[ARM] 4905/1: [AT91] Atmel SAM9 boards updated to new-style UART initialization
Convert the Atmel SAM9260-EK, SAM9261-EK, SAM9263-EK and SAM9RL-EK
boards to use the new-style UART initialization.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
index 8c657a9..4405536 100644
--- a/arch/arm/mach-at91/board-sam9260ek.c
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -42,24 +42,24 @@
#include "generic.h"
-/*
- * Serial port configuration.
- * 0 .. 5 = USART0 .. USART5
- * 6 = DBGU
- */
-static struct at91_uart_config __initdata ek_uart_config = {
- .console_tty = 0, /* ttyS0 */
- .nr_tty = 3,
- .tty_map = { 6, 0, 1, -1, -1, -1, -1 } /* ttyS0, ..., ttyS6 */
-};
-
static void __init ek_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91sam9260_initialize(18432000);
- /* Setup the serial ports and console */
- at91_init_serial(&ek_uart_config);
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
}
static void __init ek_init_irq(void)
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index f71ff75..3c73825 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -49,17 +49,6 @@
#include "generic.h"
-/*
- * Serial port configuration.
- * 0 .. 2 = USART0 .. USART2
- * 3 = DBGU
- */
-static struct at91_uart_config __initdata ek_uart_config = {
- .console_tty = 0, /* ttyS0 */
- .nr_tty = 1,
- .tty_map = { 3, -1, -1, -1 } /* ttyS0, ..., ttyS3 */
-};
-
static void __init ek_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
@@ -68,8 +57,11 @@
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14);
- /* Setup the serial ports and console */
- at91_init_serial(&ek_uart_config);
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
}
static void __init ek_init_irq(void)
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index a65bd16..86a7fb1 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -48,24 +48,19 @@
#include "generic.h"
-/*
- * Serial port configuration.
- * 0 .. 2 = USART0 .. USART2
- * 3 = DBGU
- */
-static struct at91_uart_config __initdata ek_uart_config = {
- .console_tty = 0, /* ttyS0 */
- .nr_tty = 2,
- .tty_map = { 3, 0, -1, -1, } /* ttyS0, ..., ttyS3 */
-};
-
static void __init ek_map_io(void)
{
/* Initialize processor: 16.367 MHz crystal */
at91sam9263_initialize(16367660);
- /* Setup the serial ports and console */
- at91_init_serial(&ek_uart_config);
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
}
static void __init ek_init_irq(void)
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index ce83b60..ffc0597 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -34,24 +34,19 @@
#include "generic.h"
-/*
- * Serial port configuration.
- * 0 .. 3 = USART0 .. USART3
- * 4 = DBGU
- */
-static struct at91_uart_config __initdata ek_uart_config = {
- .console_tty = 0, /* ttyS0 */
- .nr_tty = 2,
- .tty_map = { 4, 0, -1, -1, -1 } /* ttyS0, ..., ttyS4 */
-};
-
static void __init ek_map_io(void)
{
/* Initialize processor: 12.000 MHz crystal */
at91sam9rl_initialize(12000000);
- /* Setup the serial ports and console */
- at91_init_serial(&ek_uart_config);
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
}
static void __init ek_init_irq(void)