Merge master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
scc_pata: PIO fixes
piix/slc90e66: fix PIO1 handling in ->speedproc method (take 2)
jmicron: PIO fixes
it8213: PIO fixes (take 2)
cs5535: PIO fixes
cs5520: fix PIO auto-tuning in ->ide_dma_check method
drivers/scsi/ide-scsi.c: kmalloc + memset conversion to kzalloc
drivers/ide/arm/icside.c: kmalloc + memset conversion to kzalloc
ide: eliminate warnings in ide-tape.c
ide: fix runtogether printk's in cmd64x IDE driver
sis5513: Add FSC Amilo A1630 PCI subvendor/dev to laptops
alim15x3: Correct HP detect
ide: Fix an overrun found in the CS5535 IDE driver
diff --git a/arch/frv/mb93090-mb00/pci-vdk.c b/arch/frv/mb93090-mb00/pci-vdk.c
index 0b581e3..6d51f13 100644
--- a/arch/frv/mb93090-mb00/pci-vdk.c
+++ b/arch/frv/mb93090-mb00/pci-vdk.c
@@ -400,7 +400,8 @@
__reg_MB86943_pci_sl_mem_base = __region_CS2 + 0x08000000;
mb();
- *(volatile unsigned long *)(__region_CS2+0x01300014) == 1;
+ /* enable PCI arbitration */
+ __reg_MB86943_pci_arbiter = MB86943_PCIARB_EN;
ioport_resource.start = (__reg_MB86943_sl_pci_io_base << 9) & 0xfffffc00;
ioport_resource.end = (__reg_MB86943_sl_pci_io_range << 9) | 0x3ff;
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index ad07086..a78832e 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -890,37 +890,46 @@
}
#ifdef CONFIG_PM
-static struct dmi_system_id piix_broken_suspend_dmi_table[] = {
- {
- .ident = "TECRA M5",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
- DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M5"),
+static int piix_broken_suspend(void)
+{
+ static struct dmi_system_id sysids[] = {
+ {
+ .ident = "TECRA M5",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M5"),
+ },
},
- },
- {
- .ident = "Satellite U200",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
- DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U200"),
+ {
+ .ident = "Satellite U205",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U205"),
+ },
},
- },
- {
- .ident = "Satellite U205",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
- DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U205"),
+ {
+ .ident = "Portege M500",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "PORTEGE M500"),
+ },
},
- },
- {
- .ident = "Portege M500",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
- DMI_MATCH(DMI_PRODUCT_NAME, "PORTEGE M500"),
- },
- },
- { }
-};
+ { }
+ };
+ static const char *oemstrs[] = {
+ "Tecra M3,",
+ };
+ int i;
+
+ if (dmi_check_system(sysids))
+ return 1;
+
+ for (i = 0; i < ARRAY_SIZE(oemstrs); i++)
+ if (dmi_find_device(DMI_DEV_TYPE_OEM_STRING, oemstrs[i], NULL))
+ return 1;
+
+ return 0;
+}
static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
@@ -937,8 +946,7 @@
* cycles and power trying to do something to the sleeping
* beauty.
*/
- if (dmi_check_system(piix_broken_suspend_dmi_table) &&
- mesg.event == PM_EVENT_SUSPEND) {
+ if (piix_broken_suspend() && mesg.event == PM_EVENT_SUSPEND) {
pci_save_state(pdev);
/* mark its power state as "unknown", since we don't
@@ -973,10 +981,10 @@
pci_restore_state(pdev);
/* PCI device wasn't disabled during suspend. Use
- * __pci_reenable_device() to avoid affecting the
- * enable count.
+ * pci_reenable_device() to avoid affecting the enable
+ * count.
*/
- rc = __pci_reenable_device(pdev);
+ rc = pci_reenable_device(pdev);
if (rc)
dev_printk(KERN_ERR, &pdev->dev, "failed to enable "
"device after resume (%d)\n", rc);
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 6001aae..60e78be 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3788,6 +3788,7 @@
{ "WDC WD740ADFD-00NLR1", NULL, ATA_HORKAGE_NONCQ, },
{ "FUJITSU MHV2080BH", "00840028", ATA_HORKAGE_NONCQ, },
{ "ST9160821AS", "3.CLF", ATA_HORKAGE_NONCQ, },
+ { "SAMSUNG HD401LJ", "ZZ100-15", ATA_HORKAGE_NONCQ, },
/* Devices with NCQ limits */
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index 6c289c7..1cce219 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -573,6 +573,10 @@
struct pci_dev *pdev = to_pci_dev(gdev);
int i, rc;
+ /* No BAR4 allocation: No DMA */
+ if (pci_resource_start(pdev, 4) == 0)
+ return 0;
+
/* TODO: If we get no DMA mask we should fall back to PIO */
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
index dc443e7..e34b632 100644
--- a/drivers/ata/pata_cmd64x.c
+++ b/drivers/ata/pata_cmd64x.c
@@ -31,7 +31,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_cmd64x"
-#define DRV_VERSION "0.2.3"
+#define DRV_VERSION "0.2.4"
/*
* CMD64x specific registers definition.
@@ -397,7 +397,7 @@
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA1,
+ .udma_mask = ATA_UDMA2,
.port_ops = &cmd64x_port_ops
},
{ /* CMD 646 rev 1 */
@@ -412,7 +412,7 @@
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA2,
+ .udma_mask = ATA_UDMA4,
.port_ops = &cmd648_port_ops
},
{ /* CMD 649 */
@@ -420,7 +420,7 @@
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA3,
+ .udma_mask = ATA_UDMA5,
.port_ops = &cmd648_port_ops
}
};
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index 9a829a7..66bd0e8 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -2,6 +2,7 @@
* pata_sis.c - SiS ATA driver
*
* (C) 2005 Red Hat <alan@redhat.com>
+ * (C) 2007 Bartlomiej Zolnierkiewicz
*
* Based upon linux/drivers/ide/pci/sis5513.c
* Copyright (C) 1999-2000 Andre Hedrick <andre@linux-ide.org>
@@ -35,7 +36,7 @@
#include "sis.h"
#define DRV_NAME "pata_sis"
-#define DRV_VERSION "0.5.1"
+#define DRV_VERSION "0.5.2"
struct sis_chipset {
u16 device; /* PCI host ID */
@@ -237,7 +238,7 @@
}
/**
- * sis_100_set_pioode - Initialize host controller PATA PIO timings
+ * sis_100_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
* @adev: Device we are configuring for.
*
@@ -262,7 +263,7 @@
}
/**
- * sis_133_set_pioode - Initialize host controller PATA PIO timings
+ * sis_133_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
* @adev: Device we are configuring for.
*
@@ -334,7 +335,7 @@
int drive_pci = sis_old_port_base(adev);
u16 timing;
- const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
+ const u16 mwdma_bits[] = { 0x008, 0x302, 0x301 };
const u16 udma_bits[] = { 0xE000, 0xC000, 0xA000 };
pci_read_config_word(pdev, drive_pci, &timing);
@@ -342,15 +343,15 @@
if (adev->dma_mode < XFER_UDMA_0) {
/* bits 3-0 hold recovery timing bits 8-10 active timing and
the higer bits are dependant on the device */
- timing &= ~ 0x870F;
+ timing &= ~0x870F;
timing |= mwdma_bits[speed];
- pci_write_config_word(pdev, drive_pci, timing);
} else {
/* Bit 15 is UDMA on/off, bit 13-14 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
timing &= ~0x6000;
timing |= udma_bits[speed];
}
+ pci_write_config_word(pdev, drive_pci, timing);
}
/**
@@ -373,7 +374,7 @@
int drive_pci = sis_old_port_base(adev);
u16 timing;
- const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
+ const u16 mwdma_bits[] = { 0x008, 0x302, 0x301 };
const u16 udma_bits[] = { 0xF000, 0xD000, 0xB000, 0xA000, 0x9000};
pci_read_config_word(pdev, drive_pci, &timing);
@@ -432,8 +433,7 @@
* @adev: Device to program
*
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
- * Handles early SiS 961 bridges. Supports MWDMA as well unlike
- * the old ide/pci driver.
+ * Handles early SiS 961 bridges.
*
* LOCKING:
* None (inherited from caller).
@@ -467,8 +467,6 @@
* @adev: Device to program
*
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
- * Handles early SiS 961 bridges. Supports MWDMA as well unlike
- * the old ide/pci driver.
*
* LOCKING:
* None (inherited from caller).
diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c
index 8e58ea3..004bc24 100644
--- a/drivers/pci/pci-driver.c
+++ b/drivers/pci/pci-driver.c
@@ -310,7 +310,7 @@
/* restore the PCI config space */
pci_restore_state(pci_dev);
/* if the device was enabled before suspend, reenable */
- retval = __pci_reenable_device(pci_dev);
+ retval = pci_reenable_device(pci_dev);
/* if the device was busmaster before the suspend, make it busmaster again */
if (pci_dev->is_busmaster)
pci_set_master(pci_dev);
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index 1ee9cd9..37c00f6 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -695,14 +695,13 @@
}
/**
- * __pci_reenable_device - Resume abandoned device
+ * pci_reenable_device - Resume abandoned device
* @dev: PCI device to be resumed
*
* Note this function is a backend of pci_default_resume and is not supposed
* to be called by normal code, write proper resume handler and use it instead.
*/
-int
-__pci_reenable_device(struct pci_dev *dev)
+int pci_reenable_device(struct pci_dev *dev)
{
if (atomic_read(&dev->enable_cnt))
return do_pci_enable_device(dev, (1 << PCI_NUM_RESOURCES) - 1);
@@ -1604,7 +1603,7 @@
device_initcall(pci_init);
EXPORT_SYMBOL_GPL(pci_restore_bars);
-EXPORT_SYMBOL(__pci_reenable_device);
+EXPORT_SYMBOL(pci_reenable_device);
EXPORT_SYMBOL(pci_enable_device_bars);
EXPORT_SYMBOL(pci_enable_device);
EXPORT_SYMBOL(pcim_enable_device);
diff --git a/include/asm-avr32/bug.h b/include/asm-avr32/bug.h
index afdcd79..331d45b 100644
--- a/include/asm-avr32/bug.h
+++ b/include/asm-avr32/bug.h
@@ -57,7 +57,7 @@
#define WARN_ON(condition) \
({ \
- typeof(condition) __ret_warn_on = (condition); \
+ int __ret_warn_on = !!(condition); \
if (unlikely(__ret_warn_on)) \
_BUG_OR_WARN(BUGFLAG_WARNING); \
unlikely(__ret_warn_on); \
diff --git a/include/asm-frv/mb86943a.h b/include/asm-frv/mb86943a.h
index b89fd0b..e87ef92 100644
--- a/include/asm-frv/mb86943a.h
+++ b/include/asm-frv/mb86943a.h
@@ -36,4 +36,7 @@
#define __reg_MB86943_pci_sl_io_base *(volatile uint32_t *) (__region_CS1 + 0x70)
#define __reg_MB86943_pci_sl_mem_base *(volatile uint32_t *) (__region_CS1 + 0x78)
+#define __reg_MB86943_pci_arbiter *(volatile uint32_t *) (__region_CS2 + 0x01300014)
+#define MB86943_PCIARB_EN 0x00000001
+
#endif /* _ASM_MB86943A_H */
diff --git a/include/asm-parisc/bug.h b/include/asm-parisc/bug.h
index 83ba510..8cfc553 100644
--- a/include/asm-parisc/bug.h
+++ b/include/asm-parisc/bug.h
@@ -74,7 +74,7 @@
#define WARN_ON(x) ({ \
- typeof(x) __ret_warn_on = (x); \
+ int __ret_warn_on = !!(x); \
if (__builtin_constant_p(__ret_warn_on)) { \
if (__ret_warn_on) \
__WARN(); \
diff --git a/include/asm-s390/bug.h b/include/asm-s390/bug.h
index 838684d..384e362 100644
--- a/include/asm-s390/bug.h
+++ b/include/asm-s390/bug.h
@@ -50,7 +50,7 @@
#define BUG() __EMIT_BUG(0)
#define WARN_ON(x) ({ \
- typeof(x) __ret_warn_on = (x); \
+ int __ret_warn_on = !!(x); \
if (__builtin_constant_p(__ret_warn_on)) { \
if (__ret_warn_on) \
__EMIT_BUG(BUGFLAG_WARNING); \
diff --git a/include/asm-sh/bug.h b/include/asm-sh/bug.h
index 46f925c..a78d482 100644
--- a/include/asm-sh/bug.h
+++ b/include/asm-sh/bug.h
@@ -61,7 +61,7 @@
} while (0)
#define WARN_ON(x) ({ \
- typeof(x) __ret_warn_on = (x); \
+ int __ret_warn_on = !!(x); \
if (__builtin_constant_p(__ret_warn_on)) { \
if (__ret_warn_on) \
__WARN(); \
diff --git a/include/linux/pci.h b/include/linux/pci.h
index d8f8a3a..e7d8d4e 100644
--- a/include/linux/pci.h
+++ b/include/linux/pci.h
@@ -534,7 +534,7 @@
int __must_check pci_enable_device(struct pci_dev *dev);
int __must_check pci_enable_device_bars(struct pci_dev *dev, int mask);
-int __must_check __pci_reenable_device(struct pci_dev *);
+int __must_check pci_reenable_device(struct pci_dev *);
int __must_check pcim_enable_device(struct pci_dev *pdev);
void pcim_pin_device(struct pci_dev *pdev);
diff --git a/kernel/irq/resend.c b/kernel/irq/resend.c
index 5bfeaed..c382727 100644
--- a/kernel/irq/resend.c
+++ b/kernel/irq/resend.c
@@ -62,6 +62,15 @@
*/
desc->chip->enable(irq);
+ /*
+ * Temporary hack to figure out more about the problem, which
+ * is causing the ancient network cards to die.
+ */
+ if (desc->handle_irq != handle_edge_irq) {
+ WARN_ON_ONCE(1);
+ return;
+ }
+
if ((status & (IRQ_PENDING | IRQ_REPLAY)) == IRQ_PENDING) {
desc->status = (status & ~IRQ_PENDING) | IRQ_REPLAY;