bnx2x: Pause settings
Pause settings
- 1G pause was not working due to missing write to the emac block
(TX_MODE_FLOW_EN)
- The flow control should use the negotiated result (after autoneg) so
we should save both the requested autoneg and the result
- The HW credits with flow control at 1G speed were not optimized and
caused low throughput
- It is recommended to turn off flow control if the MTU is bigger than
5000B due to internal buffers size
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c
index 3b63c8c..36fa356 100644
--- a/drivers/net/bnx2x_link.c
+++ b/drivers/net/bnx2x_link.c
@@ -38,7 +38,6 @@
#define ETH_MAX_JUMBO_PACKET_SIZE 9600
#define MDIO_ACCESS_TIMEOUT 1000
#define BMAC_CONTROL_RX_ENABLE 2
-#define MAX_MTU_SIZE 5000
/***********************************************************/
/* Shortcut definitions */
@@ -298,11 +297,13 @@
EMAC_RX_MODE_FLOW_EN);
bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
- EMAC_TX_MODE_EXT_PAUSE_EN);
+ (EMAC_TX_MODE_EXT_PAUSE_EN |
+ EMAC_TX_MODE_FLOW_EN));
if (vars->flow_ctrl & FLOW_CTRL_TX)
bnx2x_bits_en(bp, emac_base +
EMAC_REG_EMAC_TX_MODE,
- EMAC_TX_MODE_EXT_PAUSE_EN);
+ (EMAC_TX_MODE_EXT_PAUSE_EN |
+ EMAC_TX_MODE_FLOW_EN));
}
/* KEEP_VLAN_TAG, promiscuous */
@@ -591,9 +592,9 @@
vars->flow_ctrl &= ~FLOW_CTRL_RX;
if (vars->phy_flags & PHY_XGXS_FLAG) {
- if (params->req_line_speed &&
- ((params->req_line_speed == SPEED_10) ||
- (params->req_line_speed == SPEED_100))) {
+ if (vars->line_speed &&
+ ((vars->line_speed == SPEED_10) ||
+ (vars->line_speed == SPEED_100))) {
vars->phy_flags |= PHY_SGMII_FLAG;
} else {
vars->phy_flags &= ~PHY_SGMII_FLAG;
@@ -670,7 +671,6 @@
u8 port = params->port;
u32 init_crd, crd;
u32 count = 1000;
- u32 pause = 0;
/* disable port */
REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x1);
@@ -693,33 +693,25 @@
return -EINVAL;
}
- if (flow_ctrl & FLOW_CTRL_RX)
- pause = 1;
- REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, pause);
- if (pause) {
+ if (flow_ctrl & FLOW_CTRL_RX ||
+ line_speed == SPEED_10 ||
+ line_speed == SPEED_100 ||
+ line_speed == SPEED_1000 ||
+ line_speed == SPEED_2500) {
+ REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 1);
/* update threshold */
REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0);
/* update init credit */
- init_crd = 778; /* (800-18-4) */
+ init_crd = 778; /* (800-18-4) */
} else {
u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE +
ETH_OVREHEAD)/16;
-
+ REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0);
/* update threshold */
REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, thresh);
/* update init credit */
switch (line_speed) {
- case SPEED_10:
- case SPEED_100:
- case SPEED_1000:
- init_crd = thresh + 55 - 22;
- break;
-
- case SPEED_2500:
- init_crd = thresh + 138 - 22;
- break;
-
case SPEED_10000:
init_crd = thresh + 553 - 22;
break;
@@ -1114,7 +1106,7 @@
MDIO_COMBO_IEEE0_MII_CONTROL, ®_val);
/* CL37 Autoneg Enabled */
- if (params->req_line_speed == SPEED_AUTO_NEG)
+ if (vars->line_speed == SPEED_AUTO_NEG)
reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_AN_EN;
else /* CL37 Autoneg Disabled */
reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
@@ -1132,7 +1124,7 @@
MDIO_REG_BANK_SERDES_DIGITAL,
MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, ®_val);
reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN;
- if (params->req_line_speed == SPEED_AUTO_NEG)
+ if (vars->line_speed == SPEED_AUTO_NEG)
reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET;
else
reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET;
@@ -1148,7 +1140,7 @@
MDIO_REG_BANK_BAM_NEXT_PAGE,
MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
®_val);
- if (params->req_line_speed == SPEED_AUTO_NEG) {
+ if (vars->line_speed == SPEED_AUTO_NEG) {
/* Enable BAM aneg Mode and TetonII aneg Mode */
reg_val |= (MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE |
MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN);
@@ -1164,7 +1156,7 @@
reg_val);
/* Enable Clause 73 Aneg */
- if ((params->req_line_speed == SPEED_AUTO_NEG) &&
+ if ((vars->line_speed == SPEED_AUTO_NEG) &&
(SUPPORT_CL73)) {
/* Enable BAM Station Manager */
@@ -1226,7 +1218,8 @@
}
/* program SerDes, forced speed */
-static void bnx2x_program_serdes(struct link_params *params)
+static void bnx2x_program_serdes(struct link_params *params,
+ struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
u16 reg_val;
@@ -1248,28 +1241,35 @@
/* program speed
- needed only if the speed is greater than 1G (2.5G or 10G) */
- if (!((params->req_line_speed == SPEED_1000) ||
- (params->req_line_speed == SPEED_100) ||
- (params->req_line_speed == SPEED_10))) {
- CL45_RD_OVER_CL22(bp, params->port,
+ CL45_RD_OVER_CL22(bp, params->port,
params->phy_addr,
MDIO_REG_BANK_SERDES_DIGITAL,
MDIO_SERDES_DIGITAL_MISC1, ®_val);
- /* clearing the speed value before setting the right speed */
- reg_val &= ~MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK;
+ /* clearing the speed value before setting the right speed */
+ DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val);
+
+ reg_val &= ~(MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK |
+ MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL);
+
+ if (!((vars->line_speed == SPEED_1000) ||
+ (vars->line_speed == SPEED_100) ||
+ (vars->line_speed == SPEED_10))) {
+
reg_val |= (MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M |
MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL);
- if (params->req_line_speed == SPEED_10000)
+ if (vars->line_speed == SPEED_10000)
reg_val |=
MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4;
- if (params->req_line_speed == SPEED_13000)
+ if (vars->line_speed == SPEED_13000)
reg_val |=
MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G;
- CL45_WR_OVER_CL22(bp, params->port,
+ }
+
+ CL45_WR_OVER_CL22(bp, params->port,
params->phy_addr,
MDIO_REG_BANK_SERDES_DIGITAL,
MDIO_SERDES_DIGITAL_MISC1, reg_val);
- }
+
}
static void bnx2x_set_brcm_cl37_advertisment(struct link_params *params)
@@ -1295,48 +1295,49 @@
MDIO_OVER_1G_UP3, 0);
}
-static void bnx2x_set_ieee_aneg_advertisment(struct link_params *params,
- u32 *ieee_fc)
+static void bnx2x_calc_ieee_aneg_adv(struct link_params *params, u32 *ieee_fc)
{
- struct bnx2x *bp = params->bp;
- /* for AN, we are always publishing full duplex */
- u16 an_adv = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX;
-
+ *ieee_fc = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX;
/* resolve pause mode and advertisement
* Please refer to Table 28B-3 of the 802.3ab-1999 spec */
switch (params->req_flow_ctrl) {
case FLOW_CTRL_AUTO:
- if (params->mtu <= MAX_MTU_SIZE) {
- an_adv |=
+ if (params->req_fc_auto_adv == FLOW_CTRL_BOTH) {
+ *ieee_fc |=
MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
} else {
- an_adv |=
+ *ieee_fc |=
MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
}
break;
case FLOW_CTRL_TX:
- an_adv |=
+ *ieee_fc |=
MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
break;
case FLOW_CTRL_RX:
case FLOW_CTRL_BOTH:
- an_adv |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
+ *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
break;
case FLOW_CTRL_NONE:
default:
- an_adv |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE;
+ *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE;
break;
}
+}
- *ieee_fc = an_adv;
+static void bnx2x_set_ieee_aneg_advertisment(struct link_params *params,
+ u32 ieee_fc)
+{
+ struct bnx2x *bp = params->bp;
+ /* for AN, we are always publishing full duplex */
CL45_WR_OVER_CL22(bp, params->port,
params->phy_addr,
MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV, an_adv);
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV, (u16)ieee_fc);
}
static void bnx2x_restart_autoneg(struct link_params *params)
@@ -1382,7 +1383,8 @@
}
}
-static void bnx2x_initialize_sgmii_process(struct link_params *params)
+static void bnx2x_initialize_sgmii_process(struct link_params *params,
+ struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
u16 control1;
@@ -1406,7 +1408,7 @@
control1);
/* if forced speed */
- if (!(params->req_line_speed == SPEED_AUTO_NEG)) {
+ if (!(vars->line_speed == SPEED_AUTO_NEG)) {
/* set speed, disable autoneg */
u16 mii_control;
@@ -1419,7 +1421,7 @@
MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK|
MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX);
- switch (params->req_line_speed) {
+ switch (vars->line_speed) {
case SPEED_100:
mii_control |=
MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100;
@@ -1433,8 +1435,8 @@
break;
default:
/* invalid speed for SGMII */
- DP(NETIF_MSG_LINK, "Invalid req_line_speed 0x%x\n",
- params->req_line_speed);
+ DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
+ vars->line_speed);
break;
}
@@ -1460,20 +1462,20 @@
*/
static void bnx2x_pause_resolve(struct link_vars *vars, u32 pause_result)
-{
- switch (pause_result) { /* ASYM P ASYM P */
- case 0xb: /* 1 0 1 1 */
+{ /* LD LP */
+ switch (pause_result) { /* ASYM P ASYM P */
+ case 0xb: /* 1 0 1 1 */
vars->flow_ctrl = FLOW_CTRL_TX;
break;
- case 0xe: /* 1 1 1 0 */
+ case 0xe: /* 1 1 1 0 */
vars->flow_ctrl = FLOW_CTRL_RX;
break;
- case 0x5: /* 0 1 0 1 */
- case 0x7: /* 0 1 1 1 */
- case 0xd: /* 1 1 0 1 */
- case 0xf: /* 1 1 1 1 */
+ case 0x5: /* 0 1 0 1 */
+ case 0x7: /* 0 1 1 1 */
+ case 0xd: /* 1 1 0 1 */
+ case 0xf: /* 1 1 1 1 */
vars->flow_ctrl = FLOW_CTRL_BOTH;
break;
@@ -1487,8 +1489,8 @@
{
struct bnx2x *bp = params->bp;
u8 ext_phy_addr;
- u16 ld_pause; /* local */
- u16 lp_pause; /* link partner */
+ u16 ld_pause; /* local */
+ u16 lp_pause; /* link partner */
u16 an_complete; /* AN complete */
u16 pause_result;
u8 ret = 0;
@@ -1531,6 +1533,28 @@
DP(NETIF_MSG_LINK, "Ext PHY pause result 0x%x \n",
pause_result);
bnx2x_pause_resolve(vars, pause_result);
+ if (vars->flow_ctrl == FLOW_CTRL_NONE &&
+ ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) {
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_FC_LD, &ld_pause);
+
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_FC_LP, &lp_pause);
+ pause_result = (ld_pause &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 5;
+ pause_result |= (lp_pause &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 7;
+
+ bnx2x_pause_resolve(vars, pause_result);
+ DP(NETIF_MSG_LINK, "Ext PHY CL37 pause result 0x%x \n",
+ pause_result);
+ }
}
return ret;
}
@@ -1573,13 +1597,10 @@
(bnx2x_ext_phy_resove_fc(params, vars))) {
return;
} else {
- vars->flow_ctrl = params->req_flow_ctrl;
- if (vars->flow_ctrl == FLOW_CTRL_AUTO) {
- if (params->mtu <= MAX_MTU_SIZE)
- vars->flow_ctrl = FLOW_CTRL_BOTH;
- else
- vars->flow_ctrl = FLOW_CTRL_TX;
- }
+ if (params->req_flow_ctrl == FLOW_CTRL_AUTO)
+ vars->flow_ctrl = params->req_fc_auto_adv;
+ else
+ vars->flow_ctrl = params->req_flow_ctrl;
}
DP(NETIF_MSG_LINK, "flow_ctrl 0x%x\n", vars->flow_ctrl);
}
@@ -1709,12 +1730,12 @@
}
if (vars->flow_ctrl & FLOW_CTRL_TX)
- vars->link_status |=
- LINK_STATUS_TX_FLOW_CONTROL_ENABLED;
+ vars->link_status |=
+ LINK_STATUS_TX_FLOW_CONTROL_ENABLED;
if (vars->flow_ctrl & FLOW_CTRL_RX)
- vars->link_status |=
- LINK_STATUS_RX_FLOW_CONTROL_ENABLED;
+ vars->link_status |=
+ LINK_STATUS_RX_FLOW_CONTROL_ENABLED;
} else { /* link_down */
DP(NETIF_MSG_LINK, "phy link down\n");
@@ -2286,13 +2307,16 @@
MDIO_AN_REG_ADV_PAUSE, &val);
val &= ~MDIO_AN_REG_ADV_PAUSE_BOTH;
+
/* Please refer to Table 28B-3 of 802.3ab-1999 spec. */
- if (vars->ieee_fc &
+ if ((vars->ieee_fc &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) ==
MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) {
val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC;
}
- if (vars->ieee_fc &
+ if ((vars->ieee_fc &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) ==
MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) {
val |=
MDIO_AN_REG_ADV_PAUSE_PAUSE;
@@ -2339,7 +2363,7 @@
bnx2x_set_autoneg(params, vars);
/* program speed and duplex */
- bnx2x_program_serdes(params);
+ bnx2x_program_serdes(params, vars);
} else { /* AN_mode */
DP(NETIF_MSG_LINK, "not SGMII, AN\n");
@@ -2349,7 +2373,7 @@
/* program duplex & pause advertisement (for aneg) */
bnx2x_set_ieee_aneg_advertisment(params,
- &vars->ieee_fc);
+ vars->ieee_fc);
/* enable autoneg */
bnx2x_set_autoneg(params, vars);
@@ -2361,7 +2385,7 @@
} else { /* SGMII mode */
DP(NETIF_MSG_LINK, "SGMII\n");
- bnx2x_initialize_sgmii_process(params);
+ bnx2x_initialize_sgmii_process(params, vars);
}
}
@@ -2481,7 +2505,7 @@
ext_phy_type,
ext_phy_addr,
MDIO_AN_DEVAD,
- MDIO_AN_REG_CL37_FD,
+ MDIO_AN_REG_CL37_FC_LP,
0x0020);
/* Enable CL37 AN */
bnx2x_cl45_write(bp, params->port,
@@ -2657,13 +2681,13 @@
ext_phy_type,
ext_phy_addr,
MDIO_AN_DEVAD,
- MDIO_AN_REG_CL37_CL73, 0x040c);
+ MDIO_AN_REG_CL37_FC_LD, 0x040c);
/* Add support for CL37 (passive mode) II */
bnx2x_cl45_write(bp, params->port,
ext_phy_type,
ext_phy_addr,
MDIO_AN_DEVAD,
- MDIO_AN_REG_CL37_FD, 0x20);
+ MDIO_AN_REG_CL37_FC_LD, 0x20);
/* Add support for CL37 (passive mode) III */
bnx2x_cl45_write(bp, params->port,
ext_phy_type,
@@ -2785,7 +2809,7 @@
static u8 bnx2x_ext_phy_is_link_up(struct link_params *params,
- struct link_vars *vars)
+ struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
u32 ext_phy_type;
@@ -2826,6 +2850,8 @@
MDIO_PMA_REG_RX_SD, &rx_sd);
DP(NETIF_MSG_LINK, "8705 rx_sd 0x%x\n", rx_sd);
ext_phy_link_up = (rx_sd & 0x1);
+ if (ext_phy_link_up)
+ vars->line_speed = SPEED_10000;
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
@@ -3734,7 +3760,7 @@
req_line_speed*/
vars->line_speed = params->req_line_speed;
- bnx2x_set_ieee_aneg_advertisment(params, &vars->ieee_fc);
+ bnx2x_calc_ieee_aneg_adv(params, &vars->ieee_fc);
/* init ext phy and enable link state int */
non_ext_phy = ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) ||