH_MEMORY_H
 
 #define PLAT_PHYS_OFFSET		UL(0x20000000)
-#define CONSISTENT_DMA_SIZE	(SZ_8M + SZ_4M + SZ_2M)
 
 /*
  * Sparsemem support
diff --git a/arch/arm/mach-s5pv210/mach-aquila.c b/arch/arm/mach-s5pv210/mach-aquila.c
index 509627f..5811a96 100644
--- a/arch/arm/mach-s5pv210/mach-aquila.c
+++ b/arch/arm/mach-s5pv210/mach-aquila.c
@@ -678,7 +678,7 @@
 	/* Maintainers:
 	   Marek Szyprowski <m.szyprowski@samsung.com>
 	   Kyungmin Park <kyungmin.park@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s5pv210_init_irq,
 	.map_io		= aquila_map_io,
 	.init_machine	= aquila_machine_init,
diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-s5pv210/mach-goni.c
index 85c2d51..061cc7e 100644
--- a/arch/arm/mach-s5pv210/mach-goni.c
+++ b/arch/arm/mach-s5pv210/mach-goni.c
@@ -897,7 +897,7 @@
 
 MACHINE_START(GONI, "GONI")
 	/* Maintainers: Kyungmin Park <kyungmin.park@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s5pv210_init_irq,
 	.map_io		= goni_map_io,
 	.init_machine	= goni_machine_init,
diff --git a/arch/arm/mach-s5pv210/mach-smdkc110.c b/arch/arm/mach-s5pv210/mach-smdkc110.c
index 6c412c8..f7266bb 100644
--- a/arch/arm/mach-s5pv210/mach-smdkc110.c
+++ b/arch/arm/mach-s5pv210/mach-smdkc110.c
@@ -136,7 +136,7 @@
 
 MACHINE_START(SMDKC110, "SMDKC110")
 	/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s5pv210_init_irq,
 	.map_io		= smdkc110_map_io,
 	.init_machine	= smdkc110_machine_init,
diff --git a/arch/arm/mach-s5pv210/mach-smdkv210.c b/arch/arm/mach-s5pv210/mach-smdkv210.c
index 5e011fc..e73e3b6d 100644
--- a/arch/arm/mach-s5pv210/mach-smdkv210.c
+++ b/arch/arm/mach-s5pv210/mach-smdkv210.c
@@ -319,7 +319,7 @@
 
 MACHINE_START(SMDKV210, "SMDKV210")
 	/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s5pv210_init_irq,
 	.map_io		= smdkv210_map_io,
 	.init_machine	= smdkv210_machine_init,
diff --git a/arch/arm/mach-s5pv210/mach-torbreck.c b/arch/arm/mach-s5pv210/mach-torbreck.c
index 925fc0d..97cc066 100644
--- a/arch/arm/mach-s5pv210/mach-torbreck.c
+++ b/arch/arm/mach-s5pv210/mach-torbreck.c
@@ -125,7 +125,7 @@
 
 MACHINE_START(TORBRECK, "TORBRECK")
 	/* Maintainer: Hyunchul Ko <ghcstop@gmail.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= s5pv210_init_irq,
 	.map_io		= torbreck_map_io,
 	.init_machine	= torbreck_machine_init,
diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c
index 26257df..d40da5f 100644
--- a/arch/arm/mach-sa1100/assabet.c
+++ b/arch/arm/mach-sa1100/assabet.c
@@ -447,7 +447,7 @@
 
 
 MACHINE_START(ASSABET, "Intel-Assabet")
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.fixup		= fixup_assabet,
 	.map_io		= assabet_map_io,
 	.init_irq	= sa1100_init_irq,
diff --git a/arch/arm/mach-sa1100/badge4.c b/arch/arm/mach-sa1100/badge4.c
index b4311b0..bda83e1 100644
--- a/arch/arm/mach-sa1100/badge4.c
+++ b/arch/arm/mach-sa1100/badge4.c
@@ -302,7 +302,7 @@
 }
 
 MACHINE_START(BADGE4, "Hewlett-Packard Laboratories BadgePAD 4")
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= badge4_map_io,
 	.init_irq	= sa1100_init_irq,
 	.timer		= &sa1100_timer,
diff --git a/arch/arm/mach-sa1100/h3100.c b/arch/arm/mach-sa1100/h3100.c
index 03d7376..b30733a 100644
--- a/arch/arm/mach-sa1100/h3100.c
+++ b/arch/arm/mach-sa1100/h3100.c
@@ -84,7 +84,7 @@
 }
 
 MACHINE_START(H3100, "Compaq iPAQ H3100")
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= h3100_map_io,
 	.init_irq	= sa1100_init_irq,
 	.timer		= &sa1100_timer,
diff --git a/arch/arm/mach-sa1100/h3600.c b/arch/arm/mach-sa1100/h3600.c
index 965f64a..6fd324d 100644
--- a/arch/arm/mach-sa1100/h3600.c
+++ b/arch/arm/mach-sa1100/h3600.c
@@ -125,7 +125,7 @@
 }
 
 MACHINE_START(H3600, "Compaq iPAQ H3600")
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= h3600_map_io,
 	.init_irq	= sa1100_init_irq,
 	.timer		= &sa1100_timer,
diff --git a/arch/arm/mach-sa1100/hackkit.c b/arch/arm/mach-sa1100/hackkit.c
index db5e434..30f4a55 100644
--- a/arch/arm/mach-sa1100/hackkit.c
+++ b/arch/arm/mach-sa1100/hackkit.c
@@ -195,7 +195,7 @@
  */
 
 MACHINE_START(HACKKIT, "HackKit Cpu Board")
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= hackkit_map_io,
 	.init_irq	= sa1100_init_irq,
 	.timer		= &sa1100_timer,
diff --git a/arch/arm/mach-sa1100/include/mach/debug-macro.S b/arch/arm/mach-sa1100/include/mach/debug-macro.S
index 0cd0fc9..530772d 100644
--- a/arch/arm/mach-sa1100/include/mach/debug-macro.S
+++ b/arch/arm/mach-sa1100/include/mach/debug-macro.S
@@ -12,7 +12,7 @@
 */
 #include <mach/hardware.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mrc	p15, 0, \rp, c1, c0
 		tst	\rp, #1			@ MMU enabled?
 		moveq	\rp, #0x80000000	@ physical base address
diff --git a/arch/arm/mach-sa1100/jornada720.c b/arch/arm/mach-sa1100/jornada720.c
index 176c066..0bb520d 100644
--- a/arch/arm/mach-sa1100/jornada720.c
+++ b/arch/arm/mach-sa1100/jornada720.c
@@ -364,7 +364,7 @@
 
 MACHINE_START(JORNADA720, "HP Jornada 720")
 	/* Maintainer: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> */
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= jornada720_map_io,
 	.init_irq	= sa1100_init_irq,
 	.timer		= &sa1100_timer,
diff --git a/arch/arm/mach-sa1100/lart.c b/arch/arm/mach-sa1100/lart.c
index 7b9556b..5bc59d0 100644
--- a/arch/arm/mach-sa1100/lart.c
+++ b/arch/arm/mach-sa1100/lart.c
@@ -61,7 +61,7 @@
 }
 
 MACHINE_START(LART, "LART")
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= lart_map_io,
 	.init_irq	= sa1100_init_irq,
 	.init_machine	= lart_init,
diff --git a/arch/arm/mach-sa1100/nanoengine.c b/arch/arm/mach-sa1100/nanoengine.c
index 72087f0..032f388 100644
--- a/arch/arm/mach-sa1100/nanoengine.c
+++ b/arch/arm/mach-sa1100/nanoengine.c
@@ -111,7 +111,7 @@
 }
 
 MACHINE_START(NANOENGINE, "BSE nanoEngine")
-	.boot_params	= 0xc0000000,
+	.atag_offset	= 0x100,
 	.map_io		= nanoengine_map_io,
 	.init_irq	= sa1100_init_irq,
 	.timer		= &sa1100_timer,
diff --git a/arch/arm/mach-sa1100/shannon.c b/arch/arm/mach-sa1100/shannon.c
index 7917b24..1cccbf5 100644
--- a/arch/arm/mach-sa1100/shannon.c
+++ b/arch/arm/mach-sa1100/shannon.c
@@ -82,7 +82,7 @@
 }
 
 MACHINE_START(SHANNON, "Shannon (AKA: Tuxscreen)")
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= shannon_map_io,
 	.init_irq	= sa1100_init_irq,
 	.timer		= &sa1100_timer,
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index cfb7607..a1c2427 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -229,7 +229,7 @@
 
 MACHINE_START(SIMPAD, "Simpad")
 	/* Maintainer: Holger Freyther */
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= simpad_map_io,
 	.init_irq	= sa1100_init_irq,
 	.timer		= &sa1100_timer,
diff --git a/arch/arm/mach-shark/core.c b/arch/arm/mach-shark/core.c
index ac2873c..feda3ca 100644
--- a/arch/arm/mach-shark/core.c
+++ b/arch/arm/mach-shark/core.c
@@ -152,7 +152,7 @@
 
 MACHINE_START(SHARK, "Shark")
 	/* Maintainer: Alexander Schulz */
-	.boot_params	= 0x08003000,
+	.atag_offset	= 0x3000,
 	.map_io		= shark_map_io,
 	.init_irq	= shark_init_irq,
 	.timer		= &shark_timer,
diff --git a/arch/arm/mach-shark/include/mach/debug-macro.S b/arch/arm/mach-shark/include/mach/debug-macro.S
index a473f55..20eb2bf 100644
--- a/arch/arm/mach-shark/include/mach/debug-macro.S
+++ b/arch/arm/mach-shark/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0xe0000000
 		orr	\rp, \rp, #0x000003f8
 		mov	\rv, \rp
diff --git a/arch/arm/mach-shmobile/board-ag5evm.c b/arch/arm/mach-shmobile/board-ag5evm.c
index cdfdd62..5fde49d 100644
--- a/arch/arm/mach-shmobile/board-ag5evm.c
+++ b/arch/arm/mach-shmobile/board-ag5evm.c
@@ -37,6 +37,7 @@
 #include <linux/mmc/sh_mobile_sdhi.h>
 #include <linux/mfd/tmio.h>
 #include <linux/sh_clk.h>
+#include <linux/dma-mapping.h>
 #include <video/sh_mobile_lcdc.h>
 #include <video/sh_mipi_dsi.h>
 #include <sound/sh_fsi.h>
@@ -447,6 +448,8 @@
 static void __init ag5evm_map_io(void)
 {
 	iotable_init(ag5evm_io_desc, ARRAY_SIZE(ag5evm_io_desc));
+	/* DMA memory at 0xf6000000 - 0xffdfffff */
+	init_consistent_dma_size(158 << 20);
 
 	/* setup early devices and console here as well */
 	sh73a0_add_early_devices();
diff --git a/arch/arm/mach-shmobile/board-ap4evb.c b/arch/arm/mach-shmobile/board-ap4evb.c
index 523f608..b622d8d 100644
--- a/arch/arm/mach-shmobile/board-ap4evb.c
+++ b/arch/arm/mach-shmobile/board-ap4evb.c
@@ -42,6 +42,7 @@
 #include <linux/leds.h>
 #include <linux/input/sh_keysc.h>
 #include <linux/usb/r8a66597.h>
+#include <linux/dma-mapping.h>
 
 #include <media/sh_mobile_ceu.h>
 #include <media/sh_mobile_csi2.h>
@@ -1170,6 +1171,8 @@
 static void __init ap4evb_map_io(void)
 {
 	iotable_init(ap4evb_io_desc, ARRAY_SIZE(ap4evb_io_desc));
+	/* DMA memory at 0xf6000000 - 0xffdfffff */
+	init_consistent_dma_size(158 << 20);
 
 	/* setup early devices and console here as well */
 	sh7372_add_early_devices();
diff --git a/arch/arm/mach-shmobile/board-g3evm.c b/arch/arm/mach-shmobile/board-g3evm.c
index ef4613b..8b620bf 100644
--- a/arch/arm/mach-shmobile/board-g3evm.c
+++ b/arch/arm/mach-shmobile/board-g3evm.c
@@ -32,6 +32,7 @@
 #include <linux/gpio.h>
 #include <linux/input.h>
 #include <linux/input/sh_keysc.h>
+#include <linux/dma-mapping.h>
 #include <mach/sh7367.h>
 #include <mach/common.h>
 #include <asm/mach-types.h>
@@ -260,6 +261,8 @@
 static void __init g3evm_map_io(void)
 {
 	iotable_init(g3evm_io_desc, ARRAY_SIZE(g3evm_io_desc));
+	/* DMA memory at 0xf6000000 - 0xffdfffff */
+	init_consistent_dma_size(158 << 20);
 
 	/* setup early devices and console here as well */
 	sh7367_add_early_devices();
diff --git a/arch/arm/mach-shmobile/board-g4evm.c b/arch/arm/mach-shmobile/board-g4evm.c
index 8e3c555..7719ddc 100644
--- a/arch/arm/mach-shmobile/board-g4evm.c
+++ b/arch/arm/mach-shmobile/board-g4evm.c
@@ -33,6 +33,7 @@
 #include <linux/mmc/host.h>
 #include <linux/mmc/sh_mobile_sdhi.h>
 #include <linux/gpio.h>
+#include <linux/dma-mapping.h>
 #include <mach/sh7377.h>
 #include <mach/common.h>
 #include <asm/mach-types.h>
@@ -274,6 +275,8 @@
 static void __init g4evm_map_io(void)
 {
 	iotable_init(g4evm_io_desc, ARRAY_SIZE(g4evm_io_desc));
+	/* DMA memory at 0xf6000000 - 0xffdfffff */
+	init_consistent_dma_size(158 << 20);
 
 	/* setup early devices and console here as well */
 	sh7377_add_early_devices();
diff --git a/arch/arm/mach-shmobile/board-mackerel.c b/arch/arm/mach-shmobile/board-mackerel.c
index 17c19dc..de2253d 100644
--- a/arch/arm/mach-shmobile/board-mackerel.c
+++ b/arch/arm/mach-shmobile/board-mackerel.c
@@ -45,6 +45,7 @@
 #include <linux/tca6416_keypad.h>
 #include <linux/usb/r8a66597.h>
 #include <linux/usb/renesas_usbhs.h>
+#include <linux/dma-mapping.h>
 
 #include <video/sh_mobile_hdmi.h>
 #include <video/sh_mobile_lcdc.h>
@@ -1381,6 +1382,8 @@
 static void __init mackerel_map_io(void)
 {
 	iotable_init(mackerel_io_desc, ARRAY_SIZE(mackerel_io_desc));
+	/* DMA memory at 0xf6000000 - 0xffdfffff */
+	init_consistent_dma_size(158 << 20);
 
 	/* setup early devices and console here as well */
 	sh7372_add_early_devices();
diff --git a/arch/arm/mach-shmobile/entry-intc.S b/arch/arm/mach-shmobile/entry-intc.S
index cac0a7a..1a1c00c 100644
--- a/arch/arm/mach-shmobile/entry-intc.S
+++ b/arch/arm/mach-shmobile/entry-intc.S
@@ -51,7 +51,4 @@
 	.macro  test_for_ipi, irqnr, irqstat, base, tmp
 	.endm
 
-	.macro  test_for_ltirq, irqnr, irqstat, base, tmp
-	.endm
-
 	arch_irq_handler shmobile_handle_irq_intc
diff --git a/arch/arm/mach-shmobile/include/mach/entry-macro.S b/arch/arm/mach-shmobile/include/mach/entry-macro.S
index d791f10..8d4a416 100644
--- a/arch/arm/mach-shmobile/include/mach/entry-macro.S
+++ b/arch/arm/mach-shmobile/include/mach/entry-macro.S
@@ -27,8 +27,5 @@
 	.macro  test_for_ipi, irqnr, irqstat, base, tmp
 	.endm
 
-	.macro  test_for_ltirq, irqnr, irqstat, base, tmp
-	.endm
-
 	.macro  arch_ret_to_user, tmp1, tmp2
 	.endm
diff --git a/arch/arm/mach-shmobile/include/mach/memory.h b/arch/arm/mach-shmobile/include/mach/memory.h
index ad00c3c..0ffbe81 100644
--- a/arch/arm/mach-shmobile/include/mach/memory.h
+++ b/arch/arm/mach-shmobile/include/mach/memory.h
@@ -4,7 +4,4 @@
 #define PLAT_PHYS_OFFSET	UL(CONFIG_MEMORY_START)
 #define MEM_SIZE	UL(CONFIG_MEMORY_SIZE)
 
-/* DMA memory at 0xf6000000 - 0xffdfffff */
-#define CONSISTENT_DMA_SIZE (158 << 20)
-
 #endif /* __ASM_MACH_MEMORY_H */
diff --git a/arch/arm/mach-shmobile/platsmp.c b/arch/arm/mach-shmobile/platsmp.c
index 66f9806..e4e485f 100644
--- a/arch/arm/mach-shmobile/platsmp.c
+++ b/arch/arm/mach-shmobile/platsmp.c
@@ -56,6 +56,12 @@
 	unsigned int ncores = shmobile_smp_get_core_count();
 	unsigned int i;
 
+	if (ncores > nr_cpu_ids) {
+		pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+			ncores, nr_cpu_ids);
+		ncores = nr_cpu_ids;
+	}
+
 	for (i = 0; i < ncores; i++)
 		set_cpu_possible(i, true);
 
diff --git a/arch/arm/mach-spear3xx/include/mach/memory.h b/arch/arm/mach-spear3xx/include/mach/memory.h
deleted file mode 100644
index 5173522..0000000
--- a/arch/arm/mach-spear3xx/include/mach/memory.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-spear3xx/include/mach/memory.h
- *
- * Memory map for SPEAr3xx machine family
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_MEMORY_H
-#define __MACH_MEMORY_H
-
-#include <plat/memory.h>
-
-#endif /* __MACH_MEMORY_H */
diff --git a/arch/arm/mach-spear3xx/spear300_evb.c b/arch/arm/mach-spear3xx/spear300_evb.c
index 69006f6..a5ff98e 100644
--- a/arch/arm/mach-spear3xx/spear300_evb.c
+++ b/arch/arm/mach-spear3xx/spear300_evb.c
@@ -64,7 +64,7 @@
 }
 
 MACHINE_START(SPEAR300, "ST-SPEAR300-EVB")
-	.boot_params	=	0x00000100,
+	.atag_offset	=	0x100,
 	.map_io		=	spear3xx_map_io,
 	.init_irq	=	spear3xx_init_irq,
 	.timer		=	&spear3xx_timer,
diff --git a/arch/arm/mach-spear3xx/spear310_evb.c b/arch/arm/mach-spear3xx/spear310_evb.c
index c8684ce..45d180d 100644
--- a/arch/arm/mach-spear3xx/spear310_evb.c
+++ b/arch/arm/mach-spear3xx/spear310_evb.c
@@ -70,7 +70,7 @@
 }
 
 MACHINE_START(SPEAR310, "ST-SPEAR310-EVB")
-	.boot_params	=	0x00000100,
+	.atag_offset	=	0x100,
 	.map_io		=	spear3xx_map_io,
 	.init_irq	=	spear3xx_init_irq,
 	.timer		=	&spear3xx_timer,
diff --git a/arch/arm/mach-spear3xx/spear320_evb.c b/arch/arm/mach-spear3xx/spear320_evb.c
index a12b353..2287984 100644
--- a/arch/arm/mach-spear3xx/spear320_evb.c
+++ b/arch/arm/mach-spear3xx/spear320_evb.c
@@ -68,7 +68,7 @@
 }
 
 MACHINE_START(SPEAR320, "ST-SPEAR320-EVB")
-	.boot_params	=	0x00000100,
+	.atag_offset	=	0x100,
 	.map_io		=	spear3xx_map_io,
 	.init_irq	=	spear3xx_init_irq,
 	.timer		=	&spear3xx_timer,
diff --git a/arch/arm/mach-spear6xx/include/mach/memory.h b/arch/arm/mach-spear6xx/include/mach/memory.h
deleted file mode 100644
index 781f088..0000000
--- a/arch/arm/mach-spear6xx/include/mach/memory.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-spear6xx/include/mach/memory.h
- *
- * Memory map for SPEAr6xx machine family
- *
- * Copyright (C) 2009 ST Microelectronics
- * Rajeev Kumar<rajeev-dlh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_MEMORY_H
-#define __MACH_MEMORY_H
-
-#include <plat/memory.h>
-
-#endif	/* __MACH_MEMORY_H */
diff --git a/arch/arm/mach-spear6xx/spear600_evb.c b/arch/arm/mach-spear6xx/spear600_evb.c
index f19cefe..8238fe3 100644
--- a/arch/arm/mach-spear6xx/spear600_evb.c
+++ b/arch/arm/mach-spear6xx/spear600_evb.c
@@ -43,7 +43,7 @@
 }
 
 MACHINE_START(SPEAR600, "ST-SPEAR600-EVB")
-	.boot_params	=	0x00000100,
+	.atag_offset	=	0x100,
 	.map_io		=	spear6xx_map_io,
 	.init_irq	=	spear6xx_init_irq,
 	.timer		=	&spear6xx_timer,
diff --git a/arch/arm/mach-tcc8k/board-tcc8000-sdk.c b/arch/arm/mach-tcc8k/board-tcc8000-sdk.c
index 4cb3c2d..777a5bb 100644
--- a/arch/arm/mach-tcc8k/board-tcc8000-sdk.c
+++ b/arch/arm/mach-tcc8k/board-tcc8000-sdk.c
@@ -73,7 +73,7 @@
 }
 
 MACHINE_START(TCC8000_SDK, "Telechips TCC8000-SDK Demo Board")
-	.boot_params	= PLAT_PHYS_OFFSET + 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= tcc8k_map_io,
 	.init_irq	= tcc8k_init_irq,
 	.init_machine	= tcc8k_init,
diff --git a/arch/arm/mach-tegra/board-harmony.c b/arch/arm/mach-tegra/board-harmony.c
index 846cd7d..a4d1980 100644
--- a/arch/arm/mach-tegra/board-harmony.c
+++ b/arch/arm/mach-tegra/board-harmony.c
@@ -179,7 +179,7 @@
 }
 
 MACHINE_START(HARMONY, "harmony")
-	.boot_params  = 0x00000100,
+	.atag_offset	= 0x100,
 	.fixup		= tegra_harmony_fixup,
 	.map_io         = tegra_map_common_io,
 	.init_early	= tegra_init_early,
diff --git a/arch/arm/mach-tegra/board-paz00.c b/arch/arm/mach-tegra/board-paz00.c
index ea2f79c..3197c4c 100644
--- a/arch/arm/mach-tegra/board-paz00.c
+++ b/arch/arm/mach-tegra/board-paz00.c
@@ -127,7 +127,7 @@
 }
 
 MACHINE_START(PAZ00, "Toshiba AC100 / Dynabook AZ")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.fixup		= tegra_paz00_fixup,
 	.map_io         = tegra_map_common_io,
 	.init_early	= tegra_init_early,
diff --git a/arch/arm/mach-tegra/board-seaboard.c b/arch/arm/mach-tegra/board-seaboard.c
index 56cbabf..9e98ac7 100644
--- a/arch/arm/mach-tegra/board-seaboard.c
+++ b/arch/arm/mach-tegra/board-seaboard.c
@@ -201,7 +201,7 @@
 
 
 MACHINE_START(SEABOARD, "seaboard")
-	.boot_params    = 0x00000100,
+	.atag_offset    = 0x100,
 	.map_io         = tegra_map_common_io,
 	.init_early     = tegra_init_early,
 	.init_irq       = tegra_init_irq,
@@ -210,7 +210,7 @@
 MACHINE_END
 
 MACHINE_START(KAEN, "kaen")
-	.boot_params    = 0x00000100,
+	.atag_offset    = 0x100,
 	.map_io         = tegra_map_common_io,
 	.init_early     = tegra_init_early,
 	.init_irq       = tegra_init_irq,
@@ -219,7 +219,7 @@
 MACHINE_END
 
 MACHINE_START(WARIO, "wario")
-	.boot_params    = 0x00000100,
+	.atag_offset    = 0x100,
 	.map_io         = tegra_map_common_io,
 	.init_early     = tegra_init_early,
 	.init_irq       = tegra_init_irq,
diff --git a/arch/arm/mach-tegra/board-trimslice.c b/arch/arm/mach-tegra/board-trimslice.c
index 89a6d2a..8489aa8 100644
--- a/arch/arm/mach-tegra/board-trimslice.c
+++ b/arch/arm/mach-tegra/board-trimslice.c
@@ -171,7 +171,7 @@
 }
 
 MACHINE_START(TRIMSLICE, "trimslice")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.fixup		= tegra_trimslice_fixup,
 	.map_io         = tegra_map_common_io,
 	.init_early	= tegra_init_early,
diff --git a/arch/arm/mach-tegra/include/mach/debug-macro.S b/arch/arm/mach-tegra/include/mach/debug-macro.S
index e0ebe65..619abc6 100644
--- a/arch/arm/mach-tegra/include/mach/debug-macro.S
+++ b/arch/arm/mach-tegra/include/mach/debug-macro.S
@@ -21,7 +21,7 @@
 #include <mach/io.h>
 #include <mach/iomap.h>
 
-	.macro  addruart, rp, rv
+	.macro  addruart, rp, rv, tmp
         ldr     \rp, =IO_APB_PHYS       @ physical
         ldr     \rv, =IO_APB_VIRT        @ virtual
 	orr	\rp, \rp, #(TEGRA_DEBUG_UART_BASE & 0xFF)
diff --git a/arch/arm/mach-tegra/include/mach/memory.h b/arch/arm/mach-tegra/include/mach/memory.h
deleted file mode 100644
index 537db3aa..0000000
--- a/arch/arm/mach-tegra/include/mach/memory.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * arch/arm/mach-tegra/include/mach/memory.h
- *
- * Copyright (C) 2010 Google, Inc.
- *
- * Author:
- *	Colin Cross <ccross@google.com>
- *	Erik Gilling <konkers@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __MACH_TEGRA_MEMORY_H
-#define __MACH_TEGRA_MEMORY_H
-
-/* physical offset of RAM */
-#define PLAT_PHYS_OFFSET		UL(0)
-
-#endif
-
diff --git a/arch/arm/mach-tegra/platsmp.c b/arch/arm/mach-tegra/platsmp.c
index 0886cbc..7d2b5d0 100644
--- a/arch/arm/mach-tegra/platsmp.c
+++ b/arch/arm/mach-tegra/platsmp.c
@@ -114,10 +114,10 @@
 {
 	unsigned int i, ncores = scu_get_core_count(scu_base);
 
-	if (ncores > NR_CPUS) {
-		printk(KERN_ERR "Tegra: no. of cores (%u) greater than configured (%u), clipping\n",
-			ncores, NR_CPUS);
-		ncores = NR_CPUS;
+	if (ncores > nr_cpu_ids) {
+		pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+			ncores, nr_cpu_ids);
+		ncores = nr_cpu_ids;
 	}
 
 	for (i = 0; i < ncores; i++)
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index 399c89f..376b6df 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -25,6 +25,7 @@
 #include <linux/err.h>
 #include <linux/mtd/nand.h>
 #include <linux/mtd/fsmc.h>
+#include <linux/dma-mapping.h>
 
 #include <asm/types.h>
 #include <asm/setup.h>
@@ -92,6 +93,8 @@
 void __init u300_map_io(void)
 {
 	iotable_init(u300_io_desc, ARRAY_SIZE(u300_io_desc));
+	/* We enable a real big DMA buffer if need be. */
+	init_consistent_dma_size(SZ_4M);
 }
 
 /*
diff --git a/arch/arm/mach-u300/include/mach/debug-macro.S b/arch/arm/mach-u300/include/mach/debug-macro.S
index df71570..8ae8e4a 100644
--- a/arch/arm/mach-u300/include/mach/debug-macro.S
+++ b/arch/arm/mach-u300/include/mach/debug-macro.S
@@ -10,7 +10,7 @@
  */
 #include <mach/hardware.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	/* If we move the address using MMU, use this. */
 	ldr	\rp,	  = U300_SLOW_PER_PHYS_BASE @ MMU off, physical address
 	ldr	\rv,	  = U300_SLOW_PER_VIRT_BASE @ MMU on, virtual address
diff --git a/arch/arm/mach-u300/include/mach/memory.h b/arch/arm/mach-u300/include/mach/memory.h
index 888e2e3..7034bae 100644
--- a/arch/arm/mach-u300/include/mach/memory.h
+++ b/arch/arm/mach-u300/include/mach/memory.h
@@ -16,7 +16,7 @@
 #ifdef CONFIG_MACH_U300_DUAL_RAM
 
 #define PLAT_PHYS_OFFSET		UL(0x48000000)
-#define BOOT_PARAMS_OFFSET	(PHYS_OFFSET + 0x100)
+#define BOOT_PARAMS_OFFSET		0x100
 
 #else
 
@@ -24,19 +24,14 @@
 #define PLAT_PHYS_OFFSET (0x28000000 + \
 	     (CONFIG_MACH_U300_ACCESS_MEM_SIZE - \
 	     (CONFIG_MACH_U300_ACCESS_MEM_SIZE & 1))*1024*1024)
+#define BOOT_PARAMS_OFFSET (0x100 + \
+	     (CONFIG_MACH_U300_ACCESS_MEM_SIZE & 1)*1024*1024*2)
 #else
 #define PLAT_PHYS_OFFSET (0x28000000 + \
 	     (CONFIG_MACH_U300_ACCESS_MEM_SIZE +	\
 	     (CONFIG_MACH_U300_ACCESS_MEM_SIZE & 1))*1024*1024)
+#define BOOT_PARAMS_OFFSET 0x100
 #endif
-#define BOOT_PARAMS_OFFSET (0x28000000 + \
-	    (CONFIG_MACH_U300_ACCESS_MEM_SIZE +		\
-	    (CONFIG_MACH_U300_ACCESS_MEM_SIZE & 1))*1024*1024 + 0x100)
 #endif
 
-/*
- * We enable a real big DMA buffer if need be.
- */
-#define CONSISTENT_DMA_SIZE SZ_4M
-
 #endif
diff --git a/arch/arm/mach-u300/u300.c b/arch/arm/mach-u300/u300.c
index 48b3b7f..80e7305 100644
--- a/arch/arm/mach-u300/u300.c
+++ b/arch/arm/mach-u300/u300.c
@@ -61,7 +61,7 @@
 
 MACHINE_START(U300, MACH_U300_STRING)
 	/* Maintainer: Linus Walleij <linus.walleij@stericsson.com> */
-	.boot_params	= BOOT_PARAMS_OFFSET,
+	.atag_offset	= BOOT_PARAMS_OFFSET,
 	.map_io		= u300_map_io,
 	.reserve	= u300_reserve,
 	.init_irq	= u300_init_irq,
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index cd54aba..2cc4876 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -645,7 +645,7 @@
 
 MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
 	/* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= u8500_map_io,
 	.init_irq	= ux500_init_irq,
 	/* we re-use nomadik timer here */
@@ -654,7 +654,7 @@
 MACHINE_END
 
 MACHINE_START(HREFV60, "ST-Ericsson U8500 Platform HREFv60+")
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= u8500_map_io,
 	.init_irq	= ux500_init_irq,
 	.timer		= &ux500_timer,
@@ -662,7 +662,7 @@
 MACHINE_END
 
 MACHINE_START(SNOWBALL, "Calao Systems Snowball platform")
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= u8500_map_io,
 	.init_irq	= ux500_init_irq,
 	/* we re-use nomadik timer here */
diff --git a/arch/arm/mach-ux500/board-u5500.c b/arch/arm/mach-ux500/board-u5500.c
index e58f0f5..166d47a 100644
--- a/arch/arm/mach-ux500/board-u5500.c
+++ b/arch/arm/mach-ux500/board-u5500.c
@@ -118,7 +118,7 @@
 }
 
 MACHINE_START(U5500, "ST-Ericsson U5500 Platform")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= u5500_map_io,
 	.init_irq	= ux500_init_irq,
 	.timer		= &ux500_timer,
diff --git a/arch/arm/mach-ux500/include/mach/debug-macro.S b/arch/arm/mach-ux500/include/mach/debug-macro.S
index 700fb05..8d74d92 100644
--- a/arch/arm/mach-ux500/include/mach/debug-macro.S
+++ b/arch/arm/mach-ux500/include/mach/debug-macro.S
@@ -35,7 +35,7 @@
 #define UX500_UART(n)	__UX500_UART(n)
 #define UART_BASE	UX500_UART(CONFIG_UX500_DEBUG_UART)
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =UART_BASE				@ no, physical address
 	ldr	\rv, =IO_ADDRESS(UART_BASE)		@ yes, virtual address
 	.endm
diff --git a/arch/arm/mach-ux500/include/mach/memory.h b/arch/arm/mach-ux500/include/mach/memory.h
deleted file mode 100644
index 2ef697a..0000000
--- a/arch/arm/mach-ux500/include/mach/memory.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/*
- * Copyright (C) 2009 ST-Ericsson
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET	UL(0x00000000)
-#define BUS_OFFSET	UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-ux500/platsmp.c b/arch/arm/mach-ux500/platsmp.c
index a33df5f..eb51991 100644
--- a/arch/arm/mach-ux500/platsmp.c
+++ b/arch/arm/mach-ux500/platsmp.c
@@ -156,12 +156,10 @@
 	ncores = scu_base ? scu_get_core_count(scu_base) : 1;
 
 	/* sanity check */
-	if (ncores > NR_CPUS) {
-		printk(KERN_WARNING
-		       "U8500: no. of cores (%d) greater than configured "
-		       "maximum of %d - clipping\n",
-		       ncores, NR_CPUS);
-		ncores = NR_CPUS;
+	if (ncores > nr_cpu_ids) {
+		pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+			ncores, nr_cpu_ids);
+		ncores = nr_cpu_ids;
 	}
 
 	for (i = 0; i < ncores; i++)
diff --git a/arch/arm/mach-versatile/include/mach/debug-macro.S b/arch/arm/mach-versatile/include/mach/debug-macro.S
index eb2cf7d..d0fbd7f 100644
--- a/arch/arm/mach-versatile/include/mach/debug-macro.S
+++ b/arch/arm/mach-versatile/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp,      #0x001F0000
 		orr	\rp, \rp, #0x00001000
 		orr	\rv, \rp, #0xf1000000	@ virtual base
diff --git a/arch/arm/mach-versatile/include/mach/memory.h b/arch/arm/mach-versatile/include/mach/memory.h
deleted file mode 100644
index dacc9d8..0000000
--- a/arch/arm/mach-versatile/include/mach/memory.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- *  arch/arm/mach-versatile/include/mach/memory.h
- *
- *  Copyright (C) 2003 ARM Limited
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET	UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-versatile/versatile_ab.c b/arch/arm/mach-versatile/versatile_ab.c
index f8ae64b..fda4866 100644
--- a/arch/arm/mach-versatile/versatile_ab.c
+++ b/arch/arm/mach-versatile/versatile_ab.c
@@ -35,7 +35,7 @@
 
 MACHINE_START(VERSATILE_AB, "ARM-Versatile AB")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= versatile_map_io,
 	.init_early	= versatile_init_early,
 	.init_irq	= versatile_init_irq,
diff --git a/arch/arm/mach-versatile/versatile_pb.c b/arch/arm/mach-versatile/versatile_pb.c
index 37c23df..feaf9cb 100644
--- a/arch/arm/mach-versatile/versatile_pb.c
+++ b/arch/arm/mach-versatile/versatile_pb.c
@@ -103,7 +103,7 @@
 
 MACHINE_START(VERSATILE_PB, "ARM-Versatile PB")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= versatile_map_io,
 	.init_early	= versatile_init_early,
 	.init_irq	= versatile_init_irq,
diff --git a/arch/arm/mach-vexpress/ct-ca9x4.c b/arch/arm/mach-vexpress/ct-ca9x4.c
index bfd32f5..2b1e836 100644
--- a/arch/arm/mach-vexpress/ct-ca9x4.c
+++ b/arch/arm/mach-vexpress/ct-ca9x4.c
@@ -221,6 +221,12 @@
 {
 	int i, ncores = scu_get_core_count(MMIO_P2V(A9_MPCORE_SCU));
 
+	if (ncores > nr_cpu_ids) {
+		pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+			ncores, nr_cpu_ids);
+		ncores = nr_cpu_ids;
+	}
+
 	for (i = 0; i < ncores; ++i)
 		set_cpu_possible(i, true);
 
diff --git a/arch/arm/mach-vexpress/include/mach/debug-macro.S b/arch/arm/mach-vexpress/include/mach/debug-macro.S
index 050d65e..fd9e6c7 100644
--- a/arch/arm/mach-vexpress/include/mach/debug-macro.S
+++ b/arch/arm/mach-vexpress/include/mach/debug-macro.S
@@ -12,7 +12,7 @@
 
 #define DEBUG_LL_UART_OFFSET	0x00009000
 
-		.macro	addruart,rp,rv
+		.macro	addruart,rp,rv,tmp
 		mov	\rp, #DEBUG_LL_UART_OFFSET
 		orr	\rv, \rp, #0xf8000000	@ virtual base
 		orr	\rp, \rp, #0x10000000	@ physical base
diff --git a/arch/arm/mach-vexpress/include/mach/memory.h b/arch/arm/mach-vexpress/include/mach/memory.h
deleted file mode 100644
index 5b7fcd4..0000000
--- a/arch/arm/mach-vexpress/include/mach/memory.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/*
- *  arch/arm/mach-vexpress/include/mach/memory.h
- *
- *  Copyright (C) 2003 ARM Limited
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET		UL(0x60000000)
-
-#endif
diff --git a/arch/arm/mach-vexpress/v2m.c b/arch/arm/mach-vexpress/v2m.c
index d0d267a..1fafc324 100644
--- a/arch/arm/mach-vexpress/v2m.c
+++ b/arch/arm/mach-vexpress/v2m.c
@@ -443,7 +443,7 @@
 }
 
 MACHINE_START(VEXPRESS, "ARM-Versatile Express")
-	.boot_params	= PLAT_PHYS_OFFSET + 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= v2m_map_io,
 	.init_early	= v2m_init_early,
 	.init_irq	= v2m_init_irq,
diff --git a/arch/arm/mach-vt8500/bv07.c b/arch/arm/mach-vt8500/bv07.c
index 94a261d..a464c75 100644
--- a/arch/arm/mach-vt8500/bv07.c
+++ b/arch/arm/mach-vt8500/bv07.c
@@ -68,7 +68,7 @@
 }
 
 MACHINE_START(BV07, "Benign BV07 Mini Netbook")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.reserve	= vt8500_reserve_mem,
 	.map_io		= vt8500_map_io,
 	.init_irq	= vt8500_init_irq,
diff --git a/arch/arm/mach-vt8500/include/mach/debug-macro.S b/arch/arm/mach-vt8500/include/mach/debug-macro.S
index f119162..ca292f2 100644
--- a/arch/arm/mach-vt8500/include/mach/debug-macro.S
+++ b/arch/arm/mach-vt8500/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  *
 */
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	mov	\rp,      #0x00200000
 	orr	\rv, \rp, #0xf8000000
 	orr	\rp, \rp, #0xd8000000
diff --git a/arch/arm/mach-vt8500/include/mach/memory.h b/arch/arm/mach-vt8500/include/mach/memory.h
deleted file mode 100644
index 175f914..0000000
--- a/arch/arm/mach-vt8500/include/mach/memory.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- *  arch/arm/mach-vt8500/include/mach/memory.h
- *
- *  Copyright (C) 2003 ARM Limited
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PHYS_OFFSET	UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-vt8500/wm8505_7in.c b/arch/arm/mach-vt8500/wm8505_7in.c
index e73aadb..cf910a9 100644
--- a/arch/arm/mach-vt8500/wm8505_7in.c
+++ b/arch/arm/mach-vt8500/wm8505_7in.c
@@ -68,7 +68,7 @@
 }
 
 MACHINE_START(WM8505_7IN_NETBOOK, "WM8505 7-inch generic netbook")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.reserve	= wm8505_reserve_mem,
 	.map_io		= wm8505_map_io,
 	.init_irq	= wm8505_init_irq,
diff --git a/arch/arm/mach-w90x900/include/mach/memory.h b/arch/arm/mach-w90x900/include/mach/memory.h
deleted file mode 100644
index f02905b..0000000
--- a/arch/arm/mach-w90x900/include/mach/memory.h
+++ /dev/null
@@ -1,23 +0,0 @@
-/*
- * arch/arm/mach-w90x900/include/mach/memory.h
- *
- * Copyright (c) 2008 Nuvoton technology corporation
- * All rights reserved.
- *
- * Wan ZongShun <mcuos.com@gmail.com>
- *
- * Based on arch/arm/mach-s3c2410/include/mach/memory.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET	UL(0x00000000)
-
-#endif
diff --git a/arch/arm/mach-w90x900/mach-nuc910evb.c b/arch/arm/mach-w90x900/mach-nuc910evb.c
index 30fccde..31c1090 100644
--- a/arch/arm/mach-w90x900/mach-nuc910evb.c
+++ b/arch/arm/mach-w90x900/mach-nuc910evb.c
@@ -34,7 +34,6 @@
 
 MACHINE_START(W90P910EVB, "W90P910EVB")
 	/* Maintainer: Wan ZongShun */
-	.boot_params	= 0,
 	.map_io		= nuc910evb_map_io,
 	.init_irq	= nuc900_init_irq,
 	.init_machine	= nuc910evb_init,
diff --git a/arch/arm/mach-w90x900/mach-nuc950evb.c b/arch/arm/mach-w90x900/mach-nuc950evb.c
index 590c99b..4062e55 100644
--- a/arch/arm/mach-w90x900/mach-nuc950evb.c
+++ b/arch/arm/mach-w90x900/mach-nuc950evb.c
@@ -37,7 +37,6 @@
 
 MACHINE_START(W90P950EVB, "W90P950EVB")
 	/* Maintainer: Wan ZongShun */
-	.boot_params	= 0,
 	.map_io		= nuc950evb_map_io,
 	.init_irq	= nuc900_init_irq,
 	.init_machine	= nuc950evb_init,
diff --git a/arch/arm/mach-w90x900/mach-nuc960evb.c b/arch/arm/mach-w90x900/mach-nuc960evb.c
index e09c645..0ab9995 100644
--- a/arch/arm/mach-w90x900/mach-nuc960evb.c
+++ b/arch/arm/mach-w90x900/mach-nuc960evb.c
@@ -34,7 +34,6 @@
 
 MACHINE_START(W90N960EVB, "W90N960EVB")
 	/* Maintainer: Wan ZongShun */
-	.boot_params	= 0,
 	.map_io		= nuc960evb_map_io,
 	.init_irq	= nuc900_init_irq,
 	.init_machine	= nuc960evb_init,
diff --git a/arch/arm/mach-zynq/include/mach/debug-macro.S b/arch/arm/mach-zynq/include/mach/debug-macro.S
index 9f664d5..3ab0be1 100644
--- a/arch/arm/mach-zynq/include/mach/debug-macro.S
+++ b/arch/arm/mach-zynq/include/mach/debug-macro.S
@@ -17,7 +17,7 @@
 #include <mach/zynq_soc.h>
 #include <mach/uart.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =LL_UART_PADDR	@ physical
 		ldr	\rv, =LL_UART_VADDR	@ virtual
 		.endm
diff --git a/arch/arm/mach-zynq/include/mach/memory.h b/arch/arm/mach-zynq/include/mach/memory.h
deleted file mode 100644
index 35a9263..0000000
--- a/arch/arm/mach-zynq/include/mach/memory.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/* arch/arm/mach-zynq/include/mach/memory.h
- *
- *  Copyright (C) 2011 Xilinx
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MACH_MEMORY_H__
-#define __MACH_MEMORY_H__
-
-#include <asm/sizes.h>
-
-#define PLAT_PHYS_OFFSET	UL(0x0)
-
-#endif
diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c
index c3ff82f..01f5987 100644
--- a/arch/arm/mm/dma-mapping.c
+++ b/arch/arm/mm/dma-mapping.c
@@ -18,12 +18,14 @@
 #include <linux/device.h>
 #include <linux/dma-mapping.h>
 #include <linux/highmem.h>
+#include <linux/slab.h>
 
 #include <asm/memory.h>
 #include <asm/highmem.h>
 #include <asm/cacheflush.h>
 #include <asm/tlbflush.h>
 #include <asm/sizes.h>
+#include <asm/mach/arch.h>
 
 #include "mm.h"
 
@@ -117,26 +119,37 @@
 }
 
 #ifdef CONFIG_MMU
-/* Sanity check size */
-#if (CONSISTENT_DMA_SIZE % SZ_2M)
-#error "CONSISTENT_DMA_SIZE must be multiple of 2MiB"
-#endif
 
-#define CONSISTENT_OFFSET(x)	(((unsigned long)(x) - CONSISTENT_BASE) >> PAGE_SHIFT)
-#define CONSISTENT_PTE_INDEX(x) (((unsigned long)(x) - CONSISTENT_BASE) >> PGDIR_SHIFT)
-#define NUM_CONSISTENT_PTES (CONSISTENT_DMA_SIZE >> PGDIR_SHIFT)
+
+#define CONSISTENT_OFFSET(x)	(((unsigned long)(x) - consistent_base) >> PAGE_SHIFT)
+#define CONSISTENT_PTE_INDEX(x) (((unsigned long)(x) - consistent_base) >> PGDIR_SHIFT)
 
 /*
  * These are the page tables (2MB each) covering uncached, DMA consistent allocations
  */
-static pte_t *consistent_pte[NUM_CONSISTENT_PTES];
+static pte_t **consistent_pte;
+
+#define DEFAULT_CONSISTENT_DMA_SIZE SZ_2M
+
+unsigned long consistent_base = CONSISTENT_END - DEFAULT_CONSISTENT_DMA_SIZE;
+
+void __init init_consistent_dma_size(unsigned long size)
+{
+	unsigned long base = CONSISTENT_END - ALIGN(size, SZ_2M);
+
+	BUG_ON(consistent_pte); /* Check we're called before DMA region init */
+	BUG_ON(base < VMALLOC_END);
+
+	/* Grow region to accommodate specified size  */
+	if (base < consistent_base)
+		consistent_base = base;
+}
 
 #include "vmregion.h"
 
 static struct arm_vmregion_head consistent_head = {
 	.vm_lock	= __SPIN_LOCK_UNLOCKED(&consistent_head.vm_lock),
 	.vm_list	= LIST_HEAD_INIT(consistent_head.vm_list),
-	.vm_start	= CONSISTENT_BASE,
 	.vm_end		= CONSISTENT_END,
 };
 
@@ -155,7 +168,17 @@
 	pmd_t *pmd;
 	pte_t *pte;
 	int i = 0;
-	u32 base = CONSISTENT_BASE;
+	unsigned long base = consistent_base;
+	unsigned long num_ptes = (CONSISTENT_END - base) >> PGDIR_SHIFT;
+
+	consistent_pte = kmalloc(num_ptes * sizeof(pte_t), GFP_KERNEL);
+	if (!consistent_pte) {
+		pr_err("%s: no memory\n", __func__);
+		return -ENOMEM;
+	}
+
+	pr_debug("DMA memory: 0x%08lx - 0x%08lx:\n", base, CONSISTENT_END);
+	consistent_head.vm_start = base;
 
 	do {
 		pgd = pgd_offset(&init_mm, base);
@@ -198,7 +221,7 @@
 	size_t align;
 	int bit;
 
-	if (!consistent_pte[0]) {
+	if (!consistent_pte) {
 		printk(KERN_ERR "%s: not initialised\n", __func__);
 		dump_stack();
 		return NULL;
diff --git a/arch/arm/mm/fault.c b/arch/arm/mm/fault.c
index 3b5ea68..aa33949 100644
--- a/arch/arm/mm/fault.c
+++ b/arch/arm/mm/fault.c
@@ -20,6 +20,7 @@
 #include <linux/highmem.h>
 #include <linux/perf_event.h>
 
+#include <asm/exception.h>
 #include <asm/system.h>
 #include <asm/pgtable.h>
 #include <asm/tlbflush.h>
diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c
index cc7e2d8..34409a0 100644
--- a/arch/arm/mm/init.c
+++ b/arch/arm/mm/init.c
@@ -653,9 +653,6 @@
 			"    ITCM    : 0x%08lx - 0x%08lx   (%4ld kB)\n"
 #endif
 			"    fixmap  : 0x%08lx - 0x%08lx   (%4ld kB)\n"
-#ifdef CONFIG_MMU
-			"    DMA     : 0x%08lx - 0x%08lx   (%4ld MB)\n"
-#endif
 			"    vmalloc : 0x%08lx - 0x%08lx   (%4ld MB)\n"
 			"    lowmem  : 0x%08lx - 0x%08lx   (%4ld MB)\n"
 #ifdef CONFIG_HIGHMEM
@@ -674,9 +671,6 @@
 			MLK(ITCM_OFFSET, (unsigned long) itcm_end),
 #endif
 			MLK(FIXADDR_START, FIXADDR_TOP),
-#ifdef CONFIG_MMU
-			MLM(CONSISTENT_BASE, CONSISTENT_END),
-#endif
 			MLM(VMALLOC_START, VMALLOC_END),
 			MLM(PAGE_OFFSET, (unsigned long)high_memory),
 #ifdef CONFIG_HIGHMEM
@@ -699,9 +693,6 @@
 	 * be detected at build time already.
 	 */
 #ifdef CONFIG_MMU
-	BUILD_BUG_ON(VMALLOC_END			> CONSISTENT_BASE);
-	BUG_ON(VMALLOC_END				> CONSISTENT_BASE);
-
 	BUILD_BUG_ON(TASK_SIZE				> MODULES_VADDR);
 	BUG_ON(TASK_SIZE 				> MODULES_VADDR);
 #endif
diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index 594d677..ea9c9f3 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -273,6 +273,14 @@
 		.prot_l1   = PMD_TYPE_TABLE,
 		.domain    = DOMAIN_KERNEL,
 	},
+	[MT_MEMORY_SO] = {
+		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
+				L_PTE_MT_UNCACHED,
+		.prot_l1   = PMD_TYPE_TABLE,
+		.prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_SECT_S |
+				PMD_SECT_UNCACHED | PMD_SECT_XN,
+		.domain    = DOMAIN_KERNEL,
+	},
 };
 
 const struct mem_type *get_mem_type(unsigned int type)
diff --git a/arch/arm/mm/proc-arm920.S b/arch/arm/mm/proc-arm920.S
index 2e6849b..88fb3d9 100644
--- a/arch/arm/mm/proc-arm920.S
+++ b/arch/arm/mm/proc-arm920.S
@@ -379,31 +379,26 @@
 
 /* Suspend/resume support: taken from arch/arm/plat-s3c24xx/sleep.S */
 .globl	cpu_arm920_suspend_size
-.equ	cpu_arm920_suspend_size, 4 * 4
+.equ	cpu_arm920_suspend_size, 4 * 3
 #ifdef CONFIG_PM_SLEEP
 ENTRY(cpu_arm920_do_suspend)
-	stmfd	sp!, {r4 - r7, lr}
+	stmfd	sp!, {r4 - r6, lr}
 	mrc	p15, 0, r4, c13, c0, 0	@ PID
 	mrc	p15, 0, r5, c3, c0, 0	@ Domain ID
-	mrc	p15, 0, r6, c2, c0, 0	@ TTB address
-	mrc	p15, 0, r7, c1, c0, 0	@ Control register
-	stmia	r0, {r4 - r7}
-	ldmfd	sp!, {r4 - r7, pc}
+	mrc	p15, 0, r6, c1, c0, 0	@ Control register
+	stmia	r0, {r4 - r6}
+	ldmfd	sp!, {r4 - r6, pc}
 ENDPROC(cpu_arm920_do_suspend)
 
 ENTRY(cpu_arm920_do_resume)
 	mov	ip, #0
 	mcr	p15, 0, ip, c8, c7, 0	@ invalidate I+D TLBs
 	mcr	p15, 0, ip, c7, c7, 0	@ invalidate I+D caches
-	ldmia	r0, {r4 - r7}
+	ldmia	r0, {r4 - r6}
 	mcr	p15, 0, r4, c13, c0, 0	@ PID
 	mcr	p15, 0, r5, c3, c0, 0	@ Domain ID
-	mcr	p15, 0, r6, c2, c0, 0	@ TTB address
-	mov	r0, r7			@ control register
-	mov	r2, r6, lsr #14		@ get TTB0 base
-	mov	r2, r2, lsl #14
-	ldr	r3, =PMD_TYPE_SECT | PMD_SECT_BUFFERABLE | \
-		     PMD_SECT_CACHEABLE | PMD_BIT4 | PMD_SECT_AP_WRITE
+	mcr	p15, 0, r1, c2, c0, 0	@ TTB address
+	mov	r0, r6			@ control register
 	b	cpu_resume_mmu
 ENDPROC(cpu_arm920_do_resume)
 #endif
diff --git a/arch/arm/mm/proc-arm926.S b/arch/arm/mm/proc-arm926.S
index cd8f79c..9f8fd91 100644
--- a/arch/arm/mm/proc-arm926.S
+++ b/arch/arm/mm/proc-arm926.S
@@ -394,31 +394,26 @@
 
 /* Suspend/resume support: taken from arch/arm/plat-s3c24xx/sleep.S */
 .globl	cpu_arm926_suspend_size
-.equ	cpu_arm926_suspend_size, 4 * 4
+.equ	cpu_arm926_suspend_size, 4 * 3
 #ifdef CONFIG_PM_SLEEP
 ENTRY(cpu_arm926_do_suspend)
-	stmfd	sp!, {r4 - r7, lr}
+	stmfd	sp!, {r4 - r6, lr}
 	mrc	p15, 0, r4, c13, c0, 0	@ PID
 	mrc	p15, 0, r5, c3, c0, 0	@ Domain ID
-	mrc	p15, 0, r6, c2, c0, 0	@ TTB address
-	mrc	p15, 0, r7, c1, c0, 0	@ Control register
-	stmia	r0, {r4 - r7}
-	ldmfd	sp!, {r4 - r7, pc}
+	mrc	p15, 0, r6, c1, c0, 0	@ Control register
+	stmia	r0, {r4 - r6}
+	ldmfd	sp!, {r4 - r6, pc}
 ENDPROC(cpu_arm926_do_suspend)
 
 ENTRY(cpu_arm926_do_resume)
 	mov	ip, #0
 	mcr	p15, 0, ip, c8, c7, 0	@ invalidate I+D TLBs
 	mcr	p15, 0, ip, c7, c7, 0	@ invalidate I+D caches
-	ldmia	r0, {r4 - r7}
+	ldmia	r0, {r4 - r6}
 	mcr	p15, 0, r4, c13, c0, 0	@ PID
 	mcr	p15, 0, r5, c3, c0, 0	@ Domain ID
-	mcr	p15, 0, r6, c2, c0, 0	@ TTB address
-	mov	r0, r7			@ control register
-	mov	r2, r6, lsr #14		@ get TTB0 base
-	mov	r2, r2, lsl #14
-	ldr	r3, =PMD_TYPE_SECT | PMD_SECT_BUFFERABLE | \
-		     PMD_SECT_CACHEABLE | PMD_BIT4 | PMD_SECT_AP_WRITE
+	mcr	p15, 0, r1, c2, c0, 0	@ TTB address
+	mov	r0, r6			@ control register
 	b	cpu_resume_mmu
 ENDPROC(cpu_arm926_do_resume)
 #endif
diff --git a/arch/arm/mm/proc-sa1100.S b/arch/arm/mm/proc-sa1100.S
index 69e7f2e..7d91545 100644
--- a/arch/arm/mm/proc-sa1100.S
+++ b/arch/arm/mm/proc-sa1100.S
@@ -168,20 +168,19 @@
 	mov	pc, lr
 
 .globl	cpu_sa1100_suspend_size
-.equ	cpu_sa1100_suspend_size, 4*4
+.equ	cpu_sa1100_suspend_size, 4 * 3
 #ifdef CONFIG_PM_SLEEP
 ENTRY(cpu_sa1100_do_suspend)
-	stmfd	sp!, {r4 - r7, lr}
+	stmfd	sp!, {r4 - r6, lr}
 	mrc	p15, 0, r4, c3, c0, 0		@ domain ID
-	mrc	p15, 0, r5, c2, c0, 0		@ translation table base addr
-	mrc	p15, 0, r6, c13, c0, 0		@ PID
-	mrc	p15, 0, r7, c1, c0, 0		@ control reg
-	stmia	r0, {r4 - r7}			@ store cp regs
-	ldmfd	sp!, {r4 - r7, pc}
+	mrc	p15, 0, r5, c13, c0, 0		@ PID
+	mrc	p15, 0, r6, c1, c0, 0		@ control reg
+	stmia	r0, {r4 - r6}			@ store cp regs
+	ldmfd	sp!, {r4 - r6, pc}
 ENDPROC(cpu_sa1100_do_suspend)
 
 ENTRY(cpu_sa1100_do_resume)
-	ldmia	r0, {r4 - r7}			@ load cp regs
+	ldmia	r0, {r4 - r6}			@ load cp regs
 	mov	ip, #0
 	mcr	p15, 0, ip, c8, c7, 0		@ flush I+D TLBs
 	mcr	p15, 0, ip, c7, c7, 0		@ flush I&D cache
@@ -189,13 +188,9 @@
 	mcr	p15, 0, ip, c9, c0, 5		@ allow user space to use RB
 
 	mcr	p15, 0, r4, c3, c0, 0		@ domain ID
-	mcr	p15, 0, r5, c2, c0, 0		@ translation table base addr
-	mcr	p15, 0, r6, c13, c0, 0		@ PID
-	mov	r0, r7				@ control register
-	mov	r2, r5, lsr #14			@ get TTB0 base
-	mov	r2, r2, lsl #14
-	ldr	r3, =PMD_TYPE_SECT | PMD_SECT_BUFFERABLE | \
-		     PMD_SECT_CACHEABLE | PMD_SECT_AP_WRITE
+	mcr	p15, 0, r1, c2, c0, 0		@ translation table base addr
+	mcr	p15, 0, r5, c13, c0, 0		@ PID
+	mov	r0, r6				@ control register
 	b	cpu_resume_mmu
 ENDPROC(cpu_sa1100_do_resume)
 #endif
diff --git a/arch/arm/mm/proc-v6.S b/arch/arm/mm/proc-v6.S
index a923aa0..d061d2f 100644
--- a/arch/arm/mm/proc-v6.S
+++ b/arch/arm/mm/proc-v6.S
@@ -128,20 +128,18 @@
 
 /* Suspend/resume support: taken from arch/arm/mach-s3c64xx/sleep.S */
 .globl	cpu_v6_suspend_size
-.equ	cpu_v6_suspend_size, 4 * 8
+.equ	cpu_v6_suspend_size, 4 * 6
 #ifdef CONFIG_PM_SLEEP
 ENTRY(cpu_v6_do_suspend)
-	stmfd	sp!, {r4 - r11, lr}
+	stmfd	sp!, {r4 - r9, lr}
 	mrc	p15, 0, r4, c13, c0, 0	@ FCSE/PID
-	mrc	p15, 0, r5, c13, c0, 1	@ Context ID
-	mrc	p15, 0, r6, c3, c0, 0	@ Domain ID
-	mrc	p15, 0, r7, c2, c0, 0	@ Translation table base 0
-	mrc	p15, 0, r8, c2, c0, 1	@ Translation table base 1
-	mrc	p15, 0, r9, c1, c0, 1	@ auxiliary control register
-	mrc	p15, 0, r10, c1, c0, 2	@ co-processor access control
-	mrc	p15, 0, r11, c1, c0, 0	@ control register
-	stmia	r0, {r4 - r11}
-	ldmfd	sp!, {r4- r11, pc}
+	mrc	p15, 0, r5, c3, c0, 0	@ Domain ID
+	mrc	p15, 0, r6, c2, c0, 1	@ Translation table base 1
+	mrc	p15, 0, r7, c1, c0, 1	@ auxiliary control register
+	mrc	p15, 0, r8, c1, c0, 2	@ co-processor access control
+	mrc	p15, 0, r9, c1, c0, 0	@ control register
+	stmia	r0, {r4 - r9}
+	ldmfd	sp!, {r4- r9, pc}
 ENDPROC(cpu_v6_do_suspend)
 
 ENTRY(cpu_v6_do_resume)
@@ -150,25 +148,21 @@
 	mcr	p15, 0, ip, c7, c5, 0	@ invalidate I cache
 	mcr	p15, 0, ip, c7, c15, 0	@ clean+invalidate cache
 	mcr	p15, 0, ip, c7, c10, 4	@ drain write buffer
-	ldmia	r0, {r4 - r11}
+	mcr	p15, 0, ip, c13, c0, 1	@ set reserved context ID
+	ldmia	r0, {r4 - r9}
 	mcr	p15, 0, r4, c13, c0, 0	@ FCSE/PID
-	mcr	p15, 0, r5, c13, c0, 1	@ Context ID
-	mcr	p15, 0, r6, c3, c0, 0	@ Domain ID
-	mcr	p15, 0, r7, c2, c0, 0	@ Translation table base 0
-	mcr	p15, 0, r8, c2, c0, 1	@ Translation table base 1
-	mcr	p15, 0, r9, c1, c0, 1	@ auxiliary control register
-	mcr	p15, 0, r10, c1, c0, 2	@ co-processor access control
+	mcr	p15, 0, r5, c3, c0, 0	@ Domain ID
+	ALT_SMP(orr	r1, r1, #TTB_FLAGS_SMP)
+	ALT_UP(orr	r1, r1, #TTB_FLAGS_UP)
+	mcr	p15, 0, r1, c2, c0, 0	@ Translation table base 0
+	mcr	p15, 0, r6, c2, c0, 1	@ Translation table base 1
+	mcr	p15, 0, r7, c1, c0, 1	@ auxiliary control register
+	mcr	p15, 0, r8, c1, c0, 2	@ co-processor access control
 	mcr	p15, 0, ip, c2, c0, 2	@ TTB control register
 	mcr	p15, 0, ip, c7, c5, 4	@ ISB
-	mov	r0, r11			@ control register
-	mov	r2, r7, lsr #14		@ get TTB0 base
-	mov	r2, r2, lsl #14
-	ldr	r3, cpu_resume_l1_flags
+	mov	r0, r9			@ control register
 	b	cpu_resume_mmu
 ENDPROC(cpu_v6_do_resume)
-cpu_resume_l1_flags:
-	ALT_SMP(.long PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_FLAGS_SMP)
-	ALT_UP(.long  PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_FLAGS_UP)
 #endif
 
 	string	cpu_v6_name, "ARMv6-compatible processor"
diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S
index 9049c0764..6af366c 100644
--- a/arch/arm/mm/proc-v7.S
+++ b/arch/arm/mm/proc-v7.S
@@ -217,56 +217,50 @@
 
 /* Suspend/resume support: derived from arch/arm/mach-s5pv210/sleep.S */
 .globl	cpu_v7_suspend_size
-.equ	cpu_v7_suspend_size, 4 * 9
+.equ	cpu_v7_suspend_size, 4 * 7
 #ifdef CONFIG_PM_SLEEP
 ENTRY(cpu_v7_do_suspend)
-	stmfd	sp!, {r4 - r11, lr}
+	stmfd	sp!, {r4 - r10, lr}
 	mrc	p15, 0, r4, c13, c0, 0	@ FCSE/PID
-	mrc	p15, 0, r5, c13, c0, 1	@ Context ID
-	mrc	p15, 0, r6, c13, c0, 3	@ User r/o thread ID
-	stmia	r0!, {r4 - r6}
+	mrc	p15, 0, r5, c13, c0, 3	@ User r/o thread ID
+	stmia	r0!, {r4 - r5}
 	mrc	p15, 0, r6, c3, c0, 0	@ Domain ID
-	mrc	p15, 0, r7, c2, c0, 0	@ TTB 0
-	mrc	p15, 0, r8, c2, c0, 1	@ TTB 1
-	mrc	p15, 0, r9, c1, c0, 0	@ Control register
-	mrc	p15, 0, r10, c1, c0, 1	@ Auxiliary control register
-	mrc	p15, 0, r11, c1, c0, 2	@ Co-processor access control
-	stmia	r0, {r6 - r11}
-	ldmfd	sp!, {r4 - r11, pc}
+	mrc	p15, 0, r7, c2, c0, 1	@ TTB 1
+	mrc	p15, 0, r8, c1, c0, 0	@ Control register
+	mrc	p15, 0, r9, c1, c0, 1	@ Auxiliary control register
+	mrc	p15, 0, r10, c1, c0, 2	@ Co-processor access control
+	stmia	r0, {r6 - r10}
+	ldmfd	sp!, {r4 - r10, pc}
 ENDPROC(cpu_v7_do_suspend)
 
 ENTRY(cpu_v7_do_resume)
 	mov	ip, #0
 	mcr	p15, 0, ip, c8, c7, 0	@ invalidate TLBs
 	mcr	p15, 0, ip, c7, c5, 0	@ invalidate I cache
-	ldmia	r0!, {r4 - r6}
+	mcr	p15, 0, ip, c13, c0, 1	@ set reserved context ID
+	ldmia	r0!, {r4 - r5}
 	mcr	p15, 0, r4, c13, c0, 0	@ FCSE/PID
-	mcr	p15, 0, r5, c13, c0, 1	@ Context ID
-	mcr	p15, 0, r6, c13, c0, 3	@ User r/o thread ID
-	ldmia	r0, {r6 - r11}
+	mcr	p15, 0, r5, c13, c0, 3	@ User r/o thread ID
+	ldmia	r0, {r6 - r10}
 	mcr	p15, 0, r6, c3, c0, 0	@ Domain ID
-	mcr	p15, 0, r7, c2, c0, 0	@ TTB 0
-	mcr	p15, 0, r8, c2, c0, 1	@ TTB 1
+	ALT_SMP(orr	r1, r1, #TTB_FLAGS_SMP)
+	ALT_UP(orr	r1, r1, #TTB_FLAGS_UP)
+	mcr	p15, 0, r1, c2, c0, 0	@ TTB 0
+	mcr	p15, 0, r7, c2, c0, 1	@ TTB 1
 	mcr	p15, 0, ip, c2, c0, 2	@ TTB control register
 	mrc	p15, 0, r4, c1, c0, 1	@ Read Auxiliary control register
-	teq	r4, r10			@ Is it already set?
-	mcrne	p15, 0, r10, c1, c0, 1	@ No, so write it
-	mcr	p15, 0, r11, c1, c0, 2	@ Co-processor access control
+	teq	r4, r9			@ Is it already set?
+	mcrne	p15, 0, r9, c1, c0, 1	@ No, so write it
+	mcr	p15, 0, r10, c1, c0, 2	@ Co-processor access control
 	ldr	r4, =PRRR		@ PRRR
 	ldr	r5, =NMRR		@ NMRR
 	mcr	p15, 0, r4, c10, c2, 0	@ write PRRR
 	mcr	p15, 0, r5, c10, c2, 1	@ write NMRR
 	isb
 	dsb
-	mov	r0, r9			@ control register
-	mov	r2, r7, lsr #14		@ get TTB0 base
-	mov	r2, r2, lsl #14
-	ldr	r3, cpu_resume_l1_flags
+	mov	r0, r8			@ control register
 	b	cpu_resume_mmu
 ENDPROC(cpu_v7_do_resume)
-cpu_resume_l1_flags:
-	ALT_SMP(.long PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_FLAGS_SMP)
-	ALT_UP(.long  PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_FLAGS_UP)
 #endif
 
 	__CPUINIT
diff --git a/arch/arm/mm/proc-xsc3.S b/arch/arm/mm/proc-xsc3.S
index 755e1bf..abf0507 100644
--- a/arch/arm/mm/proc-xsc3.S
+++ b/arch/arm/mm/proc-xsc3.S
@@ -406,24 +406,23 @@
 	.align
 
 .globl	cpu_xsc3_suspend_size
-.equ	cpu_xsc3_suspend_size, 4 * 7
+.equ	cpu_xsc3_suspend_size, 4 * 6
 #ifdef CONFIG_PM_SLEEP
 ENTRY(cpu_xsc3_do_suspend)
-	stmfd	sp!, {r4 - r10, lr}
+	stmfd	sp!, {r4 - r9, lr}
 	mrc	p14, 0, r4, c6, c0, 0	@ clock configuration, for turbo mode
 	mrc	p15, 0, r5, c15, c1, 0	@ CP access reg
 	mrc	p15, 0, r6, c13, c0, 0	@ PID
 	mrc 	p15, 0, r7, c3, c0, 0	@ domain ID
-	mrc 	p15, 0, r8, c2, c0, 0	@ translation table base addr
-	mrc	p15, 0, r9, c1, c0, 1	@ auxiliary control reg
-	mrc 	p15, 0, r10, c1, c0, 0	@ control reg
+	mrc	p15, 0, r8, c1, c0, 1	@ auxiliary control reg
+	mrc 	p15, 0, r9, c1, c0, 0	@ control reg
 	bic	r4, r4, #2		@ clear frequency change bit
-	stmia	r0, {r4 - r10}		@ store cp regs
-	ldmia	sp!, {r4 - r10, pc}
+	stmia	r0, {r4 - r9}		@ store cp regs
+	ldmia	sp!, {r4 - r9, pc}
 ENDPROC(cpu_xsc3_do_suspend)
 
 ENTRY(cpu_xsc3_do_resume)
-	ldmia	r0, {r4 - r10}		@ load cp regs
+	ldmia	r0, {r4 - r9}		@ load cp regs
 	mov	ip, #0
 	mcr	p15, 0, ip, c7, c7, 0	@ invalidate I & D caches, BTB
 	mcr	p15, 0, ip, c7, c10, 4	@ drain write (&fill) buffer
@@ -433,15 +432,10 @@
 	mcr	p15, 0, r5, c15, c1, 0	@ CP access reg
 	mcr	p15, 0, r6, c13, c0, 0	@ PID
 	mcr	p15, 0, r7, c3, c0, 0	@ domain ID
-	mcr	p15, 0, r8, c2, c0, 0	@ translation table base addr
-	mcr	p15, 0, r9, c1, c0, 1	@ auxiliary control reg
-
-	@ temporarily map resume_turn_on_mmu into the page table,
-	@ otherwise prefetch abort occurs after MMU is turned on
-	mov	r0, r10			@ control register
-	mov	r2, r8, lsr #14		@ get TTB0 base
-	mov	r2, r2, lsl #14
-	ldr	r3, =0x542e		@ section flags
+	orr	r1, r1, #0x18		@ cache the page table in L2
+	mcr	p15, 0, r1, c2, c0, 0	@ translation table base addr
+	mcr	p15, 0, r8, c1, c0, 1	@ auxiliary control reg
+	mov	r0, r9			@ control register
 	b	cpu_resume_mmu
 ENDPROC(cpu_xsc3_do_resume)
 #endif
diff --git a/arch/arm/mm/proc-xscale.S b/arch/arm/mm/proc-xscale.S
index fbc06e5..3277904 100644
--- a/arch/arm/mm/proc-xscale.S
+++ b/arch/arm/mm/proc-xscale.S
@@ -520,24 +520,23 @@
 	.align
 
 .globl	cpu_xscale_suspend_size
-.equ	cpu_xscale_suspend_size, 4 * 7
+.equ	cpu_xscale_suspend_size, 4 * 6
 #ifdef CONFIG_PM_SLEEP
 ENTRY(cpu_xscale_do_suspend)
-	stmfd	sp!, {r4 - r10, lr}
+	stmfd	sp!, {r4 - r9, lr}
 	mrc	p14, 0, r4, c6, c0, 0	@ clock configuration, for turbo mode
 	mrc	p15, 0, r5, c15, c1, 0	@ CP access reg
 	mrc	p15, 0, r6, c13, c0, 0	@ PID
 	mrc	p15, 0, r7, c3, c0, 0	@ domain ID
-	mrc	p15, 0, r8, c2, c0, 0	@ translation table base addr
-	mrc	p15, 0, r9, c1, c1, 0	@ auxiliary control reg
-	mrc	p15, 0, r10, c1, c0, 0	@ control reg
+	mrc	p15, 0, r8, c1, c1, 0	@ auxiliary control reg
+	mrc	p15, 0, r9, c1, c0, 0	@ control reg
 	bic	r4, r4, #2		@ clear frequency change bit
-	stmia	r0, {r4 - r10}		@ store cp regs
-	ldmfd	sp!, {r4 - r10, pc}
+	stmia	r0, {r4 - r9}		@ store cp regs
+	ldmfd	sp!, {r4 - r9, pc}
 ENDPROC(cpu_xscale_do_suspend)
 
 ENTRY(cpu_xscale_do_resume)
-	ldmia	r0, {r4 - r10}		@ load cp regs
+	ldmia	r0, {r4 - r9}		@ load cp regs
 	mov	ip, #0
 	mcr	p15, 0, ip, c8, c7, 0	@ invalidate I & D TLBs
 	mcr	p15, 0, ip, c7, c7, 0	@ invalidate I & D caches, BTB
@@ -545,13 +544,9 @@
 	mcr	p15, 0, r5, c15, c1, 0	@ CP access reg
 	mcr	p15, 0, r6, c13, c0, 0	@ PID
 	mcr	p15, 0, r7, c3, c0, 0	@ domain ID
-	mcr	p15, 0, r8, c2, c0, 0	@ translation table base addr
-	mcr	p15, 0, r9, c1, c1, 0	@ auxiliary control reg
-	mov	r0, r10			@ control register
-	mov	r2, r8, lsr #14		@ get TTB0 base
-	mov	r2, r2, lsl #14
-	ldr	r3, =PMD_TYPE_SECT | PMD_SECT_BUFFERABLE | \
-		     PMD_SECT_CACHEABLE | PMD_SECT_AP_WRITE
+	mcr	p15, 0, r1, c2, c0, 0	@ translation table base addr
+	mcr	p15, 0, r8, c1, c1, 0	@ auxiliary control reg
+	mov	r0, r9			@ control register
 	b	cpu_resume_mmu
 ENDPROC(cpu_xscale_do_resume)
 #endif
diff --git a/arch/arm/plat-mxc/include/mach/debug-macro.S b/arch/arm/plat-mxc/include/mach/debug-macro.S
index e4dde91..a304593 100644
--- a/arch/arm/plat-mxc/include/mach/debug-macro.S
+++ b/arch/arm/plat-mxc/include/mach/debug-macro.S
@@ -54,7 +54,7 @@
 
 #define UART_VADDR	IMX_IO_ADDRESS(UART_PADDR)
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =UART_PADDR	@ physical
 		ldr	\rv, =UART_VADDR	@ virtual
 		.endm
diff --git a/arch/arm/plat-mxc/include/mach/memory.h b/arch/arm/plat-mxc/include/mach/memory.h
deleted file mode 100644
index 35e6c7f..0000000
--- a/arch/arm/plat-mxc/include/mach/memory.h
+++ /dev/null
@@ -1,44 +0,0 @@
-/*
- * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-/*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_MXC_MEMORY_H__
-#define __ASM_ARCH_MXC_MEMORY_H__
-
-#define MX1_PHYS_OFFSET		UL(0x08000000)
-#define MX21_PHYS_OFFSET	UL(0xc0000000)
-#define MX25_PHYS_OFFSET	UL(0x80000000)
-#define MX27_PHYS_OFFSET	UL(0xa0000000)
-#define MX3x_PHYS_OFFSET	UL(0x80000000)
-#define MX50_PHYS_OFFSET	UL(0x70000000)
-#define MX51_PHYS_OFFSET	UL(0x90000000)
-#define MX53_PHYS_OFFSET	UL(0x70000000)
-
-#if !defined(CONFIG_RUNTIME_PHYS_OFFSET)
-# if defined CONFIG_ARCH_MX3
-#  define PLAT_PHYS_OFFSET		MX3x_PHYS_OFFSET
-# endif
-#endif
-
-#if defined(CONFIG_MX3_VIDEO)
-/*
- * Increase size of DMA-consistent memory region.
- * This is required for mx3 camera driver to capture at least two QXGA frames.
- */
-#define CONSISTENT_DMA_SIZE SZ_8M
-
-#elif defined(CONFIG_MX1_VIDEO) || defined(CONFIG_VIDEO_MX2_HOSTSUPPORT)
-/*
- * Increase size of DMA-consistent memory region.
- * This is required for i.MX camera driver to capture at least four VGA frames.
- */
-#define CONSISTENT_DMA_SIZE SZ_4M
-#endif /* CONFIG_MX1_VIDEO || CONFIG_VIDEO_MX2_HOSTSUPPORT */
-
-#endif /* __ASM_ARCH_MXC_MEMORY_H__ */
diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig
index bb8f4a6..95732af 100644
--- a/arch/arm/plat-omap/Kconfig
+++ b/arch/arm/plat-omap/Kconfig
@@ -14,6 +14,7 @@
 	select CLKDEV_LOOKUP
 	select CLKSRC_MMIO
 	select GENERIC_IRQ_CHIP
+	select NEED_MACH_MEMORY_H
 	help
 	  "Systems based on omap7xx, omap15xx or omap16xx"
 
diff --git a/arch/arm/plat-omap/include/plat/io.h b/arch/arm/plat-omap/include/plat/io.h
index d72ec85..ebe67ea 100644
--- a/arch/arm/plat-omap/include/plat/io.h
+++ b/arch/arm/plat-omap/include/plat/io.h
@@ -309,6 +309,8 @@
 void __iomem *omap_ioremap(unsigned long phys, size_t size, unsigned int type);
 void omap_iounmap(volatile void __iomem *addr);
 
+extern void __init omap_init_consistent_dma_size(void);
+
 #endif
 
 #endif
diff --git a/arch/arm/plat-omap/include/plat/memory.h b/arch/arm/plat-omap/include/plat/memory.h
deleted file mode 100644
index e6720aa..0000000
--- a/arch/arm/plat-omap/include/plat/memory.h
+++ /dev/null
@@ -1,102 +0,0 @@
-/*
- * arch/arm/plat-omap/include/mach/memory.h
- *
- * Memory map for OMAP-1510 and 1610
- *
- * Copyright (C) 2000 RidgeRun, Inc.
- * Author: Greg Lonnon <glonnon@ridgerun.com>
- *
- * This file was derived from arch/arm/mach-intergrator/include/mach/memory.h
- * Copyright (C) 1999 ARM Limited
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#if defined(CONFIG_ARCH_OMAP1)
-#define PLAT_PHYS_OFFSET		UL(0x10000000)
-#else
-#define PLAT_PHYS_OFFSET		UL(0x80000000)
-#endif
-
-/*
- * Bus address is physical address, except for OMAP-1510 Local Bus.
- * OMAP-1510 bus address is translated into a Local Bus address if the
- * OMAP bus type is lbus. We do the address translation based on the
- * device overriding the defaults used in the dma-mapping API.
- * Note that the is_lbus_device() test is not very efficient on 1510
- * because of the strncmp().
- */
-#ifdef CONFIG_ARCH_OMAP15XX
-
-/*
- * OMAP-1510 Local Bus address offset
- */
-#define OMAP1510_LB_OFFSET	UL(0x30000000)
-
-#define virt_to_lbus(x)		((x) - PAGE_OFFSET + OMAP1510_LB_OFFSET)
-#define lbus_to_virt(x)		((x) - OMAP1510_LB_OFFSET + PAGE_OFFSET)
-#define is_lbus_device(dev)	(cpu_is_omap15xx() && dev && (strncmp(dev_name(dev), "ohci", 4) == 0))
-
-#define __arch_pfn_to_dma(dev, pfn)	\
-	({ dma_addr_t __dma = __pfn_to_phys(pfn); \
-	   if (is_lbus_device(dev)) \
-		__dma = __dma - PHYS_OFFSET + OMAP1510_LB_OFFSET; \
-	   __dma; })
-
-#define __arch_dma_to_pfn(dev, addr)	\
-	({ dma_addr_t __dma = addr;				\
-	   if (is_lbus_device(dev))				\
-		__dma += PHYS_OFFSET - OMAP1510_LB_OFFSET;	\
-	   __phys_to_pfn(__dma);				\
-	})
-
-#define __arch_dma_to_virt(dev, addr)	({ (void *) (is_lbus_device(dev) ? \
-						lbus_to_virt(addr) : \
-						__phys_to_virt(addr)); })
-
-#define __arch_virt_to_dma(dev, addr)	({ unsigned long __addr = (unsigned long)(addr); \
-					   (dma_addr_t) (is_lbus_device(dev) ? \
-						virt_to_lbus(__addr) : \
-						__virt_to_phys(__addr)); })
-
-#endif	/* CONFIG_ARCH_OMAP15XX */
-
-/* Override the ARM default */
-#ifdef CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE
-
-#if (CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE == 0)
-#undef CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE
-#define CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE 2
-#endif
-
-#define CONSISTENT_DMA_SIZE \
-	(((CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE + 1) & ~1) * 1024 * 1024)
-
-#endif
-
-#endif
-
diff --git a/arch/arm/plat-omap/include/plat/serial.h b/arch/arm/plat-omap/include/plat/serial.h
index de3b10c..1ab9fd6 100644
--- a/arch/arm/plat-omap/include/plat/serial.h
+++ b/arch/arm/plat-omap/include/plat/serial.h
@@ -16,8 +16,8 @@
 #include <linux/init.h>
 
 /*
- * Memory entry used for the DEBUG_LL UART configuration. See also
- * uncompress.h and debug-macro.S.
+ * Memory entry used for the DEBUG_LL UART configuration, relative to
+ * start of RAM. See also uncompress.h and debug-macro.S.
  *
  * Note that using a memory location for storing the UART configuration
  * has at least two limitations:
@@ -27,7 +27,7 @@
  * 2. We assume printascii is called at least once before paging_init,
  *    and addruart has a chance to read OMAP_UART_INFO
  */
-#define OMAP_UART_INFO		(PLAT_PHYS_OFFSET + 0x3ffc)
+#define OMAP_UART_INFO_OFS	0x3ffc
 
 /* OMAP1 serial ports */
 #define OMAP1_UART1_BASE	0xfffb0000
diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h
index a067484..2f472e9 100644
--- a/arch/arm/plat-omap/include/plat/uncompress.h
+++ b/arch/arm/plat-omap/include/plat/uncompress.h
@@ -36,7 +36,13 @@
  */
 static void set_omap_uart_info(unsigned char port)
 {
-	*(volatile u32 *)OMAP_UART_INFO = port;
+	/*
+	 * Get address of some.bss variable and round it down
+	 * a la CONFIG_AUTO_ZRELADDR.
+	 */
+	u32 ram_start = (u32)&uart_shift & 0xf8000000;
+	u32 *uart_info = (u32 *)(ram_start + OMAP_UART_INFO_OFS);
+	*uart_info = port;
 }
 
 static void putc(int c)
diff --git a/arch/arm/plat-omap/io.c b/arch/arm/plat-omap/io.c
index f1ecfa9..e9b0e23 100644
--- a/arch/arm/plat-omap/io.c
+++ b/arch/arm/plat-omap/io.c
@@ -12,6 +12,7 @@
 #include <linux/module.h>
 #include <linux/io.h>
 #include <linux/mm.h>
+#include <linux/dma-mapping.h>
 
 #include <plat/omap7xx.h>
 #include <plat/omap1510.h>
@@ -139,3 +140,10 @@
 		__iounmap(addr);
 }
 EXPORT_SYMBOL(omap_iounmap);
+
+void __init omap_init_consistent_dma_size(void)
+{
+#ifdef CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE
+	init_consistent_dma_size(CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE << 20);
+#endif
+}
diff --git a/arch/arm/plat-spear/include/plat/debug-macro.S b/arch/arm/plat-spear/include/plat/debug-macro.S
index 8501bbf..02b160a 100644
--- a/arch/arm/plat-spear/include/plat/debug-macro.S
+++ b/arch/arm/plat-spear/include/plat/debug-macro.S
@@ -14,7 +14,7 @@
 #include <linux/amba/serial.h>
 #include <mach/hardware.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #SPEAR_DBG_UART_BASE		@ Physical base
 		mov	\rv, #VA_SPEAR_DBG_UART_BASE		@ Virtual base
 		.endm
diff --git a/arch/arm/plat-spear/include/plat/memory.h b/arch/arm/plat-spear/include/plat/memory.h
deleted file mode 100644
index 7e3599e..0000000
--- a/arch/arm/plat-spear/include/plat/memory.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/*
- * arch/arm/plat-spear/include/plat/memory.h
- *
- * Memory map for SPEAr platform
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __PLAT_MEMORY_H
-#define __PLAT_MEMORY_H
-
-/* Physical DRAM offset */
-#define PLAT_PHYS_OFFSET		UL(0x00000000)
-
-#endif /* __PLAT_MEMORY_H */
diff --git a/arch/arm/plat-tcc/include/mach/debug-macro.S b/arch/arm/plat-tcc/include/mach/debug-macro.S
index 7662f73..cf17d04 100644
--- a/arch/arm/plat-tcc/include/mach/debug-macro.S
+++ b/arch/arm/plat-tcc/include/mach/debug-macro.S
@@ -9,7 +9,7 @@
  *
  */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		moveq	\rp, #0x90000000	@ physical base address
 		movne	\rv, #0xF1000000	@ virtual base
 		orr	\rp, \rp, #0x00007000	@ UART0
diff --git a/arch/arm/plat-tcc/include/mach/memory.h b/arch/arm/plat-tcc/include/mach/memory.h
deleted file mode 100644
index 28a6e0c..0000000
--- a/arch/arm/plat-tcc/include/mach/memory.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/*
- * Copyright (C) 1999 ARM Limited
- * Copyright (C) 2000 RidgeRun, Inc.
- * Copyright (C) 2008-2009 Telechips
- * Copyright (C) 2010 Hans J. Koch <hjk@linutronix.de>
- *
- * Licensed under the terms of the GPL v2.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET		UL(0x20000000)
-
-#endif
diff --git a/arch/arm/vfp/vfpmodule.c b/arch/arm/vfp/vfpmodule.c
index 79bcb43..0cbd5a0 100644
--- a/arch/arm/vfp/vfpmodule.c
+++ b/arch/arm/vfp/vfpmodule.c
@@ -11,6 +11,7 @@
 #include <linux/module.h>
 #include <linux/types.h>
 #include <linux/cpu.h>
+#include <linux/cpu_pm.h>
 #include <linux/kernel.h>
 #include <linux/notifier.h>
 #include <linux/signal.h>
@@ -68,7 +69,7 @@
 /*
  * Force a reload of the VFP context from the thread structure.  We do
  * this by ensuring that access to the VFP hardware is disabled, and
- * clear last_VFP_context.  Must be called from non-preemptible context.
+ * clear vfp_current_hw_state.  Must be called from non-preemptible context.
  */
 static void vfp_force_reload(unsigned int cpu, struct thread_info *thread)
 {
@@ -436,9 +437,7 @@
 	set_copro_access(access | CPACC_FULL(10) | CPACC_FULL(11));
 }
 
-#ifdef CONFIG_PM
-#include <linux/syscore_ops.h>
-
+#ifdef CONFIG_CPU_PM
 static int vfp_pm_suspend(void)
 {
 	struct thread_info *ti = current_thread_info();
@@ -468,19 +467,33 @@
 	fmxr(FPEXC, fmrx(FPEXC) & ~FPEXC_EN);
 }
 
-static struct syscore_ops vfp_pm_syscore_ops = {
-	.suspend	= vfp_pm_suspend,
-	.resume		= vfp_pm_resume,
+static int vfp_cpu_pm_notifier(struct notifier_block *self, unsigned long cmd,
+	void *v)
+{
+	switch (cmd) {
+	case CPU_PM_ENTER:
+		vfp_pm_suspend();
+		break;
+	case CPU_PM_ENTER_FAILED:
+	case CPU_PM_EXIT:
+		vfp_pm_resume();
+		break;
+	}
+	return NOTIFY_OK;
+}
+
+static struct notifier_block vfp_cpu_pm_notifier_block = {
+	.notifier_call = vfp_cpu_pm_notifier,
 };
 
 static void vfp_pm_init(void)
 {
-	register_syscore_ops(&vfp_pm_syscore_ops);
+	cpu_pm_register_notifier(&vfp_cpu_pm_notifier_block);
 }
 
 #else
 static inline void vfp_pm_init(void) { }
-#endif /* CONFIG_PM */
+#endif /* CONFIG_CPU_PM */
 
 /*
  * Ensure that the VFP state stored in 'thread->vfpstate' is up to date
diff --git a/drivers/of/irq.c b/drivers/of/irq.c
index 9f689f1d..791270b 100644
--- a/drivers/of/irq.c
+++ b/drivers/of/irq.c
@@ -19,10 +19,12 @@
  */
 
 #include <linux/errno.h>
+#include <linux/list.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_irq.h>
 #include <linux/string.h>
+#include <linux/slab.h>
 
 /* For archs that don't support NO_IRQ (such as x86), provide a dummy value */
 #ifndef NO_IRQ
@@ -386,3 +388,108 @@
 
 	return i;
 }
+
+struct intc_desc {
+	struct list_head	list;
+	struct device_node	*dev;
+	struct device_node	*interrupt_parent;
+};
+
+/**
+ * of_irq_init - Scan and init matching interrupt controllers in DT
+ * @matches: 0 terminated array of nodes to match and init function to call
+ *
+ * This function scans the device tree for matching interrupt controller nodes,
+ * and calls their initialization functions in order with parents first.
+ */
+void __init of_irq_init(const struct of_device_id *matches)
+{
+	struct device_node *np, *parent = NULL;
+	struct intc_desc *desc, *temp_desc;
+	struct list_head intc_desc_list, intc_parent_list;
+
+	INIT_LIST_HEAD(&intc_desc_list);
+	INIT_LIST_HEAD(&intc_parent_list);
+
+	for_each_matching_node(np, matches) {
+		if (!of_find_property(np, "interrupt-controller", NULL))
+			continue;
+		/*
+		 * Here, we allocate and populate an intc_desc with the node
+		 * pointer, interrupt-parent device_node etc.
+		 */
+		desc = kzalloc(sizeof(*desc), GFP_KERNEL);
+		if (WARN_ON(!desc))
+			goto err;
+
+		desc->dev = np;
+		desc->interrupt_parent = of_irq_find_parent(np);
+		list_add_tail(&desc->list, &intc_desc_list);
+	}
+
+	/*
+	 * The root irq controller is the one without an interrupt-parent.
+	 * That one goes first, followed by the controllers that reference it,
+	 * followed by the ones that reference the 2nd level controllers, etc.
+	 */
+	while (!list_empty(&intc_desc_list)) {
+		/*
+		 * Process all controllers with the current 'parent'.
+		 * First pass will be looking for NULL as the parent.
+		 * The assumption is that NULL parent means a root controller.
+		 */
+		list_for_each_entry_safe(desc, temp_desc, &intc_desc_list, list) {
+			const struct of_device_id *match;
+			int ret;
+			of_irq_init_cb_t irq_init_cb;
+
+			if (desc->interrupt_parent != parent)
+				continue;
+
+			list_del(&desc->list);
+			match = of_match_node(matches, desc->dev);
+			if (WARN(!match->data,
+			    "of_irq_init: no init function for %s\n",
+			    match->compatible)) {
+				kfree(desc);
+				continue;
+			}
+
+			pr_debug("of_irq_init: init %s @ %p, parent %p\n",
+				 match->compatible,
+				 desc->dev, desc->interrupt_parent);
+			irq_init_cb = match->data;
+			ret = irq_init_cb(desc->dev, desc->interrupt_parent);
+			if (ret) {
+				kfree(desc);
+				continue;
+			}
+
+			/*
+			 * This one is now set up; add it to the parent list so
+			 * its children can get processed in a subsequent pass.
+			 */
+			list_add_tail(&desc->list, &intc_parent_list);
+		}
+
+		/* Get the next pending parent that might have children */
+		desc = list_first_entry(&intc_parent_list, typeof(*desc), list);
+		if (list_empty(&intc_parent_list) || !desc) {
+			pr_err("of_irq_init: children remain, but no parents\n");
+			break;
+		}
+		list_del(&desc->list);
+		parent = desc->dev;
+		kfree(desc);
+	}
+
+	list_for_each_entry_safe(desc, temp_desc, &intc_parent_list, list) {
+		list_del(&desc->list);
+		kfree(desc);
+	}
+err:
+	list_for_each_entry_safe(desc, temp_desc, &intc_desc_list, list) {
+		list_del(&desc->list);
+		kfree(desc);
+	}
+}
diff --git a/drivers/usb/musb/musb_debugfs.c b/drivers/usb/musb/musb_debugfs.c
index b0176e4..61f4ee4 100644
--- a/drivers/usb/musb/musb_debugfs.c
+++ b/drivers/usb/musb/musb_debugfs.c
@@ -41,12 +41,6 @@
 #include <linux/debugfs.h>
 #include <linux/seq_file.h>
 
-#ifdef	CONFIG_ARM
-#include <mach/hardware.h>
-#include <mach/memory.h>
-#include <asm/mach-types.h>
-#endif
-
 #include <asm/uaccess.h>
 
 #include "musb_core.h"
diff --git a/include/linux/cpu_pm.h b/include/linux/cpu_pm.h
new file mode 100644
index 0000000..455b233
--- /dev/null
+++ b/include/linux/cpu_pm.h
@@ -0,0 +1,109 @@
+/*
+ * Copyright (C) 2011 Google, Inc.
+ *
+ * Author:
+ *	Colin Cross <ccross@android.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef _LINUX_CPU_PM_H
+#define _LINUX_CPU_PM_H
+
+#include <linux/kernel.h>
+#include <linux/notifier.h>
+
+/*
+ * When a CPU goes to a low power state that turns off power to the CPU's
+ * power domain, the contents of some blocks (floating point coprocessors,
+ * interrupt controllers, caches, timers) in the same power domain can
+ * be lost.  The cpm_pm notifiers provide a method for platform idle, suspend,
+ * and hotplug implementations to notify the drivers for these blocks that
+ * they may be reset.
+ *
+ * All cpu_pm notifications must be called with interrupts disabled.
+ *
+ * The notifications are split into two classes: CPU notifications and CPU
+ * cluster notifications.
+ *
+ * CPU notifications apply to a single CPU and must be called on the affected
+ * CPU.  They are used to save per-cpu context for affected blocks.
+ *
+ * CPU cluster notifications apply to all CPUs in a single power domain. They
+ * are used to save any global context for affected blocks, and must be called
+ * after all the CPUs in the power domain have been notified of the low power
+ * state.
+ */
+
+/*
+ * Event codes passed as unsigned long val to notifier calls
+ */
+enum cpu_pm_event {
+	/* A single cpu is entering a low power state */
+	CPU_PM_ENTER,
+
+	/* A single cpu failed to enter a low power state */
+	CPU_PM_ENTER_FAILED,
+
+	/* A single cpu is exiting a low power state */
+	CPU_PM_EXIT,
+
+	/* A cpu power domain is entering a low power state */
+	CPU_CLUSTER_PM_ENTER,
+
+	/* A cpu power domain failed to enter a low power state */
+	CPU_CLUSTER_PM_ENTER_FAILED,
+
+	/* A cpu power domain is exiting a low power state */
+	CPU_CLUSTER_PM_EXIT,
+};
+
+#ifdef CONFIG_CPU_PM
+int cpu_pm_register_notifier(struct notifier_block *nb);
+int cpu_pm_unregister_notifier(struct notifier_block *nb);
+int cpu_pm_enter(void);
+int cpu_pm_exit(void);
+int cpu_cluster_pm_enter(void);
+int cpu_cluster_pm_exit(void);
+
+#else
+
+static inline int cpu_pm_register_notifier(struct notifier_block *nb)
+{
+	return 0;
+}
+
+static inline int cpu_pm_unregister_notifier(struct notifier_block *nb)
+{
+	return 0;
+}
+
+static inline int cpu_pm_enter(void)
+{
+	return 0;
+}
+
+static inline int cpu_pm_exit(void)
+{
+	return 0;
+}
+
+static inline int cpu_cluster_pm_enter(void)
+{
+	return 0;
+}
+
+static inline int cpu_cluster_pm_exit(void)
+{
+	return 0;
+}
+#endif
+#endif
diff --git a/include/linux/interrupt.h b/include/linux/interrupt.h
index a103732..664544f 100644
--- a/include/linux/interrupt.h
+++ b/include/linux/interrupt.h
@@ -95,6 +95,7 @@
  * @flags:	flags (see IRQF_* above)
  * @name:	name of the device
  * @dev_id:	cookie to identify the device
+ * @percpu_dev_id:	cookie to identify the device
  * @next:	pointer to the next irqaction for shared interrupts
  * @irq:	interrupt number
  * @dir:	pointer to the proc/irq/NN/name entry
@@ -104,17 +105,18 @@
  * @thread_mask:	bitmask for keeping track of @thread activity
  */
 struct irqaction {
-	irq_handler_t handler;
-	unsigned long flags;
-	void *dev_id;
-	struct irqaction *next;
-	int irq;
-	irq_handler_t thread_fn;
-	struct task_struct *thread;
-	unsigned long thread_flags;
-	unsigned long thread_mask;
-	const char *name;
-	struct proc_dir_entry *dir;
+	irq_handler_t		handler;
+	unsigned long		flags;
+	void			*dev_id;
+	void __percpu		*percpu_dev_id;
+	struct irqaction	*next;
+	int			irq;
+	irq_handler_t		thread_fn;
+	struct task_struct	*thread;
+	unsigned long		thread_flags;
+	unsigned long		thread_mask;
+	const char		*name;
+	struct proc_dir_entry	*dir;
 } ____cacheline_internodealigned_in_smp;
 
 extern irqreturn_t no_action(int cpl, void *dev_id);
@@ -136,6 +138,10 @@
 request_any_context_irq(unsigned int irq, irq_handler_t handler,
 			unsigned long flags, const char *name, void *dev_id);
 
+extern int __must_check
+request_percpu_irq(unsigned int irq, irq_handler_t handler,
+		   const char *devname, void __percpu *percpu_dev_id);
+
 extern void exit_irq_thread(void);
 #else
 
@@ -164,10 +170,18 @@
 	return request_irq(irq, handler, flags, name, dev_id);
 }
 
+static inline int __must_check
+request_percpu_irq(unsigned int irq, irq_handler_t handler,
+		   const char *devname, void __percpu *percpu_dev_id)
+{
+	return request_irq(irq, handler, 0, devname, percpu_dev_id);
+}
+
 static inline void exit_irq_thread(void) { }
 #endif
 
 extern void free_irq(unsigned int, void *);
+extern void free_percpu_irq(unsigned int, void __percpu *);
 
 struct device;
 
@@ -207,7 +221,9 @@
 
 extern void disable_irq_nosync(unsigned int irq);
 extern void disable_irq(unsigned int irq);
+extern void disable_percpu_irq(unsigned int irq);
 extern void enable_irq(unsigned int irq);
+extern void enable_percpu_irq(unsigned int irq, unsigned int type);
 
 /* The following three functions are for the core kernel use only. */
 #ifdef CONFIG_GENERIC_HARDIRQS
diff --git a/include/linux/irq.h b/include/linux/irq.h
index 5951730..59e49c8 100644
--- a/include/linux/irq.h
+++ b/include/linux/irq.h
@@ -66,6 +66,7 @@
  * IRQ_NO_BALANCING		- Interrupt cannot be balanced (affinity set)
  * IRQ_MOVE_PCNTXT		- Interrupt can be migrated from process context
  * IRQ_NESTED_TRHEAD		- Interrupt nests into another thread
+ * IRQ_PER_CPU_DEVID		- Dev_id is a per-cpu variable
  */
 enum {
 	IRQ_TYPE_NONE		= 0x00000000,
@@ -88,12 +89,13 @@
 	IRQ_MOVE_PCNTXT		= (1 << 14),
 	IRQ_NESTED_THREAD	= (1 << 15),
 	IRQ_NOTHREAD		= (1 << 16),
+	IRQ_PER_CPU_DEVID	= (1 << 17),
 };
 
 #define IRQF_MODIFY_MASK	\
 	(IRQ_TYPE_SENSE_MASK | IRQ_NOPROBE | IRQ_NOREQUEST | \
 	 IRQ_NOAUTOEN | IRQ_MOVE_PCNTXT | IRQ_LEVEL | IRQ_NO_BALANCING | \
-	 IRQ_PER_CPU | IRQ_NESTED_THREAD)
+	 IRQ_PER_CPU | IRQ_NESTED_THREAD | IRQ_NOTHREAD | IRQ_PER_CPU_DEVID)
 
 #define IRQ_NO_BALANCING_MASK	(IRQ_PER_CPU | IRQ_NO_BALANCING)
 
@@ -336,12 +338,14 @@
  * IRQCHIP_MASK_ON_SUSPEND:	Mask non wake irqs in the suspend path
  * IRQCHIP_ONOFFLINE_ENABLED:	Only call irq_on/off_line callbacks
  *				when irq enabled
+ * IRQCHIP_SKIP_SET_WAKE:	Skip chip.irq_set_wake(), for this irq chip
  */
 enum {
 	IRQCHIP_SET_TYPE_MASKED		= (1 <<  0),
 	IRQCHIP_EOI_IF_HANDLED		= (1 <<  1),
 	IRQCHIP_MASK_ON_SUSPEND		= (1 <<  2),
 	IRQCHIP_ONOFFLINE_ENABLED	= (1 <<  3),
+	IRQCHIP_SKIP_SET_WAKE		= (1 <<  4),
 };
 
 /* This include will go away once we isolated irq_desc usage to core code */
@@ -365,6 +369,8 @@
 struct irqaction;
 extern int setup_irq(unsigned int irq, struct irqaction *new);
 extern void remove_irq(unsigned int irq, struct irqaction *act);
+extern int setup_percpu_irq(unsigned int irq, struct irqaction *new);
+extern void remove_percpu_irq(unsigned int irq, struct irqaction *act);
 
 extern void irq_cpu_online(void);
 extern void irq_cpu_offline(void);
@@ -392,6 +398,7 @@
 extern void handle_edge_eoi_irq(unsigned int irq, struct irq_desc *desc);
 extern void handle_simple_irq(unsigned int irq, struct irq_desc *desc);
 extern void handle_percpu_irq(unsigned int irq, struct irq_desc *desc);
+extern void handle_percpu_devid_irq(unsigned int irq, struct irq_desc *desc);
 extern void handle_bad_irq(unsigned int irq, struct irq_desc *desc);
 extern void handle_nested_irq(unsigned int irq);
 
@@ -420,6 +427,8 @@
 	irq_set_chip_and_handler_name(irq, chip, handle, NULL);
 }
 
+extern int irq_set_percpu_devid(unsigned int irq);
+
 extern void
 __irq_set_handler(unsigned int irq, irq_flow_handler_t handle, int is_chained,
 		  const char *name);
@@ -481,6 +490,13 @@
 		irq_clear_status_flags(irq, IRQ_NESTED_THREAD);
 }
 
+static inline void irq_set_percpu_devid_flags(unsigned int irq)
+{
+	irq_set_status_flags(irq,
+			     IRQ_NOAUTOEN | IRQ_PER_CPU | IRQ_NOTHREAD |
+			     IRQ_NOPROBE | IRQ_PER_CPU_DEVID);
+}
+
 /* Handle dynamic irq creation and destruction */
 extern unsigned int create_irq_nr(unsigned int irq_want, int node);
 extern int create_irq(void);
diff --git a/include/linux/irqdesc.h b/include/linux/irqdesc.h
index 150134a..6b69c2c 100644
--- a/include/linux/irqdesc.h
+++ b/include/linux/irqdesc.h
@@ -53,6 +53,7 @@
 	unsigned long		last_unhandled;	/* Aging timer for unhandled count */
 	unsigned int		irqs_unhandled;
 	raw_spinlock_t		lock;
+	struct cpumask		*percpu_enabled;
 #ifdef CONFIG_SMP
 	const struct cpumask	*affinity_hint;
 	struct irq_affinity_notify *affinity_notify;
diff --git a/include/linux/irqdomain.h b/include/linux/irqdomain.h
index 3ad553e..99834e58 100644
--- a/include/linux/irqdomain.h
+++ b/include/linux/irqdomain.h
@@ -47,6 +47,7 @@
  *            of the irq_domain is responsible for allocating the array of
  *            irq_desc structures.
  * @nr_irq: Number of irqs managed by the irq domain
+ * @hwirq_base: Starting number for hwirqs managed by the irq domain
  * @ops: pointer to irq_domain methods
  * @priv: private data pointer for use by owner.  Not touched by irq_domain
  *        core code.
@@ -57,6 +58,7 @@
 	struct list_head list;
 	unsigned int irq_base;
 	unsigned int nr_irq;
+	unsigned int hwirq_base;
 	const struct irq_domain_ops *ops;
 	void *priv;
 	struct device_node *of_node;
@@ -72,9 +74,21 @@
 static inline unsigned int irq_domain_to_irq(struct irq_domain *d,
 					     unsigned long hwirq)
 {
-	return d->ops->to_irq ? d->ops->to_irq(d, hwirq) : d->irq_base + hwirq;
+	if (d->ops->to_irq)
+		return d->ops->to_irq(d, hwirq);
+	if (WARN_ON(hwirq < d->hwirq_base))
+		return 0;
+	return d->irq_base + hwirq - d->hwirq_base;
 }
 
+#define irq_domain_for_each_hwirq(d, hw) \
+	for (hw = d->hwirq_base; hw < d->hwirq_base + d->nr_irq; hw++)
+
+#define irq_domain_for_each_irq(d, hw, irq) \
+	for (hw = d->hwirq_base, irq = irq_domain_to_irq(d, hw); \
+	     hw < d->hwirq_base + d->nr_irq; \
+	     hw++, irq = irq_domain_to_irq(d, hw))
+
 extern void irq_domain_add(struct irq_domain *domain);
 extern void irq_domain_del(struct irq_domain *domain);
 #endif /* CONFIG_IRQ_DOMAIN */
diff --git a/include/linux/of_irq.h b/include/linux/of_irq.h
index cd2e61c..d0307ee 100644
--- a/include/linux/of_irq.h
+++ b/include/linux/of_irq.h
@@ -33,6 +33,8 @@
 	u32 specifier[OF_MAX_IRQ_SPEC]; /* Specifier copy */
 };
 
+typedef int (*of_irq_init_cb_t)(struct device_node *, struct device_node *);
+
 /*
  * Workarounds only applied to 32bit powermac machines
  */
@@ -73,6 +75,7 @@
 		struct resource *res, int nr_irqs);
 extern struct device_node *of_irq_find_parent(struct device_node *child);
 
+extern void of_irq_init(const struct of_device_id *matches);
 
 #endif /* CONFIG_OF_IRQ */
 #endif /* CONFIG_OF */
diff --git a/kernel/Makefile b/kernel/Makefile
index eca595e..988cb3d 100644
--- a/kernel/Makefile
+++ b/kernel/Makefile
@@ -101,6 +101,7 @@
 obj-$(CONFIG_TRACEPOINTS) += trace/
 obj-$(CONFIG_SMP) += sched_cpupri.o
 obj-$(CONFIG_IRQ_WORK) += irq_work.o
+obj-$(CONFIG_CPU_PM) += cpu_pm.o
 
 obj-$(CONFIG_PERF_EVENTS) += events/
 
diff --git a/kernel/cpu_pm.c b/kernel/cpu_pm.c
new file mode 100644
index 0000000..249152e
--- /dev/null
+++ b/kernel/cpu_pm.c
@@ -0,0 +1,233 @@
+/*
+ * Copyright (C) 2011 Google, Inc.
+ *
+ * Author:
+ *	Colin Cross <ccross@android.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/cpu_pm.h>
+#include <linux/module.h>
+#include <linux/notifier.h>
+#include <linux/spinlock.h>
+#include <linux/syscore_ops.h>
+
+static DEFINE_RWLOCK(cpu_pm_notifier_lock);
+static RAW_NOTIFIER_HEAD(cpu_pm_notifier_chain);
+
+static int cpu_pm_notify(enum cpu_pm_event event, int nr_to_call, int *nr_calls)
+{
+	int ret;
+
+	ret = __raw_notifier_call_chain(&cpu_pm_notifier_chain, event, NULL,
+		nr_to_call, nr_calls);
+
+	return notifier_to_errno(ret);
+}
+
+/**
+ * cpu_pm_register_notifier - register a driver with cpu_pm
+ * @nb: notifier block to register
+ *
+ * Add a driver to a list of drivers that are notified about
+ * CPU and CPU cluster low power entry and exit.
+ *
+ * This function may sleep, and has the same return conditions as
+ * raw_notifier_chain_register.
+ */
+int cpu_pm_register_notifier(struct notifier_block *nb)
+{
+	unsigned long flags;
+	int ret;
+
+	write_lock_irqsave(&cpu_pm_notifier_lock, flags);
+	ret = raw_notifier_chain_register(&cpu_pm_notifier_chain, nb);
+	write_unlock_irqrestore(&cpu_pm_notifier_lock, flags);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(cpu_pm_register_notifier);
+
+/**
+ * cpu_pm_unregister_notifier - unregister a driver with cpu_pm
+ * @nb: notifier block to be unregistered
+ *
+ * Remove a driver from the CPU PM notifier list.
+ *
+ * This function may sleep, and has the same return conditions as
+ * raw_notifier_chain_unregister.
+ */
+int cpu_pm_unregister_notifier(struct notifier_block *nb)
+{
+	unsigned long flags;
+	int ret;
+
+	write_lock_irqsave(&cpu_pm_notifier_lock, flags);
+	ret = raw_notifier_chain_unregister(&cpu_pm_notifier_chain, nb);
+	write_unlock_irqrestore(&cpu_pm_notifier_lock, flags);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(cpu_pm_unregister_notifier);
+
+/**
+ * cpm_pm_enter - CPU low power entry notifier
+ *
+ * Notifies listeners that a single CPU is entering a low power state that may
+ * cause some blocks in the same power domain as the cpu to reset.
+ *
+ * Must be called on the affected CPU with interrupts disabled.  Platform is
+ * responsible for ensuring that cpu_pm_enter is not called twice on the same
+ * CPU before cpu_pm_exit is called. Notified drivers can include VFP
+ * co-processor, interrupt controller and it's PM extensions, local CPU
+ * timers context save/restore which shouldn't be interrupted. Hence it
+ * must be called with interrupts disabled.
+ *
+ * Return conditions are same as __raw_notifier_call_chain.
+ */
+int cpu_pm_enter(void)
+{
+	int nr_calls;
+	int ret = 0;
+
+	read_lock(&cpu_pm_notifier_lock);
+	ret = cpu_pm_notify(CPU_PM_ENTER, -1, &nr_calls);
+	if (ret)
+		/*
+		 * Inform listeners (nr_calls - 1) about failure of CPU PM
+		 * PM entry who are notified earlier to prepare for it.
+		 */
+		cpu_pm_notify(CPU_PM_ENTER_FAILED, nr_calls - 1, NULL);
+	read_unlock(&cpu_pm_notifier_lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(cpu_pm_enter);
+
+/**
+ * cpm_pm_exit - CPU low power exit notifier
+ *
+ * Notifies listeners that a single CPU is exiting a low power state that may
+ * have caused some blocks in the same power domain as the cpu to reset.
+ *
+ * Notified drivers can include VFP co-processor, interrupt controller
+ * and it's PM extensions, local CPU timers context save/restore which
+ * shouldn't be interrupted. Hence it must be called with interrupts disabled.
+ *
+ * Return conditions are same as __raw_notifier_call_chain.
+ */
+int cpu_pm_exit(void)
+{
+	int ret;
+
+	read_lock(&cpu_pm_notifier_lock);
+	ret = cpu_pm_notify(CPU_PM_EXIT, -1, NULL);
+	read_unlock(&cpu_pm_notifier_lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(cpu_pm_exit);
+
+/**
+ * cpm_cluster_pm_enter - CPU cluster low power entry notifier
+ *
+ * Notifies listeners that all cpus in a power domain are entering a low power
+ * state that may cause some blocks in the same power domain to reset.
+ *
+ * Must be called after cpu_pm_enter has been called on all cpus in the power
+ * domain, and before cpu_pm_exit has been called on any cpu in the power
+ * domain. Notified drivers can include VFP co-processor, interrupt controller
+ * and it's PM extensions, local CPU timers context save/restore which
+ * shouldn't be interrupted. Hence it must be called with interrupts disabled.
+ *
+ * Must be called with interrupts disabled.
+ *
+ * Return conditions are same as __raw_notifier_call_chain.
+ */
+int cpu_cluster_pm_enter(void)
+{
+	int nr_calls;
+	int ret = 0;
+
+	read_lock(&cpu_pm_notifier_lock);
+	ret = cpu_pm_notify(CPU_CLUSTER_PM_ENTER, -1, &nr_calls);
+	if (ret)
+		/*
+		 * Inform listeners (nr_calls - 1) about failure of CPU cluster
+		 * PM entry who are notified earlier to prepare for it.
+		 */
+		cpu_pm_notify(CPU_CLUSTER_PM_ENTER_FAILED, nr_calls - 1, NULL);
+	read_unlock(&cpu_pm_notifier_lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(cpu_cluster_pm_enter);
+
+/**
+ * cpm_cluster_pm_exit - CPU cluster low power exit notifier
+ *
+ * Notifies listeners that all cpus in a power domain are exiting form a
+ * low power state that may have caused some blocks in the same power domain
+ * to reset.
+ *
+ * Must be called after cpu_pm_exit has been called on all cpus in the power
+ * domain, and before cpu_pm_exit has been called on any cpu in the power
+ * domain. Notified drivers can include VFP co-processor, interrupt controller
+ * and it's PM extensions, local CPU timers context save/restore which
+ * shouldn't be interrupted. Hence it must be called with interrupts disabled.
+ *
+ * Return conditions are same as __raw_notifier_call_chain.
+ */
+int cpu_cluster_pm_exit(void)
+{
+	int ret;
+
+	read_lock(&cpu_pm_notifier_lock);
+	ret = cpu_pm_notify(CPU_CLUSTER_PM_EXIT, -1, NULL);
+	read_unlock(&cpu_pm_notifier_lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(cpu_cluster_pm_exit);
+
+#ifdef CONFIG_PM
+static int cpu_pm_suspend(void)
+{
+	int ret;
+
+	ret = cpu_pm_enter();
+	if (ret)
+		return ret;
+
+	ret = cpu_cluster_pm_enter();
+	return ret;
+}
+
+static void cpu_pm_resume(void)
+{
+	cpu_cluster_pm_exit();
+	cpu_pm_exit();
+}
+
+static struct syscore_ops cpu_pm_syscore_ops = {
+	.suspend = cpu_pm_suspend,
+	.resume = cpu_pm_resume,
+};
+
+static int cpu_pm_init(void)
+{
+	register_syscore_ops(&cpu_pm_syscore_ops);
+	return 0;
+}
+core_initcall(cpu_pm_init);
+#endif
diff --git a/kernel/events/core.c b/kernel/events/core.c
index 0f85778..fbe38f2 100644
--- a/kernel/events/core.c
+++ b/kernel/events/core.c
@@ -5758,6 +5758,7 @@
 	pmu = idr_find(&pmu_idr, event->attr.type);
 	rcu_read_unlock();
 	if (pmu) {
+		event->pmu = pmu;
 		ret = pmu->event_init(event);
 		if (ret)
 			pmu = ERR_PTR(ret);
@@ -5765,6 +5766,7 @@
 	}
 
 	list_for_each_entry_rcu(pmu, &pmus, entry) {
+		event->pmu = pmu;
 		ret = pmu->event_init(event);
 		if (!ret)
 			goto unlock;
@@ -5891,8 +5893,6 @@
 		return ERR_PTR(err);
 	}
 
-	event->pmu = pmu;
-
 	if (!event->parent) {
 		if (event->attach_state & PERF_ATTACH_TASK)
 			jump_label_inc(&perf_sched_events);
diff --git a/kernel/irq/chip.c b/kernel/irq/chip.c
index dc5114b..f7c543a 100644
--- a/kernel/irq/chip.c
+++ b/kernel/irq/chip.c
@@ -26,7 +26,7 @@
 int irq_set_chip(unsigned int irq, struct irq_chip *chip)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_lock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_lock(irq, &flags, 0);
 
 	if (!desc)
 		return -EINVAL;
@@ -54,7 +54,7 @@
 int irq_set_irq_type(unsigned int irq, unsigned int type)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_buslock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_buslock(irq, &flags, IRQ_GET_DESC_CHECK_GLOBAL);
 	int ret = 0;
 
 	if (!desc)
@@ -78,7 +78,7 @@
 int irq_set_handler_data(unsigned int irq, void *data)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_lock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_lock(irq, &flags, 0);
 
 	if (!desc)
 		return -EINVAL;
@@ -98,7 +98,7 @@
 int irq_set_msi_desc(unsigned int irq, struct msi_desc *entry)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_lock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_lock(irq, &flags, IRQ_GET_DESC_CHECK_GLOBAL);
 
 	if (!desc)
 		return -EINVAL;
@@ -119,7 +119,7 @@
 int irq_set_chip_data(unsigned int irq, void *data)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_lock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_lock(irq, &flags, 0);
 
 	if (!desc)
 		return -EINVAL;
@@ -204,6 +204,24 @@
 	}
 }
 
+void irq_percpu_enable(struct irq_desc *desc, unsigned int cpu)
+{
+	if (desc->irq_data.chip->irq_enable)
+		desc->irq_data.chip->irq_enable(&desc->irq_data);
+	else
+		desc->irq_data.chip->irq_unmask(&desc->irq_data);
+	cpumask_set_cpu(cpu, desc->percpu_enabled);
+}
+
+void irq_percpu_disable(struct irq_desc *desc, unsigned int cpu)
+{
+	if (desc->irq_data.chip->irq_disable)
+		desc->irq_data.chip->irq_disable(&desc->irq_data);
+	else
+		desc->irq_data.chip->irq_mask(&desc->irq_data);
+	cpumask_clear_cpu(cpu, desc->percpu_enabled);
+}
+
 static inline void mask_ack_irq(struct irq_desc *desc)
 {
 	if (desc->irq_data.chip->irq_mask_ack)
@@ -544,12 +562,44 @@
 		chip->irq_eoi(&desc->irq_data);
 }
 
+/**
+ * handle_percpu_devid_irq - Per CPU local irq handler with per cpu dev ids
+ * @irq:	the interrupt number
+ * @desc:	the interrupt description structure for this irq
+ *
+ * Per CPU interrupts on SMP machines without locking requirements. Same as
+ * handle_percpu_irq() above but with the following extras:
+ *
+ * action->percpu_dev_id is a pointer to percpu variables which
+ * contain the real device id for the cpu on which this handler is
+ * called
+ */
+void handle_percpu_devid_irq(unsigned int irq, struct irq_desc *desc)
+{
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+	struct irqaction *action = desc->action;
+	void *dev_id = __this_cpu_ptr(action->percpu_dev_id);
+	irqreturn_t res;
+
+	kstat_incr_irqs_this_cpu(irq, desc);
+
+	if (chip->irq_ack)
+		chip->irq_ack(&desc->irq_data);
+
+	trace_irq_handler_entry(irq, action);
+	res = action->handler(irq, dev_id);
+	trace_irq_handler_exit(irq, action, res);
+
+	if (chip->irq_eoi)
+		chip->irq_eoi(&desc->irq_data);
+}
+
 void
 __irq_set_handler(unsigned int irq, irq_flow_handler_t handle, int is_chained,
 		  const char *name)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_buslock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_buslock(irq, &flags, 0);
 
 	if (!desc)
 		return;
@@ -593,7 +643,7 @@
 void irq_modify_status(unsigned int irq, unsigned long clr, unsigned long set)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_lock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_lock(irq, &flags, 0);
 
 	if (!desc)
 		return;
diff --git a/kernel/irq/internals.h b/kernel/irq/internals.h
index 6546431..a73dd6c 100644
--- a/kernel/irq/internals.h
+++ b/kernel/irq/internals.h
@@ -71,6 +71,8 @@
 extern void irq_shutdown(struct irq_desc *desc);
 extern void irq_enable(struct irq_desc *desc);
 extern void irq_disable(struct irq_desc *desc);
+extern void irq_percpu_enable(struct irq_desc *desc, unsigned int cpu);
+extern void irq_percpu_disable(struct irq_desc *desc, unsigned int cpu);
 extern void mask_irq(struct irq_desc *desc);
 extern void unmask_irq(struct irq_desc *desc);
 
@@ -114,14 +116,21 @@
 		desc->irq_data.chip->irq_bus_sync_unlock(&desc->irq_data);
 }
 
+#define _IRQ_DESC_CHECK		(1 << 0)
+#define _IRQ_DESC_PERCPU	(1 << 1)
+
+#define IRQ_GET_DESC_CHECK_GLOBAL	(_IRQ_DESC_CHECK)
+#define IRQ_GET_DESC_CHECK_PERCPU	(_IRQ_DESC_CHECK | _IRQ_DESC_PERCPU)
+
 struct irq_desc *
-__irq_get_desc_lock(unsigned int irq, unsigned long *flags, bool bus);
+__irq_get_desc_lock(unsigned int irq, unsigned long *flags, bool bus,
+		    unsigned int check);
 void __irq_put_desc_unlock(struct irq_desc *desc, unsigned long flags, bool bus);
 
 static inline struct irq_desc *
-irq_get_desc_buslock(unsigned int irq, unsigned long *flags)
+irq_get_desc_buslock(unsigned int irq, unsigned long *flags, unsigned int check)
 {
-	return __irq_get_desc_lock(irq, flags, true);
+	return __irq_get_desc_lock(irq, flags, true, check);
 }
 
 static inline void
@@ -131,9 +140,9 @@
 }
 
 static inline struct irq_desc *
-irq_get_desc_lock(unsigned int irq, unsigned long *flags)
+irq_get_desc_lock(unsigned int irq, unsigned long *flags, unsigned int check)
 {
-	return __irq_get_desc_lock(irq, flags, false);
+	return __irq_get_desc_lock(irq, flags, false, check);
 }
 
 static inline void
diff --git a/kernel/irq/irqdesc.c b/kernel/irq/irqdesc.c
index 039b889..1550e84 100644
--- a/kernel/irq/irqdesc.c
+++ b/kernel/irq/irqdesc.c
@@ -424,11 +424,22 @@
 }
 
 struct irq_desc *
-__irq_get_desc_lock(unsigned int irq, unsigned long *flags, bool bus)
+__irq_get_desc_lock(unsigned int irq, unsigned long *flags, bool bus,
+		    unsigned int check)
 {
 	struct irq_desc *desc = irq_to_desc(irq);
 
 	if (desc) {
+		if (check & _IRQ_DESC_CHECK) {
+			if ((check & _IRQ_DESC_PERCPU) &&
+			    !irq_settings_is_per_cpu_devid(desc))
+				return NULL;
+
+			if (!(check & _IRQ_DESC_PERCPU) &&
+			    irq_settings_is_per_cpu_devid(desc))
+				return NULL;
+		}
+
 		if (bus)
 			chip_bus_lock(desc);
 		raw_spin_lock_irqsave(&desc->lock, *flags);
@@ -443,6 +454,25 @@
 		chip_bus_sync_unlock(desc);
 }
 
+int irq_set_percpu_devid(unsigned int irq)
+{
+	struct irq_desc *desc = irq_to_desc(irq);
+
+	if (!desc)
+		return -EINVAL;
+
+	if (desc->percpu_enabled)
+		return -EINVAL;
+
+	desc->percpu_enabled = kzalloc(sizeof(*desc->percpu_enabled), GFP_KERNEL);
+
+	if (!desc->percpu_enabled)
+		return -ENOMEM;
+
+	irq_set_percpu_devid_flags(irq);
+	return 0;
+}
+
 /**
  * dynamic_irq_cleanup - cleanup a dynamically allocated irq
  * @irq:	irq number to initialize
diff --git a/kernel/irq/irqdomain.c b/kernel/irq/irqdomain.c
index b57a377..200ce83 100644
--- a/kernel/irq/irqdomain.c
+++ b/kernel/irq/irqdomain.c
@@ -20,15 +20,15 @@
 void irq_domain_add(struct irq_domain *domain)
 {
 	struct irq_data *d;
-	int hwirq;
+	int hwirq, irq;
 
 	/*
 	 * This assumes that the irq_domain owner has already allocated
 	 * the irq_descs.  This block will be removed when support for dynamic
 	 * allocation of irq_descs is added to irq_domain.
 	 */
-	for (hwirq = 0; hwirq < domain->nr_irq; hwirq++) {
-		d = irq_get_irq_data(irq_domain_to_irq(domain, hwirq));
+	irq_domain_for_each_irq(domain, hwirq, irq) {
+		d = irq_get_irq_data(irq);
 		if (!d) {
 			WARN(1, "error: assigning domain to non existant irq_desc");
 			return;
@@ -54,15 +54,15 @@
 void irq_domain_del(struct irq_domain *domain)
 {
 	struct irq_data *d;
-	int hwirq;
+	int hwirq, irq;
 
 	mutex_lock(&irq_domain_mutex);
 	list_del(&domain->list);
 	mutex_unlock(&irq_domain_mutex);
 
 	/* Clear the irq_domain assignments */
-	for (hwirq = 0; hwirq < domain->nr_irq; hwirq++) {
-		d = irq_get_irq_data(irq_domain_to_irq(domain, hwirq));
+	irq_domain_for_each_irq(domain, hwirq, irq) {
+		d = irq_get_irq_data(irq);
 		d->domain = NULL;
 	}
 }
diff --git a/kernel/irq/manage.c b/kernel/irq/manage.c
index 9b956fa..67ce837 100644
--- a/kernel/irq/manage.c
+++ b/kernel/irq/manage.c
@@ -195,7 +195,7 @@
 int irq_set_affinity_hint(unsigned int irq, const struct cpumask *m)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_lock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_lock(irq, &flags, IRQ_GET_DESC_CHECK_GLOBAL);
 
 	if (!desc)
 		return -EINVAL;
@@ -356,7 +356,7 @@
 static int __disable_irq_nosync(unsigned int irq)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_buslock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_buslock(irq, &flags, IRQ_GET_DESC_CHECK_GLOBAL);
 
 	if (!desc)
 		return -EINVAL;
@@ -448,7 +448,7 @@
 void enable_irq(unsigned int irq)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_buslock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_buslock(irq, &flags, IRQ_GET_DESC_CHECK_GLOBAL);
 
 	if (!desc)
 		return;
@@ -467,6 +467,9 @@
 	struct irq_desc *desc = irq_to_desc(irq);
 	int ret = -ENXIO;
 
+	if (irq_desc_get_chip(desc)->flags &  IRQCHIP_SKIP_SET_WAKE)
+		return 0;
+
 	if (desc->irq_data.chip->irq_set_wake)
 		ret = desc->irq_data.chip->irq_set_wake(&desc->irq_data, on);
 
@@ -488,7 +491,7 @@
 int irq_set_irq_wake(unsigned int irq, unsigned int on)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_buslock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_buslock(irq, &flags, IRQ_GET_DESC_CHECK_GLOBAL);
 	int ret = 0;
 
 	if (!desc)
@@ -529,7 +532,7 @@
 int can_request_irq(unsigned int irq, unsigned long irqflags)
 {
 	unsigned long flags;
-	struct irq_desc *desc = irq_get_desc_lock(irq, &flags);
+	struct irq_desc *desc = irq_get_desc_lock(irq, &flags, 0);
 	int canrequest = 0;
 
 	if (!desc)
@@ -1118,6 +1121,8 @@
 	int retval;
 	struct irq_desc *desc = irq_to_desc(irq);
 
+	if (WARN_ON(irq_settings_is_per_cpu_devid(desc)))
+		return -EINVAL;
 	chip_bus_lock(desc);
 	retval = __setup_irq(irq, desc, act);
 	chip_bus_sync_unlock(desc);
@@ -1126,7 +1131,7 @@
 }
 EXPORT_SYMBOL_GPL(setup_irq);
 
- /*
+/*
  * Internal function to unregister an irqaction - used to free
  * regular and special interrupts that are part of the architecture.
  */
@@ -1224,7 +1229,10 @@
  */
 void remove_irq(unsigned int irq, struct irqaction *act)
 {
-	__free_irq(irq, act->dev_id);
+	struct irq_desc *desc = irq_to_desc(irq);
+
+	if (desc && !WARN_ON(irq_settings_is_per_cpu_devid(desc)))
+	    __free_irq(irq, act->dev_id);
 }
 EXPORT_SYMBOL_GPL(remove_irq);
 
@@ -1246,7 +1254,7 @@
 {
 	struct irq_desc *desc = irq_to_desc(irq);
 
-	if (!desc)
+	if (!desc || WARN_ON(irq_settings_is_per_cpu_devid(desc)))
 		return;
 
 #ifdef CONFIG_SMP
@@ -1324,7 +1332,8 @@
 	if (!desc)
 		return -EINVAL;
 
-	if (!irq_settings_can_request(desc))
+	if (!irq_settings_can_request(desc) ||
+	    WARN_ON(irq_settings_is_per_cpu_devid(desc)))
 		return -EINVAL;
 
 	if (!handler) {
@@ -1409,3 +1418,194 @@
 	return !ret ? IRQC_IS_HARDIRQ : ret;
 }
 EXPORT_SYMBOL_GPL(request_any_context_irq);
+
+void enable_percpu_irq(unsigned int irq, unsigned int type)
+{
+	unsigned int cpu = smp_processor_id();
+	unsigned long flags;
+	struct irq_desc *desc = irq_get_desc_lock(irq, &flags, IRQ_GET_DESC_CHECK_PERCPU);
+
+	if (!desc)
+		return;
+
+	type &= IRQ_TYPE_SENSE_MASK;
+	if (type != IRQ_TYPE_NONE) {
+		int ret;
+
+		ret = __irq_set_trigger(desc, irq, type);
+
+		if (ret) {
+			WARN(1, "failed to set type for IRQ%d\n", irq);
+			goto out;
+		}
+	}
+
+	irq_percpu_enable(desc, cpu);
+out:
+	irq_put_desc_unlock(desc, flags);
+}
+
+void disable_percpu_irq(unsigned int irq)
+{
+	unsigned int cpu = smp_processor_id();
+	unsigned long flags;
+	struct irq_desc *desc = irq_get_desc_lock(irq, &flags, IRQ_GET_DESC_CHECK_PERCPU);
+
+	if (!desc)
+		return;
+
+	irq_percpu_disable(desc, cpu);
+	irq_put_desc_unlock(desc, flags);
+}
+
+/*
+ * Internal function to unregister a percpu irqaction.
+ */
+static struct irqaction *__free_percpu_irq(unsigned int irq, void __percpu *dev_id)
+{
+	struct irq_desc *desc = irq_to_desc(irq);
+	struct irqaction *action;
+	unsigned long flags;
+
+	WARN(in_interrupt(), "Trying to free IRQ %d from IRQ context!\n", irq);
+
+	if (!desc)
+		return NULL;
+
+	raw_spin_lock_irqsave(&desc->lock, flags);
+
+	action = desc->action;
+	if (!action || action->percpu_dev_id != dev_id) {
+		WARN(1, "Trying to free already-free IRQ %d\n", irq);
+		goto bad;
+	}
+
+	if (!cpumask_empty(desc->percpu_enabled)) {
+		WARN(1, "percpu IRQ %d still enabled on CPU%d!\n",
+		     irq, cpumask_first(desc->percpu_enabled));
+		goto bad;
+	}
+
+	/* Found it - now remove it from the list of entries: */
+	desc->action = NULL;
+
+	raw_spin_unlock_irqrestore(&desc->lock, flags);
+
+	unregister_handler_proc(irq, action);
+
+	module_put(desc->owner);
+	return action;
+
+bad:
+	raw_spin_unlock_irqrestore(&desc->lock, flags);
+	return NULL;
+}
+
+/**
+ *	remove_percpu_irq - free a per-cpu interrupt
+ *	@irq: Interrupt line to free
+ *	@act: irqaction for the interrupt
+ *
+ * Used to remove interrupts statically setup by the early boot process.
+ */
+void remove_percpu_irq(unsigned int irq, struct irqaction *act)
+{
+	struct irq_desc *desc = irq_to_desc(irq);
+
+	if (desc && irq_settings_is_per_cpu_devid(desc))
+	    __free_percpu_irq(irq, act->percpu_dev_id);
+}
+
+/**
+ *	free_percpu_irq - free an interrupt allocated with request_percpu_irq
+ *	@irq: Interrupt line to free
+ *	@dev_id: Device identity to free
+ *
+ *	Remove a percpu interrupt handler. The handler is removed, but
+ *	the interrupt line is not disabled. This must be done on each
+ *	CPU before calling this function. The function does not return
+ *	until any executing interrupts for this IRQ have completed.
+ *
+ *	This function must not be called from interrupt context.
+ */
+void free_percpu_irq(unsigned int irq, void __percpu *dev_id)
+{
+	struct irq_desc *desc = irq_to_desc(irq);
+
+	if (!desc || !irq_settings_is_per_cpu_devid(desc))
+		return;
+
+	chip_bus_lock(desc);
+	kfree(__free_percpu_irq(irq, dev_id));
+	chip_bus_sync_unlock(desc);
+}
+
+/**
+ *	setup_percpu_irq - setup a per-cpu interrupt
+ *	@irq: Interrupt line to setup
+ *	@act: irqaction for the interrupt
+ *
+ * Used to statically setup per-cpu interrupts in the early boot process.
+ */
+int setup_percpu_irq(unsigned int irq, struct irqaction *act)
+{
+	struct irq_desc *desc = irq_to_desc(irq);
+	int retval;
+
+	if (!desc || !irq_settings_is_per_cpu_devid(desc))
+		return -EINVAL;
+	chip_bus_lock(desc);
+	retval = __setup_irq(irq, desc, act);
+	chip_bus_sync_unlock(desc);
+
+	return retval;
+}
+
+/**
+ *	request_percpu_irq - allocate a percpu interrupt line
+ *	@irq: Interrupt line to allocate
+ *	@handler: Function to be called when the IRQ occurs.
+ *	@devname: An ascii name for the claiming device
+ *	@dev_id: A percpu cookie passed back to the handler function
+ *
+ *	This call allocates interrupt resources, but doesn't
+ *	automatically enable the interrupt. It has to be done on each
+ *	CPU using enable_percpu_irq().
+ *
+ *	Dev_id must be globally unique. It is a per-cpu variable, and
+ *	the handler gets called with the interrupted CPU's instance of
+ *	that variable.
+ */
+int request_percpu_irq(unsigned int irq, irq_handler_t handler,
+		       const char *devname, void __percpu *dev_id)
+{
+	struct irqaction *action;
+	struct irq_desc *desc;
+	int retval;
+
+	if (!dev_id)
+		return -EINVAL;
+
+	desc = irq_to_desc(irq);
+	if (!desc || !irq_settings_can_request(desc) ||
+	    !irq_settings_is_per_cpu_devid(desc))
+		return -EINVAL;
+
+	action = kzalloc(sizeof(struct irqaction), GFP_KERNEL);
+	if (!action)
+		return -ENOMEM;
+
+	action->handler = handler;
+	action->flags = IRQF_PERCPU;
+	action->name = devname;
+	action->percpu_dev_id = dev_id;
+
+	chip_bus_lock(desc);
+	retval = __setup_irq(irq, desc, action);
+	chip_bus_sync_unlock(desc);
+
+	if (retval)
+		kfree(action);
+
+	return retval;
+}
diff --git a/kernel/irq/settings.h b/kernel/irq/settings.h
index f166783..1162f10 100644
--- a/kernel/irq/settings.h
+++ b/kernel/irq/settings.h
@@ -13,6 +13,7 @@
 	_IRQ_MOVE_PCNTXT	= IRQ_MOVE_PCNTXT,
 	_IRQ_NO_BALANCING	= IRQ_NO_BALANCING,
 	_IRQ_NESTED_THREAD	= IRQ_NESTED_THREAD,
+	_IRQ_PER_CPU_DEVID	= IRQ_PER_CPU_DEVID,
 	_IRQF_MODIFY_MASK	= IRQF_MODIFY_MASK,
 };
 
@@ -24,6 +25,7 @@
 #define IRQ_NOTHREAD		GOT_YOU_MORON
 #define IRQ_NOAUTOEN		GOT_YOU_MORON
 #define IRQ_NESTED_THREAD	GOT_YOU_MORON
+#define IRQ_PER_CPU_DEVID	GOT_YOU_MORON
 #undef IRQF_MODIFY_MASK
 #define IRQF_MODIFY_MASK	GOT_YOU_MORON
 
@@ -39,6 +41,11 @@
 	return desc->status_use_accessors & _IRQ_PER_CPU;
 }
 
+static inline bool irq_settings_is_per_cpu_devid(struct irq_desc *desc)
+{
+	return desc->status_use_accessors & _IRQ_PER_CPU_DEVID;
+}
+
 static inline void irq_settings_set_per_cpu(struct irq_desc *desc)
 {
 	desc->status_use_accessors |= _IRQ_PER_CPU;
diff --git a/kernel/power/Kconfig b/kernel/power/Kconfig
index 3744c59..80a8597 100644
--- a/kernel/power/Kconfig
+++ b/kernel/power/Kconfig
@@ -235,3 +235,7 @@
 config PM_GENERIC_DOMAINS_RUNTIME
 	def_bool y
 	depends on PM_RUNTIME && PM_GENERIC_DOMAINS
+
+config CPU_PM
+	bool
+	depends on SUSPEND || CPU_IDLE