| /* |
| * arch/arm/mach-ks8695/pci.c |
| * |
| * Copyright (C) 2003, Micrel Semiconductors |
| * Copyright (C) 2006, Greg Ungerer <gerg@snapgear.com> |
| * Copyright (C) 2006, Ben Dooks |
| * Copyright (C) 2007, Andrew Victor |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/pci.h> |
| #include <linux/mm.h> |
| #include <linux/init.h> |
| #include <linux/irq.h> |
| #include <linux/delay.h> |
| |
| #include <asm/io.h> |
| #include <asm/signal.h> |
| #include <asm/mach/pci.h> |
| #include <asm/hardware.h> |
| |
| #include <asm/arch/devices.h> |
| #include <asm/arch/regs-pci.h> |
| |
| |
| static int pci_dbg; |
| static int pci_cfg_dbg; |
| |
| |
| static void ks8695_pci_setupconfig(unsigned int bus_nr, unsigned int devfn, unsigned int where) |
| { |
| unsigned long pbca; |
| |
| pbca = PBCA_ENABLE | (where & ~3); |
| pbca |= PCI_SLOT(devfn) << 11 ; |
| pbca |= PCI_FUNC(devfn) << 8; |
| pbca |= bus_nr << 16; |
| |
| if (bus_nr == 0) { |
| /* use Type-0 transaction */ |
| __raw_writel(pbca, KS8695_PCI_VA + KS8695_PBCA); |
| } else { |
| /* use Type-1 transaction */ |
| __raw_writel(pbca | PBCA_TYPE1, KS8695_PCI_VA + KS8695_PBCA); |
| } |
| } |
| |
| |
| /* |
| * The KS8695 datasheet prohibits anything other than 32bit accesses |
| * to the IO registers, so all our configuration must be done with |
| * 32bit operations, and the correct bit masking and shifting. |
| */ |
| |
| static int ks8695_pci_readconfig(struct pci_bus *bus, |
| unsigned int devfn, int where, int size, u32 *value) |
| { |
| ks8695_pci_setupconfig(bus->number, devfn, where); |
| |
| *value = __raw_readl(KS8695_PCI_VA + KS8695_PBCD); |
| |
| switch (size) { |
| case 4: |
| break; |
| case 2: |
| *value = *value >> ((where & 2) * 8); |
| *value &= 0xffff; |
| break; |
| case 1: |
| *value = *value >> ((where & 3) * 8); |
| *value &= 0xff; |
| break; |
| } |
| |
| if (pci_cfg_dbg) { |
| printk("read: %d,%08x,%02x,%d: %08x (%08x)\n", |
| bus->number, devfn, where, size, *value, |
| __raw_readl(KS8695_PCI_VA + KS8695_PBCD)); |
| } |
| |
| return PCIBIOS_SUCCESSFUL; |
| } |
| |
| static int ks8695_pci_writeconfig(struct pci_bus *bus, |
| unsigned int devfn, int where, int size, u32 value) |
| { |
| unsigned long tmp; |
| |
| if (pci_cfg_dbg) { |
| printk("write: %d,%08x,%02x,%d: %08x\n", |
| bus->number, devfn, where, size, value); |
| } |
| |
| ks8695_pci_setupconfig(bus->number, devfn, where); |
| |
| switch (size) { |
| case 4: |
| __raw_writel(value, KS8695_PCI_VA + KS8695_PBCD); |
| break; |
| case 2: |
| tmp = __raw_readl(KS8695_PCI_VA + KS8695_PBCD); |
| tmp &= ~(0xffff << ((where & 2) * 8)); |
| tmp |= value << ((where & 2) * 8); |
| |
| __raw_writel(tmp, KS8695_PCI_VA + KS8695_PBCD); |
| break; |
| case 1: |
| tmp = __raw_readl(KS8695_PCI_VA + KS8695_PBCD); |
| tmp &= ~(0xff << ((where & 3) * 8)); |
| tmp |= value << ((where & 3) * 8); |
| |
| __raw_writel(tmp, KS8695_PCI_VA + KS8695_PBCD); |
| break; |
| } |
| |
| return PCIBIOS_SUCCESSFUL; |
| } |
| |
| static void ks8695_local_writeconfig(int where, u32 value) |
| { |
| ks8695_pci_setupconfig(0, 0, where); |
| __raw_writel(value, KS8695_PCI_VA + KS8695_PBCD); |
| } |
| |
| static struct pci_ops ks8695_pci_ops = { |
| .read = ks8695_pci_readconfig, |
| .write = ks8695_pci_writeconfig, |
| }; |
| |
| static struct pci_bus *ks8695_pci_scan_bus(int nr, struct pci_sys_data *sys) |
| { |
| return pci_scan_bus(sys->busnr, &ks8695_pci_ops, sys); |
| } |
| |
| static struct resource pci_mem = { |
| .name = "PCI Memory space", |
| .start = KS8695_PCIMEM_PA, |
| .end = KS8695_PCIMEM_PA + (KS8695_PCIMEM_SIZE - 1), |
| .flags = IORESOURCE_MEM, |
| }; |
| |
| static struct resource pci_io = { |
| .name = "PCI IO space", |
| .start = KS8695_PCIIO_PA, |
| .end = KS8695_PCIIO_PA + (KS8695_PCIIO_SIZE - 1), |
| .flags = IORESOURCE_IO, |
| }; |
| |
| static int __init ks8695_pci_setup(int nr, struct pci_sys_data *sys) |
| { |
| if (nr > 0) |
| return 0; |
| |
| request_resource(&iomem_resource, &pci_mem); |
| request_resource(&ioport_resource, &pci_io); |
| |
| sys->resource[0] = &pci_io; |
| sys->resource[1] = &pci_mem; |
| sys->resource[2] = NULL; |
| |
| /* Assign and enable processor bridge */ |
| ks8695_local_writeconfig(PCI_BASE_ADDRESS_0, KS8695_PCIMEM_PA); |
| |
| /* Enable bus-master & Memory Space access */ |
| ks8695_local_writeconfig(PCI_COMMAND, PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY); |
| |
| /* Set cache-line size & latency. */ |
| ks8695_local_writeconfig(PCI_CACHE_LINE_SIZE, (32 << 8) | (L1_CACHE_BYTES / sizeof(u32))); |
| |
| /* Reserve PCI memory space for PCI-AHB resources */ |
| if (!request_mem_region(KS8695_PCIMEM_PA, SZ_64M, "PCI-AHB Bridge")) { |
| printk(KERN_ERR "Cannot allocate PCI-AHB Bridge memory.\n"); |
| return -EBUSY; |
| } |
| |
| return 1; |
| } |
| |
| static inline unsigned int size_mask(unsigned long size) |
| { |
| return (~size) + 1; |
| } |
| |
| static int ks8695_pci_fault(unsigned long addr, unsigned int fsr, struct pt_regs *regs) |
| { |
| unsigned long pc = instruction_pointer(regs); |
| unsigned long instr = *(unsigned long *)pc; |
| unsigned long cmdstat; |
| |
| cmdstat = __raw_readl(KS8695_PCI_VA + KS8695_CRCFCS); |
| |
| printk(KERN_ERR "PCI abort: address = 0x%08lx fsr = 0x%03x PC = 0x%08lx LR = 0x%08lx [%s%s%s%s%s]\n", |
| addr, fsr, regs->ARM_pc, regs->ARM_lr, |
| cmdstat & (PCI_STATUS_SIG_TARGET_ABORT << 16) ? "GenTarget" : " ", |
| cmdstat & (PCI_STATUS_REC_TARGET_ABORT << 16) ? "RecvTarget" : " ", |
| cmdstat & (PCI_STATUS_REC_MASTER_ABORT << 16) ? "MasterAbort" : " ", |
| cmdstat & (PCI_STATUS_SIG_SYSTEM_ERROR << 16) ? "SysError" : " ", |
| cmdstat & (PCI_STATUS_DETECTED_PARITY << 16) ? "Parity" : " " |
| ); |
| |
| __raw_writel(cmdstat, KS8695_PCI_VA + KS8695_CRCFCS); |
| |
| /* |
| * If the instruction being executed was a read, |
| * make it look like it read all-ones. |
| */ |
| if ((instr & 0x0c100000) == 0x04100000) { |
| int reg = (instr >> 12) & 15; |
| unsigned long val; |
| |
| if (instr & 0x00400000) |
| val = 255; |
| else |
| val = -1; |
| |
| regs->uregs[reg] = val; |
| regs->ARM_pc += 4; |
| return 0; |
| } |
| |
| if ((instr & 0x0e100090) == 0x00100090) { |
| int reg = (instr >> 12) & 15; |
| |
| regs->uregs[reg] = -1; |
| regs->ARM_pc += 4; |
| return 0; |
| } |
| |
| return 1; |
| } |
| |
| static void __init ks8695_pci_preinit(void) |
| { |
| /* stage 1 initialization, subid, subdevice = 0x0001 */ |
| __raw_writel(0x00010001, KS8695_PCI_VA + KS8695_CRCSID); |
| |
| /* stage 2 initialization */ |
| /* prefetch limits with 16 words, retry enable */ |
| __raw_writel(0x40000000, KS8695_PCI_VA + KS8695_PBCS); |
| |
| /* configure memory mapping */ |
| __raw_writel(KS8695_PCIMEM_PA, KS8695_PCI_VA + KS8695_PMBA); |
| __raw_writel(size_mask(KS8695_PCIMEM_SIZE), KS8695_PCI_VA + KS8695_PMBAM); |
| __raw_writel(KS8695_PCIMEM_PA, KS8695_PCI_VA + KS8695_PMBAT); |
| __raw_writel(0, KS8695_PCI_VA + KS8695_PMBAC); |
| |
| /* configure IO mapping */ |
| __raw_writel(KS8695_PCIIO_PA, KS8695_PCI_VA + KS8695_PIOBA); |
| __raw_writel(size_mask(KS8695_PCIIO_SIZE), KS8695_PCI_VA + KS8695_PIOBAM); |
| __raw_writel(KS8695_PCIIO_PA, KS8695_PCI_VA + KS8695_PIOBAT); |
| __raw_writel(0, KS8695_PCI_VA + KS8695_PIOBAC); |
| |
| /* hook in fault handlers */ |
| hook_fault_code(8, ks8695_pci_fault, SIGBUS, "external abort on non-linefetch"); |
| hook_fault_code(10, ks8695_pci_fault, SIGBUS, "external abort on non-linefetch"); |
| } |
| |
| static void ks8695_show_pciregs(void) |
| { |
| if (!pci_dbg) |
| return; |
| |
| printk(KERN_INFO "PCI: CRCFID = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_CRCFID)); |
| printk(KERN_INFO "PCI: CRCFCS = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_CRCFCS)); |
| printk(KERN_INFO "PCI: CRCFRV = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_CRCFRV)); |
| printk(KERN_INFO "PCI: CRCFLT = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_CRCFLT)); |
| printk(KERN_INFO "PCI: CRCBMA = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_CRCBMA)); |
| printk(KERN_INFO "PCI: CRCSID = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_CRCSID)); |
| printk(KERN_INFO "PCI: CRCFIT = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_CRCFIT)); |
| |
| printk(KERN_INFO "PCI: PBM = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_PBM)); |
| printk(KERN_INFO "PCI: PBCS = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_PBCS)); |
| |
| printk(KERN_INFO "PCI: PMBA = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_PMBA)); |
| printk(KERN_INFO "PCI: PMBAC = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_PMBAC)); |
| printk(KERN_INFO "PCI: PMBAM = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_PMBAM)); |
| printk(KERN_INFO "PCI: PMBAT = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_PMBAT)); |
| |
| printk(KERN_INFO "PCI: PIOBA = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_PIOBA)); |
| printk(KERN_INFO "PCI: PIOBAC = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_PIOBAC)); |
| printk(KERN_INFO "PCI: PIOBAM = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_PIOBAM)); |
| printk(KERN_INFO "PCI: PIOBAT = %08x\n", __raw_readl(KS8695_PCI_VA + KS8695_PIOBAT)); |
| } |
| |
| |
| static struct hw_pci ks8695_pci __initdata = { |
| .nr_controllers = 1, |
| .preinit = ks8695_pci_preinit, |
| .setup = ks8695_pci_setup, |
| .scan = ks8695_pci_scan_bus, |
| .postinit = NULL, |
| .swizzle = pci_std_swizzle, |
| .map_irq = NULL, |
| }; |
| |
| void __init ks8695_init_pci(struct ks8695_pci_cfg *cfg) |
| { |
| if (__raw_readl(KS8695_PCI_VA + KS8695_CRCFRV) & CFRV_GUEST) { |
| printk("PCI: KS8695 in guest mode, not initialising\n"); |
| return; |
| } |
| |
| printk(KERN_INFO "PCI: Initialising\n"); |
| ks8695_show_pciregs(); |
| |
| /* set Mode */ |
| __raw_writel(cfg->mode << 29, KS8695_PCI_VA + KS8695_PBM); |
| |
| ks8695_pci.map_irq = cfg->map_irq; /* board-specific map_irq method */ |
| |
| pci_common_init(&ks8695_pci); |
| } |