| /* |
| * Copyright (C) 2009 Sascha Hauer, Pengutronix |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <linux/types.h> |
| #include <linux/init.h> |
| |
| #include <linux/platform_device.h> |
| #include <linux/mtd/physmap.h> |
| #include <linux/mtd/plat-ram.h> |
| #include <linux/memory.h> |
| #include <linux/gpio.h> |
| #include <linux/smc911x.h> |
| #include <linux/interrupt.h> |
| #include <linux/delay.h> |
| #include <linux/i2c.h> |
| #include <linux/platform_data/at24.h> |
| #include <linux/usb/otg.h> |
| #include <linux/usb/ulpi.h> |
| |
| #include <asm/mach-types.h> |
| #include <asm/mach/arch.h> |
| #include <asm/mach/time.h> |
| #include <asm/mach/map.h> |
| |
| #include "common.h" |
| #include "devices-imx35.h" |
| #include "ehci.h" |
| #include "hardware.h" |
| #include "iomux-mx35.h" |
| #include "ulpi.h" |
| |
| static const struct fb_videomode fb_modedb[] = { |
| { |
| /* 240x320 @ 60 Hz */ |
| .name = "Sharp-LQ035Q7", |
| .refresh = 60, |
| .xres = 240, |
| .yres = 320, |
| .pixclock = 185925, |
| .left_margin = 9, |
| .right_margin = 16, |
| .upper_margin = 7, |
| .lower_margin = 9, |
| .hsync_len = 1, |
| .vsync_len = 1, |
| .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_SHARP_MODE | FB_SYNC_CLK_INVERT | FB_SYNC_CLK_IDLE_EN, |
| .vmode = FB_VMODE_NONINTERLACED, |
| .flag = 0, |
| }, { |
| /* 240x320 @ 60 Hz */ |
| .name = "TX090", |
| .refresh = 60, |
| .xres = 240, |
| .yres = 320, |
| .pixclock = 38255, |
| .left_margin = 144, |
| .right_margin = 0, |
| .upper_margin = 7, |
| .lower_margin = 40, |
| .hsync_len = 96, |
| .vsync_len = 1, |
| .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH, |
| .vmode = FB_VMODE_NONINTERLACED, |
| .flag = 0, |
| }, |
| }; |
| |
| static struct mx3fb_platform_data mx3fb_pdata __initdata = { |
| .name = "Sharp-LQ035Q7", |
| .mode = fb_modedb, |
| .num_modes = ARRAY_SIZE(fb_modedb), |
| }; |
| |
| static struct physmap_flash_data pcm043_flash_data = { |
| .width = 2, |
| }; |
| |
| static struct resource pcm043_flash_resource = { |
| .start = 0xa0000000, |
| .end = 0xa1ffffff, |
| .flags = IORESOURCE_MEM, |
| }; |
| |
| static struct platform_device pcm043_flash = { |
| .name = "physmap-flash", |
| .id = 0, |
| .dev = { |
| .platform_data = &pcm043_flash_data, |
| }, |
| .resource = &pcm043_flash_resource, |
| .num_resources = 1, |
| }; |
| |
| static const struct imxuart_platform_data uart_pdata __initconst = { |
| .flags = IMXUART_HAVE_RTSCTS, |
| }; |
| |
| static const struct imxi2c_platform_data pcm043_i2c0_data __initconst = { |
| .bitrate = 50000, |
| }; |
| |
| static struct at24_platform_data board_eeprom = { |
| .byte_len = 4096, |
| .page_size = 32, |
| .flags = AT24_FLAG_ADDR16, |
| }; |
| |
| static struct i2c_board_info pcm043_i2c_devices[] = { |
| { |
| I2C_BOARD_INFO("at24", 0x52), /* E0=0, E1=1, E2=0 */ |
| .platform_data = &board_eeprom, |
| }, { |
| I2C_BOARD_INFO("pcf8563", 0x51), |
| }, |
| }; |
| |
| static struct platform_device *devices[] __initdata = { |
| &pcm043_flash, |
| }; |
| |
| static iomux_v3_cfg_t pcm043_pads[] = { |
| /* UART1 */ |
| MX35_PAD_CTS1__UART1_CTS, |
| MX35_PAD_RTS1__UART1_RTS, |
| MX35_PAD_TXD1__UART1_TXD_MUX, |
| MX35_PAD_RXD1__UART1_RXD_MUX, |
| /* UART2 */ |
| MX35_PAD_CTS2__UART2_CTS, |
| MX35_PAD_RTS2__UART2_RTS, |
| MX35_PAD_TXD2__UART2_TXD_MUX, |
| MX35_PAD_RXD2__UART2_RXD_MUX, |
| /* FEC */ |
| MX35_PAD_FEC_TX_CLK__FEC_TX_CLK, |
| MX35_PAD_FEC_RX_CLK__FEC_RX_CLK, |
| MX35_PAD_FEC_RX_DV__FEC_RX_DV, |
| MX35_PAD_FEC_COL__FEC_COL, |
| MX35_PAD_FEC_RDATA0__FEC_RDATA_0, |
| MX35_PAD_FEC_TDATA0__FEC_TDATA_0, |
| MX35_PAD_FEC_TX_EN__FEC_TX_EN, |
| MX35_PAD_FEC_MDC__FEC_MDC, |
| MX35_PAD_FEC_MDIO__FEC_MDIO, |
| MX35_PAD_FEC_TX_ERR__FEC_TX_ERR, |
| MX35_PAD_FEC_RX_ERR__FEC_RX_ERR, |
| MX35_PAD_FEC_CRS__FEC_CRS, |
| MX35_PAD_FEC_RDATA1__FEC_RDATA_1, |
| MX35_PAD_FEC_TDATA1__FEC_TDATA_1, |
| MX35_PAD_FEC_RDATA2__FEC_RDATA_2, |
| MX35_PAD_FEC_TDATA2__FEC_TDATA_2, |
| MX35_PAD_FEC_RDATA3__FEC_RDATA_3, |
| MX35_PAD_FEC_TDATA3__FEC_TDATA_3, |
| /* I2C1 */ |
| MX35_PAD_I2C1_CLK__I2C1_SCL, |
| MX35_PAD_I2C1_DAT__I2C1_SDA, |
| /* Display */ |
| MX35_PAD_LD0__IPU_DISPB_DAT_0, |
| MX35_PAD_LD1__IPU_DISPB_DAT_1, |
| MX35_PAD_LD2__IPU_DISPB_DAT_2, |
| MX35_PAD_LD3__IPU_DISPB_DAT_3, |
| MX35_PAD_LD4__IPU_DISPB_DAT_4, |
| MX35_PAD_LD5__IPU_DISPB_DAT_5, |
| MX35_PAD_LD6__IPU_DISPB_DAT_6, |
| MX35_PAD_LD7__IPU_DISPB_DAT_7, |
| MX35_PAD_LD8__IPU_DISPB_DAT_8, |
| MX35_PAD_LD9__IPU_DISPB_DAT_9, |
| MX35_PAD_LD10__IPU_DISPB_DAT_10, |
| MX35_PAD_LD11__IPU_DISPB_DAT_11, |
| MX35_PAD_LD12__IPU_DISPB_DAT_12, |
| MX35_PAD_LD13__IPU_DISPB_DAT_13, |
| MX35_PAD_LD14__IPU_DISPB_DAT_14, |
| MX35_PAD_LD15__IPU_DISPB_DAT_15, |
| MX35_PAD_LD16__IPU_DISPB_DAT_16, |
| MX35_PAD_LD17__IPU_DISPB_DAT_17, |
| MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC, |
| MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK, |
| MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY, |
| MX35_PAD_CONTRAST__IPU_DISPB_CONTR, |
| MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC, |
| MX35_PAD_D3_REV__IPU_DISPB_D3_REV, |
| MX35_PAD_D3_CLS__IPU_DISPB_D3_CLS, |
| /* gpio */ |
| MX35_PAD_ATA_CS0__GPIO2_6, |
| /* USB host */ |
| MX35_PAD_I2C2_CLK__USB_TOP_USBH2_PWR, |
| MX35_PAD_I2C2_DAT__USB_TOP_USBH2_OC, |
| /* SSI */ |
| MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS, |
| MX35_PAD_STXD4__AUDMUX_AUD4_TXD, |
| MX35_PAD_SRXD4__AUDMUX_AUD4_RXD, |
| MX35_PAD_SCK4__AUDMUX_AUD4_TXC, |
| /* CAN2 */ |
| MX35_PAD_TX5_RX0__CAN2_TXCAN, |
| MX35_PAD_TX4_RX1__CAN2_RXCAN, |
| /* esdhc */ |
| MX35_PAD_SD1_CMD__ESDHC1_CMD, |
| MX35_PAD_SD1_CLK__ESDHC1_CLK, |
| MX35_PAD_SD1_DATA0__ESDHC1_DAT0, |
| MX35_PAD_SD1_DATA1__ESDHC1_DAT1, |
| MX35_PAD_SD1_DATA2__ESDHC1_DAT2, |
| MX35_PAD_SD1_DATA3__ESDHC1_DAT3, |
| MX35_PAD_ATA_DATA10__GPIO2_23, /* WriteProtect */ |
| MX35_PAD_ATA_DATA11__GPIO2_24, /* CardDetect */ |
| }; |
| |
| #define AC97_GPIO_TXFS IMX_GPIO_NR(2, 31) |
| #define AC97_GPIO_TXD IMX_GPIO_NR(2, 28) |
| #define AC97_GPIO_RESET IMX_GPIO_NR(2, 0) |
| #define SD1_GPIO_WP IMX_GPIO_NR(2, 23) |
| #define SD1_GPIO_CD IMX_GPIO_NR(2, 24) |
| |
| static void pcm043_ac97_warm_reset(struct snd_ac97 *ac97) |
| { |
| iomux_v3_cfg_t txfs_gpio = MX35_PAD_STXFS4__GPIO2_31; |
| iomux_v3_cfg_t txfs = MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS; |
| int ret; |
| |
| ret = gpio_request(AC97_GPIO_TXFS, "SSI"); |
| if (ret) { |
| printk("failed to get GPIO_TXFS: %d\n", ret); |
| return; |
| } |
| |
| mxc_iomux_v3_setup_pad(txfs_gpio); |
| |
| /* warm reset */ |
| gpio_direction_output(AC97_GPIO_TXFS, 1); |
| udelay(2); |
| gpio_set_value(AC97_GPIO_TXFS, 0); |
| |
| gpio_free(AC97_GPIO_TXFS); |
| mxc_iomux_v3_setup_pad(txfs); |
| } |
| |
| static void pcm043_ac97_cold_reset(struct snd_ac97 *ac97) |
| { |
| iomux_v3_cfg_t txfs_gpio = MX35_PAD_STXFS4__GPIO2_31; |
| iomux_v3_cfg_t txfs = MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS; |
| iomux_v3_cfg_t txd_gpio = MX35_PAD_STXD4__GPIO2_28; |
| iomux_v3_cfg_t txd = MX35_PAD_STXD4__AUDMUX_AUD4_TXD; |
| iomux_v3_cfg_t reset_gpio = MX35_PAD_SD2_CMD__GPIO2_0; |
| int ret; |
| |
| ret = gpio_request(AC97_GPIO_TXFS, "SSI"); |
| if (ret) |
| goto err1; |
| |
| ret = gpio_request(AC97_GPIO_TXD, "SSI"); |
| if (ret) |
| goto err2; |
| |
| ret = gpio_request(AC97_GPIO_RESET, "SSI"); |
| if (ret) |
| goto err3; |
| |
| mxc_iomux_v3_setup_pad(txfs_gpio); |
| mxc_iomux_v3_setup_pad(txd_gpio); |
| mxc_iomux_v3_setup_pad(reset_gpio); |
| |
| gpio_direction_output(AC97_GPIO_TXFS, 0); |
| gpio_direction_output(AC97_GPIO_TXD, 0); |
| |
| /* cold reset */ |
| gpio_direction_output(AC97_GPIO_RESET, 0); |
| udelay(10); |
| gpio_direction_output(AC97_GPIO_RESET, 1); |
| |
| mxc_iomux_v3_setup_pad(txd); |
| mxc_iomux_v3_setup_pad(txfs); |
| |
| gpio_free(AC97_GPIO_RESET); |
| err3: |
| gpio_free(AC97_GPIO_TXD); |
| err2: |
| gpio_free(AC97_GPIO_TXFS); |
| err1: |
| if (ret) |
| printk("%s failed with %d\n", __func__, ret); |
| mdelay(1); |
| } |
| |
| static const struct imx_ssi_platform_data pcm043_ssi_pdata __initconst = { |
| .ac97_reset = pcm043_ac97_cold_reset, |
| .ac97_warm_reset = pcm043_ac97_warm_reset, |
| .flags = IMX_SSI_USE_AC97, |
| }; |
| |
| static const struct mxc_nand_platform_data |
| pcm037_nand_board_info __initconst = { |
| .width = 1, |
| .hw_ecc = 1, |
| }; |
| |
| static int pcm043_otg_init(struct platform_device *pdev) |
| { |
| return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI); |
| } |
| |
| static struct mxc_usbh_platform_data otg_pdata __initdata = { |
| .init = pcm043_otg_init, |
| .portsc = MXC_EHCI_MODE_UTMI, |
| }; |
| |
| static int pcm043_usbh1_init(struct platform_device *pdev) |
| { |
| return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_SINGLE_UNI | |
| MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN); |
| } |
| |
| static const struct mxc_usbh_platform_data usbh1_pdata __initconst = { |
| .init = pcm043_usbh1_init, |
| .portsc = MXC_EHCI_MODE_SERIAL, |
| }; |
| |
| static const struct fsl_usb2_platform_data otg_device_pdata __initconst = { |
| .operating_mode = FSL_USB2_DR_DEVICE, |
| .phy_mode = FSL_USB2_PHY_UTMI, |
| }; |
| |
| static bool otg_mode_host __initdata; |
| |
| static int __init pcm043_otg_mode(char *options) |
| { |
| if (!strcmp(options, "host")) |
| otg_mode_host = true; |
| else if (!strcmp(options, "device")) |
| otg_mode_host = false; |
| else |
| pr_info("otg_mode neither \"host\" nor \"device\". " |
| "Defaulting to device\n"); |
| return 1; |
| } |
| __setup("otg_mode=", pcm043_otg_mode); |
| |
| static struct esdhc_platform_data sd1_pdata = { |
| .wp_gpio = SD1_GPIO_WP, |
| .cd_gpio = SD1_GPIO_CD, |
| .wp_type = ESDHC_WP_GPIO, |
| .cd_type = ESDHC_CD_GPIO, |
| }; |
| |
| /* |
| * Board specific initialization. |
| */ |
| static void __init pcm043_init(void) |
| { |
| imx35_soc_init(); |
| |
| mxc_iomux_v3_setup_multiple_pads(pcm043_pads, ARRAY_SIZE(pcm043_pads)); |
| |
| imx35_add_fec(NULL); |
| platform_add_devices(devices, ARRAY_SIZE(devices)); |
| imx35_add_imx2_wdt(); |
| |
| imx35_add_imx_uart0(&uart_pdata); |
| imx35_add_mxc_nand(&pcm037_nand_board_info); |
| imx35_add_imx_ssi(0, &pcm043_ssi_pdata); |
| |
| imx35_add_imx_uart1(&uart_pdata); |
| |
| i2c_register_board_info(0, pcm043_i2c_devices, |
| ARRAY_SIZE(pcm043_i2c_devices)); |
| |
| imx35_add_imx_i2c0(&pcm043_i2c0_data); |
| |
| imx35_add_ipu_core(); |
| imx35_add_mx3_sdc_fb(&mx3fb_pdata); |
| |
| if (otg_mode_host) { |
| otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS | |
| ULPI_OTG_DRVVBUS_EXT); |
| if (otg_pdata.otg) |
| imx35_add_mxc_ehci_otg(&otg_pdata); |
| } |
| imx35_add_mxc_ehci_hs(&usbh1_pdata); |
| |
| if (!otg_mode_host) |
| imx35_add_fsl_usb2_udc(&otg_device_pdata); |
| |
| imx35_add_flexcan1(); |
| imx35_add_sdhci_esdhc_imx(0, &sd1_pdata); |
| } |
| |
| static void __init pcm043_timer_init(void) |
| { |
| mx35_clocks_init(); |
| } |
| |
| MACHINE_START(PCM043, "Phytec Phycore pcm043") |
| /* Maintainer: Pengutronix */ |
| .atag_offset = 0x100, |
| .map_io = mx35_map_io, |
| .init_early = imx35_init_early, |
| .init_irq = mx35_init_irq, |
| .init_time = pcm043_timer_init, |
| .init_machine = pcm043_init, |
| .restart = mxc_restart, |
| MACHINE_END |