#include "lagoon-mtp.dtsi"
#include "dsi-panel-ft8716u-1080p-video.dtsi"

&mtp_batterydata {
    #include "qg-batterydata-n10-veken-4360mah.dtsi"
};


&pm7250b_charger {
    /delete-property/ qcom,fcc-stepping-enable;
    status = "ok";
    io-channels = <&pm7250b_vadc ADC_USB_IN_V_16>,
                  <&pm7250b_vadc ADC_USB_IN_I>,
                  <&pm7250b_vadc ADC_CHG_TEMP>,
                  <&pm7250b_vadc ADC_DIE_TEMP>,
                  <&pm7250b_vadc ADC_AMUX_THM3_PU2>,
                  <&pm7250b_vadc ADC_SBUx>,
                  <&pm7250b_vadc ADC_VPH_PWR>,
                  <&pm7250b_vadc ADC_AMUX_THM1_PU2>,
                  <&pm7250b_vadc ADC_INT_EXT_ISENSE_VBAT_VDATA>;
    io-channel-names = "usb_in_voltage",
                       "usb_in_current",
                       "chg_temp",
                       "die_temp",
                       "conn_temp",
                       "sbux_res",
                       "vph_voltage",
                       "skin_temp",
                       "v_i_int_ext";
    qcom,battery-data = <&mtp_batterydata>;
    qcom,fv-max-uv = <4400000>;
    qcom,fcc-max-ua = <3500000>;
    qcom,otg-cl-ua = <1500000>;
    qcom,wls-current-max-ua = <1300000>;
    qcom,hvdcp2-max-icl-ua = <2000000>;
    qcom,hvdcp3-max-icl-ua = <2200000>;
    qcom,qc4-max-icl-ua = <2050000>;
    qcom,chg-term-src = <1>;
    qcom,chg-term-current-ma = <(-150)>;
    qcom,sec-charger-config = <1>;
    qcom,step-charging-enable;
    qcom,sw-jeita-enable;
    qcom,lpd-disable;
    qcom,thermal-mitigation = <2000000 2000000 2000000 2000000
                               1500000 1000000 500000>;
    qcom,thermal-mitigation-lcdon = <2000000 2000000 2000000 2000000
                               1500000 1000000 500000>;
    qcom,disable-suspend-on-collapse;
    qcom,charger-temp-max = <800>;
    qcom,smb-temp-max = <800>;
    qcom,float-option = <2>;
    qcom,auto-recharge-soc = <99>;
    qcom,suspend-input-on-debug-batt;
    //qcom,en-skin-therm-mitigation;
    qcom,smb-internal-pull-kohm = <0>;
    qcom,hvdcp-disable;//zxzadd because vbus have ovp ic ,if over 6v vbus will be cut off
};

&pm7250b_qg {
    status = "ok";
    io-channels = <&pm7250b_vadc ADC_BAT_THERM_PU1>,
                  <&pm7250b_vadc ADC_BAT_ID_PU2>;
    qcom,battery-data = <&mtp_batterydata>;
    qcom,vbatt-empty-mv = <3200>;
    qcom,vbatt-low-mv = <3500>;
    qcom,vbatt-cutoff-mv = <3400>;
    qcom,fvss-vbatt-mv = <3500>;
    qcom,qg-iterm-ma = <350>;
    qcom,ignore-shutdown-soc-secs = <604800>;
    qcom,shutdown-temp-diff = <150>;
    qcom,shutdown_soc_threshold = <50>;
    qcom,hold-soc-while-full;
    qcom,linearize-soc;
    //qcom,rbat-conn-mohm = <35>;
    qcom,use-cp-iin-sns;
};

&smb1396_div2_cp_master {
    qcom,max-cutoff-soc = <85>;
};

&smb1396_slave {
    status = "disabled";
};

&smb1396_div2_cp_slave {
    status = "disabled";
};

&eud {
    status = "disabled";
};

&usb_qmp_dp_phy {
    status = "disabled";
};

&pm7250b_pdphy {
    qcom,default-sink-caps = <5000 2000>, /* 5V @ 2A */
                             <9000 1500>, /* 9V @ 1.5A */
                             <10000 1500>; /* 10V @ 1.5A */
};

&usb0 {
    extcon = <&pm7250b_pdphy>, <&pm7250b_charger>;
    dwc3@a600000 {
        maximum-speed = "high-speed";
        usb-phy = <&qusb_phy0>, <&usb_nop_phy>;
    };
};

&qusb_phy0 {
	qcom,qusb-phy-init-seq =
		/* <value reg_offset> */
		<0x23 0x210 /* PWR_CTRL1 */
		 0x03 0x04  /* PLL_ANALOG_CONTROLS_TWO */
		 0x7c 0x18c /* PLL_CLOCK_INVERTERS */
		 0x80 0x2c  /* PLL_CMODE */
		 0x0a 0x184 /* PLL_LOCK_DELAY */
		 0x19 0xb4  /* PLL_DIGITAL_TIMERS_TWO */
		 0x40 0x194 /* PLL_BIAS_CONTROL_1 */
		 0x16 0x198 /* PLL_BIAS_CONTROL_2 */
		 0x21 0x214 /* PWR_CTRL2 */
		 0x08 0x220 /* IMP_CTRL1 */
		 0x58 0x224 /* IMP_CTRL2 */
		 0x47 0x240 /* TUNE1 */
		 0x29 0x244 /* TUNE2 */
		 0xca 0x248 /* TUNE3 */
		 0x04 0x24c /* TUNE4 */
		 0x03 0x250 /* TUNE5 */
		 0x30 0x23c /* CHG_CTRL2 */
		 0x22 0x210>; /* PWR_CTRL1 */

	qcom,qusb-phy-host-init-seq =
		/* <value reg_offset> */
		<0x23 0x210 /* PWR_CTRL1 */
		0x03 0x04  /* PLL_ANALOG_CONTROLS_TWO */
		0x7c 0x18c /* PLL_CLOCK_INVERTERS */
		0x80 0x2c  /* PLL_CMODE */
		0x0a 0x184 /* PLL_LOCK_DELAY */
		0x19 0xb4  /* PLL_DIGITAL_TIMERS_TWO */
		0x40 0x194 /* PLL_BIAS_CONTROL_1 */
		0x16 0x198 /* PLL_BIAS_CONTROL_2 */
		0x21 0x214 /* PWR_CTRL2 */
		0x08 0x220 /* IMP_CTRL1 */
		0x58 0x224 /* IMP_CTRL2 */
		0x47 0x240 /* TUNE1 */
		0x29 0x244 /* TUNE2 */
		0xca 0x248 /* TUNE3 */
		0x04 0x24c /* TUNE4 */
		0x03 0x250 /* TUNE5 */
		0x30 0x23c /* CHG_CTRL2 */
		0x22 0x210>; /* PWR_CTRL1 */
};

&pm6150l_wled {
	qcom,string-cfg = <3>;
	qcom,fs-current-limit = <20000>;
	status = "okay";
};

&pm6150l_lcdb {
	status = "okay";
};

&pm6150a_amoled {
 	status = "disabled";
};
&dsi_ft8716u_1080_video {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
	qcom,mdss-dsi-bl-min-level = <1>;
	qcom,mdss-dsi-bl-max-level = <4095>;
	qcom,mdss-brightness-max-level = <255>;
	qcom,mdss-brightness-default-level = <167>;
	qcom,platform-te-gpio = <&tlmm 23 0>;
	qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
		qcom,mdss-dsi-t-clk-post = <0x0e>;
		qcom,mdss-dsi-t-clk-pre = <0x35>;
	qcom,mdss-dsi-display-timings {
		timing@0 {
		qcom,mdss-dsi-panel-phy-timings = [00 1C 07 07 23 21 07 07 05 03 04 00];
        	qcom,display-topology = <1 0 1>;
		qcom,default-topology-index = <0>;
		};
	};
};


&sde_dsi {
	lab-supply = <&lcdb_ldo_vreg>;
	ibb-supply = <&lcdb_ncp_vreg>;
	qcom,dsi-default-panel = <&dsi_ft8716u_1080_video>;
};


&qupv3_se8_i2c {

	qcom,i2c-touch-active = "focaltech,fts";
	status = "okay";
	synaptics_tcm@20 {
		status = "disabled";
	};

        focaltech@38 {
		compatible = "focaltech,fts";
		reg = <0x38>;
		interrupt-parent = <&tlmm>;
		interrupts = <22 0x02>;
		focaltech,reset-gpio = <&tlmm 21 0x01>;
		focaltech,irq-gpio = <&tlmm 22 0x02>;
		//vcc_i2c-supply = <&L11A>;
	        //vdd-supply = <&L6A>;
                //focaltech,irq-on-state = <0>;
		focaltech,max-touch-number = <10>;
		focaltech,display-coords =  <0 0 1080 1920>;
		//focaltech,have-key;
		//focaltech,key-number = <3>;
		focaltech,keys = <139 102 158>;
		focaltech,key-y-coord = <2000>;
		focaltech,key-x-coords = <200 600 800>;
	        //pinctrl-0 = <&ts_int_active &ts_reset_active>;
		//pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
		//pinctrl-2 = <&ts_release>;
                //focaltech,i2c-pull-up;

		panel = <&dsi_ft8716u_1080_video>;

           };
};

&lagoon_snd {
	qcom,model = "lito-lagoon-n10-snd-card";
	qcom,msm-mi2s-master = <1>, <1>, <1>, <1>, <1>, <1>;
	qcom,wcn-btfm = <1>;
	qcom,ext-disp-audio-rx = <0>;
	qcom,audio-routing =
		"AMIC1", "MIC BIAS1",
		"MIC BIAS1", "Analog Mic1",
		"AMIC2", "MIC BIAS2",
		"MIC BIAS2", "Analog Mic2",
		"AMIC3", "MIC BIAS1",
		"MIC BIAS1", "Analog Mic3",
		"AMIC4", "MIC BIAS1",
		"MIC BIAS1", "Analog Mic4",
		"TX DMIC0", "MIC BIAS1",
		"IN1_HPHL", "HPHL_OUT",
		"IN2_HPHR", "HPHR_OUT",
		"IN3_AUX", "AUX_OUT",
		"TX SWR_ADC0", "ADC1_OUTPUT",
		"TX SWR_ADC2", "ADC2_OUTPUT",
		"TX SWR_ADC3", "ADC3_OUTPUT",
		"RX_TX DEC0_INP", "TX DEC0 MUX",
		"RX_TX DEC1_INP", "TX DEC1 MUX",
		"RX_TX DEC2_INP", "TX DEC2 MUX",
		"RX_TX DEC3_INP", "TX DEC3 MUX",
		"VA_AIF1 CAP", "VA_SWR_CLK",
		"VA_AIF2 CAP", "VA_SWR_CLK",
		"VA_AIF3 CAP", "VA_SWR_CLK",
		"VA SWR_ADC0", "VA_SWR_CLK",
		"VA SWR_ADC1", "VA_SWR_CLK",
		"VA SWR_ADC2", "VA_SWR_CLK",
		"VA SWR_ADC3", "VA_SWR_CLK",
		"VA SWR_ADC0", "ADC1_OUTPUT",
		"VA SWR_ADC2", "ADC2_OUTPUT",
		"VA SWR_ADC3", "ADC3_OUTPUT";
	qcom,msm-mbhc-hphl-swh = <1>;
	qcom,msm-mbhc-gnd-swh = <1>;
	/delete-property/ qcom,cdc-dmic01-gpios;
	/delete-property/ qcom,cdc-dmic23-gpios;
	/delete-property/ qcom,cdc-dmic45-gpios;
	asoc-codec  = <&stub_codec>, <&bolero>;
	asoc-codec-names = "msm-stub-codec.1", "bolero_codec";
	qcom,wsa-max-devs = <0>;
	/delete-property/ qcom,wsa-devs;
	/delete-property/ qcom,wsa-aux-dev-prefix;
	qcom,codec-max-aux-devs = <1>;
	qcom,codec-aux-devs = <&wcd937x_codec>;
	qcom,msm_audio_ssr_devs = <&audio_apr>, <&q6core>,
				  <&lpi_tlmm>, <&bolero>;
};
&wcd937x_codec{
    status = "ok";
};
&wcd938x_codec{
    status = "disabled";
};
&wcd937x_rx_slave {
	status = "ok";
};

&wcd937x_tx_slave {
	status = "ok";
};

&wcd938x_tx_slave {
	status = "disabled";
};

&wcd938x_rx_slave {
	status = "disabled";
};
&cdc_dmic01_gpios{
    status = "disabled";
};

&cdc_dmic23_gpios{
    status = "disabled";
};
&cdc_dmic45_gpios{
    status = "disabled";
};
&wsa883x_0221{
    status = "disabled";
};
&wsa883x_0222{
    status = "disabled";
};

/*aw881xx I2c is used gpio0 &gpio1 same as nfc in lagoon-pinctrl.dtsi */
&qupv3_se0_i2c {
	status = "ok";
	#address-cells = <1>;
	#size-cells = <0>;

    aw881xx_smartpa@34{
        compatible = "awinic,aw881xx_smartpa";
        reg = <0x43>;/*Virtual address, real address is 0x34*/
        reset-gpio = <&tlmm 10 0>;
        irq-gpio = <&tlmm 11 0>;
        monitor-flag = <1>;
        monitor-timer-val = <30000>;
        status = "okay";
    };
};
&dai_mi2s4 {
    pinctrl-names = "default", "sleep";
    pinctrl-0 = <&lpi_i2s1_sck_active &lpi_i2s1_ws_active
                 &lpi_i2s1_sd0_active &lpi_i2s1_sd1_active>;
    pinctrl-1 = <&lpi_i2s1_sck_sleep  &lpi_i2s1_ws_sleep
                 &lpi_i2s1_sd0_sleep  &lpi_i2s1_sd1_sleep>;
};

&tlmm {
	bq27541_hdq_active: bq27541_hdq_active{
		mux {
			pins = "gpio33";
			function = "gpio";
		};
		config {
			pins = "gpio33";
			drive-strength = <2>;
			bias-pull-up;
		};
	};
};

&soc {
	bq27541 {
		compatible = "qcom,bq27541-fuel-hdq";
		qcom,hdq-gpio = <&tlmm 33 0>;
		pinctrl-names = "bq27541_hdq";
		pinctrl-0 = <&bq27541_hdq_active>;
		};
};