| /* |
| * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ |
| * Copyright (C) 2014 Stefan Roese <sr@denx.de> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| /dts-v1/; |
| |
| #include "omap34xx.dtsi" |
| |
| /* Secure omaps have some devices inaccessible depending on the firmware */ |
| &aes { |
| status = "disabled"; |
| }; |
| |
| &sham { |
| status = "disabled"; |
| }; |
| |
| / { |
| cpus { |
| cpu@0 { |
| cpu0-supply = <&vcc>; |
| }; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x80000000 0x10000000>; /* 256 MB */ |
| }; |
| |
| /* HS USB Port 2 Power */ |
| hsusb2_power: hsusb2_power_reg { |
| compatible = "regulator-fixed"; |
| regulator-name = "hsusb2_vbus"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&twl_gpio 18 GPIO_ACTIVE_HIGH>; /* GPIO LEDA */ |
| startup-delay-us = <70000>; |
| }; |
| |
| /* HS USB Host PHY on PORT 2 */ |
| hsusb2_phy: hsusb2_phy { |
| compatible = "usb-nop-xceiv"; |
| reset-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>; /* gpio_162 */ |
| vcc-supply = <&hsusb2_power>; |
| }; |
| |
| sound { |
| compatible = "ti,omap-twl4030"; |
| ti,model = "omap3beagle"; |
| |
| /* McBSP2 is used for onboard sound, same as on beagle */ |
| ti,mcbsp = <&mcbsp2>; |
| }; |
| |
| /* Regulator to enable/switch the vcc of the Wifi module */ |
| mmc2_sdio_poweron: regulator-mmc2-sdio-poweron { |
| compatible = "regulator-fixed"; |
| regulator-name = "regulator-mmc2-sdio-poweron"; |
| regulator-min-microvolt = <3150000>; |
| regulator-max-microvolt = <3150000>; |
| gpio = <&gpio5 29 GPIO_ACTIVE_LOW>; /* gpio_157 */ |
| enable-active-low; |
| startup-delay-us = <10000>; |
| }; |
| }; |
| |
| &omap3_pmx_core { |
| hsusbb2_pins: pinmux_hsusbb2_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ |
| OMAP3_CORE1_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ |
| OMAP3_CORE1_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ |
| OMAP3_CORE1_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ |
| OMAP3_CORE1_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ |
| OMAP3_CORE1_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ |
| OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ |
| OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ |
| OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ |
| OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ |
| OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ |
| OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ |
| >; |
| }; |
| |
| mmc1_pins: pinmux_mmc1_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ |
| OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ |
| OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ |
| OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ |
| OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ |
| OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ |
| OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */ |
| OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */ |
| OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */ |
| OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */ |
| >; |
| }; |
| |
| mmc2_pins: pinmux_mmc2_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ |
| OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ |
| OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ |
| OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ |
| OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ |
| OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ |
| >; |
| }; |
| |
| /* wlan GPIO output for WLAN_EN */ |
| wlan_gpio: pinmux_wlan_gpio { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr gpio_157 */ |
| >; |
| }; |
| |
| uart3_pins: pinmux_uart3_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ |
| OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ |
| >; |
| }; |
| |
| i2c3_pins: pinmux_i2c3_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl.i2c3_scl */ |
| OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda.i2c3_sda */ |
| >; |
| }; |
| |
| mcspi1_pins: pinmux_mcspi1_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ |
| OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ |
| OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ |
| OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ |
| >; |
| }; |
| |
| mcspi3_pins: pinmux_mcspi3_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x25dc, PIN_OUTPUT | MUX_MODE1) /* etk_d0.mcspi3_simo gpio14 INPUT | MODE1 */ |
| OMAP3_CORE1_IOPAD(0x25de, PIN_INPUT_PULLUP | MUX_MODE1) /* etk_d1.mcspi3_somi gpio15 INPUT | MODE1 */ |
| OMAP3_CORE1_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE1) /* etk_d2.mcspi3_cs0 gpio16 INPUT | MODE1 */ |
| OMAP3_CORE1_IOPAD(0x25e2, PIN_INPUT | MUX_MODE1) /* etk_d3.mcspi3_clk gpio17 INPUT | MODE1 */ |
| >; |
| }; |
| |
| mcbsp3_pins: pinmux_mcbsp3_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x216c, PIN_OUTPUT | MUX_MODE0) /* mcbsp3_dx.uart2_cts */ |
| OMAP3_CORE1_IOPAD(0x216e, PIN_INPUT | MUX_MODE0) /* mcbsp3_dr.uart2_rts */ |
| OMAP3_CORE1_IOPAD(0x2170, PIN_INPUT | MUX_MODE0) /* mcbsp3_clk.uart2_tx */ |
| OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE0) /* mcbsp3_fsx.uart2_rx */ |
| >; |
| }; |
| }; |
| |
| /* McBSP1: mux'ed with GPIO158 as clock for HA-DSP */ |
| &mcbsp1 { |
| status = "disabled"; |
| }; |
| |
| &mcbsp2 { |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <2600000>; |
| |
| twl: twl@48 { |
| reg = <0x48>; |
| interrupts = <7>; /* SYS_NIRQ cascaded to intc */ |
| interrupt-parent = <&intc>; |
| |
| twl_audio: audio { |
| compatible = "ti,twl4030-audio"; |
| codec { |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <100000>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c3_pins>; |
| }; |
| |
| &mcspi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcspi1_pins>; |
| |
| spidev@0 { |
| compatible = "spidev"; |
| spi-max-frequency = <48000000>; |
| reg = <0>; |
| spi-cpha; |
| }; |
| }; |
| |
| &mcspi3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcspi3_pins>; |
| |
| spidev@0 { |
| compatible = "spidev"; |
| spi-max-frequency = <48000000>; |
| reg = <0>; |
| spi-cpha; |
| }; |
| }; |
| |
| #include "twl4030.dtsi" |
| #include "twl4030_omap3.dtsi" |
| |
| &mmc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc1_pins>; |
| vmmc-supply = <&vmmc1>; |
| vmmc_aux-supply = <&vsim>; |
| cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_HIGH>; |
| bus-width = <8>; |
| }; |
| |
| // WiFi (Marvell 88W8686) on MMC2/SDIO |
| &mmc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc2_pins>; |
| vmmc-supply = <&mmc2_sdio_poweron>; |
| non-removable; |
| bus-width = <4>; |
| cap-power-off-card; |
| }; |
| |
| &mmc3 { |
| status = "disabled"; |
| }; |
| |
| &usbhshost { |
| port2-mode = "ehci-phy"; |
| }; |
| |
| &usbhsehci { |
| phys = <0 &hsusb2_phy>; |
| }; |
| |
| &twl_gpio { |
| ti,use-leds; |
| /* pullups: BIT(1) */ |
| ti,pullups = <0x000002>; |
| /* |
| * pulldowns: |
| * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13) |
| * BIT(15), BIT(16), BIT(17) |
| */ |
| ti,pulldowns = <0x03a1c4>; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart3_pins>; |
| }; |
| |
| &mcbsp3 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcbsp3_pins>; |
| }; |
| |
| &gpmc { |
| ranges = <0 0 0x30000000 0x01000000>; /* CS0: 16MB for NAND */ |
| |
| nand@0,0 { |
| compatible = "ti,omap2-nand"; |
| reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ |
| interrupt-parent = <&gpmc>; |
| interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ |
| <1 IRQ_TYPE_NONE>; /* termcount */ |
| nand-bus-width = <16>; |
| gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */ |
| ti,nand-ecc-opt = "sw"; |
| |
| gpmc,cs-on-ns = <0>; |
| gpmc,cs-rd-off-ns = <36>; |
| gpmc,cs-wr-off-ns = <36>; |
| gpmc,adv-on-ns = <6>; |
| gpmc,adv-rd-off-ns = <24>; |
| gpmc,adv-wr-off-ns = <36>; |
| gpmc,oe-on-ns = <6>; |
| gpmc,oe-off-ns = <48>; |
| gpmc,we-on-ns = <6>; |
| gpmc,we-off-ns = <30>; |
| gpmc,rd-cycle-ns = <72>; |
| gpmc,wr-cycle-ns = <72>; |
| gpmc,access-ns = <54>; |
| gpmc,wr-access-ns = <30>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| x-loader@0 { |
| label = "X-Loader"; |
| reg = <0 0x80000>; |
| }; |
| |
| bootloaders@80000 { |
| label = "U-Boot"; |
| reg = <0x80000 0x1e0000>; |
| }; |
| |
| bootloaders_env@260000 { |
| label = "U-Boot Env"; |
| reg = <0x260000 0x20000>; |
| }; |
| |
| kernel@280000 { |
| label = "Kernel"; |
| reg = <0x280000 0x400000>; |
| }; |
| |
| filesystem@680000 { |
| label = "File System"; |
| reg = <0x680000 0xf980000>; |
| }; |
| }; |
| }; |
| |
| &usb_otg_hs { |
| interface-type = <0>; |
| usb-phy = <&usb2_phy>; |
| phys = <&usb2_phy>; |
| phy-names = "usb2-phy"; |
| mode = <3>; |
| power = <50>; |
| }; |
| |
| &vaux2 { |
| regulator-name = "vdd_ehci"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |