| #include <dt-bindings/clock/qcom,gcc-khaje.h> |
| #include <dt-bindings/msm/msm-camera.h> |
| |
| &soc { |
| cam_res_mgr_label: qcom,cam-res-mgr { |
| compatible = "qcom,cam-res-mgr"; |
| status = "ok"; |
| }; |
| }; |
| |
| &cam_cci0 { |
| actuator_rear: qcom,actuator0 { |
| cell-index = <0>; |
| compatible = "qcom,actuator"; |
| cci-master = <0>; |
| cam_vaf-supply = <&L5P>; |
| regulator-names = "cam_vaf"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <2800000>; |
| rgltr-max-voltage = <2800000>; |
| rgltr-load-current = <100000>; |
| status = "ok"; |
| }; |
| |
| actuator_rear_aux: qcom,actuator1 { |
| cell-index = <1>; |
| compatible = "qcom,actuator"; |
| cci-master = <1>; |
| cam_vaf-supply = <&L5P>; |
| regulator-names = "cam_vaf"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <2800000>; |
| rgltr-max-voltage = <2800000>; |
| rgltr-load-current = <100000>; |
| status = "ok"; |
| }; |
| |
| eeprom_rear: qcom,eeprom0 { |
| cell-index = <0>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&L7P>; |
| cam_vana-supply = <&L4P>; |
| cam_vdig-supply = <&L2P>; |
| cam_vaf-supply = <&L5P>; |
| cam_clk-supply = <&gcc_camss_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk", "cam_vaf"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2800000 1056000 0 2800000>; |
| rgltr-max-voltage = <1800000 2800000 1056000 0 2800000>; |
| rgltr-load-current = <120000 80000 1200000 0 100000>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_active |
| &cam_sensor_rear0_reset_active>; |
| pinctrl-1 = <&cam_sensor_mclk0_suspend |
| &cam_sensor_rear0_reset_suspend>; |
| gpios = <&tlmm 20 0>, |
| <&tlmm 18 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0"; |
| sensor-mode = <0>; |
| cci-master = <0>; |
| status = "ok"; |
| clocks = <&gcc GCC_CAMSS_MCLK0_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <19200000>; |
| }; |
| |
| eeprom_rear_aux: qcom,eeprom1 { |
| cell-index = <1>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&L7P>; |
| cam_vana-supply = <&L3P>; |
| cam_vdig-supply = <&L1P>; |
| cam_vaf-supply = <&L5P>; |
| cam_clk-supply = <&gcc_camss_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk", "cam_vaf"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2800000 1200000 0 2800000>; |
| rgltr-max-voltage = <1800000 2800000 1200000 0 2800000>; |
| rgltr-load-current = <120000 80000 1200000 0 100000>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk1_active |
| &cam_sensor_rear1_reset_active>; |
| pinctrl-1 = <&cam_sensor_mclk1_suspend |
| &cam_sensor_rear1_reset_suspend>; |
| gpios = <&tlmm 21 0>, |
| <&tlmm 19 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK1", |
| "CAM_RESET1"; |
| sensor-mode = <0>; |
| cci-master = <1>; |
| status = "ok"; |
| clocks = <&gcc GCC_CAMSS_MCLK1_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <19200000>; |
| }; |
| |
| eeprom_front: qcom,eeprom2 { |
| cell-index = <2>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&L7P>; |
| cam_vana-supply = <&L6P>; |
| cam_vdig-supply = <&L2P>; |
| cam_clk-supply = <&gcc_camss_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2800000 1056000 0>; |
| rgltr-max-voltage = <1800000 2800000 1056000 0>; |
| rgltr-load-current = <0 80000 105000 0>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_active |
| &cam_sensor_front0_reset_active>; |
| pinctrl-1 = <&cam_sensor_mclk2_suspend |
| &cam_sensor_front0_reset_suspend>; |
| gpios = <&tlmm 27 0>, |
| <&tlmm 24 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2"; |
| sensor-mode = <0>; |
| cci-master = <1>; |
| status = "ok"; |
| clocks = <&gcc GCC_CAMSS_MCLK2_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <24000000>; |
| }; |
| |
| eeprom_rear_aux2: qcom,eeprom3 { |
| cell-index = <3>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&L7P>; |
| cam_vana-supply = <&L6P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&gcc_camss_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2800000 1200000 0>; |
| rgltr-max-voltage = <1800000 2800000 1200000 0>; |
| rgltr-load-current = <120000 80000 1200000 0>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk3_active |
| &cam_sensor_rear2_reset_active>; |
| pinctrl-1 = <&cam_sensor_mclk3_suspend |
| &cam_sensor_rear2_reset_suspend>; |
| gpios = <&tlmm 28 0>, |
| <&tlmm 65 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK3", |
| "CAM_RESET3"; |
| sensor-mode = <0>; |
| cci-master = <0>; |
| status = "ok"; |
| clocks = <&gcc GCC_CAMSS_MCLK3_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <19200000>; |
| }; |
| |
| led_flash_rear: qcom,camera-flash@0 { |
| cell-index = <0>; |
| compatible = "qcom,camera-flash"; |
| cci-master = <1>; |
| flash-type = <CAM_FLASH_TYPE_I2C>; |
| cam_vio-supply = <&L7P>; |
| regulator-names = "cam_vio"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <1800000>; |
| rgltr-max-voltage = <1800000>; |
| rgltr-load-current = <120000>; |
| gpio-no-mux = <0>; |
| gpio-custom1 = <0>; |
| gpio-req-tbl-num = <0>; |
| gpio-req-tbl-flags = <0>; |
| gpio-req-tbl-label = "CUSTOM_GPIO1"; |
| status = "ok"; |
| }; |
| |
| led_flash_rear_aux: qcom,camera-flash@1 { |
| cell-index = <1>; |
| compatible = "qcom,camera-flash"; |
| cci-master = <1>; |
| flash-type = <CAM_FLASH_TYPE_I2C>; |
| cam_vio-supply = <&L7P>; |
| regulator-names = "cam_vio"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <1800000>; |
| rgltr-max-voltage = <1800000>; |
| rgltr-load-current = <120000>; |
| gpio-no-mux = <0>; |
| gpio-custom1 = <0>; |
| gpio-req-tbl-num = <0>; |
| gpio-req-tbl-flags = <0>; |
| gpio-req-tbl-label = "CUSTOM_GPIO1"; |
| status = "ok"; |
| }; |
| |
| led_flash_rear_aux2: qcom,camera-flash@2 { |
| cell-index = <2>; |
| compatible = "qcom,camera-flash"; |
| cci-master = <1>; |
| flash-type = <CAM_FLASH_TYPE_I2C>; |
| cam_vio-supply = <&L7P>; |
| regulator-names = "cam_vio"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <1800000>; |
| rgltr-max-voltage = <1800000>; |
| rgltr-load-current = <120000>; |
| gpio-no-mux = <0>; |
| gpio-custom1 = <0>; |
| gpio-req-tbl-num = <0>; |
| gpio-req-tbl-flags = <0>; |
| gpio-req-tbl-label = "CUSTOM_GPIO1"; |
| status = "ok"; |
| }; |
| |
| /* Rear*/ |
| qcom,cam-sensor0 { |
| cell-index = <0>; |
| compatible = "qcom,cam-sensor"; |
| csiphy-sd-index = <0>; |
| sensor-position-roll = <270>; |
| sensor-position-pitch = <0>; |
| sensor-position-yaw = <180>; |
| actuator-src = <&actuator_rear>; |
| led-flash-src = <&led_flash_rear>; |
| eeprom-src = <&eeprom_rear>; |
| cam_vio-supply = <&L7P>; |
| cam_vana-supply = <&L4P>; |
| cam_vdig-supply = <&L2P>; |
| cam_clk-supply = <&gcc_camss_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2800000 1056000 0>; |
| rgltr-max-voltage = <1800000 2800000 1056000 0>; |
| rgltr-load-current = <120000 80000 1200000 0>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_active |
| &cam_sensor_rear0_reset_active>; |
| pinctrl-1 = <&cam_sensor_mclk0_suspend |
| &cam_sensor_rear0_reset_suspend>; |
| gpios = <&tlmm 20 0>, |
| <&tlmm 18 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0"; |
| sensor-mode = <0>; |
| cci-master = <0>; |
| status = "ok"; |
| clocks = <&gcc GCC_CAMSS_MCLK0_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <19200000>; |
| }; |
| |
| /*Rear Aux*/ |
| qcom,cam-sensor1 { |
| cell-index = <1>; |
| compatible = "qcom,cam-sensor"; |
| csiphy-sd-index = <1>; |
| sensor-position-roll = <270>; |
| sensor-position-pitch = <0>; |
| sensor-position-yaw = <180>; |
| actuator-src = <&actuator_rear_aux>; |
| led-flash-src = <&led_flash_rear_aux>; |
| eeprom-src = <&eeprom_rear_aux>; |
| cam_vio-supply = <&L7P>; |
| cam_vana-supply = <&L3P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&gcc_camss_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2800000 1200000 0>; |
| rgltr-max-voltage = <1800000 2800000 1200000 0>; |
| rgltr-load-current = <120000 80000 1200000 0>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk1_active |
| &cam_sensor_rear1_reset_active>; |
| pinctrl-1 = <&cam_sensor_mclk1_suspend |
| &cam_sensor_rear1_reset_suspend>; |
| gpios = <&tlmm 21 0>, |
| <&tlmm 19 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK1", |
| "CAM_RESET1"; |
| sensor-mode = <0>; |
| cci-master = <1>; |
| status = "ok"; |
| clocks = <&gcc GCC_CAMSS_MCLK1_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <19200000>; |
| }; |
| |
| /*Front*/ |
| qcom,cam-sensor2 { |
| cell-index = <2>; |
| compatible = "qcom,cam-sensor"; |
| csiphy-sd-index = <2>; |
| sensor-position-roll = <270>; |
| sensor-position-pitch = <0>; |
| sensor-position-yaw = <0>; |
| eeprom-src = <&eeprom_front>; |
| cam_vio-supply = <&L7P>; |
| cam_vana-supply = <&L6P>; |
| cam_vdig-supply = <&L2P>; |
| cam_clk-supply = <&gcc_camss_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2800000 1056000 0>; |
| rgltr-max-voltage = <1800000 2800000 1056000 0>; |
| rgltr-load-current = <0 80000 105000 0>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_active |
| &cam_sensor_front0_reset_active |
| &cam_sensor_csi_mux_oe_active |
| &cam_sensor_csi_mux_sel_active>; |
| pinctrl-1 = <&cam_sensor_mclk2_suspend |
| &cam_sensor_front0_reset_suspend |
| &cam_sensor_csi_mux_oe_suspend |
| &cam_sensor_csi_mux_sel_suspend>; |
| gpios = <&tlmm 27 0>, |
| <&tlmm 24 0>, |
| <&tlmm 66 0>, |
| <&tlmm 67 0>; |
| gpio-reset = <1>; |
| gpio-custom1 = <2>; |
| gpio-custom2 = <3>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2", |
| "CAM_CSIMUX_OE0", |
| "CAM_CSIMUX_SEL0"; |
| sensor-mode = <0>; |
| cci-master = <1>; |
| status = "ok"; |
| clocks = <&gcc GCC_CAMSS_MCLK2_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <24000000>; |
| }; |
| |
| /*Rear Aux2*/ |
| qcom,cam-sensor3 { |
| cell-index = <3>; |
| compatible = "qcom,cam-sensor"; |
| csiphy-sd-index = <2>; |
| sensor-position-roll = <270>; |
| sensor-position-pitch = <0>; |
| sensor-position-yaw = <180>; |
| led-flash-src = <&led_flash_rear_aux2>; |
| eeprom-src = <&eeprom_rear_aux2>; |
| cam_vio-supply = <&L7P>; |
| cam_vana-supply = <&L6P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&gcc_camss_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2800000 1200000 0>; |
| rgltr-max-voltage = <1800000 2800000 1200000 0>; |
| rgltr-load-current = <120000 80000 1200000 0>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk3_active |
| &cam_sensor_rear2_reset_active |
| &cam_sensor_csi_mux_oe_active |
| &cam_sensor_csi_mux_sel_active>; |
| pinctrl-1 = <&cam_sensor_mclk3_suspend |
| &cam_sensor_rear2_reset_suspend |
| &cam_sensor_csi_mux_oe_suspend |
| &cam_sensor_csi_mux_sel_suspend>; |
| gpios = <&tlmm 28 0>, |
| <&tlmm 65 0>, |
| <&tlmm 66 0>, |
| <&tlmm 67 0>; |
| gpio-reset = <1>; |
| gpio-custom1 = <2>; |
| gpio-custom2 = <3>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK3", |
| "CAM_RESET3", |
| "CAM_CSIMUX_OE1", |
| "CAM_CSIMUX_SEL1"; |
| sensor-mode = <0>; |
| cci-master = <0>; |
| status = "ok"; |
| clocks = <&gcc GCC_CAMSS_MCLK3_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <19200000>; |
| }; |
| }; |