mwl8k: handle 5 GHz legacy rate bitmaps in firmware commands
Whenever mac80211 gives us a legacy rate bitmap in the context of the
5 GHz band, we need to remember to shift the bitmap left by 5 positions
before giving it to the firmware, as the firmware follows the bitmap
bit assignment of the 2.4 GHz rate table even if we're on the 5 GHz
band, and the 2.4 GHz rate table includes five non-OFDM rates at the
start that are not valid in the 5 GHz band.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c
index cc2ce61..e370245 100644
--- a/drivers/net/wireless/mwl8k.c
+++ b/drivers/net/wireless/mwl8k.c
@@ -2836,6 +2836,7 @@
struct ieee80211_sta *sta)
{
struct mwl8k_cmd_set_new_stn *cmd;
+ u32 rates;
int rc;
cmd = kzalloc(sizeof(*cmd), GFP_KERNEL);
@@ -2848,7 +2849,11 @@
memcpy(cmd->mac_addr, sta->addr, ETH_ALEN);
cmd->stn_id = cpu_to_le16(sta->aid);
cmd->action = cpu_to_le16(MWL8K_STA_ACTION_ADD);
- cmd->legacy_rates = cpu_to_le32(sta->supp_rates[IEEE80211_BAND_2GHZ]);
+ if (hw->conf.channel->band == IEEE80211_BAND_2GHZ)
+ rates = sta->supp_rates[IEEE80211_BAND_2GHZ];
+ else
+ rates = sta->supp_rates[IEEE80211_BAND_5GHZ] << 5;
+ cmd->legacy_rates = cpu_to_le32(rates);
if (sta->ht_cap.ht_supported) {
cmd->ht_rates[0] = sta->ht_cap.mcs.rx_mask[0];
cmd->ht_rates[1] = sta->ht_cap.mcs.rx_mask[1];
@@ -2972,6 +2977,7 @@
{
struct mwl8k_cmd_update_stadb *cmd;
struct peer_capability_info *p;
+ u32 rates;
int rc;
cmd = kzalloc(sizeof(*cmd), GFP_KERNEL);
@@ -2990,8 +2996,11 @@
p->ht_caps = sta->ht_cap.cap;
p->extended_ht_caps = (sta->ht_cap.ampdu_factor & 3) |
((sta->ht_cap.ampdu_density & 7) << 2);
- legacy_rate_mask_to_array(p->legacy_rates,
- sta->supp_rates[IEEE80211_BAND_2GHZ]);
+ if (hw->conf.channel->band == IEEE80211_BAND_2GHZ)
+ rates = sta->supp_rates[IEEE80211_BAND_2GHZ];
+ else
+ rates = sta->supp_rates[IEEE80211_BAND_5GHZ] << 5;
+ legacy_rate_mask_to_array(p->legacy_rates, rates);
memcpy(p->ht_rates, sta->ht_cap.mcs.rx_mask, 16);
p->interop = 1;
p->amsdu_enabled = 0;
@@ -3345,7 +3354,12 @@
goto out;
}
- ap_legacy_rates = ap->supp_rates[IEEE80211_BAND_2GHZ];
+ if (hw->conf.channel->band == IEEE80211_BAND_2GHZ) {
+ ap_legacy_rates = ap->supp_rates[IEEE80211_BAND_2GHZ];
+ } else {
+ ap_legacy_rates =
+ ap->supp_rates[IEEE80211_BAND_5GHZ] << 5;
+ }
memcpy(ap_mcs_rates, ap->ht_cap.mcs.rx_mask, 16);
rcu_read_unlock();
@@ -3422,7 +3436,13 @@
* beacons will always go out at 1 Mb/s).
*/
idx = ffs(vif->bss_conf.basic_rates);
- rate = idx ? mwl8k_rates_24[idx - 1].hw_value : 2;
+ if (idx)
+ idx--;
+
+ if (hw->conf.channel->band == IEEE80211_BAND_2GHZ)
+ rate = mwl8k_rates_24[idx].hw_value;
+ else
+ rate = mwl8k_rates_50[idx].hw_value;
mwl8k_cmd_use_fixed_rate_ap(hw, rate, rate);
}