[BNX2]: Fix default WoL setting.
Change the default WoL setting to match the NVRAM's setting. It
always defaulted to WoL disabled before and caused a lot of confusion
for users.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c
index 21493e0..574d043 100644
--- a/drivers/net/bnx2.c
+++ b/drivers/net/bnx2.c
@@ -6569,8 +6569,11 @@
if (i != 2)
bp->fw_version[j++] = '.';
}
- if (REG_RD_IND(bp, bp->shmem_base + BNX2_PORT_FEATURE) &
- BNX2_PORT_FEATURE_ASF_ENABLED) {
+ reg = REG_RD_IND(bp, bp->shmem_base + BNX2_PORT_FEATURE);
+ if (reg & BNX2_PORT_FEATURE_WOL_ENABLED)
+ bp->wol = 1;
+
+ if (reg & BNX2_PORT_FEATURE_ASF_ENABLED) {
bp->flags |= ASF_ENABLE_FLAG;
for (i = 0; i < 30; i++) {
@@ -6640,11 +6643,14 @@
bp->phy_port = PORT_TP;
if (bp->phy_flags & PHY_SERDES_FLAG) {
bp->phy_port = PORT_FIBRE;
- bp->flags |= NO_WOL_FLAG;
+ reg = REG_RD_IND(bp, bp->shmem_base +
+ BNX2_SHARED_HW_CFG_CONFIG);
+ if (!(reg & BNX2_SHARED_HW_CFG_GIG_LINK_ON_VAUX)) {
+ bp->flags |= NO_WOL_FLAG;
+ bp->wol = 0;
+ }
if (CHIP_NUM(bp) != CHIP_NUM_5706) {
bp->phy_addr = 2;
- reg = REG_RD_IND(bp, bp->shmem_base +
- BNX2_SHARED_HW_CFG_CONFIG);
if (reg & BNX2_SHARED_HW_CFG_PHY_2_5G)
bp->phy_flags |= PHY_2_5G_CAPABLE_FLAG;
}
@@ -6659,8 +6665,10 @@
if ((CHIP_ID(bp) == CHIP_ID_5708_A0) ||
(CHIP_ID(bp) == CHIP_ID_5708_B0) ||
- (CHIP_ID(bp) == CHIP_ID_5708_B1))
+ (CHIP_ID(bp) == CHIP_ID_5708_B1)) {
bp->flags |= NO_WOL_FLAG;
+ bp->wol = 0;
+ }
if (CHIP_ID(bp) == CHIP_ID_5706_A0) {
bp->tx_quick_cons_trip_int =
diff --git a/drivers/net/bnx2.h b/drivers/net/bnx2.h
index 56c190f..1dce0d1 100644
--- a/drivers/net/bnx2.h
+++ b/drivers/net/bnx2.h
@@ -6908,6 +6908,7 @@
#define BNX2_SHARED_HW_CFG_LED_MODE_MAC 0
#define BNX2_SHARED_HW_CFG_LED_MODE_GPHY1 0x100
#define BNX2_SHARED_HW_CFG_LED_MODE_GPHY2 0x200
+#define BNX2_SHARED_HW_CFG_GIG_LINK_ON_VAUX 0x8000
#define BNX2_SHARED_HW_CFG_CONFIG2 0x00000040
#define BNX2_SHARED_HW_CFG2_NVM_SIZE_MASK 0x00fff000