diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
index 64bcb8b..0d93b4b 100644
--- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
+++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
@@ -11,9 +11,11 @@
   - interrupt-parent : interrupt source phandle.
   - clock-frequency : specifies eSDHC base clock frequency.
   - sdhci,wp-inverted : (optional) specifies that eSDHC controller
-    reports inverted write-protect state;
+    reports inverted write-protect state; New devices should use
+    the generic "wp-inverted" property.
   - sdhci,1-bit-only : (optional) specifies that a controller can
-    only handle 1-bit data transfers.
+    only handle 1-bit data transfers. New devices should use the
+    generic "bus-width = <1>" property.
   - sdhci,auto-cmd12: (optional) specifies that a controller can
     only handle auto CMD12.
 
diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
index ab22fe6..c7e404b 100644
--- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
+++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
@@ -9,7 +9,7 @@
 - interrupts : Should contain eSDHC interrupt
 
 Optional properties:
-- fsl,card-wired : Indicate the card is wired to host permanently
+- non-removable : Indicate the card is wired to host permanently
 - fsl,cd-internal : Indicate to use controller internal card detection
 - fsl,wp-internal : Indicate to use controller internal write protection
 - cd-gpios : Specify GPIOs for card detection
diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
index 89a0084..d64aea5 100644
--- a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
@@ -10,7 +10,8 @@
 
 Optional properties:
 - gpios : may specify GPIOs in this order: Card-Detect GPIO,
-  Write-Protect GPIO.
+  Write-Protect GPIO. Note that this does not follow the
+  binding from mmc.txt, for historic reasons.
 - interrupts : the interrupt of a card detect interrupt.
 - interrupt-parent : the phandle for the interrupt controller that
   services interrupts for this device.
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
new file mode 100644
index 0000000..6e70dcd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -0,0 +1,27 @@
+These properties are common to multiple MMC host controllers. Any host
+that requires the respective functionality should implement them using
+these definitions.
+
+Required properties:
+- bus-width: Number of data lines, can be <1>, <4>, or <8>
+
+Optional properties:
+- cd-gpios : Specify GPIOs for card detection, see gpio binding
+- wp-gpios : Specify GPIOs for write protection, see gpio binding
+- cd-inverted: when present, polarity on the wp gpio line is inverted
+- wp-inverted: when present, polarity on the wp gpio line is inverted
+- non-removable: non-removable slot (like eMMC)
+- max-frequency: maximum operating clock frequency
+
+Example:
+
+sdhci@ab000000 {
+	compatible = "sdhci";
+	reg = <0xab000000 0x200>;
+	interrupts = <23>;
+	bus-width = <4>;
+	cd-gpios = <&gpio 69 0>;
+	cd-inverted;
+	wp-gpios = <&gpio 70 0>;
+	max-frequency = <50000000>;
+}
diff --git a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt
index 7e51154..f77c303 100644
--- a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt
+++ b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt
@@ -7,12 +7,12 @@
 - compatible : Should be "nvidia,<chip>-sdhci"
 - reg : Should contain SD/MMC registers location and length
 - interrupts : Should contain SD/MMC interrupt
+- bus-width : Number of data lines, can be <1>, <4>, or <8>
 
 Optional properties:
 - cd-gpios : Specify GPIOs for card detection
 - wp-gpios : Specify GPIOs for write protection
 - power-gpios : Specify GPIOs for power control
-- support-8bit : Boolean, indicates if 8-bit mode should be used.
 
 Example:
 
@@ -23,5 +23,5 @@
 	cd-gpios = <&gpio 69 0>; /* gpio PI5 */
 	wp-gpios = <&gpio 57 0>; /* gpio PH1 */
 	power-gpios = <&gpio 155 0>; /* gpio PT3 */
-	support-8bit;
+	bus-width = <8>;
 };
diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
index dbd4368..8a53958 100644
--- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
+++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
@@ -15,7 +15,7 @@
 ti,dual-volt: boolean, supports dual voltage cards
 <supply-name>-supply: phandle to the regulator device tree node
 "supply-name" examples are "vmmc", "vmmc_aux" etc
-ti,bus-width: Number of data lines, default assumed is 1 if the property is missing.
+bus-width: Number of data lines, default assumed is 1 if the property is missing.
 cd-gpios: GPIOs for card detection
 wp-gpios: GPIOs for write protection
 ti,non-removable: non-removable slot (like eMMC)
@@ -27,7 +27,7 @@
 		reg = <0x4809c000 0x400>;
 		ti,hwmods = "mmc1";
 		ti,dual-volt;
-		ti,bus-width = <4>;
+		bus-width = <4>;
 		vmmc-supply = <&vmmc>; /* phandle to regulator node */
 		ti,non-removable;
 	};