| #include <dt-bindings/clock/qcom,gcc-sdm429w.h> |
| #include <dt-bindings/clock/qcom,rpmcc.h> |
| |
| &cci { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| actuator0: qcom,actuator@0 { |
| cell-index = <0>; |
| reg = <0x0>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| cam_vaf-supply = <&pm8953_l17>; |
| qcom,cam-vreg-name = "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <2850000>; |
| qcom,cam-vreg-max-voltage = <2850000>; |
| qcom,cam-vreg-op-mode = <80000>; |
| status = "ok"; |
| }; |
| |
| actuator1: qcom,actuator@1 { |
| cell-index = <1>; |
| reg = <0x1>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <1>; |
| cam_vaf-supply = <&pm8953_l17>; |
| qcom,cam-vreg-name = "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <2850000>; |
| qcom,cam-vreg-max-voltage = <2850000>; |
| qcom,cam-vreg-op-mode = <80000>; |
| status = "ok"; |
| }; |
| |
| eeprom0: qcom,eeprom@0 { |
| cell-index = <0>; |
| compatible = "qcom,eeprom"; |
| qcom,cci-master = <0>; |
| reg = <0x0>; |
| cam_vana-supply = <&pm8953_l22>; |
| cam_vio-supply = <&pm8953_l6>; |
| cam_vaf-supply = <&pm8953_l17>; |
| cam_vdig-supply = <&pm8953_l3>; |
| qcom,cam-vreg-name = "cam_vana", |
| "cam_vio", "cam_vdig", "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <2800000 0 1200000 2850000>; |
| qcom,cam-vreg-max-voltage = <2800000 0 1200000 2850000>; |
| qcom,cam-vreg-op-mode = <80000 0 200000 100000>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_default |
| &cam_sensor_rear_reset |
| &cam_sensor_rear_vana>; |
| pinctrl-1 = <&cam_sensor_mclk0_sleep |
| &cam_sensor_rear_reset_sleep |
| &cam_sensor_rear_vana_sleep>; |
| gpios = <&tlmm 26 0>, |
| <&tlmm 36 0>, |
| <&tlmm 35 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-vana = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0", |
| "CAM_VANA"; |
| status = "ok"; |
| clocks = <&gcc MCLK0_CLK_SRC>, |
| <&gcc GCC_CAMSS_MCLK0_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <19200000 0>; |
| }; |
| |
| eeprom1: qcom,eeprom@1 { |
| cell-index = <1>; |
| reg = <0x1>; |
| qcom,eeprom-name = "sunny_8865"; |
| compatible = "qcom,eeprom"; |
| qcom,slave-addr = <0x6c>; |
| qcom,cci-master = <0>; |
| qcom,num-blocks = <8>; |
| |
| qcom,page0 = <1 0x0100 2 0x01 1 1>; |
| qcom,poll0 = <0 0x0 2 0x0 1 0>; |
| qcom,mem0 = <0 0x0 2 0x0 1 0>; |
| |
| qcom,page1 = <1 0x5002 2 0x00 1 0>; |
| qcom,poll1 = <0 0x0 2 0x0 1 0>; |
| qcom,mem1 = <0 0x0 2 0x0 1 0>; |
| |
| qcom,page2 = <1 0x3d84 2 0xc0 1 0>; |
| qcom,poll2 = <0 0x0 2 0x0 1 0>; |
| qcom,mem2 = <0 0x0 2 0x0 1 0>; |
| |
| qcom,page3 = <1 0x3d88 2 0x70 1 0>; |
| qcom,poll3 = <0 0x0 2 0x0 1 0>; |
| qcom,mem3 = <0 0x0 2 0x0 1 0>; |
| |
| qcom,page4 = <1 0x3d89 2 0x10 1 0>; |
| qcom,poll4 = <0 0x0 2 0x0 1 0>; |
| qcom,mem4 = <0 0x0 2 0x0 1 0>; |
| |
| qcom,page5 = <1 0x3d8a 2 0x70 1 0>; |
| qcom,poll5 = <0 0x0 2 0x0 1 0>; |
| qcom,mem5 = <0 0x0 2 0x0 1 0>; |
| |
| qcom,page6 = <1 0x3d8b 2 0xf4 1 0>; |
| qcom,poll6 = <0 0x0 2 0x0 1 0>; |
| qcom,mem6 = <0 0x0 2 0x0 1 0>; |
| |
| qcom,page7 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll7 = <0 0x0 2 0x0 1 1>; |
| qcom,mem7 = <1536 0x7010 2 0 1 0>; |
| |
| cam_vdig-supply = <&pm8953_l23>; |
| cam_vana-supply = <&pm8953_l22>; |
| cam_vio-supply = <&pm8953_l6>; |
| cam_vaf-supply = <&pm8953_l17>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <1200000 0 2800000 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2800000 2850000>; |
| qcom,cam-vreg-op-mode = <105000 0 80000 100000>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_default |
| &cam_sensor_front1_default>; |
| pinctrl-1 = <&cam_sensor_mclk2_sleep &cam_sensor_front1_sleep>; |
| gpios = <&tlmm 28 0>, |
| <&tlmm 40 0>, |
| <&tlmm 39 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2", |
| "CAM_STANDBY2"; |
| qcom,cam-power-seq-type = "sensor_vreg", "sensor_vreg", |
| "sensor_vreg", |
| "sensor_gpio", "sensor_gpio" , "sensor_clk"; |
| qcom,cam-power-seq-val = "cam_vdig", "cam_vana", "cam_vio", |
| "sensor_gpio_reset", "sensor_gpio_standby", |
| "sensor_cam_mclk"; |
| qcom,cam-power-seq-cfg-val = <1 1 1 1 1 24000000>; |
| qcom,cam-power-seq-delay = <1 1 1 30 30 5>; |
| status = "ok"; |
| clocks = <&gcc MCLK2_CLK_SRC>, |
| <&gcc GCC_CAMSS_MCLK2_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <19200000 0>; |
| }; |
| |
| eeprom2: qcom,eeprom@2 { |
| cell-index = <2>; |
| compatible = "qcom,eeprom"; |
| qcom,cci-master = <1>; |
| reg = <0x2>; |
| cam_vdig-supply = <&pm8953_l3>; |
| cam_vana-supply = <&pm8953_l22>; |
| cam_vio-supply = <&pm8953_l6>; |
| cam_vaf-supply = <&pm8953_l17>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <1200000 0 2800000 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2800000 2850000>; |
| qcom,cam-vreg-op-mode = <105000 0 80000 100000>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_default |
| &cam_sensor_front1_default>; |
| pinctrl-1 = <&cam_sensor_mclk2_sleep |
| &cam_sensor_front1_sleep>; |
| gpios = <&tlmm 28 0>, |
| <&tlmm 40 0>, |
| <&tlmm 39 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2", |
| "CAM_STANDBY2"; |
| status = "ok"; |
| clocks = <&gcc MCLK2_CLK_SRC>, |
| <&gcc GCC_CAMSS_MCLK2_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <19200000 0>; |
| }; |
| |
| qcom,camera@0 { |
| cell-index = <0>; |
| compatible = "qcom,camera"; |
| reg = <0x0>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <270>; |
| qcom,led-flash-src = <&led_flash0>; |
| qcom,eeprom-src = <&eeprom0>; |
| qcom,actuator-src = <&actuator0>; |
| cam_vana-supply = <&pm8953_l22>; |
| cam_vio-supply = <&pm8953_l6>; |
| cam_vaf-supply = <&pm8953_l17>; |
| cam_vdig-supply = <&pm8953_l3>; |
| qcom,cam-vreg-name = "cam_vana", |
| "cam_vio", "cam_vdig", "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <2800000 0 1200000 2850000>; |
| qcom,cam-vreg-max-voltage = <2800000 0 1200000 2850000>; |
| qcom,cam-vreg-op-mode = <80000 0 200000 100000>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_default |
| &cam_sensor_rear_reset |
| &cam_sensor_rear_vana>; |
| pinctrl-1 = <&cam_sensor_mclk0_sleep |
| &cam_sensor_rear_reset_sleep |
| &cam_sensor_rear_vana_sleep>; |
| gpios = <&tlmm 26 0>, |
| <&tlmm 36 0>, |
| <&tlmm 35 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-vana = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0", |
| "CAM_VANA"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| clocks = <&gcc MCLK0_CLK_SRC>, |
| <&gcc GCC_CAMSS_MCLK0_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| qcom,camera@1 { |
| cell-index = <1>; |
| compatible = "qcom,camera"; |
| reg = <0x1>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,mount-angle = <90>; |
| cam_vdig-supply = <&pm8953_l3>; |
| cam_vana-supply = <&pm8953_l22>; |
| cam_vio-supply = <&pm8953_l6>; |
| cam_vaf-supply = <&pm8953_l17>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <1200000 0 2800000 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2800000 2850000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000 100000>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk1_default |
| &cam_sensor_front_default>; |
| pinctrl-1 = <&cam_sensor_mclk1_sleep |
| &cam_sensor_front_sleep>; |
| gpios = <&tlmm 27 0>, |
| <&tlmm 38 0>, |
| <&tlmm 50 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK1", |
| "CAM_RESET1", |
| "CAM_STANDBY1"; |
| qcom,sensor-position = <0x100>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <1>; |
| clocks = <&gcc MCLK1_CLK_SRC>, |
| <&gcc GCC_CAMSS_MCLK1_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| qcom,camera@2 { |
| cell-index = <2>; |
| compatible = "qcom,camera"; |
| reg = <0x02>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,mount-angle = <90>; |
| qcom,eeprom-src = <&eeprom2>; |
| qcom,actuator-src = <&actuator1>; |
| cam_vdig-supply = <&pm8953_l3>; |
| cam_vana-supply = <&pm8953_l22>; |
| cam_vio-supply = <&pm8953_l6>; |
| cam_vaf-supply = <&pm8953_l17>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <1200000 0 2800000 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2800000 2850000>; |
| qcom,cam-vreg-op-mode = <105000 0 80000 100000>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_default |
| &cam_sensor_front1_default>; |
| pinctrl-1 = <&cam_sensor_mclk2_sleep |
| &cam_sensor_front1_sleep>; |
| gpios = <&tlmm 28 0>, |
| <&tlmm 40 0>, |
| <&tlmm 39 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2", |
| "CAM_STANDBY2"; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| clocks = <&gcc MCLK2_CLK_SRC>, |
| <&gcc GCC_CAMSS_MCLK2_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| }; |