AX88796 network driver
Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.
The driver supports PHY settings via either ioctl() or
the ethtool driver ops.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/8390.h b/drivers/net/8390.h
index 414de5b..04ddec0 100644
--- a/drivers/net/8390.h
+++ b/drivers/net/8390.h
@@ -73,6 +73,9 @@
u32 *reg_offset; /* Register mapping table */
spinlock_t page_lock; /* Page register locks */
unsigned long priv; /* Private field to store bus IDs etc. */
+#ifdef AX88796_PLATFORM
+ unsigned char rxcr_base; /* default value for RXCR */
+#endif
};
/* The maximum number of 8390 interrupt service routines called per IRQ. */
@@ -86,11 +89,19 @@
/* Some generic ethernet register configurations. */
#define E8390_TX_IRQ_MASK 0xa /* For register EN0_ISR */
#define E8390_RX_IRQ_MASK 0x5
+
+#ifdef AX88796_PLATFORM
+#define E8390_RXCONFIG (ei_status.rxcr_base | 0x04)
+#define E8390_RXOFF (ei_status.rxcr_base | 0x20)
+#else
#define E8390_RXCONFIG 0x4 /* EN0_RXCR: broadcasts, no multicast,errors */
#define E8390_RXOFF 0x20 /* EN0_RXCR: Accept no packets */
+#endif
+
#define E8390_TXCONFIG 0x00 /* EN0_TXCR: Normal transmit mode */
#define E8390_TXOFF 0x02 /* EN0_TXCR: Transmitter off */
+
/* Register accessed at EN_CMD, the 8390 base addr. */
#define E8390_STOP 0x01 /* Stop and reset the chip */
#define E8390_START 0x02 /* Start the chip, clear reset */
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 4f23ad7..09c6898 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -197,6 +197,14 @@
source "drivers/net/arm/Kconfig"
+config AX88796
+ tristate "ASIX AX88796 NE2000 clone support"
+ select CRC32
+ select MII
+ help
+ AX88796 driver, using platform bus to provide
+ chip detection and resources
+
config MACE
tristate "MACE (Power Mac ethernet) support"
depends on PPC_PMAC && PPC32
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index eb62fb4..515ca66 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -107,6 +107,7 @@
obj-$(CONFIG_B44) += b44.o
obj-$(CONFIG_FORCEDETH) += forcedeth.o
obj-$(CONFIG_NE_H8300) += ne-h8300.o
+obj-$(CONFIG_AX88796) += ax88796.o
obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o
obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o
diff --git a/drivers/net/ax88796.c b/drivers/net/ax88796.c
new file mode 100644
index 0000000..d19874b
--- /dev/null
+++ b/drivers/net/ax88796.c
@@ -0,0 +1,952 @@
+/* drivers/net/ax88796.c
+ *
+ * Copyright 2005,2007 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * Asix AX88796 10/100 Ethernet controller support
+ * Based on ne.c, by Donald Becker, et-al.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/isapnp.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/mii.h>
+
+#include <net/ax88796.h>
+
+#include <asm/system.h>
+#include <asm/io.h>
+
+static int phy_debug = 0;
+
+/* Rename the lib8390.c functions to show that they are in this driver */
+#define __ei_open ax_ei_open
+#define __ei_close ax_ei_close
+#define __ei_poll ax_ei_poll
+#define __ei_tx_timeout ax_ei_tx_timeout
+#define __ei_interrupt ax_ei_interrupt
+#define ____alloc_ei_netdev ax__alloc_ei_netdev
+#define __NS8390_init ax_NS8390_init
+
+/* force unsigned long back to 'void __iomem *' */
+#define ax_convert_addr(_a) ((void __force __iomem *)(_a))
+
+#define ei_inb(_a) readb(ax_convert_addr(_a))
+#define ei_outb(_v, _a) writeb(_v, ax_convert_addr(_a))
+
+#define ei_inb_p(_a) ei_inb(_a)
+#define ei_outb_p(_v, _a) ei_outb(_v, _a)
+
+/* define EI_SHIFT() to take into account our register offsets */
+#define EI_SHIFT(x) (ei_local->reg_offset[(x)])
+
+/* Ensure we have our RCR base value */
+#define AX88796_PLATFORM
+
+static unsigned char version[] = "ax88796.c: Copyright 2005,2007 Simtec Electronics\n";
+
+#include "lib8390.c"
+
+#define DRV_NAME "ax88796"
+#define DRV_VERSION "1.00"
+
+/* from ne.c */
+#define NE_CMD EI_SHIFT(0x00)
+#define NE_RESET EI_SHIFT(0x1f)
+#define NE_DATAPORT EI_SHIFT(0x10)
+
+#define NE1SM_START_PG 0x20 /* First page of TX buffer */
+#define NE1SM_STOP_PG 0x40 /* Last page +1 of RX ring */
+#define NESM_START_PG 0x40 /* First page of TX buffer */
+#define NESM_STOP_PG 0x80 /* Last page +1 of RX ring */
+
+/* device private data */
+
+struct ax_device {
+ struct timer_list mii_timer;
+ spinlock_t mii_lock;
+ struct mii_if_info mii;
+
+ u32 msg_enable;
+ void __iomem *map2;
+ struct platform_device *dev;
+ struct resource *mem;
+ struct resource *mem2;
+ struct ax_plat_data *plat;
+
+ unsigned char running;
+ unsigned char resume_open;
+
+ u32 reg_offsets[0x20];
+};
+
+static inline struct ax_device *to_ax_dev(struct net_device *dev)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ return (struct ax_device *)(ei_local+1);
+}
+
+/* ax_initial_check
+ *
+ * do an initial probe for the card to check wether it exists
+ * and is functional
+ */
+
+static int ax_initial_check(struct net_device *dev)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ void __iomem *ioaddr = ei_local->mem;
+ int reg0;
+ int regd;
+
+ reg0 = ei_inb(ioaddr);
+ if (reg0 == 0xFF)
+ return -ENODEV;
+
+ ei_outb(E8390_NODMA+E8390_PAGE1+E8390_STOP, ioaddr + E8390_CMD);
+ regd = ei_inb(ioaddr + 0x0d);
+ ei_outb(0xff, ioaddr + 0x0d);
+ ei_outb(E8390_NODMA+E8390_PAGE0, ioaddr + E8390_CMD);
+ ei_inb(ioaddr + EN0_COUNTER0); /* Clear the counter by reading. */
+ if (ei_inb(ioaddr + EN0_COUNTER0) != 0) {
+ ei_outb(reg0, ioaddr);
+ ei_outb(regd, ioaddr + 0x0d); /* Restore the old values. */
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+/* Hard reset the card. This used to pause for the same period that a
+ 8390 reset command required, but that shouldn't be necessary. */
+
+static void ax_reset_8390(struct net_device *dev)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ unsigned long reset_start_time = jiffies;
+ void __iomem *addr = (void __iomem *)dev->base_addr;
+
+ if (ei_debug > 1)
+ printk(KERN_DEBUG "resetting the 8390 t=%ld...", jiffies);
+
+ ei_outb(ei_inb(addr + NE_RESET), addr + NE_RESET);
+
+ ei_status.txing = 0;
+ ei_status.dmaing = 0;
+
+ /* This check _should_not_ be necessary, omit eventually. */
+ while ((ei_inb(addr + EN0_ISR) & ENISR_RESET) == 0) {
+ if (jiffies - reset_start_time > 2*HZ/100) {
+ printk(KERN_WARNING "%s: %s did not complete.\n",
+ __FUNCTION__, dev->name);
+ break;
+ }
+ }
+
+ ei_outb(ENISR_RESET, addr + EN0_ISR); /* Ack intr. */
+}
+
+
+static void ax_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
+ int ring_page)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ void __iomem *nic_base = ei_local->mem;
+
+ /* This *shouldn't* happen. If it does, it's the last thing you'll see */
+ if (ei_status.dmaing) {
+ printk(KERN_EMERG "%s: DMAing conflict in %s [DMAstat:%d][irqlock:%d].\n",
+ dev->name, __FUNCTION__,
+ ei_status.dmaing, ei_status.irqlock);
+ return;
+ }
+
+ ei_status.dmaing |= 0x01;
+ ei_outb(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base+ NE_CMD);
+ ei_outb(sizeof(struct e8390_pkt_hdr), nic_base + EN0_RCNTLO);
+ ei_outb(0, nic_base + EN0_RCNTHI);
+ ei_outb(0, nic_base + EN0_RSARLO); /* On page boundary */
+ ei_outb(ring_page, nic_base + EN0_RSARHI);
+ ei_outb(E8390_RREAD+E8390_START, nic_base + NE_CMD);
+
+ if (ei_status.word16)
+ readsw(nic_base + NE_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr)>>1);
+ else
+ readsb(nic_base + NE_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr));
+
+ ei_outb(ENISR_RDC, nic_base + EN0_ISR); /* Ack intr. */
+ ei_status.dmaing &= ~0x01;
+
+ le16_to_cpus(&hdr->count);
+}
+
+
+/* Block input and output, similar to the Crynwr packet driver. If you
+ are porting to a new ethercard, look at the packet driver source for hints.
+ The NEx000 doesn't share the on-board packet memory -- you have to put
+ the packet out through the "remote DMA" dataport using ei_outb. */
+
+static void ax_block_input(struct net_device *dev, int count,
+ struct sk_buff *skb, int ring_offset)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ void __iomem *nic_base = ei_local->mem;
+ char *buf = skb->data;
+
+ if (ei_status.dmaing) {
+ printk(KERN_EMERG "%s: DMAing conflict in ax_block_input "
+ "[DMAstat:%d][irqlock:%d].\n",
+ dev->name, ei_status.dmaing, ei_status.irqlock);
+ return;
+ }
+
+ ei_status.dmaing |= 0x01;
+
+ ei_outb(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base+ NE_CMD);
+ ei_outb(count & 0xff, nic_base + EN0_RCNTLO);
+ ei_outb(count >> 8, nic_base + EN0_RCNTHI);
+ ei_outb(ring_offset & 0xff, nic_base + EN0_RSARLO);
+ ei_outb(ring_offset >> 8, nic_base + EN0_RSARHI);
+ ei_outb(E8390_RREAD+E8390_START, nic_base + NE_CMD);
+
+ if (ei_status.word16) {
+ readsw(nic_base + NE_DATAPORT, buf, count >> 1);
+ if (count & 0x01)
+ buf[count-1] = ei_inb(nic_base + NE_DATAPORT);
+
+ } else {
+ readsb(nic_base + NE_DATAPORT, buf, count);
+ }
+
+ ei_status.dmaing &= ~1;
+}
+
+static void ax_block_output(struct net_device *dev, int count,
+ const unsigned char *buf, const int start_page)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ void __iomem *nic_base = ei_local->mem;
+ unsigned long dma_start;
+
+ /* Round the count up for word writes. Do we need to do this?
+ What effect will an odd byte count have on the 8390?
+ I should check someday. */
+
+ if (ei_status.word16 && (count & 0x01))
+ count++;
+
+ /* This *shouldn't* happen. If it does, it's the last thing you'll see */
+ if (ei_status.dmaing) {
+ printk(KERN_EMERG "%s: DMAing conflict in %s."
+ "[DMAstat:%d][irqlock:%d]\n",
+ dev->name, __FUNCTION__,
+ ei_status.dmaing, ei_status.irqlock);
+ return;
+ }
+
+ ei_status.dmaing |= 0x01;
+ /* We should already be in page 0, but to be safe... */
+ ei_outb(E8390_PAGE0+E8390_START+E8390_NODMA, nic_base + NE_CMD);
+
+ ei_outb(ENISR_RDC, nic_base + EN0_ISR);
+
+ /* Now the normal output. */
+ ei_outb(count & 0xff, nic_base + EN0_RCNTLO);
+ ei_outb(count >> 8, nic_base + EN0_RCNTHI);
+ ei_outb(0x00, nic_base + EN0_RSARLO);
+ ei_outb(start_page, nic_base + EN0_RSARHI);
+
+ ei_outb(E8390_RWRITE+E8390_START, nic_base + NE_CMD);
+ if (ei_status.word16) {
+ writesw(nic_base + NE_DATAPORT, buf, count>>1);
+ } else {
+ writesb(nic_base + NE_DATAPORT, buf, count);
+ }
+
+ dma_start = jiffies;
+
+ while ((ei_inb(nic_base + EN0_ISR) & ENISR_RDC) == 0) {
+ if (jiffies - dma_start > 2*HZ/100) { /* 20ms */
+ printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name);
+ ax_reset_8390(dev);
+ ax_NS8390_init(dev,1);
+ break;
+ }
+ }
+
+ ei_outb(ENISR_RDC, nic_base + EN0_ISR); /* Ack intr. */
+ ei_status.dmaing &= ~0x01;
+ return;
+}
+
+/* definitions for accessing MII/EEPROM interface */
+
+#define AX_MEMR EI_SHIFT(0x14)
+#define AX_MEMR_MDC (1<<0)
+#define AX_MEMR_MDIR (1<<1)
+#define AX_MEMR_MDI (1<<2)
+#define AX_MEMR_MDO (1<<3)
+#define AX_MEMR_EECS (1<<4)
+#define AX_MEMR_EEI (1<<5)
+#define AX_MEMR_EEO (1<<6)
+#define AX_MEMR_EECLK (1<<7)
+
+/* ax_mii_ei_outbits
+ *
+ * write the specified set of bits to the phy
+*/
+
+static void
+ax_mii_ei_outbits(struct net_device *dev, unsigned int bits, int len)
+{
+ struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
+ void __iomem *memr_addr = (void __iomem *)dev->base_addr + AX_MEMR;
+ unsigned int memr;
+
+ /* clock low, data to output mode */
+ memr = ei_inb(memr_addr);
+ memr &= ~(AX_MEMR_MDC | AX_MEMR_MDIR);
+ ei_outb(memr, memr_addr);
+
+ for (len--; len >= 0; len--) {
+ if (bits & (1 << len))
+ memr |= AX_MEMR_MDO;
+ else
+ memr &= ~AX_MEMR_MDO;
+
+ ei_outb(memr, memr_addr);
+
+ /* clock high */
+
+ ei_outb(memr | AX_MEMR_MDC, memr_addr);
+ udelay(1);
+
+ /* clock low */
+ ei_outb(memr, memr_addr);
+ }
+
+ /* leaves the clock line low, mdir input */
+ memr |= AX_MEMR_MDIR;
+ ei_outb(memr, (void __iomem *)dev->base_addr + AX_MEMR);
+}
+
+/* ax_phy_ei_inbits
+ *
+ * read a specified number of bits from the phy
+*/
+
+static unsigned int
+ax_phy_ei_inbits(struct net_device *dev, int no)
+{
+ struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
+ void __iomem *memr_addr = (void __iomem *)dev->base_addr + AX_MEMR;
+ unsigned int memr;
+ unsigned int result = 0;
+
+ /* clock low, data to input mode */
+ memr = ei_inb(memr_addr);
+ memr &= ~AX_MEMR_MDC;
+ memr |= AX_MEMR_MDIR;
+ ei_outb(memr, memr_addr);
+
+ for (no--; no >= 0; no--) {
+ ei_outb(memr | AX_MEMR_MDC, memr_addr);
+
+ udelay(1);
+
+ if (ei_inb(memr_addr) & AX_MEMR_MDI)
+ result |= (1<<no);
+
+ ei_outb(memr, memr_addr);
+ }
+
+ return result;
+}
+
+/* ax_phy_issueaddr
+ *
+ * use the low level bit shifting routines to send the address
+ * and command to the specified phy
+*/
+
+static void
+ax_phy_issueaddr(struct net_device *dev, int phy_addr, int reg, int opc)
+{
+ if (phy_debug)
+ pr_debug("%s: dev %p, %04x, %04x, %d\n",
+ __FUNCTION__, dev, phy_addr, reg, opc);
+
+ ax_mii_ei_outbits(dev, 0x3f, 6); /* pre-amble */
+ ax_mii_ei_outbits(dev, 1, 2); /* frame-start */
+ ax_mii_ei_outbits(dev, opc, 2); /* op code */
+ ax_mii_ei_outbits(dev, phy_addr, 5); /* phy address */
+ ax_mii_ei_outbits(dev, reg, 5); /* reg address */
+}
+
+static int
+ax_phy_read(struct net_device *dev, int phy_addr, int reg)
+{
+ struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
+ unsigned long flags;
+ unsigned int result;
+
+ spin_lock_irqsave(&ei_local->page_lock, flags);
+
+ ax_phy_issueaddr(dev, phy_addr, reg, 2);
+
+ result = ax_phy_ei_inbits(dev, 17);
+ result &= ~(3<<16);
+
+ spin_unlock_irqrestore(&ei_local->page_lock, flags);
+
+ if (phy_debug)
+ pr_debug("%s: %04x.%04x => read %04x\n", __FUNCTION__,
+ phy_addr, reg, result);
+
+ return result;
+}
+
+static void
+ax_phy_write(struct net_device *dev, int phy_addr, int reg, int value)
+{
+ struct ei_device *ei = (struct ei_device *) netdev_priv(dev);
+ unsigned long flags;
+
+ printk(KERN_DEBUG "%s: %p, %04x, %04x %04x\n",
+ __FUNCTION__, dev, phy_addr, reg, value);
+
+ spin_lock_irqsave(&ei->page_lock, flags);
+
+ ax_phy_issueaddr(dev, phy_addr, reg, 1);
+ ax_mii_ei_outbits(dev, 2, 2); /* send TA */
+ ax_mii_ei_outbits(dev, value, 16);
+
+ spin_unlock_irqrestore(&ei->page_lock, flags);
+}
+
+static void ax_mii_expiry(unsigned long data)
+{
+ struct net_device *dev = (struct net_device *)data;
+ struct ax_device *ax = to_ax_dev(dev);
+ unsigned long flags;
+
+ spin_lock_irqsave(&ax->mii_lock, flags);
+ mii_check_media(&ax->mii, netif_msg_link(ax), 0);
+ spin_unlock_irqrestore(&ax->mii_lock, flags);
+
+ if (ax->running) {
+ ax->mii_timer.expires = jiffies + HZ*2;
+ add_timer(&ax->mii_timer);
+ }
+}
+
+static int ax_open(struct net_device *dev)
+{
+ struct ax_device *ax = to_ax_dev(dev);
+ struct ei_device *ei_local = netdev_priv(dev);
+ int ret;
+
+ dev_dbg(ax->dev, "%s: open\n", dev->name);
+
+ ret = request_irq(dev->irq, ax_ei_interrupt, 0, dev->name, dev);
+ if (ret)
+ return ret;
+
+ ret = ax_ei_open(dev);
+ if (ret)
+ return ret;
+
+ /* turn the phy on (if turned off) */
+
+ ei_outb(ax->plat->gpoc_val, ei_local->mem + EI_SHIFT(0x17));
+ ax->running = 1;
+
+ /* start the MII timer */
+
+ init_timer(&ax->mii_timer);
+
+ ax->mii_timer.expires = jiffies+1;
+ ax->mii_timer.data = (unsigned long) dev;
+ ax->mii_timer.function = ax_mii_expiry;
+
+ add_timer(&ax->mii_timer);
+
+ return 0;
+}
+
+static int ax_close(struct net_device *dev)
+{
+ struct ax_device *ax = to_ax_dev(dev);
+ struct ei_device *ei_local = netdev_priv(dev);
+
+ dev_dbg(ax->dev, "%s: close\n", dev->name);
+
+ /* turn the phy off */
+
+ ei_outb(ax->plat->gpoc_val | (1<<6),
+ ei_local->mem + EI_SHIFT(0x17));
+
+ ax->running = 0;
+ wmb();
+
+ del_timer_sync(&ax->mii_timer);
+ ax_ei_close(dev);
+
+ free_irq(dev->irq, dev);
+ return 0;
+}
+
+static int ax_ioctl(struct net_device *dev, struct ifreq *req, int cmd)
+{
+ struct ax_device *ax = to_ax_dev(dev);
+ unsigned long flags;
+ int rc;
+
+ if (!netif_running(dev))
+ return -EINVAL;
+
+ spin_lock_irqsave(&ax->mii_lock, flags);
+ rc = generic_mii_ioctl(&ax->mii, if_mii(req), cmd, NULL);
+ spin_unlock_irqrestore(&ax->mii_lock, flags);
+
+ return rc;
+}
+
+/* ethtool ops */
+
+static void ax_get_drvinfo(struct net_device *dev,
+ struct ethtool_drvinfo *info)
+{
+ struct ax_device *ax = to_ax_dev(dev);
+
+ strcpy(info->driver, DRV_NAME);
+ strcpy(info->version, DRV_VERSION);
+ strcpy(info->bus_info, ax->dev->name);
+}
+
+static int ax_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+ struct ax_device *ax = to_ax_dev(dev);
+ unsigned long flags;
+
+ spin_lock_irqsave(&ax->mii_lock, flags);
+ mii_ethtool_gset(&ax->mii, cmd);
+ spin_lock_irqsave(&ax->mii_lock, flags);
+
+ return 0;
+}
+
+static int ax_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+ struct ax_device *ax = to_ax_dev(dev);
+ unsigned long flags;
+ int rc;
+
+ spin_lock_irqsave(&ax->mii_lock, flags);
+ rc = mii_ethtool_sset(&ax->mii, cmd);
+ spin_lock_irqsave(&ax->mii_lock, flags);
+
+ return rc;
+}
+
+static int ax_nway_reset(struct net_device *dev)
+{
+ struct ax_device *ax = to_ax_dev(dev);
+ return mii_nway_restart(&ax->mii);
+}
+
+static u32 ax_get_link(struct net_device *dev)
+{
+ struct ax_device *ax = to_ax_dev(dev);
+ return mii_link_ok(&ax->mii);
+}
+
+static const struct ethtool_ops ax_ethtool_ops = {
+ .get_drvinfo = ax_get_drvinfo,
+ .get_settings = ax_get_settings,
+ .set_settings = ax_set_settings,
+ .nway_reset = ax_nway_reset,
+ .get_link = ax_get_link,
+ .get_perm_addr = ethtool_op_get_perm_addr,
+};
+
+/* setup code */
+
+static void ax_initial_setup(struct net_device *dev, struct ei_device *ei_local)
+{
+ void __iomem *ioaddr = ei_local->mem;
+ struct ax_device *ax = to_ax_dev(dev);
+
+ /* Select page 0*/
+ ei_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, ioaddr + E8390_CMD);
+
+ /* set to byte access */
+ ei_outb(ax->plat->dcr_val & ~1, ioaddr + EN0_DCFG);
+ ei_outb(ax->plat->gpoc_val, ioaddr + EI_SHIFT(0x17));
+}
+
+/* ax_init_dev
+ *
+ * initialise the specified device, taking care to note the MAC
+ * address it may already have (if configured), ensure
+ * the device is ready to be used by lib8390.c and registerd with
+ * the network layer.
+ */
+
+static int ax_init_dev(struct net_device *dev, int first_init)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ struct ax_device *ax = to_ax_dev(dev);
+ void __iomem *ioaddr = ei_local->mem;
+ unsigned int start_page;
+ unsigned int stop_page;
+ int ret;
+ int i;
+
+ ret = ax_initial_check(dev);
+ if (ret)
+ goto err_out;
+
+ /* setup goes here */
+
+ ax_initial_setup(dev, ei_local);
+
+ /* read the mac from the card prom if we need it */
+
+ if (first_init && ax->plat->flags & AXFLG_HAS_EEPROM) {
+ unsigned char SA_prom[32];
+
+ for(i = 0; i < sizeof(SA_prom); i+=2) {
+ SA_prom[i] = ei_inb(ioaddr + NE_DATAPORT);
+ SA_prom[i+1] = ei_inb(ioaddr + NE_DATAPORT);
+ }
+
+ if (ax->plat->wordlength == 2)
+ for (i = 0; i < 16; i++)
+ SA_prom[i] = SA_prom[i+i];
+
+ memcpy(dev->dev_addr, SA_prom, 6);
+ }
+
+ if (ax->plat->wordlength == 2) {
+ /* We must set the 8390 for word mode. */
+ ei_outb(ax->plat->dcr_val, ei_local->mem + EN0_DCFG);
+ start_page = NESM_START_PG;
+ stop_page = NESM_STOP_PG;
+ } else {
+ start_page = NE1SM_START_PG;
+ stop_page = NE1SM_STOP_PG;
+ }
+
+ /* load the mac-address from the device if this is the
+ * first time we've initialised */
+
+ if (first_init && ax->plat->flags & AXFLG_MAC_FROMDEV) {
+ ei_outb(E8390_NODMA + E8390_PAGE1 + E8390_STOP,
+ ei_local->mem + E8390_CMD); /* 0x61 */
+
+ for (i = 0 ; i < ETHER_ADDR_LEN ; i++)
+ dev->dev_addr[i] = ei_inb(ioaddr + EN1_PHYS_SHIFT(i));
+ }
+
+ ax_reset_8390(dev);
+
+ ei_status.name = "AX88796";
+ ei_status.tx_start_page = start_page;
+ ei_status.stop_page = stop_page;
+ ei_status.word16 = (ax->plat->wordlength == 2);
+ ei_status.rx_start_page = start_page + TX_PAGES;
+
+#ifdef PACKETBUF_MEMSIZE
+ /* Allow the packet buffer size to be overridden by know-it-alls. */
+ ei_status.stop_page = ei_status.tx_start_page + PACKETBUF_MEMSIZE;
+#endif
+
+ ei_status.reset_8390 = &ax_reset_8390;
+ ei_status.block_input = &ax_block_input;
+ ei_status.block_output = &ax_block_output;
+ ei_status.get_8390_hdr = &ax_get_8390_hdr;
+ ei_status.priv = 0;
+
+ dev->open = ax_open;
+ dev->stop = ax_close;
+ dev->do_ioctl = ax_ioctl;
+ dev->ethtool_ops = &ax_ethtool_ops;
+
+ ax->msg_enable = NETIF_MSG_LINK;
+ ax->mii.phy_id_mask = 0x1f;
+ ax->mii.reg_num_mask = 0x1f;
+ ax->mii.phy_id = 0x10; /* onboard phy */
+ ax->mii.force_media = 0;
+ ax->mii.full_duplex = 0;
+ ax->mii.mdio_read = ax_phy_read;
+ ax->mii.mdio_write = ax_phy_write;
+ ax->mii.dev = dev;
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ dev->poll_controller = ax_ei_poll;
+#endif
+ ax_NS8390_init(dev, 0);
+
+ if (first_init) {
+ printk("AX88796: %dbit, irq %d, %lx, MAC: ",
+ ei_status.word16 ? 16:8, dev->irq, dev->base_addr);
+
+ for (i = 0; i < ETHER_ADDR_LEN; i++)
+ printk("%2.2x%c", dev->dev_addr[i],
+ (i < (ETHER_ADDR_LEN-1) ? ':' : ' '));
+
+ printk("\n");
+ }
+
+ ret = register_netdev(dev);
+ if (ret)
+ goto out_irq;
+
+ return 0;
+
+ out_irq:
+ /* cleanup irq */
+ free_irq(dev->irq, dev);
+ err_out:
+ return ret;
+}
+
+static int ax_remove(struct platform_device *_dev)
+{
+ struct net_device *dev = platform_get_drvdata(_dev);
+ struct ax_device *ax;
+
+ ax = to_ax_dev(dev);
+
+ unregister_netdev(dev);
+ free_irq(dev->irq, dev);
+
+ iounmap(ei_status.mem);
+ release_resource(ax->mem);
+ kfree(ax->mem);
+
+ if (ax->map2) {
+ iounmap(ax->map2);
+ release_resource(ax->mem2);
+ kfree(ax->mem2);
+ }
+
+ free_netdev(dev);
+
+ return 0;
+}
+
+/* ax_probe
+ *
+ * This is the entry point when the platform device system uses to
+ * notify us of a new device to attach to. Allocate memory, find
+ * the resources and information passed, and map the necessary registers.
+*/
+
+static int ax_probe(struct platform_device *pdev)
+{
+ struct net_device *dev;
+ struct ax_device *ax;
+ struct resource *res;
+ size_t size;
+ int ret;
+
+ dev = ax__alloc_ei_netdev(sizeof(struct ax_device));
+ if (dev == NULL)
+ return -ENOMEM;
+
+ /* ok, let's setup our device */
+ ax = to_ax_dev(dev);
+
+ memset(ax, 0, sizeof(struct ax_device));
+
+ spin_lock_init(&ax->mii_lock);
+
+ ax->dev = pdev;
+ ax->plat = pdev->dev.platform_data;
+ platform_set_drvdata(pdev, dev);
+
+ ei_status.rxcr_base = ax->plat->rcr_val;
+
+ /* find the platform resources */
+
+ dev->irq = platform_get_irq(pdev, 0);
+ if (dev->irq < 0) {
+ dev_err(&pdev->dev, "no IRQ specified\n");
+ ret = -ENXIO;
+ goto exit_mem;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res == NULL) {
+ dev_err(&pdev->dev, "no MEM specified\n");
+ ret = -ENXIO;
+ goto exit_mem;
+ }
+
+ size = (res->end - res->start) + 1;
+
+ /* setup the register offsets from either the platform data
+ * or by using the size of the resource provided */
+
+ if (ax->plat->reg_offsets)
+ ei_status.reg_offset = ax->plat->reg_offsets;
+ else {
+ ei_status.reg_offset = ax->reg_offsets;
+ for (ret = 0; ret < 0x18; ret++)
+ ax->reg_offsets[ret] = (size / 0x18) * ret;
+ }
+
+ ax->mem = request_mem_region(res->start, size, pdev->name);
+ if (ax->mem == NULL) {
+ dev_err(&pdev->dev, "cannot reserve registers\n");
+ ret = -ENXIO;
+ goto exit_mem;
+ }
+
+ ei_status.mem = ioremap(res->start, size);
+ dev->base_addr = (long)ei_status.mem;
+
+ if (ei_status.mem == NULL) {
+ dev_err(&pdev->dev, "Cannot ioremap area (%08zx,%08zx)\n",
+ res->start, res->end);
+
+ ret = -ENXIO;
+ goto exit_req;
+ }
+
+ /* look for reset area */
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (res == NULL) {
+ if (!ax->plat->reg_offsets) {
+ for (ret = 0; ret < 0x20; ret++)
+ ax->reg_offsets[ret] = (size / 0x20) * ret;
+ }
+
+ ax->map2 = NULL;
+ } else {
+ size = (res->end - res->start) + 1;
+
+ ax->mem2 = request_mem_region(res->start, size, pdev->name);
+ if (ax->mem == NULL) {
+ dev_err(&pdev->dev, "cannot reserve registers\n");
+ ret = -ENXIO;
+ goto exit_mem1;
+ }
+
+ ax->map2 = ioremap(res->start, size);
+ if (ax->map2 == NULL) {
+ dev_err(&pdev->dev, "cannot map reset register");
+ ret = -ENXIO;
+ goto exit_mem2;
+ }
+
+ ei_status.reg_offset[0x1f] = ax->map2 - ei_status.mem;
+ }
+
+ /* got resources, now initialise and register device */
+
+ ret = ax_init_dev(dev, 1);
+ if (!ret)
+ return 0;
+
+ if (ax->map2 == NULL)
+ goto exit_mem1;
+
+ iounmap(ax->map2);
+
+ exit_mem2:
+ release_resource(ax->mem2);
+ kfree(ax->mem2);
+
+ exit_mem1:
+ iounmap(ei_status.mem);
+
+ exit_req:
+ release_resource(ax->mem);
+ kfree(ax->mem);
+
+ exit_mem:
+ free_netdev(dev);
+
+ return ret;
+}
+
+/* suspend and resume */
+
+#ifdef CONFIG_PM
+static int ax_suspend(struct platform_device *dev, pm_message_t state)
+{
+ struct net_device *ndev = platform_get_drvdata(dev);
+ struct ax_device *ax = to_ax_dev(ndev);
+
+ ax->resume_open = ax->running;
+
+ netif_device_detach(ndev);
+ ax_close(ndev);
+
+ return 0;
+}
+
+static int ax_resume(struct platform_device *pdev)
+{
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct ax_device *ax = to_ax_dev(ndev);
+
+ ax_initial_setup(ndev, netdev_priv(ndev));
+ ax_NS8390_init(ndev, ax->resume_open);
+ netif_device_attach(ndev);
+
+ if (ax->resume_open)
+ ax_open(ndev);
+
+ return 0;
+}
+
+#else
+#define ax_suspend NULL
+#define ax_resume NULL
+#endif
+
+static struct platform_driver axdrv = {
+ .driver = {
+ .name = "ax88796",
+ .owner = THIS_MODULE,
+ },
+ .probe = ax_probe,
+ .remove = ax_remove,
+ .suspend = ax_suspend,
+ .resume = ax_resume,
+};
+
+static int __init axdrv_init(void)
+{
+ return platform_driver_register(&axdrv);
+}
+
+static void __exit axdrv_exit(void)
+{
+ platform_driver_unregister(&axdrv);
+}
+
+module_init(axdrv_init);
+module_exit(axdrv_exit);
+
+MODULE_DESCRIPTION("AX88796 10/100 Ethernet platform driver");
+MODULE_AUTHOR("Ben Dooks, <ben@simtec.co.uk>");
+MODULE_LICENSE("GPL v2");
diff --git a/include/net/ax88796.h b/include/net/ax88796.h
new file mode 100644
index 0000000..ee786a0
--- /dev/null
+++ b/include/net/ax88796.h
@@ -0,0 +1,27 @@
+/* include/net/ax88796.h
+ *
+ * Copyright 2005 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#ifndef __NET_AX88796_PLAT_H
+#define __NET_AX88796_PLAT_H
+
+#define AXFLG_HAS_EEPROM (1<<0)
+#define AXFLG_MAC_FROMDEV (1<<1) /* device already has MAC */
+
+struct ax_plat_data {
+ unsigned int flags;
+ unsigned char wordlength; /* 1 or 2 */
+ unsigned char dcr_val; /* default value for DCR */
+ unsigned char rcr_val; /* default value for RCR */
+ unsigned char gpoc_val; /* default value for GPOC */
+ u32 *reg_offsets; /* register offsets */
+};
+
+#endif /* __NET_AX88796_PLAT_H */