| /* |
| * RTL8XXXU mac80211 USB driver |
| * |
| * Copyright (c) 2014 - 2015 Jes Sorensen <Jes.Sorensen@redhat.com> |
| * |
| * Portions, notably calibration code: |
| * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved. |
| * |
| * This driver was written as a replacement for the vendor provided |
| * rtl8723au driver. As the Realtek 8xxx chips are very similar in |
| * their programming interface, I have started adding support for |
| * additional 8xxx chips like the 8192cu, 8188cus, etc. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of version 2 of the GNU General Public License as |
| * published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, but WITHOUT |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for |
| * more details. |
| */ |
| |
| #include <linux/init.h> |
| #include <linux/kernel.h> |
| #include <linux/sched.h> |
| #include <linux/errno.h> |
| #include <linux/slab.h> |
| #include <linux/module.h> |
| #include <linux/spinlock.h> |
| #include <linux/list.h> |
| #include <linux/usb.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/ethtool.h> |
| #include <linux/wireless.h> |
| #include <linux/firmware.h> |
| #include <linux/moduleparam.h> |
| #include <net/mac80211.h> |
| #include "rtl8xxxu.h" |
| #include "rtl8xxxu_regs.h" |
| |
| #define DRIVER_NAME "rtl8xxxu" |
| |
| static int rtl8xxxu_debug = RTL8XXXU_DEBUG_EFUSE; |
| static bool rtl8xxxu_ht40_2g; |
| |
| MODULE_AUTHOR("Jes Sorensen <Jes.Sorensen@redhat.com>"); |
| MODULE_DESCRIPTION("RTL8XXXu USB mac80211 Wireless LAN Driver"); |
| MODULE_LICENSE("GPL"); |
| MODULE_FIRMWARE("rtlwifi/rtl8723aufw_A.bin"); |
| MODULE_FIRMWARE("rtlwifi/rtl8723aufw_B.bin"); |
| MODULE_FIRMWARE("rtlwifi/rtl8723aufw_B_NoBT.bin"); |
| MODULE_FIRMWARE("rtlwifi/rtl8192cufw_A.bin"); |
| MODULE_FIRMWARE("rtlwifi/rtl8192cufw_B.bin"); |
| MODULE_FIRMWARE("rtlwifi/rtl8192cufw_TMSC.bin"); |
| MODULE_FIRMWARE("rtlwifi/rtl8192eu_nic.bin"); |
| MODULE_FIRMWARE("rtlwifi/rtl8723bu_nic.bin"); |
| MODULE_FIRMWARE("rtlwifi/rtl8723bu_bt.bin"); |
| |
| module_param_named(debug, rtl8xxxu_debug, int, 0600); |
| MODULE_PARM_DESC(debug, "Set debug mask"); |
| module_param_named(ht40_2g, rtl8xxxu_ht40_2g, bool, 0600); |
| MODULE_PARM_DESC(ht40_2g, "Enable HT40 support on the 2.4GHz band"); |
| |
| #define USB_VENDOR_ID_REALTEK 0x0bda |
| /* Minimum IEEE80211_MAX_FRAME_LEN */ |
| #define RTL_RX_BUFFER_SIZE IEEE80211_MAX_FRAME_LEN |
| #define RTL8XXXU_RX_URBS 32 |
| #define RTL8XXXU_RX_URB_PENDING_WATER 8 |
| #define RTL8XXXU_TX_URBS 64 |
| #define RTL8XXXU_TX_URB_LOW_WATER 25 |
| #define RTL8XXXU_TX_URB_HIGH_WATER 32 |
| |
| static int rtl8xxxu_submit_rx_urb(struct rtl8xxxu_priv *priv, |
| struct rtl8xxxu_rx_urb *rx_urb); |
| |
| static struct ieee80211_rate rtl8xxxu_rates[] = { |
| { .bitrate = 10, .hw_value = DESC_RATE_1M, .flags = 0 }, |
| { .bitrate = 20, .hw_value = DESC_RATE_2M, .flags = 0 }, |
| { .bitrate = 55, .hw_value = DESC_RATE_5_5M, .flags = 0 }, |
| { .bitrate = 110, .hw_value = DESC_RATE_11M, .flags = 0 }, |
| { .bitrate = 60, .hw_value = DESC_RATE_6M, .flags = 0 }, |
| { .bitrate = 90, .hw_value = DESC_RATE_9M, .flags = 0 }, |
| { .bitrate = 120, .hw_value = DESC_RATE_12M, .flags = 0 }, |
| { .bitrate = 180, .hw_value = DESC_RATE_18M, .flags = 0 }, |
| { .bitrate = 240, .hw_value = DESC_RATE_24M, .flags = 0 }, |
| { .bitrate = 360, .hw_value = DESC_RATE_36M, .flags = 0 }, |
| { .bitrate = 480, .hw_value = DESC_RATE_48M, .flags = 0 }, |
| { .bitrate = 540, .hw_value = DESC_RATE_54M, .flags = 0 }, |
| }; |
| |
| static struct ieee80211_channel rtl8xxxu_channels_2g[] = { |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2412, |
| .hw_value = 1, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2417, |
| .hw_value = 2, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2422, |
| .hw_value = 3, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2427, |
| .hw_value = 4, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2432, |
| .hw_value = 5, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2437, |
| .hw_value = 6, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2442, |
| .hw_value = 7, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2447, |
| .hw_value = 8, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2452, |
| .hw_value = 9, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2457, |
| .hw_value = 10, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2462, |
| .hw_value = 11, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2467, |
| .hw_value = 12, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2472, |
| .hw_value = 13, .max_power = 30 }, |
| { .band = IEEE80211_BAND_2GHZ, .center_freq = 2484, |
| .hw_value = 14, .max_power = 30 } |
| }; |
| |
| static struct ieee80211_supported_band rtl8xxxu_supported_band = { |
| .channels = rtl8xxxu_channels_2g, |
| .n_channels = ARRAY_SIZE(rtl8xxxu_channels_2g), |
| .bitrates = rtl8xxxu_rates, |
| .n_bitrates = ARRAY_SIZE(rtl8xxxu_rates), |
| }; |
| |
| static struct rtl8xxxu_reg8val rtl8723a_mac_init_table[] = { |
| {0x420, 0x80}, {0x423, 0x00}, {0x430, 0x00}, {0x431, 0x00}, |
| {0x432, 0x00}, {0x433, 0x01}, {0x434, 0x04}, {0x435, 0x05}, |
| {0x436, 0x06}, {0x437, 0x07}, {0x438, 0x00}, {0x439, 0x00}, |
| {0x43a, 0x00}, {0x43b, 0x01}, {0x43c, 0x04}, {0x43d, 0x05}, |
| {0x43e, 0x06}, {0x43f, 0x07}, {0x440, 0x5d}, {0x441, 0x01}, |
| {0x442, 0x00}, {0x444, 0x15}, {0x445, 0xf0}, {0x446, 0x0f}, |
| {0x447, 0x00}, {0x458, 0x41}, {0x459, 0xa8}, {0x45a, 0x72}, |
| {0x45b, 0xb9}, {0x460, 0x66}, {0x461, 0x66}, {0x462, 0x08}, |
| {0x463, 0x03}, {0x4c8, 0xff}, {0x4c9, 0x08}, {0x4cc, 0xff}, |
| {0x4cd, 0xff}, {0x4ce, 0x01}, {0x500, 0x26}, {0x501, 0xa2}, |
| {0x502, 0x2f}, {0x503, 0x00}, {0x504, 0x28}, {0x505, 0xa3}, |
| {0x506, 0x5e}, {0x507, 0x00}, {0x508, 0x2b}, {0x509, 0xa4}, |
| {0x50a, 0x5e}, {0x50b, 0x00}, {0x50c, 0x4f}, {0x50d, 0xa4}, |
| {0x50e, 0x00}, {0x50f, 0x00}, {0x512, 0x1c}, {0x514, 0x0a}, |
| {0x515, 0x10}, {0x516, 0x0a}, {0x517, 0x10}, {0x51a, 0x16}, |
| {0x524, 0x0f}, {0x525, 0x4f}, {0x546, 0x40}, {0x547, 0x00}, |
| {0x550, 0x10}, {0x551, 0x10}, {0x559, 0x02}, {0x55a, 0x02}, |
| {0x55d, 0xff}, {0x605, 0x30}, {0x608, 0x0e}, {0x609, 0x2a}, |
| {0x652, 0x20}, {0x63c, 0x0a}, {0x63d, 0x0a}, {0x63e, 0x0e}, |
| {0x63f, 0x0e}, {0x66e, 0x05}, {0x700, 0x21}, {0x701, 0x43}, |
| {0x702, 0x65}, {0x703, 0x87}, {0x708, 0x21}, {0x709, 0x43}, |
| {0x70a, 0x65}, {0x70b, 0x87}, {0xffff, 0xff}, |
| }; |
| |
| static struct rtl8xxxu_reg8val rtl8723b_mac_init_table[] = { |
| {0x02f, 0x30}, {0x035, 0x00}, {0x039, 0x08}, {0x04e, 0xe0}, |
| {0x064, 0x00}, {0x067, 0x20}, {0x428, 0x0a}, {0x429, 0x10}, |
| {0x430, 0x00}, {0x431, 0x00}, |
| {0x432, 0x00}, {0x433, 0x01}, {0x434, 0x04}, {0x435, 0x05}, |
| {0x436, 0x07}, {0x437, 0x08}, {0x43c, 0x04}, {0x43d, 0x05}, |
| {0x43e, 0x07}, {0x43f, 0x08}, {0x440, 0x5d}, {0x441, 0x01}, |
| {0x442, 0x00}, {0x444, 0x10}, {0x445, 0x00}, {0x446, 0x00}, |
| {0x447, 0x00}, {0x448, 0x00}, {0x449, 0xf0}, {0x44a, 0x0f}, |
| {0x44b, 0x3e}, {0x44c, 0x10}, {0x44d, 0x00}, {0x44e, 0x00}, |
| {0x44f, 0x00}, {0x450, 0x00}, {0x451, 0xf0}, {0x452, 0x0f}, |
| {0x453, 0x00}, {0x456, 0x5e}, {0x460, 0x66}, {0x461, 0x66}, |
| {0x4c8, 0xff}, {0x4c9, 0x08}, {0x4cc, 0xff}, |
| {0x4cd, 0xff}, {0x4ce, 0x01}, {0x500, 0x26}, {0x501, 0xa2}, |
| {0x502, 0x2f}, {0x503, 0x00}, {0x504, 0x28}, {0x505, 0xa3}, |
| {0x506, 0x5e}, {0x507, 0x00}, {0x508, 0x2b}, {0x509, 0xa4}, |
| {0x50a, 0x5e}, {0x50b, 0x00}, {0x50c, 0x4f}, {0x50d, 0xa4}, |
| {0x50e, 0x00}, {0x50f, 0x00}, {0x512, 0x1c}, {0x514, 0x0a}, |
| {0x516, 0x0a}, {0x525, 0x4f}, |
| {0x550, 0x10}, {0x551, 0x10}, {0x559, 0x02}, {0x55c, 0x50}, |
| {0x55d, 0xff}, {0x605, 0x30}, {0x608, 0x0e}, {0x609, 0x2a}, |
| {0x620, 0xff}, {0x621, 0xff}, {0x622, 0xff}, {0x623, 0xff}, |
| {0x624, 0xff}, {0x625, 0xff}, {0x626, 0xff}, {0x627, 0xff}, |
| {0x638, 0x50}, {0x63c, 0x0a}, {0x63d, 0x0a}, {0x63e, 0x0e}, |
| {0x63f, 0x0e}, {0x640, 0x40}, {0x642, 0x40}, {0x643, 0x00}, |
| {0x652, 0xc8}, {0x66e, 0x05}, {0x700, 0x21}, {0x701, 0x43}, |
| {0x702, 0x65}, {0x703, 0x87}, {0x708, 0x21}, {0x709, 0x43}, |
| {0x70a, 0x65}, {0x70b, 0x87}, {0x765, 0x18}, {0x76e, 0x04}, |
| {0xffff, 0xff}, |
| }; |
| |
| static struct rtl8xxxu_reg32val rtl8723a_phy_1t_init_table[] = { |
| {0x800, 0x80040000}, {0x804, 0x00000003}, |
| {0x808, 0x0000fc00}, {0x80c, 0x0000000a}, |
| {0x810, 0x10001331}, {0x814, 0x020c3d10}, |
| {0x818, 0x02200385}, {0x81c, 0x00000000}, |
| {0x820, 0x01000100}, {0x824, 0x00390004}, |
| {0x828, 0x00000000}, {0x82c, 0x00000000}, |
| {0x830, 0x00000000}, {0x834, 0x00000000}, |
| {0x838, 0x00000000}, {0x83c, 0x00000000}, |
| {0x840, 0x00010000}, {0x844, 0x00000000}, |
| {0x848, 0x00000000}, {0x84c, 0x00000000}, |
| {0x850, 0x00000000}, {0x854, 0x00000000}, |
| {0x858, 0x569a569a}, {0x85c, 0x001b25a4}, |
| {0x860, 0x66f60110}, {0x864, 0x061f0130}, |
| {0x868, 0x00000000}, {0x86c, 0x32323200}, |
| {0x870, 0x07000760}, {0x874, 0x22004000}, |
| {0x878, 0x00000808}, {0x87c, 0x00000000}, |
| {0x880, 0xc0083070}, {0x884, 0x000004d5}, |
| {0x888, 0x00000000}, {0x88c, 0xccc000c0}, |
| {0x890, 0x00000800}, {0x894, 0xfffffffe}, |
| {0x898, 0x40302010}, {0x89c, 0x00706050}, |
| {0x900, 0x00000000}, {0x904, 0x00000023}, |
| {0x908, 0x00000000}, {0x90c, 0x81121111}, |
| {0xa00, 0x00d047c8}, {0xa04, 0x80ff000c}, |
| {0xa08, 0x8c838300}, {0xa0c, 0x2e68120f}, |
| {0xa10, 0x9500bb78}, {0xa14, 0x11144028}, |
| {0xa18, 0x00881117}, {0xa1c, 0x89140f00}, |
| {0xa20, 0x1a1b0000}, {0xa24, 0x090e1317}, |
| {0xa28, 0x00000204}, {0xa2c, 0x00d30000}, |
| {0xa70, 0x101fbf00}, {0xa74, 0x00000007}, |
| {0xa78, 0x00000900}, |
| {0xc00, 0x48071d40}, {0xc04, 0x03a05611}, |
| {0xc08, 0x000000e4}, {0xc0c, 0x6c6c6c6c}, |
| {0xc10, 0x08800000}, {0xc14, 0x40000100}, |
| {0xc18, 0x08800000}, {0xc1c, 0x40000100}, |
| {0xc20, 0x00000000}, {0xc24, 0x00000000}, |
| {0xc28, 0x00000000}, {0xc2c, 0x00000000}, |
| {0xc30, 0x69e9ac44}, {0xc34, 0x469652af}, |
| {0xc38, 0x49795994}, {0xc3c, 0x0a97971c}, |
| {0xc40, 0x1f7c403f}, {0xc44, 0x000100b7}, |
| {0xc48, 0xec020107}, {0xc4c, 0x007f037f}, |
| {0xc50, 0x69543420}, {0xc54, 0x43bc0094}, |
| {0xc58, 0x69543420}, {0xc5c, 0x433c0094}, |
| {0xc60, 0x00000000}, {0xc64, 0x7112848b}, |
| {0xc68, 0x47c00bff}, {0xc6c, 0x00000036}, |
| {0xc70, 0x2c7f000d}, {0xc74, 0x018610db}, |
| {0xc78, 0x0000001f}, {0xc7c, 0x00b91612}, |
| {0xc80, 0x40000100}, {0xc84, 0x20f60000}, |
| {0xc88, 0x40000100}, {0xc8c, 0x20200000}, |
| {0xc90, 0x00121820}, {0xc94, 0x00000000}, |
| {0xc98, 0x00121820}, {0xc9c, 0x00007f7f}, |
| {0xca0, 0x00000000}, {0xca4, 0x00000080}, |
| {0xca8, 0x00000000}, {0xcac, 0x00000000}, |
| {0xcb0, 0x00000000}, {0xcb4, 0x00000000}, |
| {0xcb8, 0x00000000}, {0xcbc, 0x28000000}, |
| {0xcc0, 0x00000000}, {0xcc4, 0x00000000}, |
| {0xcc8, 0x00000000}, {0xccc, 0x00000000}, |
| {0xcd0, 0x00000000}, {0xcd4, 0x00000000}, |
| {0xcd8, 0x64b22427}, {0xcdc, 0x00766932}, |
| {0xce0, 0x00222222}, {0xce4, 0x00000000}, |
| {0xce8, 0x37644302}, {0xcec, 0x2f97d40c}, |
| {0xd00, 0x00080740}, {0xd04, 0x00020401}, |
| {0xd08, 0x0000907f}, {0xd0c, 0x20010201}, |
| {0xd10, 0xa0633333}, {0xd14, 0x3333bc43}, |
| {0xd18, 0x7a8f5b6b}, {0xd2c, 0xcc979975}, |
| {0xd30, 0x00000000}, {0xd34, 0x80608000}, |
| {0xd38, 0x00000000}, {0xd3c, 0x00027293}, |
| {0xd40, 0x00000000}, {0xd44, 0x00000000}, |
| {0xd48, 0x00000000}, {0xd4c, 0x00000000}, |
| {0xd50, 0x6437140a}, {0xd54, 0x00000000}, |
| {0xd58, 0x00000000}, {0xd5c, 0x30032064}, |
| {0xd60, 0x4653de68}, {0xd64, 0x04518a3c}, |
| {0xd68, 0x00002101}, {0xd6c, 0x2a201c16}, |
| {0xd70, 0x1812362e}, {0xd74, 0x322c2220}, |
| {0xd78, 0x000e3c24}, {0xe00, 0x2a2a2a2a}, |
| {0xe04, 0x2a2a2a2a}, {0xe08, 0x03902a2a}, |
| {0xe10, 0x2a2a2a2a}, {0xe14, 0x2a2a2a2a}, |
| {0xe18, 0x2a2a2a2a}, {0xe1c, 0x2a2a2a2a}, |
| {0xe28, 0x00000000}, {0xe30, 0x1000dc1f}, |
| {0xe34, 0x10008c1f}, {0xe38, 0x02140102}, |
| {0xe3c, 0x681604c2}, {0xe40, 0x01007c00}, |
| {0xe44, 0x01004800}, {0xe48, 0xfb000000}, |
| {0xe4c, 0x000028d1}, {0xe50, 0x1000dc1f}, |
| {0xe54, 0x10008c1f}, {0xe58, 0x02140102}, |
| {0xe5c, 0x28160d05}, {0xe60, 0x00000008}, |
| {0xe68, 0x001b25a4}, {0xe6c, 0x631b25a0}, |
| {0xe70, 0x631b25a0}, {0xe74, 0x081b25a0}, |
| {0xe78, 0x081b25a0}, {0xe7c, 0x081b25a0}, |
| {0xe80, 0x081b25a0}, {0xe84, 0x631b25a0}, |
| {0xe88, 0x081b25a0}, {0xe8c, 0x631b25a0}, |
| {0xed0, 0x631b25a0}, {0xed4, 0x631b25a0}, |
| {0xed8, 0x631b25a0}, {0xedc, 0x001b25a0}, |
| {0xee0, 0x001b25a0}, {0xeec, 0x6b1b25a0}, |
| {0xf14, 0x00000003}, {0xf4c, 0x00000000}, |
| {0xf00, 0x00000300}, |
| {0xffff, 0xffffffff}, |
| }; |
| |
| static struct rtl8xxxu_reg32val rtl8723b_phy_1t_init_table[] = { |
| {0x800, 0x80040000}, {0x804, 0x00000003}, |
| {0x808, 0x0000fc00}, {0x80c, 0x0000000a}, |
| {0x810, 0x10001331}, {0x814, 0x020c3d10}, |
| {0x818, 0x02200385}, {0x81c, 0x00000000}, |
| {0x820, 0x01000100}, {0x824, 0x00190204}, |
| {0x828, 0x00000000}, {0x82c, 0x00000000}, |
| {0x830, 0x00000000}, {0x834, 0x00000000}, |
| {0x838, 0x00000000}, {0x83c, 0x00000000}, |
| {0x840, 0x00010000}, {0x844, 0x00000000}, |
| {0x848, 0x00000000}, {0x84c, 0x00000000}, |
| {0x850, 0x00000000}, {0x854, 0x00000000}, |
| {0x858, 0x569a11a9}, {0x85c, 0x01000014}, |
| {0x860, 0x66f60110}, {0x864, 0x061f0649}, |
| {0x868, 0x00000000}, {0x86c, 0x27272700}, |
| {0x870, 0x07000760}, {0x874, 0x25004000}, |
| {0x878, 0x00000808}, {0x87c, 0x00000000}, |
| {0x880, 0xb0000c1c}, {0x884, 0x00000001}, |
| {0x888, 0x00000000}, {0x88c, 0xccc000c0}, |
| {0x890, 0x00000800}, {0x894, 0xfffffffe}, |
| {0x898, 0x40302010}, {0x89c, 0x00706050}, |
| {0x900, 0x00000000}, {0x904, 0x00000023}, |
| {0x908, 0x00000000}, {0x90c, 0x81121111}, |
| {0x910, 0x00000002}, {0x914, 0x00000201}, |
| {0xa00, 0x00d047c8}, {0xa04, 0x80ff800c}, |
| {0xa08, 0x8c838300}, {0xa0c, 0x2e7f120f}, |
| {0xa10, 0x9500bb78}, {0xa14, 0x1114d028}, |
| {0xa18, 0x00881117}, {0xa1c, 0x89140f00}, |
| {0xa20, 0x1a1b0000}, {0xa24, 0x090e1317}, |
| {0xa28, 0x00000204}, {0xa2c, 0x00d30000}, |
| {0xa70, 0x101fbf00}, {0xa74, 0x00000007}, |
| {0xa78, 0x00000900}, {0xa7c, 0x225b0606}, |
| {0xa80, 0x21806490}, {0xb2c, 0x00000000}, |
| {0xc00, 0x48071d40}, {0xc04, 0x03a05611}, |
| {0xc08, 0x000000e4}, {0xc0c, 0x6c6c6c6c}, |
| {0xc10, 0x08800000}, {0xc14, 0x40000100}, |
| {0xc18, 0x08800000}, {0xc1c, 0x40000100}, |
| {0xc20, 0x00000000}, {0xc24, 0x00000000}, |
| {0xc28, 0x00000000}, {0xc2c, 0x00000000}, |
| {0xc30, 0x69e9ac44}, {0xc34, 0x469652af}, |
| {0xc38, 0x49795994}, {0xc3c, 0x0a97971c}, |
| {0xc40, 0x1f7c403f}, {0xc44, 0x000100b7}, |
| {0xc48, 0xec020107}, {0xc4c, 0x007f037f}, |
| {0xc50, 0x69553420}, {0xc54, 0x43bc0094}, |
| {0xc58, 0x00013149}, {0xc5c, 0x00250492}, |
| {0xc60, 0x00000000}, {0xc64, 0x7112848b}, |
| {0xc68, 0x47c00bff}, {0xc6c, 0x00000036}, |
| {0xc70, 0x2c7f000d}, {0xc74, 0x020610db}, |
| {0xc78, 0x0000001f}, {0xc7c, 0x00b91612}, |
| {0xc80, 0x390000e4}, {0xc84, 0x20f60000}, |
| {0xc88, 0x40000100}, {0xc8c, 0x20200000}, |
| {0xc90, 0x00020e1a}, {0xc94, 0x00000000}, |
| {0xc98, 0x00020e1a}, {0xc9c, 0x00007f7f}, |
| {0xca0, 0x00000000}, {0xca4, 0x000300a0}, |
| {0xca8, 0x00000000}, {0xcac, 0x00000000}, |
| {0xcb0, 0x00000000}, {0xcb4, 0x00000000}, |
| {0xcb8, 0x00000000}, {0xcbc, 0x28000000}, |
| {0xcc0, 0x00000000}, {0xcc4, 0x00000000}, |
| {0xcc8, 0x00000000}, {0xccc, 0x00000000}, |
| {0xcd0, 0x00000000}, {0xcd4, 0x00000000}, |
| {0xcd8, 0x64b22427}, {0xcdc, 0x00766932}, |
| {0xce0, 0x00222222}, {0xce4, 0x00000000}, |
| {0xce8, 0x37644302}, {0xcec, 0x2f97d40c}, |
| {0xd00, 0x00000740}, {0xd04, 0x40020401}, |
| {0xd08, 0x0000907f}, {0xd0c, 0x20010201}, |
| {0xd10, 0xa0633333}, {0xd14, 0x3333bc53}, |
| {0xd18, 0x7a8f5b6f}, {0xd2c, 0xcc979975}, |
| {0xd30, 0x00000000}, {0xd34, 0x80608000}, |
| {0xd38, 0x00000000}, {0xd3c, 0x00127353}, |
| {0xd40, 0x00000000}, {0xd44, 0x00000000}, |
| {0xd48, 0x00000000}, {0xd4c, 0x00000000}, |
| {0xd50, 0x6437140a}, {0xd54, 0x00000000}, |
| {0xd58, 0x00000282}, {0xd5c, 0x30032064}, |
| {0xd60, 0x4653de68}, {0xd64, 0x04518a3c}, |
| {0xd68, 0x00002101}, {0xd6c, 0x2a201c16}, |
| {0xd70, 0x1812362e}, {0xd74, 0x322c2220}, |
| {0xd78, 0x000e3c24}, {0xe00, 0x2d2d2d2d}, |
| {0xe04, 0x2d2d2d2d}, {0xe08, 0x0390272d}, |
| {0xe10, 0x2d2d2d2d}, {0xe14, 0x2d2d2d2d}, |
| {0xe18, 0x2d2d2d2d}, {0xe1c, 0x2d2d2d2d}, |
| {0xe28, 0x00000000}, {0xe30, 0x1000dc1f}, |
| {0xe34, 0x10008c1f}, {0xe38, 0x02140102}, |
| {0xe3c, 0x681604c2}, {0xe40, 0x01007c00}, |
| {0xe44, 0x01004800}, {0xe48, 0xfb000000}, |
| {0xe4c, 0x000028d1}, {0xe50, 0x1000dc1f}, |
| {0xe54, 0x10008c1f}, {0xe58, 0x02140102}, |
| {0xe5c, 0x28160d05}, {0xe60, 0x00000008}, |
| {0xe68, 0x001b2556}, {0xe6c, 0x00c00096}, |
| {0xe70, 0x00c00096}, {0xe74, 0x01000056}, |
| {0xe78, 0x01000014}, {0xe7c, 0x01000056}, |
| {0xe80, 0x01000014}, {0xe84, 0x00c00096}, |
| {0xe88, 0x01000056}, {0xe8c, 0x00c00096}, |
| {0xed0, 0x00c00096}, {0xed4, 0x00c00096}, |
| {0xed8, 0x00c00096}, {0xedc, 0x000000d6}, |
| {0xee0, 0x000000d6}, {0xeec, 0x01c00016}, |
| {0xf14, 0x00000003}, {0xf4c, 0x00000000}, |
| {0xf00, 0x00000300}, |
| {0x820, 0x01000100}, {0x800, 0x83040000}, |
| {0xffff, 0xffffffff}, |
| }; |
| |
| static struct rtl8xxxu_reg32val rtl8192cu_phy_2t_init_table[] = { |
| {0x024, 0x0011800f}, {0x028, 0x00ffdb83}, |
| {0x800, 0x80040002}, {0x804, 0x00000003}, |
| {0x808, 0x0000fc00}, {0x80c, 0x0000000a}, |
| {0x810, 0x10000330}, {0x814, 0x020c3d10}, |
| {0x818, 0x02200385}, {0x81c, 0x00000000}, |
| {0x820, 0x01000100}, {0x824, 0x00390004}, |
| {0x828, 0x01000100}, {0x82c, 0x00390004}, |
| {0x830, 0x27272727}, {0x834, 0x27272727}, |
| {0x838, 0x27272727}, {0x83c, 0x27272727}, |
| {0x840, 0x00010000}, {0x844, 0x00010000}, |
| {0x848, 0x27272727}, {0x84c, 0x27272727}, |
| {0x850, 0x00000000}, {0x854, 0x00000000}, |
| {0x858, 0x569a569a}, {0x85c, 0x0c1b25a4}, |
| {0x860, 0x66e60230}, {0x864, 0x061f0130}, |
| {0x868, 0x27272727}, {0x86c, 0x2b2b2b27}, |
| {0x870, 0x07000700}, {0x874, 0x22184000}, |
| {0x878, 0x08080808}, {0x87c, 0x00000000}, |
| {0x880, 0xc0083070}, {0x884, 0x000004d5}, |
| {0x888, 0x00000000}, {0x88c, 0xcc0000c0}, |
| {0x890, 0x00000800}, {0x894, 0xfffffffe}, |
| {0x898, 0x40302010}, {0x89c, 0x00706050}, |
| {0x900, 0x00000000}, {0x904, 0x00000023}, |
| {0x908, 0x00000000}, {0x90c, 0x81121313}, |
| {0xa00, 0x00d047c8}, {0xa04, 0x80ff000c}, |
| {0xa08, 0x8c838300}, {0xa0c, 0x2e68120f}, |
| {0xa10, 0x9500bb78}, {0xa14, 0x11144028}, |
| {0xa18, 0x00881117}, {0xa1c, 0x89140f00}, |
| {0xa20, 0x1a1b0000}, {0xa24, 0x090e1317}, |
| {0xa28, 0x00000204}, {0xa2c, 0x00d30000}, |
| {0xa70, 0x101fbf00}, {0xa74, 0x00000007}, |
| {0xc00, 0x48071d40}, {0xc04, 0x03a05633}, |
| {0xc08, 0x000000e4}, {0xc0c, 0x6c6c6c6c}, |
| {0xc10, 0x08800000}, {0xc14, 0x40000100}, |
| {0xc18, 0x08800000}, {0xc1c, 0x40000100}, |
| {0xc20, 0x00000000}, {0xc24, 0x00000000}, |
| {0xc28, 0x00000000}, {0xc2c, 0x00000000}, |
| {0xc30, 0x69e9ac44}, {0xc34, 0x469652cf}, |
| {0xc38, 0x49795994}, {0xc3c, 0x0a97971c}, |
| {0xc40, 0x1f7c403f}, {0xc44, 0x000100b7}, |
| {0xc48, 0xec020107}, {0xc4c, 0x007f037f}, |
| {0xc50, 0x69543420}, {0xc54, 0x43bc0094}, |
| {0xc58, 0x69543420}, {0xc5c, 0x433c0094}, |
| {0xc60, 0x00000000}, {0xc64, 0x5116848b}, |
| {0xc68, 0x47c00bff}, {0xc6c, 0x00000036}, |
| {0xc70, 0x2c7f000d}, {0xc74, 0x2186115b}, |
| {0xc78, 0x0000001f}, {0xc7c, 0x00b99612}, |
| {0xc80, 0x40000100}, {0xc84, 0x20f60000}, |
| {0xc88, 0x40000100}, {0xc8c, 0xa0e40000}, |
| {0xc90, 0x00121820}, {0xc94, 0x00000000}, |
| {0xc98, 0x00121820}, {0xc9c, 0x00007f7f}, |
| {0xca0, 0x00000000}, {0xca4, 0x00000080}, |
| {0xca8, 0x00000000}, {0xcac, 0x00000000}, |
| {0xcb0, 0x00000000}, {0xcb4, 0x00000000}, |
| {0xcb8, 0x00000000}, {0xcbc, 0x28000000}, |
| {0xcc0, 0x00000000}, {0xcc4, 0x00000000}, |
| {0xcc8, 0x00000000}, {0xccc, 0x00000000}, |
| {0xcd0, 0x00000000}, {0xcd4, 0x00000000}, |
| {0xcd8, 0x64b22427}, {0xcdc, 0x00766932}, |
| {0xce0, 0x00222222}, {0xce4, 0x00000000}, |
| {0xce8, 0x37644302}, {0xcec, 0x2f97d40c}, |
| {0xd00, 0x00080740}, {0xd04, 0x00020403}, |
| {0xd08, 0x0000907f}, {0xd0c, 0x20010201}, |
| {0xd10, 0xa0633333}, {0xd14, 0x3333bc43}, |
| {0xd18, 0x7a8f5b6b}, {0xd2c, 0xcc979975}, |
| {0xd30, 0x00000000}, {0xd34, 0x80608000}, |
| {0xd38, 0x00000000}, {0xd3c, 0x00027293}, |
| {0xd40, 0x00000000}, {0xd44, 0x00000000}, |
| {0xd48, 0x00000000}, {0xd4c, 0x00000000}, |
| {0xd50, 0x6437140a}, {0xd54, 0x00000000}, |
| {0xd58, 0x00000000}, {0xd5c, 0x30032064}, |
| {0xd60, 0x4653de68}, {0xd64, 0x04518a3c}, |
| {0xd68, 0x00002101}, {0xd6c, 0x2a201c16}, |
| {0xd70, 0x1812362e}, {0xd74, 0x322c2220}, |
| {0xd78, 0x000e3c24}, {0xe00, 0x2a2a2a2a}, |
| {0xe04, 0x2a2a2a2a}, {0xe08, 0x03902a2a}, |
| {0xe10, 0x2a2a2a2a}, {0xe14, 0x2a2a2a2a}, |
| {0xe18, 0x2a2a2a2a}, {0xe1c, 0x2a2a2a2a}, |
| {0xe28, 0x00000000}, {0xe30, 0x1000dc1f}, |
| {0xe34, 0x10008c1f}, {0xe38, 0x02140102}, |
| {0xe3c, 0x681604c2}, {0xe40, 0x01007c00}, |
| {0xe44, 0x01004800}, {0xe48, 0xfb000000}, |
| {0xe4c, 0x000028d1}, {0xe50, 0x1000dc1f}, |
| {0xe54, 0x10008c1f}, {0xe58, 0x02140102}, |
| {0xe5c, 0x28160d05}, {0xe60, 0x00000010}, |
| {0xe68, 0x001b25a4}, {0xe6c, 0x63db25a4}, |
| {0xe70, 0x63db25a4}, {0xe74, 0x0c1b25a4}, |
| {0xe78, 0x0c1b25a4}, {0xe7c, 0x0c1b25a4}, |
| {0xe80, 0x0c1b25a4}, {0xe84, 0x63db25a4}, |
| {0xe88, 0x0c1b25a4}, {0xe8c, 0x63db25a4}, |
| {0xed0, 0x63db25a4}, {0xed4, 0x63db25a4}, |
| {0xed8, 0x63db25a4}, {0xedc, 0x001b25a4}, |
| {0xee0, 0x001b25a4}, {0xeec, 0x6fdb25a4}, |
| {0xf14, 0x00000003}, {0xf4c, 0x00000000}, |
| {0xf00, 0x00000300}, |
| {0xffff, 0xffffffff}, |
| }; |
| |
| static struct rtl8xxxu_reg32val rtl8188ru_phy_1t_highpa_table[] = { |
| {0x024, 0x0011800f}, {0x028, 0x00ffdb83}, |
| {0x040, 0x000c0004}, {0x800, 0x80040000}, |
| {0x804, 0x00000001}, {0x808, 0x0000fc00}, |
| {0x80c, 0x0000000a}, {0x810, 0x10005388}, |
| {0x814, 0x020c3d10}, {0x818, 0x02200385}, |
| {0x81c, 0x00000000}, {0x820, 0x01000100}, |
| {0x824, 0x00390204}, {0x828, 0x00000000}, |
| {0x82c, 0x00000000}, {0x830, 0x00000000}, |
| {0x834, 0x00000000}, {0x838, 0x00000000}, |
| {0x83c, 0x00000000}, {0x840, 0x00010000}, |
| {0x844, 0x00000000}, {0x848, 0x00000000}, |
| {0x84c, 0x00000000}, {0x850, 0x00000000}, |
| {0x854, 0x00000000}, {0x858, 0x569a569a}, |
| {0x85c, 0x001b25a4}, {0x860, 0x66e60230}, |
| {0x864, 0x061f0130}, {0x868, 0x00000000}, |
| {0x86c, 0x20202000}, {0x870, 0x03000300}, |
| {0x874, 0x22004000}, {0x878, 0x00000808}, |
| {0x87c, 0x00ffc3f1}, {0x880, 0xc0083070}, |
| {0x884, 0x000004d5}, {0x888, 0x00000000}, |
| {0x88c, 0xccc000c0}, {0x890, 0x00000800}, |
| {0x894, 0xfffffffe}, {0x898, 0x40302010}, |
| {0x89c, 0x00706050}, {0x900, 0x00000000}, |
| {0x904, 0x00000023}, {0x908, 0x00000000}, |
| {0x90c, 0x81121111}, {0xa00, 0x00d047c8}, |
| {0xa04, 0x80ff000c}, {0xa08, 0x8c838300}, |
| {0xa0c, 0x2e68120f}, {0xa10, 0x9500bb78}, |
| {0xa14, 0x11144028}, {0xa18, 0x00881117}, |
| {0xa1c, 0x89140f00}, {0xa20, 0x15160000}, |
| {0xa24, 0x070b0f12}, {0xa28, 0x00000104}, |
| {0xa2c, 0x00d30000}, {0xa70, 0x101fbf00}, |
| {0xa74, 0x00000007}, {0xc00, 0x48071d40}, |
| {0xc04, 0x03a05611}, {0xc08, 0x000000e4}, |
| {0xc0c, 0x6c6c6c6c}, {0xc10, 0x08800000}, |
| {0xc14, 0x40000100}, {0xc18, 0x08800000}, |
| {0xc1c, 0x40000100}, {0xc20, 0x00000000}, |
| {0xc24, 0x00000000}, {0xc28, 0x00000000}, |
| {0xc2c, 0x00000000}, {0xc30, 0x69e9ac44}, |
| {0xc34, 0x469652cf}, {0xc38, 0x49795994}, |
| {0xc3c, 0x0a97971c}, {0xc40, 0x1f7c403f}, |
| {0xc44, 0x000100b7}, {0xc48, 0xec020107}, |
| {0xc4c, 0x007f037f}, {0xc50, 0x6954342e}, |
| {0xc54, 0x43bc0094}, {0xc58, 0x6954342f}, |
| {0xc5c, 0x433c0094}, {0xc60, 0x00000000}, |
| {0xc64, 0x5116848b}, {0xc68, 0x47c00bff}, |
| {0xc6c, 0x00000036}, {0xc70, 0x2c46000d}, |
| {0xc74, 0x018610db}, {0xc78, 0x0000001f}, |
| {0xc7c, 0x00b91612}, {0xc80, 0x24000090}, |
| {0xc84, 0x20f60000}, {0xc88, 0x24000090}, |
| {0xc8c, 0x20200000}, {0xc90, 0x00121820}, |
| {0xc94, 0x00000000}, {0xc98, 0x00121820}, |
| {0xc9c, 0x00007f7f}, {0xca0, 0x00000000}, |
| {0xca4, 0x00000080}, {0xca8, 0x00000000}, |
| {0xcac, 0x00000000}, {0xcb0, 0x00000000}, |
| {0xcb4, 0x00000000}, {0xcb8, 0x00000000}, |
| {0xcbc, 0x28000000}, {0xcc0, 0x00000000}, |
| {0xcc4, 0x00000000}, {0xcc8, 0x00000000}, |
| {0xccc, 0x00000000}, {0xcd0, 0x00000000}, |
| {0xcd4, 0x00000000}, {0xcd8, 0x64b22427}, |
| {0xcdc, 0x00766932}, {0xce0, 0x00222222}, |
| {0xce4, 0x00000000}, {0xce8, 0x37644302}, |
| {0xcec, 0x2f97d40c}, {0xd00, 0x00080740}, |
| {0xd04, 0x00020401}, {0xd08, 0x0000907f}, |
| {0xd0c, 0x20010201}, {0xd10, 0xa0633333}, |
| {0xd14, 0x3333bc43}, {0xd18, 0x7a8f5b6b}, |
| {0xd2c, 0xcc979975}, {0xd30, 0x00000000}, |
| {0xd34, 0x80608000}, {0xd38, 0x00000000}, |
| {0xd3c, 0x00027293}, {0xd40, 0x00000000}, |
| {0xd44, 0x00000000}, {0xd48, 0x00000000}, |
| {0xd4c, 0x00000000}, {0xd50, 0x6437140a}, |
| {0xd54, 0x00000000}, {0xd58, 0x00000000}, |
| {0xd5c, 0x30032064}, {0xd60, 0x4653de68}, |
| {0xd64, 0x04518a3c}, {0xd68, 0x00002101}, |
| {0xd6c, 0x2a201c16}, {0xd70, 0x1812362e}, |
| {0xd74, 0x322c2220}, {0xd78, 0x000e3c24}, |
| {0xe00, 0x24242424}, {0xe04, 0x24242424}, |
| {0xe08, 0x03902024}, {0xe10, 0x24242424}, |
| {0xe14, 0x24242424}, {0xe18, 0x24242424}, |
| {0xe1c, 0x24242424}, {0xe28, 0x00000000}, |
| {0xe30, 0x1000dc1f}, {0xe34, 0x10008c1f}, |
| {0xe38, 0x02140102}, {0xe3c, 0x681604c2}, |
| {0xe40, 0x01007c00}, {0xe44, 0x01004800}, |
| {0xe48, 0xfb000000}, {0xe4c, 0x000028d1}, |
| {0xe50, 0x1000dc1f}, {0xe54, 0x10008c1f}, |
| {0xe58, 0x02140102}, {0xe5c, 0x28160d05}, |
| {0xe60, 0x00000008}, {0xe68, 0x001b25a4}, |
| {0xe6c, 0x631b25a0}, {0xe70, 0x631b25a0}, |
| {0xe74, 0x081b25a0}, {0xe78, 0x081b25a0}, |
| {0xe7c, 0x081b25a0}, {0xe80, 0x081b25a0}, |
| {0xe84, 0x631b25a0}, {0xe88, 0x081b25a0}, |
| {0xe8c, 0x631b25a0}, {0xed0, 0x631b25a0}, |
| {0xed4, 0x631b25a0}, {0xed8, 0x631b25a0}, |
| {0xedc, 0x001b25a0}, {0xee0, 0x001b25a0}, |
| {0xeec, 0x6b1b25a0}, {0xee8, 0x31555448}, |
| {0xf14, 0x00000003}, {0xf4c, 0x00000000}, |
| {0xf00, 0x00000300}, |
| {0xffff, 0xffffffff}, |
| }; |
| |
| static struct rtl8xxxu_reg32val rtl8xxx_agc_standard_table[] = { |
| {0xc78, 0x7b000001}, {0xc78, 0x7b010001}, |
| {0xc78, 0x7b020001}, {0xc78, 0x7b030001}, |
| {0xc78, 0x7b040001}, {0xc78, 0x7b050001}, |
| {0xc78, 0x7a060001}, {0xc78, 0x79070001}, |
| {0xc78, 0x78080001}, {0xc78, 0x77090001}, |
| {0xc78, 0x760a0001}, {0xc78, 0x750b0001}, |
| {0xc78, 0x740c0001}, {0xc78, 0x730d0001}, |
| {0xc78, 0x720e0001}, {0xc78, 0x710f0001}, |
| {0xc78, 0x70100001}, {0xc78, 0x6f110001}, |
| {0xc78, 0x6e120001}, {0xc78, 0x6d130001}, |
| {0xc78, 0x6c140001}, {0xc78, 0x6b150001}, |
| {0xc78, 0x6a160001}, {0xc78, 0x69170001}, |
| {0xc78, 0x68180001}, {0xc78, 0x67190001}, |
| {0xc78, 0x661a0001}, {0xc78, 0x651b0001}, |
| {0xc78, 0x641c0001}, {0xc78, 0x631d0001}, |
| {0xc78, 0x621e0001}, {0xc78, 0x611f0001}, |
| {0xc78, 0x60200001}, {0xc78, 0x49210001}, |
| {0xc78, 0x48220001}, {0xc78, 0x47230001}, |
| {0xc78, 0x46240001}, {0xc78, 0x45250001}, |
| {0xc78, 0x44260001}, {0xc78, 0x43270001}, |
| {0xc78, 0x42280001}, {0xc78, 0x41290001}, |
| {0xc78, 0x402a0001}, {0xc78, 0x262b0001}, |
| {0xc78, 0x252c0001}, {0xc78, 0x242d0001}, |
| {0xc78, 0x232e0001}, {0xc78, 0x222f0001}, |
| {0xc78, 0x21300001}, {0xc78, 0x20310001}, |
| {0xc78, 0x06320001}, {0xc78, 0x05330001}, |
| {0xc78, 0x04340001}, {0xc78, 0x03350001}, |
| {0xc78, 0x02360001}, {0xc78, 0x01370001}, |
| {0xc78, 0x00380001}, {0xc78, 0x00390001}, |
| {0xc78, 0x003a0001}, {0xc78, 0x003b0001}, |
| {0xc78, 0x003c0001}, {0xc78, 0x003d0001}, |
| {0xc78, 0x003e0001}, {0xc78, 0x003f0001}, |
| {0xc78, 0x7b400001}, {0xc78, 0x7b410001}, |
| {0xc78, 0x7b420001}, {0xc78, 0x7b430001}, |
| {0xc78, 0x7b440001}, {0xc78, 0x7b450001}, |
| {0xc78, 0x7a460001}, {0xc78, 0x79470001}, |
| {0xc78, 0x78480001}, {0xc78, 0x77490001}, |
| {0xc78, 0x764a0001}, {0xc78, 0x754b0001}, |
| {0xc78, 0x744c0001}, {0xc78, 0x734d0001}, |
| {0xc78, 0x724e0001}, {0xc78, 0x714f0001}, |
| {0xc78, 0x70500001}, {0xc78, 0x6f510001}, |
| {0xc78, 0x6e520001}, {0xc78, 0x6d530001}, |
| {0xc78, 0x6c540001}, {0xc78, 0x6b550001}, |
| {0xc78, 0x6a560001}, {0xc78, 0x69570001}, |
| {0xc78, 0x68580001}, {0xc78, 0x67590001}, |
| {0xc78, 0x665a0001}, {0xc78, 0x655b0001}, |
| {0xc78, 0x645c0001}, {0xc78, 0x635d0001}, |
| {0xc78, 0x625e0001}, {0xc78, 0x615f0001}, |
| {0xc78, 0x60600001}, {0xc78, 0x49610001}, |
| {0xc78, 0x48620001}, {0xc78, 0x47630001}, |
| {0xc78, 0x46640001}, {0xc78, 0x45650001}, |
| {0xc78, 0x44660001}, {0xc78, 0x43670001}, |
| {0xc78, 0x42680001}, {0xc78, 0x41690001}, |
| {0xc78, 0x406a0001}, {0xc78, 0x266b0001}, |
| {0xc78, 0x256c0001}, {0xc78, 0x246d0001}, |
| {0xc78, 0x236e0001}, {0xc78, 0x226f0001}, |
| {0xc78, 0x21700001}, {0xc78, 0x20710001}, |
| {0xc78, 0x06720001}, {0xc78, 0x05730001}, |
| {0xc78, 0x04740001}, {0xc78, 0x03750001}, |
| {0xc78, 0x02760001}, {0xc78, 0x01770001}, |
| {0xc78, 0x00780001}, {0xc78, 0x00790001}, |
| {0xc78, 0x007a0001}, {0xc78, 0x007b0001}, |
| {0xc78, 0x007c0001}, {0xc78, 0x007d0001}, |
| {0xc78, 0x007e0001}, {0xc78, 0x007f0001}, |
| {0xc78, 0x3800001e}, {0xc78, 0x3801001e}, |
| {0xc78, 0x3802001e}, {0xc78, 0x3803001e}, |
| {0xc78, 0x3804001e}, {0xc78, 0x3805001e}, |
| {0xc78, 0x3806001e}, {0xc78, 0x3807001e}, |
| {0xc78, 0x3808001e}, {0xc78, 0x3c09001e}, |
| {0xc78, 0x3e0a001e}, {0xc78, 0x400b001e}, |
| {0xc78, 0x440c001e}, {0xc78, 0x480d001e}, |
| {0xc78, 0x4c0e001e}, {0xc78, 0x500f001e}, |
| {0xc78, 0x5210001e}, {0xc78, 0x5611001e}, |
| {0xc78, 0x5a12001e}, {0xc78, 0x5e13001e}, |
| {0xc78, 0x6014001e}, {0xc78, 0x6015001e}, |
| {0xc78, 0x6016001e}, {0xc78, 0x6217001e}, |
| {0xc78, 0x6218001e}, {0xc78, 0x6219001e}, |
| {0xc78, 0x621a001e}, {0xc78, 0x621b001e}, |
| {0xc78, 0x621c001e}, {0xc78, 0x621d001e}, |
| {0xc78, 0x621e001e}, {0xc78, 0x621f001e}, |
| {0xffff, 0xffffffff} |
| }; |
| |
| static struct rtl8xxxu_reg32val rtl8xxx_agc_highpa_table[] = { |
| {0xc78, 0x7b000001}, {0xc78, 0x7b010001}, |
| {0xc78, 0x7b020001}, {0xc78, 0x7b030001}, |
| {0xc78, 0x7b040001}, {0xc78, 0x7b050001}, |
| {0xc78, 0x7b060001}, {0xc78, 0x7b070001}, |
| {0xc78, 0x7b080001}, {0xc78, 0x7a090001}, |
| {0xc78, 0x790a0001}, {0xc78, 0x780b0001}, |
| {0xc78, 0x770c0001}, {0xc78, 0x760d0001}, |
| {0xc78, 0x750e0001}, {0xc78, 0x740f0001}, |
| {0xc78, 0x73100001}, {0xc78, 0x72110001}, |
| {0xc78, 0x71120001}, {0xc78, 0x70130001}, |
| {0xc78, 0x6f140001}, {0xc78, 0x6e150001}, |
| {0xc78, 0x6d160001}, {0xc78, 0x6c170001}, |
| {0xc78, 0x6b180001}, {0xc78, 0x6a190001}, |
| {0xc78, 0x691a0001}, {0xc78, 0x681b0001}, |
| {0xc78, 0x671c0001}, {0xc78, 0x661d0001}, |
| {0xc78, 0x651e0001}, {0xc78, 0x641f0001}, |
| {0xc78, 0x63200001}, {0xc78, 0x62210001}, |
| {0xc78, 0x61220001}, {0xc78, 0x60230001}, |
| {0xc78, 0x46240001}, {0xc78, 0x45250001}, |
| {0xc78, 0x44260001}, {0xc78, 0x43270001}, |
| {0xc78, 0x42280001}, {0xc78, 0x41290001}, |
| {0xc78, 0x402a0001}, {0xc78, 0x262b0001}, |
| {0xc78, 0x252c0001}, {0xc78, 0x242d0001}, |
| {0xc78, 0x232e0001}, {0xc78, 0x222f0001}, |
| {0xc78, 0x21300001}, {0xc78, 0x20310001}, |
| {0xc78, 0x06320001}, {0xc78, 0x05330001}, |
| {0xc78, 0x04340001}, {0xc78, 0x03350001}, |
| {0xc78, 0x02360001}, {0xc78, 0x01370001}, |
| {0xc78, 0x00380001}, {0xc78, 0x00390001}, |
| {0xc78, 0x003a0001}, {0xc78, 0x003b0001}, |
| {0xc78, 0x003c0001}, {0xc78, 0x003d0001}, |
| {0xc78, 0x003e0001}, {0xc78, 0x003f0001}, |
| {0xc78, 0x7b400001}, {0xc78, 0x7b410001}, |
| {0xc78, 0x7b420001}, {0xc78, 0x7b430001}, |
| {0xc78, 0x7b440001}, {0xc78, 0x7b450001}, |
| {0xc78, 0x7b460001}, {0xc78, 0x7b470001}, |
| {0xc78, 0x7b480001}, {0xc78, 0x7a490001}, |
| {0xc78, 0x794a0001}, {0xc78, 0x784b0001}, |
| {0xc78, 0x774c0001}, {0xc78, 0x764d0001}, |
| {0xc78, 0x754e0001}, {0xc78, 0x744f0001}, |
| {0xc78, 0x73500001}, {0xc78, 0x72510001}, |
| {0xc78, 0x71520001}, {0xc78, 0x70530001}, |
| {0xc78, 0x6f540001}, {0xc78, 0x6e550001}, |
| {0xc78, 0x6d560001}, {0xc78, 0x6c570001}, |
| {0xc78, 0x6b580001}, {0xc78, 0x6a590001}, |
| {0xc78, 0x695a0001}, {0xc78, 0x685b0001}, |
| {0xc78, 0x675c0001}, {0xc78, 0x665d0001}, |
| {0xc78, 0x655e0001}, {0xc78, 0x645f0001}, |
| {0xc78, 0x63600001}, {0xc78, 0x62610001}, |
| {0xc78, 0x61620001}, {0xc78, 0x60630001}, |
| {0xc78, 0x46640001}, {0xc78, 0x45650001}, |
| {0xc78, 0x44660001}, {0xc78, 0x43670001}, |
| {0xc78, 0x42680001}, {0xc78, 0x41690001}, |
| {0xc78, 0x406a0001}, {0xc78, 0x266b0001}, |
| {0xc78, 0x256c0001}, {0xc78, 0x246d0001}, |
| {0xc78, 0x236e0001}, {0xc78, 0x226f0001}, |
| {0xc78, 0x21700001}, {0xc78, 0x20710001}, |
| {0xc78, 0x06720001}, {0xc78, 0x05730001}, |
| {0xc78, 0x04740001}, {0xc78, 0x03750001}, |
| {0xc78, 0x02760001}, {0xc78, 0x01770001}, |
| {0xc78, 0x00780001}, {0xc78, 0x00790001}, |
| {0xc78, 0x007a0001}, {0xc78, 0x007b0001}, |
| {0xc78, 0x007c0001}, {0xc78, 0x007d0001}, |
| {0xc78, 0x007e0001}, {0xc78, 0x007f0001}, |
| {0xc78, 0x3800001e}, {0xc78, 0x3801001e}, |
| {0xc78, 0x3802001e}, {0xc78, 0x3803001e}, |
| {0xc78, 0x3804001e}, {0xc78, 0x3805001e}, |
| {0xc78, 0x3806001e}, {0xc78, 0x3807001e}, |
| {0xc78, 0x3808001e}, {0xc78, 0x3c09001e}, |
| {0xc78, 0x3e0a001e}, {0xc78, 0x400b001e}, |
| {0xc78, 0x440c001e}, {0xc78, 0x480d001e}, |
| {0xc78, 0x4c0e001e}, {0xc78, 0x500f001e}, |
| {0xc78, 0x5210001e}, {0xc78, 0x5611001e}, |
| {0xc78, 0x5a12001e}, {0xc78, 0x5e13001e}, |
| {0xc78, 0x6014001e}, {0xc78, 0x6015001e}, |
| {0xc78, 0x6016001e}, {0xc78, 0x6217001e}, |
| {0xc78, 0x6218001e}, {0xc78, 0x6219001e}, |
| {0xc78, 0x621a001e}, {0xc78, 0x621b001e}, |
| {0xc78, 0x621c001e}, {0xc78, 0x621d001e}, |
| {0xc78, 0x621e001e}, {0xc78, 0x621f001e}, |
| {0xffff, 0xffffffff} |
| }; |
| |
| static struct rtl8xxxu_reg32val rtl8xxx_agc_8723bu_table[] = { |
| {0xc78, 0xfd000001}, {0xc78, 0xfc010001}, |
| {0xc78, 0xfb020001}, {0xc78, 0xfa030001}, |
| {0xc78, 0xf9040001}, {0xc78, 0xf8050001}, |
| {0xc78, 0xf7060001}, {0xc78, 0xf6070001}, |
| {0xc78, 0xf5080001}, {0xc78, 0xf4090001}, |
| {0xc78, 0xf30a0001}, {0xc78, 0xf20b0001}, |
| {0xc78, 0xf10c0001}, {0xc78, 0xf00d0001}, |
| {0xc78, 0xef0e0001}, {0xc78, 0xee0f0001}, |
| {0xc78, 0xed100001}, {0xc78, 0xec110001}, |
| {0xc78, 0xeb120001}, {0xc78, 0xea130001}, |
| {0xc78, 0xe9140001}, {0xc78, 0xe8150001}, |
| {0xc78, 0xe7160001}, {0xc78, 0xe6170001}, |
| {0xc78, 0xe5180001}, {0xc78, 0xe4190001}, |
| {0xc78, 0xe31a0001}, {0xc78, 0xa51b0001}, |
| {0xc78, 0xa41c0001}, {0xc78, 0xa31d0001}, |
| {0xc78, 0x671e0001}, {0xc78, 0x661f0001}, |
| {0xc78, 0x65200001}, {0xc78, 0x64210001}, |
| {0xc78, 0x63220001}, {0xc78, 0x4a230001}, |
| {0xc78, 0x49240001}, {0xc78, 0x48250001}, |
| {0xc78, 0x47260001}, {0xc78, 0x46270001}, |
| {0xc78, 0x45280001}, {0xc78, 0x44290001}, |
| {0xc78, 0x432a0001}, {0xc78, 0x422b0001}, |
| {0xc78, 0x292c0001}, {0xc78, 0x282d0001}, |
| {0xc78, 0x272e0001}, {0xc78, 0x262f0001}, |
| {0xc78, 0x0a300001}, {0xc78, 0x09310001}, |
| {0xc78, 0x08320001}, {0xc78, 0x07330001}, |
| {0xc78, 0x06340001}, {0xc78, 0x05350001}, |
| {0xc78, 0x04360001}, {0xc78, 0x03370001}, |
| {0xc78, 0x02380001}, {0xc78, 0x01390001}, |
| {0xc78, 0x013a0001}, {0xc78, 0x013b0001}, |
| {0xc78, 0x013c0001}, {0xc78, 0x013d0001}, |
| {0xc78, 0x013e0001}, {0xc78, 0x013f0001}, |
| {0xc78, 0xfc400001}, {0xc78, 0xfb410001}, |
| {0xc78, 0xfa420001}, {0xc78, 0xf9430001}, |
| {0xc78, 0xf8440001}, {0xc78, 0xf7450001}, |
| {0xc78, 0xf6460001}, {0xc78, 0xf5470001}, |
| {0xc78, 0xf4480001}, {0xc78, 0xf3490001}, |
| {0xc78, 0xf24a0001}, {0xc78, 0xf14b0001}, |
| {0xc78, 0xf04c0001}, {0xc78, 0xef4d0001}, |
| {0xc78, 0xee4e0001}, {0xc78, 0xed4f0001}, |
| {0xc78, 0xec500001}, {0xc78, 0xeb510001}, |
| {0xc78, 0xea520001}, {0xc78, 0xe9530001}, |
| {0xc78, 0xe8540001}, {0xc78, 0xe7550001}, |
| {0xc78, 0xe6560001}, {0xc78, 0xe5570001}, |
| {0xc78, 0xe4580001}, {0xc78, 0xe3590001}, |
| {0xc78, 0xa65a0001}, {0xc78, 0xa55b0001}, |
| {0xc78, 0xa45c0001}, {0xc78, 0xa35d0001}, |
| {0xc78, 0x675e0001}, {0xc78, 0x665f0001}, |
| {0xc78, 0x65600001}, {0xc78, 0x64610001}, |
| {0xc78, 0x63620001}, {0xc78, 0x62630001}, |
| {0xc78, 0x61640001}, {0xc78, 0x48650001}, |
| {0xc78, 0x47660001}, {0xc78, 0x46670001}, |
| {0xc78, 0x45680001}, {0xc78, 0x44690001}, |
| {0xc78, 0x436a0001}, {0xc78, 0x426b0001}, |
| {0xc78, 0x286c0001}, {0xc78, 0x276d0001}, |
| {0xc78, 0x266e0001}, {0xc78, 0x256f0001}, |
| {0xc78, 0x24700001}, {0xc78, 0x09710001}, |
| {0xc78, 0x08720001}, {0xc78, 0x07730001}, |
| {0xc78, 0x06740001}, {0xc78, 0x05750001}, |
| {0xc78, 0x04760001}, {0xc78, 0x03770001}, |
| {0xc78, 0x02780001}, {0xc78, 0x01790001}, |
| {0xc78, 0x017a0001}, {0xc78, 0x017b0001}, |
| {0xc78, 0x017c0001}, {0xc78, 0x017d0001}, |
| {0xc78, 0x017e0001}, {0xc78, 0x017f0001}, |
| {0xc50, 0x69553422}, |
| {0xc50, 0x69553420}, |
| {0x824, 0x00390204}, |
| {0xffff, 0xffffffff} |
| }; |
| |
| static struct rtl8xxxu_rfregval rtl8723au_radioa_1t_init_table[] = { |
| {0x00, 0x00030159}, {0x01, 0x00031284}, |
| {0x02, 0x00098000}, {0x03, 0x00039c63}, |
| {0x04, 0x000210e7}, {0x09, 0x0002044f}, |
| {0x0a, 0x0001a3f1}, {0x0b, 0x00014787}, |
| {0x0c, 0x000896fe}, {0x0d, 0x0000e02c}, |
| {0x0e, 0x00039ce7}, {0x0f, 0x00000451}, |
| {0x19, 0x00000000}, {0x1a, 0x00030355}, |
| {0x1b, 0x00060a00}, {0x1c, 0x000fc378}, |
| {0x1d, 0x000a1250}, {0x1e, 0x0000024f}, |
| {0x1f, 0x00000000}, {0x20, 0x0000b614}, |
| {0x21, 0x0006c000}, {0x22, 0x00000000}, |
| {0x23, 0x00001558}, {0x24, 0x00000060}, |
| {0x25, 0x00000483}, {0x26, 0x0004f000}, |
| {0x27, 0x000ec7d9}, {0x28, 0x00057730}, |
| {0x29, 0x00004783}, {0x2a, 0x00000001}, |
| {0x2b, 0x00021334}, {0x2a, 0x00000000}, |
| {0x2b, 0x00000054}, {0x2a, 0x00000001}, |
| {0x2b, 0x00000808}, {0x2b, 0x00053333}, |
| {0x2c, 0x0000000c}, {0x2a, 0x00000002}, |
| {0x2b, 0x00000808}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000003}, |
| {0x2b, 0x00000808}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000004}, |
| {0x2b, 0x00000808}, {0x2b, 0x0006b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000005}, |
| {0x2b, 0x00000808}, {0x2b, 0x00073333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000006}, |
| {0x2b, 0x00000709}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000007}, |
| {0x2b, 0x00000709}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000008}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0004b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000009}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00053333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000a}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000b}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000c}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0006b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000d}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00073333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000e}, |
| {0x2b, 0x0000050b}, {0x2b, 0x00066666}, |
| {0x2c, 0x0000001a}, {0x2a, 0x000e0000}, |
| {0x10, 0x0004000f}, {0x11, 0x000e31fc}, |
| {0x10, 0x0006000f}, {0x11, 0x000ff9f8}, |
| {0x10, 0x0002000f}, {0x11, 0x000203f9}, |
| {0x10, 0x0003000f}, {0x11, 0x000ff500}, |
| {0x10, 0x00000000}, {0x11, 0x00000000}, |
| {0x10, 0x0008000f}, {0x11, 0x0003f100}, |
| {0x10, 0x0009000f}, {0x11, 0x00023100}, |
| {0x12, 0x00032000}, {0x12, 0x00071000}, |
| {0x12, 0x000b0000}, {0x12, 0x000fc000}, |
| {0x13, 0x000287b3}, {0x13, 0x000244b7}, |
| {0x13, 0x000204ab}, {0x13, 0x0001c49f}, |
| {0x13, 0x00018493}, {0x13, 0x0001429b}, |
| {0x13, 0x00010299}, {0x13, 0x0000c29c}, |
| {0x13, 0x000081a0}, {0x13, 0x000040ac}, |
| {0x13, 0x00000020}, {0x14, 0x0001944c}, |
| {0x14, 0x00059444}, {0x14, 0x0009944c}, |
| {0x14, 0x000d9444}, {0x15, 0x0000f474}, |
| {0x15, 0x0004f477}, {0x15, 0x0008f455}, |
| {0x15, 0x000cf455}, {0x16, 0x00000339}, |
| {0x16, 0x00040339}, {0x16, 0x00080339}, |
| {0x16, 0x000c0366}, {0x00, 0x00010159}, |
| {0x18, 0x0000f401}, {0xfe, 0x00000000}, |
| {0xfe, 0x00000000}, {0x1f, 0x00000003}, |
| {0xfe, 0x00000000}, {0xfe, 0x00000000}, |
| {0x1e, 0x00000247}, {0x1f, 0x00000000}, |
| {0x00, 0x00030159}, |
| {0xff, 0xffffffff} |
| }; |
| |
| static struct rtl8xxxu_rfregval rtl8723bu_radioa_1t_init_table[] = { |
| {0x00, 0x00010000}, {0xb0, 0x000dffe0}, |
| {0xfe, 0x00000000}, {0xfe, 0x00000000}, |
| {0xfe, 0x00000000}, {0xb1, 0x00000018}, |
| {0xfe, 0x00000000}, {0xfe, 0x00000000}, |
| {0xfe, 0x00000000}, {0xb2, 0x00084c00}, |
| {0xb5, 0x0000d2cc}, {0xb6, 0x000925aa}, |
| {0xb7, 0x00000010}, {0xb8, 0x0000907f}, |
| {0x5c, 0x00000002}, {0x7c, 0x00000002}, |
| {0x7e, 0x00000005}, {0x8b, 0x0006fc00}, |
| {0xb0, 0x000ff9f0}, {0x1c, 0x000739d2}, |
| {0x1e, 0x00000000}, {0xdf, 0x00000780}, |
| {0x50, 0x00067435}, |
| /* |
| * The 8723bu vendor driver indicates that bit 8 should be set in |
| * 0x51 for package types TFBGA90, TFBGA80, and TFBGA79. However |
| * they never actually check the package type - and just default |
| * to not setting it. |
| */ |
| {0x51, 0x0006b04e}, |
| {0x52, 0x000007d2}, {0x53, 0x00000000}, |
| {0x54, 0x00050400}, {0x55, 0x0004026e}, |
| {0xdd, 0x0000004c}, {0x70, 0x00067435}, |
| /* |
| * 0x71 has same package type condition as for register 0x51 |
| */ |
| {0x71, 0x0006b04e}, |
| {0x72, 0x000007d2}, {0x73, 0x00000000}, |
| {0x74, 0x00050400}, {0x75, 0x0004026e}, |
| {0xef, 0x00000100}, {0x34, 0x0000add7}, |
| {0x35, 0x00005c00}, {0x34, 0x00009dd4}, |
| {0x35, 0x00005000}, {0x34, 0x00008dd1}, |
| {0x35, 0x00004400}, {0x34, 0x00007dce}, |
| {0x35, 0x00003800}, {0x34, 0x00006cd1}, |
| {0x35, 0x00004400}, {0x34, 0x00005cce}, |
| {0x35, 0x00003800}, {0x34, 0x000048ce}, |
| {0x35, 0x00004400}, {0x34, 0x000034ce}, |
| {0x35, 0x00003800}, {0x34, 0x00002451}, |
| {0x35, 0x00004400}, {0x34, 0x0000144e}, |
| {0x35, 0x00003800}, {0x34, 0x00000051}, |
| {0x35, 0x00004400}, {0xef, 0x00000000}, |
| {0xef, 0x00000100}, {0xed, 0x00000010}, |
| {0x44, 0x0000add7}, {0x44, 0x00009dd4}, |
| {0x44, 0x00008dd1}, {0x44, 0x00007dce}, |
| {0x44, 0x00006cc1}, {0x44, 0x00005cce}, |
| {0x44, 0x000044d1}, {0x44, 0x000034ce}, |
| {0x44, 0x00002451}, {0x44, 0x0000144e}, |
| {0x44, 0x00000051}, {0xef, 0x00000000}, |
| {0xed, 0x00000000}, {0x7f, 0x00020080}, |
| {0xef, 0x00002000}, {0x3b, 0x000380ef}, |
| {0x3b, 0x000302fe}, {0x3b, 0x00028ce6}, |
| {0x3b, 0x000200bc}, {0x3b, 0x000188a5}, |
| {0x3b, 0x00010fbc}, {0x3b, 0x00008f71}, |
| {0x3b, 0x00000900}, {0xef, 0x00000000}, |
| {0xed, 0x00000001}, {0x40, 0x000380ef}, |
| {0x40, 0x000302fe}, {0x40, 0x00028ce6}, |
| {0x40, 0x000200bc}, {0x40, 0x000188a5}, |
| {0x40, 0x00010fbc}, {0x40, 0x00008f71}, |
| {0x40, 0x00000900}, {0xed, 0x00000000}, |
| {0x82, 0x00080000}, {0x83, 0x00008000}, |
| {0x84, 0x00048d80}, {0x85, 0x00068000}, |
| {0xa2, 0x00080000}, {0xa3, 0x00008000}, |
| {0xa4, 0x00048d80}, {0xa5, 0x00068000}, |
| {0xed, 0x00000002}, {0xef, 0x00000002}, |
| {0x56, 0x00000032}, {0x76, 0x00000032}, |
| {0x01, 0x00000780}, |
| {0xff, 0xffffffff} |
| }; |
| |
| static struct rtl8xxxu_rfregval rtl8192cu_radioa_2t_init_table[] = { |
| {0x00, 0x00030159}, {0x01, 0x00031284}, |
| {0x02, 0x00098000}, {0x03, 0x00018c63}, |
| {0x04, 0x000210e7}, {0x09, 0x0002044f}, |
| {0x0a, 0x0001adb1}, {0x0b, 0x00054867}, |
| {0x0c, 0x0008992e}, {0x0d, 0x0000e52c}, |
| {0x0e, 0x00039ce7}, {0x0f, 0x00000451}, |
| {0x19, 0x00000000}, {0x1a, 0x00010255}, |
| {0x1b, 0x00060a00}, {0x1c, 0x000fc378}, |
| {0x1d, 0x000a1250}, {0x1e, 0x0004445f}, |
| {0x1f, 0x00080001}, {0x20, 0x0000b614}, |
| {0x21, 0x0006c000}, {0x22, 0x00000000}, |
| {0x23, 0x00001558}, {0x24, 0x00000060}, |
| {0x25, 0x00000483}, {0x26, 0x0004f000}, |
| {0x27, 0x000ec7d9}, {0x28, 0x000577c0}, |
| {0x29, 0x00004783}, {0x2a, 0x00000001}, |
| {0x2b, 0x00021334}, {0x2a, 0x00000000}, |
| {0x2b, 0x00000054}, {0x2a, 0x00000001}, |
| {0x2b, 0x00000808}, {0x2b, 0x00053333}, |
| {0x2c, 0x0000000c}, {0x2a, 0x00000002}, |
| {0x2b, 0x00000808}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000003}, |
| {0x2b, 0x00000808}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000004}, |
| {0x2b, 0x00000808}, {0x2b, 0x0006b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000005}, |
| {0x2b, 0x00000808}, {0x2b, 0x00073333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000006}, |
| {0x2b, 0x00000709}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000007}, |
| {0x2b, 0x00000709}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000008}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0004b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000009}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00053333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000a}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000b}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000c}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0006b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000d}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00073333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000e}, |
| {0x2b, 0x0000050b}, {0x2b, 0x00066666}, |
| {0x2c, 0x0000001a}, {0x2a, 0x000e0000}, |
| {0x10, 0x0004000f}, {0x11, 0x000e31fc}, |
| {0x10, 0x0006000f}, {0x11, 0x000ff9f8}, |
| {0x10, 0x0002000f}, {0x11, 0x000203f9}, |
| {0x10, 0x0003000f}, {0x11, 0x000ff500}, |
| {0x10, 0x00000000}, {0x11, 0x00000000}, |
| {0x10, 0x0008000f}, {0x11, 0x0003f100}, |
| {0x10, 0x0009000f}, {0x11, 0x00023100}, |
| {0x12, 0x00032000}, {0x12, 0x00071000}, |
| {0x12, 0x000b0000}, {0x12, 0x000fc000}, |
| {0x13, 0x000287b3}, {0x13, 0x000244b7}, |
| {0x13, 0x000204ab}, {0x13, 0x0001c49f}, |
| {0x13, 0x00018493}, {0x13, 0x0001429b}, |
| {0x13, 0x00010299}, {0x13, 0x0000c29c}, |
| {0x13, 0x000081a0}, {0x13, 0x000040ac}, |
| {0x13, 0x00000020}, {0x14, 0x0001944c}, |
| {0x14, 0x00059444}, {0x14, 0x0009944c}, |
| {0x14, 0x000d9444}, {0x15, 0x0000f424}, |
| {0x15, 0x0004f424}, {0x15, 0x0008f424}, |
| {0x15, 0x000cf424}, {0x16, 0x000e0330}, |
| {0x16, 0x000a0330}, {0x16, 0x00060330}, |
| {0x16, 0x00020330}, {0x00, 0x00010159}, |
| {0x18, 0x0000f401}, {0xfe, 0x00000000}, |
| {0xfe, 0x00000000}, {0x1f, 0x00080003}, |
| {0xfe, 0x00000000}, {0xfe, 0x00000000}, |
| {0x1e, 0x00044457}, {0x1f, 0x00080000}, |
| {0x00, 0x00030159}, |
| {0xff, 0xffffffff} |
| }; |
| |
| static struct rtl8xxxu_rfregval rtl8192cu_radiob_2t_init_table[] = { |
| {0x00, 0x00030159}, {0x01, 0x00031284}, |
| {0x02, 0x00098000}, {0x03, 0x00018c63}, |
| {0x04, 0x000210e7}, {0x09, 0x0002044f}, |
| {0x0a, 0x0001adb1}, {0x0b, 0x00054867}, |
| {0x0c, 0x0008992e}, {0x0d, 0x0000e52c}, |
| {0x0e, 0x00039ce7}, {0x0f, 0x00000451}, |
| {0x12, 0x00032000}, {0x12, 0x00071000}, |
| {0x12, 0x000b0000}, {0x12, 0x000fc000}, |
| {0x13, 0x000287af}, {0x13, 0x000244b7}, |
| {0x13, 0x000204ab}, {0x13, 0x0001c49f}, |
| {0x13, 0x00018493}, {0x13, 0x00014297}, |
| {0x13, 0x00010295}, {0x13, 0x0000c298}, |
| {0x13, 0x0000819c}, {0x13, 0x000040a8}, |
| {0x13, 0x0000001c}, {0x14, 0x0001944c}, |
| {0x14, 0x00059444}, {0x14, 0x0009944c}, |
| {0x14, 0x000d9444}, {0x15, 0x0000f424}, |
| {0x15, 0x0004f424}, {0x15, 0x0008f424}, |
| {0x15, 0x000cf424}, {0x16, 0x000e0330}, |
| {0x16, 0x000a0330}, {0x16, 0x00060330}, |
| {0x16, 0x00020330}, |
| {0xff, 0xffffffff} |
| }; |
| |
| static struct rtl8xxxu_rfregval rtl8192cu_radioa_1t_init_table[] = { |
| {0x00, 0x00030159}, {0x01, 0x00031284}, |
| {0x02, 0x00098000}, {0x03, 0x00018c63}, |
| {0x04, 0x000210e7}, {0x09, 0x0002044f}, |
| {0x0a, 0x0001adb1}, {0x0b, 0x00054867}, |
| {0x0c, 0x0008992e}, {0x0d, 0x0000e52c}, |
| {0x0e, 0x00039ce7}, {0x0f, 0x00000451}, |
| {0x19, 0x00000000}, {0x1a, 0x00010255}, |
| {0x1b, 0x00060a00}, {0x1c, 0x000fc378}, |
| {0x1d, 0x000a1250}, {0x1e, 0x0004445f}, |
| {0x1f, 0x00080001}, {0x20, 0x0000b614}, |
| {0x21, 0x0006c000}, {0x22, 0x00000000}, |
| {0x23, 0x00001558}, {0x24, 0x00000060}, |
| {0x25, 0x00000483}, {0x26, 0x0004f000}, |
| {0x27, 0x000ec7d9}, {0x28, 0x000577c0}, |
| {0x29, 0x00004783}, {0x2a, 0x00000001}, |
| {0x2b, 0x00021334}, {0x2a, 0x00000000}, |
| {0x2b, 0x00000054}, {0x2a, 0x00000001}, |
| {0x2b, 0x00000808}, {0x2b, 0x00053333}, |
| {0x2c, 0x0000000c}, {0x2a, 0x00000002}, |
| {0x2b, 0x00000808}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000003}, |
| {0x2b, 0x00000808}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000004}, |
| {0x2b, 0x00000808}, {0x2b, 0x0006b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000005}, |
| {0x2b, 0x00000808}, {0x2b, 0x00073333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000006}, |
| {0x2b, 0x00000709}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000007}, |
| {0x2b, 0x00000709}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000008}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0004b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000009}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00053333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000a}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000b}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000c}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0006b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000d}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00073333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000e}, |
| {0x2b, 0x0000050b}, {0x2b, 0x00066666}, |
| {0x2c, 0x0000001a}, {0x2a, 0x000e0000}, |
| {0x10, 0x0004000f}, {0x11, 0x000e31fc}, |
| {0x10, 0x0006000f}, {0x11, 0x000ff9f8}, |
| {0x10, 0x0002000f}, {0x11, 0x000203f9}, |
| {0x10, 0x0003000f}, {0x11, 0x000ff500}, |
| {0x10, 0x00000000}, {0x11, 0x00000000}, |
| {0x10, 0x0008000f}, {0x11, 0x0003f100}, |
| {0x10, 0x0009000f}, {0x11, 0x00023100}, |
| {0x12, 0x00032000}, {0x12, 0x00071000}, |
| {0x12, 0x000b0000}, {0x12, 0x000fc000}, |
| {0x13, 0x000287b3}, {0x13, 0x000244b7}, |
| {0x13, 0x000204ab}, {0x13, 0x0001c49f}, |
| {0x13, 0x00018493}, {0x13, 0x0001429b}, |
| {0x13, 0x00010299}, {0x13, 0x0000c29c}, |
| {0x13, 0x000081a0}, {0x13, 0x000040ac}, |
| {0x13, 0x00000020}, {0x14, 0x0001944c}, |
| {0x14, 0x00059444}, {0x14, 0x0009944c}, |
| {0x14, 0x000d9444}, {0x15, 0x0000f405}, |
| {0x15, 0x0004f405}, {0x15, 0x0008f405}, |
| {0x15, 0x000cf405}, {0x16, 0x000e0330}, |
| {0x16, 0x000a0330}, {0x16, 0x00060330}, |
| {0x16, 0x00020330}, {0x00, 0x00010159}, |
| {0x18, 0x0000f401}, {0xfe, 0x00000000}, |
| {0xfe, 0x00000000}, {0x1f, 0x00080003}, |
| {0xfe, 0x00000000}, {0xfe, 0x00000000}, |
| {0x1e, 0x00044457}, {0x1f, 0x00080000}, |
| {0x00, 0x00030159}, |
| {0xff, 0xffffffff} |
| }; |
| |
| static struct rtl8xxxu_rfregval rtl8188ru_radioa_1t_highpa_table[] = { |
| {0x00, 0x00030159}, {0x01, 0x00031284}, |
| {0x02, 0x00098000}, {0x03, 0x00018c63}, |
| {0x04, 0x000210e7}, {0x09, 0x0002044f}, |
| {0x0a, 0x0001adb0}, {0x0b, 0x00054867}, |
| {0x0c, 0x0008992e}, {0x0d, 0x0000e529}, |
| {0x0e, 0x00039ce7}, {0x0f, 0x00000451}, |
| {0x19, 0x00000000}, {0x1a, 0x00000255}, |
| {0x1b, 0x00060a00}, {0x1c, 0x000fc378}, |
| {0x1d, 0x000a1250}, {0x1e, 0x0004445f}, |
| {0x1f, 0x00080001}, {0x20, 0x0000b614}, |
| {0x21, 0x0006c000}, {0x22, 0x0000083c}, |
| {0x23, 0x00001558}, {0x24, 0x00000060}, |
| {0x25, 0x00000483}, {0x26, 0x0004f000}, |
| {0x27, 0x000ec7d9}, {0x28, 0x000977c0}, |
| {0x29, 0x00004783}, {0x2a, 0x00000001}, |
| {0x2b, 0x00021334}, {0x2a, 0x00000000}, |
| {0x2b, 0x00000054}, {0x2a, 0x00000001}, |
| {0x2b, 0x00000808}, {0x2b, 0x00053333}, |
| {0x2c, 0x0000000c}, {0x2a, 0x00000002}, |
| {0x2b, 0x00000808}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000003}, |
| {0x2b, 0x00000808}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000004}, |
| {0x2b, 0x00000808}, {0x2b, 0x0006b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000005}, |
| {0x2b, 0x00000808}, {0x2b, 0x00073333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000006}, |
| {0x2b, 0x00000709}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000007}, |
| {0x2b, 0x00000709}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000008}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0004b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x00000009}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00053333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000a}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0005b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000b}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00063333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000c}, |
| {0x2b, 0x0000060a}, {0x2b, 0x0006b333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000d}, |
| {0x2b, 0x0000060a}, {0x2b, 0x00073333}, |
| {0x2c, 0x0000000d}, {0x2a, 0x0000000e}, |
| {0x2b, 0x0000050b}, {0x2b, 0x00066666}, |
| {0x2c, 0x0000001a}, {0x2a, 0x000e0000}, |
| {0x10, 0x0004000f}, {0x11, 0x000e31fc}, |
| {0x10, 0x0006000f}, {0x11, 0x000ff9f8}, |
| {0x10, 0x0002000f}, {0x11, 0x000203f9}, |
| {0x10, 0x0003000f}, {0x11, 0x000ff500}, |
| {0x10, 0x00000000}, {0x11, 0x00000000}, |
| {0x10, 0x0008000f}, {0x11, 0x0003f100}, |
| {0x10, 0x0009000f}, {0x11, 0x00023100}, |
| {0x12, 0x000d8000}, {0x12, 0x00090000}, |
| {0x12, 0x00051000}, {0x12, 0x00012000}, |
| {0x13, 0x00028fb4}, {0x13, 0x00024fa8}, |
| {0x13, 0x000207a4}, {0x13, 0x0001c3b0}, |
| {0x13, 0x000183a4}, {0x13, 0x00014398}, |
| {0x13, 0x000101a4}, {0x13, 0x0000c198}, |
| {0x13, 0x000080a4}, {0x13, 0x00004098}, |
| {0x13, 0x00000000}, {0x14, 0x0001944c}, |
| {0x14, 0x00059444}, {0x14, 0x0009944c}, |
| {0x14, 0x000d9444}, {0x15, 0x0000f405}, |
| {0x15, 0x0004f405}, {0x15, 0x0008f405}, |
| {0x15, 0x000cf405}, {0x16, 0x000e0330}, |
| {0x16, 0x000a0330}, {0x16, 0x00060330}, |
| {0x16, 0x00020330}, {0x00, 0x00010159}, |
| {0x18, 0x0000f401}, {0xfe, 0x00000000}, |
| {0xfe, 0x00000000}, {0x1f, 0x00080003}, |
| {0xfe, 0x00000000}, {0xfe, 0x00000000}, |
| {0x1e, 0x00044457}, {0x1f, 0x00080000}, |
| {0x00, 0x00030159}, |
| {0xff, 0xffffffff} |
| }; |
| |
| static struct rtl8xxxu_rfregs rtl8xxxu_rfregs[] = { |
| { /* RF_A */ |
| .hssiparm1 = REG_FPGA0_XA_HSSI_PARM1, |
| .hssiparm2 = REG_FPGA0_XA_HSSI_PARM2, |
| .lssiparm = REG_FPGA0_XA_LSSI_PARM, |
| .hspiread = REG_HSPI_XA_READBACK, |
| .lssiread = REG_FPGA0_XA_LSSI_READBACK, |
| .rf_sw_ctrl = REG_FPGA0_XA_RF_SW_CTRL, |
| }, |
| { /* RF_B */ |
| .hssiparm1 = REG_FPGA0_XB_HSSI_PARM1, |
| .hssiparm2 = REG_FPGA0_XB_HSSI_PARM2, |
| .lssiparm = REG_FPGA0_XB_LSSI_PARM, |
| .hspiread = REG_HSPI_XB_READBACK, |
| .lssiread = REG_FPGA0_XB_LSSI_READBACK, |
| .rf_sw_ctrl = REG_FPGA0_XB_RF_SW_CTRL, |
| }, |
| }; |
| |
| static const u32 rtl8723au_iqk_phy_iq_bb_reg[RTL8XXXU_BB_REGS] = { |
| REG_OFDM0_XA_RX_IQ_IMBALANCE, |
| REG_OFDM0_XB_RX_IQ_IMBALANCE, |
| REG_OFDM0_ENERGY_CCA_THRES, |
| REG_OFDM0_AGCR_SSI_TABLE, |
| REG_OFDM0_XA_TX_IQ_IMBALANCE, |
| REG_OFDM0_XB_TX_IQ_IMBALANCE, |
| REG_OFDM0_XC_TX_AFE, |
| REG_OFDM0_XD_TX_AFE, |
| REG_OFDM0_RX_IQ_EXT_ANTA |
| }; |
| |
| static u8 rtl8xxxu_read8(struct rtl8xxxu_priv *priv, u16 addr) |
| { |
| struct usb_device *udev = priv->udev; |
| int len; |
| u8 data; |
| |
| mutex_lock(&priv->usb_buf_mutex); |
| len = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), |
| REALTEK_USB_CMD_REQ, REALTEK_USB_READ, |
| addr, 0, &priv->usb_buf.val8, sizeof(u8), |
| RTW_USB_CONTROL_MSG_TIMEOUT); |
| data = priv->usb_buf.val8; |
| mutex_unlock(&priv->usb_buf_mutex); |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_REG_READ) |
| dev_info(&udev->dev, "%s(%04x) = 0x%02x, len %i\n", |
| __func__, addr, data, len); |
| return data; |
| } |
| |
| static u16 rtl8xxxu_read16(struct rtl8xxxu_priv *priv, u16 addr) |
| { |
| struct usb_device *udev = priv->udev; |
| int len; |
| u16 data; |
| |
| mutex_lock(&priv->usb_buf_mutex); |
| len = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), |
| REALTEK_USB_CMD_REQ, REALTEK_USB_READ, |
| addr, 0, &priv->usb_buf.val16, sizeof(u16), |
| RTW_USB_CONTROL_MSG_TIMEOUT); |
| data = le16_to_cpu(priv->usb_buf.val16); |
| mutex_unlock(&priv->usb_buf_mutex); |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_REG_READ) |
| dev_info(&udev->dev, "%s(%04x) = 0x%04x, len %i\n", |
| __func__, addr, data, len); |
| return data; |
| } |
| |
| static u32 rtl8xxxu_read32(struct rtl8xxxu_priv *priv, u16 addr) |
| { |
| struct usb_device *udev = priv->udev; |
| int len; |
| u32 data; |
| |
| mutex_lock(&priv->usb_buf_mutex); |
| len = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), |
| REALTEK_USB_CMD_REQ, REALTEK_USB_READ, |
| addr, 0, &priv->usb_buf.val32, sizeof(u32), |
| RTW_USB_CONTROL_MSG_TIMEOUT); |
| data = le32_to_cpu(priv->usb_buf.val32); |
| mutex_unlock(&priv->usb_buf_mutex); |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_REG_READ) |
| dev_info(&udev->dev, "%s(%04x) = 0x%08x, len %i\n", |
| __func__, addr, data, len); |
| return data; |
| } |
| |
| static int rtl8xxxu_write8(struct rtl8xxxu_priv *priv, u16 addr, u8 val) |
| { |
| struct usb_device *udev = priv->udev; |
| int ret; |
| |
| mutex_lock(&priv->usb_buf_mutex); |
| priv->usb_buf.val8 = val; |
| ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), |
| REALTEK_USB_CMD_REQ, REALTEK_USB_WRITE, |
| addr, 0, &priv->usb_buf.val8, sizeof(u8), |
| RTW_USB_CONTROL_MSG_TIMEOUT); |
| |
| mutex_unlock(&priv->usb_buf_mutex); |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_REG_WRITE) |
| dev_info(&udev->dev, "%s(%04x) = 0x%02x\n", |
| __func__, addr, val); |
| return ret; |
| } |
| |
| static int rtl8xxxu_write16(struct rtl8xxxu_priv *priv, u16 addr, u16 val) |
| { |
| struct usb_device *udev = priv->udev; |
| int ret; |
| |
| mutex_lock(&priv->usb_buf_mutex); |
| priv->usb_buf.val16 = cpu_to_le16(val); |
| ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), |
| REALTEK_USB_CMD_REQ, REALTEK_USB_WRITE, |
| addr, 0, &priv->usb_buf.val16, sizeof(u16), |
| RTW_USB_CONTROL_MSG_TIMEOUT); |
| mutex_unlock(&priv->usb_buf_mutex); |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_REG_WRITE) |
| dev_info(&udev->dev, "%s(%04x) = 0x%04x\n", |
| __func__, addr, val); |
| return ret; |
| } |
| |
| static int rtl8xxxu_write32(struct rtl8xxxu_priv *priv, u16 addr, u32 val) |
| { |
| struct usb_device *udev = priv->udev; |
| int ret; |
| |
| mutex_lock(&priv->usb_buf_mutex); |
| priv->usb_buf.val32 = cpu_to_le32(val); |
| ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), |
| REALTEK_USB_CMD_REQ, REALTEK_USB_WRITE, |
| addr, 0, &priv->usb_buf.val32, sizeof(u32), |
| RTW_USB_CONTROL_MSG_TIMEOUT); |
| mutex_unlock(&priv->usb_buf_mutex); |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_REG_WRITE) |
| dev_info(&udev->dev, "%s(%04x) = 0x%08x\n", |
| __func__, addr, val); |
| return ret; |
| } |
| |
| static int |
| rtl8xxxu_writeN(struct rtl8xxxu_priv *priv, u16 addr, u8 *buf, u16 len) |
| { |
| struct usb_device *udev = priv->udev; |
| int blocksize = priv->fops->writeN_block_size; |
| int ret, i, count, remainder; |
| |
| count = len / blocksize; |
| remainder = len % blocksize; |
| |
| for (i = 0; i < count; i++) { |
| ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), |
| REALTEK_USB_CMD_REQ, REALTEK_USB_WRITE, |
| addr, 0, buf, blocksize, |
| RTW_USB_CONTROL_MSG_TIMEOUT); |
| if (ret != blocksize) |
| goto write_error; |
| |
| addr += blocksize; |
| buf += blocksize; |
| } |
| |
| if (remainder) { |
| ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), |
| REALTEK_USB_CMD_REQ, REALTEK_USB_WRITE, |
| addr, 0, buf, remainder, |
| RTW_USB_CONTROL_MSG_TIMEOUT); |
| if (ret != remainder) |
| goto write_error; |
| } |
| |
| return len; |
| |
| write_error: |
| dev_info(&udev->dev, |
| "%s: Failed to write block at addr: %04x size: %04x\n", |
| __func__, addr, blocksize); |
| return -EAGAIN; |
| } |
| |
| static u32 rtl8xxxu_read_rfreg(struct rtl8xxxu_priv *priv, |
| enum rtl8xxxu_rfpath path, u8 reg) |
| { |
| u32 hssia, val32, retval; |
| |
| hssia = rtl8xxxu_read32(priv, REG_FPGA0_XA_HSSI_PARM2); |
| if (path != RF_A) |
| val32 = rtl8xxxu_read32(priv, rtl8xxxu_rfregs[path].hssiparm2); |
| else |
| val32 = hssia; |
| |
| val32 &= ~FPGA0_HSSI_PARM2_ADDR_MASK; |
| val32 |= (reg << FPGA0_HSSI_PARM2_ADDR_SHIFT); |
| val32 |= FPGA0_HSSI_PARM2_EDGE_READ; |
| hssia &= ~FPGA0_HSSI_PARM2_EDGE_READ; |
| rtl8xxxu_write32(priv, REG_FPGA0_XA_HSSI_PARM2, hssia); |
| |
| udelay(10); |
| |
| rtl8xxxu_write32(priv, rtl8xxxu_rfregs[path].hssiparm2, val32); |
| udelay(100); |
| |
| hssia |= FPGA0_HSSI_PARM2_EDGE_READ; |
| rtl8xxxu_write32(priv, REG_FPGA0_XA_HSSI_PARM2, hssia); |
| udelay(10); |
| |
| val32 = rtl8xxxu_read32(priv, rtl8xxxu_rfregs[path].hssiparm1); |
| if (val32 & FPGA0_HSSI_PARM1_PI) |
| retval = rtl8xxxu_read32(priv, rtl8xxxu_rfregs[path].hspiread); |
| else |
| retval = rtl8xxxu_read32(priv, rtl8xxxu_rfregs[path].lssiread); |
| |
| retval &= 0xfffff; |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_RFREG_READ) |
| dev_info(&priv->udev->dev, "%s(%02x) = 0x%06x\n", |
| __func__, reg, retval); |
| return retval; |
| } |
| |
| /* |
| * The RTL8723BU driver indicates that registers 0xb2 and 0xb6 can |
| * have write issues in high temperature conditions. We may have to |
| * retry writing them. |
| */ |
| static int rtl8xxxu_write_rfreg(struct rtl8xxxu_priv *priv, |
| enum rtl8xxxu_rfpath path, u8 reg, u32 data) |
| { |
| int ret, retval; |
| u32 dataaddr; |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_RFREG_WRITE) |
| dev_info(&priv->udev->dev, "%s(%02x) = 0x%06x\n", |
| __func__, reg, data); |
| |
| data &= FPGA0_LSSI_PARM_DATA_MASK; |
| dataaddr = (reg << FPGA0_LSSI_PARM_ADDR_SHIFT) | data; |
| |
| /* Use XB for path B */ |
| ret = rtl8xxxu_write32(priv, rtl8xxxu_rfregs[path].lssiparm, dataaddr); |
| if (ret != sizeof(dataaddr)) |
| retval = -EIO; |
| else |
| retval = 0; |
| |
| udelay(1); |
| |
| return retval; |
| } |
| |
| static int rtl8723a_h2c_cmd(struct rtl8xxxu_priv *priv, |
| struct h2c_cmd *h2c, int len) |
| { |
| struct device *dev = &priv->udev->dev; |
| int mbox_nr, retry, retval = 0; |
| int mbox_reg, mbox_ext_reg; |
| u8 val8; |
| |
| mutex_lock(&priv->h2c_mutex); |
| |
| mbox_nr = priv->next_mbox; |
| mbox_reg = REG_HMBOX_0 + (mbox_nr * 4); |
| mbox_ext_reg = priv->fops->mbox_ext_reg + |
| (mbox_nr * priv->fops->mbox_ext_width); |
| |
| /* |
| * MBOX ready? |
| */ |
| retry = 100; |
| do { |
| val8 = rtl8xxxu_read8(priv, REG_HMTFR); |
| if (!(val8 & BIT(mbox_nr))) |
| break; |
| } while (retry--); |
| |
| if (!retry) { |
| dev_info(dev, "%s: Mailbox busy\n", __func__); |
| retval = -EBUSY; |
| goto error; |
| } |
| |
| /* |
| * Need to swap as it's being swapped again by rtl8xxxu_write16/32() |
| */ |
| if (len > sizeof(u32)) { |
| if (priv->fops->mbox_ext_width == 4) { |
| rtl8xxxu_write32(priv, mbox_ext_reg, |
| le32_to_cpu(h2c->raw_wide.ext)); |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_H2C) |
| dev_info(dev, "H2C_EXT %08x\n", |
| le32_to_cpu(h2c->raw_wide.ext)); |
| } else { |
| rtl8xxxu_write16(priv, mbox_ext_reg, |
| le16_to_cpu(h2c->raw.ext)); |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_H2C) |
| dev_info(dev, "H2C_EXT %04x\n", |
| le16_to_cpu(h2c->raw.ext)); |
| } |
| } |
| rtl8xxxu_write32(priv, mbox_reg, le32_to_cpu(h2c->raw.data)); |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_H2C) |
| dev_info(dev, "H2C %08x\n", le32_to_cpu(h2c->raw.data)); |
| |
| priv->next_mbox = (mbox_nr + 1) % H2C_MAX_MBOX; |
| |
| error: |
| mutex_unlock(&priv->h2c_mutex); |
| return retval; |
| } |
| |
| static void rtl8723bu_write_btreg(struct rtl8xxxu_priv *priv, u8 reg, u8 data) |
| { |
| struct h2c_cmd h2c; |
| int reqnum = 0; |
| |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER; |
| h2c.bt_mp_oper.operreq = 0 | (reqnum << 4); |
| h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE; |
| h2c.bt_mp_oper.data = data; |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper)); |
| |
| reqnum++; |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER; |
| h2c.bt_mp_oper.operreq = 0 | (reqnum << 4); |
| h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE; |
| h2c.bt_mp_oper.addr = reg; |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper)); |
| } |
| |
| static void rtl8723a_enable_rf(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| u32 val32; |
| |
| val8 = rtl8xxxu_read8(priv, REG_SPS0_CTRL); |
| val8 |= BIT(0) | BIT(3); |
| rtl8xxxu_write8(priv, REG_SPS0_CTRL, val8); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_XAB_RF_PARM); |
| val32 &= ~(BIT(4) | BIT(5)); |
| val32 |= BIT(3); |
| if (priv->rf_paths == 2) { |
| val32 &= ~(BIT(20) | BIT(21)); |
| val32 |= BIT(19); |
| } |
| rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_PARM, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_TRX_PATH_ENABLE); |
| val32 &= ~OFDM_RF_PATH_TX_MASK; |
| if (priv->tx_paths == 2) |
| val32 |= OFDM_RF_PATH_TX_A | OFDM_RF_PATH_TX_B; |
| else if (priv->rtlchip == 0x8192c || priv->rtlchip == 0x8191c) |
| val32 |= OFDM_RF_PATH_TX_B; |
| else |
| val32 |= OFDM_RF_PATH_TX_A; |
| rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE); |
| val32 &= ~FPGA_RF_MODE_JAPAN; |
| rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32); |
| |
| if (priv->rf_paths == 2) |
| rtl8xxxu_write32(priv, REG_RX_WAIT_CCA, 0x63db25a0); |
| else |
| rtl8xxxu_write32(priv, REG_RX_WAIT_CCA, 0x631b25a0); |
| |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, 0x32d95); |
| if (priv->rf_paths == 2) |
| rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_AC, 0x32d95); |
| |
| rtl8xxxu_write8(priv, REG_TXPAUSE, 0x00); |
| } |
| |
| static void rtl8723b_enable_rf(struct rtl8xxxu_priv *priv) |
| { |
| } |
| |
| static void rtl8723a_disable_rf(struct rtl8xxxu_priv *priv) |
| { |
| u8 sps0; |
| u32 val32; |
| |
| rtl8xxxu_write8(priv, REG_TXPAUSE, 0xff); |
| |
| sps0 = rtl8xxxu_read8(priv, REG_SPS0_CTRL); |
| |
| /* RF RX code for preamble power saving */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_XAB_RF_PARM); |
| val32 &= ~(BIT(3) | BIT(4) | BIT(5)); |
| if (priv->rf_paths == 2) |
| val32 &= ~(BIT(19) | BIT(20) | BIT(21)); |
| rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_PARM, val32); |
| |
| /* Disable TX for four paths */ |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_TRX_PATH_ENABLE); |
| val32 &= ~OFDM_RF_PATH_TX_MASK; |
| rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, val32); |
| |
| /* Enable power saving */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE); |
| val32 |= FPGA_RF_MODE_JAPAN; |
| rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32); |
| |
| /* AFE control register to power down bits [30:22] */ |
| if (priv->rf_paths == 2) |
| rtl8xxxu_write32(priv, REG_RX_WAIT_CCA, 0x00db25a0); |
| else |
| rtl8xxxu_write32(priv, REG_RX_WAIT_CCA, 0x001b25a0); |
| |
| /* Power down RF module */ |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, 0); |
| if (priv->rf_paths == 2) |
| rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_AC, 0); |
| |
| sps0 &= ~(BIT(0) | BIT(3)); |
| rtl8xxxu_write8(priv, REG_SPS0_CTRL, sps0); |
| } |
| |
| |
| static void rtl8723a_stop_tx_beacon(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| |
| val8 = rtl8xxxu_read8(priv, REG_FWHW_TXQ_CTRL + 2); |
| val8 &= ~BIT(6); |
| rtl8xxxu_write8(priv, REG_FWHW_TXQ_CTRL + 2, val8); |
| |
| rtl8xxxu_write8(priv, REG_TBTT_PROHIBIT + 1, 0x64); |
| val8 = rtl8xxxu_read8(priv, REG_TBTT_PROHIBIT + 2); |
| val8 &= ~BIT(0); |
| rtl8xxxu_write8(priv, REG_TBTT_PROHIBIT + 2, val8); |
| } |
| |
| |
| /* |
| * The rtl8723a has 3 channel groups for it's efuse settings. It only |
| * supports the 2.4GHz band, so channels 1 - 14: |
| * group 0: channels 1 - 3 |
| * group 1: channels 4 - 9 |
| * group 2: channels 10 - 14 |
| * |
| * Note: We index from 0 in the code |
| */ |
| static int rtl8723a_channel_to_group(int channel) |
| { |
| int group; |
| |
| if (channel < 4) |
| group = 0; |
| else if (channel < 10) |
| group = 1; |
| else |
| group = 2; |
| |
| return group; |
| } |
| |
| static int rtl8723b_channel_to_group(int channel) |
| { |
| int group; |
| |
| if (channel < 3) |
| group = 0; |
| else if (channel < 6) |
| group = 1; |
| else if (channel < 9) |
| group = 2; |
| else if (channel < 12) |
| group = 3; |
| else |
| group = 4; |
| |
| return group; |
| } |
| |
| static void rtl8723au_config_channel(struct ieee80211_hw *hw) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| u32 val32, rsr; |
| u8 val8, opmode; |
| bool ht = true; |
| int sec_ch_above, channel; |
| int i; |
| |
| opmode = rtl8xxxu_read8(priv, REG_BW_OPMODE); |
| rsr = rtl8xxxu_read32(priv, REG_RESPONSE_RATE_SET); |
| channel = hw->conf.chandef.chan->hw_value; |
| |
| switch (hw->conf.chandef.width) { |
| case NL80211_CHAN_WIDTH_20_NOHT: |
| ht = false; |
| case NL80211_CHAN_WIDTH_20: |
| opmode |= BW_OPMODE_20MHZ; |
| rtl8xxxu_write8(priv, REG_BW_OPMODE, opmode); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE); |
| val32 &= ~FPGA_RF_MODE; |
| rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA1_RF_MODE); |
| val32 &= ~FPGA_RF_MODE; |
| rtl8xxxu_write32(priv, REG_FPGA1_RF_MODE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_ANALOG2); |
| val32 |= FPGA0_ANALOG2_20MHZ; |
| rtl8xxxu_write32(priv, REG_FPGA0_ANALOG2, val32); |
| break; |
| case NL80211_CHAN_WIDTH_40: |
| if (hw->conf.chandef.center_freq1 > |
| hw->conf.chandef.chan->center_freq) { |
| sec_ch_above = 1; |
| channel += 2; |
| } else { |
| sec_ch_above = 0; |
| channel -= 2; |
| } |
| |
| opmode &= ~BW_OPMODE_20MHZ; |
| rtl8xxxu_write8(priv, REG_BW_OPMODE, opmode); |
| rsr &= ~RSR_RSC_BANDWIDTH_40M; |
| if (sec_ch_above) |
| rsr |= RSR_RSC_UPPER_SUB_CHANNEL; |
| else |
| rsr |= RSR_RSC_LOWER_SUB_CHANNEL; |
| rtl8xxxu_write32(priv, REG_RESPONSE_RATE_SET, rsr); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE); |
| val32 |= FPGA_RF_MODE; |
| rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA1_RF_MODE); |
| val32 |= FPGA_RF_MODE; |
| rtl8xxxu_write32(priv, REG_FPGA1_RF_MODE, val32); |
| |
| /* |
| * Set Control channel to upper or lower. These settings |
| * are required only for 40MHz |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_CCK0_SYSTEM); |
| val32 &= ~CCK0_SIDEBAND; |
| if (!sec_ch_above) |
| val32 |= CCK0_SIDEBAND; |
| rtl8xxxu_write32(priv, REG_CCK0_SYSTEM, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM1_LSTF); |
| val32 &= ~OFDM_LSTF_PRIME_CH_MASK; /* 0xc00 */ |
| if (sec_ch_above) |
| val32 |= OFDM_LSTF_PRIME_CH_LOW; |
| else |
| val32 |= OFDM_LSTF_PRIME_CH_HIGH; |
| rtl8xxxu_write32(priv, REG_OFDM1_LSTF, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_ANALOG2); |
| val32 &= ~FPGA0_ANALOG2_20MHZ; |
| rtl8xxxu_write32(priv, REG_FPGA0_ANALOG2, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_POWER_SAVE); |
| val32 &= ~(FPGA0_PS_LOWER_CHANNEL | FPGA0_PS_UPPER_CHANNEL); |
| if (sec_ch_above) |
| val32 |= FPGA0_PS_UPPER_CHANNEL; |
| else |
| val32 |= FPGA0_PS_LOWER_CHANNEL; |
| rtl8xxxu_write32(priv, REG_FPGA0_POWER_SAVE, val32); |
| break; |
| |
| default: |
| break; |
| } |
| |
| for (i = RF_A; i < priv->rf_paths; i++) { |
| val32 = rtl8xxxu_read_rfreg(priv, i, RF6052_REG_MODE_AG); |
| val32 &= ~MODE_AG_CHANNEL_MASK; |
| val32 |= channel; |
| rtl8xxxu_write_rfreg(priv, i, RF6052_REG_MODE_AG, val32); |
| } |
| |
| if (ht) |
| val8 = 0x0e; |
| else |
| val8 = 0x0a; |
| |
| rtl8xxxu_write8(priv, REG_SIFS_CCK + 1, val8); |
| rtl8xxxu_write8(priv, REG_SIFS_OFDM + 1, val8); |
| |
| rtl8xxxu_write16(priv, REG_R2T_SIFS, 0x0808); |
| rtl8xxxu_write16(priv, REG_T2T_SIFS, 0x0a0a); |
| |
| for (i = RF_A; i < priv->rf_paths; i++) { |
| val32 = rtl8xxxu_read_rfreg(priv, i, RF6052_REG_MODE_AG); |
| if (hw->conf.chandef.width == NL80211_CHAN_WIDTH_40) |
| val32 &= ~MODE_AG_CHANNEL_20MHZ; |
| else |
| val32 |= MODE_AG_CHANNEL_20MHZ; |
| rtl8xxxu_write_rfreg(priv, i, RF6052_REG_MODE_AG, val32); |
| } |
| } |
| |
| static void rtl8723bu_config_channel(struct ieee80211_hw *hw) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| u32 val32, rsr; |
| u8 val8, subchannel; |
| u16 rf_mode_bw; |
| bool ht = true; |
| int sec_ch_above, channel; |
| int i; |
| |
| rf_mode_bw = rtl8xxxu_read16(priv, REG_WMAC_TRXPTCL_CTL); |
| rf_mode_bw &= ~WMAC_TRXPTCL_CTL_BW_MASK; |
| rsr = rtl8xxxu_read32(priv, REG_RESPONSE_RATE_SET); |
| channel = hw->conf.chandef.chan->hw_value; |
| |
| /* Hack */ |
| subchannel = 0; |
| |
| switch (hw->conf.chandef.width) { |
| case NL80211_CHAN_WIDTH_20_NOHT: |
| ht = false; |
| case NL80211_CHAN_WIDTH_20: |
| rf_mode_bw |= WMAC_TRXPTCL_CTL_BW_20; |
| subchannel = 0; |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE); |
| val32 &= ~FPGA_RF_MODE; |
| rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA1_RF_MODE); |
| val32 &= ~FPGA_RF_MODE; |
| rtl8xxxu_write32(priv, REG_FPGA1_RF_MODE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_TX_PSDO_NOISE_WEIGHT); |
| val32 &= ~(BIT(30) | BIT(31)); |
| rtl8xxxu_write32(priv, REG_OFDM0_TX_PSDO_NOISE_WEIGHT, val32); |
| |
| break; |
| case NL80211_CHAN_WIDTH_40: |
| rf_mode_bw |= WMAC_TRXPTCL_CTL_BW_40; |
| |
| if (hw->conf.chandef.center_freq1 > |
| hw->conf.chandef.chan->center_freq) { |
| sec_ch_above = 1; |
| channel += 2; |
| } else { |
| sec_ch_above = 0; |
| channel -= 2; |
| } |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE); |
| val32 |= FPGA_RF_MODE; |
| rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA1_RF_MODE); |
| val32 |= FPGA_RF_MODE; |
| rtl8xxxu_write32(priv, REG_FPGA1_RF_MODE, val32); |
| |
| /* |
| * Set Control channel to upper or lower. These settings |
| * are required only for 40MHz |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_CCK0_SYSTEM); |
| val32 &= ~CCK0_SIDEBAND; |
| if (!sec_ch_above) |
| val32 |= CCK0_SIDEBAND; |
| rtl8xxxu_write32(priv, REG_CCK0_SYSTEM, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM1_LSTF); |
| val32 &= ~OFDM_LSTF_PRIME_CH_MASK; /* 0xc00 */ |
| if (sec_ch_above) |
| val32 |= OFDM_LSTF_PRIME_CH_LOW; |
| else |
| val32 |= OFDM_LSTF_PRIME_CH_HIGH; |
| rtl8xxxu_write32(priv, REG_OFDM1_LSTF, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_POWER_SAVE); |
| val32 &= ~(FPGA0_PS_LOWER_CHANNEL | FPGA0_PS_UPPER_CHANNEL); |
| if (sec_ch_above) |
| val32 |= FPGA0_PS_UPPER_CHANNEL; |
| else |
| val32 |= FPGA0_PS_LOWER_CHANNEL; |
| rtl8xxxu_write32(priv, REG_FPGA0_POWER_SAVE, val32); |
| break; |
| case NL80211_CHAN_WIDTH_80: |
| rf_mode_bw |= WMAC_TRXPTCL_CTL_BW_80; |
| break; |
| default: |
| break; |
| } |
| |
| for (i = RF_A; i < priv->rf_paths; i++) { |
| val32 = rtl8xxxu_read_rfreg(priv, i, RF6052_REG_MODE_AG); |
| val32 &= ~MODE_AG_CHANNEL_MASK; |
| val32 |= channel; |
| rtl8xxxu_write_rfreg(priv, i, RF6052_REG_MODE_AG, val32); |
| } |
| |
| rtl8xxxu_write16(priv, REG_WMAC_TRXPTCL_CTL, rf_mode_bw); |
| rtl8xxxu_write8(priv, REG_DATA_SUBCHANNEL, subchannel); |
| |
| if (ht) |
| val8 = 0x0e; |
| else |
| val8 = 0x0a; |
| |
| rtl8xxxu_write8(priv, REG_SIFS_CCK + 1, val8); |
| rtl8xxxu_write8(priv, REG_SIFS_OFDM + 1, val8); |
| |
| rtl8xxxu_write16(priv, REG_R2T_SIFS, 0x0808); |
| rtl8xxxu_write16(priv, REG_T2T_SIFS, 0x0a0a); |
| |
| for (i = RF_A; i < priv->rf_paths; i++) { |
| val32 = rtl8xxxu_read_rfreg(priv, i, RF6052_REG_MODE_AG); |
| val32 &= ~MODE_AG_BW_MASK; |
| switch(hw->conf.chandef.width) { |
| case NL80211_CHAN_WIDTH_80: |
| val32 |= MODE_AG_BW_80MHZ_8723B; |
| break; |
| case NL80211_CHAN_WIDTH_40: |
| val32 |= MODE_AG_BW_40MHZ_8723B; |
| break; |
| default: |
| val32 |= MODE_AG_BW_20MHZ_8723B; |
| break; |
| } |
| rtl8xxxu_write_rfreg(priv, i, RF6052_REG_MODE_AG, val32); |
| } |
| } |
| |
| static void |
| rtl8723a_set_tx_power(struct rtl8xxxu_priv *priv, int channel, bool ht40) |
| { |
| u8 cck[RTL8723A_MAX_RF_PATHS], ofdm[RTL8723A_MAX_RF_PATHS]; |
| u8 ofdmbase[RTL8723A_MAX_RF_PATHS], mcsbase[RTL8723A_MAX_RF_PATHS]; |
| u32 val32, ofdm_a, ofdm_b, mcs_a, mcs_b; |
| u8 val8; |
| int group, i; |
| |
| group = rtl8723a_channel_to_group(channel); |
| |
| cck[0] = priv->cck_tx_power_index_A[group]; |
| cck[1] = priv->cck_tx_power_index_B[group]; |
| |
| ofdm[0] = priv->ht40_1s_tx_power_index_A[group]; |
| ofdm[1] = priv->ht40_1s_tx_power_index_B[group]; |
| |
| ofdmbase[0] = ofdm[0] + priv->ofdm_tx_power_index_diff[group].a; |
| ofdmbase[1] = ofdm[1] + priv->ofdm_tx_power_index_diff[group].b; |
| |
| mcsbase[0] = ofdm[0]; |
| mcsbase[1] = ofdm[1]; |
| if (!ht40) { |
| mcsbase[0] += priv->ht20_tx_power_index_diff[group].a; |
| mcsbase[1] += priv->ht20_tx_power_index_diff[group].b; |
| } |
| |
| if (priv->tx_paths > 1) { |
| if (ofdm[0] > priv->ht40_2s_tx_power_index_diff[group].a) |
| ofdm[0] -= priv->ht40_2s_tx_power_index_diff[group].a; |
| if (ofdm[1] > priv->ht40_2s_tx_power_index_diff[group].b) |
| ofdm[1] -= priv->ht40_2s_tx_power_index_diff[group].b; |
| } |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_CHANNEL) |
| dev_info(&priv->udev->dev, |
| "%s: Setting TX power CCK A: %02x, " |
| "CCK B: %02x, OFDM A: %02x, OFDM B: %02x\n", |
| __func__, cck[0], cck[1], ofdm[0], ofdm[1]); |
| |
| for (i = 0; i < RTL8723A_MAX_RF_PATHS; i++) { |
| if (cck[i] > RF6052_MAX_TX_PWR) |
| cck[i] = RF6052_MAX_TX_PWR; |
| if (ofdm[i] > RF6052_MAX_TX_PWR) |
| ofdm[i] = RF6052_MAX_TX_PWR; |
| } |
| |
| val32 = rtl8xxxu_read32(priv, REG_TX_AGC_A_CCK1_MCS32); |
| val32 &= 0xffff00ff; |
| val32 |= (cck[0] << 8); |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_CCK1_MCS32, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11); |
| val32 &= 0xff; |
| val32 |= ((cck[0] << 8) | (cck[0] << 16) | (cck[0] << 24)); |
| rtl8xxxu_write32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11); |
| val32 &= 0xffffff00; |
| val32 |= cck[1]; |
| rtl8xxxu_write32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_TX_AGC_B_CCK1_55_MCS32); |
| val32 &= 0xff; |
| val32 |= ((cck[1] << 8) | (cck[1] << 16) | (cck[1] << 24)); |
| rtl8xxxu_write32(priv, REG_TX_AGC_B_CCK1_55_MCS32, val32); |
| |
| ofdm_a = ofdmbase[0] | ofdmbase[0] << 8 | |
| ofdmbase[0] << 16 | ofdmbase[0] << 24; |
| ofdm_b = ofdmbase[1] | ofdmbase[1] << 8 | |
| ofdmbase[1] << 16 | ofdmbase[1] << 24; |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE18_06, ofdm_a); |
| rtl8xxxu_write32(priv, REG_TX_AGC_B_RATE18_06, ofdm_b); |
| |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE54_24, ofdm_a); |
| rtl8xxxu_write32(priv, REG_TX_AGC_B_RATE54_24, ofdm_b); |
| |
| mcs_a = mcsbase[0] | mcsbase[0] << 8 | |
| mcsbase[0] << 16 | mcsbase[0] << 24; |
| mcs_b = mcsbase[1] | mcsbase[1] << 8 | |
| mcsbase[1] << 16 | mcsbase[1] << 24; |
| |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS03_MCS00, mcs_a); |
| rtl8xxxu_write32(priv, REG_TX_AGC_B_MCS03_MCS00, mcs_b); |
| |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS07_MCS04, mcs_a); |
| rtl8xxxu_write32(priv, REG_TX_AGC_B_MCS07_MCS04, mcs_b); |
| |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS11_MCS08, mcs_a); |
| rtl8xxxu_write32(priv, REG_TX_AGC_B_MCS11_MCS08, mcs_b); |
| |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS15_MCS12, mcs_a); |
| for (i = 0; i < 3; i++) { |
| if (i != 2) |
| val8 = (mcsbase[0] > 8) ? (mcsbase[0] - 8) : 0; |
| else |
| val8 = (mcsbase[0] > 6) ? (mcsbase[0] - 6) : 0; |
| rtl8xxxu_write8(priv, REG_OFDM0_XC_TX_IQ_IMBALANCE + i, val8); |
| } |
| rtl8xxxu_write32(priv, REG_TX_AGC_B_MCS15_MCS12, mcs_b); |
| for (i = 0; i < 3; i++) { |
| if (i != 2) |
| val8 = (mcsbase[1] > 8) ? (mcsbase[1] - 8) : 0; |
| else |
| val8 = (mcsbase[1] > 6) ? (mcsbase[1] - 6) : 0; |
| rtl8xxxu_write8(priv, REG_OFDM0_XD_TX_IQ_IMBALANCE + i, val8); |
| } |
| } |
| |
| static void |
| rtl8723b_set_tx_power(struct rtl8xxxu_priv *priv, int channel, bool ht40) |
| { |
| u32 val32, ofdm, mcs; |
| u8 cck, ofdmbase, mcsbase; |
| int group, tx_idx; |
| |
| tx_idx = 0; |
| group = rtl8723b_channel_to_group(channel); |
| |
| cck = priv->cck_tx_power_index_B[group]; |
| val32 = rtl8xxxu_read32(priv, REG_TX_AGC_A_CCK1_MCS32); |
| val32 &= 0xffff00ff; |
| val32 |= (cck << 8); |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_CCK1_MCS32, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11); |
| val32 &= 0xff; |
| val32 |= ((cck << 8) | (cck << 16) | (cck << 24)); |
| rtl8xxxu_write32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11, val32); |
| |
| ofdmbase = priv->ht40_1s_tx_power_index_B[group]; |
| ofdmbase += priv->ofdm_tx_power_diff[tx_idx].b; |
| ofdm = ofdmbase | ofdmbase << 8 | ofdmbase << 16 | ofdmbase << 24; |
| |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE18_06, ofdm); |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE54_24, ofdm); |
| |
| mcsbase = priv->ht40_1s_tx_power_index_B[group]; |
| if (ht40) |
| mcsbase += priv->ht40_tx_power_diff[tx_idx++].b; |
| else |
| mcsbase += priv->ht20_tx_power_diff[tx_idx++].b; |
| mcs = mcsbase | mcsbase << 8 | mcsbase << 16 | mcsbase << 24; |
| |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS03_MCS00, mcs); |
| rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS07_MCS04, mcs); |
| } |
| |
| static void rtl8xxxu_set_linktype(struct rtl8xxxu_priv *priv, |
| enum nl80211_iftype linktype) |
| { |
| u8 val8; |
| |
| val8 = rtl8xxxu_read8(priv, REG_MSR); |
| val8 &= ~MSR_LINKTYPE_MASK; |
| |
| switch (linktype) { |
| case NL80211_IFTYPE_UNSPECIFIED: |
| val8 |= MSR_LINKTYPE_NONE; |
| break; |
| case NL80211_IFTYPE_ADHOC: |
| val8 |= MSR_LINKTYPE_ADHOC; |
| break; |
| case NL80211_IFTYPE_STATION: |
| val8 |= MSR_LINKTYPE_STATION; |
| break; |
| case NL80211_IFTYPE_AP: |
| val8 |= MSR_LINKTYPE_AP; |
| break; |
| default: |
| goto out; |
| } |
| |
| rtl8xxxu_write8(priv, REG_MSR, val8); |
| out: |
| return; |
| } |
| |
| static void |
| rtl8xxxu_set_retry(struct rtl8xxxu_priv *priv, u16 short_retry, u16 long_retry) |
| { |
| u16 val16; |
| |
| val16 = ((short_retry << RETRY_LIMIT_SHORT_SHIFT) & |
| RETRY_LIMIT_SHORT_MASK) | |
| ((long_retry << RETRY_LIMIT_LONG_SHIFT) & |
| RETRY_LIMIT_LONG_MASK); |
| |
| rtl8xxxu_write16(priv, REG_RETRY_LIMIT, val16); |
| } |
| |
| static void |
| rtl8xxxu_set_spec_sifs(struct rtl8xxxu_priv *priv, u16 cck, u16 ofdm) |
| { |
| u16 val16; |
| |
| val16 = ((cck << SPEC_SIFS_CCK_SHIFT) & SPEC_SIFS_CCK_MASK) | |
| ((ofdm << SPEC_SIFS_OFDM_SHIFT) & SPEC_SIFS_OFDM_MASK); |
| |
| rtl8xxxu_write16(priv, REG_SPEC_SIFS, val16); |
| } |
| |
| static void rtl8xxxu_print_chipinfo(struct rtl8xxxu_priv *priv) |
| { |
| struct device *dev = &priv->udev->dev; |
| char *cut; |
| |
| switch (priv->chip_cut) { |
| case 0: |
| cut = "A"; |
| break; |
| case 1: |
| cut = "B"; |
| break; |
| case 2: |
| cut = "C"; |
| break; |
| case 3: |
| cut = "D"; |
| break; |
| case 4: |
| cut = "E"; |
| break; |
| default: |
| cut = "unknown"; |
| } |
| |
| dev_info(dev, |
| "RTL%s rev %s (%s) %iT%iR, TX queues %i, WiFi=%i, BT=%i, GPS=%i, HI PA=%i\n", |
| priv->chip_name, cut, priv->chip_vendor, priv->tx_paths, |
| priv->rx_paths, priv->ep_tx_count, priv->has_wifi, |
| priv->has_bluetooth, priv->has_gps, priv->hi_pa); |
| |
| dev_info(dev, "RTL%s MAC: %pM\n", priv->chip_name, priv->mac_addr); |
| } |
| |
| static int rtl8xxxu_identify_chip(struct rtl8xxxu_priv *priv) |
| { |
| struct device *dev = &priv->udev->dev; |
| u32 val32, bonding; |
| u16 val16; |
| |
| val32 = rtl8xxxu_read32(priv, REG_SYS_CFG); |
| priv->chip_cut = (val32 & SYS_CFG_CHIP_VERSION_MASK) >> |
| SYS_CFG_CHIP_VERSION_SHIFT; |
| if (val32 & SYS_CFG_TRP_VAUX_EN) { |
| dev_info(dev, "Unsupported test chip\n"); |
| return -ENOTSUPP; |
| } |
| |
| if (val32 & SYS_CFG_BT_FUNC) { |
| if (priv->chip_cut >= 3) { |
| sprintf(priv->chip_name, "8723BU"); |
| priv->rtlchip = 0x8723b; |
| } else { |
| sprintf(priv->chip_name, "8723AU"); |
| priv->usb_interrupts = 1; |
| priv->rtlchip = 0x8723a; |
| } |
| |
| priv->rf_paths = 1; |
| priv->rx_paths = 1; |
| priv->tx_paths = 1; |
| |
| val32 = rtl8xxxu_read32(priv, REG_MULTI_FUNC_CTRL); |
| if (val32 & MULTI_WIFI_FUNC_EN) |
| priv->has_wifi = 1; |
| if (val32 & MULTI_BT_FUNC_EN) |
| priv->has_bluetooth = 1; |
| if (val32 & MULTI_GPS_FUNC_EN) |
| priv->has_gps = 1; |
| priv->is_multi_func = 1; |
| } else if (val32 & SYS_CFG_TYPE_ID) { |
| bonding = rtl8xxxu_read32(priv, REG_HPON_FSM); |
| bonding &= HPON_FSM_BONDING_MASK; |
| if (priv->chip_cut >= 3) { |
| if (bonding == HPON_FSM_BONDING_1T2R) { |
| sprintf(priv->chip_name, "8191EU"); |
| priv->rf_paths = 2; |
| priv->rx_paths = 2; |
| priv->tx_paths = 1; |
| priv->rtlchip = 0x8191e; |
| } else { |
| sprintf(priv->chip_name, "8192EU"); |
| priv->rf_paths = 2; |
| priv->rx_paths = 2; |
| priv->tx_paths = 2; |
| priv->rtlchip = 0x8192e; |
| } |
| } else if (bonding == HPON_FSM_BONDING_1T2R) { |
| sprintf(priv->chip_name, "8191CU"); |
| priv->rf_paths = 2; |
| priv->rx_paths = 2; |
| priv->tx_paths = 1; |
| priv->usb_interrupts = 1; |
| priv->rtlchip = 0x8191c; |
| } else { |
| sprintf(priv->chip_name, "8192CU"); |
| priv->rf_paths = 2; |
| priv->rx_paths = 2; |
| priv->tx_paths = 2; |
| priv->usb_interrupts = 1; |
| priv->rtlchip = 0x8192c; |
| } |
| priv->has_wifi = 1; |
| } else { |
| sprintf(priv->chip_name, "8188CU"); |
| priv->rf_paths = 1; |
| priv->rx_paths = 1; |
| priv->tx_paths = 1; |
| priv->rtlchip = 0x8188c; |
| priv->usb_interrupts = 1; |
| priv->has_wifi = 1; |
| } |
| |
| switch (priv->rtlchip) { |
| case 0x8188e: |
| case 0x8192e: |
| case 0x8723b: |
| switch (val32 & SYS_CFG_VENDOR_EXT_MASK) { |
| case SYS_CFG_VENDOR_ID_TSMC: |
| sprintf(priv->chip_vendor, "TSMC"); |
| break; |
| case SYS_CFG_VENDOR_ID_SMIC: |
| sprintf(priv->chip_vendor, "SMIC"); |
| priv->vendor_smic = 1; |
| break; |
| case SYS_CFG_VENDOR_ID_UMC: |
| sprintf(priv->chip_vendor, "UMC"); |
| priv->vendor_umc = 1; |
| break; |
| default: |
| sprintf(priv->chip_vendor, "unknown"); |
| } |
| break; |
| default: |
| if (val32 & SYS_CFG_VENDOR_ID) { |
| sprintf(priv->chip_vendor, "UMC"); |
| priv->vendor_umc = 1; |
| } else { |
| sprintf(priv->chip_vendor, "TSMC"); |
| } |
| } |
| |
| val32 = rtl8xxxu_read32(priv, REG_GPIO_OUTSTS); |
| priv->rom_rev = (val32 & GPIO_RF_RL_ID) >> 28; |
| |
| val16 = rtl8xxxu_read16(priv, REG_NORMAL_SIE_EP_TX); |
| if (val16 & NORMAL_SIE_EP_TX_HIGH_MASK) { |
| priv->ep_tx_high_queue = 1; |
| priv->ep_tx_count++; |
| } |
| |
| if (val16 & NORMAL_SIE_EP_TX_NORMAL_MASK) { |
| priv->ep_tx_normal_queue = 1; |
| priv->ep_tx_count++; |
| } |
| |
| if (val16 & NORMAL_SIE_EP_TX_LOW_MASK) { |
| priv->ep_tx_low_queue = 1; |
| priv->ep_tx_count++; |
| } |
| |
| /* |
| * Fallback for devices that do not provide REG_NORMAL_SIE_EP_TX |
| */ |
| if (!priv->ep_tx_count) { |
| switch (priv->nr_out_eps) { |
| case 4: |
| case 3: |
| priv->ep_tx_low_queue = 1; |
| priv->ep_tx_count++; |
| case 2: |
| priv->ep_tx_normal_queue = 1; |
| priv->ep_tx_count++; |
| case 1: |
| priv->ep_tx_high_queue = 1; |
| priv->ep_tx_count++; |
| break; |
| default: |
| dev_info(dev, "Unsupported USB TX end-points\n"); |
| return -ENOTSUPP; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int rtl8723au_parse_efuse(struct rtl8xxxu_priv *priv) |
| { |
| struct rtl8723au_efuse *efuse = &priv->efuse_wifi.efuse8723; |
| |
| if (efuse->rtl_id != cpu_to_le16(0x8129)) |
| return -EINVAL; |
| |
| ether_addr_copy(priv->mac_addr, efuse->mac_addr); |
| |
| memcpy(priv->cck_tx_power_index_A, |
| efuse->cck_tx_power_index_A, |
| sizeof(efuse->cck_tx_power_index_A)); |
| memcpy(priv->cck_tx_power_index_B, |
| efuse->cck_tx_power_index_B, |
| sizeof(efuse->cck_tx_power_index_B)); |
| |
| memcpy(priv->ht40_1s_tx_power_index_A, |
| efuse->ht40_1s_tx_power_index_A, |
| sizeof(efuse->ht40_1s_tx_power_index_A)); |
| memcpy(priv->ht40_1s_tx_power_index_B, |
| efuse->ht40_1s_tx_power_index_B, |
| sizeof(efuse->ht40_1s_tx_power_index_B)); |
| |
| memcpy(priv->ht20_tx_power_index_diff, |
| efuse->ht20_tx_power_index_diff, |
| sizeof(efuse->ht20_tx_power_index_diff)); |
| memcpy(priv->ofdm_tx_power_index_diff, |
| efuse->ofdm_tx_power_index_diff, |
| sizeof(efuse->ofdm_tx_power_index_diff)); |
| |
| memcpy(priv->ht40_max_power_offset, |
| efuse->ht40_max_power_offset, |
| sizeof(efuse->ht40_max_power_offset)); |
| memcpy(priv->ht20_max_power_offset, |
| efuse->ht20_max_power_offset, |
| sizeof(efuse->ht20_max_power_offset)); |
| |
| if (priv->efuse_wifi.efuse8723.version >= 0x01) { |
| priv->has_xtalk = 1; |
| priv->xtalk = priv->efuse_wifi.efuse8723.xtal_k & 0x3f; |
| } |
| dev_info(&priv->udev->dev, "Vendor: %.7s\n", |
| efuse->vendor_name); |
| dev_info(&priv->udev->dev, "Product: %.41s\n", |
| efuse->device_name); |
| return 0; |
| } |
| |
| static int rtl8723bu_parse_efuse(struct rtl8xxxu_priv *priv) |
| { |
| struct rtl8723bu_efuse *efuse = &priv->efuse_wifi.efuse8723bu; |
| int i; |
| |
| if (efuse->rtl_id != cpu_to_le16(0x8129)) |
| return -EINVAL; |
| |
| ether_addr_copy(priv->mac_addr, efuse->mac_addr); |
| |
| memcpy(priv->cck_tx_power_index_A, efuse->tx_power_index_A.cck_base, |
| sizeof(efuse->tx_power_index_A.cck_base)); |
| memcpy(priv->cck_tx_power_index_B, efuse->tx_power_index_B.cck_base, |
| sizeof(efuse->tx_power_index_B.cck_base)); |
| |
| memcpy(priv->ht40_1s_tx_power_index_A, |
| efuse->tx_power_index_A.ht40_base, |
| sizeof(efuse->tx_power_index_A.ht40_base)); |
| memcpy(priv->ht40_1s_tx_power_index_B, |
| efuse->tx_power_index_B.ht40_base, |
| sizeof(efuse->tx_power_index_B.ht40_base)); |
| |
| priv->ofdm_tx_power_diff[0].a = |
| efuse->tx_power_index_A.ht20_ofdm_1s_diff.a; |
| priv->ofdm_tx_power_diff[0].b = |
| efuse->tx_power_index_B.ht20_ofdm_1s_diff.a; |
| |
| priv->ht20_tx_power_diff[0].a = |
| efuse->tx_power_index_A.ht20_ofdm_1s_diff.b; |
| priv->ht20_tx_power_diff[0].b = |
| efuse->tx_power_index_B.ht20_ofdm_1s_diff.b; |
| |
| priv->ht40_tx_power_diff[0].a = 0; |
| priv->ht40_tx_power_diff[0].b = 0; |
| |
| for (i = 1; i < RTL8723B_TX_COUNT; i++) { |
| priv->ofdm_tx_power_diff[i].a = |
| efuse->tx_power_index_A.pwr_diff[i - 1].ofdm; |
| priv->ofdm_tx_power_diff[i].b = |
| efuse->tx_power_index_B.pwr_diff[i - 1].ofdm; |
| |
| priv->ht20_tx_power_diff[i].a = |
| efuse->tx_power_index_A.pwr_diff[i - 1].ht20; |
| priv->ht20_tx_power_diff[i].b = |
| efuse->tx_power_index_B.pwr_diff[i - 1].ht20; |
| |
| priv->ht40_tx_power_diff[i].a = |
| efuse->tx_power_index_A.pwr_diff[i - 1].ht40; |
| priv->ht40_tx_power_diff[i].b = |
| efuse->tx_power_index_B.pwr_diff[i - 1].ht40; |
| } |
| |
| priv->has_xtalk = 1; |
| priv->xtalk = priv->efuse_wifi.efuse8723bu.xtal_k & 0x3f; |
| |
| dev_info(&priv->udev->dev, "Vendor: %.7s\n", efuse->vendor_name); |
| dev_info(&priv->udev->dev, "Product: %.41s\n", efuse->device_name); |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_EFUSE) { |
| int i; |
| unsigned char *raw = priv->efuse_wifi.raw; |
| |
| dev_info(&priv->udev->dev, |
| "%s: dumping efuse (0x%02zx bytes):\n", |
| __func__, sizeof(struct rtl8723bu_efuse)); |
| for (i = 0; i < sizeof(struct rtl8723bu_efuse); i += 8) { |
| dev_info(&priv->udev->dev, "%02x: " |
| "%02x %02x %02x %02x %02x %02x %02x %02x\n", i, |
| raw[i], raw[i + 1], raw[i + 2], |
| raw[i + 3], raw[i + 4], raw[i + 5], |
| raw[i + 6], raw[i + 7]); |
| } |
| } |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_RTL8XXXU_UNTESTED |
| |
| static int rtl8192cu_parse_efuse(struct rtl8xxxu_priv *priv) |
| { |
| struct rtl8192cu_efuse *efuse = &priv->efuse_wifi.efuse8192; |
| int i; |
| |
| if (efuse->rtl_id != cpu_to_le16(0x8129)) |
| return -EINVAL; |
| |
| ether_addr_copy(priv->mac_addr, efuse->mac_addr); |
| |
| memcpy(priv->cck_tx_power_index_A, |
| efuse->cck_tx_power_index_A, |
| sizeof(efuse->cck_tx_power_index_A)); |
| memcpy(priv->cck_tx_power_index_B, |
| efuse->cck_tx_power_index_B, |
| sizeof(efuse->cck_tx_power_index_B)); |
| |
| memcpy(priv->ht40_1s_tx_power_index_A, |
| efuse->ht40_1s_tx_power_index_A, |
| sizeof(efuse->ht40_1s_tx_power_index_A)); |
| memcpy(priv->ht40_1s_tx_power_index_B, |
| efuse->ht40_1s_tx_power_index_B, |
| sizeof(efuse->ht40_1s_tx_power_index_B)); |
| memcpy(priv->ht40_2s_tx_power_index_diff, |
| efuse->ht40_2s_tx_power_index_diff, |
| sizeof(efuse->ht40_2s_tx_power_index_diff)); |
| |
| memcpy(priv->ht20_tx_power_index_diff, |
| efuse->ht20_tx_power_index_diff, |
| sizeof(efuse->ht20_tx_power_index_diff)); |
| memcpy(priv->ofdm_tx_power_index_diff, |
| efuse->ofdm_tx_power_index_diff, |
| sizeof(efuse->ofdm_tx_power_index_diff)); |
| |
| memcpy(priv->ht40_max_power_offset, |
| efuse->ht40_max_power_offset, |
| sizeof(efuse->ht40_max_power_offset)); |
| memcpy(priv->ht20_max_power_offset, |
| efuse->ht20_max_power_offset, |
| sizeof(efuse->ht20_max_power_offset)); |
| |
| dev_info(&priv->udev->dev, "Vendor: %.7s\n", |
| efuse->vendor_name); |
| dev_info(&priv->udev->dev, "Product: %.20s\n", |
| efuse->device_name); |
| |
| if (efuse->rf_regulatory & 0x20) { |
| sprintf(priv->chip_name, "8188RU"); |
| priv->hi_pa = 1; |
| } |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_EFUSE) { |
| unsigned char *raw = priv->efuse_wifi.raw; |
| |
| dev_info(&priv->udev->dev, |
| "%s: dumping efuse (0x%02zx bytes):\n", |
| __func__, sizeof(struct rtl8192cu_efuse)); |
| for (i = 0; i < sizeof(struct rtl8192cu_efuse); i += 8) { |
| dev_info(&priv->udev->dev, "%02x: " |
| "%02x %02x %02x %02x %02x %02x %02x %02x\n", i, |
| raw[i], raw[i + 1], raw[i + 2], |
| raw[i + 3], raw[i + 4], raw[i + 5], |
| raw[i + 6], raw[i + 7]); |
| } |
| } |
| return 0; |
| } |
| |
| #endif |
| |
| static int rtl8192eu_parse_efuse(struct rtl8xxxu_priv *priv) |
| { |
| struct rtl8192eu_efuse *efuse = &priv->efuse_wifi.efuse8192eu; |
| int i; |
| |
| if (efuse->rtl_id != cpu_to_le16(0x8129)) |
| return -EINVAL; |
| |
| ether_addr_copy(priv->mac_addr, efuse->mac_addr); |
| |
| priv->has_xtalk = 1; |
| priv->xtalk = priv->efuse_wifi.efuse8192eu.xtal_k & 0x3f; |
| |
| dev_info(&priv->udev->dev, "Vendor: %.7s\n", efuse->vendor_name); |
| dev_info(&priv->udev->dev, "Product: %.11s\n", efuse->device_name); |
| dev_info(&priv->udev->dev, "Serial: %.11s\n", efuse->serial); |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_EFUSE) { |
| unsigned char *raw = priv->efuse_wifi.raw; |
| |
| dev_info(&priv->udev->dev, |
| "%s: dumping efuse (0x%02zx bytes):\n", |
| __func__, sizeof(struct rtl8192eu_efuse)); |
| for (i = 0; i < sizeof(struct rtl8192eu_efuse); i += 8) { |
| dev_info(&priv->udev->dev, "%02x: " |
| "%02x %02x %02x %02x %02x %02x %02x %02x\n", i, |
| raw[i], raw[i + 1], raw[i + 2], |
| raw[i + 3], raw[i + 4], raw[i + 5], |
| raw[i + 6], raw[i + 7]); |
| } |
| } |
| return 0; |
| } |
| |
| static int |
| rtl8xxxu_read_efuse8(struct rtl8xxxu_priv *priv, u16 offset, u8 *data) |
| { |
| int i; |
| u8 val8; |
| u32 val32; |
| |
| /* Write Address */ |
| rtl8xxxu_write8(priv, REG_EFUSE_CTRL + 1, offset & 0xff); |
| val8 = rtl8xxxu_read8(priv, REG_EFUSE_CTRL + 2); |
| val8 &= 0xfc; |
| val8 |= (offset >> 8) & 0x03; |
| rtl8xxxu_write8(priv, REG_EFUSE_CTRL + 2, val8); |
| |
| val8 = rtl8xxxu_read8(priv, REG_EFUSE_CTRL + 3); |
| rtl8xxxu_write8(priv, REG_EFUSE_CTRL + 3, val8 & 0x7f); |
| |
| /* Poll for data read */ |
| val32 = rtl8xxxu_read32(priv, REG_EFUSE_CTRL); |
| for (i = 0; i < RTL8XXXU_MAX_REG_POLL; i++) { |
| val32 = rtl8xxxu_read32(priv, REG_EFUSE_CTRL); |
| if (val32 & BIT(31)) |
| break; |
| } |
| |
| if (i == RTL8XXXU_MAX_REG_POLL) |
| return -EIO; |
| |
| udelay(50); |
| val32 = rtl8xxxu_read32(priv, REG_EFUSE_CTRL); |
| |
| *data = val32 & 0xff; |
| return 0; |
| } |
| |
| static int rtl8xxxu_read_efuse(struct rtl8xxxu_priv *priv) |
| { |
| struct device *dev = &priv->udev->dev; |
| int i, ret = 0; |
| u8 val8, word_mask, header, extheader; |
| u16 val16, efuse_addr, offset; |
| u32 val32; |
| |
| val16 = rtl8xxxu_read16(priv, REG_9346CR); |
| if (val16 & EEPROM_ENABLE) |
| priv->has_eeprom = 1; |
| if (val16 & EEPROM_BOOT) |
| priv->boot_eeprom = 1; |
| |
| if (priv->is_multi_func) { |
| val32 = rtl8xxxu_read32(priv, REG_EFUSE_TEST); |
| val32 = (val32 & ~EFUSE_SELECT_MASK) | EFUSE_WIFI_SELECT; |
| rtl8xxxu_write32(priv, REG_EFUSE_TEST, val32); |
| } |
| |
| dev_dbg(dev, "Booting from %s\n", |
| priv->boot_eeprom ? "EEPROM" : "EFUSE"); |
| |
| rtl8xxxu_write8(priv, REG_EFUSE_ACCESS, EFUSE_ACCESS_ENABLE); |
| |
| /* 1.2V Power: From VDDON with Power Cut(0x0000[15]), default valid */ |
| val16 = rtl8xxxu_read16(priv, REG_SYS_ISO_CTRL); |
| if (!(val16 & SYS_ISO_PWC_EV12V)) { |
| val16 |= SYS_ISO_PWC_EV12V; |
| rtl8xxxu_write16(priv, REG_SYS_ISO_CTRL, val16); |
| } |
| /* Reset: 0x0000[28], default valid */ |
| val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); |
| if (!(val16 & SYS_FUNC_ELDR)) { |
| val16 |= SYS_FUNC_ELDR; |
| rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); |
| } |
| |
| /* |
| * Clock: Gated(0x0008[5]) 8M(0x0008[1]) clock from ANA, default valid |
| */ |
| val16 = rtl8xxxu_read16(priv, REG_SYS_CLKR); |
| if (!(val16 & SYS_CLK_LOADER_ENABLE) || !(val16 & SYS_CLK_ANA8M)) { |
| val16 |= (SYS_CLK_LOADER_ENABLE | SYS_CLK_ANA8M); |
| rtl8xxxu_write16(priv, REG_SYS_CLKR, val16); |
| } |
| |
| /* Default value is 0xff */ |
| memset(priv->efuse_wifi.raw, 0xff, EFUSE_MAP_LEN); |
| |
| efuse_addr = 0; |
| while (efuse_addr < EFUSE_REAL_CONTENT_LEN_8723A) { |
| u16 map_addr; |
| |
| ret = rtl8xxxu_read_efuse8(priv, efuse_addr++, &header); |
| if (ret || header == 0xff) |
| goto exit; |
| |
| if ((header & 0x1f) == 0x0f) { /* extended header */ |
| offset = (header & 0xe0) >> 5; |
| |
| ret = rtl8xxxu_read_efuse8(priv, efuse_addr++, |
| &extheader); |
| if (ret) |
| goto exit; |
| /* All words disabled */ |
| if ((extheader & 0x0f) == 0x0f) |
| continue; |
| |
| offset |= ((extheader & 0xf0) >> 1); |
| word_mask = extheader & 0x0f; |
| } else { |
| offset = (header >> 4) & 0x0f; |
| word_mask = header & 0x0f; |
| } |
| |
| /* Get word enable value from PG header */ |
| |
| /* We have 8 bits to indicate validity */ |
| map_addr = offset * 8; |
| if (map_addr >= EFUSE_MAP_LEN) { |
| dev_warn(dev, "%s: Illegal map_addr (%04x), " |
| "efuse corrupt!\n", |
| __func__, map_addr); |
| ret = -EINVAL; |
| goto exit; |
| } |
| for (i = 0; i < EFUSE_MAX_WORD_UNIT; i++) { |
| /* Check word enable condition in the section */ |
| if (word_mask & BIT(i)) { |
| map_addr += 2; |
| continue; |
| } |
| |
| ret = rtl8xxxu_read_efuse8(priv, efuse_addr++, &val8); |
| if (ret) |
| goto exit; |
| priv->efuse_wifi.raw[map_addr++] = val8; |
| |
| ret = rtl8xxxu_read_efuse8(priv, efuse_addr++, &val8); |
| if (ret) |
| goto exit; |
| priv->efuse_wifi.raw[map_addr++] = val8; |
| } |
| } |
| |
| exit: |
| rtl8xxxu_write8(priv, REG_EFUSE_ACCESS, EFUSE_ACCESS_DISABLE); |
| |
| return ret; |
| } |
| |
| static void rtl8xxxu_reset_8051(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| u16 sys_func; |
| |
| val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1); |
| val8 &= ~BIT(0); |
| rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8); |
| sys_func = rtl8xxxu_read16(priv, REG_SYS_FUNC); |
| sys_func &= ~SYS_FUNC_CPU_ENABLE; |
| rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func); |
| val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1); |
| val8 |= BIT(0); |
| rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8); |
| sys_func |= SYS_FUNC_CPU_ENABLE; |
| rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func); |
| } |
| |
| static int rtl8xxxu_start_firmware(struct rtl8xxxu_priv *priv) |
| { |
| struct device *dev = &priv->udev->dev; |
| int ret = 0, i; |
| u32 val32; |
| |
| /* Poll checksum report */ |
| for (i = 0; i < RTL8XXXU_FIRMWARE_POLL_MAX; i++) { |
| val32 = rtl8xxxu_read32(priv, REG_MCU_FW_DL); |
| if (val32 & MCU_FW_DL_CSUM_REPORT) |
| break; |
| } |
| |
| if (i == RTL8XXXU_FIRMWARE_POLL_MAX) { |
| dev_warn(dev, "Firmware checksum poll timed out\n"); |
| ret = -EAGAIN; |
| goto exit; |
| } |
| |
| val32 = rtl8xxxu_read32(priv, REG_MCU_FW_DL); |
| val32 |= MCU_FW_DL_READY; |
| val32 &= ~MCU_WINT_INIT_READY; |
| rtl8xxxu_write32(priv, REG_MCU_FW_DL, val32); |
| |
| /* |
| * Reset the 8051 in order for the firmware to start running, |
| * otherwise it won't come up on the 8192eu |
| */ |
| rtl8xxxu_reset_8051(priv); |
| |
| /* Wait for firmware to become ready */ |
| for (i = 0; i < RTL8XXXU_FIRMWARE_POLL_MAX; i++) { |
| val32 = rtl8xxxu_read32(priv, REG_MCU_FW_DL); |
| if (val32 & MCU_WINT_INIT_READY) |
| break; |
| |
| udelay(100); |
| } |
| |
| if (i == RTL8XXXU_FIRMWARE_POLL_MAX) { |
| dev_warn(dev, "Firmware failed to start\n"); |
| ret = -EAGAIN; |
| goto exit; |
| } |
| |
| /* |
| * Init H2C command |
| */ |
| if (priv->rtlchip == 0x8723b) |
| rtl8xxxu_write8(priv, REG_HMTFR, 0x0f); |
| exit: |
| return ret; |
| } |
| |
| static int rtl8xxxu_download_firmware(struct rtl8xxxu_priv *priv) |
| { |
| int pages, remainder, i, ret; |
| u8 val8; |
| u16 val16; |
| u32 val32; |
| u8 *fwptr; |
| |
| val8 = rtl8xxxu_read8(priv, REG_SYS_FUNC + 1); |
| val8 |= 4; |
| rtl8xxxu_write8(priv, REG_SYS_FUNC + 1, val8); |
| |
| /* 8051 enable */ |
| val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); |
| val16 |= SYS_FUNC_CPU_ENABLE; |
| rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); |
| |
| val8 = rtl8xxxu_read8(priv, REG_MCU_FW_DL); |
| if (val8 & MCU_FW_RAM_SEL) { |
| pr_info("do the RAM reset\n"); |
| rtl8xxxu_write8(priv, REG_MCU_FW_DL, 0x00); |
| rtl8xxxu_reset_8051(priv); |
| } |
| |
| /* MCU firmware download enable */ |
| val8 = rtl8xxxu_read8(priv, REG_MCU_FW_DL); |
| val8 |= MCU_FW_DL_ENABLE; |
| rtl8xxxu_write8(priv, REG_MCU_FW_DL, val8); |
| |
| /* 8051 reset */ |
| val32 = rtl8xxxu_read32(priv, REG_MCU_FW_DL); |
| val32 &= ~BIT(19); |
| rtl8xxxu_write32(priv, REG_MCU_FW_DL, val32); |
| |
| /* Reset firmware download checksum */ |
| val8 = rtl8xxxu_read8(priv, REG_MCU_FW_DL); |
| val8 |= MCU_FW_DL_CSUM_REPORT; |
| rtl8xxxu_write8(priv, REG_MCU_FW_DL, val8); |
| |
| pages = priv->fw_size / RTL_FW_PAGE_SIZE; |
| remainder = priv->fw_size % RTL_FW_PAGE_SIZE; |
| |
| fwptr = priv->fw_data->data; |
| |
| for (i = 0; i < pages; i++) { |
| val8 = rtl8xxxu_read8(priv, REG_MCU_FW_DL + 2) & 0xF8; |
| val8 |= i; |
| rtl8xxxu_write8(priv, REG_MCU_FW_DL + 2, val8); |
| |
| ret = rtl8xxxu_writeN(priv, REG_FW_START_ADDRESS, |
| fwptr, RTL_FW_PAGE_SIZE); |
| if (ret != RTL_FW_PAGE_SIZE) { |
| ret = -EAGAIN; |
| goto fw_abort; |
| } |
| |
| fwptr += RTL_FW_PAGE_SIZE; |
| } |
| |
| if (remainder) { |
| val8 = rtl8xxxu_read8(priv, REG_MCU_FW_DL + 2) & 0xF8; |
| val8 |= i; |
| rtl8xxxu_write8(priv, REG_MCU_FW_DL + 2, val8); |
| ret = rtl8xxxu_writeN(priv, REG_FW_START_ADDRESS, |
| fwptr, remainder); |
| if (ret != remainder) { |
| ret = -EAGAIN; |
| goto fw_abort; |
| } |
| } |
| |
| ret = 0; |
| fw_abort: |
| /* MCU firmware download disable */ |
| val16 = rtl8xxxu_read16(priv, REG_MCU_FW_DL); |
| val16 &= ~MCU_FW_DL_ENABLE; |
| rtl8xxxu_write16(priv, REG_MCU_FW_DL, val16); |
| |
| return ret; |
| } |
| |
| static int rtl8xxxu_load_firmware(struct rtl8xxxu_priv *priv, char *fw_name) |
| { |
| struct device *dev = &priv->udev->dev; |
| const struct firmware *fw; |
| int ret = 0; |
| u16 signature; |
| |
| dev_info(dev, "%s: Loading firmware %s\n", DRIVER_NAME, fw_name); |
| if (request_firmware(&fw, fw_name, &priv->udev->dev)) { |
| dev_warn(dev, "request_firmware(%s) failed\n", fw_name); |
| ret = -EAGAIN; |
| goto exit; |
| } |
| if (!fw) { |
| dev_warn(dev, "Firmware data not available\n"); |
| ret = -EINVAL; |
| goto exit; |
| } |
| |
| priv->fw_data = kmemdup(fw->data, fw->size, GFP_KERNEL); |
| if (!priv->fw_data) { |
| ret = -ENOMEM; |
| goto exit; |
| } |
| priv->fw_size = fw->size - sizeof(struct rtl8xxxu_firmware_header); |
| |
| signature = le16_to_cpu(priv->fw_data->signature); |
| switch (signature & 0xfff0) { |
| case 0x92e0: |
| case 0x92c0: |
| case 0x88c0: |
| case 0x5300: |
| case 0x2300: |
| break; |
| default: |
| ret = -EINVAL; |
| dev_warn(dev, "%s: Invalid firmware signature: 0x%04x\n", |
| __func__, signature); |
| } |
| |
| dev_info(dev, "Firmware revision %i.%i (signature 0x%04x)\n", |
| le16_to_cpu(priv->fw_data->major_version), |
| priv->fw_data->minor_version, signature); |
| |
| exit: |
| release_firmware(fw); |
| return ret; |
| } |
| |
| static int rtl8723au_load_firmware(struct rtl8xxxu_priv *priv) |
| { |
| char *fw_name; |
| int ret; |
| |
| switch (priv->chip_cut) { |
| case 0: |
| fw_name = "rtlwifi/rtl8723aufw_A.bin"; |
| break; |
| case 1: |
| if (priv->enable_bluetooth) |
| fw_name = "rtlwifi/rtl8723aufw_B.bin"; |
| else |
| fw_name = "rtlwifi/rtl8723aufw_B_NoBT.bin"; |
| |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| ret = rtl8xxxu_load_firmware(priv, fw_name); |
| return ret; |
| } |
| |
| static int rtl8723bu_load_firmware(struct rtl8xxxu_priv *priv) |
| { |
| char *fw_name; |
| int ret; |
| |
| if (priv->enable_bluetooth) |
| fw_name = "rtlwifi/rtl8723bu_bt.bin"; |
| else |
| fw_name = "rtlwifi/rtl8723bu_nic.bin"; |
| |
| ret = rtl8xxxu_load_firmware(priv, fw_name); |
| return ret; |
| } |
| |
| #ifdef CONFIG_RTL8XXXU_UNTESTED |
| |
| static int rtl8192cu_load_firmware(struct rtl8xxxu_priv *priv) |
| { |
| char *fw_name; |
| int ret; |
| |
| if (!priv->vendor_umc) |
| fw_name = "rtlwifi/rtl8192cufw_TMSC.bin"; |
| else if (priv->chip_cut || priv->rtlchip == 0x8192c) |
| fw_name = "rtlwifi/rtl8192cufw_B.bin"; |
| else |
| fw_name = "rtlwifi/rtl8192cufw_A.bin"; |
| |
| ret = rtl8xxxu_load_firmware(priv, fw_name); |
| |
| return ret; |
| } |
| |
| #endif |
| |
| static int rtl8192eu_load_firmware(struct rtl8xxxu_priv *priv) |
| { |
| char *fw_name; |
| int ret; |
| |
| fw_name = "rtlwifi/rtl8192eu_nic.bin"; |
| |
| ret = rtl8xxxu_load_firmware(priv, fw_name); |
| |
| return ret; |
| } |
| |
| static void rtl8xxxu_firmware_self_reset(struct rtl8xxxu_priv *priv) |
| { |
| u16 val16; |
| int i = 100; |
| |
| /* Inform 8051 to perform reset */ |
| rtl8xxxu_write8(priv, REG_HMTFR + 3, 0x20); |
| |
| for (i = 100; i > 0; i--) { |
| val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); |
| |
| if (!(val16 & SYS_FUNC_CPU_ENABLE)) { |
| dev_dbg(&priv->udev->dev, |
| "%s: Firmware self reset success!\n", __func__); |
| break; |
| } |
| udelay(50); |
| } |
| |
| if (!i) { |
| /* Force firmware reset */ |
| val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); |
| val16 &= ~SYS_FUNC_CPU_ENABLE; |
| rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); |
| } |
| } |
| |
| static void rtl8723bu_phy_init_antenna_selection(struct rtl8xxxu_priv *priv) |
| { |
| u32 val32; |
| |
| val32 = rtl8xxxu_read32(priv, 0x64); |
| val32 &= ~(BIT(20) | BIT(24)); |
| rtl8xxxu_write32(priv, 0x64, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG); |
| val32 &= ~BIT(4); |
| rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG); |
| val32 |= BIT(3); |
| rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); |
| val32 |= BIT(24); |
| rtl8xxxu_write32(priv, REG_LEDCFG0, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); |
| val32 &= ~BIT(23); |
| rtl8xxxu_write32(priv, REG_LEDCFG0, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER); |
| val32 |= (BIT(0) | BIT(1)); |
| rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_RFE_CTRL_ANTA_SRC); |
| val32 &= 0xffffff00; |
| val32 |= 0x77; |
| rtl8xxxu_write32(priv, REG_RFE_CTRL_ANTA_SRC, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_PWR_DATA); |
| val32 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN; |
| rtl8xxxu_write32(priv, REG_PWR_DATA, val32); |
| } |
| |
| static int |
| rtl8xxxu_init_mac(struct rtl8xxxu_priv *priv, struct rtl8xxxu_reg8val *array) |
| { |
| int i, ret; |
| u16 reg; |
| u8 val; |
| |
| for (i = 0; ; i++) { |
| reg = array[i].reg; |
| val = array[i].val; |
| |
| if (reg == 0xffff && val == 0xff) |
| break; |
| |
| ret = rtl8xxxu_write8(priv, reg, val); |
| if (ret != 1) { |
| dev_warn(&priv->udev->dev, |
| "Failed to initialize MAC\n"); |
| return -EAGAIN; |
| } |
| } |
| |
| if (priv->rtlchip != 0x8723b) |
| rtl8xxxu_write8(priv, REG_MAX_AGGR_NUM, 0x0a); |
| |
| return 0; |
| } |
| |
| static int rtl8xxxu_init_phy_regs(struct rtl8xxxu_priv *priv, |
| struct rtl8xxxu_reg32val *array) |
| { |
| int i, ret; |
| u16 reg; |
| u32 val; |
| |
| for (i = 0; ; i++) { |
| reg = array[i].reg; |
| val = array[i].val; |
| |
| if (reg == 0xffff && val == 0xffffffff) |
| break; |
| |
| ret = rtl8xxxu_write32(priv, reg, val); |
| if (ret != sizeof(val)) { |
| dev_warn(&priv->udev->dev, |
| "Failed to initialize PHY\n"); |
| return -EAGAIN; |
| } |
| udelay(1); |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * Most of this is black magic retrieved from the old rtl8723au driver |
| */ |
| static int rtl8xxxu_init_phy_bb(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8, ldoa15, ldov12d, lpldo, ldohci12; |
| u16 val16; |
| u32 val32; |
| |
| /* |
| * Todo: The vendor driver maintains a table of PHY register |
| * addresses, which is initialized here. Do we need this? |
| */ |
| |
| if (priv->rtlchip == 0x8723b) { |
| val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); |
| val16 |= SYS_FUNC_BB_GLB_RSTN | SYS_FUNC_BBRSTB | |
| SYS_FUNC_DIO_RF; |
| rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); |
| |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00); |
| } else { |
| val8 = rtl8xxxu_read8(priv, REG_AFE_PLL_CTRL); |
| udelay(2); |
| val8 |= AFE_PLL_320_ENABLE; |
| rtl8xxxu_write8(priv, REG_AFE_PLL_CTRL, val8); |
| udelay(2); |
| |
| rtl8xxxu_write8(priv, REG_AFE_PLL_CTRL + 1, 0xff); |
| udelay(2); |
| |
| val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); |
| val16 |= SYS_FUNC_BB_GLB_RSTN | SYS_FUNC_BBRSTB; |
| rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); |
| } |
| |
| if (priv->rtlchip != 0x8723b) { |
| /* AFE_XTAL_RF_GATE (bit 14) if addressing as 32 bit register */ |
| val32 = rtl8xxxu_read32(priv, REG_AFE_XTAL_CTRL); |
| val32 &= ~AFE_XTAL_RF_GATE; |
| if (priv->has_bluetooth) |
| val32 &= ~AFE_XTAL_BT_GATE; |
| rtl8xxxu_write32(priv, REG_AFE_XTAL_CTRL, val32); |
| } |
| |
| /* 6. 0x1f[7:0] = 0x07 */ |
| val8 = RF_ENABLE | RF_RSTB | RF_SDMRSTB; |
| rtl8xxxu_write8(priv, REG_RF_CTRL, val8); |
| |
| if (priv->hi_pa) |
| rtl8xxxu_init_phy_regs(priv, rtl8188ru_phy_1t_highpa_table); |
| else if (priv->tx_paths == 2) |
| rtl8xxxu_init_phy_regs(priv, rtl8192cu_phy_2t_init_table); |
| else if (priv->rtlchip == 0x8723b) { |
| /* |
| * Why? |
| */ |
| rtl8xxxu_write8(priv, REG_SYS_FUNC, 0xe3); |
| rtl8xxxu_write8(priv, REG_AFE_XTAL_CTRL + 1, 0x80); |
| rtl8xxxu_init_phy_regs(priv, rtl8723b_phy_1t_init_table); |
| } else |
| rtl8xxxu_init_phy_regs(priv, rtl8723a_phy_1t_init_table); |
| |
| |
| if (priv->rtlchip == 0x8188c && priv->hi_pa && |
| priv->vendor_umc && priv->chip_cut == 1) |
| rtl8xxxu_write8(priv, REG_OFDM0_AGC_PARM1 + 2, 0x50); |
| |
| if (priv->tx_paths == 1 && priv->rx_paths == 2) { |
| /* |
| * For 1T2R boards, patch the registers. |
| * |
| * It looks like 8191/2 1T2R boards use path B for TX |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_TX_INFO); |
| val32 &= ~(BIT(0) | BIT(1)); |
| val32 |= BIT(1); |
| rtl8xxxu_write32(priv, REG_FPGA0_TX_INFO, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA1_TX_INFO); |
| val32 &= ~0x300033; |
| val32 |= 0x200022; |
| rtl8xxxu_write32(priv, REG_FPGA1_TX_INFO, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_CCK0_AFE_SETTING); |
| val32 &= 0xff000000; |
| val32 |= 0x45000000; |
| rtl8xxxu_write32(priv, REG_CCK0_AFE_SETTING, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_TRX_PATH_ENABLE); |
| val32 &= ~(OFDM_RF_PATH_RX_MASK | OFDM_RF_PATH_TX_MASK); |
| val32 |= (OFDM_RF_PATH_RX_A | OFDM_RF_PATH_RX_B | |
| OFDM_RF_PATH_TX_B); |
| rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_AGC_PARM1); |
| val32 &= ~(BIT(4) | BIT(5)); |
| val32 |= BIT(4); |
| rtl8xxxu_write32(priv, REG_OFDM0_AGC_PARM1, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_TX_CCK_RFON); |
| val32 &= ~(BIT(27) | BIT(26)); |
| val32 |= BIT(27); |
| rtl8xxxu_write32(priv, REG_TX_CCK_RFON, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_TX_CCK_BBON); |
| val32 &= ~(BIT(27) | BIT(26)); |
| val32 |= BIT(27); |
| rtl8xxxu_write32(priv, REG_TX_CCK_BBON, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_TX_OFDM_RFON); |
| val32 &= ~(BIT(27) | BIT(26)); |
| val32 |= BIT(27); |
| rtl8xxxu_write32(priv, REG_TX_OFDM_RFON, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_TX_OFDM_BBON); |
| val32 &= ~(BIT(27) | BIT(26)); |
| val32 |= BIT(27); |
| rtl8xxxu_write32(priv, REG_TX_OFDM_BBON, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_TX_TO_TX); |
| val32 &= ~(BIT(27) | BIT(26)); |
| val32 |= BIT(27); |
| rtl8xxxu_write32(priv, REG_TX_TO_TX, val32); |
| } |
| |
| if (priv->rtlchip == 0x8723b) |
| rtl8xxxu_init_phy_regs(priv, rtl8xxx_agc_8723bu_table); |
| else if (priv->hi_pa) |
| rtl8xxxu_init_phy_regs(priv, rtl8xxx_agc_highpa_table); |
| else |
| rtl8xxxu_init_phy_regs(priv, rtl8xxx_agc_standard_table); |
| |
| if (priv->has_xtalk) { |
| val32 = rtl8xxxu_read32(priv, REG_MAC_PHY_CTRL); |
| |
| val8 = priv->xtalk; |
| val32 &= 0xff000fff; |
| val32 |= ((val8 | (val8 << 6)) << 12); |
| |
| rtl8xxxu_write32(priv, REG_MAC_PHY_CTRL, val32); |
| } |
| |
| if (priv->rtlchip != 0x8723bu) { |
| ldoa15 = LDOA15_ENABLE | LDOA15_OBUF; |
| ldov12d = LDOV12D_ENABLE | BIT(2) | (2 << LDOV12D_VADJ_SHIFT); |
| ldohci12 = 0x57; |
| lpldo = 1; |
| val32 = (lpldo << 24) | (ldohci12 << 16) | |
| (ldov12d << 8) | ldoa15; |
| |
| rtl8xxxu_write32(priv, REG_LDOA15_CTRL, val32); |
| } |
| |
| return 0; |
| } |
| |
| static int rtl8xxxu_init_rf_regs(struct rtl8xxxu_priv *priv, |
| struct rtl8xxxu_rfregval *array, |
| enum rtl8xxxu_rfpath path) |
| { |
| int i, ret; |
| u8 reg; |
| u32 val; |
| |
| for (i = 0; ; i++) { |
| reg = array[i].reg; |
| val = array[i].val; |
| |
| if (reg == 0xff && val == 0xffffffff) |
| break; |
| |
| switch (reg) { |
| case 0xfe: |
| msleep(50); |
| continue; |
| case 0xfd: |
| mdelay(5); |
| continue; |
| case 0xfc: |
| mdelay(1); |
| continue; |
| case 0xfb: |
| udelay(50); |
| continue; |
| case 0xfa: |
| udelay(5); |
| continue; |
| case 0xf9: |
| udelay(1); |
| continue; |
| } |
| |
| ret = rtl8xxxu_write_rfreg(priv, path, reg, val); |
| if (ret) { |
| dev_warn(&priv->udev->dev, |
| "Failed to initialize RF\n"); |
| return -EAGAIN; |
| } |
| udelay(1); |
| } |
| |
| return 0; |
| } |
| |
| static int rtl8xxxu_init_phy_rf(struct rtl8xxxu_priv *priv, |
| struct rtl8xxxu_rfregval *table, |
| enum rtl8xxxu_rfpath path) |
| { |
| u32 val32; |
| u16 val16, rfsi_rfenv; |
| u16 reg_sw_ctrl, reg_int_oe, reg_hssi_parm2; |
| |
| switch (path) { |
| case RF_A: |
| reg_sw_ctrl = REG_FPGA0_XA_RF_SW_CTRL; |
| reg_int_oe = REG_FPGA0_XA_RF_INT_OE; |
| reg_hssi_parm2 = REG_FPGA0_XA_HSSI_PARM2; |
| break; |
| case RF_B: |
| reg_sw_ctrl = REG_FPGA0_XB_RF_SW_CTRL; |
| reg_int_oe = REG_FPGA0_XB_RF_INT_OE; |
| reg_hssi_parm2 = REG_FPGA0_XB_HSSI_PARM2; |
| break; |
| default: |
| dev_err(&priv->udev->dev, "%s:Unsupported RF path %c\n", |
| __func__, path + 'A'); |
| return -EINVAL; |
| } |
| /* For path B, use XB */ |
| rfsi_rfenv = rtl8xxxu_read16(priv, reg_sw_ctrl); |
| rfsi_rfenv &= FPGA0_RF_RFENV; |
| |
| /* |
| * These two we might be able to optimize into one |
| */ |
| val32 = rtl8xxxu_read32(priv, reg_int_oe); |
| val32 |= BIT(20); /* 0x10 << 16 */ |
| rtl8xxxu_write32(priv, reg_int_oe, val32); |
| udelay(1); |
| |
| val32 = rtl8xxxu_read32(priv, reg_int_oe); |
| val32 |= BIT(4); |
| rtl8xxxu_write32(priv, reg_int_oe, val32); |
| udelay(1); |
| |
| /* |
| * These two we might be able to optimize into one |
| */ |
| val32 = rtl8xxxu_read32(priv, reg_hssi_parm2); |
| val32 &= ~FPGA0_HSSI_3WIRE_ADDR_LEN; |
| rtl8xxxu_write32(priv, reg_hssi_parm2, val32); |
| udelay(1); |
| |
| val32 = rtl8xxxu_read32(priv, reg_hssi_parm2); |
| val32 &= ~FPGA0_HSSI_3WIRE_DATA_LEN; |
| rtl8xxxu_write32(priv, reg_hssi_parm2, val32); |
| udelay(1); |
| |
| rtl8xxxu_init_rf_regs(priv, table, path); |
| |
| /* For path B, use XB */ |
| val16 = rtl8xxxu_read16(priv, reg_sw_ctrl); |
| val16 &= ~FPGA0_RF_RFENV; |
| val16 |= rfsi_rfenv; |
| rtl8xxxu_write16(priv, reg_sw_ctrl, val16); |
| |
| return 0; |
| } |
| |
| static int rtl8xxxu_llt_write(struct rtl8xxxu_priv *priv, u8 address, u8 data) |
| { |
| int ret = -EBUSY; |
| int count = 0; |
| u32 value; |
| |
| value = LLT_OP_WRITE | address << 8 | data; |
| |
| rtl8xxxu_write32(priv, REG_LLT_INIT, value); |
| |
| do { |
| value = rtl8xxxu_read32(priv, REG_LLT_INIT); |
| if ((value & LLT_OP_MASK) == LLT_OP_INACTIVE) { |
| ret = 0; |
| break; |
| } |
| } while (count++ < 20); |
| |
| return ret; |
| } |
| |
| static int rtl8xxxu_init_llt_table(struct rtl8xxxu_priv *priv, u8 last_tx_page) |
| { |
| int ret; |
| int i; |
| |
| for (i = 0; i < last_tx_page; i++) { |
| ret = rtl8xxxu_llt_write(priv, i, i + 1); |
| if (ret) |
| goto exit; |
| } |
| |
| ret = rtl8xxxu_llt_write(priv, last_tx_page, 0xff); |
| if (ret) |
| goto exit; |
| |
| /* Mark remaining pages as a ring buffer */ |
| for (i = last_tx_page + 1; i < 0xff; i++) { |
| ret = rtl8xxxu_llt_write(priv, i, (i + 1)); |
| if (ret) |
| goto exit; |
| } |
| |
| /* Let last entry point to the start entry of ring buffer */ |
| ret = rtl8xxxu_llt_write(priv, 0xff, last_tx_page + 1); |
| if (ret) |
| goto exit; |
| |
| exit: |
| return ret; |
| } |
| |
| static int rtl8xxxu_auto_llt_table(struct rtl8xxxu_priv *priv, u8 last_tx_page) |
| { |
| u32 val32; |
| int ret = 0; |
| int i; |
| |
| val32 = rtl8xxxu_read32(priv, REG_AUTO_LLT); |
| val32 |= AUTO_LLT_INIT_LLT; |
| rtl8xxxu_write32(priv, REG_AUTO_LLT, val32); |
| |
| for (i = 500; i; i--) { |
| val32 = rtl8xxxu_read32(priv, REG_AUTO_LLT); |
| if (!(val32 & AUTO_LLT_INIT_LLT)) |
| break; |
| usleep_range(2, 4); |
| } |
| |
| if (!i) { |
| ret = -EBUSY; |
| dev_warn(&priv->udev->dev, "LLT table init failed\n"); |
| } |
| |
| return ret; |
| } |
| |
| static int rtl8xxxu_init_queue_priority(struct rtl8xxxu_priv *priv) |
| { |
| u16 val16, hi, lo; |
| u16 hiq, mgq, bkq, beq, viq, voq; |
| int hip, mgp, bkp, bep, vip, vop; |
| int ret = 0; |
| |
| switch (priv->ep_tx_count) { |
| case 1: |
| if (priv->ep_tx_high_queue) { |
| hi = TRXDMA_QUEUE_HIGH; |
| } else if (priv->ep_tx_low_queue) { |
| hi = TRXDMA_QUEUE_LOW; |
| } else if (priv->ep_tx_normal_queue) { |
| hi = TRXDMA_QUEUE_NORMAL; |
| } else { |
| hi = 0; |
| ret = -EINVAL; |
| } |
| |
| hiq = hi; |
| mgq = hi; |
| bkq = hi; |
| beq = hi; |
| viq = hi; |
| voq = hi; |
| |
| hip = 0; |
| mgp = 0; |
| bkp = 0; |
| bep = 0; |
| vip = 0; |
| vop = 0; |
| break; |
| case 2: |
| if (priv->ep_tx_high_queue && priv->ep_tx_low_queue) { |
| hi = TRXDMA_QUEUE_HIGH; |
| lo = TRXDMA_QUEUE_LOW; |
| } else if (priv->ep_tx_normal_queue && priv->ep_tx_low_queue) { |
| hi = TRXDMA_QUEUE_NORMAL; |
| lo = TRXDMA_QUEUE_LOW; |
| } else if (priv->ep_tx_high_queue && priv->ep_tx_normal_queue) { |
| hi = TRXDMA_QUEUE_HIGH; |
| lo = TRXDMA_QUEUE_NORMAL; |
| } else { |
| ret = -EINVAL; |
| hi = 0; |
| lo = 0; |
| } |
| |
| hiq = hi; |
| mgq = hi; |
| bkq = lo; |
| beq = lo; |
| viq = hi; |
| voq = hi; |
| |
| hip = 0; |
| mgp = 0; |
| bkp = 1; |
| bep = 1; |
| vip = 0; |
| vop = 0; |
| break; |
| case 3: |
| beq = TRXDMA_QUEUE_LOW; |
| bkq = TRXDMA_QUEUE_LOW; |
| viq = TRXDMA_QUEUE_NORMAL; |
| voq = TRXDMA_QUEUE_HIGH; |
| mgq = TRXDMA_QUEUE_HIGH; |
| hiq = TRXDMA_QUEUE_HIGH; |
| |
| hip = hiq ^ 3; |
| mgp = mgq ^ 3; |
| bkp = bkq ^ 3; |
| bep = beq ^ 3; |
| vip = viq ^ 3; |
| vop = viq ^ 3; |
| break; |
| default: |
| ret = -EINVAL; |
| } |
| |
| /* |
| * None of the vendor drivers are configuring the beacon |
| * queue here .... why? |
| */ |
| if (!ret) { |
| val16 = rtl8xxxu_read16(priv, REG_TRXDMA_CTRL); |
| val16 &= 0x7; |
| val16 |= (voq << TRXDMA_CTRL_VOQ_SHIFT) | |
| (viq << TRXDMA_CTRL_VIQ_SHIFT) | |
| (beq << TRXDMA_CTRL_BEQ_SHIFT) | |
| (bkq << TRXDMA_CTRL_BKQ_SHIFT) | |
| (mgq << TRXDMA_CTRL_MGQ_SHIFT) | |
| (hiq << TRXDMA_CTRL_HIQ_SHIFT); |
| rtl8xxxu_write16(priv, REG_TRXDMA_CTRL, val16); |
| |
| priv->pipe_out[TXDESC_QUEUE_VO] = |
| usb_sndbulkpipe(priv->udev, priv->out_ep[vop]); |
| priv->pipe_out[TXDESC_QUEUE_VI] = |
| usb_sndbulkpipe(priv->udev, priv->out_ep[vip]); |
| priv->pipe_out[TXDESC_QUEUE_BE] = |
| usb_sndbulkpipe(priv->udev, priv->out_ep[bep]); |
| priv->pipe_out[TXDESC_QUEUE_BK] = |
| usb_sndbulkpipe(priv->udev, priv->out_ep[bkp]); |
| priv->pipe_out[TXDESC_QUEUE_BEACON] = |
| usb_sndbulkpipe(priv->udev, priv->out_ep[0]); |
| priv->pipe_out[TXDESC_QUEUE_MGNT] = |
| usb_sndbulkpipe(priv->udev, priv->out_ep[mgp]); |
| priv->pipe_out[TXDESC_QUEUE_HIGH] = |
| usb_sndbulkpipe(priv->udev, priv->out_ep[hip]); |
| priv->pipe_out[TXDESC_QUEUE_CMD] = |
| usb_sndbulkpipe(priv->udev, priv->out_ep[0]); |
| } |
| |
| return ret; |
| } |
| |
| static void rtl8xxxu_fill_iqk_matrix_a(struct rtl8xxxu_priv *priv, |
| bool iqk_ok, int result[][8], |
| int candidate, bool tx_only) |
| { |
| u32 oldval, x, tx0_a, reg; |
| int y, tx0_c; |
| u32 val32; |
| |
| if (!iqk_ok) |
| return; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_TX_IQ_IMBALANCE); |
| oldval = val32 >> 22; |
| |
| x = result[candidate][0]; |
| if ((x & 0x00000200) != 0) |
| x = x | 0xfffffc00; |
| tx0_a = (x * oldval) >> 8; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_TX_IQ_IMBALANCE); |
| val32 &= ~0x3ff; |
| val32 |= tx0_a; |
| rtl8xxxu_write32(priv, REG_OFDM0_XA_TX_IQ_IMBALANCE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_ENERGY_CCA_THRES); |
| val32 &= ~BIT(31); |
| if ((x * oldval >> 7) & 0x1) |
| val32 |= BIT(31); |
| rtl8xxxu_write32(priv, REG_OFDM0_ENERGY_CCA_THRES, val32); |
| |
| y = result[candidate][1]; |
| if ((y & 0x00000200) != 0) |
| y = y | 0xfffffc00; |
| tx0_c = (y * oldval) >> 8; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XC_TX_AFE); |
| val32 &= ~0xf0000000; |
| val32 |= (((tx0_c & 0x3c0) >> 6) << 28); |
| rtl8xxxu_write32(priv, REG_OFDM0_XC_TX_AFE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_TX_IQ_IMBALANCE); |
| val32 &= ~0x003f0000; |
| val32 |= ((tx0_c & 0x3f) << 16); |
| rtl8xxxu_write32(priv, REG_OFDM0_XA_TX_IQ_IMBALANCE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_ENERGY_CCA_THRES); |
| val32 &= ~BIT(29); |
| if ((y * oldval >> 7) & 0x1) |
| val32 |= BIT(29); |
| rtl8xxxu_write32(priv, REG_OFDM0_ENERGY_CCA_THRES, val32); |
| |
| if (tx_only) { |
| dev_dbg(&priv->udev->dev, "%s: only TX\n", __func__); |
| return; |
| } |
| |
| reg = result[candidate][2]; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_RX_IQ_IMBALANCE); |
| val32 &= ~0x3ff; |
| val32 |= (reg & 0x3ff); |
| rtl8xxxu_write32(priv, REG_OFDM0_XA_RX_IQ_IMBALANCE, val32); |
| |
| reg = result[candidate][3] & 0x3F; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_RX_IQ_IMBALANCE); |
| val32 &= ~0xfc00; |
| val32 |= ((reg << 10) & 0xfc00); |
| rtl8xxxu_write32(priv, REG_OFDM0_XA_RX_IQ_IMBALANCE, val32); |
| |
| reg = (result[candidate][3] >> 6) & 0xF; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_RX_IQ_EXT_ANTA); |
| val32 &= ~0xf0000000; |
| val32 |= (reg << 28); |
| rtl8xxxu_write32(priv, REG_OFDM0_RX_IQ_EXT_ANTA, val32); |
| } |
| |
| static void rtl8xxxu_fill_iqk_matrix_b(struct rtl8xxxu_priv *priv, |
| bool iqk_ok, int result[][8], |
| int candidate, bool tx_only) |
| { |
| u32 oldval, x, tx1_a, reg; |
| int y, tx1_c; |
| u32 val32; |
| |
| if (!iqk_ok) |
| return; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_TX_IQ_IMBALANCE); |
| oldval = val32 >> 22; |
| |
| x = result[candidate][4]; |
| if ((x & 0x00000200) != 0) |
| x = x | 0xfffffc00; |
| tx1_a = (x * oldval) >> 8; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_TX_IQ_IMBALANCE); |
| val32 &= ~0x3ff; |
| val32 |= tx1_a; |
| rtl8xxxu_write32(priv, REG_OFDM0_XB_TX_IQ_IMBALANCE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_ENERGY_CCA_THRES); |
| val32 &= ~BIT(27); |
| if ((x * oldval >> 7) & 0x1) |
| val32 |= BIT(27); |
| rtl8xxxu_write32(priv, REG_OFDM0_ENERGY_CCA_THRES, val32); |
| |
| y = result[candidate][5]; |
| if ((y & 0x00000200) != 0) |
| y = y | 0xfffffc00; |
| tx1_c = (y * oldval) >> 8; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XD_TX_AFE); |
| val32 &= ~0xf0000000; |
| val32 |= (((tx1_c & 0x3c0) >> 6) << 28); |
| rtl8xxxu_write32(priv, REG_OFDM0_XD_TX_AFE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_TX_IQ_IMBALANCE); |
| val32 &= ~0x003f0000; |
| val32 |= ((tx1_c & 0x3f) << 16); |
| rtl8xxxu_write32(priv, REG_OFDM0_XB_TX_IQ_IMBALANCE, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_ENERGY_CCA_THRES); |
| val32 &= ~BIT(25); |
| if ((y * oldval >> 7) & 0x1) |
| val32 |= BIT(25); |
| rtl8xxxu_write32(priv, REG_OFDM0_ENERGY_CCA_THRES, val32); |
| |
| if (tx_only) { |
| dev_dbg(&priv->udev->dev, "%s: only TX\n", __func__); |
| return; |
| } |
| |
| reg = result[candidate][6]; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_RX_IQ_IMBALANCE); |
| val32 &= ~0x3ff; |
| val32 |= (reg & 0x3ff); |
| rtl8xxxu_write32(priv, REG_OFDM0_XB_RX_IQ_IMBALANCE, val32); |
| |
| reg = result[candidate][7] & 0x3f; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_RX_IQ_IMBALANCE); |
| val32 &= ~0xfc00; |
| val32 |= ((reg << 10) & 0xfc00); |
| rtl8xxxu_write32(priv, REG_OFDM0_XB_RX_IQ_IMBALANCE, val32); |
| |
| reg = (result[candidate][7] >> 6) & 0xf; |
| |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_AGCR_SSI_TABLE); |
| val32 &= ~0x0000f000; |
| val32 |= (reg << 12); |
| rtl8xxxu_write32(priv, REG_OFDM0_AGCR_SSI_TABLE, val32); |
| } |
| |
| #define MAX_TOLERANCE 5 |
| |
| static bool rtl8xxxu_simularity_compare(struct rtl8xxxu_priv *priv, |
| int result[][8], int c1, int c2) |
| { |
| u32 i, j, diff, simubitmap, bound = 0; |
| int candidate[2] = {-1, -1}; /* for path A and path B */ |
| bool retval = true; |
| |
| if (priv->tx_paths > 1) |
| bound = 8; |
| else |
| bound = 4; |
| |
| simubitmap = 0; |
| |
| for (i = 0; i < bound; i++) { |
| diff = (result[c1][i] > result[c2][i]) ? |
| (result[c1][i] - result[c2][i]) : |
| (result[c2][i] - result[c1][i]); |
| if (diff > MAX_TOLERANCE) { |
| if ((i == 2 || i == 6) && !simubitmap) { |
| if (result[c1][i] + result[c1][i + 1] == 0) |
| candidate[(i / 4)] = c2; |
| else if (result[c2][i] + result[c2][i + 1] == 0) |
| candidate[(i / 4)] = c1; |
| else |
| simubitmap = simubitmap | (1 << i); |
| } else { |
| simubitmap = simubitmap | (1 << i); |
| } |
| } |
| } |
| |
| if (simubitmap == 0) { |
| for (i = 0; i < (bound / 4); i++) { |
| if (candidate[i] >= 0) { |
| for (j = i * 4; j < (i + 1) * 4 - 2; j++) |
| result[3][j] = result[candidate[i]][j]; |
| retval = false; |
| } |
| } |
| return retval; |
| } else if (!(simubitmap & 0x0f)) { |
| /* path A OK */ |
| for (i = 0; i < 4; i++) |
| result[3][i] = result[c1][i]; |
| } else if (!(simubitmap & 0xf0) && priv->tx_paths > 1) { |
| /* path B OK */ |
| for (i = 4; i < 8; i++) |
| result[3][i] = result[c1][i]; |
| } |
| |
| return false; |
| } |
| |
| static bool rtl8723bu_simularity_compare(struct rtl8xxxu_priv *priv, |
| int result[][8], int c1, int c2) |
| { |
| u32 i, j, diff, simubitmap, bound = 0; |
| int candidate[2] = {-1, -1}; /* for path A and path B */ |
| int tmp1, tmp2; |
| bool retval = true; |
| |
| if (priv->tx_paths > 1) |
| bound = 8; |
| else |
| bound = 4; |
| |
| simubitmap = 0; |
| |
| for (i = 0; i < bound; i++) { |
| if (i & 1) { |
| if ((result[c1][i] & 0x00000200)) |
| tmp1 = result[c1][i] | 0xfffffc00; |
| else |
| tmp1 = result[c1][i]; |
| |
| if ((result[c2][i]& 0x00000200)) |
| tmp2 = result[c2][i] | 0xfffffc00; |
| else |
| tmp2 = result[c2][i]; |
| } else { |
| tmp1 = result[c1][i]; |
| tmp2 = result[c2][i]; |
| } |
| |
| diff = (tmp1 > tmp2) ? (tmp1 - tmp2) : (tmp2 - tmp1); |
| |
| if (diff > MAX_TOLERANCE) { |
| if ((i == 2 || i == 6) && !simubitmap) { |
| if (result[c1][i] + result[c1][i + 1] == 0) |
| candidate[(i / 4)] = c2; |
| else if (result[c2][i] + result[c2][i + 1] == 0) |
| candidate[(i / 4)] = c1; |
| else |
| simubitmap = simubitmap | (1 << i); |
| } else { |
| simubitmap = simubitmap | (1 << i); |
| } |
| } |
| } |
| |
| if (simubitmap == 0) { |
| for (i = 0; i < (bound / 4); i++) { |
| if (candidate[i] >= 0) { |
| for (j = i * 4; j < (i + 1) * 4 - 2; j++) |
| result[3][j] = result[candidate[i]][j]; |
| retval = false; |
| } |
| } |
| return retval; |
| } else { |
| if (!(simubitmap & 0x03)) { |
| /* path A TX OK */ |
| for (i = 0; i < 2; i++) |
| result[3][i] = result[c1][i]; |
| } |
| |
| if (!(simubitmap & 0x0c)) { |
| /* path A RX OK */ |
| for (i = 2; i < 4; i++) |
| result[3][i] = result[c1][i]; |
| } |
| |
| if (!(simubitmap & 0x30) && priv->tx_paths > 1) { |
| /* path B RX OK */ |
| for (i = 4; i < 6; i++) |
| result[3][i] = result[c1][i]; |
| } |
| |
| if (!(simubitmap & 0x30) && priv->tx_paths > 1) { |
| /* path B RX OK */ |
| for (i = 6; i < 8; i++) |
| result[3][i] = result[c1][i]; |
| } |
| } |
| |
| return false; |
| } |
| |
| static void |
| rtl8xxxu_save_mac_regs(struct rtl8xxxu_priv *priv, const u32 *reg, u32 *backup) |
| { |
| int i; |
| |
| for (i = 0; i < (RTL8XXXU_MAC_REGS - 1); i++) |
| backup[i] = rtl8xxxu_read8(priv, reg[i]); |
| |
| backup[i] = rtl8xxxu_read32(priv, reg[i]); |
| } |
| |
| static void rtl8xxxu_restore_mac_regs(struct rtl8xxxu_priv *priv, |
| const u32 *reg, u32 *backup) |
| { |
| int i; |
| |
| for (i = 0; i < (RTL8XXXU_MAC_REGS - 1); i++) |
| rtl8xxxu_write8(priv, reg[i], backup[i]); |
| |
| rtl8xxxu_write32(priv, reg[i], backup[i]); |
| } |
| |
| static void rtl8xxxu_save_regs(struct rtl8xxxu_priv *priv, const u32 *regs, |
| u32 *backup, int count) |
| { |
| int i; |
| |
| for (i = 0; i < count; i++) |
| backup[i] = rtl8xxxu_read32(priv, regs[i]); |
| } |
| |
| static void rtl8xxxu_restore_regs(struct rtl8xxxu_priv *priv, const u32 *regs, |
| u32 *backup, int count) |
| { |
| int i; |
| |
| for (i = 0; i < count; i++) |
| rtl8xxxu_write32(priv, regs[i], backup[i]); |
| } |
| |
| |
| static void rtl8xxxu_path_adda_on(struct rtl8xxxu_priv *priv, const u32 *regs, |
| bool path_a_on) |
| { |
| u32 path_on; |
| int i; |
| |
| if (priv->tx_paths == 1) { |
| path_on = priv->fops->adda_1t_path_on; |
| rtl8xxxu_write32(priv, regs[0], priv->fops->adda_1t_init); |
| } else { |
| path_on = path_a_on ? priv->fops->adda_2t_path_on_a : |
| priv->fops->adda_2t_path_on_b; |
| |
| rtl8xxxu_write32(priv, regs[0], path_on); |
| } |
| |
| for (i = 1 ; i < RTL8XXXU_ADDA_REGS ; i++) |
| rtl8xxxu_write32(priv, regs[i], path_on); |
| } |
| |
| static void rtl8xxxu_mac_calibration(struct rtl8xxxu_priv *priv, |
| const u32 *regs, u32 *backup) |
| { |
| int i = 0; |
| |
| rtl8xxxu_write8(priv, regs[i], 0x3f); |
| |
| for (i = 1 ; i < (RTL8XXXU_MAC_REGS - 1); i++) |
| rtl8xxxu_write8(priv, regs[i], (u8)(backup[i] & ~BIT(3))); |
| |
| rtl8xxxu_write8(priv, regs[i], (u8)(backup[i] & ~BIT(5))); |
| } |
| |
| static int rtl8xxxu_iqk_path_a(struct rtl8xxxu_priv *priv) |
| { |
| u32 reg_eac, reg_e94, reg_e9c, reg_ea4, val32; |
| int result = 0; |
| |
| /* path-A IQK setting */ |
| rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x10008c1f); |
| rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x10008c1f); |
| rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82140102); |
| |
| val32 = (priv->rf_paths > 1) ? 0x28160202 : |
| /*IS_81xxC_VENDOR_UMC_B_CUT(pHalData->VersionID)?0x28160202: */ |
| 0x28160502; |
| rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, val32); |
| |
| /* path-B IQK setting */ |
| if (priv->rf_paths > 1) { |
| rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x10008c22); |
| rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x10008c22); |
| rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82140102); |
| rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28160202); |
| } |
| |
| /* LO calibration setting */ |
| rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x001028d1); |
| |
| /* One shot, path A LOK & IQK */ |
| rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000); |
| rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000); |
| |
| mdelay(1); |
| |
| /* Check failed */ |
| reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); |
| reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A); |
| reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A); |
| reg_ea4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_A_2); |
| |
| if (!(reg_eac & BIT(28)) && |
| ((reg_e94 & 0x03ff0000) != 0x01420000) && |
| ((reg_e9c & 0x03ff0000) != 0x00420000)) |
| result |= 0x01; |
| else /* If TX not OK, ignore RX */ |
| goto out; |
| |
| /* If TX is OK, check whether RX is OK */ |
| if (!(reg_eac & BIT(27)) && |
| ((reg_ea4 & 0x03ff0000) != 0x01320000) && |
| ((reg_eac & 0x03ff0000) != 0x00360000)) |
| result |= 0x02; |
| else |
| dev_warn(&priv->udev->dev, "%s: Path A RX IQK failed!\n", |
| __func__); |
| out: |
| return result; |
| } |
| |
| static int rtl8xxxu_iqk_path_b(struct rtl8xxxu_priv *priv) |
| { |
| u32 reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc; |
| int result = 0; |
| |
| /* One shot, path B LOK & IQK */ |
| rtl8xxxu_write32(priv, REG_IQK_AGC_CONT, 0x00000002); |
| rtl8xxxu_write32(priv, REG_IQK_AGC_CONT, 0x00000000); |
| |
| mdelay(1); |
| |
| /* Check failed */ |
| reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); |
| reg_eb4 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B); |
| reg_ebc = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B); |
| reg_ec4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_B_2); |
| reg_ecc = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_B_2); |
| |
| if (!(reg_eac & BIT(31)) && |
| ((reg_eb4 & 0x03ff0000) != 0x01420000) && |
| ((reg_ebc & 0x03ff0000) != 0x00420000)) |
| result |= 0x01; |
| else |
| goto out; |
| |
| if (!(reg_eac & BIT(30)) && |
| (((reg_ec4 & 0x03ff0000) >> 16) != 0x132) && |
| (((reg_ecc & 0x03ff0000) >> 16) != 0x36)) |
| result |= 0x02; |
| else |
| dev_warn(&priv->udev->dev, "%s: Path B RX IQK failed!\n", |
| __func__); |
| out: |
| return result; |
| } |
| |
| static int rtl8723bu_iqk_path_a(struct rtl8xxxu_priv *priv) |
| { |
| u32 reg_eac, reg_e94, reg_e9c, path_sel, val32; |
| int result = 0; |
| |
| path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH); |
| |
| /* |
| * Leave IQK mode |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| /* |
| * Enable path A PA in TX IQK mode |
| */ |
| val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); |
| val32 |= 0x80000; |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x20000); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0003f); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xc7f87); |
| |
| /* |
| * Tx IQK setting |
| */ |
| rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00); |
| rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800); |
| |
| /* path-A IQK setting */ |
| rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c); |
| rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c); |
| rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c); |
| rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c); |
| |
| rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x821403ea); |
| rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000); |
| rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000); |
| rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000); |
| |
| /* LO calibration setting */ |
| rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x00462911); |
| |
| /* |
| * Enter IQK mode |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| val32 |= 0x80800000; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| /* |
| * The vendor driver indicates the USB module is always using |
| * S0S1 path 1 for the 8723bu. This may be different for 8192eu |
| */ |
| if (priv->rf_paths > 1) |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000); |
| else |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280); |
| |
| /* |
| * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu. |
| * No trace of this in the 8192eu or 8188eu vendor drivers. |
| */ |
| rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800); |
| |
| /* One shot, path A LOK & IQK */ |
| rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000); |
| rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000); |
| |
| mdelay(1); |
| |
| /* Restore Ant Path */ |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel); |
| #ifdef RTL8723BU_BT |
| /* GNT_BT = 1 */ |
| rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800); |
| #endif |
| |
| /* |
| * Leave IQK mode |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| /* Check failed */ |
| reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); |
| reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A); |
| reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A); |
| |
| val32 = (reg_e9c >> 16) & 0x3ff; |
| if (val32 & 0x200) |
| val32 = 0x400 - val32; |
| |
| if (!(reg_eac & BIT(28)) && |
| ((reg_e94 & 0x03ff0000) != 0x01420000) && |
| ((reg_e9c & 0x03ff0000) != 0x00420000) && |
| ((reg_e94 & 0x03ff0000) < 0x01100000) && |
| ((reg_e94 & 0x03ff0000) > 0x00f00000) && |
| val32 < 0xf) |
| result |= 0x01; |
| else /* If TX not OK, ignore RX */ |
| goto out; |
| |
| out: |
| return result; |
| } |
| |
| static int rtl8723bu_rx_iqk_path_a(struct rtl8xxxu_priv *priv) |
| { |
| u32 reg_ea4, reg_eac, reg_e94, reg_e9c, path_sel, val32; |
| int result = 0; |
| |
| path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH); |
| |
| /* |
| * Leave IQK mode |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| /* |
| * Enable path A PA in TX IQK mode |
| */ |
| val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); |
| val32 |= 0x80000; |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7); |
| |
| /* |
| * Tx IQK setting |
| */ |
| rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00); |
| rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800); |
| |
| /* path-A IQK setting */ |
| rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c); |
| rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c); |
| rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c); |
| rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c); |
| |
| rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160ff0); |
| rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000); |
| rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000); |
| rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000); |
| |
| /* LO calibration setting */ |
| rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911); |
| |
| /* |
| * Enter IQK mode |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| val32 |= 0x80800000; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| /* |
| * The vendor driver indicates the USB module is always using |
| * S0S1 path 1 for the 8723bu. This may be different for 8192eu |
| */ |
| if (priv->rf_paths > 1) |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000); |
| else |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280); |
| |
| /* |
| * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu. |
| * No trace of this in the 8192eu or 8188eu vendor drivers. |
| */ |
| rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800); |
| |
| /* One shot, path A LOK & IQK */ |
| rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000); |
| rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000); |
| |
| mdelay(1); |
| |
| /* Restore Ant Path */ |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel); |
| #ifdef RTL8723BU_BT |
| /* GNT_BT = 1 */ |
| rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800); |
| #endif |
| |
| /* |
| * Leave IQK mode |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| /* Check failed */ |
| reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); |
| reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A); |
| reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A); |
| |
| val32 = (reg_e9c >> 16) & 0x3ff; |
| if (val32 & 0x200) |
| val32 = 0x400 - val32; |
| |
| if (!(reg_eac & BIT(28)) && |
| ((reg_e94 & 0x03ff0000) != 0x01420000) && |
| ((reg_e9c & 0x03ff0000) != 0x00420000) && |
| ((reg_e94 & 0x03ff0000) < 0x01100000) && |
| ((reg_e94 & 0x03ff0000) > 0x00f00000) && |
| val32 < 0xf) |
| result |= 0x01; |
| else /* If TX not OK, ignore RX */ |
| goto out; |
| |
| val32 = 0x80007c00 | (reg_e94 &0x3ff0000) | |
| ((reg_e9c & 0x3ff0000) >> 16); |
| rtl8xxxu_write32(priv, REG_TX_IQK, val32); |
| |
| /* |
| * Modify RX IQK mode |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); |
| val32 |= 0x80000; |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7d77); |
| |
| /* |
| * PA, PAD setting |
| */ |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0xf80); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_55, 0x4021f); |
| |
| /* |
| * RX IQK setting |
| */ |
| rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800); |
| |
| /* path-A IQK setting */ |
| rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c); |
| rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x18008c1c); |
| rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c); |
| rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c); |
| |
| rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82110000); |
| rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x2816001f); |
| rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000); |
| rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000); |
| |
| /* LO calibration setting */ |
| rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a8d1); |
| |
| /* |
| * Enter IQK mode |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| val32 |= 0x80800000; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| if (priv->rf_paths > 1) |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000); |
| else |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280); |
| |
| /* |
| * Disable BT |
| */ |
| rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800); |
| |
| /* One shot, path A LOK & IQK */ |
| rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000); |
| rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000); |
| |
| mdelay(1); |
| |
| /* Restore Ant Path */ |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel); |
| #ifdef RTL8723BU_BT |
| /* GNT_BT = 1 */ |
| rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800); |
| #endif |
| |
| /* |
| * Leave IQK mode |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| /* Check failed */ |
| reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); |
| reg_ea4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_A_2); |
| |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x780); |
| |
| val32 = (reg_eac >> 16) & 0x3ff; |
| if (val32 & 0x200) |
| val32 = 0x400 - val32; |
| |
| if (!(reg_eac & BIT(27)) && |
| ((reg_ea4 & 0x03ff0000) != 0x01320000) && |
| ((reg_eac & 0x03ff0000) != 0x00360000) && |
| ((reg_ea4 & 0x03ff0000) < 0x01100000) && |
| ((reg_ea4 & 0x03ff0000) > 0x00f00000) && |
| val32 < 0xf) |
| result |= 0x02; |
| else /* If TX not OK, ignore RX */ |
| goto out; |
| out: |
| return result; |
| } |
| |
| #ifdef RTL8723BU_PATH_B |
| static int rtl8723bu_iqk_path_b(struct rtl8xxxu_priv *priv) |
| { |
| u32 reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc, path_sel; |
| int result = 0; |
| |
| path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| /* One shot, path B LOK & IQK */ |
| rtl8xxxu_write32(priv, REG_IQK_AGC_CONT, 0x00000002); |
| rtl8xxxu_write32(priv, REG_IQK_AGC_CONT, 0x00000000); |
| |
| mdelay(1); |
| |
| /* Check failed */ |
| reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); |
| reg_eb4 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B); |
| reg_ebc = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B); |
| reg_ec4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_B_2); |
| reg_ecc = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_B_2); |
| |
| if (!(reg_eac & BIT(31)) && |
| ((reg_eb4 & 0x03ff0000) != 0x01420000) && |
| ((reg_ebc & 0x03ff0000) != 0x00420000)) |
| result |= 0x01; |
| else |
| goto out; |
| |
| if (!(reg_eac & BIT(30)) && |
| (((reg_ec4 & 0x03ff0000) >> 16) != 0x132) && |
| (((reg_ecc & 0x03ff0000) >> 16) != 0x36)) |
| result |= 0x02; |
| else |
| dev_warn(&priv->udev->dev, "%s: Path B RX IQK failed!\n", |
| __func__); |
| out: |
| return result; |
| } |
| #endif |
| |
| static void rtl8xxxu_phy_iqcalibrate(struct rtl8xxxu_priv *priv, |
| int result[][8], int t) |
| { |
| struct device *dev = &priv->udev->dev; |
| u32 i, val32; |
| int path_a_ok, path_b_ok; |
| int retry = 2; |
| const u32 adda_regs[RTL8XXXU_ADDA_REGS] = { |
| REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH, |
| REG_RX_WAIT_CCA, REG_TX_CCK_RFON, |
| REG_TX_CCK_BBON, REG_TX_OFDM_RFON, |
| REG_TX_OFDM_BBON, REG_TX_TO_RX, |
| REG_TX_TO_TX, REG_RX_CCK, |
| REG_RX_OFDM, REG_RX_WAIT_RIFS, |
| REG_RX_TO_RX, REG_STANDBY, |
| REG_SLEEP, REG_PMPD_ANAEN |
| }; |
| const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = { |
| REG_TXPAUSE, REG_BEACON_CTRL, |
| REG_BEACON_CTRL_1, REG_GPIO_MUXCFG |
| }; |
| const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = { |
| REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR, |
| REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B, |
| REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE, |
| REG_FPGA0_XB_RF_INT_OE, REG_FPGA0_RF_MODE |
| }; |
| |
| /* |
| * Note: IQ calibration must be performed after loading |
| * PHY_REG.txt , and radio_a, radio_b.txt |
| */ |
| |
| if (t == 0) { |
| /* Save ADDA parameters, turn Path A ADDA on */ |
| rtl8xxxu_save_regs(priv, adda_regs, priv->adda_backup, |
| RTL8XXXU_ADDA_REGS); |
| rtl8xxxu_save_mac_regs(priv, iqk_mac_regs, priv->mac_backup); |
| rtl8xxxu_save_regs(priv, iqk_bb_regs, |
| priv->bb_backup, RTL8XXXU_BB_REGS); |
| } |
| |
| rtl8xxxu_path_adda_on(priv, adda_regs, true); |
| |
| if (t == 0) { |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_XA_HSSI_PARM1); |
| if (val32 & FPGA0_HSSI_PARM1_PI) |
| priv->pi_enabled = 1; |
| } |
| |
| if (!priv->pi_enabled) { |
| /* Switch BB to PI mode to do IQ Calibration. */ |
| rtl8xxxu_write32(priv, REG_FPGA0_XA_HSSI_PARM1, 0x01000100); |
| rtl8xxxu_write32(priv, REG_FPGA0_XB_HSSI_PARM1, 0x01000100); |
| } |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE); |
| val32 &= ~FPGA_RF_MODE_CCK; |
| rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32); |
| |
| rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, 0x03a05600); |
| rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4); |
| rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22204000); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_XAB_RF_SW_CTRL); |
| val32 |= (FPGA0_RF_PAPE | (FPGA0_RF_PAPE << FPGA0_RF_BD_CTRL_SHIFT)); |
| rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_SW_CTRL, val32); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_XA_RF_INT_OE); |
| val32 &= ~BIT(10); |
| rtl8xxxu_write32(priv, REG_FPGA0_XA_RF_INT_OE, val32); |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_XB_RF_INT_OE); |
| val32 &= ~BIT(10); |
| rtl8xxxu_write32(priv, REG_FPGA0_XB_RF_INT_OE, val32); |
| |
| if (priv->tx_paths > 1) { |
| rtl8xxxu_write32(priv, REG_FPGA0_XA_LSSI_PARM, 0x00010000); |
| rtl8xxxu_write32(priv, REG_FPGA0_XB_LSSI_PARM, 0x00010000); |
| } |
| |
| /* MAC settings */ |
| rtl8xxxu_mac_calibration(priv, iqk_mac_regs, priv->mac_backup); |
| |
| /* Page B init */ |
| rtl8xxxu_write32(priv, REG_CONFIG_ANT_A, 0x00080000); |
| |
| if (priv->tx_paths > 1) |
| rtl8xxxu_write32(priv, REG_CONFIG_ANT_B, 0x00080000); |
| |
| /* IQ calibration setting */ |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000); |
| rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00); |
| rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800); |
| |
| for (i = 0; i < retry; i++) { |
| path_a_ok = rtl8xxxu_iqk_path_a(priv); |
| if (path_a_ok == 0x03) { |
| val32 = rtl8xxxu_read32(priv, |
| REG_TX_POWER_BEFORE_IQK_A); |
| result[t][0] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, |
| REG_TX_POWER_AFTER_IQK_A); |
| result[t][1] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, |
| REG_RX_POWER_BEFORE_IQK_A_2); |
| result[t][2] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, |
| REG_RX_POWER_AFTER_IQK_A_2); |
| result[t][3] = (val32 >> 16) & 0x3ff; |
| break; |
| } else if (i == (retry - 1) && path_a_ok == 0x01) { |
| /* TX IQK OK */ |
| dev_dbg(dev, "%s: Path A IQK Only Tx Success!!\n", |
| __func__); |
| |
| val32 = rtl8xxxu_read32(priv, |
| REG_TX_POWER_BEFORE_IQK_A); |
| result[t][0] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, |
| REG_TX_POWER_AFTER_IQK_A); |
| result[t][1] = (val32 >> 16) & 0x3ff; |
| } |
| } |
| |
| if (!path_a_ok) |
| dev_dbg(dev, "%s: Path A IQK failed!\n", __func__); |
| |
| if (priv->tx_paths > 1) { |
| /* |
| * Path A into standby |
| */ |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x0); |
| rtl8xxxu_write32(priv, REG_FPGA0_XA_LSSI_PARM, 0x00010000); |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000); |
| |
| /* Turn Path B ADDA on */ |
| rtl8xxxu_path_adda_on(priv, adda_regs, false); |
| |
| for (i = 0; i < retry; i++) { |
| path_b_ok = rtl8xxxu_iqk_path_b(priv); |
| if (path_b_ok == 0x03) { |
| val32 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B); |
| result[t][4] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B); |
| result[t][5] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_B_2); |
| result[t][6] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_B_2); |
| result[t][7] = (val32 >> 16) & 0x3ff; |
| break; |
| } else if (i == (retry - 1) && path_b_ok == 0x01) { |
| /* TX IQK OK */ |
| val32 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B); |
| result[t][4] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B); |
| result[t][5] = (val32 >> 16) & 0x3ff; |
| } |
| } |
| |
| if (!path_b_ok) |
| dev_dbg(dev, "%s: Path B IQK failed!\n", __func__); |
| } |
| |
| /* Back to BB mode, load original value */ |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0); |
| |
| if (t) { |
| if (!priv->pi_enabled) { |
| /* |
| * Switch back BB to SI mode after finishing |
| * IQ Calibration |
| */ |
| val32 = 0x01000000; |
| rtl8xxxu_write32(priv, REG_FPGA0_XA_HSSI_PARM1, val32); |
| rtl8xxxu_write32(priv, REG_FPGA0_XB_HSSI_PARM1, val32); |
| } |
| |
| /* Reload ADDA power saving parameters */ |
| rtl8xxxu_restore_regs(priv, adda_regs, priv->adda_backup, |
| RTL8XXXU_ADDA_REGS); |
| |
| /* Reload MAC parameters */ |
| rtl8xxxu_restore_mac_regs(priv, iqk_mac_regs, priv->mac_backup); |
| |
| /* Reload BB parameters */ |
| rtl8xxxu_restore_regs(priv, iqk_bb_regs, |
| priv->bb_backup, RTL8XXXU_BB_REGS); |
| |
| /* Restore RX initial gain */ |
| rtl8xxxu_write32(priv, REG_FPGA0_XA_LSSI_PARM, 0x00032ed3); |
| |
| if (priv->tx_paths > 1) { |
| rtl8xxxu_write32(priv, REG_FPGA0_XB_LSSI_PARM, |
| 0x00032ed3); |
| } |
| |
| /* Load 0xe30 IQC default value */ |
| rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x01008c00); |
| rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x01008c00); |
| } |
| } |
| |
| static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv, |
| int result[][8], int t) |
| { |
| struct device *dev = &priv->udev->dev; |
| u32 i, val32; |
| int path_a_ok /*, path_b_ok */; |
| int retry = 2; |
| const u32 adda_regs[RTL8XXXU_ADDA_REGS] = { |
| REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH, |
| REG_RX_WAIT_CCA, REG_TX_CCK_RFON, |
| REG_TX_CCK_BBON, REG_TX_OFDM_RFON, |
| REG_TX_OFDM_BBON, REG_TX_TO_RX, |
| REG_TX_TO_TX, REG_RX_CCK, |
| REG_RX_OFDM, REG_RX_WAIT_RIFS, |
| REG_RX_TO_RX, REG_STANDBY, |
| REG_SLEEP, REG_PMPD_ANAEN |
| }; |
| const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = { |
| REG_TXPAUSE, REG_BEACON_CTRL, |
| REG_BEACON_CTRL_1, REG_GPIO_MUXCFG |
| }; |
| const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = { |
| REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR, |
| REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B, |
| REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE, |
| REG_FPGA0_XB_RF_INT_OE, REG_FPGA0_RF_MODE |
| }; |
| u8 xa_agc = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1) & 0xff; |
| u8 xb_agc = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1) & 0xff; |
| |
| /* |
| * Note: IQ calibration must be performed after loading |
| * PHY_REG.txt , and radio_a, radio_b.txt |
| */ |
| |
| if (t == 0) { |
| /* Save ADDA parameters, turn Path A ADDA on */ |
| rtl8xxxu_save_regs(priv, adda_regs, priv->adda_backup, |
| RTL8XXXU_ADDA_REGS); |
| rtl8xxxu_save_mac_regs(priv, iqk_mac_regs, priv->mac_backup); |
| rtl8xxxu_save_regs(priv, iqk_bb_regs, |
| priv->bb_backup, RTL8XXXU_BB_REGS); |
| } |
| |
| rtl8xxxu_path_adda_on(priv, adda_regs, true); |
| |
| /* MAC settings */ |
| rtl8xxxu_mac_calibration(priv, iqk_mac_regs, priv->mac_backup); |
| |
| val32 = rtl8xxxu_read32(priv, REG_CCK0_AFE_SETTING); |
| val32 |= 0x0f000000; |
| rtl8xxxu_write32(priv, REG_CCK0_AFE_SETTING, val32); |
| |
| rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, 0x03a05600); |
| rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4); |
| rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22204000); |
| |
| #ifdef RTL8723BU_PATH_B |
| /* Set RF mode to standby Path B */ |
| if (priv->tx_paths > 1) |
| rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_AC, 0x10000); |
| #endif |
| |
| #if 0 |
| /* Page B init */ |
| rtl8xxxu_write32(priv, REG_CONFIG_ANT_A, 0x0f600000); |
| |
| if (priv->tx_paths > 1) |
| rtl8xxxu_write32(priv, REG_CONFIG_ANT_B, 0x0f600000); |
| #endif |
| |
| /* |
| * RX IQ calibration setting for 8723B D cut large current issue |
| * when leaving IPS |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); |
| val32 |= 0x80000; |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); |
| |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7); |
| |
| val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED); |
| val32 |= 0x20; |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32); |
| |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_43, 0x60fbd); |
| |
| for (i = 0; i < retry; i++) { |
| path_a_ok = rtl8723bu_iqk_path_a(priv); |
| if (path_a_ok == 0x01) { |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| #if 0 /* Only needed in restore case, we may need this when going to suspend */ |
| priv->RFCalibrateInfo.TxLOK[RF_A] = |
| rtl8xxxu_read_rfreg(priv, RF_A, |
| RF6052_REG_TXM_IDAC); |
| #endif |
| |
| val32 = rtl8xxxu_read32(priv, |
| REG_TX_POWER_BEFORE_IQK_A); |
| result[t][0] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, |
| REG_TX_POWER_AFTER_IQK_A); |
| result[t][1] = (val32 >> 16) & 0x3ff; |
| |
| break; |
| } |
| } |
| |
| if (!path_a_ok) |
| dev_dbg(dev, "%s: Path A TX IQK failed!\n", __func__); |
| |
| for (i = 0; i < retry; i++) { |
| path_a_ok = rtl8723bu_rx_iqk_path_a(priv); |
| if (path_a_ok == 0x03) { |
| val32 = rtl8xxxu_read32(priv, |
| REG_RX_POWER_BEFORE_IQK_A_2); |
| result[t][2] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, |
| REG_RX_POWER_AFTER_IQK_A_2); |
| result[t][3] = (val32 >> 16) & 0x3ff; |
| |
| break; |
| } |
| } |
| |
| if (!path_a_ok) |
| dev_dbg(dev, "%s: Path A RX IQK failed!\n", __func__); |
| |
| if (priv->tx_paths > 1) { |
| #if 1 |
| dev_warn(dev, "%s: Path B not supported\n", __func__); |
| #else |
| |
| /* |
| * Path A into standby |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, 0x10000); |
| |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| val32 |= 0x80800000; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| /* Turn Path B ADDA on */ |
| rtl8xxxu_path_adda_on(priv, adda_regs, false); |
| |
| for (i = 0; i < retry; i++) { |
| path_b_ok = rtl8xxxu_iqk_path_b(priv); |
| if (path_b_ok == 0x03) { |
| val32 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B); |
| result[t][4] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B); |
| result[t][5] = (val32 >> 16) & 0x3ff; |
| break; |
| } |
| } |
| |
| if (!path_b_ok) |
| dev_dbg(dev, "%s: Path B IQK failed!\n", __func__); |
| |
| for (i = 0; i < retry; i++) { |
| path_b_ok = rtl8723bu_rx_iqk_path_b(priv); |
| if (path_a_ok == 0x03) { |
| val32 = rtl8xxxu_read32(priv, |
| REG_RX_POWER_BEFORE_IQK_B_2); |
| result[t][6] = (val32 >> 16) & 0x3ff; |
| val32 = rtl8xxxu_read32(priv, |
| REG_RX_POWER_AFTER_IQK_B_2); |
| result[t][7] = (val32 >> 16) & 0x3ff; |
| break; |
| } |
| } |
| |
| if (!path_b_ok) |
| dev_dbg(dev, "%s: Path B RX IQK failed!\n", __func__); |
| #endif |
| } |
| |
| /* Back to BB mode, load original value */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 &= 0x000000ff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| |
| if (t) { |
| /* Reload ADDA power saving parameters */ |
| rtl8xxxu_restore_regs(priv, adda_regs, priv->adda_backup, |
| RTL8XXXU_ADDA_REGS); |
| |
| /* Reload MAC parameters */ |
| rtl8xxxu_restore_mac_regs(priv, iqk_mac_regs, priv->mac_backup); |
| |
| /* Reload BB parameters */ |
| rtl8xxxu_restore_regs(priv, iqk_bb_regs, |
| priv->bb_backup, RTL8XXXU_BB_REGS); |
| |
| /* Restore RX initial gain */ |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1); |
| val32 &= 0xffffff00; |
| rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | 0x50); |
| rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | xa_agc); |
| |
| if (priv->tx_paths > 1) { |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1); |
| val32 &= 0xffffff00; |
| rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1, |
| val32 | 0x50); |
| rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1, |
| val32 | xb_agc); |
| } |
| |
| /* Load 0xe30 IQC default value */ |
| rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x01008c00); |
| rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x01008c00); |
| } |
| } |
| |
| static void rtl8xxxu_prepare_calibrate(struct rtl8xxxu_priv *priv, u8 start) |
| { |
| struct h2c_cmd h2c; |
| |
| if (priv->fops->mbox_ext_width < 4) |
| return; |
| |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| h2c.bt_wlan_calibration.cmd = H2C_8723B_BT_WLAN_CALIBRATION; |
| h2c.bt_wlan_calibration.data = start; |
| |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_wlan_calibration)); |
| } |
| |
| static void rtl8723au_phy_iq_calibrate(struct rtl8xxxu_priv *priv) |
| { |
| struct device *dev = &priv->udev->dev; |
| int result[4][8]; /* last is final result */ |
| int i, candidate; |
| bool path_a_ok, path_b_ok; |
| u32 reg_e94, reg_e9c, reg_ea4, reg_eac; |
| u32 reg_eb4, reg_ebc, reg_ec4, reg_ecc; |
| s32 reg_tmp = 0; |
| bool simu; |
| |
| rtl8xxxu_prepare_calibrate(priv, 1); |
| |
| memset(result, 0, sizeof(result)); |
| candidate = -1; |
| |
| path_a_ok = false; |
| path_b_ok = false; |
| |
| rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE); |
| |
| for (i = 0; i < 3; i++) { |
| rtl8xxxu_phy_iqcalibrate(priv, result, i); |
| |
| if (i == 1) { |
| simu = rtl8xxxu_simularity_compare(priv, result, 0, 1); |
| if (simu) { |
| candidate = 0; |
| break; |
| } |
| } |
| |
| if (i == 2) { |
| simu = rtl8xxxu_simularity_compare(priv, result, 0, 2); |
| if (simu) { |
| candidate = 0; |
| break; |
| } |
| |
| simu = rtl8xxxu_simularity_compare(priv, result, 1, 2); |
| if (simu) { |
| candidate = 1; |
| } else { |
| for (i = 0; i < 8; i++) |
| reg_tmp += result[3][i]; |
| |
| if (reg_tmp) |
| candidate = 3; |
| else |
| candidate = -1; |
| } |
| } |
| } |
| |
| for (i = 0; i < 4; i++) { |
| reg_e94 = result[i][0]; |
| reg_e9c = result[i][1]; |
| reg_ea4 = result[i][2]; |
| reg_eac = result[i][3]; |
| reg_eb4 = result[i][4]; |
| reg_ebc = result[i][5]; |
| reg_ec4 = result[i][6]; |
| reg_ecc = result[i][7]; |
| } |
| |
| if (candidate >= 0) { |
| reg_e94 = result[candidate][0]; |
| priv->rege94 = reg_e94; |
| reg_e9c = result[candidate][1]; |
| priv->rege9c = reg_e9c; |
| reg_ea4 = result[candidate][2]; |
| reg_eac = result[candidate][3]; |
| reg_eb4 = result[candidate][4]; |
| priv->regeb4 = reg_eb4; |
| reg_ebc = result[candidate][5]; |
| priv->regebc = reg_ebc; |
| reg_ec4 = result[candidate][6]; |
| reg_ecc = result[candidate][7]; |
| dev_dbg(dev, "%s: candidate is %x\n", __func__, candidate); |
| dev_dbg(dev, |
| "%s: e94 =%x e9c=%x ea4=%x eac=%x eb4=%x ebc=%x ec4=%x " |
| "ecc=%x\n ", __func__, reg_e94, reg_e9c, |
| reg_ea4, reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc); |
| path_a_ok = true; |
| path_b_ok = true; |
| } else { |
| reg_e94 = reg_eb4 = priv->rege94 = priv->regeb4 = 0x100; |
| reg_e9c = reg_ebc = priv->rege9c = priv->regebc = 0x0; |
| } |
| |
| if (reg_e94 && candidate >= 0) |
| rtl8xxxu_fill_iqk_matrix_a(priv, path_a_ok, result, |
| candidate, (reg_ea4 == 0)); |
| |
| if (priv->tx_paths > 1 && reg_eb4) |
| rtl8xxxu_fill_iqk_matrix_b(priv, path_b_ok, result, |
| candidate, (reg_ec4 == 0)); |
| |
| rtl8xxxu_save_regs(priv, rtl8723au_iqk_phy_iq_bb_reg, |
| priv->bb_recovery_backup, RTL8XXXU_BB_REGS); |
| |
| rtl8xxxu_prepare_calibrate(priv, 0); |
| } |
| |
| static void rtl8723bu_phy_iq_calibrate(struct rtl8xxxu_priv *priv) |
| { |
| struct device *dev = &priv->udev->dev; |
| int result[4][8]; /* last is final result */ |
| int i, candidate; |
| bool path_a_ok, path_b_ok; |
| u32 reg_e94, reg_e9c, reg_ea4, reg_eac; |
| u32 reg_eb4, reg_ebc, reg_ec4, reg_ecc; |
| u32 val32, bt_control; |
| s32 reg_tmp = 0; |
| bool simu; |
| |
| rtl8xxxu_prepare_calibrate(priv, 1); |
| |
| memset(result, 0, sizeof(result)); |
| candidate = -1; |
| |
| path_a_ok = false; |
| path_b_ok = false; |
| |
| bt_control = rtl8xxxu_read32(priv, REG_BT_CONTROL_8723BU); |
| |
| for (i = 0; i < 3; i++) { |
| rtl8723bu_phy_iqcalibrate(priv, result, i); |
| |
| if (i == 1) { |
| simu = rtl8723bu_simularity_compare(priv, result, 0, 1); |
| if (simu) { |
| candidate = 0; |
| break; |
| } |
| } |
| |
| if (i == 2) { |
| simu = rtl8723bu_simularity_compare(priv, result, 0, 2); |
| if (simu) { |
| candidate = 0; |
| break; |
| } |
| |
| simu = rtl8723bu_simularity_compare(priv, result, 1, 2); |
| if (simu) { |
| candidate = 1; |
| } else { |
| for (i = 0; i < 8; i++) |
| reg_tmp += result[3][i]; |
| |
| if (reg_tmp) |
| candidate = 3; |
| else |
| candidate = -1; |
| } |
| } |
| } |
| |
| for (i = 0; i < 4; i++) { |
| reg_e94 = result[i][0]; |
| reg_e9c = result[i][1]; |
| reg_ea4 = result[i][2]; |
| reg_eac = result[i][3]; |
| reg_eb4 = result[i][4]; |
| reg_ebc = result[i][5]; |
| reg_ec4 = result[i][6]; |
| reg_ecc = result[i][7]; |
| } |
| |
| if (candidate >= 0) { |
| reg_e94 = result[candidate][0]; |
| priv->rege94 = reg_e94; |
| reg_e9c = result[candidate][1]; |
| priv->rege9c = reg_e9c; |
| reg_ea4 = result[candidate][2]; |
| reg_eac = result[candidate][3]; |
| reg_eb4 = result[candidate][4]; |
| priv->regeb4 = reg_eb4; |
| reg_ebc = result[candidate][5]; |
| priv->regebc = reg_ebc; |
| reg_ec4 = result[candidate][6]; |
| reg_ecc = result[candidate][7]; |
| dev_dbg(dev, "%s: candidate is %x\n", __func__, candidate); |
| dev_dbg(dev, |
| "%s: e94 =%x e9c=%x ea4=%x eac=%x eb4=%x ebc=%x ec4=%x " |
| "ecc=%x\n ", __func__, reg_e94, reg_e9c, |
| reg_ea4, reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc); |
| path_a_ok = true; |
| path_b_ok = true; |
| } else { |
| reg_e94 = reg_eb4 = priv->rege94 = priv->regeb4 = 0x100; |
| reg_e9c = reg_ebc = priv->rege9c = priv->regebc = 0x0; |
| } |
| |
| if (reg_e94 && candidate >= 0) |
| rtl8xxxu_fill_iqk_matrix_a(priv, path_a_ok, result, |
| candidate, (reg_ea4 == 0)); |
| |
| if (priv->tx_paths > 1 && reg_eb4) |
| rtl8xxxu_fill_iqk_matrix_b(priv, path_b_ok, result, |
| candidate, (reg_ec4 == 0)); |
| |
| rtl8xxxu_save_regs(priv, rtl8723au_iqk_phy_iq_bb_reg, |
| priv->bb_recovery_backup, RTL8XXXU_BB_REGS); |
| |
| rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, bt_control); |
| |
| val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); |
| val32 |= 0x80000; |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x18000); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xe6177); |
| val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED); |
| val32 |= 0x20; |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32); |
| rtl8xxxu_write_rfreg(priv, RF_A, 0x43, 0x300bd); |
| |
| if (priv->rf_paths > 1) { |
| dev_dbg(dev, "%s: beware 2T not yet supported\n", __func__); |
| #ifdef RTL8723BU_PATH_B |
| if (RF_Path == 0x0) //S1 |
| ODM_SetIQCbyRFpath(pDM_Odm, 0); |
| else //S0 |
| ODM_SetIQCbyRFpath(pDM_Odm, 1); |
| #endif |
| } |
| rtl8xxxu_prepare_calibrate(priv, 0); |
| } |
| |
| static void rtl8723a_phy_lc_calibrate(struct rtl8xxxu_priv *priv) |
| { |
| u32 val32; |
| u32 rf_amode, rf_bmode = 0, lstf; |
| |
| /* Check continuous TX and Packet TX */ |
| lstf = rtl8xxxu_read32(priv, REG_OFDM1_LSTF); |
| |
| if (lstf & OFDM_LSTF_MASK) { |
| /* Disable all continuous TX */ |
| val32 = lstf & ~OFDM_LSTF_MASK; |
| rtl8xxxu_write32(priv, REG_OFDM1_LSTF, val32); |
| |
| /* Read original RF mode Path A */ |
| rf_amode = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_AC); |
| |
| /* Set RF mode to standby Path A */ |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, |
| (rf_amode & 0x8ffff) | 0x10000); |
| |
| /* Path-B */ |
| if (priv->tx_paths > 1) { |
| rf_bmode = rtl8xxxu_read_rfreg(priv, RF_B, |
| RF6052_REG_AC); |
| |
| rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_AC, |
| (rf_bmode & 0x8ffff) | 0x10000); |
| } |
| } else { |
| /* Deal with Packet TX case */ |
| /* block all queues */ |
| rtl8xxxu_write8(priv, REG_TXPAUSE, 0xff); |
| } |
| |
| /* Start LC calibration */ |
| if (priv->fops->has_s0s1) |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_S0S1, 0xdfbe0); |
| val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_MODE_AG); |
| val32 |= 0x08000; |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_MODE_AG, val32); |
| |
| msleep(100); |
| |
| if (priv->fops->has_s0s1) |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_S0S1, 0xdffe0); |
| |
| /* Restore original parameters */ |
| if (lstf & OFDM_LSTF_MASK) { |
| /* Path-A */ |
| rtl8xxxu_write32(priv, REG_OFDM1_LSTF, lstf); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, rf_amode); |
| |
| /* Path-B */ |
| if (priv->tx_paths > 1) |
| rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_AC, |
| rf_bmode); |
| } else /* Deal with Packet TX case */ |
| rtl8xxxu_write8(priv, REG_TXPAUSE, 0x00); |
| } |
| |
| static int rtl8xxxu_set_mac(struct rtl8xxxu_priv *priv) |
| { |
| int i; |
| u16 reg; |
| |
| reg = REG_MACID; |
| |
| for (i = 0; i < ETH_ALEN; i++) |
| rtl8xxxu_write8(priv, reg + i, priv->mac_addr[i]); |
| |
| return 0; |
| } |
| |
| static int rtl8xxxu_set_bssid(struct rtl8xxxu_priv *priv, const u8 *bssid) |
| { |
| int i; |
| u16 reg; |
| |
| dev_dbg(&priv->udev->dev, "%s: (%pM)\n", __func__, bssid); |
| |
| reg = REG_BSSID; |
| |
| for (i = 0; i < ETH_ALEN; i++) |
| rtl8xxxu_write8(priv, reg + i, bssid[i]); |
| |
| return 0; |
| } |
| |
| static void |
| rtl8xxxu_set_ampdu_factor(struct rtl8xxxu_priv *priv, u8 ampdu_factor) |
| { |
| u8 vals[4] = { 0x41, 0xa8, 0x72, 0xb9 }; |
| u8 max_agg = 0xf; |
| int i; |
| |
| ampdu_factor = 1 << (ampdu_factor + 2); |
| if (ampdu_factor > max_agg) |
| ampdu_factor = max_agg; |
| |
| for (i = 0; i < 4; i++) { |
| if ((vals[i] & 0xf0) > (ampdu_factor << 4)) |
| vals[i] = (vals[i] & 0x0f) | (ampdu_factor << 4); |
| |
| if ((vals[i] & 0x0f) > ampdu_factor) |
| vals[i] = (vals[i] & 0xf0) | ampdu_factor; |
| |
| rtl8xxxu_write8(priv, REG_AGGLEN_LMT + i, vals[i]); |
| } |
| } |
| |
| static void rtl8xxxu_set_ampdu_min_space(struct rtl8xxxu_priv *priv, u8 density) |
| { |
| u8 val8; |
| |
| val8 = rtl8xxxu_read8(priv, REG_AMPDU_MIN_SPACE); |
| val8 &= 0xf8; |
| val8 |= density; |
| rtl8xxxu_write8(priv, REG_AMPDU_MIN_SPACE, val8); |
| } |
| |
| static int rtl8xxxu_active_to_emu(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| int count, ret; |
| |
| /* Start of rtl8723AU_card_enable_flow */ |
| /* Act to Cardemu sequence*/ |
| /* Turn off RF */ |
| rtl8xxxu_write8(priv, REG_RF_CTRL, 0); |
| |
| /* 0x004E[7] = 0, switch DPDT_SEL_P output from register 0x0065[2] */ |
| val8 = rtl8xxxu_read8(priv, REG_LEDCFG2); |
| val8 &= ~LEDCFG2_DPDT_SELECT; |
| rtl8xxxu_write8(priv, REG_LEDCFG2, val8); |
| |
| /* 0x0005[1] = 1 turn off MAC by HW state machine*/ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 |= BIT(1); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| |
| for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| if ((val8 & BIT(1)) == 0) |
| break; |
| udelay(10); |
| } |
| |
| if (!count) { |
| dev_warn(&priv->udev->dev, "%s: Disabling MAC timed out\n", |
| __func__); |
| ret = -EBUSY; |
| goto exit; |
| } |
| |
| /* 0x0000[5] = 1 analog Ips to digital, 1:isolation */ |
| val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL); |
| val8 |= SYS_ISO_ANALOG_IPS; |
| rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8); |
| |
| /* 0x0020[0] = 0 disable LDOA12 MACRO block*/ |
| val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL); |
| val8 &= ~LDOA15_ENABLE; |
| rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8); |
| |
| exit: |
| return ret; |
| } |
| |
| static int rtl8xxxu_active_to_lps(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| u8 val32; |
| int count, ret; |
| |
| rtl8xxxu_write8(priv, REG_TXPAUSE, 0xff); |
| |
| /* |
| * Poll - wait for RX packet to complete |
| */ |
| for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { |
| val32 = rtl8xxxu_read32(priv, 0x5f8); |
| if (!val32) |
| break; |
| udelay(10); |
| } |
| |
| if (!count) { |
| dev_warn(&priv->udev->dev, |
| "%s: RX poll timed out (0x05f8)\n", __func__); |
| ret = -EBUSY; |
| goto exit; |
| } |
| |
| /* Disable CCK and OFDM, clock gated */ |
| val8 = rtl8xxxu_read8(priv, REG_SYS_FUNC); |
| val8 &= ~SYS_FUNC_BBRSTB; |
| rtl8xxxu_write8(priv, REG_SYS_FUNC, val8); |
| |
| udelay(2); |
| |
| /* Reset baseband */ |
| val8 = rtl8xxxu_read8(priv, REG_SYS_FUNC); |
| val8 &= ~SYS_FUNC_BB_GLB_RSTN; |
| rtl8xxxu_write8(priv, REG_SYS_FUNC, val8); |
| |
| /* Reset MAC TRX */ |
| val8 = rtl8xxxu_read8(priv, REG_CR); |
| val8 = CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE; |
| rtl8xxxu_write8(priv, REG_CR, val8); |
| |
| /* Reset MAC TRX */ |
| val8 = rtl8xxxu_read8(priv, REG_CR + 1); |
| val8 &= ~BIT(1); /* CR_SECURITY_ENABLE */ |
| rtl8xxxu_write8(priv, REG_CR + 1, val8); |
| |
| /* Respond TX OK to scheduler */ |
| val8 = rtl8xxxu_read8(priv, REG_DUAL_TSF_RST); |
| val8 |= DUAL_TSF_TX_OK; |
| rtl8xxxu_write8(priv, REG_DUAL_TSF_RST, val8); |
| |
| exit: |
| return ret; |
| } |
| |
| static void rtl8723a_disabled_to_emu(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| |
| /* Clear suspend enable and power down enable*/ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 &= ~(BIT(3) | BIT(7)); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| |
| /* 0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/ |
| val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 2); |
| val8 &= ~BIT(0); |
| rtl8xxxu_write8(priv, REG_GPIO_INTM + 2, val8); |
| |
| /* 0x04[12:11] = 11 enable WL suspend*/ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 &= ~(BIT(3) | BIT(4)); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| } |
| |
| static void rtl8192e_disabled_to_emu(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| |
| /* Clear suspend enable and power down enable*/ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 &= ~(BIT(3) | BIT(4)); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| } |
| |
| static int rtl8192e_emu_to_active(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| u32 val32; |
| int count, ret = 0; |
| |
| /* disable HWPDN 0x04[15]=0*/ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 &= ~BIT(7); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| |
| /* disable SW LPS 0x04[10]= 0 */ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 &= ~BIT(2); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| |
| /* disable WL suspend*/ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 &= ~(BIT(3) | BIT(4)); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| |
| /* wait till 0x04[17] = 1 power ready*/ |
| for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| if (val32 & BIT(17)) |
| break; |
| |
| udelay(10); |
| } |
| |
| if (!count) { |
| ret = -EBUSY; |
| goto exit; |
| } |
| |
| /* We should be able to optimize the following three entries into one */ |
| |
| /* release WLON reset 0x04[16]= 1*/ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 2); |
| val8 |= BIT(0); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 2, val8); |
| |
| /* set, then poll until 0 */ |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| val32 |= APS_FSMCO_MAC_ENABLE; |
| rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); |
| |
| for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| if ((val32 & APS_FSMCO_MAC_ENABLE) == 0) { |
| ret = 0; |
| break; |
| } |
| udelay(10); |
| } |
| |
| if (!count) { |
| ret = -EBUSY; |
| goto exit; |
| } |
| |
| exit: |
| return ret; |
| } |
| |
| static int rtl8723a_emu_to_active(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| u32 val32; |
| int count, ret = 0; |
| |
| /* 0x20[0] = 1 enable LDOA12 MACRO block for all interface*/ |
| val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL); |
| val8 |= LDOA15_ENABLE; |
| rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8); |
| |
| /* 0x67[0] = 0 to disable BT_GPS_SEL pins*/ |
| val8 = rtl8xxxu_read8(priv, 0x0067); |
| val8 &= ~BIT(4); |
| rtl8xxxu_write8(priv, 0x0067, val8); |
| |
| mdelay(1); |
| |
| /* 0x00[5] = 0 release analog Ips to digital, 1:isolation */ |
| val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL); |
| val8 &= ~SYS_ISO_ANALOG_IPS; |
| rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8); |
| |
| /* disable SW LPS 0x04[10]= 0 */ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 &= ~BIT(2); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| |
| /* wait till 0x04[17] = 1 power ready*/ |
| for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| if (val32 & BIT(17)) |
| break; |
| |
| udelay(10); |
| } |
| |
| if (!count) { |
| ret = -EBUSY; |
| goto exit; |
| } |
| |
| /* We should be able to optimize the following three entries into one */ |
| |
| /* release WLON reset 0x04[16]= 1*/ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 2); |
| val8 |= BIT(0); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 2, val8); |
| |
| /* disable HWPDN 0x04[15]= 0*/ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 &= ~BIT(7); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| |
| /* disable WL suspend*/ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 &= ~(BIT(3) | BIT(4)); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| |
| /* set, then poll until 0 */ |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| val32 |= APS_FSMCO_MAC_ENABLE; |
| rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); |
| |
| for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| if ((val32 & APS_FSMCO_MAC_ENABLE) == 0) { |
| ret = 0; |
| break; |
| } |
| udelay(10); |
| } |
| |
| if (!count) { |
| ret = -EBUSY; |
| goto exit; |
| } |
| |
| /* 0x4C[23] = 0x4E[7] = 1, switch DPDT_SEL_P output from WL BB */ |
| /* |
| * Note: Vendor driver actually clears this bit, despite the |
| * documentation claims it's being set! |
| */ |
| val8 = rtl8xxxu_read8(priv, REG_LEDCFG2); |
| val8 |= LEDCFG2_DPDT_SELECT; |
| val8 &= ~LEDCFG2_DPDT_SELECT; |
| rtl8xxxu_write8(priv, REG_LEDCFG2, val8); |
| |
| exit: |
| return ret; |
| } |
| |
| static int rtl8723b_emu_to_active(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| u32 val32; |
| int count, ret = 0; |
| |
| /* 0x20[0] = 1 enable LDOA12 MACRO block for all interface */ |
| val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL); |
| val8 |= LDOA15_ENABLE; |
| rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8); |
| |
| /* 0x67[0] = 0 to disable BT_GPS_SEL pins*/ |
| val8 = rtl8xxxu_read8(priv, 0x0067); |
| val8 &= ~BIT(4); |
| rtl8xxxu_write8(priv, 0x0067, val8); |
| |
| mdelay(1); |
| |
| /* 0x00[5] = 0 release analog Ips to digital, 1:isolation */ |
| val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL); |
| val8 &= ~SYS_ISO_ANALOG_IPS; |
| rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8); |
| |
| /* Disable SW LPS 0x04[10]= 0 */ |
| val32 = rtl8xxxu_read8(priv, REG_APS_FSMCO); |
| val32 &= ~APS_FSMCO_SW_LPS; |
| rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); |
| |
| /* Wait until 0x04[17] = 1 power ready */ |
| for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| if (val32 & BIT(17)) |
| break; |
| |
| udelay(10); |
| } |
| |
| if (!count) { |
| ret = -EBUSY; |
| goto exit; |
| } |
| |
| /* We should be able to optimize the following three entries into one */ |
| |
| /* Release WLON reset 0x04[16]= 1*/ |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| val32 |= APS_FSMCO_WLON_RESET; |
| rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); |
| |
| /* Disable HWPDN 0x04[15]= 0*/ |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| val32 &= ~APS_FSMCO_HW_POWERDOWN; |
| rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); |
| |
| /* Disable WL suspend*/ |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| val32 &= ~(APS_FSMCO_HW_SUSPEND | APS_FSMCO_PCIE); |
| rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); |
| |
| /* Set, then poll until 0 */ |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| val32 |= APS_FSMCO_MAC_ENABLE; |
| rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); |
| |
| for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { |
| val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); |
| if ((val32 & APS_FSMCO_MAC_ENABLE) == 0) { |
| ret = 0; |
| break; |
| } |
| udelay(10); |
| } |
| |
| if (!count) { |
| ret = -EBUSY; |
| goto exit; |
| } |
| |
| /* Enable WL control XTAL setting */ |
| val8 = rtl8xxxu_read8(priv, REG_AFE_MISC); |
| val8 |= AFE_MISC_WL_XTAL_CTRL; |
| rtl8xxxu_write8(priv, REG_AFE_MISC, val8); |
| |
| /* Enable falling edge triggering interrupt */ |
| val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 1); |
| val8 |= BIT(1); |
| rtl8xxxu_write8(priv, REG_GPIO_INTM + 1, val8); |
| |
| /* Enable GPIO9 interrupt mode */ |
| val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2 + 1); |
| val8 |= BIT(1); |
| rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2 + 1, val8); |
| |
| /* Enable GPIO9 input mode */ |
| val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2); |
| val8 &= ~BIT(1); |
| rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2, val8); |
| |
| /* Enable HSISR GPIO[C:0] interrupt */ |
| val8 = rtl8xxxu_read8(priv, REG_HSIMR); |
| val8 |= BIT(0); |
| rtl8xxxu_write8(priv, REG_HSIMR, val8); |
| |
| /* Enable HSISR GPIO9 interrupt */ |
| val8 = rtl8xxxu_read8(priv, REG_HSIMR + 2); |
| val8 |= BIT(1); |
| rtl8xxxu_write8(priv, REG_HSIMR + 2, val8); |
| |
| val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL); |
| val8 |= MULTI_WIFI_HW_ROF_EN; |
| rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL, val8); |
| |
| /* For GPIO9 internal pull high setting BIT(14) */ |
| val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL + 1); |
| val8 |= BIT(6); |
| rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL + 1, val8); |
| |
| exit: |
| return ret; |
| } |
| |
| static int rtl8xxxu_emu_to_disabled(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| |
| /* 0x0007[7:0] = 0x20 SOP option to disable BG/MB */ |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 3, 0x20); |
| |
| /* 0x04[12:11] = 01 enable WL suspend */ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 &= ~BIT(4); |
| val8 |= BIT(3); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); |
| val8 |= BIT(7); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); |
| |
| /* 0x48[16] = 1 to enable GPIO9 as EXT wakeup */ |
| val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 2); |
| val8 |= BIT(0); |
| rtl8xxxu_write8(priv, REG_GPIO_INTM + 2, val8); |
| |
| return 0; |
| } |
| |
| static int rtl8723au_power_on(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| u16 val16; |
| u32 val32; |
| int ret; |
| |
| /* |
| * RSV_CTRL 0x001C[7:0] = 0x00, unlock ISO/CLK/Power control register |
| */ |
| rtl8xxxu_write8(priv, REG_RSV_CTRL, 0x0); |
| |
| rtl8723a_disabled_to_emu(priv); |
| |
| ret = rtl8723a_emu_to_active(priv); |
| if (ret) |
| goto exit; |
| |
| /* |
| * 0x0004[19] = 1, reset 8051 |
| */ |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 2); |
| val8 |= BIT(3); |
| rtl8xxxu_write8(priv, REG_APS_FSMCO + 2, val8); |
| |
| /* |
| * Enable MAC DMA/WMAC/SCHEDULE/SEC block |
| * Set CR bit10 to enable 32k calibration. |
| */ |
| val16 = rtl8xxxu_read16(priv, REG_CR); |
| val16 |= (CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE | |
| CR_TXDMA_ENABLE | CR_RXDMA_ENABLE | |
| CR_PROTOCOL_ENABLE | CR_SCHEDULE_ENABLE | |
| CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE | |
| CR_SECURITY_ENABLE | CR_CALTIMER_ENABLE); |
| rtl8xxxu_write16(priv, REG_CR, val16); |
| |
| /* For EFuse PG */ |
| val32 = rtl8xxxu_read32(priv, REG_EFUSE_CTRL); |
| val32 &= ~(BIT(28) | BIT(29) | BIT(30)); |
| val32 |= (0x06 << 28); |
| rtl8xxxu_write32(priv, REG_EFUSE_CTRL, val32); |
| exit: |
| return ret; |
| } |
| |
| static int rtl8723bu_power_on(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| u16 val16; |
| u32 val32; |
| int ret; |
| |
| rtl8723a_disabled_to_emu(priv); |
| |
| ret = rtl8723b_emu_to_active(priv); |
| if (ret) |
| goto exit; |
| |
| /* |
| * Enable MAC DMA/WMAC/SCHEDULE/SEC block |
| * Set CR bit10 to enable 32k calibration. |
| */ |
| val16 = rtl8xxxu_read16(priv, REG_CR); |
| val16 |= (CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE | |
| CR_TXDMA_ENABLE | CR_RXDMA_ENABLE | |
| CR_PROTOCOL_ENABLE | CR_SCHEDULE_ENABLE | |
| CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE | |
| CR_SECURITY_ENABLE | CR_CALTIMER_ENABLE); |
| rtl8xxxu_write16(priv, REG_CR, val16); |
| |
| /* |
| * BT coexist power on settings. This is identical for 1 and 2 |
| * antenna parts. |
| */ |
| rtl8xxxu_write8(priv, REG_PAD_CTRL1 + 3, 0x20); |
| |
| val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); |
| val16 |= SYS_FUNC_BBRSTB | SYS_FUNC_BB_GLB_RSTN; |
| rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); |
| |
| rtl8xxxu_write8(priv, REG_BT_CONTROL_8723BU + 1, 0x18); |
| rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04); |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00); |
| /* Antenna inverse */ |
| rtl8xxxu_write8(priv, 0xfe08, 0x01); |
| |
| val16 = rtl8xxxu_read16(priv, REG_PWR_DATA); |
| val16 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN; |
| rtl8xxxu_write16(priv, REG_PWR_DATA, val16); |
| |
| val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); |
| val32 |= LEDCFG0_DPDT_SELECT; |
| rtl8xxxu_write32(priv, REG_LEDCFG0, val32); |
| |
| val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1); |
| val8 &= ~PAD_CTRL1_SW_DPDT_SEL_DATA; |
| rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8); |
| exit: |
| return ret; |
| } |
| |
| #ifdef CONFIG_RTL8XXXU_UNTESTED |
| |
| static int rtl8192cu_power_on(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| u16 val16; |
| u32 val32; |
| int i; |
| |
| for (i = 100; i; i--) { |
| val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO); |
| if (val8 & APS_FSMCO_PFM_ALDN) |
| break; |
| } |
| |
| if (!i) { |
| pr_info("%s: Poll failed\n", __func__); |
| return -ENODEV; |
| } |
| |
| /* |
| * RSV_CTRL 0x001C[7:0] = 0x00, unlock ISO/CLK/Power control register |
| */ |
| rtl8xxxu_write8(priv, REG_RSV_CTRL, 0x0); |
| rtl8xxxu_write8(priv, REG_SPS0_CTRL, 0x2b); |
| udelay(100); |
| |
| val8 = rtl8xxxu_read8(priv, REG_LDOV12D_CTRL); |
| if (!(val8 & LDOV12D_ENABLE)) { |
| pr_info("%s: Enabling LDOV12D (%02x)\n", __func__, val8); |
| val8 |= LDOV12D_ENABLE; |
| rtl8xxxu_write8(priv, REG_LDOV12D_CTRL, val8); |
| |
| udelay(100); |
| |
| val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL); |
| val8 &= ~SYS_ISO_MD2PP; |
| rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8); |
| } |
| |
| /* |
| * Auto enable WLAN |
| */ |
| val16 = rtl8xxxu_read16(priv, REG_APS_FSMCO); |
| val16 |= APS_FSMCO_MAC_ENABLE; |
| rtl8xxxu_write16(priv, REG_APS_FSMCO, val16); |
| |
| for (i = 1000; i; i--) { |
| val16 = rtl8xxxu_read16(priv, REG_APS_FSMCO); |
| if (!(val16 & APS_FSMCO_MAC_ENABLE)) |
| break; |
| } |
| if (!i) { |
| pr_info("%s: FSMCO_MAC_ENABLE poll failed\n", __func__); |
| return -EBUSY; |
| } |
| |
| /* |
| * Enable radio, GPIO, LED |
| */ |
| val16 = APS_FSMCO_HW_SUSPEND | APS_FSMCO_ENABLE_POWERDOWN | |
| APS_FSMCO_PFM_ALDN; |
| rtl8xxxu_write16(priv, REG_APS_FSMCO, val16); |
| |
| /* |
| * Release RF digital isolation |
| */ |
| val16 = rtl8xxxu_read16(priv, REG_SYS_ISO_CTRL); |
| val16 &= ~SYS_ISO_DIOR; |
| rtl8xxxu_write16(priv, REG_SYS_ISO_CTRL, val16); |
| |
| val8 = rtl8xxxu_read8(priv, REG_APSD_CTRL); |
| val8 &= ~APSD_CTRL_OFF; |
| rtl8xxxu_write8(priv, REG_APSD_CTRL, val8); |
| for (i = 200; i; i--) { |
| val8 = rtl8xxxu_read8(priv, REG_APSD_CTRL); |
| if (!(val8 & APSD_CTRL_OFF_STATUS)) |
| break; |
| } |
| |
| if (!i) { |
| pr_info("%s: APSD_CTRL poll failed\n", __func__); |
| return -EBUSY; |
| } |
| |
| /* |
| * Enable MAC DMA/WMAC/SCHEDULE/SEC block |
| */ |
| val16 = rtl8xxxu_read16(priv, REG_CR); |
| val16 |= CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE | |
| CR_TXDMA_ENABLE | CR_RXDMA_ENABLE | CR_PROTOCOL_ENABLE | |
| CR_SCHEDULE_ENABLE | CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE; |
| rtl8xxxu_write16(priv, REG_CR, val16); |
| |
| /* |
| * Workaround for 8188RU LNA power leakage problem. |
| */ |
| if (priv->rtlchip == 0x8188c && priv->hi_pa) { |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_XCD_RF_PARM); |
| val32 &= ~BIT(1); |
| rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_PARM, val32); |
| } |
| return 0; |
| } |
| |
| #endif |
| |
| static int rtl8192eu_power_on(struct rtl8xxxu_priv *priv) |
| { |
| u16 val16; |
| u32 val32; |
| int ret; |
| |
| ret = 0; |
| |
| val32 = rtl8xxxu_read32(priv, REG_SYS_CFG); |
| if (val32 & SYS_CFG_SPS_LDO_SEL) { |
| rtl8xxxu_write8(priv, REG_LDO_SW_CTRL, 0xc3); |
| } else { |
| /* |
| * Raise 1.2V voltage |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_8192E_LDOV12_CTRL); |
| val32 &= 0xff0fffff; |
| val32 |= 0x00500000; |
| rtl8xxxu_write32(priv, REG_8192E_LDOV12_CTRL, val32); |
| rtl8xxxu_write8(priv, REG_LDO_SW_CTRL, 0x83); |
| } |
| |
| rtl8192e_disabled_to_emu(priv); |
| |
| ret = rtl8192e_emu_to_active(priv); |
| if (ret) |
| goto exit; |
| |
| rtl8xxxu_write16(priv, REG_CR, 0x0000); |
| |
| /* |
| * Enable MAC DMA/WMAC/SCHEDULE/SEC block |
| * Set CR bit10 to enable 32k calibration. |
| */ |
| val16 = rtl8xxxu_read16(priv, REG_CR); |
| val16 |= (CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE | |
| CR_TXDMA_ENABLE | CR_RXDMA_ENABLE | |
| CR_PROTOCOL_ENABLE | CR_SCHEDULE_ENABLE | |
| CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE | |
| CR_SECURITY_ENABLE | CR_CALTIMER_ENABLE); |
| rtl8xxxu_write16(priv, REG_CR, val16); |
| |
| exit: |
| return ret; |
| } |
| |
| static void rtl8xxxu_power_off(struct rtl8xxxu_priv *priv) |
| { |
| u8 val8; |
| u16 val16; |
| u32 val32; |
| |
| /* |
| * Workaround for 8188RU LNA power leakage problem. |
| */ |
| if (priv->rtlchip == 0x8188c && priv->hi_pa) { |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_XCD_RF_PARM); |
| val32 |= BIT(1); |
| rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_PARM, val32); |
| } |
| |
| rtl8xxxu_active_to_lps(priv); |
| |
| /* Turn off RF */ |
| rtl8xxxu_write8(priv, REG_RF_CTRL, 0x00); |
| |
| /* Reset Firmware if running in RAM */ |
| if (rtl8xxxu_read8(priv, REG_MCU_FW_DL) & MCU_FW_RAM_SEL) |
| rtl8xxxu_firmware_self_reset(priv); |
| |
| /* Reset MCU */ |
| val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); |
| val16 &= ~SYS_FUNC_CPU_ENABLE; |
| rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); |
| |
| /* Reset MCU ready status */ |
| rtl8xxxu_write8(priv, REG_MCU_FW_DL, 0x00); |
| |
| rtl8xxxu_active_to_emu(priv); |
| rtl8xxxu_emu_to_disabled(priv); |
| |
| /* Reset MCU IO Wrapper */ |
| val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1); |
| val8 &= ~BIT(0); |
| rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8); |
| |
| val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1); |
| val8 |= BIT(0); |
| rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8); |
| |
| /* RSV_CTRL 0x1C[7:0] = 0x0e lock ISO/CLK/Power control register */ |
| rtl8xxxu_write8(priv, REG_RSV_CTRL, 0x0e); |
| } |
| |
| #ifdef NEED_PS_TDMA |
| static void rtl8723bu_set_ps_tdma(struct rtl8xxxu_priv *priv, |
| u8 arg1, u8 arg2, u8 arg3, u8 arg4, u8 arg5) |
| { |
| struct h2c_cmd h2c; |
| |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| h2c.b_type_dma.cmd = H2C_8723B_B_TYPE_TDMA; |
| h2c.b_type_dma.data1 = arg1; |
| h2c.b_type_dma.data2 = arg2; |
| h2c.b_type_dma.data3 = arg3; |
| h2c.b_type_dma.data4 = arg4; |
| h2c.b_type_dma.data5 = arg5; |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.b_type_dma)); |
| } |
| #endif |
| |
| static void rtl8723bu_init_bt(struct rtl8xxxu_priv *priv) |
| { |
| struct h2c_cmd h2c; |
| u32 val32; |
| u8 val8; |
| |
| /* |
| * No indication anywhere as to what 0x0790 does. The 2 antenna |
| * vendor code preserves bits 6-7 here. |
| */ |
| rtl8xxxu_write8(priv, 0x0790, 0x05); |
| /* |
| * 0x0778 seems to be related to enabling the number of antennas |
| * In the vendor driver halbtc8723b2ant_InitHwConfig() sets it |
| * to 0x03, while halbtc8723b1ant_InitHwConfig() sets it to 0x01 |
| */ |
| rtl8xxxu_write8(priv, 0x0778, 0x01); |
| |
| val8 = rtl8xxxu_read8(priv, REG_GPIO_MUXCFG); |
| val8 |= BIT(5); |
| rtl8xxxu_write8(priv, REG_GPIO_MUXCFG, val8); |
| |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_IQADJ_G1, 0x780); |
| |
| rtl8723bu_write_btreg(priv, 0x3c, 0x15); /* BT TRx Mask on */ |
| |
| /* |
| * Set BT grant to low |
| */ |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| h2c.bt_grant.cmd = H2C_8723B_BT_GRANT; |
| h2c.bt_grant.data = 0; |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_grant)); |
| |
| /* |
| * WLAN action by PTA |
| */ |
| rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04); |
| |
| /* |
| * BT select S0/S1 controlled by WiFi |
| */ |
| val8 = rtl8xxxu_read8(priv, 0x0067); |
| val8 |= BIT(5); |
| rtl8xxxu_write8(priv, 0x0067, val8); |
| |
| val32 = rtl8xxxu_read32(priv, REG_PWR_DATA); |
| val32 |= BIT(11); |
| rtl8xxxu_write32(priv, REG_PWR_DATA, val32); |
| |
| /* |
| * Bits 6/7 are marked in/out ... but for what? |
| */ |
| rtl8xxxu_write8(priv, 0x0974, 0xff); |
| |
| val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER); |
| val32 |= (BIT(0) | BIT(1)); |
| rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32); |
| |
| rtl8xxxu_write8(priv, REG_RFE_CTRL_ANTA_SRC, 0x77); |
| |
| val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); |
| val32 &= ~BIT(24); |
| val32 |= BIT(23); |
| rtl8xxxu_write32(priv, REG_LEDCFG0, val32); |
| |
| /* |
| * Fix external switch Main->S1, Aux->S0 |
| */ |
| val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1); |
| val8 &= ~BIT(0); |
| rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8); |
| |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| h2c.ant_sel_rsv.cmd = H2C_8723B_ANT_SEL_RSV; |
| h2c.ant_sel_rsv.ant_inverse = 1; |
| h2c.ant_sel_rsv.int_switch_type = 0; |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.ant_sel_rsv)); |
| |
| /* |
| * 0x280, 0x00, 0x200, 0x80 - not clear |
| */ |
| rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00); |
| |
| /* |
| * Software control, antenna at WiFi side |
| */ |
| #ifdef NEED_PS_TDMA |
| rtl8723bu_set_ps_tdma(priv, 0x08, 0x00, 0x00, 0x00, 0x00); |
| #endif |
| |
| rtl8xxxu_write32(priv, REG_BT_COEX_TABLE1, 0x55555555); |
| rtl8xxxu_write32(priv, REG_BT_COEX_TABLE2, 0x55555555); |
| rtl8xxxu_write32(priv, REG_BT_COEX_TABLE3, 0x00ffffff); |
| rtl8xxxu_write8(priv, REG_BT_COEX_TABLE4, 0x03); |
| |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| h2c.bt_info.cmd = H2C_8723B_BT_INFO; |
| h2c.bt_info.data = BIT(0); |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_info)); |
| |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| h2c.ignore_wlan.cmd = H2C_8723B_BT_IGNORE_WLANACT; |
| h2c.ignore_wlan.data = 0; |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.ignore_wlan)); |
| } |
| |
| static void rtl8723bu_init_aggregation(struct rtl8xxxu_priv *priv) |
| { |
| u32 agg_rx; |
| u8 agg_ctrl; |
| |
| /* |
| * For now simply disable RX aggregation |
| */ |
| agg_ctrl = rtl8xxxu_read8(priv, REG_TRXDMA_CTRL); |
| agg_ctrl &= ~TRXDMA_CTRL_RXDMA_AGG_EN; |
| |
| agg_rx = rtl8xxxu_read32(priv, REG_RXDMA_AGG_PG_TH); |
| agg_rx &= ~RXDMA_USB_AGG_ENABLE; |
| agg_rx &= ~0xff0f; |
| |
| rtl8xxxu_write8(priv, REG_TRXDMA_CTRL, agg_ctrl); |
| rtl8xxxu_write32(priv, REG_RXDMA_AGG_PG_TH, agg_rx); |
| } |
| |
| static void rtl8723bu_init_statistics(struct rtl8xxxu_priv *priv) |
| { |
| u32 val32; |
| |
| /* Time duration for NHM unit: 4us, 0x2710=40ms */ |
| rtl8xxxu_write16(priv, REG_NHM_TIMER_8723B + 2, 0x2710); |
| rtl8xxxu_write16(priv, REG_NHM_TH9_TH10_8723B + 2, 0xffff); |
| rtl8xxxu_write32(priv, REG_NHM_TH3_TO_TH0_8723B, 0xffffff52); |
| rtl8xxxu_write32(priv, REG_NHM_TH7_TO_TH4_8723B, 0xffffffff); |
| /* TH8 */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); |
| val32 |= 0xff; |
| rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); |
| /* Enable CCK */ |
| val32 = rtl8xxxu_read32(priv, REG_NHM_TH9_TH10_8723B); |
| val32 |= BIT(8) | BIT(9) | BIT(10); |
| rtl8xxxu_write32(priv, REG_NHM_TH9_TH10_8723B, val32); |
| /* Max power amongst all RX antennas */ |
| val32 = rtl8xxxu_read32(priv, REG_OFDM0_FA_RSTC); |
| val32 |= BIT(7); |
| rtl8xxxu_write32(priv, REG_OFDM0_FA_RSTC, val32); |
| } |
| |
| static int rtl8xxxu_init_device(struct ieee80211_hw *hw) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| struct device *dev = &priv->udev->dev; |
| struct rtl8xxxu_rfregval *rftable; |
| bool macpower; |
| int ret; |
| u8 val8; |
| u16 val16; |
| u32 val32; |
| |
| /* Check if MAC is already powered on */ |
| val8 = rtl8xxxu_read8(priv, REG_CR); |
| |
| /* |
| * Fix 92DU-VC S3 hang with the reason is that secondary mac is not |
| * initialized. First MAC returns 0xea, second MAC returns 0x00 |
| */ |
| if (val8 == 0xea) |
| macpower = false; |
| else |
| macpower = true; |
| |
| ret = priv->fops->power_on(priv); |
| if (ret < 0) { |
| dev_warn(dev, "%s: Failed power on\n", __func__); |
| goto exit; |
| } |
| |
| dev_dbg(dev, "%s: macpower %i\n", __func__, macpower); |
| if (!macpower) { |
| ret = priv->fops->llt_init(priv, TX_TOTAL_PAGE_NUM); |
| if (ret) { |
| dev_warn(dev, "%s: LLT table init failed\n", __func__); |
| goto exit; |
| } |
| |
| /* |
| * Presumably this is for 8188EU as well |
| * Enable TX report and TX report timer |
| */ |
| if (priv->rtlchip == 0x8723bu) { |
| val8 = rtl8xxxu_read8(priv, REG_TX_REPORT_CTRL); |
| val8 |= BIT(1); |
| rtl8xxxu_write8(priv, REG_TX_REPORT_CTRL, val8); |
| /* Set MAX RPT MACID */ |
| rtl8xxxu_write8(priv, REG_TX_REPORT_CTRL + 1, 0x02); |
| /* TX report Timer. Unit: 32us */ |
| rtl8xxxu_write16(priv, REG_TX_REPORT_TIME, 0xcdf0); |
| |
| /* tmp ps ? */ |
| val8 = rtl8xxxu_read8(priv, 0xa3); |
| val8 &= 0xf8; |
| rtl8xxxu_write8(priv, 0xa3, val8); |
| } |
| } |
| |
| ret = rtl8xxxu_download_firmware(priv); |
| dev_dbg(dev, "%s: download_fiwmare %i\n", __func__, ret); |
| if (ret) |
| goto exit; |
| ret = rtl8xxxu_start_firmware(priv); |
| dev_dbg(dev, "%s: start_fiwmare %i\n", __func__, ret); |
| if (ret) |
| goto exit; |
| |
| /* Solve too many protocol error on USB bus */ |
| /* Can't do this for 8188/8192 UMC A cut parts */ |
| if (priv->rtlchip == 0x8723a || |
| ((priv->rtlchip == 0x8192c || priv->rtlchip == 0x8191c || |
| priv->rtlchip == 0x8188c) && |
| (priv->chip_cut || !priv->vendor_umc))) { |
| rtl8xxxu_write8(priv, 0xfe40, 0xe6); |
| rtl8xxxu_write8(priv, 0xfe41, 0x94); |
| rtl8xxxu_write8(priv, 0xfe42, 0x80); |
| |
| rtl8xxxu_write8(priv, 0xfe40, 0xe0); |
| rtl8xxxu_write8(priv, 0xfe41, 0x19); |
| rtl8xxxu_write8(priv, 0xfe42, 0x80); |
| |
| rtl8xxxu_write8(priv, 0xfe40, 0xe5); |
| rtl8xxxu_write8(priv, 0xfe41, 0x91); |
| rtl8xxxu_write8(priv, 0xfe42, 0x80); |
| |
| rtl8xxxu_write8(priv, 0xfe40, 0xe2); |
| rtl8xxxu_write8(priv, 0xfe41, 0x81); |
| rtl8xxxu_write8(priv, 0xfe42, 0x80); |
| } |
| |
| if (priv->rtlchip == 0x8192e) { |
| rtl8xxxu_write32(priv, REG_HIMR0, 0x00); |
| rtl8xxxu_write32(priv, REG_HIMR1, 0x00); |
| } |
| |
| if (priv->fops->phy_init_antenna_selection) |
| priv->fops->phy_init_antenna_selection(priv); |
| |
| if (priv->rtlchip == 0x8723b) |
| ret = rtl8xxxu_init_mac(priv, rtl8723b_mac_init_table); |
| else |
| ret = rtl8xxxu_init_mac(priv, rtl8723a_mac_init_table); |
| |
| dev_dbg(dev, "%s: init_mac %i\n", __func__, ret); |
| if (ret) |
| goto exit; |
| |
| ret = rtl8xxxu_init_phy_bb(priv); |
| dev_dbg(dev, "%s: init_phy_bb %i\n", __func__, ret); |
| if (ret) |
| goto exit; |
| |
| switch(priv->rtlchip) { |
| case 0x8723a: |
| rftable = rtl8723au_radioa_1t_init_table; |
| ret = rtl8xxxu_init_phy_rf(priv, rftable, RF_A); |
| break; |
| case 0x8723b: |
| rftable = rtl8723bu_radioa_1t_init_table; |
| ret = rtl8xxxu_init_phy_rf(priv, rftable, RF_A); |
| /* |
| * PHY LCK |
| */ |
| rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdfbe0); |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_MODE_AG, 0x8c01); |
| msleep(200); |
| rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdffe0); |
| break; |
| case 0x8188c: |
| if (priv->hi_pa) |
| rftable = rtl8188ru_radioa_1t_highpa_table; |
| else |
| rftable = rtl8192cu_radioa_1t_init_table; |
| ret = rtl8xxxu_init_phy_rf(priv, rftable, RF_A); |
| break; |
| case 0x8191c: |
| rftable = rtl8192cu_radioa_1t_init_table; |
| ret = rtl8xxxu_init_phy_rf(priv, rftable, RF_A); |
| break; |
| case 0x8192c: |
| rftable = rtl8192cu_radioa_2t_init_table; |
| ret = rtl8xxxu_init_phy_rf(priv, rftable, RF_A); |
| if (ret) |
| break; |
| rftable = rtl8192cu_radiob_2t_init_table; |
| ret = rtl8xxxu_init_phy_rf(priv, rftable, RF_B); |
| break; |
| default: |
| ret = -EINVAL; |
| } |
| |
| if (ret) |
| goto exit; |
| |
| /* |
| * Chip specific quirks |
| */ |
| if (priv->rtlchip == 0x8723a) { |
| /* Fix USB interface interference issue */ |
| rtl8xxxu_write8(priv, 0xfe40, 0xe0); |
| rtl8xxxu_write8(priv, 0xfe41, 0x8d); |
| rtl8xxxu_write8(priv, 0xfe42, 0x80); |
| rtl8xxxu_write32(priv, REG_TXDMA_OFFSET_CHK, 0xfd0320); |
| |
| /* Reduce 80M spur */ |
| rtl8xxxu_write32(priv, REG_AFE_XTAL_CTRL, 0x0381808d); |
| rtl8xxxu_write32(priv, REG_AFE_PLL_CTRL, 0xf0ffff83); |
| rtl8xxxu_write32(priv, REG_AFE_PLL_CTRL, 0xf0ffff82); |
| rtl8xxxu_write32(priv, REG_AFE_PLL_CTRL, 0xf0ffff83); |
| } else { |
| val32 = rtl8xxxu_read32(priv, REG_TXDMA_OFFSET_CHK); |
| val32 |= TXDMA_OFFSET_DROP_DATA_EN; |
| rtl8xxxu_write32(priv, REG_TXDMA_OFFSET_CHK, val32); |
| } |
| |
| if (!macpower) { |
| if (priv->ep_tx_normal_queue) |
| val8 = TX_PAGE_NUM_NORM_PQ; |
| else |
| val8 = 0; |
| |
| rtl8xxxu_write8(priv, REG_RQPN_NPQ, val8); |
| |
| val32 = (TX_PAGE_NUM_PUBQ << RQPN_NORM_PQ_SHIFT) | RQPN_LOAD; |
| |
| if (priv->ep_tx_high_queue) |
| val32 |= (TX_PAGE_NUM_HI_PQ << RQPN_HI_PQ_SHIFT); |
| if (priv->ep_tx_low_queue) |
| val32 |= (TX_PAGE_NUM_LO_PQ << RQPN_LO_PQ_SHIFT); |
| |
| rtl8xxxu_write32(priv, REG_RQPN, val32); |
| |
| /* |
| * Set TX buffer boundary |
| */ |
| val8 = TX_TOTAL_PAGE_NUM + 1; |
| |
| if (priv->rtlchip == 0x8723b) |
| val8 -= 1; |
| |
| rtl8xxxu_write8(priv, REG_TXPKTBUF_BCNQ_BDNY, val8); |
| rtl8xxxu_write8(priv, REG_TXPKTBUF_MGQ_BDNY, val8); |
| rtl8xxxu_write8(priv, REG_TXPKTBUF_WMAC_LBK_BF_HD, val8); |
| rtl8xxxu_write8(priv, REG_TRXFF_BNDY, val8); |
| rtl8xxxu_write8(priv, REG_TDECTRL + 1, val8); |
| } |
| |
| ret = rtl8xxxu_init_queue_priority(priv); |
| dev_dbg(dev, "%s: init_queue_priority %i\n", __func__, ret); |
| if (ret) |
| goto exit; |
| |
| /* RFSW Control - clear bit 14 ?? */ |
| if (priv->rtlchip != 0x8723b) |
| rtl8xxxu_write32(priv, REG_FPGA0_TX_INFO, 0x00000003); |
| /* 0x07000760 */ |
| val32 = FPGA0_RF_TRSW | FPGA0_RF_TRSWB | FPGA0_RF_ANTSW | |
| FPGA0_RF_ANTSWB | FPGA0_RF_PAPE | |
| ((FPGA0_RF_ANTSW | FPGA0_RF_ANTSWB | FPGA0_RF_PAPE) << |
| FPGA0_RF_BD_CTRL_SHIFT); |
| rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_SW_CTRL, val32); |
| /* 0x860[6:5]= 00 - why? - this sets antenna B */ |
| rtl8xxxu_write32(priv, REG_FPGA0_XA_RF_INT_OE, 0x66F60210); |
| |
| priv->rf_mode_ag[0] = rtl8xxxu_read_rfreg(priv, RF_A, |
| RF6052_REG_MODE_AG); |
| |
| /* |
| * Set RX page boundary |
| */ |
| if (priv->rtlchip == 0x8723b) |
| rtl8xxxu_write16(priv, REG_TRXFF_BNDY + 2, 0x3f7f); |
| else |
| rtl8xxxu_write16(priv, REG_TRXFF_BNDY + 2, 0x27ff); |
| /* |
| * Transfer page size is always 128 |
| */ |
| if (priv->rtlchip == 0x8723b) |
| val8 = (PBP_PAGE_SIZE_256 << PBP_PAGE_SIZE_RX_SHIFT) | |
| (PBP_PAGE_SIZE_256 << PBP_PAGE_SIZE_TX_SHIFT); |
| else |
| val8 = (PBP_PAGE_SIZE_128 << PBP_PAGE_SIZE_RX_SHIFT) | |
| (PBP_PAGE_SIZE_128 << PBP_PAGE_SIZE_TX_SHIFT); |
| rtl8xxxu_write8(priv, REG_PBP, val8); |
| |
| /* |
| * Unit in 8 bytes, not obvious what it is used for |
| */ |
| rtl8xxxu_write8(priv, REG_RX_DRVINFO_SZ, 4); |
| |
| /* |
| * Enable all interrupts - not obvious USB needs to do this |
| */ |
| rtl8xxxu_write32(priv, REG_HISR, 0xffffffff); |
| rtl8xxxu_write32(priv, REG_HIMR, 0xffffffff); |
| |
| rtl8xxxu_set_mac(priv); |
| rtl8xxxu_set_linktype(priv, NL80211_IFTYPE_STATION); |
| |
| /* |
| * Configure initial WMAC settings |
| */ |
| val32 = RCR_ACCEPT_PHYS_MATCH | RCR_ACCEPT_MCAST | RCR_ACCEPT_BCAST | |
| RCR_ACCEPT_MGMT_FRAME | RCR_HTC_LOC_CTRL | |
| RCR_APPEND_PHYSTAT | RCR_APPEND_ICV | RCR_APPEND_MIC; |
| rtl8xxxu_write32(priv, REG_RCR, val32); |
| |
| /* |
| * Accept all multicast |
| */ |
| rtl8xxxu_write32(priv, REG_MAR, 0xffffffff); |
| rtl8xxxu_write32(priv, REG_MAR + 4, 0xffffffff); |
| |
| /* |
| * Init adaptive controls |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_RESPONSE_RATE_SET); |
| val32 &= ~RESPONSE_RATE_BITMAP_ALL; |
| val32 |= RESPONSE_RATE_RRSR_CCK_ONLY_1M; |
| rtl8xxxu_write32(priv, REG_RESPONSE_RATE_SET, val32); |
| |
| /* CCK = 0x0a, OFDM = 0x10 */ |
| rtl8xxxu_set_spec_sifs(priv, 0x10, 0x10); |
| rtl8xxxu_set_retry(priv, 0x30, 0x30); |
| rtl8xxxu_set_spec_sifs(priv, 0x0a, 0x10); |
| |
| /* |
| * Init EDCA |
| */ |
| rtl8xxxu_write16(priv, REG_MAC_SPEC_SIFS, 0x100a); |
| |
| /* Set CCK SIFS */ |
| rtl8xxxu_write16(priv, REG_SIFS_CCK, 0x100a); |
| |
| /* Set OFDM SIFS */ |
| rtl8xxxu_write16(priv, REG_SIFS_OFDM, 0x100a); |
| |
| /* TXOP */ |
| rtl8xxxu_write32(priv, REG_EDCA_BE_PARAM, 0x005ea42b); |
| rtl8xxxu_write32(priv, REG_EDCA_BK_PARAM, 0x0000a44f); |
| rtl8xxxu_write32(priv, REG_EDCA_VI_PARAM, 0x005ea324); |
| rtl8xxxu_write32(priv, REG_EDCA_VO_PARAM, 0x002fa226); |
| |
| /* Set data auto rate fallback retry count */ |
| rtl8xxxu_write32(priv, REG_DARFRC, 0x00000000); |
| rtl8xxxu_write32(priv, REG_DARFRC + 4, 0x10080404); |
| rtl8xxxu_write32(priv, REG_RARFRC, 0x04030201); |
| rtl8xxxu_write32(priv, REG_RARFRC + 4, 0x08070605); |
| |
| val8 = rtl8xxxu_read8(priv, REG_FWHW_TXQ_CTRL); |
| val8 |= FWHW_TXQ_CTRL_AMPDU_RETRY; |
| rtl8xxxu_write8(priv, REG_FWHW_TXQ_CTRL, val8); |
| |
| /* Set ACK timeout */ |
| rtl8xxxu_write8(priv, REG_ACKTO, 0x40); |
| |
| /* |
| * Initialize beacon parameters |
| */ |
| val16 = BEACON_DISABLE_TSF_UPDATE | (BEACON_DISABLE_TSF_UPDATE << 8); |
| rtl8xxxu_write16(priv, REG_BEACON_CTRL, val16); |
| rtl8xxxu_write16(priv, REG_TBTT_PROHIBIT, 0x6404); |
| rtl8xxxu_write8(priv, REG_DRIVER_EARLY_INT, DRIVER_EARLY_INT_TIME); |
| rtl8xxxu_write8(priv, REG_BEACON_DMA_TIME, BEACON_DMA_ATIME_INT_TIME); |
| rtl8xxxu_write16(priv, REG_BEACON_TCFG, 0x660F); |
| |
| /* |
| * Initialize burst parameters |
| */ |
| if (priv->rtlchip == 0x8723b) { |
| /* |
| * For USB high speed set 512B packets |
| */ |
| val8 = rtl8xxxu_read8(priv, REG_RXDMA_PRO_8723B); |
| val8 &= ~(BIT(4) | BIT(5)); |
| val8 |= BIT(4); |
| val8 |= BIT(1) | BIT(2) | BIT(3); |
| rtl8xxxu_write8(priv, REG_RXDMA_PRO_8723B, val8); |
| |
| /* |
| * For USB high speed set 512B packets |
| */ |
| val8 = rtl8xxxu_read8(priv, REG_HT_SINGLE_AMPDU_8723B); |
| val8 |= BIT(7); |
| rtl8xxxu_write8(priv, REG_HT_SINGLE_AMPDU_8723B, val8); |
| |
| rtl8xxxu_write16(priv, REG_MAX_AGGR_NUM, 0x0c14); |
| rtl8xxxu_write8(priv, REG_AMPDU_MAX_TIME_8723B, 0x5e); |
| rtl8xxxu_write32(priv, REG_AGGLEN_LMT, 0xffffffff); |
| rtl8xxxu_write8(priv, REG_RX_PKT_LIMIT, 0x18); |
| rtl8xxxu_write8(priv, REG_PIFS, 0x00); |
| rtl8xxxu_write8(priv, REG_USTIME_TSF_8723B, 0x50); |
| rtl8xxxu_write8(priv, REG_USTIME_EDCA, 0x50); |
| |
| val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL); |
| val8 |= BIT(5) | BIT(6); |
| rtl8xxxu_write8(priv, REG_RSV_CTRL, val8); |
| } |
| |
| if (priv->fops->init_aggregation) |
| priv->fops->init_aggregation(priv); |
| |
| /* |
| * Enable CCK and OFDM block |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE); |
| val32 |= (FPGA_RF_MODE_CCK | FPGA_RF_MODE_OFDM); |
| rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32); |
| |
| /* |
| * Invalidate all CAM entries - bit 30 is undocumented |
| */ |
| rtl8xxxu_write32(priv, REG_CAM_CMD, CAM_CMD_POLLING | BIT(30)); |
| |
| /* |
| * Start out with default power levels for channel 6, 20MHz |
| */ |
| priv->fops->set_tx_power(priv, 1, false); |
| |
| /* Let the 8051 take control of antenna setting */ |
| val8 = rtl8xxxu_read8(priv, REG_LEDCFG2); |
| val8 |= LEDCFG2_DPDT_SELECT; |
| rtl8xxxu_write8(priv, REG_LEDCFG2, val8); |
| |
| rtl8xxxu_write8(priv, REG_HWSEQ_CTRL, 0xff); |
| |
| /* Disable BAR - not sure if this has any effect on USB */ |
| rtl8xxxu_write32(priv, REG_BAR_MODE_CTRL, 0x0201ffff); |
| |
| rtl8xxxu_write16(priv, REG_FAST_EDCA_CTRL, 0); |
| |
| if (priv->fops->init_statistics) |
| priv->fops->init_statistics(priv); |
| |
| rtl8723a_phy_lc_calibrate(priv); |
| |
| priv->fops->phy_iq_calibrate(priv); |
| |
| /* |
| * This should enable thermal meter |
| */ |
| if (priv->fops->has_s0s1) |
| rtl8xxxu_write_rfreg(priv, |
| RF_A, RF6052_REG_T_METER_8723B, 0x37cf8); |
| else |
| rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_T_METER, 0x60); |
| |
| /* Init BT hw config. */ |
| if (priv->fops->init_bt) |
| priv->fops->init_bt(priv); |
| |
| /* Set NAV_UPPER to 30000us */ |
| val8 = ((30000 + NAV_UPPER_UNIT - 1) / NAV_UPPER_UNIT); |
| rtl8xxxu_write8(priv, REG_NAV_UPPER, val8); |
| |
| if (priv->rtlchip == 0x8723a) { |
| /* |
| * 2011/03/09 MH debug only, UMC-B cut pass 2500 S5 test, |
| * but we need to find root cause. |
| * This is 8723au only. |
| */ |
| val32 = rtl8xxxu_read32(priv, REG_FPGA0_RF_MODE); |
| if ((val32 & 0xff000000) != 0x83000000) { |
| val32 |= FPGA_RF_MODE_CCK; |
| rtl8xxxu_write32(priv, REG_FPGA0_RF_MODE, val32); |
| } |
| } |
| |
| val32 = rtl8xxxu_read32(priv, REG_FWHW_TXQ_CTRL); |
| val32 |= FWHW_TXQ_CTRL_XMIT_MGMT_ACK; |
| /* ack for xmit mgmt frames. */ |
| rtl8xxxu_write32(priv, REG_FWHW_TXQ_CTRL, val32); |
| |
| exit: |
| return ret; |
| } |
| |
| static void rtl8xxxu_disable_device(struct ieee80211_hw *hw) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| |
| rtl8xxxu_power_off(priv); |
| } |
| |
| static void rtl8xxxu_cam_write(struct rtl8xxxu_priv *priv, |
| struct ieee80211_key_conf *key, const u8 *mac) |
| { |
| u32 cmd, val32, addr, ctrl; |
| int j, i, tmp_debug; |
| |
| tmp_debug = rtl8xxxu_debug; |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_KEY) |
| rtl8xxxu_debug |= RTL8XXXU_DEBUG_REG_WRITE; |
| |
| /* |
| * This is a bit of a hack - the lower bits of the cipher |
| * suite selector happens to match the cipher index in the CAM |
| */ |
| addr = key->keyidx << CAM_CMD_KEY_SHIFT; |
| ctrl = (key->cipher & 0x0f) << 2 | key->keyidx | CAM_WRITE_VALID; |
| |
| for (j = 5; j >= 0; j--) { |
| switch (j) { |
| case 0: |
| val32 = ctrl | (mac[0] << 16) | (mac[1] << 24); |
| break; |
| case 1: |
| val32 = mac[2] | (mac[3] << 8) | |
| (mac[4] << 16) | (mac[5] << 24); |
| break; |
| default: |
| i = (j - 2) << 2; |
| val32 = key->key[i] | (key->key[i + 1] << 8) | |
| key->key[i + 2] << 16 | key->key[i + 3] << 24; |
| break; |
| } |
| |
| rtl8xxxu_write32(priv, REG_CAM_WRITE, val32); |
| cmd = CAM_CMD_POLLING | CAM_CMD_WRITE | (addr + j); |
| rtl8xxxu_write32(priv, REG_CAM_CMD, cmd); |
| udelay(100); |
| } |
| |
| rtl8xxxu_debug = tmp_debug; |
| } |
| |
| static void rtl8xxxu_sw_scan_start(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, const u8 *mac) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| u8 val8; |
| |
| val8 = rtl8xxxu_read8(priv, REG_BEACON_CTRL); |
| val8 |= BEACON_DISABLE_TSF_UPDATE; |
| rtl8xxxu_write8(priv, REG_BEACON_CTRL, val8); |
| } |
| |
| static void rtl8xxxu_sw_scan_complete(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| u8 val8; |
| |
| val8 = rtl8xxxu_read8(priv, REG_BEACON_CTRL); |
| val8 &= ~BEACON_DISABLE_TSF_UPDATE; |
| rtl8xxxu_write8(priv, REG_BEACON_CTRL, val8); |
| } |
| |
| static void rtl8723au_update_rate_mask(struct rtl8xxxu_priv *priv, |
| u32 ramask, int sgi) |
| { |
| struct h2c_cmd h2c; |
| |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| |
| h2c.ramask.cmd = H2C_SET_RATE_MASK; |
| h2c.ramask.mask_lo = cpu_to_le16(ramask & 0xffff); |
| h2c.ramask.mask_hi = cpu_to_le16(ramask >> 16); |
| |
| h2c.ramask.arg = 0x80; |
| if (sgi) |
| h2c.ramask.arg |= 0x20; |
| |
| dev_dbg(&priv->udev->dev, "%s: rate mask %08x, arg %02x, size %zi\n", |
| __func__, ramask, h2c.ramask.arg, sizeof(h2c.ramask)); |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.ramask)); |
| } |
| |
| static void rtl8723bu_update_rate_mask(struct rtl8xxxu_priv *priv, |
| u32 ramask, int sgi) |
| { |
| struct h2c_cmd h2c; |
| u8 bw = 0; |
| |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| |
| h2c.b_macid_cfg.cmd = H2C_8723B_MACID_CFG_RAID; |
| h2c.b_macid_cfg.ramask0 = ramask & 0xff; |
| h2c.b_macid_cfg.ramask1 = (ramask >> 8) & 0xff; |
| h2c.b_macid_cfg.ramask2 = (ramask >> 16) & 0xff; |
| h2c.b_macid_cfg.ramask3 = (ramask >> 24) & 0xff; |
| |
| h2c.ramask.arg = 0x80; |
| h2c.b_macid_cfg.data1 = 0; |
| if (sgi) |
| h2c.b_macid_cfg.data1 |= BIT(7); |
| |
| h2c.b_macid_cfg.data2 = bw; |
| |
| dev_dbg(&priv->udev->dev, "%s: rate mask %08x, arg %02x, size %zi\n", |
| __func__, ramask, h2c.ramask.arg, sizeof(h2c.b_macid_cfg)); |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.b_macid_cfg)); |
| } |
| |
| static void rtl8723au_report_connect(struct rtl8xxxu_priv *priv, |
| u8 macid, bool connect) |
| { |
| struct h2c_cmd h2c; |
| |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| |
| h2c.joinbss.cmd = H2C_JOIN_BSS_REPORT; |
| |
| if (connect) |
| h2c.joinbss.data = H2C_JOIN_BSS_CONNECT; |
| else |
| h2c.joinbss.data = H2C_JOIN_BSS_DISCONNECT; |
| |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.joinbss)); |
| } |
| |
| static void rtl8723bu_report_connect(struct rtl8xxxu_priv *priv, |
| u8 macid, bool connect) |
| { |
| struct h2c_cmd h2c; |
| |
| memset(&h2c, 0, sizeof(struct h2c_cmd)); |
| |
| h2c.media_status_rpt.cmd = H2C_8723B_MEDIA_STATUS_RPT; |
| if (connect) |
| h2c.media_status_rpt.parm |= BIT(0); |
| else |
| h2c.media_status_rpt.parm &= ~BIT(0); |
| |
| rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.media_status_rpt)); |
| } |
| |
| static void rtl8xxxu_set_basic_rates(struct rtl8xxxu_priv *priv, u32 rate_cfg) |
| { |
| u32 val32; |
| u8 rate_idx = 0; |
| |
| rate_cfg &= RESPONSE_RATE_BITMAP_ALL; |
| |
| val32 = rtl8xxxu_read32(priv, REG_RESPONSE_RATE_SET); |
| val32 &= ~RESPONSE_RATE_BITMAP_ALL; |
| val32 |= rate_cfg; |
| rtl8xxxu_write32(priv, REG_RESPONSE_RATE_SET, val32); |
| |
| dev_dbg(&priv->udev->dev, "%s: rates %08x\n", __func__, rate_cfg); |
| |
| while (rate_cfg) { |
| rate_cfg = (rate_cfg >> 1); |
| rate_idx++; |
| } |
| rtl8xxxu_write8(priv, REG_INIRTS_RATE_SEL, rate_idx); |
| } |
| |
| static void |
| rtl8xxxu_bss_info_changed(struct ieee80211_hw *hw, struct ieee80211_vif *vif, |
| struct ieee80211_bss_conf *bss_conf, u32 changed) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| struct device *dev = &priv->udev->dev; |
| struct ieee80211_sta *sta; |
| u32 val32; |
| u8 val8; |
| |
| if (changed & BSS_CHANGED_ASSOC) { |
| dev_dbg(dev, "Changed ASSOC: %i!\n", bss_conf->assoc); |
| |
| rtl8xxxu_set_linktype(priv, vif->type); |
| |
| if (bss_conf->assoc) { |
| u32 ramask; |
| int sgi = 0; |
| |
| rcu_read_lock(); |
| sta = ieee80211_find_sta(vif, bss_conf->bssid); |
| if (!sta) { |
| dev_info(dev, "%s: ASSOC no sta found\n", |
| __func__); |
| rcu_read_unlock(); |
| goto error; |
| } |
| |
| if (sta->ht_cap.ht_supported) |
| dev_info(dev, "%s: HT supported\n", __func__); |
| if (sta->vht_cap.vht_supported) |
| dev_info(dev, "%s: VHT supported\n", __func__); |
| |
| /* TODO: Set bits 28-31 for rate adaptive id */ |
| ramask = (sta->supp_rates[0] & 0xfff) | |
| sta->ht_cap.mcs.rx_mask[0] << 12 | |
| sta->ht_cap.mcs.rx_mask[1] << 20; |
| if (sta->ht_cap.cap & |
| (IEEE80211_HT_CAP_SGI_40 | IEEE80211_HT_CAP_SGI_20)) |
| sgi = 1; |
| rcu_read_unlock(); |
| |
| priv->fops->update_rate_mask(priv, ramask, sgi); |
| |
| rtl8xxxu_write8(priv, REG_BCN_MAX_ERR, 0xff); |
| |
| rtl8723a_stop_tx_beacon(priv); |
| |
| /* joinbss sequence */ |
| rtl8xxxu_write16(priv, REG_BCN_PSR_RPT, |
| 0xc000 | bss_conf->aid); |
| |
| priv->fops->report_connect(priv, 0, true); |
| } else { |
| val8 = rtl8xxxu_read8(priv, REG_BEACON_CTRL); |
| val8 |= BEACON_DISABLE_TSF_UPDATE; |
| rtl8xxxu_write8(priv, REG_BEACON_CTRL, val8); |
| |
| priv->fops->report_connect(priv, 0, false); |
| } |
| } |
| |
| if (changed & BSS_CHANGED_ERP_PREAMBLE) { |
| dev_dbg(dev, "Changed ERP_PREAMBLE: Use short preamble %i\n", |
| bss_conf->use_short_preamble); |
| val32 = rtl8xxxu_read32(priv, REG_RESPONSE_RATE_SET); |
| if (bss_conf->use_short_preamble) |
| val32 |= RSR_ACK_SHORT_PREAMBLE; |
| else |
| val32 &= ~RSR_ACK_SHORT_PREAMBLE; |
| rtl8xxxu_write32(priv, REG_RESPONSE_RATE_SET, val32); |
| } |
| |
| if (changed & BSS_CHANGED_ERP_SLOT) { |
| dev_dbg(dev, "Changed ERP_SLOT: short_slot_time %i\n", |
| bss_conf->use_short_slot); |
| |
| if (bss_conf->use_short_slot) |
| val8 = 9; |
| else |
| val8 = 20; |
| rtl8xxxu_write8(priv, REG_SLOT, val8); |
| } |
| |
| if (changed & BSS_CHANGED_BSSID) { |
| dev_dbg(dev, "Changed BSSID!\n"); |
| rtl8xxxu_set_bssid(priv, bss_conf->bssid); |
| } |
| |
| if (changed & BSS_CHANGED_BASIC_RATES) { |
| dev_dbg(dev, "Changed BASIC_RATES!\n"); |
| rtl8xxxu_set_basic_rates(priv, bss_conf->basic_rates); |
| } |
| error: |
| return; |
| } |
| |
| static u32 rtl8xxxu_80211_to_rtl_queue(u32 queue) |
| { |
| u32 rtlqueue; |
| |
| switch (queue) { |
| case IEEE80211_AC_VO: |
| rtlqueue = TXDESC_QUEUE_VO; |
| break; |
| case IEEE80211_AC_VI: |
| rtlqueue = TXDESC_QUEUE_VI; |
| break; |
| case IEEE80211_AC_BE: |
| rtlqueue = TXDESC_QUEUE_BE; |
| break; |
| case IEEE80211_AC_BK: |
| rtlqueue = TXDESC_QUEUE_BK; |
| break; |
| default: |
| rtlqueue = TXDESC_QUEUE_BE; |
| } |
| |
| return rtlqueue; |
| } |
| |
| static u32 rtl8xxxu_queue_select(struct ieee80211_hw *hw, struct sk_buff *skb) |
| { |
| struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; |
| u32 queue; |
| |
| if (ieee80211_is_mgmt(hdr->frame_control)) |
| queue = TXDESC_QUEUE_MGNT; |
| else |
| queue = rtl8xxxu_80211_to_rtl_queue(skb_get_queue_mapping(skb)); |
| |
| return queue; |
| } |
| |
| /* |
| * Despite newer chips 8723b/8812/8821 having a larger TX descriptor |
| * format. The descriptor checksum is still only calculated over the |
| * initial 32 bytes of the descriptor! |
| */ |
| static void rtl8xxxu_calc_tx_desc_csum(struct rtl8723au_tx_desc *tx_desc) |
| { |
| __le16 *ptr = (__le16 *)tx_desc; |
| u16 csum = 0; |
| int i; |
| |
| /* |
| * Clear csum field before calculation, as the csum field is |
| * in the middle of the struct. |
| */ |
| tx_desc->csum = cpu_to_le16(0); |
| |
| for (i = 0; i < (sizeof(struct rtl8723au_tx_desc) / sizeof(u16)); i++) |
| csum = csum ^ le16_to_cpu(ptr[i]); |
| |
| tx_desc->csum |= cpu_to_le16(csum); |
| } |
| |
| static void rtl8xxxu_free_tx_resources(struct rtl8xxxu_priv *priv) |
| { |
| struct rtl8xxxu_tx_urb *tx_urb, *tmp; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&priv->tx_urb_lock, flags); |
| list_for_each_entry_safe(tx_urb, tmp, &priv->tx_urb_free_list, list) { |
| list_del(&tx_urb->list); |
| priv->tx_urb_free_count--; |
| usb_free_urb(&tx_urb->urb); |
| } |
| spin_unlock_irqrestore(&priv->tx_urb_lock, flags); |
| } |
| |
| static struct rtl8xxxu_tx_urb * |
| rtl8xxxu_alloc_tx_urb(struct rtl8xxxu_priv *priv) |
| { |
| struct rtl8xxxu_tx_urb *tx_urb; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&priv->tx_urb_lock, flags); |
| tx_urb = list_first_entry_or_null(&priv->tx_urb_free_list, |
| struct rtl8xxxu_tx_urb, list); |
| if (tx_urb) { |
| list_del(&tx_urb->list); |
| priv->tx_urb_free_count--; |
| if (priv->tx_urb_free_count < RTL8XXXU_TX_URB_LOW_WATER && |
| !priv->tx_stopped) { |
| priv->tx_stopped = true; |
| ieee80211_stop_queues(priv->hw); |
| } |
| } |
| |
| spin_unlock_irqrestore(&priv->tx_urb_lock, flags); |
| |
| return tx_urb; |
| } |
| |
| static void rtl8xxxu_free_tx_urb(struct rtl8xxxu_priv *priv, |
| struct rtl8xxxu_tx_urb *tx_urb) |
| { |
| unsigned long flags; |
| |
| INIT_LIST_HEAD(&tx_urb->list); |
| |
| spin_lock_irqsave(&priv->tx_urb_lock, flags); |
| |
| list_add(&tx_urb->list, &priv->tx_urb_free_list); |
| priv->tx_urb_free_count++; |
| if (priv->tx_urb_free_count > RTL8XXXU_TX_URB_HIGH_WATER && |
| priv->tx_stopped) { |
| priv->tx_stopped = false; |
| ieee80211_wake_queues(priv->hw); |
| } |
| |
| spin_unlock_irqrestore(&priv->tx_urb_lock, flags); |
| } |
| |
| static void rtl8xxxu_tx_complete(struct urb *urb) |
| { |
| struct sk_buff *skb = (struct sk_buff *)urb->context; |
| struct ieee80211_tx_info *tx_info; |
| struct ieee80211_hw *hw; |
| struct rtl8xxxu_priv *priv; |
| struct rtl8xxxu_tx_urb *tx_urb = |
| container_of(urb, struct rtl8xxxu_tx_urb, urb); |
| |
| tx_info = IEEE80211_SKB_CB(skb); |
| hw = tx_info->rate_driver_data[0]; |
| priv = hw->priv; |
| |
| skb_pull(skb, priv->fops->tx_desc_size); |
| |
| ieee80211_tx_info_clear_status(tx_info); |
| tx_info->status.rates[0].idx = -1; |
| tx_info->status.rates[0].count = 0; |
| |
| if (!urb->status) |
| tx_info->flags |= IEEE80211_TX_STAT_ACK; |
| |
| ieee80211_tx_status_irqsafe(hw, skb); |
| |
| rtl8xxxu_free_tx_urb(priv, tx_urb); |
| } |
| |
| static void rtl8xxxu_dump_action(struct device *dev, |
| struct ieee80211_hdr *hdr) |
| { |
| struct ieee80211_mgmt *mgmt = (struct ieee80211_mgmt *)hdr; |
| u16 cap, timeout; |
| |
| if (!(rtl8xxxu_debug & RTL8XXXU_DEBUG_ACTION)) |
| return; |
| |
| switch (mgmt->u.action.u.addba_resp.action_code) { |
| case WLAN_ACTION_ADDBA_RESP: |
| cap = le16_to_cpu(mgmt->u.action.u.addba_resp.capab); |
| timeout = le16_to_cpu(mgmt->u.action.u.addba_resp.timeout); |
| dev_info(dev, "WLAN_ACTION_ADDBA_RESP: " |
| "timeout %i, tid %02x, buf_size %02x, policy %02x, " |
| "status %02x\n", |
| timeout, |
| (cap & IEEE80211_ADDBA_PARAM_TID_MASK) >> 2, |
| (cap & IEEE80211_ADDBA_PARAM_BUF_SIZE_MASK) >> 6, |
| (cap >> 1) & 0x1, |
| le16_to_cpu(mgmt->u.action.u.addba_resp.status)); |
| break; |
| case WLAN_ACTION_ADDBA_REQ: |
| cap = le16_to_cpu(mgmt->u.action.u.addba_req.capab); |
| timeout = le16_to_cpu(mgmt->u.action.u.addba_req.timeout); |
| dev_info(dev, "WLAN_ACTION_ADDBA_REQ: " |
| "timeout %i, tid %02x, buf_size %02x, policy %02x\n", |
| timeout, |
| (cap & IEEE80211_ADDBA_PARAM_TID_MASK) >> 2, |
| (cap & IEEE80211_ADDBA_PARAM_BUF_SIZE_MASK) >> 6, |
| (cap >> 1) & 0x1); |
| break; |
| default: |
| dev_info(dev, "action frame %02x\n", |
| mgmt->u.action.u.addba_resp.action_code); |
| break; |
| } |
| } |
| |
| static void rtl8xxxu_tx(struct ieee80211_hw *hw, |
| struct ieee80211_tx_control *control, |
| struct sk_buff *skb) |
| { |
| struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; |
| struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb); |
| struct ieee80211_rate *tx_rate = ieee80211_get_tx_rate(hw, tx_info); |
| struct rtl8xxxu_priv *priv = hw->priv; |
| struct rtl8723au_tx_desc *tx_desc; |
| struct rtl8723bu_tx_desc *tx_desc40; |
| struct rtl8xxxu_tx_urb *tx_urb; |
| struct ieee80211_sta *sta = NULL; |
| struct ieee80211_vif *vif = tx_info->control.vif; |
| struct device *dev = &priv->udev->dev; |
| u32 queue, rate; |
| u16 pktlen = skb->len; |
| u16 seq_number; |
| u16 rate_flag = tx_info->control.rates[0].flags; |
| int tx_desc_size = priv->fops->tx_desc_size; |
| int ret; |
| bool usedesc40, ampdu_enable; |
| |
| if (skb_headroom(skb) < tx_desc_size) { |
| dev_warn(dev, |
| "%s: Not enough headroom (%i) for tx descriptor\n", |
| __func__, skb_headroom(skb)); |
| goto error; |
| } |
| |
| if (unlikely(skb->len > (65535 - tx_desc_size))) { |
| dev_warn(dev, "%s: Trying to send over-sized skb (%i)\n", |
| __func__, skb->len); |
| goto error; |
| } |
| |
| tx_urb = rtl8xxxu_alloc_tx_urb(priv); |
| if (!tx_urb) { |
| dev_warn(dev, "%s: Unable to allocate tx urb\n", __func__); |
| goto error; |
| } |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_TX) |
| dev_info(dev, "%s: TX rate: %d (%d), pkt size %d\n", |
| __func__, tx_rate->bitrate, tx_rate->hw_value, pktlen); |
| |
| if (ieee80211_is_action(hdr->frame_control)) |
| rtl8xxxu_dump_action(dev, hdr); |
| |
| usedesc40 = (tx_desc_size == 40); |
| tx_info->rate_driver_data[0] = hw; |
| |
| if (control && control->sta) |
| sta = control->sta; |
| |
| tx_desc = (struct rtl8723au_tx_desc *)skb_push(skb, tx_desc_size); |
| |
| memset(tx_desc, 0, tx_desc_size); |
| tx_desc->pkt_size = cpu_to_le16(pktlen); |
| tx_desc->pkt_offset = tx_desc_size; |
| |
| tx_desc->txdw0 = |
| TXDESC_OWN | TXDESC_FIRST_SEGMENT | TXDESC_LAST_SEGMENT; |
| if (is_multicast_ether_addr(ieee80211_get_DA(hdr)) || |
| is_broadcast_ether_addr(ieee80211_get_DA(hdr))) |
| tx_desc->txdw0 |= TXDESC_BROADMULTICAST; |
| |
| queue = rtl8xxxu_queue_select(hw, skb); |
| tx_desc->txdw1 = cpu_to_le32(queue << TXDESC_QUEUE_SHIFT); |
| |
| if (tx_info->control.hw_key) { |
| switch (tx_info->control.hw_key->cipher) { |
| case WLAN_CIPHER_SUITE_WEP40: |
| case WLAN_CIPHER_SUITE_WEP104: |
| case WLAN_CIPHER_SUITE_TKIP: |
| tx_desc->txdw1 |= cpu_to_le32(TXDESC_SEC_RC4); |
| break; |
| case WLAN_CIPHER_SUITE_CCMP: |
| tx_desc->txdw1 |= cpu_to_le32(TXDESC_SEC_AES); |
| break; |
| default: |
| break; |
| } |
| } |
| |
| /* (tx_info->flags & IEEE80211_TX_CTL_AMPDU) && */ |
| ampdu_enable = false; |
| if (ieee80211_is_data_qos(hdr->frame_control) && sta) { |
| if (sta->ht_cap.ht_supported) { |
| u32 ampdu, val32; |
| |
| ampdu = (u32)sta->ht_cap.ampdu_density; |
| val32 = ampdu << TXDESC_AMPDU_DENSITY_SHIFT; |
| tx_desc->txdw2 |= cpu_to_le32(val32); |
| |
| ampdu_enable = true; |
| } |
| } |
| |
| if (rate_flag & IEEE80211_TX_RC_MCS) |
| rate = tx_info->control.rates[0].idx + DESC_RATE_MCS0; |
| else |
| rate = tx_rate->hw_value; |
| |
| seq_number = IEEE80211_SEQ_TO_SN(le16_to_cpu(hdr->seq_ctrl)); |
| if (!usedesc40) { |
| tx_desc->txdw5 = cpu_to_le32(rate); |
| |
| if (ieee80211_is_data(hdr->frame_control)) |
| tx_desc->txdw5 |= cpu_to_le32(0x0001ff00); |
| |
| tx_desc->txdw3 = |
| cpu_to_le32((u32)seq_number << TXDESC_SEQ_SHIFT_8723A); |
| |
| if (ampdu_enable) |
| tx_desc->txdw1 |= cpu_to_le32(TXDESC_AGG_ENABLE_8723A); |
| else |
| tx_desc->txdw1 |= cpu_to_le32(TXDESC_AGG_BREAK_8723A); |
| |
| if (ieee80211_is_mgmt(hdr->frame_control)) { |
| tx_desc->txdw5 = cpu_to_le32(tx_rate->hw_value); |
| tx_desc->txdw4 |= |
| cpu_to_le32(TXDESC_USE_DRIVER_RATE_8723A); |
| tx_desc->txdw5 |= |
| cpu_to_le32(6 << |
| TXDESC_RETRY_LIMIT_SHIFT_8723A); |
| tx_desc->txdw5 |= |
| cpu_to_le32(TXDESC_RETRY_LIMIT_ENABLE_8723A); |
| } |
| |
| if (ieee80211_is_data_qos(hdr->frame_control)) |
| tx_desc->txdw4 |= cpu_to_le32(TXDESC_QOS_8723A); |
| |
| if (rate_flag & IEEE80211_TX_RC_USE_SHORT_PREAMBLE || |
| (sta && vif && vif->bss_conf.use_short_preamble)) |
| tx_desc->txdw4 |= |
| cpu_to_le32(TXDESC_SHORT_PREAMBLE_8723A); |
| |
| if (rate_flag & IEEE80211_TX_RC_SHORT_GI || |
| (ieee80211_is_data_qos(hdr->frame_control) && |
| sta && sta->ht_cap.cap & |
| (IEEE80211_HT_CAP_SGI_40 | IEEE80211_HT_CAP_SGI_20))) { |
| tx_desc->txdw5 |= cpu_to_le32(TXDESC_SHORT_GI); |
| } |
| |
| if (rate_flag & IEEE80211_TX_RC_USE_RTS_CTS) { |
| /* |
| * Use RTS rate 24M - does the mac80211 tell |
| * us which to use? |
| */ |
| tx_desc->txdw4 |= |
| cpu_to_le32(DESC_RATE_24M << |
| TXDESC_RTS_RATE_SHIFT_8723A); |
| tx_desc->txdw4 |= |
| cpu_to_le32(TXDESC_RTS_CTS_ENABLE_8723A); |
| tx_desc->txdw4 |= |
| cpu_to_le32(TXDESC_HW_RTS_ENABLE_8723A); |
| } |
| } else { |
| tx_desc40 = (struct rtl8723bu_tx_desc *)tx_desc; |
| |
| tx_desc40->txdw4 = cpu_to_le32(rate); |
| if (ieee80211_is_data(hdr->frame_control)) { |
| tx_desc->txdw4 |= |
| cpu_to_le32(0x1f << |
| TXDESC_DATA_RATE_FB_SHIFT_8723B); |
| } |
| |
| tx_desc40->txdw9 = |
| cpu_to_le32((u32)seq_number << TXDESC_SEQ_SHIFT_8723B); |
| |
| if (ampdu_enable) |
| tx_desc40->txdw2 |= |
| cpu_to_le32(TXDESC_AGG_ENABLE_8723B); |
| else |
| tx_desc40->txdw2 |= cpu_to_le32(TXDESC_AGG_BREAK_8723B); |
| |
| if (ieee80211_is_mgmt(hdr->frame_control)) { |
| tx_desc40->txdw4 = cpu_to_le32(tx_rate->hw_value); |
| tx_desc40->txdw3 |= |
| cpu_to_le32(TXDESC_USE_DRIVER_RATE_8723B); |
| tx_desc40->txdw4 |= |
| cpu_to_le32(6 << |
| TXDESC_RETRY_LIMIT_SHIFT_8723B); |
| tx_desc40->txdw4 |= |
| cpu_to_le32(TXDESC_RETRY_LIMIT_ENABLE_8723B); |
| } |
| |
| if (rate_flag & IEEE80211_TX_RC_USE_SHORT_PREAMBLE || |
| (sta && vif && vif->bss_conf.use_short_preamble)) |
| tx_desc40->txdw5 |= |
| cpu_to_le32(TXDESC_SHORT_PREAMBLE_8723B); |
| |
| if (rate_flag & IEEE80211_TX_RC_USE_RTS_CTS) { |
| /* |
| * Use RTS rate 24M - does the mac80211 tell |
| * us which to use? |
| */ |
| tx_desc->txdw4 |= |
| cpu_to_le32(DESC_RATE_24M << |
| TXDESC_RTS_RATE_SHIFT_8723B); |
| tx_desc->txdw3 |= |
| cpu_to_le32(TXDESC_RTS_CTS_ENABLE_8723B); |
| tx_desc->txdw3 |= |
| cpu_to_le32(TXDESC_HW_RTS_ENABLE_8723B); |
| } |
| }; |
| |
| rtl8xxxu_calc_tx_desc_csum(tx_desc); |
| |
| usb_fill_bulk_urb(&tx_urb->urb, priv->udev, priv->pipe_out[queue], |
| skb->data, skb->len, rtl8xxxu_tx_complete, skb); |
| |
| usb_anchor_urb(&tx_urb->urb, &priv->tx_anchor); |
| ret = usb_submit_urb(&tx_urb->urb, GFP_ATOMIC); |
| if (ret) { |
| usb_unanchor_urb(&tx_urb->urb); |
| rtl8xxxu_free_tx_urb(priv, tx_urb); |
| goto error; |
| } |
| return; |
| error: |
| dev_kfree_skb(skb); |
| } |
| |
| static void rtl8xxxu_rx_parse_phystats(struct rtl8xxxu_priv *priv, |
| struct ieee80211_rx_status *rx_status, |
| struct rtl8723au_phy_stats *phy_stats, |
| u32 rxmcs) |
| { |
| if (phy_stats->sgi_en) |
| rx_status->flag |= RX_FLAG_SHORT_GI; |
| |
| if (rxmcs < DESC_RATE_6M) { |
| /* |
| * Handle PHY stats for CCK rates |
| */ |
| u8 cck_agc_rpt = phy_stats->cck_agc_rpt_ofdm_cfosho_a; |
| |
| switch (cck_agc_rpt & 0xc0) { |
| case 0xc0: |
| rx_status->signal = -46 - (cck_agc_rpt & 0x3e); |
| break; |
| case 0x80: |
| rx_status->signal = -26 - (cck_agc_rpt & 0x3e); |
| break; |
| case 0x40: |
| rx_status->signal = -12 - (cck_agc_rpt & 0x3e); |
| break; |
| case 0x00: |
| rx_status->signal = 16 - (cck_agc_rpt & 0x3e); |
| break; |
| } |
| } else { |
| rx_status->signal = |
| (phy_stats->cck_sig_qual_ofdm_pwdb_all >> 1) - 110; |
| } |
| } |
| |
| static void rtl8xxxu_free_rx_resources(struct rtl8xxxu_priv *priv) |
| { |
| struct rtl8xxxu_rx_urb *rx_urb, *tmp; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&priv->rx_urb_lock, flags); |
| |
| list_for_each_entry_safe(rx_urb, tmp, |
| &priv->rx_urb_pending_list, list) { |
| list_del(&rx_urb->list); |
| priv->rx_urb_pending_count--; |
| usb_free_urb(&rx_urb->urb); |
| } |
| |
| spin_unlock_irqrestore(&priv->rx_urb_lock, flags); |
| } |
| |
| static void rtl8xxxu_queue_rx_urb(struct rtl8xxxu_priv *priv, |
| struct rtl8xxxu_rx_urb *rx_urb) |
| { |
| struct sk_buff *skb; |
| unsigned long flags; |
| int pending = 0; |
| |
| spin_lock_irqsave(&priv->rx_urb_lock, flags); |
| |
| if (!priv->shutdown) { |
| list_add_tail(&rx_urb->list, &priv->rx_urb_pending_list); |
| priv->rx_urb_pending_count++; |
| pending = priv->rx_urb_pending_count; |
| } else { |
| skb = (struct sk_buff *)rx_urb->urb.context; |
| dev_kfree_skb(skb); |
| usb_free_urb(&rx_urb->urb); |
| } |
| |
| spin_unlock_irqrestore(&priv->rx_urb_lock, flags); |
| |
| if (pending > RTL8XXXU_RX_URB_PENDING_WATER) |
| schedule_work(&priv->rx_urb_wq); |
| } |
| |
| static void rtl8xxxu_rx_urb_work(struct work_struct *work) |
| { |
| struct rtl8xxxu_priv *priv; |
| struct rtl8xxxu_rx_urb *rx_urb, *tmp; |
| struct list_head local; |
| struct sk_buff *skb; |
| unsigned long flags; |
| int ret; |
| |
| priv = container_of(work, struct rtl8xxxu_priv, rx_urb_wq); |
| INIT_LIST_HEAD(&local); |
| |
| spin_lock_irqsave(&priv->rx_urb_lock, flags); |
| |
| list_splice_init(&priv->rx_urb_pending_list, &local); |
| priv->rx_urb_pending_count = 0; |
| |
| spin_unlock_irqrestore(&priv->rx_urb_lock, flags); |
| |
| list_for_each_entry_safe(rx_urb, tmp, &local, list) { |
| list_del_init(&rx_urb->list); |
| ret = rtl8xxxu_submit_rx_urb(priv, rx_urb); |
| /* |
| * If out of memory or temporary error, put it back on the |
| * queue and try again. Otherwise the device is dead/gone |
| * and we should drop it. |
| */ |
| switch (ret) { |
| case 0: |
| break; |
| case -ENOMEM: |
| case -EAGAIN: |
| rtl8xxxu_queue_rx_urb(priv, rx_urb); |
| break; |
| default: |
| pr_info("failed to requeue urb %i\n", ret); |
| skb = (struct sk_buff *)rx_urb->urb.context; |
| dev_kfree_skb(skb); |
| usb_free_urb(&rx_urb->urb); |
| } |
| } |
| } |
| |
| static int rtl8723au_parse_rx_desc(struct rtl8xxxu_priv *priv, |
| struct sk_buff *skb, |
| struct ieee80211_rx_status *rx_status) |
| { |
| struct rtl8xxxu_rx_desc *rx_desc = (struct rtl8xxxu_rx_desc *)skb->data; |
| struct rtl8723au_phy_stats *phy_stats; |
| int drvinfo_sz, desc_shift; |
| |
| skb_pull(skb, sizeof(struct rtl8xxxu_rx_desc)); |
| |
| phy_stats = (struct rtl8723au_phy_stats *)skb->data; |
| |
| drvinfo_sz = rx_desc->drvinfo_sz * 8; |
| desc_shift = rx_desc->shift; |
| skb_pull(skb, drvinfo_sz + desc_shift); |
| |
| if (rx_desc->phy_stats) |
| rtl8xxxu_rx_parse_phystats(priv, rx_status, phy_stats, |
| rx_desc->rxmcs); |
| |
| rx_status->mactime = le32_to_cpu(rx_desc->tsfl); |
| rx_status->flag |= RX_FLAG_MACTIME_START; |
| |
| if (!rx_desc->swdec) |
| rx_status->flag |= RX_FLAG_DECRYPTED; |
| if (rx_desc->crc32) |
| rx_status->flag |= RX_FLAG_FAILED_FCS_CRC; |
| if (rx_desc->bw) |
| rx_status->flag |= RX_FLAG_40MHZ; |
| |
| if (rx_desc->rxht) { |
| rx_status->flag |= RX_FLAG_HT; |
| rx_status->rate_idx = rx_desc->rxmcs - DESC_RATE_MCS0; |
| } else { |
| rx_status->rate_idx = rx_desc->rxmcs; |
| } |
| |
| return RX_TYPE_DATA_PKT; |
| } |
| |
| static int rtl8723bu_parse_rx_desc(struct rtl8xxxu_priv *priv, |
| struct sk_buff *skb, |
| struct ieee80211_rx_status *rx_status) |
| { |
| struct rtl8723bu_rx_desc *rx_desc = |
| (struct rtl8723bu_rx_desc *)skb->data; |
| struct rtl8723au_phy_stats *phy_stats; |
| int drvinfo_sz, desc_shift; |
| |
| skb_pull(skb, sizeof(struct rtl8723bu_rx_desc)); |
| |
| phy_stats = (struct rtl8723au_phy_stats *)skb->data; |
| |
| drvinfo_sz = rx_desc->drvinfo_sz * 8; |
| desc_shift = rx_desc->shift; |
| skb_pull(skb, drvinfo_sz + desc_shift); |
| |
| if (rx_desc->rpt_sel) { |
| struct device *dev = &priv->udev->dev; |
| dev_dbg(dev, "%s: C2H packet\n", __func__); |
| return RX_TYPE_C2H; |
| } |
| |
| if (rx_desc->phy_stats) |
| rtl8xxxu_rx_parse_phystats(priv, rx_status, phy_stats, |
| rx_desc->rxmcs); |
| |
| rx_status->mactime = le32_to_cpu(rx_desc->tsfl); |
| rx_status->flag |= RX_FLAG_MACTIME_START; |
| |
| if (!rx_desc->swdec) |
| rx_status->flag |= RX_FLAG_DECRYPTED; |
| if (rx_desc->crc32) |
| rx_status->flag |= RX_FLAG_FAILED_FCS_CRC; |
| if (rx_desc->bw) |
| rx_status->flag |= RX_FLAG_40MHZ; |
| |
| if (rx_desc->rxmcs >= DESC_RATE_MCS0) { |
| rx_status->flag |= RX_FLAG_HT; |
| rx_status->rate_idx = rx_desc->rxmcs - DESC_RATE_MCS0; |
| } else { |
| rx_status->rate_idx = rx_desc->rxmcs; |
| } |
| |
| return RX_TYPE_DATA_PKT; |
| } |
| |
| static void rtl8723bu_handle_c2h(struct rtl8xxxu_priv *priv, |
| struct sk_buff *skb) |
| { |
| struct rtl8723bu_c2h *c2h = (struct rtl8723bu_c2h *)skb->data; |
| struct device *dev = &priv->udev->dev; |
| int len; |
| |
| len = skb->len - 2; |
| |
| dev_dbg(dev, "C2H ID %02x seq %02x, len %02x source %02x\n", |
| c2h->id, c2h->seq, len, c2h->bt_info.response_source); |
| |
| switch(c2h->id) { |
| case C2H_8723B_BT_INFO: |
| if (c2h->bt_info.response_source > |
| BT_INFO_SRC_8723B_BT_ACTIVE_SEND) |
| dev_dbg(dev, "C2H_BT_INFO WiFi only firmware\n"); |
| else |
| dev_dbg(dev, "C2H_BT_INFO BT/WiFi coexist firmware\n"); |
| |
| if (c2h->bt_info.bt_has_reset) |
| dev_dbg(dev, "BT has been reset\n"); |
| if (c2h->bt_info.tx_rx_mask) |
| dev_dbg(dev, "BT TRx mask\n"); |
| |
| break; |
| case C2H_8723B_BT_MP_INFO: |
| dev_dbg(dev, "C2H_MP_INFO ext ID %02x, status %02x\n", |
| c2h->bt_mp_info.ext_id, c2h->bt_mp_info.status); |
| break; |
| case C2H_8723B_RA_REPORT: |
| dev_dbg(dev, |
| "C2H RA RPT: rate %02x, unk %i, macid %02x, noise %i\n", |
| c2h->ra_report.rate, c2h->ra_report.dummy0_0, |
| c2h->ra_report.macid, c2h->ra_report.noisy_state); |
| break; |
| default: |
| dev_info(dev, "Unhandled C2H event %02x seq %02x\n", |
| c2h->id, c2h->seq); |
| print_hex_dump(KERN_INFO, "C2H content: ", DUMP_PREFIX_NONE, |
| 16, 1, c2h->raw.payload, len, false); |
| break; |
| } |
| } |
| |
| static void rtl8xxxu_rx_complete(struct urb *urb) |
| { |
| struct rtl8xxxu_rx_urb *rx_urb = |
| container_of(urb, struct rtl8xxxu_rx_urb, urb); |
| struct ieee80211_hw *hw = rx_urb->hw; |
| struct rtl8xxxu_priv *priv = hw->priv; |
| struct sk_buff *skb = (struct sk_buff *)urb->context; |
| struct ieee80211_rx_status *rx_status = IEEE80211_SKB_RXCB(skb); |
| struct device *dev = &priv->udev->dev; |
| __le32 *_rx_desc_le = (__le32 *)skb->data; |
| u32 *_rx_desc = (u32 *)skb->data; |
| int rx_type, i; |
| |
| for (i = 0; i < (sizeof(struct rtl8xxxu_rx_desc) / sizeof(u32)); i++) |
| _rx_desc[i] = le32_to_cpu(_rx_desc_le[i]); |
| |
| skb_put(skb, urb->actual_length); |
| |
| if (urb->status == 0) { |
| memset(rx_status, 0, sizeof(struct ieee80211_rx_status)); |
| |
| rx_type = priv->fops->parse_rx_desc(priv, skb, rx_status); |
| |
| rx_status->freq = hw->conf.chandef.chan->center_freq; |
| rx_status->band = hw->conf.chandef.chan->band; |
| |
| if (rx_type == RX_TYPE_DATA_PKT) |
| ieee80211_rx_irqsafe(hw, skb); |
| else { |
| rtl8723bu_handle_c2h(priv, skb); |
| dev_kfree_skb(skb); |
| } |
| |
| skb = NULL; |
| rx_urb->urb.context = NULL; |
| rtl8xxxu_queue_rx_urb(priv, rx_urb); |
| } else { |
| dev_dbg(dev, "%s: status %i\n", __func__, urb->status); |
| goto cleanup; |
| } |
| return; |
| |
| cleanup: |
| usb_free_urb(urb); |
| dev_kfree_skb(skb); |
| return; |
| } |
| |
| static int rtl8xxxu_submit_rx_urb(struct rtl8xxxu_priv *priv, |
| struct rtl8xxxu_rx_urb *rx_urb) |
| { |
| struct sk_buff *skb; |
| int skb_size; |
| int ret; |
| |
| skb_size = sizeof(struct rtl8xxxu_rx_desc) + RTL_RX_BUFFER_SIZE; |
| skb = __netdev_alloc_skb(NULL, skb_size, GFP_KERNEL); |
| if (!skb) |
| return -ENOMEM; |
| |
| memset(skb->data, 0, sizeof(struct rtl8xxxu_rx_desc)); |
| usb_fill_bulk_urb(&rx_urb->urb, priv->udev, priv->pipe_in, skb->data, |
| skb_size, rtl8xxxu_rx_complete, skb); |
| usb_anchor_urb(&rx_urb->urb, &priv->rx_anchor); |
| ret = usb_submit_urb(&rx_urb->urb, GFP_ATOMIC); |
| if (ret) |
| usb_unanchor_urb(&rx_urb->urb); |
| return ret; |
| } |
| |
| static void rtl8xxxu_int_complete(struct urb *urb) |
| { |
| struct rtl8xxxu_priv *priv = (struct rtl8xxxu_priv *)urb->context; |
| struct device *dev = &priv->udev->dev; |
| int ret; |
| |
| dev_dbg(dev, "%s: status %i\n", __func__, urb->status); |
| if (urb->status == 0) { |
| usb_anchor_urb(urb, &priv->int_anchor); |
| ret = usb_submit_urb(urb, GFP_ATOMIC); |
| if (ret) |
| usb_unanchor_urb(urb); |
| } else { |
| dev_info(dev, "%s: Error %i\n", __func__, urb->status); |
| } |
| } |
| |
| |
| static int rtl8xxxu_submit_int_urb(struct ieee80211_hw *hw) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| struct urb *urb; |
| u32 val32; |
| int ret; |
| |
| urb = usb_alloc_urb(0, GFP_KERNEL); |
| if (!urb) |
| return -ENOMEM; |
| |
| usb_fill_int_urb(urb, priv->udev, priv->pipe_interrupt, |
| priv->int_buf, USB_INTR_CONTENT_LENGTH, |
| rtl8xxxu_int_complete, priv, 1); |
| usb_anchor_urb(urb, &priv->int_anchor); |
| ret = usb_submit_urb(urb, GFP_KERNEL); |
| if (ret) { |
| usb_unanchor_urb(urb); |
| goto error; |
| } |
| |
| val32 = rtl8xxxu_read32(priv, REG_USB_HIMR); |
| val32 |= USB_HIMR_CPWM; |
| rtl8xxxu_write32(priv, REG_USB_HIMR, val32); |
| |
| error: |
| return ret; |
| } |
| |
| static int rtl8xxxu_add_interface(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| int ret; |
| u8 val8; |
| |
| switch (vif->type) { |
| case NL80211_IFTYPE_STATION: |
| rtl8723a_stop_tx_beacon(priv); |
| |
| val8 = rtl8xxxu_read8(priv, REG_BEACON_CTRL); |
| val8 |= BEACON_ATIM | BEACON_FUNCTION_ENABLE | |
| BEACON_DISABLE_TSF_UPDATE; |
| rtl8xxxu_write8(priv, REG_BEACON_CTRL, val8); |
| ret = 0; |
| break; |
| default: |
| ret = -EOPNOTSUPP; |
| } |
| |
| rtl8xxxu_set_linktype(priv, vif->type); |
| |
| return ret; |
| } |
| |
| static void rtl8xxxu_remove_interface(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| |
| dev_dbg(&priv->udev->dev, "%s\n", __func__); |
| } |
| |
| static int rtl8xxxu_config(struct ieee80211_hw *hw, u32 changed) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| struct device *dev = &priv->udev->dev; |
| u16 val16; |
| int ret = 0, channel; |
| bool ht40; |
| |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_CHANNEL) |
| dev_info(dev, |
| "%s: channel: %i (changed %08x chandef.width %02x)\n", |
| __func__, hw->conf.chandef.chan->hw_value, |
| changed, hw->conf.chandef.width); |
| |
| if (changed & IEEE80211_CONF_CHANGE_RETRY_LIMITS) { |
| val16 = ((hw->conf.long_frame_max_tx_count << |
| RETRY_LIMIT_LONG_SHIFT) & RETRY_LIMIT_LONG_MASK) | |
| ((hw->conf.short_frame_max_tx_count << |
| RETRY_LIMIT_SHORT_SHIFT) & RETRY_LIMIT_SHORT_MASK); |
| rtl8xxxu_write16(priv, REG_RETRY_LIMIT, val16); |
| } |
| |
| if (changed & IEEE80211_CONF_CHANGE_CHANNEL) { |
| switch (hw->conf.chandef.width) { |
| case NL80211_CHAN_WIDTH_20_NOHT: |
| case NL80211_CHAN_WIDTH_20: |
| ht40 = false; |
| break; |
| case NL80211_CHAN_WIDTH_40: |
| ht40 = true; |
| break; |
| default: |
| ret = -ENOTSUPP; |
| goto exit; |
| } |
| |
| channel = hw->conf.chandef.chan->hw_value; |
| |
| priv->fops->set_tx_power(priv, channel, ht40); |
| |
| priv->fops->config_channel(hw); |
| } |
| |
| exit: |
| return ret; |
| } |
| |
| static int rtl8xxxu_conf_tx(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, u16 queue, |
| const struct ieee80211_tx_queue_params *param) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| struct device *dev = &priv->udev->dev; |
| u32 val32; |
| u8 aifs, acm_ctrl, acm_bit; |
| |
| aifs = param->aifs; |
| |
| val32 = aifs | |
| fls(param->cw_min) << EDCA_PARAM_ECW_MIN_SHIFT | |
| fls(param->cw_max) << EDCA_PARAM_ECW_MAX_SHIFT | |
| (u32)param->txop << EDCA_PARAM_TXOP_SHIFT; |
| |
| acm_ctrl = rtl8xxxu_read8(priv, REG_ACM_HW_CTRL); |
| dev_dbg(dev, |
| "%s: IEEE80211 queue %02x val %08x, acm %i, acm_ctrl %02x\n", |
| __func__, queue, val32, param->acm, acm_ctrl); |
| |
| switch (queue) { |
| case IEEE80211_AC_VO: |
| acm_bit = ACM_HW_CTRL_VO; |
| rtl8xxxu_write32(priv, REG_EDCA_VO_PARAM, val32); |
| break; |
| case IEEE80211_AC_VI: |
| acm_bit = ACM_HW_CTRL_VI; |
| rtl8xxxu_write32(priv, REG_EDCA_VI_PARAM, val32); |
| break; |
| case IEEE80211_AC_BE: |
| acm_bit = ACM_HW_CTRL_BE; |
| rtl8xxxu_write32(priv, REG_EDCA_BE_PARAM, val32); |
| break; |
| case IEEE80211_AC_BK: |
| acm_bit = ACM_HW_CTRL_BK; |
| rtl8xxxu_write32(priv, REG_EDCA_BK_PARAM, val32); |
| break; |
| default: |
| acm_bit = 0; |
| break; |
| } |
| |
| if (param->acm) |
| acm_ctrl |= acm_bit; |
| else |
| acm_ctrl &= ~acm_bit; |
| rtl8xxxu_write8(priv, REG_ACM_HW_CTRL, acm_ctrl); |
| |
| return 0; |
| } |
| |
| static void rtl8xxxu_configure_filter(struct ieee80211_hw *hw, |
| unsigned int changed_flags, |
| unsigned int *total_flags, u64 multicast) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| u32 rcr = rtl8xxxu_read32(priv, REG_RCR); |
| |
| dev_dbg(&priv->udev->dev, "%s: changed_flags %08x, total_flags %08x\n", |
| __func__, changed_flags, *total_flags); |
| |
| /* |
| * FIF_ALLMULTI ignored as all multicast frames are accepted (REG_MAR) |
| */ |
| |
| if (*total_flags & FIF_FCSFAIL) |
| rcr |= RCR_ACCEPT_CRC32; |
| else |
| rcr &= ~RCR_ACCEPT_CRC32; |
| |
| /* |
| * FIF_PLCPFAIL not supported? |
| */ |
| |
| if (*total_flags & FIF_BCN_PRBRESP_PROMISC) |
| rcr &= ~RCR_CHECK_BSSID_BEACON; |
| else |
| rcr |= RCR_CHECK_BSSID_BEACON; |
| |
| if (*total_flags & FIF_CONTROL) |
| rcr |= RCR_ACCEPT_CTRL_FRAME; |
| else |
| rcr &= ~RCR_ACCEPT_CTRL_FRAME; |
| |
| if (*total_flags & FIF_OTHER_BSS) { |
| rcr |= RCR_ACCEPT_AP; |
| rcr &= ~RCR_CHECK_BSSID_MATCH; |
| } else { |
| rcr &= ~RCR_ACCEPT_AP; |
| rcr |= RCR_CHECK_BSSID_MATCH; |
| } |
| |
| if (*total_flags & FIF_PSPOLL) |
| rcr |= RCR_ACCEPT_PM; |
| else |
| rcr &= ~RCR_ACCEPT_PM; |
| |
| /* |
| * FIF_PROBE_REQ ignored as probe requests always seem to be accepted |
| */ |
| |
| rtl8xxxu_write32(priv, REG_RCR, rcr); |
| |
| *total_flags &= (FIF_ALLMULTI | FIF_FCSFAIL | FIF_BCN_PRBRESP_PROMISC | |
| FIF_CONTROL | FIF_OTHER_BSS | FIF_PSPOLL | |
| FIF_PROBE_REQ); |
| } |
| |
| static int rtl8xxxu_set_rts_threshold(struct ieee80211_hw *hw, u32 rts) |
| { |
| if (rts > 2347) |
| return -EINVAL; |
| |
| return 0; |
| } |
| |
| static int rtl8xxxu_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct ieee80211_key_conf *key) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| struct device *dev = &priv->udev->dev; |
| u8 mac_addr[ETH_ALEN]; |
| u8 val8; |
| u16 val16; |
| u32 val32; |
| int retval = -EOPNOTSUPP; |
| |
| dev_dbg(dev, "%s: cmd %02x, cipher %08x, index %i\n", |
| __func__, cmd, key->cipher, key->keyidx); |
| |
| if (vif->type != NL80211_IFTYPE_STATION) |
| return -EOPNOTSUPP; |
| |
| if (key->keyidx > 3) |
| return -EOPNOTSUPP; |
| |
| switch (key->cipher) { |
| case WLAN_CIPHER_SUITE_WEP40: |
| case WLAN_CIPHER_SUITE_WEP104: |
| |
| break; |
| case WLAN_CIPHER_SUITE_CCMP: |
| key->flags |= IEEE80211_KEY_FLAG_SW_MGMT_TX; |
| break; |
| case WLAN_CIPHER_SUITE_TKIP: |
| key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC; |
| default: |
| return -EOPNOTSUPP; |
| } |
| |
| if (key->flags & IEEE80211_KEY_FLAG_PAIRWISE) { |
| dev_dbg(dev, "%s: pairwise key\n", __func__); |
| ether_addr_copy(mac_addr, sta->addr); |
| } else { |
| dev_dbg(dev, "%s: group key\n", __func__); |
| eth_broadcast_addr(mac_addr); |
| } |
| |
| val16 = rtl8xxxu_read16(priv, REG_CR); |
| val16 |= CR_SECURITY_ENABLE; |
| rtl8xxxu_write16(priv, REG_CR, val16); |
| |
| val8 = SEC_CFG_TX_SEC_ENABLE | SEC_CFG_TXBC_USE_DEFKEY | |
| SEC_CFG_RX_SEC_ENABLE | SEC_CFG_RXBC_USE_DEFKEY; |
| val8 |= SEC_CFG_TX_USE_DEFKEY | SEC_CFG_RX_USE_DEFKEY; |
| rtl8xxxu_write8(priv, REG_SECURITY_CFG, val8); |
| |
| switch (cmd) { |
| case SET_KEY: |
| key->hw_key_idx = key->keyidx; |
| key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; |
| rtl8xxxu_cam_write(priv, key, mac_addr); |
| retval = 0; |
| break; |
| case DISABLE_KEY: |
| rtl8xxxu_write32(priv, REG_CAM_WRITE, 0x00000000); |
| val32 = CAM_CMD_POLLING | CAM_CMD_WRITE | |
| key->keyidx << CAM_CMD_KEY_SHIFT; |
| rtl8xxxu_write32(priv, REG_CAM_CMD, val32); |
| retval = 0; |
| break; |
| default: |
| dev_warn(dev, "%s: Unsupported command %02x\n", __func__, cmd); |
| } |
| |
| return retval; |
| } |
| |
| static int |
| rtl8xxxu_ampdu_action(struct ieee80211_hw *hw, struct ieee80211_vif *vif, |
| struct ieee80211_ampdu_params *params) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| struct device *dev = &priv->udev->dev; |
| u8 ampdu_factor, ampdu_density; |
| struct ieee80211_sta *sta = params->sta; |
| enum ieee80211_ampdu_mlme_action action = params->action; |
| |
| switch (action) { |
| case IEEE80211_AMPDU_TX_START: |
| dev_info(dev, "%s: IEEE80211_AMPDU_TX_START\n", __func__); |
| ampdu_factor = sta->ht_cap.ampdu_factor; |
| ampdu_density = sta->ht_cap.ampdu_density; |
| rtl8xxxu_set_ampdu_factor(priv, ampdu_factor); |
| rtl8xxxu_set_ampdu_min_space(priv, ampdu_density); |
| dev_dbg(dev, |
| "Changed HT: ampdu_factor %02x, ampdu_density %02x\n", |
| ampdu_factor, ampdu_density); |
| break; |
| case IEEE80211_AMPDU_TX_STOP_FLUSH: |
| dev_info(dev, "%s: IEEE80211_AMPDU_TX_STOP_FLUSH\n", __func__); |
| rtl8xxxu_set_ampdu_factor(priv, 0); |
| rtl8xxxu_set_ampdu_min_space(priv, 0); |
| break; |
| case IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: |
| dev_info(dev, "%s: IEEE80211_AMPDU_TX_STOP_FLUSH_CONT\n", |
| __func__); |
| rtl8xxxu_set_ampdu_factor(priv, 0); |
| rtl8xxxu_set_ampdu_min_space(priv, 0); |
| break; |
| case IEEE80211_AMPDU_RX_START: |
| dev_info(dev, "%s: IEEE80211_AMPDU_RX_START\n", __func__); |
| break; |
| case IEEE80211_AMPDU_RX_STOP: |
| dev_info(dev, "%s: IEEE80211_AMPDU_RX_STOP\n", __func__); |
| break; |
| default: |
| break; |
| } |
| return 0; |
| } |
| |
| static int rtl8xxxu_start(struct ieee80211_hw *hw) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| struct rtl8xxxu_rx_urb *rx_urb; |
| struct rtl8xxxu_tx_urb *tx_urb; |
| unsigned long flags; |
| int ret, i; |
| |
| ret = 0; |
| |
| init_usb_anchor(&priv->rx_anchor); |
| init_usb_anchor(&priv->tx_anchor); |
| init_usb_anchor(&priv->int_anchor); |
| |
| priv->fops->enable_rf(priv); |
| if (priv->usb_interrupts) { |
| ret = rtl8xxxu_submit_int_urb(hw); |
| if (ret) |
| goto exit; |
| } |
| |
| for (i = 0; i < RTL8XXXU_TX_URBS; i++) { |
| tx_urb = kmalloc(sizeof(struct rtl8xxxu_tx_urb), GFP_KERNEL); |
| if (!tx_urb) { |
| if (!i) |
| ret = -ENOMEM; |
| |
| goto error_out; |
| } |
| usb_init_urb(&tx_urb->urb); |
| INIT_LIST_HEAD(&tx_urb->list); |
| tx_urb->hw = hw; |
| list_add(&tx_urb->list, &priv->tx_urb_free_list); |
| priv->tx_urb_free_count++; |
| } |
| |
| priv->tx_stopped = false; |
| |
| spin_lock_irqsave(&priv->rx_urb_lock, flags); |
| priv->shutdown = false; |
| spin_unlock_irqrestore(&priv->rx_urb_lock, flags); |
| |
| for (i = 0; i < RTL8XXXU_RX_URBS; i++) { |
| rx_urb = kmalloc(sizeof(struct rtl8xxxu_rx_urb), GFP_KERNEL); |
| if (!rx_urb) { |
| if (!i) |
| ret = -ENOMEM; |
| |
| goto error_out; |
| } |
| usb_init_urb(&rx_urb->urb); |
| INIT_LIST_HEAD(&rx_urb->list); |
| rx_urb->hw = hw; |
| |
| ret = rtl8xxxu_submit_rx_urb(priv, rx_urb); |
| } |
| exit: |
| /* |
| * Accept all data and mgmt frames |
| */ |
| rtl8xxxu_write16(priv, REG_RXFLTMAP2, 0xffff); |
| rtl8xxxu_write16(priv, REG_RXFLTMAP0, 0xffff); |
| |
| rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, 0x6954341e); |
| |
| return ret; |
| |
| error_out: |
| rtl8xxxu_free_tx_resources(priv); |
| /* |
| * Disable all data and mgmt frames |
| */ |
| rtl8xxxu_write16(priv, REG_RXFLTMAP2, 0x0000); |
| rtl8xxxu_write16(priv, REG_RXFLTMAP0, 0x0000); |
| |
| return ret; |
| } |
| |
| static void rtl8xxxu_stop(struct ieee80211_hw *hw) |
| { |
| struct rtl8xxxu_priv *priv = hw->priv; |
| unsigned long flags; |
| |
| rtl8xxxu_write8(priv, REG_TXPAUSE, 0xff); |
| |
| rtl8xxxu_write16(priv, REG_RXFLTMAP0, 0x0000); |
| rtl8xxxu_write16(priv, REG_RXFLTMAP2, 0x0000); |
| |
| spin_lock_irqsave(&priv->rx_urb_lock, flags); |
| priv->shutdown = true; |
| spin_unlock_irqrestore(&priv->rx_urb_lock, flags); |
| |
| usb_kill_anchored_urbs(&priv->rx_anchor); |
| usb_kill_anchored_urbs(&priv->tx_anchor); |
| if (priv->usb_interrupts) |
| usb_kill_anchored_urbs(&priv->int_anchor); |
| |
| rtl8723a_disable_rf(priv); |
| |
| /* |
| * Disable interrupts |
| */ |
| if (priv->usb_interrupts) |
| rtl8xxxu_write32(priv, REG_USB_HIMR, 0); |
| |
| rtl8xxxu_free_rx_resources(priv); |
| rtl8xxxu_free_tx_resources(priv); |
| } |
| |
| static const struct ieee80211_ops rtl8xxxu_ops = { |
| .tx = rtl8xxxu_tx, |
| .add_interface = rtl8xxxu_add_interface, |
| .remove_interface = rtl8xxxu_remove_interface, |
| .config = rtl8xxxu_config, |
| .conf_tx = rtl8xxxu_conf_tx, |
| .bss_info_changed = rtl8xxxu_bss_info_changed, |
| .configure_filter = rtl8xxxu_configure_filter, |
| .set_rts_threshold = rtl8xxxu_set_rts_threshold, |
| .start = rtl8xxxu_start, |
| .stop = rtl8xxxu_stop, |
| .sw_scan_start = rtl8xxxu_sw_scan_start, |
| .sw_scan_complete = rtl8xxxu_sw_scan_complete, |
| .set_key = rtl8xxxu_set_key, |
| .ampdu_action = rtl8xxxu_ampdu_action, |
| }; |
| |
| static int rtl8xxxu_parse_usb(struct rtl8xxxu_priv *priv, |
| struct usb_interface *interface) |
| { |
| struct usb_interface_descriptor *interface_desc; |
| struct usb_host_interface *host_interface; |
| struct usb_endpoint_descriptor *endpoint; |
| struct device *dev = &priv->udev->dev; |
| int i, j = 0, endpoints; |
| u8 dir, xtype, num; |
| int ret = 0; |
| |
| host_interface = &interface->altsetting[0]; |
| interface_desc = &host_interface->desc; |
| endpoints = interface_desc->bNumEndpoints; |
| |
| for (i = 0; i < endpoints; i++) { |
| endpoint = &host_interface->endpoint[i].desc; |
| |
| dir = endpoint->bEndpointAddress & USB_ENDPOINT_DIR_MASK; |
| num = usb_endpoint_num(endpoint); |
| xtype = usb_endpoint_type(endpoint); |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_USB) |
| dev_dbg(dev, |
| "%s: endpoint: dir %02x, # %02x, type %02x\n", |
| __func__, dir, num, xtype); |
| if (usb_endpoint_dir_in(endpoint) && |
| usb_endpoint_xfer_bulk(endpoint)) { |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_USB) |
| dev_dbg(dev, "%s: in endpoint num %i\n", |
| __func__, num); |
| |
| if (priv->pipe_in) { |
| dev_warn(dev, |
| "%s: Too many IN pipes\n", __func__); |
| ret = -EINVAL; |
| goto exit; |
| } |
| |
| priv->pipe_in = usb_rcvbulkpipe(priv->udev, num); |
| } |
| |
| if (usb_endpoint_dir_in(endpoint) && |
| usb_endpoint_xfer_int(endpoint)) { |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_USB) |
| dev_dbg(dev, "%s: interrupt endpoint num %i\n", |
| __func__, num); |
| |
| if (priv->pipe_interrupt) { |
| dev_warn(dev, "%s: Too many INTERRUPT pipes\n", |
| __func__); |
| ret = -EINVAL; |
| goto exit; |
| } |
| |
| priv->pipe_interrupt = usb_rcvintpipe(priv->udev, num); |
| } |
| |
| if (usb_endpoint_dir_out(endpoint) && |
| usb_endpoint_xfer_bulk(endpoint)) { |
| if (rtl8xxxu_debug & RTL8XXXU_DEBUG_USB) |
| dev_dbg(dev, "%s: out endpoint num %i\n", |
| __func__, num); |
| if (j >= RTL8XXXU_OUT_ENDPOINTS) { |
| dev_warn(dev, |
| "%s: Too many OUT pipes\n", __func__); |
| ret = -EINVAL; |
| goto exit; |
| } |
| priv->out_ep[j++] = num; |
| } |
| } |
| exit: |
| priv->nr_out_eps = j; |
| return ret; |
| } |
| |
| static int rtl8xxxu_probe(struct usb_interface *interface, |
| const struct usb_device_id *id) |
| { |
| struct rtl8xxxu_priv *priv; |
| struct ieee80211_hw *hw; |
| struct usb_device *udev; |
| struct ieee80211_supported_band *sband; |
| int ret = 0; |
| int untested = 1; |
| |
| udev = usb_get_dev(interface_to_usbdev(interface)); |
| |
| switch (id->idVendor) { |
| case USB_VENDOR_ID_REALTEK: |
| switch(id->idProduct) { |
| case 0x1724: |
| case 0x8176: |
| case 0x8178: |
| case 0x817f: |
| untested = 0; |
| break; |
| } |
| break; |
| case 0x7392: |
| if (id->idProduct == 0x7811) |
| untested = 0; |
| break; |
| default: |
| break; |
| } |
| |
| if (untested) { |
| rtl8xxxu_debug |= RTL8XXXU_DEBUG_EFUSE; |
| dev_info(&udev->dev, |
| "This Realtek USB WiFi dongle (0x%04x:0x%04x) is untested!\n", |
| id->idVendor, id->idProduct); |
| dev_info(&udev->dev, |
| "Please report results to Jes.Sorensen@gmail.com\n"); |
| } |
| |
| hw = ieee80211_alloc_hw(sizeof(struct rtl8xxxu_priv), &rtl8xxxu_ops); |
| if (!hw) { |
| ret = -ENOMEM; |
| goto exit; |
| } |
| |
| priv = hw->priv; |
| priv->hw = hw; |
| priv->udev = udev; |
| priv->fops = (struct rtl8xxxu_fileops *)id->driver_info; |
| mutex_init(&priv->usb_buf_mutex); |
| mutex_init(&priv->h2c_mutex); |
| INIT_LIST_HEAD(&priv->tx_urb_free_list); |
| spin_lock_init(&priv->tx_urb_lock); |
| INIT_LIST_HEAD(&priv->rx_urb_pending_list); |
| spin_lock_init(&priv->rx_urb_lock); |
| INIT_WORK(&priv->rx_urb_wq, rtl8xxxu_rx_urb_work); |
| |
| usb_set_intfdata(interface, hw); |
| |
| ret = rtl8xxxu_parse_usb(priv, interface); |
| if (ret) |
| goto exit; |
| |
| ret = rtl8xxxu_identify_chip(priv); |
| if (ret) { |
| dev_err(&udev->dev, "Fatal - failed to identify chip\n"); |
| goto exit; |
| } |
| |
| ret = rtl8xxxu_read_efuse(priv); |
| if (ret) { |
| dev_err(&udev->dev, "Fatal - failed to read EFuse\n"); |
| goto exit; |
| } |
| |
| ret = priv->fops->parse_efuse(priv); |
| if (ret) { |
| dev_err(&udev->dev, "Fatal - failed to parse EFuse\n"); |
| goto exit; |
| } |
| |
| rtl8xxxu_print_chipinfo(priv); |
| |
| ret = priv->fops->load_firmware(priv); |
| if (ret) { |
| dev_err(&udev->dev, "Fatal - failed to load firmware\n"); |
| goto exit; |
| } |
| |
| ret = rtl8xxxu_init_device(hw); |
| |
| hw->wiphy->max_scan_ssids = 1; |
| hw->wiphy->max_scan_ie_len = IEEE80211_MAX_DATA_LEN; |
| hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION); |
| hw->queues = 4; |
| |
| sband = &rtl8xxxu_supported_band; |
| sband->ht_cap.ht_supported = true; |
| sband->ht_cap.ampdu_factor = IEEE80211_HT_MAX_AMPDU_64K; |
| sband->ht_cap.ampdu_density = IEEE80211_HT_MPDU_DENSITY_16; |
| sband->ht_cap.cap = IEEE80211_HT_CAP_SGI_20 | IEEE80211_HT_CAP_SGI_40; |
| memset(&sband->ht_cap.mcs, 0, sizeof(sband->ht_cap.mcs)); |
| sband->ht_cap.mcs.rx_mask[0] = 0xff; |
| sband->ht_cap.mcs.rx_mask[4] = 0x01; |
| if (priv->rf_paths > 1) { |
| sband->ht_cap.mcs.rx_mask[1] = 0xff; |
| sband->ht_cap.cap |= IEEE80211_HT_CAP_SGI_40; |
| } |
| sband->ht_cap.mcs.tx_params = IEEE80211_HT_MCS_TX_DEFINED; |
| /* |
| * Some APs will negotiate HT20_40 in a noisy environment leading |
| * to miserable performance. Rather than defaulting to this, only |
| * enable it if explicitly requested at module load time. |
| */ |
| if (rtl8xxxu_ht40_2g) { |
| dev_info(&udev->dev, "Enabling HT_20_40 on the 2.4GHz band\n"); |
| sband->ht_cap.cap |= IEEE80211_HT_CAP_SUP_WIDTH_20_40; |
| } |
| hw->wiphy->bands[IEEE80211_BAND_2GHZ] = sband; |
| |
| hw->wiphy->rts_threshold = 2347; |
| |
| SET_IEEE80211_DEV(priv->hw, &interface->dev); |
| SET_IEEE80211_PERM_ADDR(hw, priv->mac_addr); |
| |
| hw->extra_tx_headroom = priv->fops->tx_desc_size; |
| ieee80211_hw_set(hw, SIGNAL_DBM); |
| /* |
| * The firmware handles rate control |
| */ |
| ieee80211_hw_set(hw, HAS_RATE_CONTROL); |
| ieee80211_hw_set(hw, AMPDU_AGGREGATION); |
| |
| ret = ieee80211_register_hw(priv->hw); |
| if (ret) { |
| dev_err(&udev->dev, "%s: Failed to register: %i\n", |
| __func__, ret); |
| goto exit; |
| } |
| |
| exit: |
| if (ret < 0) |
| usb_put_dev(udev); |
| return ret; |
| } |
| |
| static void rtl8xxxu_disconnect(struct usb_interface *interface) |
| { |
| struct rtl8xxxu_priv *priv; |
| struct ieee80211_hw *hw; |
| |
| hw = usb_get_intfdata(interface); |
| priv = hw->priv; |
| |
| rtl8xxxu_disable_device(hw); |
| usb_set_intfdata(interface, NULL); |
| |
| dev_info(&priv->udev->dev, "disconnecting\n"); |
| |
| ieee80211_unregister_hw(hw); |
| |
| kfree(priv->fw_data); |
| mutex_destroy(&priv->usb_buf_mutex); |
| mutex_destroy(&priv->h2c_mutex); |
| |
| usb_put_dev(priv->udev); |
| ieee80211_free_hw(hw); |
| } |
| |
| static struct rtl8xxxu_fileops rtl8723au_fops = { |
| .parse_efuse = rtl8723au_parse_efuse, |
| .load_firmware = rtl8723au_load_firmware, |
| .power_on = rtl8723au_power_on, |
| .llt_init = rtl8xxxu_init_llt_table, |
| .phy_iq_calibrate = rtl8723au_phy_iq_calibrate, |
| .config_channel = rtl8723au_config_channel, |
| .parse_rx_desc = rtl8723au_parse_rx_desc, |
| .enable_rf = rtl8723a_enable_rf, |
| .set_tx_power = rtl8723a_set_tx_power, |
| .update_rate_mask = rtl8723au_update_rate_mask, |
| .report_connect = rtl8723au_report_connect, |
| .writeN_block_size = 1024, |
| .mbox_ext_reg = REG_HMBOX_EXT_0, |
| .mbox_ext_width = 2, |
| .tx_desc_size = sizeof(struct rtl8723au_tx_desc), |
| .adda_1t_init = 0x0b1b25a0, |
| .adda_1t_path_on = 0x0bdb25a0, |
| .adda_2t_path_on_a = 0x04db25a4, |
| .adda_2t_path_on_b = 0x0b1b25a4, |
| }; |
| |
| static struct rtl8xxxu_fileops rtl8723bu_fops = { |
| .parse_efuse = rtl8723bu_parse_efuse, |
| .load_firmware = rtl8723bu_load_firmware, |
| .power_on = rtl8723bu_power_on, |
| .llt_init = rtl8xxxu_auto_llt_table, |
| .phy_init_antenna_selection = rtl8723bu_phy_init_antenna_selection, |
| .phy_iq_calibrate = rtl8723bu_phy_iq_calibrate, |
| .config_channel = rtl8723bu_config_channel, |
| .init_bt = rtl8723bu_init_bt, |
| .parse_rx_desc = rtl8723bu_parse_rx_desc, |
| .init_aggregation = rtl8723bu_init_aggregation, |
| .init_statistics = rtl8723bu_init_statistics, |
| .enable_rf = rtl8723b_enable_rf, |
| .set_tx_power = rtl8723b_set_tx_power, |
| .update_rate_mask = rtl8723bu_update_rate_mask, |
| .report_connect = rtl8723bu_report_connect, |
| .writeN_block_size = 1024, |
| .mbox_ext_reg = REG_HMBOX_EXT0_8723B, |
| .mbox_ext_width = 4, |
| .tx_desc_size = sizeof(struct rtl8723bu_tx_desc), |
| .has_s0s1 = 1, |
| .adda_1t_init = 0x01c00014, |
| .adda_1t_path_on = 0x01c00014, |
| .adda_2t_path_on_a = 0x01c00014, |
| .adda_2t_path_on_b = 0x01c00014, |
| }; |
| |
| #ifdef CONFIG_RTL8XXXU_UNTESTED |
| |
| static struct rtl8xxxu_fileops rtl8192cu_fops = { |
| .parse_efuse = rtl8192cu_parse_efuse, |
| .load_firmware = rtl8192cu_load_firmware, |
| .power_on = rtl8192cu_power_on, |
| .llt_init = rtl8xxxu_init_llt_table, |
| .phy_iq_calibrate = rtl8723au_phy_iq_calibrate, |
| .config_channel = rtl8723au_config_channel, |
| .parse_rx_desc = rtl8723au_parse_rx_desc, |
| .enable_rf = rtl8723a_enable_rf, |
| .set_tx_power = rtl8723a_set_tx_power, |
| .update_rate_mask = rtl8723au_update_rate_mask, |
| .report_connect = rtl8723au_report_connect, |
| .writeN_block_size = 128, |
| .mbox_ext_reg = REG_HMBOX_EXT_0, |
| .mbox_ext_width = 2, |
| .tx_desc_size = sizeof(struct rtl8723au_tx_desc), |
| .adda_1t_init = 0x0b1b25a0, |
| .adda_1t_path_on = 0x0bdb25a0, |
| .adda_2t_path_on_a = 0x04db25a4, |
| .adda_2t_path_on_b = 0x0b1b25a4, |
| }; |
| |
| #endif |
| |
| static struct rtl8xxxu_fileops rtl8192eu_fops = { |
| .parse_efuse = rtl8192eu_parse_efuse, |
| .load_firmware = rtl8192eu_load_firmware, |
| .power_on = rtl8192eu_power_on, |
| .llt_init = rtl8xxxu_auto_llt_table, |
| .phy_iq_calibrate = rtl8723bu_phy_iq_calibrate, |
| .config_channel = rtl8723bu_config_channel, |
| .parse_rx_desc = rtl8723bu_parse_rx_desc, |
| .enable_rf = rtl8723b_enable_rf, |
| .set_tx_power = rtl8723b_set_tx_power, |
| .update_rate_mask = rtl8723au_update_rate_mask, |
| .report_connect = rtl8723au_report_connect, |
| .writeN_block_size = 128, |
| .mbox_ext_reg = REG_HMBOX_EXT0_8723B, |
| .mbox_ext_width = 4, |
| .tx_desc_size = sizeof(struct rtl8723au_tx_desc), |
| .has_s0s1 = 1, |
| .adda_1t_init = 0x0fc01616, |
| .adda_1t_path_on = 0x0fc01616, |
| .adda_2t_path_on_a = 0x0fc01616, |
| .adda_2t_path_on_b = 0x0fc01616, |
| }; |
| |
| static struct usb_device_id dev_table[] = { |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x8724, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8723au_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x1724, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8723au_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x0724, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8723au_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x818b, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192eu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0xb720, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8723bu_fops}, |
| #ifdef CONFIG_RTL8XXXU_UNTESTED |
| /* Still supported by rtlwifi */ |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x8176, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x8178, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x817f, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| /* Tested by Larry Finger */ |
| {USB_DEVICE_AND_INTERFACE_INFO(0x7392, 0x7811, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| /* Currently untested 8188 series devices */ |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x8191, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x8170, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x8177, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x817a, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x817b, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x817d, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x817e, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x818a, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x317f, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x1058, 0x0631, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x04bb, 0x094c, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x050d, 0x1102, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x06f8, 0xe033, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x07b8, 0x8189, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0846, 0x9041, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0b05, 0x17ba, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x1e1e, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x5088, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0df6, 0x0052, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0df6, 0x005c, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0eb0, 0x9071, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x103c, 0x1629, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x13d3, 0x3357, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x3308, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x330b, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2019, 0x4902, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2019, 0xab2a, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2019, 0xab2e, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2019, 0xed17, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x20f4, 0x648b, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x4855, 0x0090, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x4856, 0x0091, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0xcdab, 0x8010, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x04f2, 0xaff7, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x04f2, 0xaff9, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x04f2, 0xaffa, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x04f2, 0xaff8, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x04f2, 0xaffb, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x04f2, 0xaffc, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2019, 0x1201, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| /* Currently untested 8192 series devices */ |
| {USB_DEVICE_AND_INTERFACE_INFO(0x04bb, 0x0950, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x050d, 0x1004, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x050d, 0x2102, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x050d, 0x2103, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0586, 0x341f, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x06f8, 0xe035, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0b05, 0x17ab, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0df6, 0x0061, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0df6, 0x0070, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0789, 0x016d, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x07aa, 0x0056, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x07b8, 0x8178, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0846, 0x9021, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0846, 0xf001, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x2e2e, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0e66, 0x0019, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x0e66, 0x0020, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x3307, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x3309, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x330a, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2019, 0xab2b, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x20f4, 0x624d, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x2357, 0x0100, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x4855, 0x0091, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| {USB_DEVICE_AND_INTERFACE_INFO(0x7392, 0x7822, 0xff, 0xff, 0xff), |
| .driver_info = (unsigned long)&rtl8192cu_fops}, |
| #endif |
| { } |
| }; |
| |
| static struct usb_driver rtl8xxxu_driver = { |
| .name = DRIVER_NAME, |
| .probe = rtl8xxxu_probe, |
| .disconnect = rtl8xxxu_disconnect, |
| .id_table = dev_table, |
| .disable_hub_initiated_lpm = 1, |
| }; |
| |
| static int __init rtl8xxxu_module_init(void) |
| { |
| int res; |
| |
| res = usb_register(&rtl8xxxu_driver); |
| if (res < 0) |
| pr_err(DRIVER_NAME ": usb_register() failed (%i)\n", res); |
| |
| return res; |
| } |
| |
| static void __exit rtl8xxxu_module_exit(void) |
| { |
| usb_deregister(&rtl8xxxu_driver); |
| } |
| |
| |
| MODULE_DEVICE_TABLE(usb, dev_table); |
| |
| module_init(rtl8xxxu_module_init); |
| module_exit(rtl8xxxu_module_exit); |