ARM: mvebu: Add Armada 388 General Purpose Development Board support
The A388-GP is a board produced by Marvell that holds
- 1 PCIe slot
- 2 mini PCIe slot (one of them is multiplexed with the PCIe slot,
muxing is selected through the GPIO expander)
- 1 16MB SPI-NOR
- 2 Gigabit Ethernet ports
- 4 SATA ports (2 of them are multiplexed with the mini PCIe slots,
muxing is selected through the GPIO expander)
- 1 SDIO slot
- 1 USB3 port
- 2 USB2 port
- 2 GPIO/interrupts expander on I2C
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3ed928e..17ee1d6 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -537,6 +537,7 @@
dtb-$(CONFIG_MACH_ARMADA_38X) += \
armada-385-db-ap.dtb \
armada-388-db.dtb \
+ armada-388-gp.dtb \
armada-388-rd.dtb
dtb-$(CONFIG_MACH_ARMADA_XP) += \
armada-xp-axpwifiap.dtb \
diff --git a/arch/arm/boot/dts/armada-388-gp.dts b/arch/arm/boot/dts/armada-388-gp.dts
new file mode 100644
index 0000000..4df22bf
--- /dev/null
+++ b/arch/arm/boot/dts/armada-388-gp.dts
@@ -0,0 +1,288 @@
+/*
+ * Device Tree file for Marvell Armada 385 development board
+ * (RD-88F6820-GP)
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-388.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Marvell Armada 385 GP";
+ compatible = "marvell,a385-gp", "marvell,armada388", "marvell,armada380";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = &uart0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x80000000>; /* 2 GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+ internal-regs {
+ spi@10600 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p128";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+ };
+ };
+
+ i2c@11000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+ /*
+ * The EEPROM located at adresse 54 is needed
+ * for the boot - DO NOT ERASE IT -
+ */
+
+ expander0: pca9555@20 {
+ compatible = "nxp,pca9555";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pca0_pins>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x20>;
+ };
+
+ expander1: pca9555@21 {
+ compatible = "nxp,pca9555";
+ pinctrl-names = "default";
+ interrupt-parent = <&gpio0>;
+ interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x21>;
+ };
+
+ };
+
+ serial@12000 {
+ /*
+ * Exported on the micro USB connector CON16
+ * through an FTDI
+ */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+ };
+
+ /* GE1 CON15 */
+ ethernet@30000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ge1_rgmii_pins>;
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+
+ /* CON4 */
+ usb@50000 {
+ vcc-supply = <®_usb2_0_vbus>;
+ status = "okay";
+ };
+
+ /* GE0 CON1 */
+ ethernet@70000 {
+ pinctrl-names = "default";
+ /*
+ * The Reference Clock 0 is used to provide a
+ * clock to the PHY
+ */
+ pinctrl-0 = <&ge0_rgmii_pins>, <&ref_clk0_pins>;
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+
+
+ mdio@72004 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ phy1: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+
+ sata@a8000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sata0_pins>, <&sata1_pins>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sata@e0000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sata2_pins>, <&sata3_pins>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sdhci@d8000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhci_pins>;
+ cd-gpios = <&expander0 5 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ wp-inverted;
+ bus-width = <8>;
+ status = "okay";
+ };
+
+ /* CON5 */
+ usb3@f0000 {
+ vcc-supply = <®_usb2_1_vbus>;
+ status = "okay";
+ };
+
+ /* CON7 */
+ usb3@f8000 {
+ vcc-supply = <®_usb3_vbus>;
+ status = "okay";
+ };
+ };
+
+ pcie-controller {
+ status = "okay";
+ /*
+ * One PCIe units is accessible through
+ * standard PCIe slot on the board.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ /*
+ * The two other PCIe units are accessible
+ * through mini PCIe slot on the board.
+ */
+ pcie@2,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
+ pcie@3,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ gpio-fan {
+ compatible = "gpio-fan";
+ gpios = <&expander1 3 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = < 0 0
+ 3000 1>;
+ };
+ };
+
+ reg_usb3_vbus: usb3-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb3-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&expander1 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb2_0_vbus: v5-vbus0 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-vbus0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&expander1 14 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb2_1_vbus: v5-vbus1 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-vbus1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb2_1_vbus: v5-vbus1 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-vbus1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&pinctrl {
+ pca0_pins: pca0_pins {
+ marvell,pins = "mpp18";
+ marvell,function = "gpio";
+ };
+};