#include "scuba-audio-overlay.dtsi"
#include "scuba-thermal-overlay.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include "scuba-sde-display.dtsi"
#include "camera/scuba-camera-sensor-idp.dtsi"

&soc {
	scuba_batterydata: qcom,battery-data {
		qcom,batt-id-range-pct = <15>;
		#include "qg-batterydata-alium-3600mah.dtsi"
		#include "qg-batterydata-atl466271_3300mAh.dtsi"
	};
};

&pm2250_qg {
	qcom,battery-data = <&scuba_batterydata>;
	qcom,qg-iterm-ma = <150>;
	qcom,hold-soc-while-full;
	qcom,linearize-soc;
	qcom,cl-feedback-on;
	qcom,tcss-enable;
	qcom,fvss-enable;
	qcom,fvss-vbatt-mv = <3500>;
	qcom,bass-enable;
};

&sdhc_1 {
	vdd-supply = <&L20A>;
	qcom,vdd-voltage-level = <2856000 2856000>;
	qcom,vdd-current-level = <0 570000>;

	vdd-io-supply = <&L14A>;
	qcom,vdd-io-always-on;
	qcom,vdd-io-lpm-sup;
	qcom,vdd-io-voltage-level = <1800000 1800000>;
	qcom,vdd-io-current-level = <0 325000>;

	pinctrl-names = "active", "sleep";
	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on
					&sdc1_rclk_on>;
	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off
					&sdc1_rclk_off>;

	status = "ok";
};

&scuba_snd {
	qcom,model = "bengal-scubaqrd-snd-card";
	qcom,msm-mi2s-master = <1>, <1>, <1>, <1>;
	qcom,wcn-btfm = <1>;
	qcom,ext-disp-audio-rx = <0>;
	qcom,audio-routing =
		"AMIC1", "MIC BIAS1",
		"MIC BIAS1", "Analog Mic1",
		"AMIC2", "MIC BIAS2",
		"MIC BIAS2", "Analog Mic2",
		"AMIC3", "MIC BIAS3",
		"MIC BIAS3", "Analog Mic3",
		"AMIC4", "MIC BIAS3",
		"MIC BIAS3", "Analog Mic4",
		"IN1_HPHL", "HPHL_OUT",
		"IN2_HPHR", "HPHR_OUT",
		"IN3_AUX", "AUX_OUT",
		"SpkrMono WSA_IN", "AUX",
		"TX SWR_MIC0", "ADC1_OUTPUT",
		"TX SWR_MIC1", "ADC2_OUTPUT",
		"TX SWR_MIC5", "ADC3_OUTPUT",
		"TX SWR_MIC0", "VA_TX_SWR_CLK",
		"TX SWR_MIC1", "VA_TX_SWR_CLK",
		"TX SWR_MIC2", "VA_TX_SWR_CLK",
		"TX SWR_MIC3", "VA_TX_SWR_CLK",
		"TX SWR_MIC4", "VA_TX_SWR_CLK",
		"TX SWR_MIC5", "VA_TX_SWR_CLK",
		"TX SWR_MIC6", "VA_TX_SWR_CLK",
		"TX SWR_MIC7", "VA_TX_SWR_CLK",
		"TX SWR_MIC8", "VA_TX_SWR_CLK",
		"TX SWR_MIC9", "VA_TX_SWR_CLK",
		"TX SWR_MIC10", "VA_TX_SWR_CLK",
		"TX SWR_MIC11", "VA_TX_SWR_CLK",
		"RX_TX DEC0_INP", "TX DEC0 MUX",
		"RX_TX DEC1_INP", "TX DEC1 MUX",
		"RX_TX DEC2_INP", "TX DEC2 MUX",
		"RX_TX DEC3_INP", "TX DEC3 MUX",
		"TX_AIF1 CAP", "VA_TX_SWR_CLK",
		"TX_AIF2 CAP", "VA_TX_SWR_CLK",
		"TX_AIF3 CAP", "VA_TX_SWR_CLK",
		"VA SWR_MIC0", "ADC1_OUTPUT",
		"VA SWR_MIC1", "ADC2_OUTPUT",
		"VA SWR_MIC5", "ADC3_OUTPUT";
	qcom,msm-mbhc-hphl-swh = <1>;
	qcom,msm-mbhc-gnd-swh = <1>;
	asoc-codec  = <&stub_codec>, <&bolero>;
	asoc-codec-names = "msm-stub-codec.1", "bolero_codec";
	qcom,wsa-max-devs = <1>;
	qcom,wsa-devs = <&wsa881x_i2c_e>;
	qcom,wsa-aux-dev-prefix = "SpkrMono";
	qcom,codec-max-aux-devs = <1>;
	qcom,codec-aux-devs = <&rouleur_codec>;
	qcom,msm_audio_ssr_devs = <&audio_apr>, <&q6core>, <&bolero>,
				<&lpi_tlmm>;
};

&sdhc_2 {
	vdd-supply = <&L21A>;
	qcom,vdd-voltage-level = <2960000 3300000>;
	qcom,vdd-current-level = <0 800000>;

	vdd-io-supply = <&L4A>;
	qcom,vdd-io-voltage-level = <1800000 2960000>;
	qcom,vdd-io-current-level = <0 22000>;

	pinctrl-names = "active", "sleep";
	pinctrl-0 = <&sdc2_clk_on  &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;

	cd-gpios = <&tlmm 88 GPIO_ACTIVE_HIGH>;

	status = "ok";
};

&pm2250_charger {
	qcom,auto-recharge-soc = <98>;
	qcom,suspend-input-on-debug-batt;
	qcom,battery-data = <&scuba_batterydata>;
	io-channels = <&pm2250_vadc ADC_USB_IN_V_16>,
			<&pm2250_vadc ADC_CHG_TEMP>;
	io-channel-names = "usb_in_voltage",
			"chg_temp";
	qcom,thermal-mitigation = <2000000 1500000 1000000 500000>;
};

&pm2250_pwm3 {
	status = "ok";
};

&thermal_zones {
	quiet-therm-usr {
		polling-delay = <5000>;
	};

	quiet-therm-step {
		polling-delay-passive = <2000>;
		polling-delay = <5000>;
		thermal-governor = "step_wise";
		thermal-sensors = <&pm2250_adc_tm_iio ADC_AMUX_THM2_PU2>;
		wake-capable-sensor;
		trips {
			quiet_modem_trip0: quiet-modem-trip0 {
				temperature = <40000>;
				hysteresis = <5000>;
				type = "passive";
			};

			quiet_batt_trip0: quiet-batt-trip0 {
				temperature = <41000>;
				hysteresis = <3000>;
				type = "passive";
			};

			quiet_modem_trip1: quiet-modem-trip1 {
				temperature = <42000>;
				hysteresis = <5000>;
				type = "passive";
			};

			quiet_batt_trip1: quiet-batt-trip1 {
				temperature = <43000>;
				hysteresis = <4000>;
				type = "passive";
			};

			quiet_modem_trip2: quiet-modem-trip2 {
				temperature = <43000>;
				hysteresis = <5000>;
				type = "passive";
			};

			quiet_cpu0_trip: quiet-cpu0-trip {
				temperature = <44000>;
				hysteresis = <0>;
				type = "passive";
			};

			quiet_batt_trip2: quiet-batt-trip2 {
				temperature = <45000>;
				hysteresis = <2000>;
				type = "passive";
			};

			quiet_gpu_trip: quiet-gpu-trip {
				temperature = <46000>;
				hysteresis = <0>;
				type = "passive";
			};

			quiet_batt_trip3: quiet-batt-trip3 {
				temperature = <47000>;
				hysteresis = <2000>;
				type = "passive";
			};

			quiet_modem_trip3: quiet-modem-trip3 {
				temperature = <50000>;
				hysteresis = <5000>;
				type = "passive";
			};
		};

		cooling-maps {
			gpu-cdev {
				trip = <&quiet_gpu_trip>;
				/* throttle from fmax to 921600000Hz */
				cooling-device = <&msm_gpu THERMAL_NO_LIMIT
							(THERMAL_MAX_LIMIT - 4)>;
			};

			cpu0-cdev {
				trip = <&quiet_cpu0_trip>;
				/* throttle from fmax to 1420800KHz */
				cooling-device = <&CPU0 THERMAL_NO_LIMIT
							(THERMAL_MAX_LIMIT - 5)>;
			};

			modem-proc-cdev0 {
				trip = <&quiet_modem_trip0>;
				cooling-device = <&modem_proc 1 1>;
			};

			modem-proc-cdev1 {
				trip = <&quiet_modem_trip3>;
				cooling-device = <&modem_proc 3 3>;
			};

			modem-pa-cdev0 {
				trip = <&quiet_modem_trip1>;
				cooling-device = <&modem_pa 1 1>;
			};

			modem-pa-cdev1 {
				trip = <&quiet_modem_trip2>;
				cooling-device = <&modem_pa 2 2>;
			};

			modem-pa-cdev3 {
				trip = <&quiet_modem_trip3>;
				cooling-device = <&modem_pa 3 3>;
			};

			batt-cdev0 {
				trip = <&quiet_batt_trip0>;
				cooling-device = <&pm2250_charger 1 1>;
			};

			batt-cdev1 {
				trip = <&quiet_batt_trip1>;
				cooling-device = <&pm2250_charger 2 2>;
			};

			batt-cdev2 {
				trip = <&quiet_batt_trip2>;
				cooling-device = <&pm2250_charger 3 3>;
			};

			batt-cdev3 {
				trip = <&quiet_batt_trip3>;
				cooling-device = <&pm2250_charger 4 4>;
			};
		};
	};
};

&dsi_nt36525_truly_video {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_pwm";
	pwms = <&pm2250_pwm3 0 0>;
	qcom,bl-pmic-pwm-period-usecs = <100>;
	qcom,mdss-dsi-bl-min-level = <1>;
	qcom,mdss-dsi-bl-max-level = <4095>;
	qcom,platform-reset-gpio = <&tlmm 82 0>;
	qcom,platform-reset-gpio-always-on;
	qcom,platform-en-gpio = <&tlmm 105 0>;
};

&sde_dsi {
	qcom,dsi-default-panel = <&dsi_nt36525_truly_video>;
};

&qupv3_se2_i2c {
	status = "ok";
	qcom,i2c-touch-active = "novatek,NVT-ts";

	novatek@62 {
		compatible = "novatek,NVT-ts";
		reg = <0x62>;

		interrupt-parent = <&tlmm>;
		interrupts = <80 0x2008>;
		pinctrl-names = "pmx_ts_active","pmx_ts_suspend",
			"pmx_ts_release";
		pinctrl-0 = <&ts_int_active &ts_reset_active>;
		pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
		pinctrl-2 = <&ts_release>;

		novatek,reset-gpio = <&tlmm 71 0x00>;
		novatek,irq-gpio = <&tlmm 80 0x2008>;

		panel = <&dsi_nt36525_truly_video>;
	};
};

&qusb_phy0 {
	extcon = <&pm2250_charger>;

	qcom,qusb-phy-init-seq = <0xf8 0x80
				0xb3 0x84
				0x83 0x88
				0xc5 0x8c
				0x30 0x08
				0x79 0x0c
				0x21 0x10
				0x14 0x9c
				0x80 0x04
				0x9f 0x1c
				0x00 0x18>;
};

&usb0 {
	extcon = <&qusb_phy0>, <&eud>;
};

&qupv3_se1_i2c {
	status = "ok";
	#address-cells = <1>;
	#size-cells = <0>;
	nq@28 {
		compatible = "qcom,nq-nci";
		reg = <0x28>;
		qcom,nq-irq = <&tlmm 70 0x00>;
		qcom,nq-ven = <&tlmm 69 0x00>;
		qcom,nq-firm = <&tlmm 31 0x00>;
		qcom,nq-clkreq = <&tlmm 86 0x00>;
		interrupt-parent = <&tlmm>;
		interrupts = <70 0>;
		interrupt-names = "nfc_irq";
		pinctrl-names = "nfc_active", "nfc_suspend";
		pinctrl-0 = <&nfc_int_active &nfc_enable_active
				&nfc_clk_req_active>;
		pinctrl-1 = <&nfc_int_suspend &nfc_enable_suspend
				&nfc_clk_req_suspend>;
	};
};

&tlmm {
	fpc_reset_int: fpc_reset_int {
		fpc_reset_low: reset_low {
			mux {
				pins = "gpio104";
				function = "gpio";
			};

			config {
				pins = "gpio104";
				drive-strength = <2>;
				bias-disable;
				output-low;
			};
		};

		fpc_reset_high: reset_high {
			mux {
				pins = "gpio104";
				function = "gpio";
			};

			config {
				pins = "gpio104";
				drive-strength = <2>;
				bias-disable;
				output-high;
			};
		};

		fpc_int_low: int_low {
			mux {
				pins = "gpio97";
				function = "gpio";
			};

			config {
				pins = "gpio97";
				drive-strength = <2>;
				bias-pull-down;
				input-enable;
			};
		};
	};
};

&soc {
	fingerprint: fpc1020 {
		compatible = "fpc,fpc1020";
		interrupt-parent = <&tlmm>;
		interrupts = <97 0>;
		fpc,gpio_rst = <&tlmm 104 0>;
		fpc,gpio_irq = <&tlmm 97 0>;
		fpc,enable-on-boot;
		pinctrl-names = "fpc1020_reset_reset",
				"fpc1020_reset_active",
				"fpc1020_irq_active";
		pinctrl-0 = <&fpc_reset_low>;
		pinctrl-1 = <&fpc_reset_high>;
		pinctrl-2 = <&fpc_int_low>;
	};
};