pinctrl: abx500: rework error path
At several places, return value was not tested
and error output was missing.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
diff --git a/drivers/pinctrl/pinctrl-abx500.c b/drivers/pinctrl/pinctrl-abx500.c
index f0e3f28..1d3f988 100644
--- a/drivers/pinctrl/pinctrl-abx500.c
+++ b/drivers/pinctrl/pinctrl-abx500.c
@@ -134,8 +134,8 @@
if (ret < 0)
dev_err(pct->dev,
- "%s read reg =%x, offset=%x failed\n",
- __func__, reg, offset);
+ "%s read reg =%x, offset=%x failed (%d)\n",
+ __func__, reg, offset, ret);
return ret;
}
@@ -151,7 +151,8 @@
ret = abx500_mask_and_set_register_interruptible(pct->dev,
AB8500_MISC, reg, BIT(pos), val << pos);
if (ret < 0)
- dev_err(pct->dev, "%s write failed\n", __func__);
+ dev_err(pct->dev, "%s write reg, %x offset %x failed (%d)\n",
+ __func__, reg, offset, ret);
return ret;
}
@@ -171,10 +172,8 @@
ret = abx500_gpio_get_bit(chip, AB8500_GPIO_DIR1_REG,
gpio_offset, &is_out);
- if (ret < 0) {
- dev_err(pct->dev, "%s failed\n", __func__);
- return ret;
- }
+ if (ret < 0)
+ goto out;
if (is_out)
ret = abx500_gpio_get_bit(chip, AB8500_GPIO_OUT1_REG,
@@ -182,8 +181,9 @@
else
ret = abx500_gpio_get_bit(chip, AB8500_GPIO_IN1_REG,
gpio_offset, &bit);
+out:
if (ret < 0) {
- dev_err(pct->dev, "%s failed\n", __func__);
+ dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
return ret;
}
@@ -197,7 +197,7 @@
ret = abx500_gpio_set_bits(chip, AB8500_GPIO_OUT1_REG, offset, val);
if (ret < 0)
- dev_err(pct->dev, "%s write failed\n", __func__);
+ dev_err(pct->dev, "%s write failed (%d)\n", __func__, ret);
}
static int abx500_get_pull_updown(struct abx500_pinctrl *pct, int offset,
@@ -294,7 +294,7 @@
offset,
ABX500_GPIO_OUTPUT);
if (ret < 0)
- return ret;
+ goto out;
/* disable pull down */
ret = abx500_gpio_set_bits(chip,
@@ -302,7 +302,7 @@
offset,
ABX500_GPIO_PULL_NONE);
if (ret < 0)
- return ret;
+ goto out;
/* if supported, disable both pull down and pull up */
gpio = offset + 1;
@@ -310,8 +310,11 @@
ret = abx500_set_pull_updown(pct,
gpio,
ABX500_GPIO_PULL_NONE);
- if (ret < 0)
- return ret;
+ }
+out:
+ if (ret < 0) {
+ dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
+ return ret;
}
/* set the output as 1 or 0 */
@@ -409,10 +412,16 @@
if (af.alt_bit1 != UNUSED) {
ret = abx500_gpio_set_bits(chip, AB8500_GPIO_SEL1_REG,
offset, 0);
+ if (ret < 0)
+ goto out;
+
ret = abx500_gpio_set_bits(chip,
AB8500_GPIO_ALTFUN_REG,
af.alt_bit1,
!!(af.alta_val && BIT(0)));
+ if (ret < 0)
+ goto out;
+
if (af.alt_bit2 != UNUSED)
ret = abx500_gpio_set_bits(chip,
AB8500_GPIO_ALTFUN_REG,
@@ -426,8 +435,14 @@
case ABX500_ALT_B:
ret = abx500_gpio_set_bits(chip, AB8500_GPIO_SEL1_REG,
offset, 0);
+ if (ret < 0)
+ goto out;
+
ret = abx500_gpio_set_bits(chip, AB8500_GPIO_ALTFUN_REG,
af.alt_bit1, !!(af.altb_val && BIT(0)));
+ if (ret < 0)
+ goto out;
+
if (af.alt_bit2 != UNUSED)
ret = abx500_gpio_set_bits(chip,
AB8500_GPIO_ALTFUN_REG,
@@ -438,8 +453,14 @@
case ABX500_ALT_C:
ret = abx500_gpio_set_bits(chip, AB8500_GPIO_SEL1_REG,
offset, 0);
+ if (ret < 0)
+ goto out;
+
ret = abx500_gpio_set_bits(chip, AB8500_GPIO_ALTFUN_REG,
af.alt_bit2, !!(af.altc_val && BIT(0)));
+ if (ret < 0)
+ goto out;
+
ret = abx500_gpio_set_bits(chip, AB8500_GPIO_ALTFUN_REG,
af.alt_bit2, !!(af.altc_val && BIT(1)));
break;
@@ -449,11 +470,14 @@
return -EINVAL;
}
+out:
+ if (ret < 0)
+ dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
return ret;
}
-static u8 abx500_get_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
+static int abx500_get_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
unsigned gpio)
{
u8 mode;
@@ -464,6 +488,7 @@
struct alternate_functions af = pct->soc->alternate_functions[gpio];
/* on ABx5xx, there is no GPIO0, so adjust the offset */
unsigned offset = gpio - 1;
+ int ret;
/*
* if gpiosel_bit is set to unused,
@@ -473,8 +498,11 @@
return ABX500_DEFAULT;
/* read GpioSelx register */
- abx500_gpio_get_bit(chip, AB8500_GPIO_SEL1_REG + (offset / 8),
+ ret = abx500_gpio_get_bit(chip, AB8500_GPIO_SEL1_REG + (offset / 8),
af.gpiosel_bit, &bit_mode);
+ if (ret < 0)
+ goto out;
+
mode = bit_mode;
/* sanity check */
@@ -506,14 +534,19 @@
* pin use the AlternatFunction register
* read alt_bit1 value
*/
- abx500_gpio_get_bit(chip, AB8500_GPIO_ALTFUN_REG,
+ ret = abx500_gpio_get_bit(chip, AB8500_GPIO_ALTFUN_REG,
af.alt_bit1, &alt_bit1);
+ if (ret < 0)
+ goto out;
- if (af.alt_bit2 != UNUSED)
+ if (af.alt_bit2 != UNUSED) {
/* read alt_bit2 value */
- abx500_gpio_get_bit(chip, AB8500_GPIO_ALTFUN_REG, af.alt_bit2,
+ ret = abx500_gpio_get_bit(chip, AB8500_GPIO_ALTFUN_REG,
+ af.alt_bit2,
&alt_bit2);
- else
+ if (ret < 0)
+ goto out;
+ } else
alt_bit2 = 0;
mode = (alt_bit2 << 1) + alt_bit1;
@@ -523,6 +556,10 @@
return ABX500_ALT_B;
else
return ABX500_ALT_C;
+
+out:
+ dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
+ return ret;
}
#ifdef CONFIG_DEBUG_FS
@@ -541,6 +578,7 @@
bool is_out;
bool pd;
enum abx500_gpio_pull_updown pud = 0;
+ int ret;
const char *modes[] = {
[ABX500_DEFAULT] = "default",
@@ -556,7 +594,10 @@
[ABX500_GPIO_PULL_UP] = "pull up",
};
- abx500_gpio_get_bit(chip, AB8500_GPIO_DIR1_REG, gpio_offset, &is_out);
+ ret = abx500_gpio_get_bit(chip, AB8500_GPIO_DIR1_REG,
+ gpio_offset, &is_out);
+ if (ret < 0)
+ goto out;
seq_printf(s, " gpio-%-3d (%-20.20s) %-3s",
gpio, label ?: "(none)",
@@ -564,11 +605,17 @@
if (!is_out) {
if (abx500_pullud_supported(chip, offset)) {
- abx500_get_pull_updown(pct, offset, &pud);
+ ret = abx500_get_pull_updown(pct, offset, &pud);
+ if (ret < 0)
+ goto out;
+
seq_printf(s, " %-9s", pull_up_down[pud]);
} else {
- abx500_gpio_get_bit(chip, AB8500_GPIO_PUD1_REG,
- gpio_offset, &pd);
+ ret = abx500_gpio_get_bit(chip, AB8500_GPIO_PUD1_REG,
+ gpio_offset, &pd);
+ if (ret < 0)
+ goto out;
+
seq_printf(s, " %-9s", pull_up_down[pd]);
}
} else
@@ -578,6 +625,10 @@
mode = abx500_get_mode(pctldev, chip, offset);
seq_printf(s, " %s", (mode < 0) ? "unknown" : modes[mode]);
+
+out:
+ if (ret < 0)
+ dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
}
static void abx500_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
@@ -681,6 +732,9 @@
ret = abx500_set_mode(pctldev, chip, g->pins[i], g->altsetting);
}
+ if (ret < 0)
+ dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
+
return ret;
}
@@ -729,10 +783,8 @@
ret = abx500_set_mode(pct->pctldev, &pct->chip,
offset, p->altfunc);
- if (ret < 0) {
+ if (ret < 0)
dev_err(pct->dev, "%s setting altfunc failed\n", __func__);
- return ret;
- }
return ret;
}
@@ -1009,6 +1061,8 @@
switch (param) {
case PIN_CONFIG_BIAS_DISABLE:
ret = abx500_gpio_direction_input(chip, offset);
+ if (ret < 0)
+ goto out;
/*
* Some chips only support pull down, while some actually
* support both pull up and pull down. Such chips have
@@ -1028,6 +1082,8 @@
case PIN_CONFIG_BIAS_PULL_DOWN:
ret = abx500_gpio_direction_input(chip, offset);
+ if (ret < 0)
+ goto out;
/*
* if argument = 1 set the pull down
* else clear the pull down
@@ -1050,6 +1106,8 @@
case PIN_CONFIG_BIAS_PULL_UP:
ret = abx500_gpio_direction_input(chip, offset);
+ if (ret < 0)
+ goto out;
/*
* if argument = 1 set the pull up
* else clear the pull up
@@ -1070,12 +1128,14 @@
case PIN_CONFIG_OUTPUT:
ret = abx500_gpio_direction_output(chip, offset, argument);
-
break;
default:
dev_err(chip->dev, "illegal configuration requested\n");
}
+out:
+ if (ret < 0)
+ dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
return ret;
}