davinci: add keypad config for tnetv107x evm board
This patch adds evm board specific keymap definitions and controller
configuration data for on-chip keypad controller on tnetv107x silicon.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
diff --git a/arch/arm/mach-davinci/board-tnetv107x-evm.c b/arch/arm/mach-davinci/board-tnetv107x-evm.c
index fe2a9d9..5afa8fc 100644
--- a/arch/arm/mach-davinci/board-tnetv107x-evm.c
+++ b/arch/arm/mach-davinci/board-tnetv107x-evm.c
@@ -23,6 +23,9 @@
#include <linux/ratelimit.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#include <linux/input.h>
+#include <linux/input/matrix_keypad.h>
+
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
@@ -141,10 +144,63 @@
.enabled_uarts = BIT(1),
};
+static const uint32_t keymap[] = {
+ KEY(0, 0, KEY_NUMERIC_1),
+ KEY(0, 1, KEY_NUMERIC_2),
+ KEY(0, 2, KEY_NUMERIC_3),
+ KEY(0, 3, KEY_FN_F1),
+ KEY(0, 4, KEY_MENU),
+
+ KEY(1, 0, KEY_NUMERIC_4),
+ KEY(1, 1, KEY_NUMERIC_5),
+ KEY(1, 2, KEY_NUMERIC_6),
+ KEY(1, 3, KEY_UP),
+ KEY(1, 4, KEY_FN_F2),
+
+ KEY(2, 0, KEY_NUMERIC_7),
+ KEY(2, 1, KEY_NUMERIC_8),
+ KEY(2, 2, KEY_NUMERIC_9),
+ KEY(2, 3, KEY_LEFT),
+ KEY(2, 4, KEY_ENTER),
+
+ KEY(3, 0, KEY_NUMERIC_STAR),
+ KEY(3, 1, KEY_NUMERIC_0),
+ KEY(3, 2, KEY_NUMERIC_POUND),
+ KEY(3, 3, KEY_DOWN),
+ KEY(3, 4, KEY_RIGHT),
+
+ KEY(4, 0, KEY_FN_F3),
+ KEY(4, 1, KEY_FN_F4),
+ KEY(4, 2, KEY_MUTE),
+ KEY(4, 3, KEY_HOME),
+ KEY(4, 4, KEY_BACK),
+
+ KEY(5, 0, KEY_VOLUMEDOWN),
+ KEY(5, 1, KEY_VOLUMEUP),
+ KEY(5, 2, KEY_F1),
+ KEY(5, 3, KEY_F2),
+ KEY(5, 4, KEY_F3),
+};
+
+static const struct matrix_keymap_data keymap_data = {
+ .keymap = keymap,
+ .keymap_size = ARRAY_SIZE(keymap),
+};
+
+static struct matrix_keypad_platform_data keypad_config = {
+ .keymap_data = &keymap_data,
+ .num_row_gpios = 6,
+ .num_col_gpios = 5,
+ .debounce_ms = 0, /* minimum */
+ .active_low = 0, /* pull up realization */
+ .no_autorepeat = 0,
+};
+
static struct tnetv107x_device_info evm_device_info __initconst = {
.serial_config = &serial_config,
.mmc_config[1] = &mmc_config, /* controller 1 */
.nand_config[0] = &nand_config, /* chip select 0 */
+ .keypad_config = &keypad_config,
};
static __init void tnetv107x_evm_board_init(void)