wl1271: Rewrite hardware keep-alive handling
The driver had a join command without keep-alive restart procedures in the
channel changing code. After associated scans, the mac80211 does re-set the
current channel, causing the join to occur. This would stop the hardware
keep alive.
To make the joins safer in this respect, this patch adds a join function that
does the hardware-keep-alive magic along the join. This is now invoked in the
above mentioned scenario, and also other scenarios.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/wl12xx/wl1271_main.c b/drivers/net/wireless/wl12xx/wl1271_main.c
index c160e5a..a794d5e 100644
--- a/drivers/net/wireless/wl12xx/wl1271_main.c
+++ b/drivers/net/wireless/wl12xx/wl1271_main.c
@@ -1117,14 +1117,13 @@
}
}
-static int wl1271_join_channel(struct wl1271 *wl, int channel)
+static int wl1271_dummy_join(struct wl1271 *wl)
{
int ret = 0;
/* we need to use a dummy BSSID for now */
static const u8 dummy_bssid[ETH_ALEN] = { 0x0b, 0xad, 0xde,
0xad, 0xbe, 0xef };
- wl->channel = channel;
memcpy(wl->bssid, dummy_bssid, ETH_ALEN);
/* pass through frames from all BSS */
@@ -1140,7 +1139,47 @@
return ret;
}
-static int wl1271_unjoin_channel(struct wl1271 *wl)
+static int wl1271_join(struct wl1271 *wl)
+{
+ int ret;
+
+ ret = wl1271_cmd_join(wl, wl->set_bss_type);
+ if (ret < 0)
+ goto out;
+
+ set_bit(WL1271_FLAG_JOINED, &wl->flags);
+
+ if (!test_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags))
+ goto out;
+
+ /*
+ * The join command disable the keep-alive mode, shut down its process,
+ * and also clear the template config, so we need to reset it all after
+ * the join. The acx_aid starts the keep-alive process, and the order
+ * of the commands below is relevant.
+ */
+ ret = wl1271_acx_keep_alive_mode(wl, true);
+ if (ret < 0)
+ goto out;
+
+ ret = wl1271_acx_aid(wl, wl->aid);
+ if (ret < 0)
+ goto out;
+
+ ret = wl1271_cmd_build_klv_null_data(wl);
+ if (ret < 0)
+ goto out;
+
+ ret = wl1271_acx_keep_alive_config(wl, CMD_TEMPL_KLV_IDX_NULL_DATA,
+ ACX_KEEP_ALIVE_TPL_VALID);
+ if (ret < 0)
+ goto out;
+
+out:
+ return ret;
+}
+
+static int wl1271_unjoin(struct wl1271 *wl)
{
int ret;
@@ -1230,7 +1269,7 @@
"failed %d", ret);
if (test_bit(WL1271_FLAG_JOINED, &wl->flags)) {
- ret = wl1271_cmd_join(wl, wl->set_bss_type);
+ ret = wl1271_join(wl);
if (ret < 0)
wl1271_warning("cmd join to update channel "
"failed %d", ret);
@@ -1240,9 +1279,9 @@
if (changed & IEEE80211_CONF_CHANGE_IDLE) {
if (conf->flags & IEEE80211_CONF_IDLE &&
test_bit(WL1271_FLAG_JOINED, &wl->flags))
- wl1271_unjoin_channel(wl);
+ wl1271_unjoin(wl);
else if (!(conf->flags & IEEE80211_CONF_IDLE))
- wl1271_join_channel(wl, channel);
+ wl1271_dummy_join(wl);
if (conf->flags & IEEE80211_CONF_IDLE) {
wl->rate_set = wl1271_min_rate_get(wl);
@@ -1612,7 +1651,6 @@
enum wl1271_cmd_ps_mode mode;
struct wl1271 *wl = hw->priv;
bool do_join = false;
- bool do_keepalive = false;
int ret;
wl1271_debug(DEBUG_MAC80211, "mac80211 bss info changed");
@@ -1755,19 +1793,6 @@
ret = wl1271_cmd_build_probe_req(wl, NULL, 0,
NULL, 0, wl->band);
- /* Enable the keep-alive feature */
- ret = wl1271_acx_keep_alive_mode(wl, true);
- if (ret < 0)
- goto out_sleep;
-
- /*
- * This is awkward. The keep-alive configs must be done
- * *after* the join command, because otherwise it will
- * not work, but it must only be done *once* because
- * otherwise the firmware will start complaining.
- */
- do_keepalive = true;
-
/* enable the connection monitoring feature */
ret = wl1271_acx_conn_monit_params(wl, true);
if (ret < 0)
@@ -1835,35 +1860,11 @@
}
if (do_join) {
- ret = wl1271_cmd_join(wl, wl->set_bss_type);
+ ret = wl1271_join(wl);
if (ret < 0) {
wl1271_warning("cmd join failed %d", ret);
goto out_sleep;
}
- set_bit(WL1271_FLAG_JOINED, &wl->flags);
- }
-
- /*
- * The JOIN operation shuts down the firmware keep-alive as a side
- * effect, and the ACX_AID will start the keep-alive as a side effect.
- * Hence, for non-IBSS, the ACX_AID must always happen *after* the
- * JOIN operation, and the template config after the ACX_AID.
- */
- if (test_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags)) {
- ret = wl1271_acx_aid(wl, wl->aid);
- if (ret < 0)
- goto out_sleep;
- }
-
- if (do_keepalive) {
- ret = wl1271_cmd_build_klv_null_data(wl);
- if (ret < 0)
- goto out_sleep;
- ret = wl1271_acx_keep_alive_config(
- wl, CMD_TEMPL_KLV_IDX_NULL_DATA,
- ACX_KEEP_ALIVE_TPL_VALID);
- if (ret < 0)
- goto out_sleep;
}
out_sleep: