cfg80211: Allow a scan request for a specific BSSID
This allows scans for a specific BSSID to be optimized by the user space
application by requesting the driver to set the Probe Request frame
BSSID field (Address 3) to the specified BSSID instead of the wildcard
BSSID. This prevents other APs from replying which reduces airtime need
and latency in getting the response from the target AP through.
This is an optimization and as such, it is acceptable for some of the
drivers not to support the mechanism. If not supported, the wildcard
BSSID will be used and more responses may be received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 9e1b24c..14c0c43 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -1455,6 +1455,7 @@
* @mac_addr_mask: MAC address mask used with randomisation, bits that
* are 0 in the mask should be randomised, bits that are 1 should
* be taken from the @mac_addr
+ * @bssid: BSSID to scan for (most commonly, the wildcard BSSID)
*/
struct cfg80211_scan_request {
struct cfg80211_ssid *ssids;
@@ -1471,6 +1472,7 @@
u8 mac_addr[ETH_ALEN] __aligned(2);
u8 mac_addr_mask[ETH_ALEN] __aligned(2);
+ u8 bssid[ETH_ALEN] __aligned(2);
/* internal */
struct wiphy *wiphy;
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
index 5a30a75..23bf066 100644
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -322,7 +322,9 @@
* @NL80211_CMD_GET_SCAN: get scan results
* @NL80211_CMD_TRIGGER_SCAN: trigger a new scan with the given parameters
* %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
- * probe requests at CCK rate or not.
+ * probe requests at CCK rate or not. %NL80211_ATTR_MAC can be used to
+ * specify a BSSID to scan for; if not included, the wildcard BSSID will
+ * be used.
* @NL80211_CMD_NEW_SCAN_RESULTS: scan notification (as a reply to
* NL80211_CMD_GET_SCAN and on the "scan" multicast group)
* @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons,
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index 98c9242..1b43f78 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -5996,6 +5996,12 @@
request->no_cck =
nla_get_flag(info->attrs[NL80211_ATTR_TX_NO_CCK_RATE]);
+ if (info->attrs[NL80211_ATTR_MAC])
+ memcpy(request->bssid, nla_data(info->attrs[NL80211_ATTR_MAC]),
+ ETH_ALEN);
+ else
+ eth_broadcast_addr(request->bssid);
+
request->wdev = wdev;
request->wiphy = &rdev->wiphy;
request->scan_start = jiffies;
diff --git a/net/wireless/scan.c b/net/wireless/scan.c
index 14d5369e..50ea8e3 100644
--- a/net/wireless/scan.c
+++ b/net/wireless/scan.c
@@ -1293,6 +1293,8 @@
if (wiphy->bands[i])
creq->rates[i] = (1 << wiphy->bands[i]->n_bitrates) - 1;
+ eth_broadcast_addr(creq->bssid);
+
rdev->scan_req = creq;
err = rdev_scan(rdev, creq);
if (err) {
diff --git a/net/wireless/sme.c b/net/wireless/sme.c
index 5445581..65882d2 100644
--- a/net/wireless/sme.c
+++ b/net/wireless/sme.c
@@ -119,6 +119,8 @@
wdev->conn->params.ssid_len);
request->ssids[0].ssid_len = wdev->conn->params.ssid_len;
+ eth_broadcast_addr(request->bssid);
+
request->wdev = wdev;
request->wiphy = &rdev->wiphy;
request->scan_start = jiffies;