drivers/tty/serial/8250/8250_mtk.c - kernel/msm-4.19 - Gitiles

 /*
  * Mediatek 8250 driver.
  *
  * Copyright (c) 2014 MundoReader S.L.
  * Author: Matthias Brugger <matthias.bgg@gmail.com>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
  * (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  */
 #include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/init.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/serial_8250.h>
 #include <linux/serial_reg.h>

 #include "8250.h"

 #define UART_MTK_HIGHS		0x09	/* Highspeed register */
 #define UART_MTK_SAMPLE_COUNT	0x0a	/* Sample count register */
 #define UART_MTK_SAMPLE_POINT	0x0b	/* Sample point register */
 #define MTK_UART_RATE_FIX	0x0d	/* UART Rate Fix Register */

 struct mtk8250_data {
 	int			line;
 	struct clk		*uart_clk;
 	struct clk		*bus_clk;
 };

 static void
 mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
 			struct ktermios *old)
 {
 	unsigned long flags;
 	unsigned int baud, quot;

 	struct uart_8250_port *up =
 		container_of(port, struct uart_8250_port, port);

 	serial8250_do_set_termios(port, termios, old);

 	/*
 	 * Mediatek UARTs use an extra highspeed register (UART_MTK_HIGHS)
 	 *
 	 * We need to recalcualte the quot register, as the claculation depends
 	 * on the vaule in the highspeed register.
 	 *
 	 * Some baudrates are not supported by the chip, so we use the next
 	 * lower rate supported and update termios c_flag.
 	 *
 	 * If highspeed register is set to 3, we need to specify sample count
 	 * and sample point to increase accuracy. If not, we reset the
 	 * registers to their default values.
 	 */
 	baud = uart_get_baud_rate(port, termios, old,
 				  port->uartclk / 16 / 0xffff,
 				  port->uartclk / 16);

 	if (baud <= 115200) {
 		serial_port_out(port, UART_MTK_HIGHS, 0x0);
 		quot = uart_get_divisor(port, baud);
 	} else if (baud <= 576000) {
 		serial_port_out(port, UART_MTK_HIGHS, 0x2);

 		/* Set to next lower baudrate supported */
 		if ((baud == 500000) || (baud == 576000))
 			baud = 460800;
 		quot = DIV_ROUND_UP(port->uartclk, 4 * baud);
 	} else {
 		serial_port_out(port, UART_MTK_HIGHS, 0x3);

 		/* Set to highest baudrate supported */
 		if (baud >= 1152000)
 			baud = 921600;
 		quot = DIV_ROUND_UP(port->uartclk, 256 * baud);
 	}

 	/*
 	 * Ok, we're now changing the port state.  Do it with
 	 * interrupts disabled.
 	 */
 	spin_lock_irqsave(&port->lock, flags);

 	/* set DLAB we have cval saved in up->lcr from the call to the core */
 	serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
 	serial_dl_write(up, quot);

 	/* reset DLAB */
 	serial_port_out(port, UART_LCR, up->lcr);

 	if (baud > 460800) {
 		unsigned int tmp;

 		tmp = DIV_ROUND_CLOSEST(port->uartclk, quot * baud);
 		serial_port_out(port, UART_MTK_SAMPLE_COUNT, tmp - 1);
 		serial_port_out(port, UART_MTK_SAMPLE_POINT,
 					(tmp - 2) >> 1);
 	} else {
 		serial_port_out(port, UART_MTK_SAMPLE_COUNT, 0x00);
 		serial_port_out(port, UART_MTK_SAMPLE_POINT, 0xff);
 	}

 	spin_unlock_irqrestore(&port->lock, flags);
 	/* Don't rewrite B0 */
 	if (tty_termios_baud_rate(termios))
 		tty_termios_encode_baud_rate(termios, baud, baud);
 }

 static int __maybe_unused mtk8250_runtime_suspend(struct device *dev)
 {
 	struct mtk8250_data *data = dev_get_drvdata(dev);

 	clk_disable_unprepare(data->uart_clk);
 	clk_disable_unprepare(data->bus_clk);

 	return 0;
 }

 static int __maybe_unused mtk8250_runtime_resume(struct device *dev)
 {
 	struct mtk8250_data *data = dev_get_drvdata(dev);
 	int err;

 	err = clk_prepare_enable(data->uart_clk);
 	if (err) {
 		dev_warn(dev, "Can't enable clock\n");
 		return err;
 	}

 	err = clk_prepare_enable(data->bus_clk);
 	if (err) {
 		dev_warn(dev, "Can't enable bus clock\n");
 		return err;
 	}

 	return 0;
 }

 static void
 mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
 {
 	if (!state)
 		pm_runtime_get_sync(port->dev);

 	serial8250_do_pm(port, state, old);

 	if (state)
 		pm_runtime_put_sync_suspend(port->dev);
 }

 static int mtk8250_probe_of(struct platform_device *pdev, struct uart_port *p,
 			   struct mtk8250_data *data)
 {
 	data->uart_clk = devm_clk_get(&pdev->dev, "baud");
 	if (IS_ERR(data->uart_clk)) {
 		/*
 		 * For compatibility with older device trees try unnamed
 		 * clk when no baud clk can be found.
 		 */
 		data->uart_clk = devm_clk_get(&pdev->dev, NULL);
 		if (IS_ERR(data->uart_clk)) {
 			dev_warn(&pdev->dev, "Can't get uart clock\n");
 			return PTR_ERR(data->uart_clk);
 		}

 		return 0;
 	}

 	data->bus_clk = devm_clk_get(&pdev->dev, "bus");
 	if (IS_ERR(data->bus_clk))
 		return PTR_ERR(data->bus_clk);

 	return 0;
 }

 static int mtk8250_probe(struct platform_device *pdev)
 {
 	struct uart_8250_port uart = {};
 	struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	struct mtk8250_data *data;
 	int err;

 	if (!regs || !irq) {
 		dev_err(&pdev->dev, "no registers/irq defined\n");
 		return -EINVAL;
 	}

 	uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
 					 resource_size(regs));
 	if (!uart.port.membase)
 		return -ENOMEM;

 	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;

 	if (pdev->dev.of_node) {
 		err = mtk8250_probe_of(pdev, &uart.port, data);
 		if (err)
 			return err;
 	} else
 		return -ENODEV;

 	spin_lock_init(&uart.port.lock);
 	uart.port.mapbase = regs->start;
 	uart.port.irq = irq->start;
 	uart.port.pm = mtk8250_do_pm;
 	uart.port.type = PORT_16550;
 	uart.port.flags = UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
 	uart.port.dev = &pdev->dev;
 	uart.port.iotype = UPIO_MEM32;
 	uart.port.regshift = 2;
 	uart.port.private_data = data;
 	uart.port.set_termios = mtk8250_set_termios;
 	uart.port.uartclk = clk_get_rate(data->uart_clk);

 	/* Disable Rate Fix function */
 	writel(0x0, uart.port.membase +
 			(MTK_UART_RATE_FIX << uart.port.regshift));

 	platform_set_drvdata(pdev, data);

 	pm_runtime_enable(&pdev->dev);
 	if (!pm_runtime_enabled(&pdev->dev)) {
 		err = mtk8250_runtime_resume(&pdev->dev);
 		if (err)
 			return err;
 	}

 	data->line = serial8250_register_8250_port(&uart);
 	if (data->line < 0)
 		return data->line;

 	return 0;
 }

 static int __maybe_unused mtk8250_suspend(struct device *dev)
 {
 	struct mtk8250_data *data = dev_get_drvdata(dev);

 	serial8250_suspend_port(data->line);

 	return 0;
 }

 static int __maybe_unused mtk8250_resume(struct device *dev)
 {
 	struct mtk8250_data *data = dev_get_drvdata(dev);

 	serial8250_resume_port(data->line);

 	return 0;
 }

 static const struct dev_pm_ops mtk8250_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(mtk8250_suspend, mtk8250_resume)
 	SET_RUNTIME_PM_OPS(mtk8250_runtime_suspend, mtk8250_runtime_resume,
 				NULL)
 };

 static const struct of_device_id mtk8250_of_match[] = {
 	{ .compatible = "mediatek,mt6577-uart" },
 	{ /* Sentinel */ }
 };

 static struct platform_driver mtk8250_platform_driver = {
 	.driver = {
 		.name			= "mt6577-uart",
 		.pm			= &mtk8250_pm_ops,
 		.of_match_table		= mtk8250_of_match,
 		.suppress_bind_attrs	= true,

 	},
 	.probe			= mtk8250_probe,
 };
 builtin_platform_driver(mtk8250_platform_driver);

 #ifdef CONFIG_SERIAL_8250_CONSOLE
 static int __init early_mtk8250_setup(struct earlycon_device *device,
 					const char *options)
 {
 	if (!device->port.membase)
 		return -ENODEV;

 	device->port.iotype = UPIO_MEM32;

 	return early_serial8250_setup(device, NULL);
 }

 OF_EARLYCON_DECLARE(mtk8250, "mediatek,mt6577-uart", early_mtk8250_setup);
 #endif
	/*
	* Mediatek 8250 driver.
	*
	* Copyright (c) 2014 MundoReader S.L.
	* Author: Matthias Brugger <matthias.bgg@gmail.com>
	*
	* This program is free software; you can redistribute it and/or modify
	* it under the terms of the GNU General Public License as published by
	* the Free Software Foundation; either version 2 of the License, or
	* (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*/
	#include <linux/clk.h>
	#include <linux/io.h>
	#include <linux/init.h>
	#include <linux/of_irq.h>
	#include <linux/of_platform.h>
	#include <linux/platform_device.h>
	#include <linux/pm_runtime.h>
	#include <linux/serial_8250.h>
	#include <linux/serial_reg.h>

	#include "8250.h"

	#define UART_MTK_HIGHS 0x09 /* Highspeed register */
	#define UART_MTK_SAMPLE_COUNT 0x0a /* Sample count register */
	#define UART_MTK_SAMPLE_POINT 0x0b /* Sample point register */
	#define MTK_UART_RATE_FIX 0x0d /* UART Rate Fix Register */

	struct mtk8250_data {
	int line;
	struct clk *uart_clk;
	struct clk *bus_clk;
	};

	static void
	mtk8250_set_termios(struct uart_port port, struct ktermios termios,
	struct ktermios *old)
	{
	unsigned long flags;
	unsigned int baud, quot;

	struct uart_8250_port *up =
	container_of(port, struct uart_8250_port, port);

	serial8250_do_set_termios(port, termios, old);

	/*
	* Mediatek UARTs use an extra highspeed register (UART_MTK_HIGHS)
	*
	* We need to recalcualte the quot register, as the claculation depends
	* on the vaule in the highspeed register.
	*
	* Some baudrates are not supported by the chip, so we use the next
	* lower rate supported and update termios c_flag.
	*
	* If highspeed register is set to 3, we need to specify sample count
	* and sample point to increase accuracy. If not, we reset the
	* registers to their default values.
	*/
	baud = uart_get_baud_rate(port, termios, old,
	port->uartclk / 16 / 0xffff,
	port->uartclk / 16);

	if (baud <= 115200) {
	serial_port_out(port, UART_MTK_HIGHS, 0x0);
	quot = uart_get_divisor(port, baud);
	} else if (baud <= 576000) {
	serial_port_out(port, UART_MTK_HIGHS, 0x2);

	/* Set to next lower baudrate supported */
	if ((baud == 500000) \|\| (baud == 576000))
	baud = 460800;
	quot = DIV_ROUND_UP(port->uartclk, 4 * baud);
	} else {
	serial_port_out(port, UART_MTK_HIGHS, 0x3);

	/* Set to highest baudrate supported */
	if (baud >= 1152000)
	baud = 921600;
	quot = DIV_ROUND_UP(port->uartclk, 256 * baud);
	}

	/*
	* Ok, we're now changing the port state. Do it with
	* interrupts disabled.
	*/
	spin_lock_irqsave(&port->lock, flags);

	/* set DLAB we have cval saved in up->lcr from the call to the core */
	serial_port_out(port, UART_LCR, up->lcr \| UART_LCR_DLAB);
	serial_dl_write(up, quot);

	/* reset DLAB */
	serial_port_out(port, UART_LCR, up->lcr);

	if (baud > 460800) {
	unsigned int tmp;

	tmp = DIV_ROUND_CLOSEST(port->uartclk, quot * baud);
	serial_port_out(port, UART_MTK_SAMPLE_COUNT, tmp - 1);
	serial_port_out(port, UART_MTK_SAMPLE_POINT,
	(tmp - 2) >> 1);
	} else {
	serial_port_out(port, UART_MTK_SAMPLE_COUNT, 0x00);
	serial_port_out(port, UART_MTK_SAMPLE_POINT, 0xff);
	}

	spin_unlock_irqrestore(&port->lock, flags);
	/* Don't rewrite B0 */
	if (tty_termios_baud_rate(termios))
	tty_termios_encode_baud_rate(termios, baud, baud);
	}

	static int __maybe_unused mtk8250_runtime_suspend(struct device *dev)
	{
	struct mtk8250_data *data = dev_get_drvdata(dev);

	clk_disable_unprepare(data->uart_clk);
	clk_disable_unprepare(data->bus_clk);

	return 0;
	}

	static int __maybe_unused mtk8250_runtime_resume(struct device *dev)
	{
	struct mtk8250_data *data = dev_get_drvdata(dev);
	int err;

	err = clk_prepare_enable(data->uart_clk);
	if (err) {
	dev_warn(dev, "Can't enable clock\n");
	return err;
	}

	err = clk_prepare_enable(data->bus_clk);
	if (err) {
	dev_warn(dev, "Can't enable bus clock\n");
	return err;
	}

	return 0;
	}

	static void
	mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
	{
	if (!state)
	pm_runtime_get_sync(port->dev);

	serial8250_do_pm(port, state, old);

	if (state)
	pm_runtime_put_sync_suspend(port->dev);
	}

	static int mtk8250_probe_of(struct platform_device pdev, struct uart_port p,
	struct mtk8250_data *data)
	{
	data->uart_clk = devm_clk_get(&pdev->dev, "baud");
	if (IS_ERR(data->uart_clk)) {
	/*
	* For compatibility with older device trees try unnamed
	* clk when no baud clk can be found.
	*/
	data->uart_clk = devm_clk_get(&pdev->dev, NULL);
	if (IS_ERR(data->uart_clk)) {
	dev_warn(&pdev->dev, "Can't get uart clock\n");
	return PTR_ERR(data->uart_clk);
	}

	return 0;
	}

	data->bus_clk = devm_clk_get(&pdev->dev, "bus");
	if (IS_ERR(data->bus_clk))
	return PTR_ERR(data->bus_clk);

	return 0;
	}

	static int mtk8250_probe(struct platform_device *pdev)
	{
	struct uart_8250_port uart = {};
	struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
	struct mtk8250_data *data;
	int err;

	if (!regs \|\| !irq) {
	dev_err(&pdev->dev, "no registers/irq defined\n");
	return -EINVAL;
	}

	uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
	resource_size(regs));
	if (!uart.port.membase)
	return -ENOMEM;

	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
	if (!data)
	return -ENOMEM;

	if (pdev->dev.of_node) {
	err = mtk8250_probe_of(pdev, &uart.port, data);
	if (err)
	return err;
	} else
	return -ENODEV;

	spin_lock_init(&uart.port.lock);
	uart.port.mapbase = regs->start;
	uart.port.irq = irq->start;
	uart.port.pm = mtk8250_do_pm;
	uart.port.type = PORT_16550;
	uart.port.flags = UPF_BOOT_AUTOCONF \| UPF_FIXED_PORT;
	uart.port.dev = &pdev->dev;
	uart.port.iotype = UPIO_MEM32;
	uart.port.regshift = 2;
	uart.port.private_data = data;
	uart.port.set_termios = mtk8250_set_termios;
	uart.port.uartclk = clk_get_rate(data->uart_clk);

	/* Disable Rate Fix function */
	writel(0x0, uart.port.membase +
	(MTK_UART_RATE_FIX << uart.port.regshift));

	platform_set_drvdata(pdev, data);

	pm_runtime_enable(&pdev->dev);
	if (!pm_runtime_enabled(&pdev->dev)) {
	err = mtk8250_runtime_resume(&pdev->dev);
	if (err)
	return err;
	}

	data->line = serial8250_register_8250_port(&uart);
	if (data->line < 0)
	return data->line;

	return 0;
	}

	static int __maybe_unused mtk8250_suspend(struct device *dev)
	{
	struct mtk8250_data *data = dev_get_drvdata(dev);

	serial8250_suspend_port(data->line);

	return 0;
	}

	static int __maybe_unused mtk8250_resume(struct device *dev)
	{
	struct mtk8250_data *data = dev_get_drvdata(dev);

	serial8250_resume_port(data->line);

	return 0;
	}

	static const struct dev_pm_ops mtk8250_pm_ops = {
	SET_SYSTEM_SLEEP_PM_OPS(mtk8250_suspend, mtk8250_resume)
	SET_RUNTIME_PM_OPS(mtk8250_runtime_suspend, mtk8250_runtime_resume,
	NULL)
	};

	static const struct of_device_id mtk8250_of_match[] = {
	{ .compatible = "mediatek,mt6577-uart" },
	{ /* Sentinel */ }
	};

	static struct platform_driver mtk8250_platform_driver = {
	.driver = {
	.name = "mt6577-uart",
	.pm = &mtk8250_pm_ops,
	.of_match_table = mtk8250_of_match,
	.suppress_bind_attrs = true,

	},
	.probe = mtk8250_probe,
	};
	builtin_platform_driver(mtk8250_platform_driver);

	#ifdef CONFIG_SERIAL_8250_CONSOLE
	static int __init early_mtk8250_setup(struct earlycon_device *device,
	const char *options)
	{
	if (!device->port.membase)
	return -ENODEV;

	device->port.iotype = UPIO_MEM32;

	return early_serial8250_setup(device, NULL);
	}

	OF_EARLYCON_DECLARE(mtk8250, "mediatek,mt6577-uart", early_mtk8250_setup);
	#endif