qeth: set promisc off after trace disabling failure
If HiperSockets Network Traffic Analyzer is switched off, but trace
disabling fails somehow, the qeth driver does not switch off its
promisc mode status. A following sniffer reactivation fails, since
qeth does not see a need to reenable tracing.
At the same time the code analyzing results of trace commands is
restructured.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/s390/net/qeth_l3_main.c b/drivers/s390/net/qeth_l3_main.c
index 42fe92c..cd746da 100644
--- a/drivers/s390/net/qeth_l3_main.c
+++ b/drivers/s390/net/qeth_l3_main.c
@@ -1691,39 +1691,43 @@
cmd = (struct qeth_ipa_cmd *)data;
rc = cmd->hdr.return_code;
- if (rc) {
+ if (rc)
QETH_DBF_TEXT_(TRACE, 2, "dxter%x", rc);
- if (cmd->data.diagass.action == QETH_DIAGS_CMD_TRACE_ENABLE) {
- switch (rc) {
- case IPA_RC_HARDWARE_AUTH_ERROR:
- dev_warn(&card->gdev->dev, "The device is not "
- "authorized to run as a HiperSockets "
- "network traffic analyzer\n");
- break;
- case IPA_RC_TRACE_ALREADY_ACTIVE:
- dev_warn(&card->gdev->dev, "A HiperSockets "
- "network traffic analyzer is already "
- "active in the HiperSockets LAN\n");
- break;
- default:
- break;
- }
- }
- return 0;
- }
-
switch (cmd->data.diagass.action) {
case QETH_DIAGS_CMD_TRACE_QUERY:
break;
case QETH_DIAGS_CMD_TRACE_DISABLE:
- card->info.promisc_mode = SET_PROMISC_MODE_OFF;
- dev_info(&card->gdev->dev, "The HiperSockets network traffic "
- "analyzer is deactivated\n");
+ switch (rc) {
+ case 0:
+ case IPA_RC_INVALID_SUBCMD:
+ card->info.promisc_mode = SET_PROMISC_MODE_OFF;
+ dev_info(&card->gdev->dev, "The HiperSockets network "
+ "traffic analyzer is deactivated\n");
+ break;
+ default:
+ break;
+ }
break;
case QETH_DIAGS_CMD_TRACE_ENABLE:
- card->info.promisc_mode = SET_PROMISC_MODE_ON;
- dev_info(&card->gdev->dev, "The HiperSockets network traffic "
- "analyzer is activated\n");
+ switch (rc) {
+ case 0:
+ card->info.promisc_mode = SET_PROMISC_MODE_ON;
+ dev_info(&card->gdev->dev, "The HiperSockets network "
+ "traffic analyzer is activated\n");
+ break;
+ case IPA_RC_HARDWARE_AUTH_ERROR:
+ dev_warn(&card->gdev->dev, "The device is not "
+ "authorized to run as a HiperSockets network "
+ "traffic analyzer\n");
+ break;
+ case IPA_RC_TRACE_ALREADY_ACTIVE:
+ dev_warn(&card->gdev->dev, "A HiperSockets "
+ "network traffic analyzer is already "
+ "active in the HiperSockets LAN\n");
+ break;
+ default:
+ break;
+ }
break;
default:
QETH_DBF_MESSAGE(2, "Unknown sniffer action (0x%04x) on %s\n",