r8152: move the settings of PHY to a work queue
Move the settings of PHY to a work queue and schedule it after
rtl_ops.init().
There are some reasons for this. First, the settings are only
needed for the first time initialization or after the power
down occurs.
Second, the settings are independent with the others.
Last, the settings may take more time than the others. Leave
they in probe() or open() may delay the following flows.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c
index 161c25e..46fe9a7 100644
--- a/drivers/net/usb/r8152.c
+++ b/drivers/net/usb/r8152.c
@@ -602,7 +602,7 @@
struct list_head rx_done, tx_free;
struct sk_buff_head tx_queue, rx_queue;
spinlock_t rx_lock, tx_lock;
- struct delayed_work schedule;
+ struct delayed_work schedule, hw_phy_work;
struct mii_if_info mii;
struct mutex control; /* use for hw setting */
#ifdef CONFIG_PM_SLEEP
@@ -619,6 +619,7 @@
int (*eee_get)(struct r8152 *, struct ethtool_eee *);
int (*eee_set)(struct r8152 *, struct ethtool_eee *);
bool (*in_nway)(struct r8152 *);
+ void (*hw_phy_cfg)(struct r8152 *);
} rtl_ops;
int intr_interval;
@@ -2499,8 +2500,6 @@
rxdy_gated_en(tp, true);
r8153_teredo_off(tp);
- r8152b_hw_phy_cfg(tp);
-
ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CRWECR, CRWECR_NORAML);
ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CR, 0x00);
@@ -2678,8 +2677,6 @@
ocp_data &= ~RCR_ACPT_ALL;
ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data);
- r8153_hw_phy_cfg(tp);
-
rtl8152_nic_reset(tp);
ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL);
@@ -3040,6 +3037,25 @@
usb_autopm_put_interface(tp->intf);
}
+static void rtl_hw_phy_work_func_t(struct work_struct *work)
+{
+ struct r8152 *tp = container_of(work, struct r8152, hw_phy_work.work);
+
+ if (test_bit(RTL8152_UNPLUG, &tp->flags))
+ return;
+
+ if (usb_autopm_get_interface(tp->intf) < 0)
+ return;
+
+ mutex_lock(&tp->control);
+
+ tp->rtl_ops.hw_phy_cfg(tp);
+
+ mutex_unlock(&tp->control);
+
+ usb_autopm_put_interface(tp->intf);
+}
+
#ifdef CONFIG_PM_SLEEP
static int rtl_notifier(struct notifier_block *nb, unsigned long action,
void *data)
@@ -3518,6 +3534,7 @@
if (!test_bit(SELECTIVE_SUSPEND, &tp->flags)) {
tp->rtl_ops.init(tp);
+ queue_delayed_work(system_long_wq, &tp->hw_phy_work, 0);
netif_device_attach(tp->netdev);
}
@@ -4122,6 +4139,7 @@
ops->eee_get = r8152_get_eee;
ops->eee_set = r8152_set_eee;
ops->in_nway = rtl8152_in_nway;
+ ops->hw_phy_cfg = r8152b_hw_phy_cfg;
break;
case RTL_VER_03:
@@ -4137,6 +4155,7 @@
ops->eee_get = r8153_get_eee;
ops->eee_set = r8153_set_eee;
ops->in_nway = rtl8153_in_nway;
+ ops->hw_phy_cfg = r8153_hw_phy_cfg;
break;
default:
@@ -4183,6 +4202,7 @@
mutex_init(&tp->control);
INIT_DELAYED_WORK(&tp->schedule, rtl_work_func_t);
+ INIT_DELAYED_WORK(&tp->hw_phy_work, rtl_hw_phy_work_func_t);
netdev->netdev_ops = &rtl8152_netdev_ops;
netdev->watchdog_timeo = RTL8152_TX_TIMEOUT;
@@ -4225,6 +4245,7 @@
intf->needs_remote_wakeup = 1;
tp->rtl_ops.init(tp);
+ queue_delayed_work(system_long_wq, &tp->hw_phy_work, 0);
set_ethernet_addr(tp);
usb_set_intfdata(intf, tp);
@@ -4270,6 +4291,7 @@
netif_napi_del(&tp->napi);
unregister_netdev(tp->netdev);
+ cancel_delayed_work_sync(&tp->hw_phy_work);
tp->rtl_ops.unload(tp);
free_netdev(tp->netdev);
}