omap3: igep3: Fix IGEP module second MMC channel power supply
The second MMC channel (used by the WLAN/BT module) is not linked to
power regulator. This causes the WLAN/BT module to fail being detected if
CONFIG_REGULATOR_DUMMY is not set.
This patch adds the two regulators that actually feed the WLAN/BT module
(1v8 from the TWL4030 VIO LDO, and a fixed 3v3). With that patch, the
second channel is properly detected.
Also change vmmc1 to use symbolic names instead of direct device
reference.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap2/board-igep0030.c b/arch/arm/mach-omap2/board-igep0030.c
index f0a85c1..11b944f 100644
--- a/arch/arm/mach-omap2/board-igep0030.c
+++ b/arch/arm/mach-omap2/board-igep0030.c
@@ -19,6 +19,7 @@
#include <linux/interrupt.h>
#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
#include <linux/i2c/twl.h>
#include <linux/mmc/host.h>
@@ -140,9 +141,8 @@
static void __init igep3_flash_init(void) {}
#endif
-static struct regulator_consumer_supply igep3_vmmc1_supply = {
- .supply = "vmmc",
-};
+static struct regulator_consumer_supply igep3_vmmc1_supply =
+ REGULATOR_SUPPLY("vmmc", "mmci-omap-hs.0");
/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
static struct regulator_init_data igep3_vmmc1 = {
@@ -159,6 +159,52 @@
.consumer_supplies = &igep3_vmmc1_supply,
};
+static struct regulator_consumer_supply igep3_vio_supply =
+ REGULATOR_SUPPLY("vmmc_aux", "mmci-omap-hs.1");
+
+static struct regulator_init_data igep3_vio = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = 1,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &igep3_vio_supply,
+};
+
+static struct regulator_consumer_supply igep3_vmmc2_supply =
+ REGULATOR_SUPPLY("vmmc", "mmci-omap-hs.1");
+
+static struct regulator_init_data igep3_vmmc2 = {
+ .constraints = {
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ .always_on = 1,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &igep3_vmmc2_supply,
+};
+
+static struct fixed_voltage_config igep3_vwlan = {
+ .supply_name = "vwlan",
+ .microvolts = 3300000,
+ .gpio = -EINVAL,
+ .enabled_at_boot = 1,
+ .init_data = &igep3_vmmc2,
+};
+
+static struct platform_device igep3_vwlan_device = {
+ .name = "reg-fixed-voltage",
+ .id = 0,
+ .dev = {
+ .platform_data = &igep3_vwlan,
+ },
+};
+
static struct omap2_hsmmc_info mmc[] = {
[0] = {
.mmc = 1,
@@ -254,12 +300,6 @@
mmc[0].gpio_cd = gpio + 0;
omap2_hsmmc_init(mmc);
- /*
- * link regulators to MMC adapters ... we "know" the
- * regulators will be set up only *after* we return.
- */
- igep3_vmmc1_supply.dev = mmc[0].dev;
-
/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
if ((gpio_request(gpio+TWL4030_GPIO_MAX+1, "gpio-led:green:d1") == 0)
@@ -287,6 +327,10 @@
.usb_mode = T2_USB_MODE_ULPI,
};
+static struct platform_device *igep3_devices[] __initdata = {
+ &igep3_vwlan_device,
+};
+
static void __init igep3_init_irq(void)
{
omap2_init_common_infrastructure();
@@ -303,6 +347,7 @@
.usb = &igep3_twl4030_usb_data,
.gpio = &igep3_twl4030_gpio_pdata,
.vmmc1 = &igep3_vmmc1,
+ .vio = &igep3_vio,
};
static struct i2c_board_info __initdata igep3_i2c_boardinfo[] = {
@@ -387,7 +432,7 @@
/* Register I2C busses and drivers */
igep3_i2c_init();
-
+ platform_add_devices(igep3_devices, ARRAY_SIZE(igep3_devices));
omap_serial_init();
usb_musb_init(&musb_board_data);
usb_ehci_init(&ehci_pdata);