| #include "scuba-audio-overlay.dtsi" |
| #include "scuba-thermal-overlay.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| #include "scuba-sde-display.dtsi" |
| #include "camera/scuba-camera-sensor-idp.dtsi" |
| |
| &soc { |
| scuba_batterydata: qcom,battery-data { |
| qcom,batt-id-range-pct = <15>; |
| #include "qg-batterydata-alium-3600mah.dtsi" |
| #include "qg-batterydata-atl466271_3300mAh.dtsi" |
| }; |
| }; |
| |
| &pm2250_qg { |
| qcom,battery-data = <&scuba_batterydata>; |
| qcom,qg-iterm-ma = <150>; |
| qcom,hold-soc-while-full; |
| qcom,linearize-soc; |
| qcom,cl-feedback-on; |
| qcom,tcss-enable; |
| qcom,fvss-enable; |
| qcom,fvss-vbatt-mv = <3500>; |
| qcom,bass-enable; |
| }; |
| |
| &sdhc_1 { |
| vdd-supply = <&L20A>; |
| qcom,vdd-voltage-level = <2856000 2856000>; |
| qcom,vdd-current-level = <0 570000>; |
| |
| vdd-io-supply = <&L14A>; |
| qcom,vdd-io-always-on; |
| qcom,vdd-io-lpm-sup; |
| qcom,vdd-io-voltage-level = <1800000 1800000>; |
| qcom,vdd-io-current-level = <0 325000>; |
| |
| pinctrl-names = "active", "sleep"; |
| pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on |
| &sdc1_rclk_on>; |
| pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off |
| &sdc1_rclk_off>; |
| |
| status = "ok"; |
| }; |
| |
| &scuba_snd { |
| qcom,model = "bengal-scubaqrd-snd-card"; |
| qcom,msm-mi2s-master = <1>, <1>, <1>, <1>; |
| qcom,wcn-btfm = <1>; |
| qcom,ext-disp-audio-rx = <0>; |
| qcom,audio-routing = |
| "AMIC1", "MIC BIAS1", |
| "MIC BIAS1", "Analog Mic1", |
| "AMIC2", "MIC BIAS2", |
| "MIC BIAS2", "Analog Mic2", |
| "AMIC3", "MIC BIAS3", |
| "MIC BIAS3", "Analog Mic3", |
| "AMIC4", "MIC BIAS3", |
| "MIC BIAS3", "Analog Mic4", |
| "IN1_HPHL", "HPHL_OUT", |
| "IN2_HPHR", "HPHR_OUT", |
| "IN3_AUX", "AUX_OUT", |
| "SpkrMono WSA_IN", "AUX", |
| "TX SWR_MIC0", "ADC1_OUTPUT", |
| "TX SWR_MIC1", "ADC2_OUTPUT", |
| "TX SWR_MIC5", "ADC3_OUTPUT", |
| "TX SWR_MIC0", "VA_TX_SWR_CLK", |
| "TX SWR_MIC1", "VA_TX_SWR_CLK", |
| "TX SWR_MIC2", "VA_TX_SWR_CLK", |
| "TX SWR_MIC3", "VA_TX_SWR_CLK", |
| "TX SWR_MIC4", "VA_TX_SWR_CLK", |
| "TX SWR_MIC5", "VA_TX_SWR_CLK", |
| "TX SWR_MIC6", "VA_TX_SWR_CLK", |
| "TX SWR_MIC7", "VA_TX_SWR_CLK", |
| "TX SWR_MIC8", "VA_TX_SWR_CLK", |
| "TX SWR_MIC9", "VA_TX_SWR_CLK", |
| "TX SWR_MIC10", "VA_TX_SWR_CLK", |
| "TX SWR_MIC11", "VA_TX_SWR_CLK", |
| "RX_TX DEC0_INP", "TX DEC0 MUX", |
| "RX_TX DEC1_INP", "TX DEC1 MUX", |
| "RX_TX DEC2_INP", "TX DEC2 MUX", |
| "RX_TX DEC3_INP", "TX DEC3 MUX", |
| "TX_AIF1 CAP", "VA_TX_SWR_CLK", |
| "TX_AIF2 CAP", "VA_TX_SWR_CLK", |
| "TX_AIF3 CAP", "VA_TX_SWR_CLK", |
| "VA SWR_MIC0", "ADC1_OUTPUT", |
| "VA SWR_MIC1", "ADC2_OUTPUT", |
| "VA SWR_MIC5", "ADC3_OUTPUT"; |
| qcom,msm-mbhc-hphl-swh = <1>; |
| qcom,msm-mbhc-gnd-swh = <1>; |
| asoc-codec = <&stub_codec>, <&bolero>; |
| asoc-codec-names = "msm-stub-codec.1", "bolero_codec"; |
| qcom,wsa-max-devs = <1>; |
| qcom,wsa-devs = <&wsa881x_i2c_e>; |
| qcom,wsa-aux-dev-prefix = "SpkrMono"; |
| qcom,codec-max-aux-devs = <1>; |
| qcom,codec-aux-devs = <&rouleur_codec>; |
| qcom,msm_audio_ssr_devs = <&audio_apr>, <&q6core>, <&bolero>, |
| <&lpi_tlmm>; |
| }; |
| |
| &sdhc_2 { |
| vdd-supply = <&L21A>; |
| qcom,vdd-voltage-level = <2960000 3300000>; |
| qcom,vdd-current-level = <0 800000>; |
| |
| vdd-io-supply = <&L4A>; |
| qcom,vdd-io-voltage-level = <1800000 2960000>; |
| qcom,vdd-io-current-level = <0 22000>; |
| |
| pinctrl-names = "active", "sleep"; |
| pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; |
| pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; |
| |
| cd-gpios = <&tlmm 88 GPIO_ACTIVE_HIGH>; |
| |
| status = "ok"; |
| }; |
| |
| &pm2250_charger { |
| qcom,auto-recharge-soc = <98>; |
| qcom,suspend-input-on-debug-batt; |
| qcom,battery-data = <&scuba_batterydata>; |
| io-channels = <&pm2250_vadc ADC_USB_IN_V_16>, |
| <&pm2250_vadc ADC_CHG_TEMP>; |
| io-channel-names = "usb_in_voltage", |
| "chg_temp"; |
| qcom,thermal-mitigation = <2000000 1500000 1000000 500000>; |
| }; |
| |
| &pm2250_pwm3 { |
| status = "ok"; |
| }; |
| |
| &thermal_zones { |
| quiet-therm-usr { |
| polling-delay = <5000>; |
| }; |
| |
| quiet-therm-step { |
| polling-delay-passive = <2000>; |
| polling-delay = <5000>; |
| thermal-governor = "step_wise"; |
| thermal-sensors = <&pm2250_adc_tm_iio ADC_AMUX_THM2_PU2>; |
| wake-capable-sensor; |
| trips { |
| quiet_modem_trip0: quiet-modem-trip0 { |
| temperature = <40000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| quiet_batt_trip0: quiet-batt-trip0 { |
| temperature = <41000>; |
| hysteresis = <3000>; |
| type = "passive"; |
| }; |
| |
| quiet_modem_trip1: quiet-modem-trip1 { |
| temperature = <42000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| quiet_batt_trip1: quiet-batt-trip1 { |
| temperature = <43000>; |
| hysteresis = <4000>; |
| type = "passive"; |
| }; |
| |
| quiet_modem_trip2: quiet-modem-trip2 { |
| temperature = <43000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| quiet_cpu0_trip: quiet-cpu0-trip { |
| temperature = <44000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| quiet_batt_trip2: quiet-batt-trip2 { |
| temperature = <45000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| quiet_gpu_trip: quiet-gpu-trip { |
| temperature = <46000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| quiet_batt_trip3: quiet-batt-trip3 { |
| temperature = <47000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| quiet_modem_trip3: quiet-modem-trip3 { |
| temperature = <50000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| }; |
| |
| cooling-maps { |
| gpu-cdev { |
| trip = <&quiet_gpu_trip>; |
| /* throttle from fmax to 921600000Hz */ |
| cooling-device = <&msm_gpu THERMAL_NO_LIMIT |
| (THERMAL_MAX_LIMIT - 4)>; |
| }; |
| |
| cpu0-cdev { |
| trip = <&quiet_cpu0_trip>; |
| /* throttle from fmax to 1420800KHz */ |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT |
| (THERMAL_MAX_LIMIT - 5)>; |
| }; |
| |
| modem-proc-cdev0 { |
| trip = <&quiet_modem_trip0>; |
| cooling-device = <&modem_proc 1 1>; |
| }; |
| |
| modem-proc-cdev1 { |
| trip = <&quiet_modem_trip3>; |
| cooling-device = <&modem_proc 3 3>; |
| }; |
| |
| modem-pa-cdev0 { |
| trip = <&quiet_modem_trip1>; |
| cooling-device = <&modem_pa 1 1>; |
| }; |
| |
| modem-pa-cdev1 { |
| trip = <&quiet_modem_trip2>; |
| cooling-device = <&modem_pa 2 2>; |
| }; |
| |
| modem-pa-cdev3 { |
| trip = <&quiet_modem_trip3>; |
| cooling-device = <&modem_pa 3 3>; |
| }; |
| |
| batt-cdev0 { |
| trip = <&quiet_batt_trip0>; |
| cooling-device = <&pm2250_charger 1 1>; |
| }; |
| |
| batt-cdev1 { |
| trip = <&quiet_batt_trip1>; |
| cooling-device = <&pm2250_charger 2 2>; |
| }; |
| |
| batt-cdev2 { |
| trip = <&quiet_batt_trip2>; |
| cooling-device = <&pm2250_charger 3 3>; |
| }; |
| |
| batt-cdev3 { |
| trip = <&quiet_batt_trip3>; |
| cooling-device = <&pm2250_charger 4 4>; |
| }; |
| }; |
| }; |
| }; |
| |
| &dsi_nt36525_truly_video { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_pwm"; |
| pwms = <&pm2250_pwm3 0 0>; |
| qcom,bl-pmic-pwm-period-usecs = <100>; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <4095>; |
| qcom,platform-reset-gpio = <&tlmm 82 0>; |
| qcom,platform-reset-gpio-always-on; |
| qcom,platform-en-gpio = <&tlmm 105 0>; |
| }; |
| |
| &sde_dsi { |
| qcom,dsi-default-panel = <&dsi_nt36525_truly_video>; |
| }; |
| |
| &qupv3_se2_i2c { |
| status = "ok"; |
| qcom,i2c-touch-active = "novatek,NVT-ts"; |
| |
| novatek@62 { |
| compatible = "novatek,NVT-ts"; |
| reg = <0x62>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <80 0x2008>; |
| pinctrl-names = "pmx_ts_active","pmx_ts_suspend", |
| "pmx_ts_release"; |
| pinctrl-0 = <&ts_int_active &ts_reset_active>; |
| pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>; |
| pinctrl-2 = <&ts_release>; |
| |
| novatek,reset-gpio = <&tlmm 71 0x00>; |
| novatek,irq-gpio = <&tlmm 80 0x2008>; |
| |
| panel = <&dsi_nt36525_truly_video>; |
| }; |
| }; |
| |
| &qusb_phy0 { |
| extcon = <&pm2250_charger>; |
| |
| qcom,qusb-phy-init-seq = <0xf8 0x80 |
| 0xb3 0x84 |
| 0x83 0x88 |
| 0xc5 0x8c |
| 0x30 0x08 |
| 0x79 0x0c |
| 0x21 0x10 |
| 0x14 0x9c |
| 0x80 0x04 |
| 0x9f 0x1c |
| 0x00 0x18>; |
| }; |
| |
| &usb0 { |
| extcon = <&qusb_phy0>, <&eud>; |
| }; |
| |
| &qupv3_se1_i2c { |
| status = "ok"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| nq@28 { |
| compatible = "qcom,nq-nci"; |
| reg = <0x28>; |
| qcom,nq-irq = <&tlmm 70 0x00>; |
| qcom,nq-ven = <&tlmm 69 0x00>; |
| qcom,nq-firm = <&tlmm 31 0x00>; |
| qcom,nq-clkreq = <&tlmm 86 0x00>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <70 0>; |
| interrupt-names = "nfc_irq"; |
| pinctrl-names = "nfc_active", "nfc_suspend"; |
| pinctrl-0 = <&nfc_int_active &nfc_enable_active |
| &nfc_clk_req_active>; |
| pinctrl-1 = <&nfc_int_suspend &nfc_enable_suspend |
| &nfc_clk_req_suspend>; |
| }; |
| }; |
| |
| &tlmm { |
| fpc_reset_int: fpc_reset_int { |
| fpc_reset_low: reset_low { |
| mux { |
| pins = "gpio104"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio104"; |
| drive-strength = <2>; |
| bias-disable; |
| output-low; |
| }; |
| }; |
| |
| fpc_reset_high: reset_high { |
| mux { |
| pins = "gpio104"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio104"; |
| drive-strength = <2>; |
| bias-disable; |
| output-high; |
| }; |
| }; |
| |
| fpc_int_low: int_low { |
| mux { |
| pins = "gpio97"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio97"; |
| drive-strength = <2>; |
| bias-pull-down; |
| input-enable; |
| }; |
| }; |
| }; |
| }; |
| |
| &soc { |
| fingerprint: fpc1020 { |
| compatible = "fpc,fpc1020"; |
| interrupt-parent = <&tlmm>; |
| interrupts = <97 0>; |
| fpc,gpio_rst = <&tlmm 104 0>; |
| fpc,gpio_irq = <&tlmm 97 0>; |
| fpc,enable-on-boot; |
| pinctrl-names = "fpc1020_reset_reset", |
| "fpc1020_reset_active", |
| "fpc1020_irq_active"; |
| pinctrl-0 = <&fpc_reset_low>; |
| pinctrl-1 = <&fpc_reset_high>; |
| pinctrl-2 = <&fpc_int_low>; |
| }; |
| }; |