Merge branch 'from-linus' into upstream
diff --git a/Documentation/networking/README.ipw2200 b/Documentation/networking/README.ipw2200
index acb30c5..4f2a40f 100644
--- a/Documentation/networking/README.ipw2200
+++ b/Documentation/networking/README.ipw2200
@@ -14,8 +14,8 @@
README.ipw2200
-Version: 1.0.8
-Date : October 20, 2005
+Version: 1.1.2
+Date : March 30, 2006
Index
@@ -103,7 +103,7 @@
1.1. Overview of Features
-----------------------------------------------
-The current release (1.0.8) supports the following features:
+The current release (1.1.2) supports the following features:
+ BSS mode (Infrastructure, Managed)
+ IBSS mode (Ad-Hoc)
@@ -247,8 +247,8 @@
% cat /sys/bus/pci/drivers/ipw2200/debug_level
Will report the current debug level of the driver's logging subsystem
-(only available if CONFIG_IPW_DEBUG was configured when the driver was
-built).
+(only available if CONFIG_IPW2200_DEBUG was configured when the driver
+was built).
You can set the debug level via:
diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig
index e0874cb..d7691c4 100644
--- a/drivers/net/wireless/Kconfig
+++ b/drivers/net/wireless/Kconfig
@@ -235,7 +235,35 @@
promiscuous mode via the Wireless Tool's Monitor mode. While in this
mode, no packets can be sent.
-config IPW_QOS
+config IPW2200_RADIOTAP
+ bool "Enable radiotap format 802.11 raw packet support"
+ depends on IPW2200_MONITOR
+
+config IPW2200_PROMISCUOUS
+ bool "Enable creation of a RF radiotap promiscuous interface"
+ depends on IPW2200_MONITOR
+ select IPW2200_RADIOTAP
+ ---help---
+ Enables the creation of a second interface prefixed 'rtap'.
+ This second interface will provide every received in radiotap
+ format.
+
+ This is useful for performing wireless network analysis while
+ maintaining an active association.
+
+ Example usage:
+
+ % modprobe ipw2200 rtap_iface=1
+ % ifconfig rtap0 up
+ % tethereal -i rtap0
+
+ If you do not specify 'rtap_iface=1' as a module parameter then
+ the rtap interface will not be created and you will need to turn
+ it on via sysfs:
+
+ % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface
+
+config IPW2200_QOS
bool "Enable QoS support"
depends on IPW2200 && EXPERIMENTAL
diff --git a/drivers/net/wireless/airo.c b/drivers/net/wireless/airo.c
index 00764dd..7f2dacf 100644
--- a/drivers/net/wireless/airo.c
+++ b/drivers/net/wireless/airo.c
@@ -47,6 +47,7 @@
#include <linux/ioport.h>
#include <linux/pci.h>
#include <asm/uaccess.h>
+#include <net/ieee80211.h>
#include "airo.h"
@@ -467,6 +468,8 @@
#define RID_ECHOTEST_RESULTS 0xFF71
#define RID_BSSLISTFIRST 0xFF72
#define RID_BSSLISTNEXT 0xFF73
+#define RID_WPA_BSSLISTFIRST 0xFF74
+#define RID_WPA_BSSLISTNEXT 0xFF75
typedef struct {
u16 cmd;
@@ -739,6 +742,14 @@
u16 extSoftCap;
} CapabilityRid;
+
+/* Only present on firmware >= 5.30.17 */
+typedef struct {
+ u16 unknown[4];
+ u8 fixed[12]; /* WLAN management frame */
+ u8 iep[624];
+} BSSListRidExtra;
+
typedef struct {
u16 len;
u16 index; /* First is 0 and 0xffff means end of list */
@@ -767,6 +778,9 @@
} fh;
u16 dsChannel;
u16 atimWindow;
+
+ /* Only present on firmware >= 5.30.17 */
+ BSSListRidExtra extra;
} BSSListRid;
typedef struct {
@@ -1140,8 +1154,6 @@
char defindex; // Used with auto wep
struct proc_dir_entry *proc_entry;
spinlock_t aux_lock;
- unsigned long flags;
-#define FLAG_PROMISC 8 /* IFF_PROMISC 0x100 - include/linux/if.h */
#define FLAG_RADIO_OFF 0 /* User disabling of MAC */
#define FLAG_RADIO_DOWN 1 /* ifup/ifdown disabling of MAC */
#define FLAG_RADIO_MASK 0x03
@@ -1151,6 +1163,7 @@
#define FLAG_UPDATE_MULTI 5
#define FLAG_UPDATE_UNI 6
#define FLAG_802_11 7
+#define FLAG_PROMISC 8 /* IFF_PROMISC 0x100 - include/linux/if.h */
#define FLAG_PENDING_XMIT 9
#define FLAG_PENDING_XMIT11 10
#define FLAG_MPI 11
@@ -1158,17 +1171,19 @@
#define FLAG_COMMIT 13
#define FLAG_RESET 14
#define FLAG_FLASHING 15
-#define JOB_MASK 0x2ff0000
-#define JOB_DIE 16
-#define JOB_XMIT 17
-#define JOB_XMIT11 18
-#define JOB_STATS 19
-#define JOB_PROMISC 20
-#define JOB_MIC 21
-#define JOB_EVENT 22
-#define JOB_AUTOWEP 23
-#define JOB_WSTATS 24
-#define JOB_SCAN_RESULTS 25
+#define FLAG_WPA_CAPABLE 16
+ unsigned long flags;
+#define JOB_DIE 0
+#define JOB_XMIT 1
+#define JOB_XMIT11 2
+#define JOB_STATS 3
+#define JOB_PROMISC 4
+#define JOB_MIC 5
+#define JOB_EVENT 6
+#define JOB_AUTOWEP 7
+#define JOB_WSTATS 8
+#define JOB_SCAN_RESULTS 9
+ unsigned long jobs;
int (*bap_read)(struct airo_info*, u16 *pu16Dst, int bytelen,
int whichbap);
unsigned short *flash;
@@ -1208,6 +1223,11 @@
#define PCI_SHARED_LEN 2*MPI_MAX_FIDS*PKTSIZE+RIDSIZE
char proc_name[IFNAMSIZ];
+ /* WPA-related stuff */
+ unsigned int bssListFirst;
+ unsigned int bssListNext;
+ unsigned int bssListRidLen;
+
struct list_head network_list;
struct list_head network_free_list;
BSSListElement *networks;
@@ -1264,7 +1284,7 @@
{
MICRid mic_rid;
- clear_bit(JOB_MIC, &ai->flags);
+ clear_bit(JOB_MIC, &ai->jobs);
PC4500_readrid(ai, RID_MIC, &mic_rid, sizeof(mic_rid), 0);
up(&ai->sem);
@@ -1705,24 +1725,24 @@
static int readBSSListRid(struct airo_info *ai, int first,
BSSListRid *list) {
int rc;
- Cmd cmd;
- Resp rsp;
+ Cmd cmd;
+ Resp rsp;
if (first == 1) {
- if (ai->flags & FLAG_RADIO_MASK) return -ENETDOWN;
- memset(&cmd, 0, sizeof(cmd));
- cmd.cmd=CMD_LISTBSS;
- if (down_interruptible(&ai->sem))
- return -ERESTARTSYS;
- issuecommand(ai, &cmd, &rsp);
- up(&ai->sem);
- /* Let the command take effect */
- ai->task = current;
- ssleep(3);
- ai->task = NULL;
- }
- rc = PC4500_readrid(ai, first ? RID_BSSLISTFIRST : RID_BSSLISTNEXT,
- list, sizeof(*list), 1);
+ if (ai->flags & FLAG_RADIO_MASK) return -ENETDOWN;
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.cmd=CMD_LISTBSS;
+ if (down_interruptible(&ai->sem))
+ return -ERESTARTSYS;
+ issuecommand(ai, &cmd, &rsp);
+ up(&ai->sem);
+ /* Let the command take effect */
+ ai->task = current;
+ ssleep(3);
+ ai->task = NULL;
+ }
+ rc = PC4500_readrid(ai, first ? ai->bssListFirst : ai->bssListNext,
+ list, ai->bssListRidLen, 1);
list->len = le16_to_cpu(list->len);
list->index = le16_to_cpu(list->index);
@@ -2112,7 +2132,7 @@
int fid = priv->xmit.fid;
u32 *fids = priv->fids;
- clear_bit(JOB_XMIT, &priv->flags);
+ clear_bit(JOB_XMIT, &priv->jobs);
clear_bit(FLAG_PENDING_XMIT, &priv->flags);
status = transmit_802_3_packet (priv, fids[fid], skb->data);
up(&priv->sem);
@@ -2162,7 +2182,7 @@
if (down_trylock(&priv->sem) != 0) {
set_bit(FLAG_PENDING_XMIT, &priv->flags);
netif_stop_queue(dev);
- set_bit(JOB_XMIT, &priv->flags);
+ set_bit(JOB_XMIT, &priv->jobs);
wake_up_interruptible(&priv->thr_wait);
} else
airo_end_xmit(dev);
@@ -2177,7 +2197,7 @@
int fid = priv->xmit11.fid;
u32 *fids = priv->fids;
- clear_bit(JOB_XMIT11, &priv->flags);
+ clear_bit(JOB_XMIT11, &priv->jobs);
clear_bit(FLAG_PENDING_XMIT11, &priv->flags);
status = transmit_802_11_packet (priv, fids[fid], skb->data);
up(&priv->sem);
@@ -2233,7 +2253,7 @@
if (down_trylock(&priv->sem) != 0) {
set_bit(FLAG_PENDING_XMIT11, &priv->flags);
netif_stop_queue(dev);
- set_bit(JOB_XMIT11, &priv->flags);
+ set_bit(JOB_XMIT11, &priv->jobs);
wake_up_interruptible(&priv->thr_wait);
} else
airo_end_xmit11(dev);
@@ -2244,7 +2264,7 @@
StatsRid stats_rid;
u32 *vals = stats_rid.vals;
- clear_bit(JOB_STATS, &ai->flags);
+ clear_bit(JOB_STATS, &ai->jobs);
if (ai->power.event) {
up(&ai->sem);
return;
@@ -2272,10 +2292,10 @@
{
struct airo_info *local = dev->priv;
- if (!test_bit(JOB_STATS, &local->flags)) {
+ if (!test_bit(JOB_STATS, &local->jobs)) {
/* Get stats out of the card if available */
if (down_trylock(&local->sem) != 0) {
- set_bit(JOB_STATS, &local->flags);
+ set_bit(JOB_STATS, &local->jobs);
wake_up_interruptible(&local->thr_wait);
} else
airo_read_stats(local);
@@ -2290,7 +2310,7 @@
memset(&cmd, 0, sizeof(cmd));
cmd.cmd=CMD_SETMODE;
- clear_bit(JOB_PROMISC, &ai->flags);
+ clear_bit(JOB_PROMISC, &ai->jobs);
cmd.parm0=(ai->flags&IFF_PROMISC) ? PROMISC : NOPROMISC;
issuecommand(ai, &cmd, &rsp);
up(&ai->sem);
@@ -2302,7 +2322,7 @@
if ((dev->flags ^ ai->flags) & IFF_PROMISC) {
change_bit(FLAG_PROMISC, &ai->flags);
if (down_trylock(&ai->sem) != 0) {
- set_bit(JOB_PROMISC, &ai->flags);
+ set_bit(JOB_PROMISC, &ai->jobs);
wake_up_interruptible(&ai->thr_wait);
} else
airo_set_promisc(ai);
@@ -2380,7 +2400,7 @@
}
clear_bit(FLAG_REGISTERED, &ai->flags);
}
- set_bit(JOB_DIE, &ai->flags);
+ set_bit(JOB_DIE, &ai->jobs);
kill_proc(ai->thr_pid, SIGTERM, 1);
wait_for_completion(&ai->thr_exited);
@@ -2701,14 +2721,14 @@
return 0;
}
-#define MAX_NETWORK_COUNT 64
+#define AIRO_MAX_NETWORK_COUNT 64
static int airo_networks_allocate(struct airo_info *ai)
{
if (ai->networks)
return 0;
ai->networks =
- kzalloc(MAX_NETWORK_COUNT * sizeof(BSSListElement),
+ kzalloc(AIRO_MAX_NETWORK_COUNT * sizeof(BSSListElement),
GFP_KERNEL);
if (!ai->networks) {
airo_print_warn(ai->dev->name, "Out of memory allocating beacons");
@@ -2732,11 +2752,33 @@
INIT_LIST_HEAD(&ai->network_free_list);
INIT_LIST_HEAD(&ai->network_list);
- for (i = 0; i < MAX_NETWORK_COUNT; i++)
+ for (i = 0; i < AIRO_MAX_NETWORK_COUNT; i++)
list_add_tail(&ai->networks[i].list,
&ai->network_free_list);
}
+static int airo_test_wpa_capable(struct airo_info *ai)
+{
+ int status;
+ CapabilityRid cap_rid;
+ const char *name = ai->dev->name;
+
+ status = readCapabilityRid(ai, &cap_rid, 1);
+ if (status != SUCCESS) return 0;
+
+ /* Only firmware versions 5.30.17 or better can do WPA */
+ if ((cap_rid.softVer > 0x530)
+ || ((cap_rid.softVer == 0x530) && (cap_rid.softSubVer >= 0x17))) {
+ airo_print_info(name, "WPA is supported.");
+ return 1;
+ }
+
+ /* No WPA support */
+ airo_print_info(name, "WPA unsupported (only firmware versions 5.30.17"
+ " and greater support WPA. Detected %s)", cap_rid.prodVer);
+ return 0;
+}
+
static struct net_device *_init_airo_card( unsigned short irq, int port,
int is_pcmcia, struct pci_dev *pci,
struct device *dmdev )
@@ -2759,6 +2801,7 @@
ai = dev->priv;
ai->wifidev = NULL;
ai->flags = 0;
+ ai->jobs = 0;
ai->dev = dev;
if (pci && (pci->device == 0x5000 || pci->device == 0xa504)) {
airo_print_dbg(dev->name, "Found an MPI350 card");
@@ -2838,6 +2881,18 @@
set_bit(FLAG_FLASHING, &ai->flags);
}
+ /* Test for WPA support */
+ if (airo_test_wpa_capable(ai)) {
+ set_bit(FLAG_WPA_CAPABLE, &ai->flags);
+ ai->bssListFirst = RID_WPA_BSSLISTFIRST;
+ ai->bssListNext = RID_WPA_BSSLISTNEXT;
+ ai->bssListRidLen = sizeof(BSSListRid);
+ } else {
+ ai->bssListFirst = RID_BSSLISTFIRST;
+ ai->bssListNext = RID_BSSLISTNEXT;
+ ai->bssListRidLen = sizeof(BSSListRid) - sizeof(BSSListRidExtra);
+ }
+
rc = register_netdev(dev);
if (rc) {
airo_print_err(dev->name, "Couldn't register_netdev");
@@ -2875,7 +2930,7 @@
err_out_unlink:
del_airo_dev(dev);
err_out_thr:
- set_bit(JOB_DIE, &ai->flags);
+ set_bit(JOB_DIE, &ai->jobs);
kill_proc(ai->thr_pid, SIGTERM, 1);
wait_for_completion(&ai->thr_exited);
err_out_free:
@@ -2933,7 +2988,7 @@
union iwreq_data wrqu;
StatusRid status_rid;
- clear_bit(JOB_EVENT, &ai->flags);
+ clear_bit(JOB_EVENT, &ai->jobs);
PC4500_readrid(ai, RID_STATUS, &status_rid, sizeof(status_rid), 0);
up(&ai->sem);
wrqu.data.length = 0;
@@ -2947,7 +3002,7 @@
static void airo_process_scan_results (struct airo_info *ai) {
union iwreq_data wrqu;
- BSSListRid BSSList;
+ BSSListRid bss;
int rc;
BSSListElement * loop_net;
BSSListElement * tmp_net;
@@ -2960,15 +3015,15 @@
}
/* Try to read the first entry of the scan result */
- rc = PC4500_readrid(ai, RID_BSSLISTFIRST, &BSSList, sizeof(BSSList), 0);
- if((rc) || (BSSList.index == 0xffff)) {
+ rc = PC4500_readrid(ai, ai->bssListFirst, &bss, ai->bssListRidLen, 0);
+ if((rc) || (bss.index == 0xffff)) {
/* No scan results */
goto out;
}
/* Read and parse all entries */
tmp_net = NULL;
- while((!rc) && (BSSList.index != 0xffff)) {
+ while((!rc) && (bss.index != 0xffff)) {
/* Grab a network off the free list */
if (!list_empty(&ai->network_free_list)) {
tmp_net = list_entry(ai->network_free_list.next,
@@ -2977,19 +3032,19 @@
}
if (tmp_net != NULL) {
- memcpy(tmp_net, &BSSList, sizeof(tmp_net->bss));
+ memcpy(tmp_net, &bss, sizeof(tmp_net->bss));
list_add_tail(&tmp_net->list, &ai->network_list);
tmp_net = NULL;
}
/* Read next entry */
- rc = PC4500_readrid(ai, RID_BSSLISTNEXT,
- &BSSList, sizeof(BSSList), 0);
+ rc = PC4500_readrid(ai, ai->bssListNext,
+ &bss, ai->bssListRidLen, 0);
}
out:
ai->scan_timeout = 0;
- clear_bit(JOB_SCAN_RESULTS, &ai->flags);
+ clear_bit(JOB_SCAN_RESULTS, &ai->jobs);
up(&ai->sem);
/* Send an empty event to user space.
@@ -3019,10 +3074,10 @@
/* make swsusp happy with our thread */
try_to_freeze();
- if (test_bit(JOB_DIE, &ai->flags))
+ if (test_bit(JOB_DIE, &ai->jobs))
break;
- if (ai->flags & JOB_MASK) {
+ if (ai->jobs) {
locked = down_interruptible(&ai->sem);
} else {
wait_queue_t wait;
@@ -3031,16 +3086,16 @@
add_wait_queue(&ai->thr_wait, &wait);
for (;;) {
set_current_state(TASK_INTERRUPTIBLE);
- if (ai->flags & JOB_MASK)
+ if (ai->jobs)
break;
if (ai->expires || ai->scan_timeout) {
if (ai->scan_timeout &&
time_after_eq(jiffies,ai->scan_timeout)){
- set_bit(JOB_SCAN_RESULTS,&ai->flags);
+ set_bit(JOB_SCAN_RESULTS, &ai->jobs);
break;
} else if (ai->expires &&
time_after_eq(jiffies,ai->expires)){
- set_bit(JOB_AUTOWEP,&ai->flags);
+ set_bit(JOB_AUTOWEP, &ai->jobs);
break;
}
if (!signal_pending(current)) {
@@ -3069,7 +3124,7 @@
if (locked)
continue;
- if (test_bit(JOB_DIE, &ai->flags)) {
+ if (test_bit(JOB_DIE, &ai->jobs)) {
up(&ai->sem);
break;
}
@@ -3079,23 +3134,23 @@
continue;
}
- if (test_bit(JOB_XMIT, &ai->flags))
+ if (test_bit(JOB_XMIT, &ai->jobs))
airo_end_xmit(dev);
- else if (test_bit(JOB_XMIT11, &ai->flags))
+ else if (test_bit(JOB_XMIT11, &ai->jobs))
airo_end_xmit11(dev);
- else if (test_bit(JOB_STATS, &ai->flags))
+ else if (test_bit(JOB_STATS, &ai->jobs))
airo_read_stats(ai);
- else if (test_bit(JOB_WSTATS, &ai->flags))
+ else if (test_bit(JOB_WSTATS, &ai->jobs))
airo_read_wireless_stats(ai);
- else if (test_bit(JOB_PROMISC, &ai->flags))
+ else if (test_bit(JOB_PROMISC, &ai->jobs))
airo_set_promisc(ai);
- else if (test_bit(JOB_MIC, &ai->flags))
+ else if (test_bit(JOB_MIC, &ai->jobs))
micinit(ai);
- else if (test_bit(JOB_EVENT, &ai->flags))
+ else if (test_bit(JOB_EVENT, &ai->jobs))
airo_send_event(dev);
- else if (test_bit(JOB_AUTOWEP, &ai->flags))
+ else if (test_bit(JOB_AUTOWEP, &ai->jobs))
timer_func(dev);
- else if (test_bit(JOB_SCAN_RESULTS, &ai->flags))
+ else if (test_bit(JOB_SCAN_RESULTS, &ai->jobs))
airo_process_scan_results(ai);
else /* Shouldn't get here, but we make sure to unlock */
up(&ai->sem);
@@ -3133,7 +3188,7 @@
if ( status & EV_MIC ) {
OUT4500( apriv, EVACK, EV_MIC );
if (test_bit(FLAG_MIC_CAPABLE, &apriv->flags)) {
- set_bit(JOB_MIC, &apriv->flags);
+ set_bit(JOB_MIC, &apriv->jobs);
wake_up_interruptible(&apriv->thr_wait);
}
}
@@ -3187,7 +3242,7 @@
set_bit(FLAG_UPDATE_MULTI, &apriv->flags);
if (down_trylock(&apriv->sem) != 0) {
- set_bit(JOB_EVENT, &apriv->flags);
+ set_bit(JOB_EVENT, &apriv->jobs);
wake_up_interruptible(&apriv->thr_wait);
} else
airo_send_event(dev);
@@ -5485,7 +5540,7 @@
up(&apriv->sem);
/* Schedule check to see if the change worked */
- clear_bit(JOB_AUTOWEP, &apriv->flags);
+ clear_bit(JOB_AUTOWEP, &apriv->jobs);
apriv->expires = RUN_AT(HZ*3);
}
@@ -6876,7 +6931,7 @@
}
range->num_txpower = i;
range->txpower_capa = IW_TXPOW_MWATT;
- range->we_version_source = 12;
+ range->we_version_source = 19;
range->we_version_compiled = WIRELESS_EXT;
range->retry_capa = IW_RETRY_LIMIT | IW_RETRY_LIFETIME;
range->retry_flags = IW_RETRY_LIMIT;
@@ -7152,6 +7207,7 @@
u16 capabilities;
char * current_val; /* For rates */
int i;
+ char * buf;
/* First entry *MUST* be the AP MAC address */
iwe.cmd = SIOCGIWAP;
@@ -7238,8 +7294,69 @@
if((current_val - current_ev) > IW_EV_LCP_LEN)
current_ev = current_val;
- /* The other data in the scan result are not really
- * interesting, so for now drop it - Jean II */
+ /* Beacon interval */
+ buf = kmalloc(30, GFP_KERNEL);
+ if (buf) {
+ iwe.cmd = IWEVCUSTOM;
+ sprintf(buf, "bcn_int=%d", bss->beaconInterval);
+ iwe.u.data.length = strlen(buf);
+ current_ev = iwe_stream_add_point(current_ev, end_buf, &iwe, buf);
+ kfree(buf);
+ }
+
+ /* Put WPA/RSN Information Elements into the event stream */
+ if (test_bit(FLAG_WPA_CAPABLE, &ai->flags)) {
+ unsigned int num_null_ies = 0;
+ u16 length = sizeof (bss->extra.iep);
+ struct ieee80211_info_element *info_element =
+ (struct ieee80211_info_element *) &bss->extra.iep;
+
+ while ((length >= sizeof(*info_element)) && (num_null_ies < 2)) {
+ if (sizeof(*info_element) + info_element->len > length) {
+ /* Invalid element, don't continue parsing IE */
+ break;
+ }
+
+ switch (info_element->id) {
+ case MFIE_TYPE_SSID:
+ /* Two zero-length SSID elements
+ * mean we're done parsing elements */
+ if (!info_element->len)
+ num_null_ies++;
+ break;
+
+ case MFIE_TYPE_GENERIC:
+ if (info_element->len >= 4 &&
+ info_element->data[0] == 0x00 &&
+ info_element->data[1] == 0x50 &&
+ info_element->data[2] == 0xf2 &&
+ info_element->data[3] == 0x01) {
+ iwe.cmd = IWEVGENIE;
+ iwe.u.data.length = min(info_element->len + 2,
+ MAX_WPA_IE_LEN);
+ current_ev = iwe_stream_add_point(current_ev, end_buf,
+ &iwe, (char *) info_element);
+ }
+ break;
+
+ case MFIE_TYPE_RSN:
+ iwe.cmd = IWEVGENIE;
+ iwe.u.data.length = min(info_element->len + 2,
+ MAX_WPA_IE_LEN);
+ current_ev = iwe_stream_add_point(current_ev, end_buf,
+ &iwe, (char *) info_element);
+ break;
+
+ default:
+ break;
+ }
+
+ length -= sizeof(*info_element) + info_element->len;
+ info_element =
+ (struct ieee80211_info_element *)&info_element->
+ data[info_element->len];
+ }
+ }
return current_ev;
}
@@ -7521,7 +7638,7 @@
u32 *vals = stats_rid.vals;
/* Get stats out of the card */
- clear_bit(JOB_WSTATS, &local->flags);
+ clear_bit(JOB_WSTATS, &local->jobs);
if (local->power.event) {
up(&local->sem);
return;
@@ -7565,10 +7682,10 @@
{
struct airo_info *local = dev->priv;
- if (!test_bit(JOB_WSTATS, &local->flags)) {
+ if (!test_bit(JOB_WSTATS, &local->jobs)) {
/* Get stats out of the card if available */
if (down_trylock(&local->sem) != 0) {
- set_bit(JOB_WSTATS, &local->flags);
+ set_bit(JOB_WSTATS, &local->jobs);
wake_up_interruptible(&local->thr_wait);
} else
airo_read_wireless_stats(local);
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx.h b/drivers/net/wireless/bcm43xx/bcm43xx.h
index 2e83083..e66fdb1 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx.h
+++ b/drivers/net/wireless/bcm43xx/bcm43xx.h
@@ -645,7 +645,6 @@
unsigned int irq;
void __iomem *mmio_addr;
- unsigned int mmio_len;
/* Do not use the lock directly. Use the bcm43xx_lock* helper
* functions, to be MMIO-safe. */
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c b/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c
index 35a4fcb..7497fb1 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c
@@ -92,7 +92,7 @@
fappend("subsystem_vendor: 0x%04x subsystem_device: 0x%04x\n",
pci_dev->subsystem_vendor, pci_dev->subsystem_device);
fappend("IRQ: %d\n", bcm->irq);
- fappend("mmio_addr: 0x%p mmio_len: %u\n", bcm->mmio_addr, bcm->mmio_len);
+ fappend("mmio_addr: 0x%p\n", bcm->mmio_addr);
fappend("chip_id: 0x%04x chip_rev: 0x%02x\n", bcm->chip_id, bcm->chip_rev);
if ((bcm->core_80211[0].rev >= 3) && (bcm43xx_read32(bcm, 0x0158) & (1 << 16)))
fappend("Radio disabled by hardware!\n");
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_main.c b/drivers/net/wireless/bcm43xx/bcm43xx_main.c
index 9a06e61..1985286 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_main.c
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_main.c
@@ -3288,8 +3288,7 @@
bcm43xx_chipset_detach(bcm);
/* Do _not_ access the chip, after it is detached. */
- iounmap(bcm->mmio_addr);
-
+ pci_iounmap(pci_dev, bcm->mmio_addr);
pci_release_regions(pci_dev);
pci_disable_device(pci_dev);
@@ -3379,40 +3378,26 @@
struct net_device *net_dev = bcm->net_dev;
int err;
int i;
- unsigned long mmio_start, mmio_flags, mmio_len;
u32 coremask;
err = pci_enable_device(pci_dev);
if (err) {
- printk(KERN_ERR PFX "unable to wake up pci device (%i)\n", err);
+ printk(KERN_ERR PFX "pci_enable_device() failed\n");
goto out;
}
- mmio_start = pci_resource_start(pci_dev, 0);
- mmio_flags = pci_resource_flags(pci_dev, 0);
- mmio_len = pci_resource_len(pci_dev, 0);
- if (!(mmio_flags & IORESOURCE_MEM)) {
- printk(KERN_ERR PFX
- "%s, region #0 not an MMIO resource, aborting\n",
- pci_name(pci_dev));
- err = -ENODEV;
- goto err_pci_disable;
- }
err = pci_request_regions(pci_dev, KBUILD_MODNAME);
if (err) {
- printk(KERN_ERR PFX
- "could not access PCI resources (%i)\n", err);
+ printk(KERN_ERR PFX "pci_request_regions() failed\n");
goto err_pci_disable;
}
/* enable PCI bus-mastering */
pci_set_master(pci_dev);
- bcm->mmio_addr = ioremap(mmio_start, mmio_len);
+ bcm->mmio_addr = pci_iomap(pci_dev, 0, ~0UL);
if (!bcm->mmio_addr) {
- printk(KERN_ERR PFX "%s: cannot remap MMIO, aborting\n",
- pci_name(pci_dev));
+ printk(KERN_ERR PFX "pci_iomap() failed\n");
err = -EIO;
goto err_pci_release;
}
- bcm->mmio_len = mmio_len;
net_dev->base_addr = (unsigned long)bcm->mmio_addr;
bcm43xx_pci_read_config16(bcm, PCI_SUBSYSTEM_VENDOR_ID,
@@ -3505,7 +3490,7 @@
err_chipset_detach:
bcm43xx_chipset_detach(bcm);
err_iounmap:
- iounmap(bcm->mmio_addr);
+ pci_iounmap(pci_dev, bcm->mmio_addr);
err_pci_release:
pci_release_regions(pci_dev);
err_pci_disable:
diff --git a/drivers/net/wireless/hermes.c b/drivers/net/wireless/hermes.c
index 346c6fe..2aa2f38 100644
--- a/drivers/net/wireless/hermes.c
+++ b/drivers/net/wireless/hermes.c
@@ -121,12 +121,6 @@
hw->iobase = address;
hw->reg_spacing = reg_spacing;
hw->inten = 0x0;
-
-#ifdef HERMES_DEBUG_BUFFER
- hw->dbufp = 0;
- memset(&hw->dbuf, 0xff, sizeof(hw->dbuf));
- memset(&hw->profile, 0, sizeof(hw->profile));
-#endif
}
int hermes_init(hermes_t *hw)
@@ -347,19 +341,6 @@
reg = hermes_read_reg(hw, oreg);
}
-#ifdef HERMES_DEBUG_BUFFER
- hw->profile[HERMES_BAP_BUSY_TIMEOUT - k]++;
-
- if (k < HERMES_BAP_BUSY_TIMEOUT) {
- struct hermes_debug_entry *e =
- &hw->dbuf[(hw->dbufp++) % HERMES_DEBUG_BUFSIZE];
- e->bap = bap;
- e->id = id;
- e->offset = offset;
- e->cycles = HERMES_BAP_BUSY_TIMEOUT - k;
- }
-#endif
-
if (reg & HERMES_OFFSET_BUSY)
return -ETIMEDOUT;
@@ -419,8 +400,7 @@
}
/* Write a block of data to the chip's buffer, via the
- * BAP. Synchronization/serialization is the caller's problem. len
- * must be even.
+ * BAP. Synchronization/serialization is the caller's problem.
*
* Returns: < 0 on internal failure (errno), 0 on success, > 0 on error from firmware
*/
@@ -430,7 +410,7 @@
int dreg = bap ? HERMES_DATA1 : HERMES_DATA0;
int err = 0;
- if ( (len < 0) || (len % 2) )
+ if (len < 0)
return -EINVAL;
err = hermes_bap_seek(hw, bap, id, offset);
@@ -438,49 +418,12 @@
goto out;
/* Actually do the transfer */
- hermes_write_words(hw, dreg, buf, len/2);
+ hermes_write_bytes(hw, dreg, buf, len);
out:
return err;
}
-/* Write a block of data to the chip's buffer with padding if
- * neccessary, via the BAP. Synchronization/serialization is the
- * caller's problem. len must be even.
- *
- * Returns: < 0 on internal failure (errno), 0 on success, > 0 on error from firmware
- */
-int hermes_bap_pwrite_pad(hermes_t *hw, int bap, const void *buf, unsigned data_len, int len,
- u16 id, u16 offset)
-{
- int dreg = bap ? HERMES_DATA1 : HERMES_DATA0;
- int err = 0;
-
- if (len < 0 || len % 2 || data_len > len)
- return -EINVAL;
-
- err = hermes_bap_seek(hw, bap, id, offset);
- if (err)
- goto out;
-
- /* Transfer all the complete words of data */
- hermes_write_words(hw, dreg, buf, data_len/2);
- /* If there is an odd byte left over pad and transfer it */
- if (data_len & 1) {
- u8 end[2];
- end[1] = 0;
- end[0] = ((unsigned char *)buf)[data_len - 1];
- hermes_write_words(hw, dreg, end, 1);
- data_len ++;
- }
- /* Now send zeros for the padding */
- if (data_len < len)
- hermes_clear_words(hw, dreg, (len - data_len) / 2);
- /* Complete */
- out:
- return err;
-}
-
/* Read a Length-Type-Value record from the card.
*
* If length is NULL, we ignore the length read from the card, and
@@ -553,7 +496,7 @@
count = length - 1;
- hermes_write_words(hw, dreg, value, count);
+ hermes_write_bytes(hw, dreg, value, count << 1);
err = hermes_docmd_wait(hw, HERMES_CMD_ACCESS | HERMES_CMD_WRITE,
rid, NULL);
@@ -568,7 +511,6 @@
EXPORT_SYMBOL(hermes_bap_pread);
EXPORT_SYMBOL(hermes_bap_pwrite);
-EXPORT_SYMBOL(hermes_bap_pwrite_pad);
EXPORT_SYMBOL(hermes_read_ltv);
EXPORT_SYMBOL(hermes_write_ltv);
diff --git a/drivers/net/wireless/hermes.h b/drivers/net/wireless/hermes.h
index 7644f72..8e3f0e3 100644
--- a/drivers/net/wireless/hermes.h
+++ b/drivers/net/wireless/hermes.h
@@ -328,16 +328,6 @@
u8 addr[HERMES_MAX_MULTICAST][ETH_ALEN];
} __attribute__ ((packed));
-// #define HERMES_DEBUG_BUFFER 1
-#define HERMES_DEBUG_BUFSIZE 4096
-struct hermes_debug_entry {
- int bap;
- u16 id, offset;
- int cycles;
-};
-
-#ifdef __KERNEL__
-
/* Timeouts */
#define HERMES_BAP_BUSY_TIMEOUT (10000) /* In iterations of ~1us */
@@ -347,14 +337,7 @@
int reg_spacing;
#define HERMES_16BIT_REGSPACING 0
#define HERMES_32BIT_REGSPACING 1
-
u16 inten; /* Which interrupts should be enabled? */
-
-#ifdef HERMES_DEBUG_BUFFER
- struct hermes_debug_entry dbuf[HERMES_DEBUG_BUFSIZE];
- unsigned long dbufp;
- unsigned long profile[HERMES_BAP_BUSY_TIMEOUT+1];
-#endif
} hermes_t;
/* Register access convenience macros */
@@ -376,8 +359,6 @@
u16 id, u16 offset);
int hermes_bap_pwrite(hermes_t *hw, int bap, const void *buf, int len,
u16 id, u16 offset);
-int hermes_bap_pwrite_pad(hermes_t *hw, int bap, const void *buf,
- unsigned data_len, int len, u16 id, u16 offset);
int hermes_read_ltv(hermes_t *hw, int bap, u16 rid, unsigned buflen,
u16 *length, void *buf);
int hermes_write_ltv(hermes_t *hw, int bap, u16 rid,
@@ -425,10 +406,13 @@
ioread16_rep(hw->iobase + off, buf, count);
}
-static inline void hermes_write_words(struct hermes *hw, int off, const void *buf, unsigned count)
+static inline void hermes_write_bytes(struct hermes *hw, int off,
+ const char *buf, unsigned count)
{
off = off << hw->reg_spacing;
- iowrite16_rep(hw->iobase + off, buf, count);
+ iowrite16_rep(hw->iobase + off, buf, count >> 1);
+ if (unlikely(count & 1))
+ iowrite8(buf[count - 1], hw->iobase + off);
}
static inline void hermes_clear_words(struct hermes *hw, int off, unsigned count)
@@ -462,21 +446,4 @@
return HERMES_WRITE_RECORD(hw, bap, rid, &rec);
}
-#else /* ! __KERNEL__ */
-
-/* These are provided for the benefit of userspace drivers and testing programs
- which use ioperm() or iopl() */
-
-#define hermes_read_reg(base, off) (inw((base) + (off)))
-#define hermes_write_reg(base, off, val) (outw((val), (base) + (off)))
-
-#define hermes_read_regn(base, name) (hermes_read_reg((base), HERMES_##name))
-#define hermes_write_regn(base, name, val) (hermes_write_reg((base), HERMES_##name, (val)))
-
-/* Note that for the next two, the count is in 16-bit words, not bytes */
-#define hermes_read_data(base, off, buf, count) (insw((base) + (off), (buf), (count)))
-#define hermes_write_data(base, off, buf, count) (outsw((base) + (off), (buf), (count)))
-
-#endif /* ! __KERNEL__ */
-
#endif /* _HERMES_H */
diff --git a/drivers/net/wireless/ipw2200.c b/drivers/net/wireless/ipw2200.c
index bca89cf..39f82f2 100644
--- a/drivers/net/wireless/ipw2200.c
+++ b/drivers/net/wireless/ipw2200.c
@@ -33,7 +33,44 @@
#include "ipw2200.h"
#include <linux/version.h>
-#define IPW2200_VERSION "git-1.1.1"
+
+#ifndef KBUILD_EXTMOD
+#define VK "k"
+#else
+#define VK
+#endif
+
+#ifdef CONFIG_IPW2200_DEBUG
+#define VD "d"
+#else
+#define VD
+#endif
+
+#ifdef CONFIG_IPW2200_MONITOR
+#define VM "m"
+#else
+#define VM
+#endif
+
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+#define VP "p"
+#else
+#define VP
+#endif
+
+#ifdef CONFIG_IPW2200_RADIOTAP
+#define VR "r"
+#else
+#define VR
+#endif
+
+#ifdef CONFIG_IPW2200_QOS
+#define VQ "q"
+#else
+#define VQ
+#endif
+
+#define IPW2200_VERSION "1.1.2" VK VD VM VP VR VQ
#define DRV_DESCRIPTION "Intel(R) PRO/Wireless 2200/2915 Network Driver"
#define DRV_COPYRIGHT "Copyright(c) 2003-2006 Intel Corporation"
#define DRV_VERSION IPW2200_VERSION
@@ -46,7 +83,9 @@
MODULE_LICENSE("GPL");
static int cmdlog = 0;
+#ifdef CONFIG_IPW2200_DEBUG
static int debug = 0;
+#endif
static int channel = 0;
static int mode = 0;
@@ -61,8 +100,14 @@
static const char ipw_modes[] = {
'a', 'b', 'g', '?'
};
+static int antenna = CFG_SYS_ANTENNA_BOTH;
-#ifdef CONFIG_IPW_QOS
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+static int rtap_iface = 0; /* def: 0 -- do not create rtap interface */
+#endif
+
+
+#ifdef CONFIG_IPW2200_QOS
static int qos_enable = 0;
static int qos_burst_enable = 0;
static int qos_no_ack_mask = 0;
@@ -126,7 +171,7 @@
*qos_param);
static int ipw_send_qos_info_command(struct ipw_priv *priv, struct ieee80211_qos_information_element
*qos_param);
-#endif /* CONFIG_IPW_QOS */
+#endif /* CONFIG_IPW2200_QOS */
static struct iw_statistics *ipw_get_wireless_stats(struct net_device *dev);
static void ipw_remove_current_network(struct ipw_priv *priv);
@@ -1269,6 +1314,105 @@
static DEVICE_ATTR(cmd_log, S_IRUGO, show_cmd_log, NULL);
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+static void ipw_prom_free(struct ipw_priv *priv);
+static int ipw_prom_alloc(struct ipw_priv *priv);
+static ssize_t store_rtap_iface(struct device *d,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct ipw_priv *priv = dev_get_drvdata(d);
+ int rc = 0;
+
+ if (count < 1)
+ return -EINVAL;
+
+ switch (buf[0]) {
+ case '0':
+ if (!rtap_iface)
+ return count;
+
+ if (netif_running(priv->prom_net_dev)) {
+ IPW_WARNING("Interface is up. Cannot unregister.\n");
+ return count;
+ }
+
+ ipw_prom_free(priv);
+ rtap_iface = 0;
+ break;
+
+ case '1':
+ if (rtap_iface)
+ return count;
+
+ rc = ipw_prom_alloc(priv);
+ if (!rc)
+ rtap_iface = 1;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ if (rc) {
+ IPW_ERROR("Failed to register promiscuous network "
+ "device (error %d).\n", rc);
+ }
+
+ return count;
+}
+
+static ssize_t show_rtap_iface(struct device *d,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct ipw_priv *priv = dev_get_drvdata(d);
+ if (rtap_iface)
+ return sprintf(buf, "%s", priv->prom_net_dev->name);
+ else {
+ buf[0] = '-';
+ buf[1] = '1';
+ buf[2] = '\0';
+ return 3;
+ }
+}
+
+static DEVICE_ATTR(rtap_iface, S_IWUSR | S_IRUSR, show_rtap_iface,
+ store_rtap_iface);
+
+static ssize_t store_rtap_filter(struct device *d,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct ipw_priv *priv = dev_get_drvdata(d);
+
+ if (!priv->prom_priv) {
+ IPW_ERROR("Attempting to set filter without "
+ "rtap_iface enabled.\n");
+ return -EPERM;
+ }
+
+ priv->prom_priv->filter = simple_strtol(buf, NULL, 0);
+
+ IPW_DEBUG_INFO("Setting rtap filter to " BIT_FMT16 "\n",
+ BIT_ARG16(priv->prom_priv->filter));
+
+ return count;
+}
+
+static ssize_t show_rtap_filter(struct device *d,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct ipw_priv *priv = dev_get_drvdata(d);
+ return sprintf(buf, "0x%04X",
+ priv->prom_priv ? priv->prom_priv->filter : 0);
+}
+
+static DEVICE_ATTR(rtap_filter, S_IWUSR | S_IRUSR, show_rtap_filter,
+ store_rtap_filter);
+#endif
+
static ssize_t show_scan_age(struct device *d, struct device_attribute *attr,
char *buf)
{
@@ -2025,16 +2169,11 @@
return ipw_send_cmd_simple(priv, IPW_CMD_HOST_COMPLETE);
}
-static int ipw_send_system_config(struct ipw_priv *priv,
- struct ipw_sys_config *config)
+static int ipw_send_system_config(struct ipw_priv *priv)
{
- if (!priv || !config) {
- IPW_ERROR("Invalid args\n");
- return -1;
- }
-
- return ipw_send_cmd_pdu(priv, IPW_CMD_SYSTEM_CONFIG, sizeof(*config),
- config);
+ return ipw_send_cmd_pdu(priv, IPW_CMD_SYSTEM_CONFIG,
+ sizeof(priv->sys_config),
+ &priv->sys_config);
}
static int ipw_send_ssid(struct ipw_priv *priv, u8 * ssid, int len)
@@ -3104,10 +3243,10 @@
struct ipw_fw {
- u32 ver;
- u32 boot_size;
- u32 ucode_size;
- u32 fw_size;
+ __le32 ver;
+ __le32 boot_size;
+ __le32 ucode_size;
+ __le32 fw_size;
u8 data[0];
};
@@ -3131,8 +3270,8 @@
fw = (void *)(*raw)->data;
- if ((*raw)->size < sizeof(*fw) +
- fw->boot_size + fw->ucode_size + fw->fw_size) {
+ if ((*raw)->size < sizeof(*fw) + le32_to_cpu(fw->boot_size) +
+ le32_to_cpu(fw->ucode_size) + le32_to_cpu(fw->fw_size)) {
IPW_ERROR("%s is too small or corrupt (%zd)\n",
name, (*raw)->size);
return -EINVAL;
@@ -3237,8 +3376,9 @@
fw = (void *)raw->data;
boot_img = &fw->data[0];
- ucode_img = &fw->data[fw->boot_size];
- fw_img = &fw->data[fw->boot_size + fw->ucode_size];
+ ucode_img = &fw->data[le32_to_cpu(fw->boot_size)];
+ fw_img = &fw->data[le32_to_cpu(fw->boot_size) +
+ le32_to_cpu(fw->ucode_size)];
if (rc < 0)
goto error;
@@ -3272,7 +3412,7 @@
IPW_NIC_SRAM_UPPER_BOUND - IPW_NIC_SRAM_LOWER_BOUND);
/* DMA the initial boot firmware into the device */
- rc = ipw_load_firmware(priv, boot_img, fw->boot_size);
+ rc = ipw_load_firmware(priv, boot_img, le32_to_cpu(fw->boot_size));
if (rc < 0) {
IPW_ERROR("Unable to load boot firmware: %d\n", rc);
goto error;
@@ -3294,7 +3434,7 @@
ipw_write32(priv, IPW_INTA_RW, IPW_INTA_BIT_FW_INITIALIZATION_DONE);
/* DMA the ucode into the device */
- rc = ipw_load_ucode(priv, ucode_img, fw->ucode_size);
+ rc = ipw_load_ucode(priv, ucode_img, le32_to_cpu(fw->ucode_size));
if (rc < 0) {
IPW_ERROR("Unable to load ucode: %d\n", rc);
goto error;
@@ -3304,7 +3444,7 @@
ipw_stop_nic(priv);
/* DMA bss firmware into the device */
- rc = ipw_load_firmware(priv, fw_img, fw->fw_size);
+ rc = ipw_load_firmware(priv, fw_img, le32_to_cpu(fw->fw_size));
if (rc < 0) {
IPW_ERROR("Unable to load firmware: %d\n", rc);
goto error;
@@ -3700,7 +3840,17 @@
static void ipw_system_config(void *data)
{
struct ipw_priv *priv = data;
- ipw_send_system_config(priv, &priv->sys_config);
+
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+ if (priv->prom_net_dev && netif_running(priv->prom_net_dev)) {
+ priv->sys_config.accept_all_data_frames = 1;
+ priv->sys_config.accept_non_directed_frames = 1;
+ priv->sys_config.accept_all_mgmt_bcpr = 1;
+ priv->sys_config.accept_all_mgmt_frames = 1;
+ }
+#endif
+
+ ipw_send_system_config(priv);
}
struct ipw_status_code {
@@ -3771,6 +3921,13 @@
memset(avg, 0, sizeof(*avg));
}
+#define DEPTH_RSSI 8
+#define DEPTH_NOISE 16
+static s16 exponential_average(s16 prev_avg, s16 val, u8 depth)
+{
+ return ((depth-1)*prev_avg + val)/depth;
+}
+
static void average_add(struct average *avg, s16 val)
{
avg->sum -= avg->entries[avg->pos];
@@ -3800,8 +3957,8 @@
priv->quality = 0;
average_init(&priv->average_missed_beacons);
- average_init(&priv->average_rssi);
- average_init(&priv->average_noise);
+ priv->exp_avg_rssi = -60;
+ priv->exp_avg_noise = -85 + 0x100;
priv->last_rate = 0;
priv->last_missed_beacons = 0;
@@ -4008,7 +4165,7 @@
IPW_DEBUG_STATS("Tx quality : %3d%% (%u errors, %u packets)\n",
tx_quality, tx_failures_delta, tx_packets_delta);
- rssi = average_value(&priv->average_rssi);
+ rssi = priv->exp_avg_rssi;
signal_quality =
(100 *
(priv->ieee->perfect_rssi - priv->ieee->worst_rssi) *
@@ -4185,7 +4342,7 @@
queue_work(priv->workqueue,
&priv->system_config);
-#ifdef CONFIG_IPW_QOS
+#ifdef CONFIG_IPW2200_QOS
#define IPW_GET_PACKET_STYPE(x) WLAN_FC_GET_STYPE( \
le16_to_cpu(((struct ieee80211_hdr *)(x))->frame_ctl))
if ((priv->status & STATUS_AUTH) &&
@@ -4482,6 +4639,24 @@
&& priv->status & STATUS_ASSOCIATED)
queue_delayed_work(priv->workqueue,
&priv->request_scan, HZ);
+
+ /* Send an empty event to user space.
+ * We don't send the received data on the event because
+ * it would require us to do complex transcoding, and
+ * we want to minimise the work done in the irq handler
+ * Use a request to extract the data.
+ * Also, we generate this even for any scan, regardless
+ * on how the scan was initiated. User space can just
+ * sync on periodic scan to get fresh data...
+ * Jean II */
+ if (x->status == SCAN_COMPLETED_STATUS_COMPLETE) {
+ union iwreq_data wrqu;
+
+ wrqu.data.length = 0;
+ wrqu.data.flags = 0;
+ wireless_send_event(priv->net_dev, SIOCGIWSCAN,
+ &wrqu, NULL);
+ }
break;
}
@@ -4577,11 +4752,10 @@
case HOST_NOTIFICATION_NOISE_STATS:{
if (notif->size == sizeof(u32)) {
- priv->last_noise =
- (u8) (le32_to_cpu(notif->u.noise.value) &
- 0xff);
- average_add(&priv->average_noise,
- priv->last_noise);
+ priv->exp_avg_noise =
+ exponential_average(priv->exp_avg_noise,
+ (u8) (le32_to_cpu(notif->u.noise.value) & 0xff),
+ DEPTH_NOISE);
break;
}
@@ -6170,8 +6344,6 @@
{
/* make sure WPA is enabled */
ipw_wpa_enable(priv, 1);
-
- ipw_disassociate(priv);
}
static int ipw_set_rsn_capa(struct ipw_priv *priv,
@@ -6365,6 +6537,7 @@
case IW_AUTH_WPA_ENABLED:
ret = ipw_wpa_enable(priv, param->value);
+ ipw_disassociate(priv);
break;
case IW_AUTH_RX_UNENCRYPTED_EAPOL:
@@ -6506,7 +6679,7 @@
return 0;
}
-#ifdef CONFIG_IPW_QOS
+#ifdef CONFIG_IPW2200_QOS
/* QoS */
/*
@@ -6853,61 +7026,55 @@
return from_priority_to_tx_queue[priority] - 1;
}
-/*
-* add QoS parameter to the TX command
-*/
-static int ipw_qos_set_tx_queue_command(struct ipw_priv *priv,
- u16 priority,
- struct tfd_data *tfd, u8 unicast)
+static int ipw_is_qos_active(struct net_device *dev,
+ struct sk_buff *skb)
{
- int ret = 0;
- int tx_queue_id = 0;
+ struct ipw_priv *priv = ieee80211_priv(dev);
struct ieee80211_qos_data *qos_data = NULL;
int active, supported;
- unsigned long flags;
+ u8 *daddr = skb->data + ETH_ALEN;
+ int unicast = !is_multicast_ether_addr(daddr);
if (!(priv->status & STATUS_ASSOCIATED))
return 0;
qos_data = &priv->assoc_network->qos_data;
- spin_lock_irqsave(&priv->ieee->lock, flags);
-
if (priv->ieee->iw_mode == IW_MODE_ADHOC) {
if (unicast == 0)
qos_data->active = 0;
else
qos_data->active = qos_data->supported;
}
-
active = qos_data->active;
supported = qos_data->supported;
-
- spin_unlock_irqrestore(&priv->ieee->lock, flags);
-
IPW_DEBUG_QOS("QoS %d network is QoS active %d supported %d "
"unicast %d\n",
priv->qos_data.qos_enable, active, supported, unicast);
- if (active && priv->qos_data.qos_enable) {
- ret = from_priority_to_tx_queue[priority];
- tx_queue_id = ret - 1;
- IPW_DEBUG_QOS("QoS packet priority is %d \n", priority);
- if (priority <= 7) {
- tfd->tx_flags_ext |= DCT_FLAG_EXT_QOS_ENABLED;
- tfd->tfd.tfd_26.mchdr.qos_ctrl = priority;
- tfd->tfd.tfd_26.mchdr.frame_ctl |=
- IEEE80211_STYPE_QOS_DATA;
+ if (active && priv->qos_data.qos_enable)
+ return 1;
- if (priv->qos_data.qos_no_ack_mask &
- (1UL << tx_queue_id)) {
- tfd->tx_flags &= ~DCT_FLAG_ACK_REQD;
- tfd->tfd.tfd_26.mchdr.qos_ctrl |=
- CTRL_QOS_NO_ACK;
- }
- }
+ return 0;
+
+}
+/*
+* add QoS parameter to the TX command
+*/
+static int ipw_qos_set_tx_queue_command(struct ipw_priv *priv,
+ u16 priority,
+ struct tfd_data *tfd)
+{
+ int tx_queue_id = 0;
+
+
+ tx_queue_id = from_priority_to_tx_queue[priority] - 1;
+ tfd->tx_flags_ext |= DCT_FLAG_EXT_QOS_ENABLED;
+
+ if (priv->qos_data.qos_no_ack_mask & (1UL << tx_queue_id)) {
+ tfd->tx_flags &= ~DCT_FLAG_ACK_REQD;
+ tfd->tfd.tfd_26.mchdr.qos_ctrl |= CTRL_QOS_NO_ACK;
}
-
- return ret;
+ return 0;
}
/*
@@ -6977,7 +7144,7 @@
qos_param);
}
-#endif /* CONFIG_IPW_QOS */
+#endif /* CONFIG_IPW2200_QOS */
static int ipw_associate_network(struct ipw_priv *priv,
struct ieee80211_network *network,
@@ -7116,7 +7283,7 @@
else
priv->sys_config.answer_broadcast_ssid_probe = 0;
- err = ipw_send_system_config(priv, &priv->sys_config);
+ err = ipw_send_system_config(priv);
if (err) {
IPW_DEBUG_HC("Attempt to send sys config command failed.\n");
return err;
@@ -7141,7 +7308,7 @@
priv->assoc_network = network;
-#ifdef CONFIG_IPW_QOS
+#ifdef CONFIG_IPW2200_QOS
ipw_qos_association(priv, network);
#endif
@@ -7415,7 +7582,7 @@
}
}
-#ifdef CONFIG_IEEE80211_RADIOTAP
+#ifdef CONFIG_IPW2200_RADIOTAP
static void ipw_handle_data_packet_monitor(struct ipw_priv *priv,
struct ipw_rx_mem_buffer *rxb,
struct ieee80211_rx_stats *stats)
@@ -7432,15 +7599,7 @@
/* Magic struct that slots into the radiotap header -- no reason
* to build this manually element by element, we can write it much
* more efficiently than we can parse it. ORDER MATTERS HERE */
- struct ipw_rt_hdr {
- struct ieee80211_radiotap_header rt_hdr;
- u8 rt_flags; /* radiotap packet flags */
- u8 rt_rate; /* rate in 500kb/s */
- u16 rt_channel; /* channel in mhz */
- u16 rt_chbitmask; /* channel bitfield */
- s8 rt_dbmsignal; /* signal in dbM, kluged to signed */
- u8 rt_antenna; /* antenna number */
- } *ipw_rt;
+ struct ipw_rt_hdr *ipw_rt;
short len = le16_to_cpu(pkt->u.frame.length);
@@ -7494,9 +7653,11 @@
/* Big bitfield of all the fields we provide in radiotap */
ipw_rt->rt_hdr.it_present =
((1 << IEEE80211_RADIOTAP_FLAGS) |
+ (1 << IEEE80211_RADIOTAP_TSFT) |
(1 << IEEE80211_RADIOTAP_RATE) |
(1 << IEEE80211_RADIOTAP_CHANNEL) |
(1 << IEEE80211_RADIOTAP_DBM_ANTSIGNAL) |
+ (1 << IEEE80211_RADIOTAP_DBM_ANTNOISE) |
(1 << IEEE80211_RADIOTAP_ANTENNA));
/* Zero the flags, we'll add to them as we go */
@@ -7582,6 +7743,217 @@
}
#endif
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+#define ieee80211_is_probe_response(fc) \
+ ((fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_MGMT && \
+ (fc & IEEE80211_FCTL_STYPE) == IEEE80211_STYPE_PROBE_RESP )
+
+#define ieee80211_is_management(fc) \
+ ((fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_MGMT)
+
+#define ieee80211_is_control(fc) \
+ ((fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_CTL)
+
+#define ieee80211_is_data(fc) \
+ ((fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_DATA)
+
+#define ieee80211_is_assoc_request(fc) \
+ ((fc & IEEE80211_FCTL_STYPE) == IEEE80211_STYPE_ASSOC_REQ)
+
+#define ieee80211_is_reassoc_request(fc) \
+ ((fc & IEEE80211_FCTL_STYPE) == IEEE80211_STYPE_REASSOC_REQ)
+
+static void ipw_handle_promiscuous_rx(struct ipw_priv *priv,
+ struct ipw_rx_mem_buffer *rxb,
+ struct ieee80211_rx_stats *stats)
+{
+ struct ipw_rx_packet *pkt = (struct ipw_rx_packet *)rxb->skb->data;
+ struct ipw_rx_frame *frame = &pkt->u.frame;
+ struct ipw_rt_hdr *ipw_rt;
+
+ /* First cache any information we need before we overwrite
+ * the information provided in the skb from the hardware */
+ struct ieee80211_hdr *hdr;
+ u16 channel = frame->received_channel;
+ u8 phy_flags = frame->antennaAndPhy;
+ s8 signal = frame->rssi_dbm - IPW_RSSI_TO_DBM;
+ s8 noise = frame->noise;
+ u8 rate = frame->rate;
+ short len = le16_to_cpu(pkt->u.frame.length);
+ u64 tsf = 0;
+ struct sk_buff *skb;
+ int hdr_only = 0;
+ u16 filter = priv->prom_priv->filter;
+
+ /* If the filter is set to not include Rx frames then return */
+ if (filter & IPW_PROM_NO_RX)
+ return;
+
+ /* We received data from the HW, so stop the watchdog */
+ priv->prom_net_dev->trans_start = jiffies;
+
+ if (unlikely((len + IPW_RX_FRAME_SIZE) > skb_tailroom(rxb->skb))) {
+ priv->prom_priv->ieee->stats.rx_errors++;
+ IPW_DEBUG_DROP("Corruption detected! Oh no!\n");
+ return;
+ }
+
+ /* We only process data packets if the interface is open */
+ if (unlikely(!netif_running(priv->prom_net_dev))) {
+ priv->prom_priv->ieee->stats.rx_dropped++;
+ IPW_DEBUG_DROP("Dropping packet while interface is not up.\n");
+ return;
+ }
+
+ /* Libpcap 0.9.3+ can handle variable length radiotap, so we'll use
+ * that now */
+ if (len > IPW_RX_BUF_SIZE - sizeof(struct ipw_rt_hdr)) {
+ /* FIXME: Should alloc bigger skb instead */
+ priv->prom_priv->ieee->stats.rx_dropped++;
+ IPW_DEBUG_DROP("Dropping too large packet in monitor\n");
+ return;
+ }
+
+ hdr = (void *)rxb->skb->data + IPW_RX_FRAME_SIZE;
+ if (ieee80211_is_management(hdr->frame_ctl)) {
+ if (filter & IPW_PROM_NO_MGMT)
+ return;
+ if (filter & IPW_PROM_MGMT_HEADER_ONLY)
+ hdr_only = 1;
+ } else if (ieee80211_is_control(hdr->frame_ctl)) {
+ if (filter & IPW_PROM_NO_CTL)
+ return;
+ if (filter & IPW_PROM_CTL_HEADER_ONLY)
+ hdr_only = 1;
+ } else if (ieee80211_is_data(hdr->frame_ctl)) {
+ if (filter & IPW_PROM_NO_DATA)
+ return;
+ if (filter & IPW_PROM_DATA_HEADER_ONLY)
+ hdr_only = 1;
+ }
+
+ /* Copy the SKB since this is for the promiscuous side */
+ skb = skb_copy(rxb->skb, GFP_ATOMIC);
+ if (skb == NULL) {
+ IPW_ERROR("skb_clone failed for promiscuous copy.\n");
+ return;
+ }
+
+ /* copy the frame data to write after where the radiotap header goes */
+ ipw_rt = (void *)skb->data;
+
+ if (hdr_only)
+ len = ieee80211_get_hdrlen(hdr->frame_ctl);
+
+ memcpy(ipw_rt->payload, hdr, len);
+
+ /* Zero the radiotap static buffer ... We only need to zero the bytes
+ * NOT part of our real header, saves a little time.
+ *
+ * No longer necessary since we fill in all our data. Purge before
+ * merging patch officially.
+ * memset(rxb->skb->data + sizeof(struct ipw_rt_hdr), 0,
+ * IEEE80211_RADIOTAP_HDRLEN - sizeof(struct ipw_rt_hdr));
+ */
+
+ ipw_rt->rt_hdr.it_version = PKTHDR_RADIOTAP_VERSION;
+ ipw_rt->rt_hdr.it_pad = 0; /* always good to zero */
+ ipw_rt->rt_hdr.it_len = sizeof(*ipw_rt); /* total header+data */
+
+ /* Set the size of the skb to the size of the frame */
+ skb_put(skb, ipw_rt->rt_hdr.it_len + len);
+
+ /* Big bitfield of all the fields we provide in radiotap */
+ ipw_rt->rt_hdr.it_present =
+ ((1 << IEEE80211_RADIOTAP_FLAGS) |
+ (1 << IEEE80211_RADIOTAP_TSFT) |
+ (1 << IEEE80211_RADIOTAP_RATE) |
+ (1 << IEEE80211_RADIOTAP_CHANNEL) |
+ (1 << IEEE80211_RADIOTAP_DBM_ANTSIGNAL) |
+ (1 << IEEE80211_RADIOTAP_DBM_ANTNOISE) |
+ (1 << IEEE80211_RADIOTAP_ANTENNA));
+
+ /* Zero the flags, we'll add to them as we go */
+ ipw_rt->rt_flags = 0;
+
+ ipw_rt->rt_tsf = tsf;
+
+ /* Convert to DBM */
+ ipw_rt->rt_dbmsignal = signal;
+ ipw_rt->rt_dbmnoise = noise;
+
+ /* Convert the channel data and set the flags */
+ ipw_rt->rt_channel = cpu_to_le16(ieee80211chan2mhz(channel));
+ if (channel > 14) { /* 802.11a */
+ ipw_rt->rt_chbitmask =
+ cpu_to_le16((IEEE80211_CHAN_OFDM | IEEE80211_CHAN_5GHZ));
+ } else if (phy_flags & (1 << 5)) { /* 802.11b */
+ ipw_rt->rt_chbitmask =
+ cpu_to_le16((IEEE80211_CHAN_CCK | IEEE80211_CHAN_2GHZ));
+ } else { /* 802.11g */
+ ipw_rt->rt_chbitmask =
+ (IEEE80211_CHAN_OFDM | IEEE80211_CHAN_2GHZ);
+ }
+
+ /* set the rate in multiples of 500k/s */
+ switch (rate) {
+ case IPW_TX_RATE_1MB:
+ ipw_rt->rt_rate = 2;
+ break;
+ case IPW_TX_RATE_2MB:
+ ipw_rt->rt_rate = 4;
+ break;
+ case IPW_TX_RATE_5MB:
+ ipw_rt->rt_rate = 10;
+ break;
+ case IPW_TX_RATE_6MB:
+ ipw_rt->rt_rate = 12;
+ break;
+ case IPW_TX_RATE_9MB:
+ ipw_rt->rt_rate = 18;
+ break;
+ case IPW_TX_RATE_11MB:
+ ipw_rt->rt_rate = 22;
+ break;
+ case IPW_TX_RATE_12MB:
+ ipw_rt->rt_rate = 24;
+ break;
+ case IPW_TX_RATE_18MB:
+ ipw_rt->rt_rate = 36;
+ break;
+ case IPW_TX_RATE_24MB:
+ ipw_rt->rt_rate = 48;
+ break;
+ case IPW_TX_RATE_36MB:
+ ipw_rt->rt_rate = 72;
+ break;
+ case IPW_TX_RATE_48MB:
+ ipw_rt->rt_rate = 96;
+ break;
+ case IPW_TX_RATE_54MB:
+ ipw_rt->rt_rate = 108;
+ break;
+ default:
+ ipw_rt->rt_rate = 0;
+ break;
+ }
+
+ /* antenna number */
+ ipw_rt->rt_antenna = (phy_flags & 3);
+
+ /* set the preamble flag if we have it */
+ if (phy_flags & (1 << 6))
+ ipw_rt->rt_flags |= IEEE80211_RADIOTAP_F_SHORTPRE;
+
+ IPW_DEBUG_RX("Rx packet of %d bytes.\n", skb->len);
+
+ if (!ieee80211_rx(priv->prom_priv->ieee, skb, stats)) {
+ priv->prom_priv->ieee->stats.rx_errors++;
+ dev_kfree_skb_any(skb);
+ }
+}
+#endif
+
static int is_network_packet(struct ipw_priv *priv,
struct ieee80211_hdr_4addr *header)
{
@@ -7808,15 +8180,21 @@
priv->rx_packets++;
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+ if (priv->prom_net_dev && netif_running(priv->prom_net_dev))
+ ipw_handle_promiscuous_rx(priv, rxb, &stats);
+#endif
+
#ifdef CONFIG_IPW2200_MONITOR
if (priv->ieee->iw_mode == IW_MODE_MONITOR) {
-#ifdef CONFIG_IEEE80211_RADIOTAP
- ipw_handle_data_packet_monitor(priv,
- rxb,
- &stats);
+#ifdef CONFIG_IPW2200_RADIOTAP
+
+ ipw_handle_data_packet_monitor(priv,
+ rxb,
+ &stats);
#else
- ipw_handle_data_packet(priv, rxb,
- &stats);
+ ipw_handle_data_packet(priv, rxb,
+ &stats);
#endif
break;
}
@@ -7837,9 +8215,9 @@
if (network_packet && priv->assoc_network) {
priv->assoc_network->stats.rssi =
stats.rssi;
- average_add(&priv->average_rssi,
- stats.rssi);
- priv->last_rx_rssi = stats.rssi;
+ priv->exp_avg_rssi =
+ exponential_average(priv->exp_avg_rssi,
+ stats.rssi, DEPTH_RSSI);
}
IPW_DEBUG_RX("Frame: len=%u\n",
@@ -7982,10 +8360,10 @@
IPW_DEBUG_INFO("Bind to static channel %d\n", channel);
/* TODO: Validate that provided channel is in range */
}
-#ifdef CONFIG_IPW_QOS
+#ifdef CONFIG_IPW2200_QOS
ipw_qos_init(priv, qos_enable, qos_burst_enable,
burst_duration_CCK, burst_duration_OFDM);
-#endif /* CONFIG_IPW_QOS */
+#endif /* CONFIG_IPW2200_QOS */
switch (mode) {
case 1:
@@ -7996,7 +8374,7 @@
#ifdef CONFIG_IPW2200_MONITOR
case 2:
priv->ieee->iw_mode = IW_MODE_MONITOR;
-#ifdef CONFIG_IEEE80211_RADIOTAP
+#ifdef CONFIG_IPW2200_RADIOTAP
priv->net_dev->type = ARPHRD_IEEE80211_RADIOTAP;
#else
priv->net_dev->type = ARPHRD_IEEE80211;
@@ -8251,7 +8629,7 @@
priv->net_dev->type = ARPHRD_ETHER;
if (wrqu->mode == IW_MODE_MONITOR)
-#ifdef CONFIG_IEEE80211_RADIOTAP
+#ifdef CONFIG_IPW2200_RADIOTAP
priv->net_dev->type = ARPHRD_IEEE80211_RADIOTAP;
#else
priv->net_dev->type = ARPHRD_IEEE80211;
@@ -8379,7 +8757,8 @@
/* Event capability (kernel + driver) */
range->event_capa[0] = (IW_EVENT_CAPA_K_0 |
IW_EVENT_CAPA_MASK(SIOCGIWTHRSPY) |
- IW_EVENT_CAPA_MASK(SIOCGIWAP));
+ IW_EVENT_CAPA_MASK(SIOCGIWAP) |
+ IW_EVENT_CAPA_MASK(SIOCGIWSCAN));
range->event_capa[1] = IW_EVENT_CAPA_K_1;
range->enc_capa = IW_ENC_CAPA_WPA | IW_ENC_CAPA_WPA2 |
@@ -8734,6 +9113,7 @@
struct ipw_priv *priv = ieee80211_priv(dev);
mutex_lock(&priv->mutex);
wrqu->bitrate.value = priv->last_rate;
+ wrqu->bitrate.fixed = (priv->config & CFG_FIXED_RATE) ? 1 : 0;
mutex_unlock(&priv->mutex);
IPW_DEBUG_WX("GET Rate -> %d \n", wrqu->bitrate.value);
return 0;
@@ -9351,7 +9731,7 @@
IPW_DEBUG_WX("SET MONITOR: %d %d\n", enable, parms[1]);
if (enable) {
if (priv->ieee->iw_mode != IW_MODE_MONITOR) {
-#ifdef CONFIG_IEEE80211_RADIOTAP
+#ifdef CONFIG_IPW2200_RADIOTAP
priv->net_dev->type = ARPHRD_IEEE80211_RADIOTAP;
#else
priv->net_dev->type = ARPHRD_IEEE80211;
@@ -9579,8 +9959,8 @@
}
wstats->qual.qual = priv->quality;
- wstats->qual.level = average_value(&priv->average_rssi);
- wstats->qual.noise = average_value(&priv->average_noise);
+ wstats->qual.level = priv->exp_avg_rssi;
+ wstats->qual.noise = priv->exp_avg_noise;
wstats->qual.updated = IW_QUAL_QUAL_UPDATED | IW_QUAL_LEVEL_UPDATED |
IW_QUAL_NOISE_UPDATED | IW_QUAL_DBM;
@@ -9608,7 +9988,9 @@
sys_config->disable_unicast_decryption = 1;
sys_config->exclude_multicast_unencrypted = 0;
sys_config->disable_multicast_decryption = 1;
- sys_config->antenna_diversity = CFG_SYS_ANTENNA_SLOW_DIV;
+ if (antenna < CFG_SYS_ANTENNA_BOTH || antenna > CFG_SYS_ANTENNA_B)
+ antenna = CFG_SYS_ANTENNA_BOTH;
+ sys_config->antenna_diversity = antenna;
sys_config->pass_crc_to_host = 0; /* TODO: See if 1 gives us FCS */
sys_config->dot11g_auto_detection = 0;
sys_config->enable_cts_to_self = 0;
@@ -9647,11 +10029,11 @@
static int ipw_tx_skb(struct ipw_priv *priv, struct ieee80211_txb *txb,
int pri)
{
- struct ieee80211_hdr_3addr *hdr = (struct ieee80211_hdr_3addr *)
+ struct ieee80211_hdr_3addrqos *hdr = (struct ieee80211_hdr_3addrqos *)
txb->fragments[0]->data;
int i = 0;
struct tfd_frame *tfd;
-#ifdef CONFIG_IPW_QOS
+#ifdef CONFIG_IPW2200_QOS
int tx_id = ipw_get_tx_queue_number(priv, pri);
struct clx2_tx_queue *txq = &priv->txq[tx_id];
#else
@@ -9662,9 +10044,9 @@
u16 remaining_bytes;
int fc;
+ hdr_len = ieee80211_get_hdrlen(le16_to_cpu(hdr->frame_ctl));
switch (priv->ieee->iw_mode) {
case IW_MODE_ADHOC:
- hdr_len = IEEE80211_3ADDR_LEN;
unicast = !is_multicast_ether_addr(hdr->addr1);
id = ipw_find_station(priv, hdr->addr1);
if (id == IPW_INVALID_STATION) {
@@ -9681,7 +10063,6 @@
case IW_MODE_INFRA:
default:
unicast = !is_multicast_ether_addr(hdr->addr3);
- hdr_len = IEEE80211_3ADDR_LEN;
id = 0;
break;
}
@@ -9759,9 +10140,10 @@
/* No hardware encryption */
tfd->u.data.tx_flags |= DCT_FLAG_NO_WEP;
-#ifdef CONFIG_IPW_QOS
- ipw_qos_set_tx_queue_command(priv, pri, &(tfd->u.data), unicast);
-#endif /* CONFIG_IPW_QOS */
+#ifdef CONFIG_IPW2200_QOS
+ if (fc & IEEE80211_STYPE_QOS_DATA)
+ ipw_qos_set_tx_queue_command(priv, pri, &(tfd->u.data));
+#endif /* CONFIG_IPW2200_QOS */
/* payload */
tfd->u.data.num_chunks = cpu_to_le32(min((u8) (NUM_TFD_CHUNKS - 2),
@@ -9841,12 +10223,12 @@
static int ipw_net_is_queue_full(struct net_device *dev, int pri)
{
struct ipw_priv *priv = ieee80211_priv(dev);
-#ifdef CONFIG_IPW_QOS
+#ifdef CONFIG_IPW2200_QOS
int tx_id = ipw_get_tx_queue_number(priv, pri);
struct clx2_tx_queue *txq = &priv->txq[tx_id];
#else
struct clx2_tx_queue *txq = &priv->txq[0];
-#endif /* CONFIG_IPW_QOS */
+#endif /* CONFIG_IPW2200_QOS */
if (ipw_queue_space(&txq->q) < txq->q.high_mark)
return 1;
@@ -9854,6 +10236,88 @@
return 0;
}
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+static void ipw_handle_promiscuous_tx(struct ipw_priv *priv,
+ struct ieee80211_txb *txb)
+{
+ struct ieee80211_rx_stats dummystats;
+ struct ieee80211_hdr *hdr;
+ u8 n;
+ u16 filter = priv->prom_priv->filter;
+ int hdr_only = 0;
+
+ if (filter & IPW_PROM_NO_TX)
+ return;
+
+ memset(&dummystats, 0, sizeof(dummystats));
+
+ /* Filtering of fragment chains is done agains the first fragment */
+ hdr = (void *)txb->fragments[0]->data;
+ if (ieee80211_is_management(hdr->frame_ctl)) {
+ if (filter & IPW_PROM_NO_MGMT)
+ return;
+ if (filter & IPW_PROM_MGMT_HEADER_ONLY)
+ hdr_only = 1;
+ } else if (ieee80211_is_control(hdr->frame_ctl)) {
+ if (filter & IPW_PROM_NO_CTL)
+ return;
+ if (filter & IPW_PROM_CTL_HEADER_ONLY)
+ hdr_only = 1;
+ } else if (ieee80211_is_data(hdr->frame_ctl)) {
+ if (filter & IPW_PROM_NO_DATA)
+ return;
+ if (filter & IPW_PROM_DATA_HEADER_ONLY)
+ hdr_only = 1;
+ }
+
+ for(n=0; n<txb->nr_frags; ++n) {
+ struct sk_buff *src = txb->fragments[n];
+ struct sk_buff *dst;
+ struct ieee80211_radiotap_header *rt_hdr;
+ int len;
+
+ if (hdr_only) {
+ hdr = (void *)src->data;
+ len = ieee80211_get_hdrlen(hdr->frame_ctl);
+ } else
+ len = src->len;
+
+ dst = alloc_skb(
+ len + IEEE80211_RADIOTAP_HDRLEN, GFP_ATOMIC);
+ if (!dst) continue;
+
+ rt_hdr = (void *)skb_put(dst, sizeof(*rt_hdr));
+
+ rt_hdr->it_version = PKTHDR_RADIOTAP_VERSION;
+ rt_hdr->it_pad = 0;
+ rt_hdr->it_present = 0; /* after all, it's just an idea */
+ rt_hdr->it_present |= (1 << IEEE80211_RADIOTAP_CHANNEL);
+
+ *(u16*)skb_put(dst, sizeof(u16)) = cpu_to_le16(
+ ieee80211chan2mhz(priv->channel));
+ if (priv->channel > 14) /* 802.11a */
+ *(u16*)skb_put(dst, sizeof(u16)) =
+ cpu_to_le16(IEEE80211_CHAN_OFDM |
+ IEEE80211_CHAN_5GHZ);
+ else if (priv->ieee->mode == IEEE_B) /* 802.11b */
+ *(u16*)skb_put(dst, sizeof(u16)) =
+ cpu_to_le16(IEEE80211_CHAN_CCK |
+ IEEE80211_CHAN_2GHZ);
+ else /* 802.11g */
+ *(u16*)skb_put(dst, sizeof(u16)) =
+ cpu_to_le16(IEEE80211_CHAN_OFDM |
+ IEEE80211_CHAN_2GHZ);
+
+ rt_hdr->it_len = dst->len;
+
+ memcpy(skb_put(dst, len), src->data, len);
+
+ if (!ieee80211_rx(priv->prom_priv->ieee, dst, &dummystats))
+ dev_kfree_skb_any(dst);
+ }
+}
+#endif
+
static int ipw_net_hard_start_xmit(struct ieee80211_txb *txb,
struct net_device *dev, int pri)
{
@@ -9871,6 +10335,11 @@
goto fail_unlock;
}
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+ if (rtap_iface && netif_running(priv->prom_net_dev))
+ ipw_handle_promiscuous_tx(priv, txb);
+#endif
+
ret = ipw_tx_skb(priv, txb, pri);
if (ret == NETDEV_TX_OK)
__ipw_led_activity_on(priv);
@@ -10169,10 +10638,10 @@
INIT_WORK(&priv->merge_networks,
(void (*)(void *))ipw_merge_adhoc_network, priv);
-#ifdef CONFIG_IPW_QOS
+#ifdef CONFIG_IPW2200_QOS
INIT_WORK(&priv->qos_activate, (void (*)(void *))ipw_bg_qos_activate,
priv);
-#endif /* CONFIG_IPW_QOS */
+#endif /* CONFIG_IPW2200_QOS */
tasklet_init(&priv->irq_tasklet, (void (*)(unsigned long))
ipw_irq_tasklet, (unsigned long)priv);
@@ -10318,12 +10787,21 @@
|= CFG_BT_COEXISTENCE_OOB;
}
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+ if (priv->prom_net_dev && netif_running(priv->prom_net_dev)) {
+ priv->sys_config.accept_all_data_frames = 1;
+ priv->sys_config.accept_non_directed_frames = 1;
+ priv->sys_config.accept_all_mgmt_bcpr = 1;
+ priv->sys_config.accept_all_mgmt_frames = 1;
+ }
+#endif
+
if (priv->ieee->iw_mode == IW_MODE_ADHOC)
priv->sys_config.answer_broadcast_ssid_probe = 1;
else
priv->sys_config.answer_broadcast_ssid_probe = 0;
- if (ipw_send_system_config(priv, &priv->sys_config))
+ if (ipw_send_system_config(priv))
goto error;
init_supported_rates(priv, &priv->rates);
@@ -10335,10 +10813,10 @@
if (ipw_send_rts_threshold(priv, priv->rts_threshold))
goto error;
}
-#ifdef CONFIG_IPW_QOS
+#ifdef CONFIG_IPW2200_QOS
IPW_DEBUG_QOS("QoS: call ipw_qos_activate\n");
ipw_qos_activate(priv, NULL);
-#endif /* CONFIG_IPW_QOS */
+#endif /* CONFIG_IPW2200_QOS */
if (ipw_set_random_seed(priv))
goto error;
@@ -10639,6 +11117,7 @@
if (priv->cmdlog == NULL) {
IPW_ERROR("Error allocating %d command log entries.\n",
cmdlog);
+ return -ENOMEM;
} else {
memset(priv->cmdlog, 0, sizeof(*priv->cmdlog) * cmdlog);
priv->cmdlog_len = cmdlog;
@@ -10860,6 +11339,10 @@
&dev_attr_led.attr,
&dev_attr_speed_scan.attr,
&dev_attr_net_stats.attr,
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+ &dev_attr_rtap_iface.attr,
+ &dev_attr_rtap_filter.attr,
+#endif
NULL
};
@@ -10868,6 +11351,109 @@
.attrs = ipw_sysfs_entries,
};
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+static int ipw_prom_open(struct net_device *dev)
+{
+ struct ipw_prom_priv *prom_priv = ieee80211_priv(dev);
+ struct ipw_priv *priv = prom_priv->priv;
+
+ IPW_DEBUG_INFO("prom dev->open\n");
+ netif_carrier_off(dev);
+ netif_stop_queue(dev);
+
+ if (priv->ieee->iw_mode != IW_MODE_MONITOR) {
+ priv->sys_config.accept_all_data_frames = 1;
+ priv->sys_config.accept_non_directed_frames = 1;
+ priv->sys_config.accept_all_mgmt_bcpr = 1;
+ priv->sys_config.accept_all_mgmt_frames = 1;
+
+ ipw_send_system_config(priv);
+ }
+
+ return 0;
+}
+
+static int ipw_prom_stop(struct net_device *dev)
+{
+ struct ipw_prom_priv *prom_priv = ieee80211_priv(dev);
+ struct ipw_priv *priv = prom_priv->priv;
+
+ IPW_DEBUG_INFO("prom dev->stop\n");
+
+ if (priv->ieee->iw_mode != IW_MODE_MONITOR) {
+ priv->sys_config.accept_all_data_frames = 0;
+ priv->sys_config.accept_non_directed_frames = 0;
+ priv->sys_config.accept_all_mgmt_bcpr = 0;
+ priv->sys_config.accept_all_mgmt_frames = 0;
+
+ ipw_send_system_config(priv);
+ }
+
+ return 0;
+}
+
+static int ipw_prom_hard_start_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+ IPW_DEBUG_INFO("prom dev->xmit\n");
+ netif_stop_queue(dev);
+ return -EOPNOTSUPP;
+}
+
+static struct net_device_stats *ipw_prom_get_stats(struct net_device *dev)
+{
+ struct ipw_prom_priv *prom_priv = ieee80211_priv(dev);
+ return &prom_priv->ieee->stats;
+}
+
+static int ipw_prom_alloc(struct ipw_priv *priv)
+{
+ int rc = 0;
+
+ if (priv->prom_net_dev)
+ return -EPERM;
+
+ priv->prom_net_dev = alloc_ieee80211(sizeof(struct ipw_prom_priv));
+ if (priv->prom_net_dev == NULL)
+ return -ENOMEM;
+
+ priv->prom_priv = ieee80211_priv(priv->prom_net_dev);
+ priv->prom_priv->ieee = netdev_priv(priv->prom_net_dev);
+ priv->prom_priv->priv = priv;
+
+ strcpy(priv->prom_net_dev->name, "rtap%d");
+
+ priv->prom_net_dev->type = ARPHRD_IEEE80211_RADIOTAP;
+ priv->prom_net_dev->open = ipw_prom_open;
+ priv->prom_net_dev->stop = ipw_prom_stop;
+ priv->prom_net_dev->get_stats = ipw_prom_get_stats;
+ priv->prom_net_dev->hard_start_xmit = ipw_prom_hard_start_xmit;
+
+ priv->prom_priv->ieee->iw_mode = IW_MODE_MONITOR;
+
+ rc = register_netdev(priv->prom_net_dev);
+ if (rc) {
+ free_ieee80211(priv->prom_net_dev);
+ priv->prom_net_dev = NULL;
+ return rc;
+ }
+
+ return 0;
+}
+
+static void ipw_prom_free(struct ipw_priv *priv)
+{
+ if (!priv->prom_net_dev)
+ return;
+
+ unregister_netdev(priv->prom_net_dev);
+ free_ieee80211(priv->prom_net_dev);
+
+ priv->prom_net_dev = NULL;
+}
+
+#endif
+
+
static int ipw_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
{
int err = 0;
@@ -10959,11 +11545,12 @@
priv->ieee->set_security = shim__set_security;
priv->ieee->is_queue_full = ipw_net_is_queue_full;
-#ifdef CONFIG_IPW_QOS
+#ifdef CONFIG_IPW2200_QOS
+ priv->ieee->is_qos_active = ipw_is_qos_active;
priv->ieee->handle_probe_response = ipw_handle_beacon;
priv->ieee->handle_beacon = ipw_handle_probe_response;
priv->ieee->handle_assoc_response = ipw_handle_assoc_response;
-#endif /* CONFIG_IPW_QOS */
+#endif /* CONFIG_IPW2200_QOS */
priv->ieee->perfect_rssi = -20;
priv->ieee->worst_rssi = -85;
@@ -10997,6 +11584,18 @@
goto out_remove_sysfs;
}
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+ if (rtap_iface) {
+ err = ipw_prom_alloc(priv);
+ if (err) {
+ IPW_ERROR("Failed to register promiscuous network "
+ "device (error %d).\n", err);
+ unregister_netdev(priv->net_dev);
+ goto out_remove_sysfs;
+ }
+ }
+#endif
+
printk(KERN_INFO DRV_NAME ": Detected geography %s (%d 802.11bg "
"channels, %d 802.11a channels)\n",
priv->ieee->geo.name, priv->ieee->geo.bg_channels,
@@ -11076,6 +11675,10 @@
priv->error = NULL;
}
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+ ipw_prom_free(priv);
+#endif
+
free_irq(pdev->irq, priv);
iounmap(priv->hw_base);
pci_release_regions(pdev);
@@ -11200,7 +11803,12 @@
module_param(channel, int, 0444);
MODULE_PARM_DESC(channel, "channel to limit associate to (default 0 [ANY])");
-#ifdef CONFIG_IPW_QOS
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+module_param(rtap_iface, int, 0444);
+MODULE_PARM_DESC(rtap_iface, "create the rtap interface (1 - create, default 0)");
+#endif
+
+#ifdef CONFIG_IPW2200_QOS
module_param(qos_enable, int, 0444);
MODULE_PARM_DESC(qos_enable, "enable all QoS functionalitis");
@@ -11215,7 +11823,7 @@
module_param(burst_duration_OFDM, int, 0444);
MODULE_PARM_DESC(burst_duration_OFDM, "set OFDM burst value");
-#endif /* CONFIG_IPW_QOS */
+#endif /* CONFIG_IPW2200_QOS */
#ifdef CONFIG_IPW2200_MONITOR
module_param(mode, int, 0444);
@@ -11238,5 +11846,8 @@
module_param(roaming, int, 0444);
MODULE_PARM_DESC(roaming, "enable roaming support (default on)");
+module_param(antenna, int, 0444);
+MODULE_PARM_DESC(antenna, "select antenna 1=Main, 3=Aux, default 0 [both], 2=slow_diversity (choose the one with lower background noise)");
+
module_exit(ipw_exit);
module_init(ipw_init);
diff --git a/drivers/net/wireless/ipw2200.h b/drivers/net/wireless/ipw2200.h
index 4b98049..6044c0b 100644
--- a/drivers/net/wireless/ipw2200.h
+++ b/drivers/net/wireless/ipw2200.h
@@ -789,7 +789,7 @@
u8 bt_coexist_collision_thr;
u8 silence_threshold;
u8 accept_all_mgmt_bcpr;
- u8 accept_all_mgtm_frames;
+ u8 accept_all_mgmt_frames;
u8 pass_noise_stats_to_host;
u8 reserved3;
} __attribute__ ((packed));
@@ -1122,6 +1122,52 @@
u8 payload[0];
} __attribute__ ((packed));
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+
+enum ipw_prom_filter {
+ IPW_PROM_CTL_HEADER_ONLY = (1 << 0),
+ IPW_PROM_MGMT_HEADER_ONLY = (1 << 1),
+ IPW_PROM_DATA_HEADER_ONLY = (1 << 2),
+ IPW_PROM_ALL_HEADER_ONLY = 0xf, /* bits 0..3 */
+ IPW_PROM_NO_TX = (1 << 4),
+ IPW_PROM_NO_RX = (1 << 5),
+ IPW_PROM_NO_CTL = (1 << 6),
+ IPW_PROM_NO_MGMT = (1 << 7),
+ IPW_PROM_NO_DATA = (1 << 8),
+};
+
+struct ipw_priv;
+struct ipw_prom_priv {
+ struct ipw_priv *priv;
+ struct ieee80211_device *ieee;
+ enum ipw_prom_filter filter;
+ int tx_packets;
+ int rx_packets;
+};
+#endif
+
+#if defined(CONFIG_IPW2200_RADIOTAP) || defined(CONFIG_IPW2200_PROMISCUOUS)
+/* Magic struct that slots into the radiotap header -- no reason
+ * to build this manually element by element, we can write it much
+ * more efficiently than we can parse it. ORDER MATTERS HERE
+ *
+ * When sent to us via the simulated Rx interface in sysfs, the entire
+ * structure is provided regardless of any bits unset.
+ */
+struct ipw_rt_hdr {
+ struct ieee80211_radiotap_header rt_hdr;
+ u64 rt_tsf; /* TSF */
+ u8 rt_flags; /* radiotap packet flags */
+ u8 rt_rate; /* rate in 500kb/s */
+ u16 rt_channel; /* channel in mhz */
+ u16 rt_chbitmask; /* channel bitfield */
+ s8 rt_dbmsignal; /* signal in dbM, kluged to signed */
+ s8 rt_dbmnoise;
+ u8 rt_antenna; /* antenna number */
+ u8 payload[0]; /* payload... */
+} __attribute__ ((packed));
+#endif
+
struct ipw_priv {
/* ieee device used by generic ieee processing code */
struct ieee80211_device *ieee;
@@ -1133,6 +1179,12 @@
struct pci_dev *pci_dev;
struct net_device *net_dev;
+#ifdef CONFIG_IPW2200_PROMISCUOUS
+ /* Promiscuous mode */
+ struct ipw_prom_priv *prom_priv;
+ struct net_device *prom_net_dev;
+#endif
+
/* pci hardware address support */
void __iomem *hw_base;
unsigned long hw_len;
@@ -1153,11 +1205,9 @@
u32 config;
u32 capability;
- u8 last_rx_rssi;
- u8 last_noise;
struct average average_missed_beacons;
- struct average average_rssi;
- struct average average_noise;
+ s16 exp_avg_rssi;
+ s16 exp_avg_noise;
u32 port_type;
int rx_bufs_min; /**< minimum number of bufs in Rx queue */
int rx_pend_max; /**< maximum pending buffers for one IRQ */
@@ -1308,6 +1358,29 @@
/* debug macros */
+/* Debug and printf string expansion helpers for printing bitfields */
+#define BIT_FMT8 "%c%c%c%c-%c%c%c%c"
+#define BIT_FMT16 BIT_FMT8 ":" BIT_FMT8
+#define BIT_FMT32 BIT_FMT16 " " BIT_FMT16
+
+#define BITC(x,y) (((x>>y)&1)?'1':'0')
+#define BIT_ARG8(x) \
+BITC(x,7),BITC(x,6),BITC(x,5),BITC(x,4),\
+BITC(x,3),BITC(x,2),BITC(x,1),BITC(x,0)
+
+#define BIT_ARG16(x) \
+BITC(x,15),BITC(x,14),BITC(x,13),BITC(x,12),\
+BITC(x,11),BITC(x,10),BITC(x,9),BITC(x,8),\
+BIT_ARG8(x)
+
+#define BIT_ARG32(x) \
+BITC(x,31),BITC(x,30),BITC(x,29),BITC(x,28),\
+BITC(x,27),BITC(x,26),BITC(x,25),BITC(x,24),\
+BITC(x,23),BITC(x,22),BITC(x,21),BITC(x,20),\
+BITC(x,19),BITC(x,18),BITC(x,17),BITC(x,16),\
+BIT_ARG16(x)
+
+
#ifdef CONFIG_IPW2200_DEBUG
#define IPW_DEBUG(level, fmt, args...) \
do { if (ipw_debug_level & (level)) \
diff --git a/drivers/net/wireless/orinoco.c b/drivers/net/wireless/orinoco.c
index 06523e2..d4c13ff 100644
--- a/drivers/net/wireless/orinoco.c
+++ b/drivers/net/wireless/orinoco.c
@@ -201,41 +201,12 @@
/* Data types */
/********************************************************************/
-/* Used in Event handling.
- * We avoid nested structures as they break on ARM -- Moustafa */
-struct hermes_tx_descriptor_802_11 {
- /* hermes_tx_descriptor */
- __le16 status;
- __le16 reserved1;
- __le16 reserved2;
- __le32 sw_support;
- u8 retry_count;
- u8 tx_rate;
- __le16 tx_control;
-
- /* ieee80211_hdr */
+/* Beginning of the Tx descriptor, used in TxExc handling */
+struct hermes_txexc_data {
+ struct hermes_tx_descriptor desc;
__le16 frame_ctl;
__le16 duration_id;
u8 addr1[ETH_ALEN];
- u8 addr2[ETH_ALEN];
- u8 addr3[ETH_ALEN];
- __le16 seq_ctl;
- u8 addr4[ETH_ALEN];
-
- __le16 data_len;
-
- /* ethhdr */
- u8 h_dest[ETH_ALEN]; /* destination eth addr */
- u8 h_source[ETH_ALEN]; /* source ether addr */
- __be16 h_proto; /* packet type ID field */
-
- /* p8022_hdr */
- u8 dsap;
- u8 ssap;
- u8 ctrl;
- u8 oui[3];
-
- __be16 ethertype;
} __attribute__ ((packed));
/* Rx frame header except compatibility 802.3 header */
@@ -450,53 +421,39 @@
hermes_t *hw = &priv->hw;
int err = 0;
u16 txfid = priv->txfid;
- char *p;
struct ethhdr *eh;
- int len, data_len, data_off;
+ int data_off;
struct hermes_tx_descriptor desc;
unsigned long flags;
- TRACE_ENTER(dev->name);
-
if (! netif_running(dev)) {
printk(KERN_ERR "%s: Tx on stopped device!\n",
dev->name);
- TRACE_EXIT(dev->name);
- return 1;
+ return NETDEV_TX_BUSY;
}
if (netif_queue_stopped(dev)) {
printk(KERN_DEBUG "%s: Tx while transmitter busy!\n",
dev->name);
- TRACE_EXIT(dev->name);
- return 1;
+ return NETDEV_TX_BUSY;
}
if (orinoco_lock(priv, &flags) != 0) {
printk(KERN_ERR "%s: orinoco_xmit() called while hw_unavailable\n",
dev->name);
- TRACE_EXIT(dev->name);
- return 1;
+ return NETDEV_TX_BUSY;
}
if (! netif_carrier_ok(dev) || (priv->iw_mode == IW_MODE_MONITOR)) {
/* Oops, the firmware hasn't established a connection,
silently drop the packet (this seems to be the
safest approach). */
- stats->tx_errors++;
- orinoco_unlock(priv, &flags);
- dev_kfree_skb(skb);
- TRACE_EXIT(dev->name);
- return 0;
+ goto drop;
}
- /* Length of the packet body */
- /* FIXME: what if the skb is smaller than this? */
- len = max_t(int, ALIGN(skb->len, 2), ETH_ZLEN);
- skb = skb_padto(skb, len);
- if (skb == NULL)
- goto fail;
- len -= ETH_HLEN;
+ /* Check packet length */
+ if (skb->len < ETH_HLEN)
+ goto drop;
eh = (struct ethhdr *)skb->data;
@@ -507,8 +464,7 @@
if (net_ratelimit())
printk(KERN_ERR "%s: Error %d writing Tx descriptor "
"to BAP\n", dev->name, err);
- stats->tx_errors++;
- goto fail;
+ goto busy;
}
/* Clear the 802.11 header and data length fields - some
@@ -519,50 +475,38 @@
/* Encapsulate Ethernet-II frames */
if (ntohs(eh->h_proto) > ETH_DATA_LEN) { /* Ethernet-II frame */
- struct header_struct hdr;
- data_len = len;
- data_off = HERMES_802_3_OFFSET + sizeof(hdr);
- p = skb->data + ETH_HLEN;
+ struct header_struct {
+ struct ethhdr eth; /* 802.3 header */
+ u8 encap[6]; /* 802.2 header */
+ } __attribute__ ((packed)) hdr;
- /* 802.3 header */
- memcpy(hdr.dest, eh->h_dest, ETH_ALEN);
- memcpy(hdr.src, eh->h_source, ETH_ALEN);
- hdr.len = htons(data_len + ENCAPS_OVERHEAD);
-
- /* 802.2 header */
- memcpy(&hdr.dsap, &encaps_hdr, sizeof(encaps_hdr));
-
- hdr.ethertype = eh->h_proto;
- err = hermes_bap_pwrite(hw, USER_BAP, &hdr, sizeof(hdr),
- txfid, HERMES_802_3_OFFSET);
+ /* Strip destination and source from the data */
+ skb_pull(skb, 2 * ETH_ALEN);
+ data_off = HERMES_802_2_OFFSET + sizeof(encaps_hdr);
+
+ /* And move them to a separate header */
+ memcpy(&hdr.eth, eh, 2 * ETH_ALEN);
+ hdr.eth.h_proto = htons(sizeof(encaps_hdr) + skb->len);
+ memcpy(hdr.encap, encaps_hdr, sizeof(encaps_hdr));
+
+ err = hermes_bap_pwrite(hw, USER_BAP, &hdr, sizeof(hdr),
+ txfid, HERMES_802_3_OFFSET);
if (err) {
if (net_ratelimit())
printk(KERN_ERR "%s: Error %d writing packet "
"header to BAP\n", dev->name, err);
- stats->tx_errors++;
- goto fail;
+ goto busy;
}
- /* Actual xfer length - allow for padding */
- len = ALIGN(data_len, 2);
- if (len < ETH_ZLEN - ETH_HLEN)
- len = ETH_ZLEN - ETH_HLEN;
} else { /* IEEE 802.3 frame */
- data_len = len + ETH_HLEN;
data_off = HERMES_802_3_OFFSET;
- p = skb->data;
- /* Actual xfer length - round up for odd length packets */
- len = ALIGN(data_len, 2);
- if (len < ETH_ZLEN)
- len = ETH_ZLEN;
}
- err = hermes_bap_pwrite_pad(hw, USER_BAP, p, data_len, len,
+ err = hermes_bap_pwrite(hw, USER_BAP, skb->data, skb->len,
txfid, data_off);
if (err) {
printk(KERN_ERR "%s: Error %d writing packet to BAP\n",
dev->name, err);
- stats->tx_errors++;
- goto fail;
+ goto busy;
}
/* Finally, we actually initiate the send */
@@ -575,25 +519,27 @@
if (net_ratelimit())
printk(KERN_ERR "%s: Error %d transmitting packet\n",
dev->name, err);
- stats->tx_errors++;
- goto fail;
+ goto busy;
}
dev->trans_start = jiffies;
- stats->tx_bytes += data_off + data_len;
+ stats->tx_bytes += data_off + skb->len;
+ goto ok;
+ drop:
+ stats->tx_errors++;
+ stats->tx_dropped++;
+
+ ok:
orinoco_unlock(priv, &flags);
-
dev_kfree_skb(skb);
+ return NETDEV_TX_OK;
- TRACE_EXIT(dev->name);
-
- return 0;
- fail:
- TRACE_EXIT(dev->name);
-
+ busy:
+ if (err == -EIO)
+ schedule_work(&priv->reset_work);
orinoco_unlock(priv, &flags);
- return err;
+ return NETDEV_TX_BUSY;
}
static void __orinoco_ev_alloc(struct net_device *dev, hermes_t *hw)
@@ -629,7 +575,7 @@
struct net_device_stats *stats = &priv->stats;
u16 fid = hermes_read_regn(hw, TXCOMPLFID);
u16 status;
- struct hermes_tx_descriptor_802_11 hdr;
+ struct hermes_txexc_data hdr;
int err = 0;
if (fid == DUMMY_FID)
@@ -637,8 +583,7 @@
/* Read part of the frame header - we need status and addr1 */
err = hermes_bap_pread(hw, IRQ_BAP, &hdr,
- offsetof(struct hermes_tx_descriptor_802_11,
- addr2),
+ sizeof(struct hermes_txexc_data),
fid, 0);
hermes_write_regn(hw, TXCOMPLFID, DUMMY_FID);
@@ -658,7 +603,7 @@
* exceeded, because that's the only status that really mean
* that this particular node went away.
* Other errors means that *we* screwed up. - Jean II */
- status = le16_to_cpu(hdr.status);
+ status = le16_to_cpu(hdr.desc.status);
if (status & (HERMES_TXSTAT_RETRYERR | HERMES_TXSTAT_AGEDERR)) {
union iwreq_data wrqu;
@@ -1400,16 +1345,12 @@
return 0;
}
-int orinoco_reinit_firmware(struct net_device *dev)
+static int orinoco_allocate_fid(struct net_device *dev)
{
struct orinoco_private *priv = netdev_priv(dev);
struct hermes *hw = &priv->hw;
int err;
- err = hermes_init(hw);
- if (err)
- return err;
-
err = hermes_allocate(hw, priv->nicbuf_size, &priv->txfid);
if (err == -EIO && priv->nicbuf_size > TX_NICBUF_SIZE_BUG) {
/* Try workaround for old Symbol firmware bug */
@@ -1428,6 +1369,19 @@
return err;
}
+int orinoco_reinit_firmware(struct net_device *dev)
+{
+ struct orinoco_private *priv = netdev_priv(dev);
+ struct hermes *hw = &priv->hw;
+ int err;
+
+ err = hermes_init(hw);
+ if (!err)
+ err = orinoco_allocate_fid(dev);
+
+ return err;
+}
+
static int __orinoco_hw_set_bitrate(struct orinoco_private *priv)
{
hermes_t *hw = &priv->hw;
@@ -2274,14 +2228,12 @@
u16 reclen;
int len;
- TRACE_ENTER(dev->name);
-
/* No need to lock, the hw_unavailable flag is already set in
* alloc_orinocodev() */
priv->nicbuf_size = IEEE80211_FRAME_LEN + ETH_HLEN;
/* Initialize the firmware */
- err = orinoco_reinit_firmware(dev);
+ err = hermes_init(hw);
if (err != 0) {
printk(KERN_ERR "%s: failed to initialize firmware (err = %d)\n",
dev->name, err);
@@ -2339,6 +2291,13 @@
printk(KERN_DEBUG "%s: Station name \"%s\"\n", dev->name, priv->nick);
+ err = orinoco_allocate_fid(dev);
+ if (err) {
+ printk(KERN_ERR "%s: failed to allocate NIC buffer!\n",
+ dev->name);
+ goto out;
+ }
+
/* Get allowed channels */
err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CHANNELLIST,
&priv->channel_mask);
@@ -2429,7 +2388,6 @@
printk(KERN_DEBUG "%s: ready\n", dev->name);
out:
- TRACE_EXIT(dev->name);
return err;
}
@@ -2797,8 +2755,6 @@
int numrates;
int i, k;
- TRACE_ENTER(dev->name);
-
rrq->length = sizeof(struct iw_range);
memset(range, 0, sizeof(struct iw_range));
@@ -2888,8 +2844,6 @@
IW_EVENT_CAPA_SET(range->event_capa, SIOCGIWSCAN);
IW_EVENT_CAPA_SET(range->event_capa, IWEVTXDROP);
- TRACE_EXIT(dev->name);
-
return 0;
}
@@ -3071,8 +3025,6 @@
int err = 0;
unsigned long flags;
- TRACE_ENTER(dev->name);
-
if (netif_running(dev)) {
err = orinoco_hw_get_essid(priv, &active, essidbuf);
if (err)
@@ -3087,8 +3039,6 @@
erq->flags = 1;
erq->length = strlen(essidbuf) + 1;
- TRACE_EXIT(dev->name);
-
return 0;
}
@@ -4349,69 +4299,6 @@
};
/********************************************************************/
-/* Debugging */
-/********************************************************************/
-
-#if 0
-static void show_rx_frame(struct orinoco_rxframe_hdr *frame)
-{
- printk(KERN_DEBUG "RX descriptor:\n");
- printk(KERN_DEBUG " status = 0x%04x\n", frame->desc.status);
- printk(KERN_DEBUG " time = 0x%08x\n", frame->desc.time);
- printk(KERN_DEBUG " silence = 0x%02x\n", frame->desc.silence);
- printk(KERN_DEBUG " signal = 0x%02x\n", frame->desc.signal);
- printk(KERN_DEBUG " rate = 0x%02x\n", frame->desc.rate);
- printk(KERN_DEBUG " rxflow = 0x%02x\n", frame->desc.rxflow);
- printk(KERN_DEBUG " reserved = 0x%08x\n", frame->desc.reserved);
-
- printk(KERN_DEBUG "IEEE 802.11 header:\n");
- printk(KERN_DEBUG " frame_ctl = 0x%04x\n",
- frame->p80211.frame_ctl);
- printk(KERN_DEBUG " duration_id = 0x%04x\n",
- frame->p80211.duration_id);
- printk(KERN_DEBUG " addr1 = %02x:%02x:%02x:%02x:%02x:%02x\n",
- frame->p80211.addr1[0], frame->p80211.addr1[1],
- frame->p80211.addr1[2], frame->p80211.addr1[3],
- frame->p80211.addr1[4], frame->p80211.addr1[5]);
- printk(KERN_DEBUG " addr2 = %02x:%02x:%02x:%02x:%02x:%02x\n",
- frame->p80211.addr2[0], frame->p80211.addr2[1],
- frame->p80211.addr2[2], frame->p80211.addr2[3],
- frame->p80211.addr2[4], frame->p80211.addr2[5]);
- printk(KERN_DEBUG " addr3 = %02x:%02x:%02x:%02x:%02x:%02x\n",
- frame->p80211.addr3[0], frame->p80211.addr3[1],
- frame->p80211.addr3[2], frame->p80211.addr3[3],
- frame->p80211.addr3[4], frame->p80211.addr3[5]);
- printk(KERN_DEBUG " seq_ctl = 0x%04x\n",
- frame->p80211.seq_ctl);
- printk(KERN_DEBUG " addr4 = %02x:%02x:%02x:%02x:%02x:%02x\n",
- frame->p80211.addr4[0], frame->p80211.addr4[1],
- frame->p80211.addr4[2], frame->p80211.addr4[3],
- frame->p80211.addr4[4], frame->p80211.addr4[5]);
- printk(KERN_DEBUG " data_len = 0x%04x\n",
- frame->p80211.data_len);
-
- printk(KERN_DEBUG "IEEE 802.3 header:\n");
- printk(KERN_DEBUG " dest = %02x:%02x:%02x:%02x:%02x:%02x\n",
- frame->p8023.h_dest[0], frame->p8023.h_dest[1],
- frame->p8023.h_dest[2], frame->p8023.h_dest[3],
- frame->p8023.h_dest[4], frame->p8023.h_dest[5]);
- printk(KERN_DEBUG " src = %02x:%02x:%02x:%02x:%02x:%02x\n",
- frame->p8023.h_source[0], frame->p8023.h_source[1],
- frame->p8023.h_source[2], frame->p8023.h_source[3],
- frame->p8023.h_source[4], frame->p8023.h_source[5]);
- printk(KERN_DEBUG " len = 0x%04x\n", frame->p8023.h_proto);
-
- printk(KERN_DEBUG "IEEE 802.2 LLC/SNAP header:\n");
- printk(KERN_DEBUG " DSAP = 0x%02x\n", frame->p8022.dsap);
- printk(KERN_DEBUG " SSAP = 0x%02x\n", frame->p8022.ssap);
- printk(KERN_DEBUG " ctrl = 0x%02x\n", frame->p8022.ctrl);
- printk(KERN_DEBUG " OUI = %02x:%02x:%02x\n",
- frame->p8022.oui[0], frame->p8022.oui[1], frame->p8022.oui[2]);
- printk(KERN_DEBUG " ethertype = 0x%04x\n", frame->ethertype);
-}
-#endif /* 0 */
-
-/********************************************************************/
/* Module initialization */
/********************************************************************/
diff --git a/drivers/net/wireless/orinoco.h b/drivers/net/wireless/orinoco.h
index f5d856d..16db3e1 100644
--- a/drivers/net/wireless/orinoco.h
+++ b/drivers/net/wireless/orinoco.h
@@ -7,7 +7,7 @@
#ifndef _ORINOCO_H
#define _ORINOCO_H
-#define DRIVER_VERSION "0.15rc3"
+#define DRIVER_VERSION "0.15"
#include <linux/netdevice.h>
#include <linux/wireless.h>
@@ -30,20 +30,6 @@
char data[ORINOCO_MAX_KEY_SIZE];
} __attribute__ ((packed));
-struct header_struct {
- /* 802.3 */
- u8 dest[ETH_ALEN];
- u8 src[ETH_ALEN];
- __be16 len;
- /* 802.2 */
- u8 dsap;
- u8 ssap;
- u8 ctrl;
- /* SNAP */
- u8 oui[3];
- unsigned short ethertype;
-} __attribute__ ((packed));
-
typedef enum {
FIRMWARE_TYPE_AGERE,
FIRMWARE_TYPE_INTERSIL,
@@ -132,9 +118,6 @@
#define DEBUG(n, args...) do { } while (0)
#endif /* ORINOCO_DEBUG */
-#define TRACE_ENTER(devname) DEBUG(2, "%s: -> %s()\n", devname, __FUNCTION__);
-#define TRACE_EXIT(devname) DEBUG(2, "%s: <- %s()\n", devname, __FUNCTION__);
-
/********************************************************************/
/* Exported prototypes */
/********************************************************************/
diff --git a/drivers/net/wireless/orinoco_cs.c b/drivers/net/wireless/orinoco_cs.c
index 434f7d7..d2c48ac 100644
--- a/drivers/net/wireless/orinoco_cs.c
+++ b/drivers/net/wireless/orinoco_cs.c
@@ -178,13 +178,10 @@
int last_fn, last_ret;
u_char buf[64];
config_info_t conf;
- cisinfo_t info;
tuple_t tuple;
cisparse_t parse;
void __iomem *mem;
- CS_CHECK(ValidateCIS, pcmcia_validate_cis(link, &info));
-
/*
* This reads the card's CONFIG tuple to find its
* configuration registers.
@@ -234,12 +231,6 @@
goto next_entry;
link->conf.ConfigIndex = cfg->index;
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
- link->conf.Attributes |= CONF_ENABLE_SPKR;
- link->conf.Status = CCSR_AUDIO_ENA;
- }
-
/* Use power settings for Vcc and Vpp if present */
/* Note that the CIS values need to be rescaled */
if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
diff --git a/drivers/net/wireless/orinoco_nortel.c b/drivers/net/wireless/orinoco_nortel.c
index d1a670b..1596182 100644
--- a/drivers/net/wireless/orinoco_nortel.c
+++ b/drivers/net/wireless/orinoco_nortel.c
@@ -1,9 +1,8 @@
/* orinoco_nortel.c
- *
+ *
* Driver for Prism II devices which would usually be driven by orinoco_cs,
* but are connected to the PCI bus by a PCI-to-PCMCIA adapter used in
* Nortel emobility, Symbol LA-4113 and Symbol LA-4123.
- * but are connected to the PCI bus by a Nortel PCI-PCMCIA-Adapter.
*
* Copyright (C) 2002 Tobias Hoffmann
* (C) 2003 Christoph Jungegger <disdos@traum404.de>
@@ -50,67 +49,62 @@
#include <pcmcia/cisreg.h>
#include "orinoco.h"
+#include "orinoco_pci.h"
#define COR_OFFSET (0xe0) /* COR attribute offset of Prism2 PC card */
#define COR_VALUE (COR_LEVEL_REQ | COR_FUNC_ENA) /* Enable PC card with interrupt in level trigger */
-/* Nortel specific data */
-struct nortel_pci_card {
- unsigned long iobase1;
- unsigned long iobase2;
-};
-
/*
- * Do a soft reset of the PCI card using the Configuration Option Register
+ * Do a soft reset of the card using the Configuration Option Register
* We need this to get going...
* This is the part of the code that is strongly inspired from wlan-ng
*
* Note bis : Don't try to access HERMES_CMD during the reset phase.
* It just won't work !
*/
-static int nortel_pci_cor_reset(struct orinoco_private *priv)
+static int orinoco_nortel_cor_reset(struct orinoco_private *priv)
{
- struct nortel_pci_card *card = priv->card;
+ struct orinoco_pci_card *card = priv->card;
- /* Assert the reset until the card notice */
- outw_p(8, card->iobase1 + 2);
- inw(card->iobase2 + COR_OFFSET);
- outw_p(0x80, card->iobase2 + COR_OFFSET);
+ /* Assert the reset until the card notices */
+ iowrite16(8, card->bridge_io + 2);
+ ioread16(card->attr_io + COR_OFFSET);
+ iowrite16(0x80, card->attr_io + COR_OFFSET);
mdelay(1);
/* Give time for the card to recover from this hard effort */
- outw_p(0, card->iobase2 + COR_OFFSET);
- outw_p(0, card->iobase2 + COR_OFFSET);
+ iowrite16(0, card->attr_io + COR_OFFSET);
+ iowrite16(0, card->attr_io + COR_OFFSET);
mdelay(1);
- /* set COR as usual */
- outw_p(COR_VALUE, card->iobase2 + COR_OFFSET);
- outw_p(COR_VALUE, card->iobase2 + COR_OFFSET);
+ /* Set COR as usual */
+ iowrite16(COR_VALUE, card->attr_io + COR_OFFSET);
+ iowrite16(COR_VALUE, card->attr_io + COR_OFFSET);
mdelay(1);
- outw_p(0x228, card->iobase1 + 2);
+ iowrite16(0x228, card->bridge_io + 2);
return 0;
}
-static int nortel_pci_hw_init(struct nortel_pci_card *card)
+static int orinoco_nortel_hw_init(struct orinoco_pci_card *card)
{
int i;
u32 reg;
- /* setup bridge */
- if (inw(card->iobase1) & 1) {
+ /* Setup bridge */
+ if (ioread16(card->bridge_io) & 1) {
printk(KERN_ERR PFX "brg1 answer1 wrong\n");
return -EBUSY;
}
- outw_p(0x118, card->iobase1 + 2);
- outw_p(0x108, card->iobase1 + 2);
+ iowrite16(0x118, card->bridge_io + 2);
+ iowrite16(0x108, card->bridge_io + 2);
mdelay(30);
- outw_p(0x8, card->iobase1 + 2);
+ iowrite16(0x8, card->bridge_io + 2);
for (i = 0; i < 30; i++) {
mdelay(30);
- if (inw(card->iobase1) & 0x10) {
+ if (ioread16(card->bridge_io) & 0x10) {
break;
}
}
@@ -118,42 +112,42 @@
printk(KERN_ERR PFX "brg1 timed out\n");
return -EBUSY;
}
- if (inw(card->iobase2 + 0xe0) & 1) {
+ if (ioread16(card->attr_io + COR_OFFSET) & 1) {
printk(KERN_ERR PFX "brg2 answer1 wrong\n");
return -EBUSY;
}
- if (inw(card->iobase2 + 0xe2) & 1) {
+ if (ioread16(card->attr_io + COR_OFFSET + 2) & 1) {
printk(KERN_ERR PFX "brg2 answer2 wrong\n");
return -EBUSY;
}
- if (inw(card->iobase2 + 0xe4) & 1) {
+ if (ioread16(card->attr_io + COR_OFFSET + 4) & 1) {
printk(KERN_ERR PFX "brg2 answer3 wrong\n");
return -EBUSY;
}
- /* set the PCMCIA COR-Register */
- outw_p(COR_VALUE, card->iobase2 + COR_OFFSET);
+ /* Set the PCMCIA COR register */
+ iowrite16(COR_VALUE, card->attr_io + COR_OFFSET);
mdelay(1);
- reg = inw(card->iobase2 + COR_OFFSET);
+ reg = ioread16(card->attr_io + COR_OFFSET);
if (reg != COR_VALUE) {
printk(KERN_ERR PFX "Error setting COR value (reg=%x)\n",
reg);
return -EBUSY;
}
- /* set leds */
- outw_p(1, card->iobase1 + 10);
+ /* Set LEDs */
+ iowrite16(1, card->bridge_io + 10);
return 0;
}
-static int nortel_pci_init_one(struct pci_dev *pdev,
- const struct pci_device_id *ent)
+static int orinoco_nortel_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
{
int err;
struct orinoco_private *priv;
- struct nortel_pci_card *card;
+ struct orinoco_pci_card *card;
struct net_device *dev;
- void __iomem *iomem;
+ void __iomem *hermes_io, *bridge_io, *attr_io;
err = pci_enable_device(pdev);
if (err) {
@@ -162,19 +156,34 @@
}
err = pci_request_regions(pdev, DRIVER_NAME);
- if (err != 0) {
+ if (err) {
printk(KERN_ERR PFX "Cannot obtain PCI resources\n");
goto fail_resources;
}
- iomem = pci_iomap(pdev, 2, 0);
- if (!iomem) {
- err = -ENOMEM;
- goto fail_map_io;
+ bridge_io = pci_iomap(pdev, 0, 0);
+ if (!bridge_io) {
+ printk(KERN_ERR PFX "Cannot map bridge registers\n");
+ err = -EIO;
+ goto fail_map_bridge;
+ }
+
+ attr_io = pci_iomap(pdev, 1, 0);
+ if (!attr_io) {
+ printk(KERN_ERR PFX "Cannot map PCMCIA attributes\n");
+ err = -EIO;
+ goto fail_map_attr;
+ }
+
+ hermes_io = pci_iomap(pdev, 2, 0);
+ if (!hermes_io) {
+ printk(KERN_ERR PFX "Cannot map chipset registers\n");
+ err = -EIO;
+ goto fail_map_hermes;
}
/* Allocate network device */
- dev = alloc_orinocodev(sizeof(*card), nortel_pci_cor_reset);
+ dev = alloc_orinocodev(sizeof(*card), orinoco_nortel_cor_reset);
if (!dev) {
printk(KERN_ERR PFX "Cannot allocate network device\n");
err = -ENOMEM;
@@ -183,16 +192,12 @@
priv = netdev_priv(dev);
card = priv->card;
- card->iobase1 = pci_resource_start(pdev, 0);
- card->iobase2 = pci_resource_start(pdev, 1);
- dev->base_addr = pci_resource_start(pdev, 2);
+ card->bridge_io = bridge_io;
+ card->attr_io = attr_io;
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev);
- hermes_struct_init(&priv->hw, iomem, HERMES_16BIT_REGSPACING);
-
- printk(KERN_DEBUG PFX "Detected Nortel PCI device at %s irq:%d, "
- "io addr:0x%lx\n", pci_name(pdev), pdev->irq, dev->base_addr);
+ hermes_struct_init(&priv->hw, hermes_io, HERMES_16BIT_REGSPACING);
err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ,
dev->name, dev);
@@ -201,21 +206,20 @@
err = -EBUSY;
goto fail_irq;
}
- dev->irq = pdev->irq;
+ orinoco_pci_setup_netdev(dev, pdev, 2);
- err = nortel_pci_hw_init(card);
+ err = orinoco_nortel_hw_init(card);
if (err) {
printk(KERN_ERR PFX "Hardware initialization failed\n");
goto fail;
}
- err = nortel_pci_cor_reset(priv);
+ err = orinoco_nortel_cor_reset(priv);
if (err) {
printk(KERN_ERR PFX "Initial reset failed\n");
goto fail;
}
-
err = register_netdev(dev);
if (err) {
printk(KERN_ERR PFX "Cannot register network device\n");
@@ -234,9 +238,15 @@
free_orinocodev(dev);
fail_alloc:
- pci_iounmap(pdev, iomem);
+ pci_iounmap(pdev, hermes_io);
- fail_map_io:
+ fail_map_hermes:
+ pci_iounmap(pdev, attr_io);
+
+ fail_map_attr:
+ pci_iounmap(pdev, bridge_io);
+
+ fail_map_bridge:
pci_release_regions(pdev);
fail_resources:
@@ -245,26 +255,27 @@
return err;
}
-static void __devexit nortel_pci_remove_one(struct pci_dev *pdev)
+static void __devexit orinoco_nortel_remove_one(struct pci_dev *pdev)
{
struct net_device *dev = pci_get_drvdata(pdev);
struct orinoco_private *priv = netdev_priv(dev);
- struct nortel_pci_card *card = priv->card;
+ struct orinoco_pci_card *card = priv->card;
- /* clear leds */
- outw_p(0, card->iobase1 + 10);
+ /* Clear LEDs */
+ iowrite16(0, card->bridge_io + 10);
unregister_netdev(dev);
free_irq(dev->irq, dev);
pci_set_drvdata(pdev, NULL);
free_orinocodev(dev);
pci_iounmap(pdev, priv->hw.iobase);
+ pci_iounmap(pdev, card->attr_io);
+ pci_iounmap(pdev, card->bridge_io);
pci_release_regions(pdev);
pci_disable_device(pdev);
}
-
-static struct pci_device_id nortel_pci_id_table[] = {
+static struct pci_device_id orinoco_nortel_id_table[] = {
/* Nortel emobility PCI */
{0x126c, 0x8030, PCI_ANY_ID, PCI_ANY_ID,},
/* Symbol LA-4123 PCI */
@@ -272,13 +283,15 @@
{0,},
};
-MODULE_DEVICE_TABLE(pci, nortel_pci_id_table);
+MODULE_DEVICE_TABLE(pci, orinoco_nortel_id_table);
-static struct pci_driver nortel_pci_driver = {
- .name = DRIVER_NAME,
- .id_table = nortel_pci_id_table,
- .probe = nortel_pci_init_one,
- .remove = __devexit_p(nortel_pci_remove_one),
+static struct pci_driver orinoco_nortel_driver = {
+ .name = DRIVER_NAME,
+ .id_table = orinoco_nortel_id_table,
+ .probe = orinoco_nortel_init_one,
+ .remove = __devexit_p(orinoco_nortel_remove_one),
+ .suspend = orinoco_pci_suspend,
+ .resume = orinoco_pci_resume,
};
static char version[] __initdata = DRIVER_NAME " " DRIVER_VERSION
@@ -288,20 +301,19 @@
("Driver for wireless LAN cards using the Nortel PCI bridge");
MODULE_LICENSE("Dual MPL/GPL");
-static int __init nortel_pci_init(void)
+static int __init orinoco_nortel_init(void)
{
printk(KERN_DEBUG "%s\n", version);
- return pci_module_init(&nortel_pci_driver);
+ return pci_module_init(&orinoco_nortel_driver);
}
-static void __exit nortel_pci_exit(void)
+static void __exit orinoco_nortel_exit(void)
{
- pci_unregister_driver(&nortel_pci_driver);
- ssleep(1);
+ pci_unregister_driver(&orinoco_nortel_driver);
}
-module_init(nortel_pci_init);
-module_exit(nortel_pci_exit);
+module_init(orinoco_nortel_init);
+module_exit(orinoco_nortel_exit);
/*
* Local variables:
diff --git a/drivers/net/wireless/orinoco_pci.c b/drivers/net/wireless/orinoco_pci.c
index 5362c21..df37b95 100644
--- a/drivers/net/wireless/orinoco_pci.c
+++ b/drivers/net/wireless/orinoco_pci.c
@@ -1,11 +1,11 @@
/* orinoco_pci.c
*
- * Driver for Prism II devices that have a direct PCI interface
- * (i.e., not in a Pcmcia or PLX bridge)
+ * Driver for Prism 2.5/3 devices that have a direct PCI interface
+ * (i.e. these are not PCMCIA cards in a PCMCIA-to-PCI bridge).
+ * The card contains only one PCI region, which contains all the usual
+ * hermes registers, as well as the COR register.
*
- * Specifically here we're talking about the Linksys WMP11
- *
- * Current maintainers (as of 29 September 2003) are:
+ * Current maintainers are:
* Pavel Roskin <proski AT gnu.org>
* and David Gibson <hermes AT gibson.dropbear.id.au>
*
@@ -41,54 +41,6 @@
* under either the MPL or the GPL.
*/
-/*
- * Theory of operation...
- * -------------------
- * Maybe you had a look in orinoco_plx. Well, this is totally different...
- *
- * The card contains only one PCI region, which contains all the usual
- * hermes registers.
- *
- * The driver will memory map this region in normal memory. Because
- * the hermes registers are mapped in normal memory and not in ISA I/O
- * post space, we can't use the usual inw/outw macros and we need to
- * use readw/writew.
- * This slight difference force us to compile our own version of
- * hermes.c with the register access macro changed. That's a bit
- * hackish but works fine.
- *
- * Note that the PCI region is pretty big (4K). That's much more than
- * the usual set of hermes register (0x0 -> 0x3E). I've got a strong
- * suspicion that the whole memory space of the adapter is in fact in
- * this region. Accessing directly the adapter memory instead of going
- * through the usual register would speed up significantely the
- * operations...
- *
- * Finally, the card looks like this :
------------------------
- Bus 0, device 14, function 0:
- Network controller: PCI device 1260:3873 (Harris Semiconductor) (rev 1).
- IRQ 11.
- Master Capable. Latency=248.
- Prefetchable 32 bit memory at 0xffbcc000 [0xffbccfff].
------------------------
-00:0e.0 Network controller: Harris Semiconductor: Unknown device 3873 (rev 01)
- Subsystem: Unknown device 1737:3874
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 248 set, cache line size 08
- Interrupt: pin A routed to IRQ 11
- Region 0: Memory at ffbcc000 (32-bit, prefetchable) [size=4K]
- Capabilities: [dc] Power Management version 2
- Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME+
- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
------------------------
- *
- * That's all..
- *
- * Jean II
- */
-
#define DRIVER_NAME "orinoco_pci"
#define PFX DRIVER_NAME ": "
@@ -100,12 +52,14 @@
#include <linux/pci.h>
#include "orinoco.h"
+#include "orinoco_pci.h"
-/* All the magic there is from wlan-ng */
-/* Magic offset of the reset register of the PCI card */
+/* Offset of the COR register of the PCI card */
#define HERMES_PCI_COR (0x26)
-/* Magic bitmask to reset the card */
+
+/* Bitmask to reset the card */
#define HERMES_PCI_COR_MASK (0x0080)
+
/* Magic timeouts for doing the reset.
* Those times are straight from wlan-ng, and it is claimed that they
* are necessary. Alan will kill me. Take your time and grab a coffee. */
@@ -113,13 +67,8 @@
#define HERMES_PCI_COR_OFFT (500) /* ms */
#define HERMES_PCI_COR_BUSYT (500) /* ms */
-/* Orinoco PCI specific data */
-struct orinoco_pci_card {
- void __iomem *pci_ioaddr;
-};
-
/*
- * Do a soft reset of the PCI card using the Configuration Option Register
+ * Do a soft reset of the card using the Configuration Option Register
* We need this to get going...
* This is the part of the code that is strongly inspired from wlan-ng
*
@@ -131,14 +80,13 @@
* Note bis : Don't try to access HERMES_CMD during the reset phase.
* It just won't work !
*/
-static int
-orinoco_pci_cor_reset(struct orinoco_private *priv)
+static int orinoco_pci_cor_reset(struct orinoco_private *priv)
{
hermes_t *hw = &priv->hw;
- unsigned long timeout;
- u16 reg;
+ unsigned long timeout;
+ u16 reg;
- /* Assert the reset until the card notice */
+ /* Assert the reset until the card notices */
hermes_write_regn(hw, PCI_COR, HERMES_PCI_COR_MASK);
mdelay(HERMES_PCI_COR_ONT);
@@ -163,19 +111,14 @@
return 0;
}
-/*
- * Initialise a card. Mostly similar to PLX code.
- */
static int orinoco_pci_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
- int err = 0;
- unsigned long pci_iorange;
- u16 __iomem *pci_ioaddr = NULL;
- unsigned long pci_iolen;
- struct orinoco_private *priv = NULL;
+ int err;
+ struct orinoco_private *priv;
struct orinoco_pci_card *card;
- struct net_device *dev = NULL;
+ struct net_device *dev;
+ void __iomem *hermes_io;
err = pci_enable_device(pdev);
if (err) {
@@ -184,39 +127,32 @@
}
err = pci_request_regions(pdev, DRIVER_NAME);
- if (err != 0) {
+ if (err) {
printk(KERN_ERR PFX "Cannot obtain PCI resources\n");
goto fail_resources;
}
- /* Resource 0 is mapped to the hermes registers */
- pci_iorange = pci_resource_start(pdev, 0);
- pci_iolen = pci_resource_len(pdev, 0);
- pci_ioaddr = ioremap(pci_iorange, pci_iolen);
- if (!pci_iorange) {
- printk(KERN_ERR PFX "Cannot remap hardware registers\n");
- goto fail_map;
+ hermes_io = pci_iomap(pdev, 0, 0);
+ if (!hermes_io) {
+ printk(KERN_ERR PFX "Cannot remap chipset registers\n");
+ err = -EIO;
+ goto fail_map_hermes;
}
/* Allocate network device */
dev = alloc_orinocodev(sizeof(*card), orinoco_pci_cor_reset);
- if (! dev) {
+ if (!dev) {
+ printk(KERN_ERR PFX "Cannot allocate network device\n");
err = -ENOMEM;
goto fail_alloc;
}
priv = netdev_priv(dev);
card = priv->card;
- card->pci_ioaddr = pci_ioaddr;
- dev->mem_start = pci_iorange;
- dev->mem_end = pci_iorange + pci_iolen - 1;
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev);
- hermes_struct_init(&priv->hw, pci_ioaddr, HERMES_32BIT_REGSPACING);
-
- printk(KERN_DEBUG PFX "Detected device %s, mem:0x%lx-0x%lx, irq %d\n",
- pci_name(pdev), dev->mem_start, dev->mem_end, pdev->irq);
+ hermes_struct_init(&priv->hw, hermes_io, HERMES_32BIT_REGSPACING);
err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ,
dev->name, dev);
@@ -225,9 +161,8 @@
err = -EBUSY;
goto fail_irq;
}
- dev->irq = pdev->irq;
+ orinoco_pci_setup_netdev(dev, pdev, 0);
- /* Perform a COR reset to start the card */
err = orinoco_pci_cor_reset(priv);
if (err) {
printk(KERN_ERR PFX "Initial reset failed\n");
@@ -236,7 +171,7 @@
err = register_netdev(dev);
if (err) {
- printk(KERN_ERR PFX "Failed to register net device\n");
+ printk(KERN_ERR PFX "Cannot register network device\n");
goto fail;
}
@@ -252,9 +187,9 @@
free_orinocodev(dev);
fail_alloc:
- iounmap(pci_ioaddr);
+ pci_iounmap(pdev, hermes_io);
- fail_map:
+ fail_map_hermes:
pci_release_regions(pdev);
fail_resources:
@@ -267,87 +202,17 @@
{
struct net_device *dev = pci_get_drvdata(pdev);
struct orinoco_private *priv = netdev_priv(dev);
- struct orinoco_pci_card *card = priv->card;
unregister_netdev(dev);
free_irq(dev->irq, dev);
pci_set_drvdata(pdev, NULL);
free_orinocodev(dev);
- iounmap(card->pci_ioaddr);
+ pci_iounmap(pdev, priv->hw.iobase);
pci_release_regions(pdev);
pci_disable_device(pdev);
}
-static int orinoco_pci_suspend(struct pci_dev *pdev, pm_message_t state)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
- struct orinoco_private *priv = netdev_priv(dev);
- unsigned long flags;
- int err;
-
-
- err = orinoco_lock(priv, &flags);
- if (err) {
- printk(KERN_ERR "%s: hw_unavailable on orinoco_pci_suspend\n",
- dev->name);
- return err;
- }
-
- err = __orinoco_down(dev);
- if (err)
- printk(KERN_WARNING "%s: orinoco_pci_suspend(): Error %d downing interface\n",
- dev->name, err);
-
- netif_device_detach(dev);
-
- priv->hw_unavailable++;
-
- orinoco_unlock(priv, &flags);
-
- pci_save_state(pdev);
- pci_set_power_state(pdev, PCI_D3hot);
-
- return 0;
-}
-
-static int orinoco_pci_resume(struct pci_dev *pdev)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
- struct orinoco_private *priv = netdev_priv(dev);
- unsigned long flags;
- int err;
-
- printk(KERN_DEBUG "%s: Orinoco-PCI waking up\n", dev->name);
-
- pci_set_power_state(pdev, 0);
- pci_restore_state(pdev);
-
- err = orinoco_reinit_firmware(dev);
- if (err) {
- printk(KERN_ERR "%s: Error %d re-initializing firmware on orinoco_pci_resume()\n",
- dev->name, err);
- return err;
- }
-
- spin_lock_irqsave(&priv->lock, flags);
-
- netif_device_attach(dev);
-
- priv->hw_unavailable--;
-
- if (priv->open && (! priv->hw_unavailable)) {
- err = __orinoco_up(dev);
- if (err)
- printk(KERN_ERR "%s: Error %d restarting card on orinoco_pci_resume()\n",
- dev->name, err);
- }
-
- spin_unlock_irqrestore(&priv->lock, flags);
-
- return 0;
-}
-
-static struct pci_device_id orinoco_pci_pci_id_table[] = {
+static struct pci_device_id orinoco_pci_id_table[] = {
/* Intersil Prism 3 */
{0x1260, 0x3872, PCI_ANY_ID, PCI_ANY_ID,},
/* Intersil Prism 2.5 */
@@ -357,11 +222,11 @@
{0,},
};
-MODULE_DEVICE_TABLE(pci, orinoco_pci_pci_id_table);
+MODULE_DEVICE_TABLE(pci, orinoco_pci_id_table);
static struct pci_driver orinoco_pci_driver = {
.name = DRIVER_NAME,
- .id_table = orinoco_pci_pci_id_table,
+ .id_table = orinoco_pci_id_table,
.probe = orinoco_pci_init_one,
.remove = __devexit_p(orinoco_pci_remove_one),
.suspend = orinoco_pci_suspend,
diff --git a/drivers/net/wireless/orinoco_pci.h b/drivers/net/wireless/orinoco_pci.h
new file mode 100644
index 0000000..b05a9a5
--- /dev/null
+++ b/drivers/net/wireless/orinoco_pci.h
@@ -0,0 +1,125 @@
+/* orinoco_pci.h
+ *
+ * Common code for all Orinoco drivers for PCI devices, including
+ * both native PCI and PCMCIA-to-PCI bridges.
+ *
+ * Copyright (C) 2005, Pavel Roskin.
+ * See orinoco.c for license.
+ */
+
+#ifndef _ORINOCO_PCI_H
+#define _ORINOCO_PCI_H
+
+#include <linux/netdevice.h>
+
+/* Driver specific data */
+struct orinoco_pci_card {
+ void __iomem *bridge_io;
+ void __iomem *attr_io;
+};
+
+/* Set base address or memory range of the network device based on
+ * the PCI device it's using. Specify BAR of the "main" resource.
+ * To be used after request_irq(). */
+static inline void orinoco_pci_setup_netdev(struct net_device *dev,
+ struct pci_dev *pdev, int bar)
+{
+ char *range_type;
+ unsigned long start = pci_resource_start(pdev, bar);
+ unsigned long len = pci_resource_len(pdev, bar);
+ unsigned long flags = pci_resource_flags(pdev, bar);
+ unsigned long end = start + len - 1;
+
+ dev->irq = pdev->irq;
+ if (flags & IORESOURCE_IO) {
+ dev->base_addr = start;
+ range_type = "ports";
+ } else {
+ dev->mem_start = start;
+ dev->mem_end = end;
+ range_type = "memory";
+ }
+
+ printk(KERN_DEBUG PFX "%s: irq %d, %s 0x%lx-0x%lx\n",
+ pci_name(pdev), pdev->irq, range_type, start, end);
+}
+
+static int orinoco_pci_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ struct net_device *dev = pci_get_drvdata(pdev);
+ struct orinoco_private *priv = netdev_priv(dev);
+ unsigned long flags;
+ int err;
+
+ err = orinoco_lock(priv, &flags);
+ if (err) {
+ printk(KERN_ERR "%s: cannot lock hardware for suspend\n",
+ dev->name);
+ return err;
+ }
+
+ err = __orinoco_down(dev);
+ if (err)
+ printk(KERN_WARNING "%s: error %d bringing interface down "
+ "for suspend\n", dev->name, err);
+
+ netif_device_detach(dev);
+
+ priv->hw_unavailable++;
+
+ orinoco_unlock(priv, &flags);
+
+ free_irq(pdev->irq, dev);
+ pci_save_state(pdev);
+ pci_disable_device(pdev);
+ pci_set_power_state(pdev, PCI_D3hot);
+
+ return 0;
+}
+
+static int orinoco_pci_resume(struct pci_dev *pdev)
+{
+ struct net_device *dev = pci_get_drvdata(pdev);
+ struct orinoco_private *priv = netdev_priv(dev);
+ unsigned long flags;
+ int err;
+
+ pci_set_power_state(pdev, 0);
+ pci_enable_device(pdev);
+ pci_restore_state(pdev);
+
+ err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ,
+ dev->name, dev);
+ if (err) {
+ printk(KERN_ERR "%s: cannot re-allocate IRQ on resume\n",
+ dev->name);
+ pci_disable_device(pdev);
+ return -EBUSY;
+ }
+
+ err = orinoco_reinit_firmware(dev);
+ if (err) {
+ printk(KERN_ERR "%s: error %d re-initializing firmware "
+ "on resume\n", dev->name, err);
+ return err;
+ }
+
+ spin_lock_irqsave(&priv->lock, flags);
+
+ netif_device_attach(dev);
+
+ priv->hw_unavailable--;
+
+ if (priv->open && (! priv->hw_unavailable)) {
+ err = __orinoco_up(dev);
+ if (err)
+ printk(KERN_ERR "%s: Error %d restarting card on resume\n",
+ dev->name, err);
+ }
+
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ return 0;
+}
+
+#endif /* _ORINOCO_PCI_H */
diff --git a/drivers/net/wireless/orinoco_plx.c b/drivers/net/wireless/orinoco_plx.c
index 210e737..7b94050 100644
--- a/drivers/net/wireless/orinoco_plx.c
+++ b/drivers/net/wireless/orinoco_plx.c
@@ -3,7 +3,7 @@
* Driver for Prism II devices which would usually be driven by orinoco_cs,
* but are connected to the PCI bus by a PLX9052.
*
- * Current maintainers (as of 29 September 2003) are:
+ * Current maintainers are:
* Pavel Roskin <proski AT gnu.org>
* and David Gibson <hermes AT gibson.dropbear.id.au>
*
@@ -30,38 +30,18 @@
* other provisions required by the GPL. If you do not delete the
* provisions above, a recipient may use your version of this file
* under either the MPL or the GPL.
-
- * Caution: this is experimental and probably buggy. For success and
- * failure reports for different cards and adaptors, see
- * orinoco_plx_pci_id_table near the end of the file. If you have a
- * card we don't have the PCI id for, and looks like it should work,
- * drop me mail with the id and "it works"/"it doesn't work".
*
- * Note: if everything gets detected fine but it doesn't actually send
- * or receive packets, your first port of call should probably be to
- * try newer firmware in the card. Especially if you're doing Ad-Hoc
- * modes.
- *
- * The actual driving is done by orinoco.c, this is just resource
- * allocation stuff. The explanation below is courtesy of Ryan Niemi
- * on the linux-wlan-ng list at
- * http://archives.neohapsis.com/archives/dev/linux-wlan/2001-q1/0026.html
- *
- * The PLX9052-based cards (WL11000 and several others) are a
- * different beast than the usual PCMCIA-based PRISM2 configuration
- * expected by wlan-ng. Here's the general details on how the WL11000
- * PCI adapter works:
+ * Here's the general details on how the PLX9052 adapter works:
*
* - Two PCI I/O address spaces, one 0x80 long which contains the
* PLX9052 registers, and one that's 0x40 long mapped to the PCMCIA
* slot I/O address space.
*
- * - One PCI memory address space, mapped to the PCMCIA memory space
+ * - One PCI memory address space, mapped to the PCMCIA attribute space
* (containing the CIS).
*
- * After identifying the I/O and memory space, you can read through
- * the memory space to confirm the CIS's device ID or manufacturer ID
- * to make sure it's the expected card. qKeep in mind that the PCMCIA
+ * Using the later, you can read through the CIS data to make sure the
+ * card is compatible with the driver. Keep in mind that the PCMCIA
* spec specifies the CIS as the lower 8 bits of each word read from
* the CIS, so to read the bytes of the CIS, read every other byte
* (0,2,4,...). Passing that test, you need to enable the I/O address
@@ -71,7 +51,7 @@
* within the PCI memory space. Write 0x41 to the COR register to
* enable I/O mode and to select level triggered interrupts. To
* confirm you actually succeeded, read the COR register back and make
- * sure it actually got set to 0x41, incase you have an unexpected
+ * sure it actually got set to 0x41, in case you have an unexpected
* card inserted.
*
* Following that, you can treat the second PCI I/O address space (the
@@ -101,16 +81,6 @@
* that, I've hot-swapped a number of times during debugging and
* driver development for various reasons (stuck WAIT# line after the
* radio card's firmware locks up).
- *
- * Hope this is enough info for someone to add PLX9052 support to the
- * wlan-ng card. In the case of the WL11000, the PCI ID's are
- * 0x1639/0x0200, with matching subsystem ID's. Other PLX9052-based
- * manufacturers other than Eumitcom (or on cards other than the
- * WL11000) may have different PCI ID's.
- *
- * If anyone needs any more specific info, let me know. I haven't had
- * time to implement support myself yet, and with the way things are
- * going, might not have time for a while..
*/
#define DRIVER_NAME "orinoco_plx"
@@ -125,6 +95,7 @@
#include <pcmcia/cisreg.h>
#include "orinoco.h"
+#include "orinoco_pci.h"
#define COR_OFFSET (0x3e0) /* COR attribute offset of Prism2 PC card */
#define COR_VALUE (COR_LEVEL_REQ | COR_FUNC_ENA) /* Enable PC card with interrupt in level trigger */
@@ -134,30 +105,20 @@
#define PLX_INTCSR 0x4c /* Interrupt Control & Status Register */
#define PLX_INTCSR_INTEN (1<<6) /* Interrupt Enable bit */
-static const u8 cis_magic[] = {
- 0x01, 0x03, 0x00, 0x00, 0xff, 0x17, 0x04, 0x67
-};
-
-/* Orinoco PLX specific data */
-struct orinoco_plx_card {
- void __iomem *attr_mem;
-};
-
/*
* Do a soft reset of the card using the Configuration Option Register
*/
static int orinoco_plx_cor_reset(struct orinoco_private *priv)
{
hermes_t *hw = &priv->hw;
- struct orinoco_plx_card *card = priv->card;
- u8 __iomem *attr_mem = card->attr_mem;
+ struct orinoco_pci_card *card = priv->card;
unsigned long timeout;
u16 reg;
- writeb(COR_VALUE | COR_RESET, attr_mem + COR_OFFSET);
+ iowrite8(COR_VALUE | COR_RESET, card->attr_io + COR_OFFSET);
mdelay(1);
- writeb(COR_VALUE, attr_mem + COR_OFFSET);
+ iowrite8(COR_VALUE, card->attr_io + COR_OFFSET);
mdelay(1);
/* Just in case, wait more until the card is no longer busy */
@@ -168,7 +129,7 @@
reg = hermes_read_regn(hw, CMD);
}
- /* Did we timeout ? */
+ /* Still busy? */
if (reg & HERMES_CMD_BUSY) {
printk(KERN_ERR PFX "Busy timeout\n");
return -ETIMEDOUT;
@@ -177,20 +138,55 @@
return 0;
}
+static int orinoco_plx_hw_init(struct orinoco_pci_card *card)
+{
+ int i;
+ u32 csr_reg;
+ static const u8 cis_magic[] = {
+ 0x01, 0x03, 0x00, 0x00, 0xff, 0x17, 0x04, 0x67
+ };
+
+ printk(KERN_DEBUG PFX "CIS: ");
+ for (i = 0; i < 16; i++) {
+ printk("%02X:", ioread8(card->attr_io + (i << 1)));
+ }
+ printk("\n");
+
+ /* Verify whether a supported PC card is present */
+ /* FIXME: we probably need to be smarted about this */
+ for (i = 0; i < sizeof(cis_magic); i++) {
+ if (cis_magic[i] != ioread8(card->attr_io + (i << 1))) {
+ printk(KERN_ERR PFX "The CIS value of Prism2 PC "
+ "card is unexpected\n");
+ return -ENODEV;
+ }
+ }
+
+ /* bjoern: We need to tell the card to enable interrupts, in
+ case the serial eprom didn't do this already. See the
+ PLX9052 data book, p8-1 and 8-24 for reference. */
+ csr_reg = ioread32(card->bridge_io + PLX_INTCSR);
+ if (!(csr_reg & PLX_INTCSR_INTEN)) {
+ csr_reg |= PLX_INTCSR_INTEN;
+ iowrite32(csr_reg, card->bridge_io + PLX_INTCSR);
+ csr_reg = ioread32(card->bridge_io + PLX_INTCSR);
+ if (!(csr_reg & PLX_INTCSR_INTEN)) {
+ printk(KERN_ERR PFX "Cannot enable interrupts\n");
+ return -EIO;
+ }
+ }
+
+ return 0;
+}
static int orinoco_plx_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
- int err = 0;
- u8 __iomem *attr_mem = NULL;
- u32 csr_reg, plx_addr;
- struct orinoco_private *priv = NULL;
- struct orinoco_plx_card *card;
- unsigned long pccard_ioaddr = 0;
- unsigned long pccard_iolen = 0;
- struct net_device *dev = NULL;
- void __iomem *mem;
- int i;
+ int err;
+ struct orinoco_private *priv;
+ struct orinoco_pci_card *card;
+ struct net_device *dev;
+ void __iomem *hermes_io, *attr_io, *bridge_io;
err = pci_enable_device(pdev);
if (err) {
@@ -199,30 +195,30 @@
}
err = pci_request_regions(pdev, DRIVER_NAME);
- if (err != 0) {
+ if (err) {
printk(KERN_ERR PFX "Cannot obtain PCI resources\n");
goto fail_resources;
}
- /* Resource 1 is mapped to PLX-specific registers */
- plx_addr = pci_resource_start(pdev, 1);
+ bridge_io = pci_iomap(pdev, 1, 0);
+ if (!bridge_io) {
+ printk(KERN_ERR PFX "Cannot map bridge registers\n");
+ err = -EIO;
+ goto fail_map_bridge;
+ }
- /* Resource 2 is mapped to the PCMCIA attribute memory */
- attr_mem = ioremap(pci_resource_start(pdev, 2),
- pci_resource_len(pdev, 2));
- if (!attr_mem) {
- printk(KERN_ERR PFX "Cannot remap PCMCIA space\n");
+ attr_io = pci_iomap(pdev, 2, 0);
+ if (!attr_io) {
+ printk(KERN_ERR PFX "Cannot map PCMCIA attributes\n");
+ err = -EIO;
goto fail_map_attr;
}
- /* Resource 3 is mapped to the PCMCIA I/O address space */
- pccard_ioaddr = pci_resource_start(pdev, 3);
- pccard_iolen = pci_resource_len(pdev, 3);
-
- mem = pci_iomap(pdev, 3, 0);
- if (!mem) {
- err = -ENOMEM;
- goto fail_map_io;
+ hermes_io = pci_iomap(pdev, 3, 0);
+ if (!hermes_io) {
+ printk(KERN_ERR PFX "Cannot map chipset registers\n");
+ err = -EIO;
+ goto fail_map_hermes;
}
/* Allocate network device */
@@ -235,16 +231,12 @@
priv = netdev_priv(dev);
card = priv->card;
- card->attr_mem = attr_mem;
- dev->base_addr = pccard_ioaddr;
+ card->bridge_io = bridge_io;
+ card->attr_io = attr_io;
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev);
- hermes_struct_init(&priv->hw, mem, HERMES_16BIT_REGSPACING);
-
- printk(KERN_DEBUG PFX "Detected Orinoco/Prism2 PLX device "
- "at %s irq:%d, io addr:0x%lx\n", pci_name(pdev), pdev->irq,
- pccard_ioaddr);
+ hermes_struct_init(&priv->hw, hermes_io, HERMES_16BIT_REGSPACING);
err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ,
dev->name, dev);
@@ -253,20 +245,12 @@
err = -EBUSY;
goto fail_irq;
}
- dev->irq = pdev->irq;
+ orinoco_pci_setup_netdev(dev, pdev, 2);
- /* bjoern: We need to tell the card to enable interrupts, in
- case the serial eprom didn't do this already. See the
- PLX9052 data book, p8-1 and 8-24 for reference. */
- csr_reg = inl(plx_addr + PLX_INTCSR);
- if (!(csr_reg & PLX_INTCSR_INTEN)) {
- csr_reg |= PLX_INTCSR_INTEN;
- outl(csr_reg, plx_addr + PLX_INTCSR);
- csr_reg = inl(plx_addr + PLX_INTCSR);
- if (!(csr_reg & PLX_INTCSR_INTEN)) {
- printk(KERN_ERR PFX "Cannot enable interrupts\n");
- goto fail;
- }
+ err = orinoco_plx_hw_init(card);
+ if (err) {
+ printk(KERN_ERR PFX "Hardware initialization failed\n");
+ goto fail;
}
err = orinoco_plx_cor_reset(priv);
@@ -275,23 +259,6 @@
goto fail;
}
- printk(KERN_DEBUG PFX "CIS: ");
- for (i = 0; i < 16; i++) {
- printk("%02X:", readb(attr_mem + 2*i));
- }
- printk("\n");
-
- /* Verify whether a supported PC card is present */
- /* FIXME: we probably need to be smarted about this */
- for (i = 0; i < sizeof(cis_magic); i++) {
- if (cis_magic[i] != readb(attr_mem +2*i)) {
- printk(KERN_ERR PFX "The CIS value of Prism2 PC "
- "card is unexpected\n");
- err = -EIO;
- goto fail;
- }
- }
-
err = register_netdev(dev);
if (err) {
printk(KERN_ERR PFX "Cannot register network device\n");
@@ -310,12 +277,15 @@
free_orinocodev(dev);
fail_alloc:
- pci_iounmap(pdev, mem);
+ pci_iounmap(pdev, hermes_io);
- fail_map_io:
- iounmap(attr_mem);
+ fail_map_hermes:
+ pci_iounmap(pdev, attr_io);
fail_map_attr:
+ pci_iounmap(pdev, bridge_io);
+
+ fail_map_bridge:
pci_release_regions(pdev);
fail_resources:
@@ -328,23 +298,20 @@
{
struct net_device *dev = pci_get_drvdata(pdev);
struct orinoco_private *priv = netdev_priv(dev);
- struct orinoco_plx_card *card = priv->card;
- u8 __iomem *attr_mem = card->attr_mem;
-
- BUG_ON(! dev);
+ struct orinoco_pci_card *card = priv->card;
unregister_netdev(dev);
free_irq(dev->irq, dev);
pci_set_drvdata(pdev, NULL);
free_orinocodev(dev);
pci_iounmap(pdev, priv->hw.iobase);
- iounmap(attr_mem);
+ pci_iounmap(pdev, card->attr_io);
+ pci_iounmap(pdev, card->bridge_io);
pci_release_regions(pdev);
pci_disable_device(pdev);
}
-
-static struct pci_device_id orinoco_plx_pci_id_table[] = {
+static struct pci_device_id orinoco_plx_id_table[] = {
{0x111a, 0x1023, PCI_ANY_ID, PCI_ANY_ID,}, /* Siemens SpeedStream SS1023 */
{0x1385, 0x4100, PCI_ANY_ID, PCI_ANY_ID,}, /* Netgear MA301 */
{0x15e8, 0x0130, PCI_ANY_ID, PCI_ANY_ID,}, /* Correga - does this work? */
@@ -362,13 +329,15 @@
{0,},
};
-MODULE_DEVICE_TABLE(pci, orinoco_plx_pci_id_table);
+MODULE_DEVICE_TABLE(pci, orinoco_plx_id_table);
static struct pci_driver orinoco_plx_driver = {
.name = DRIVER_NAME,
- .id_table = orinoco_plx_pci_id_table,
+ .id_table = orinoco_plx_id_table,
.probe = orinoco_plx_init_one,
.remove = __devexit_p(orinoco_plx_remove_one),
+ .suspend = orinoco_pci_suspend,
+ .resume = orinoco_pci_resume,
};
static char version[] __initdata = DRIVER_NAME " " DRIVER_VERSION
@@ -388,7 +357,6 @@
static void __exit orinoco_plx_exit(void)
{
pci_unregister_driver(&orinoco_plx_driver);
- ssleep(1);
}
module_init(orinoco_plx_init);
diff --git a/drivers/net/wireless/orinoco_tmd.c b/drivers/net/wireless/orinoco_tmd.c
index 5e68b70..0496663 100644
--- a/drivers/net/wireless/orinoco_tmd.c
+++ b/drivers/net/wireless/orinoco_tmd.c
@@ -1,5 +1,5 @@
/* orinoco_tmd.c
- *
+ *
* Driver for Prism II devices which would usually be driven by orinoco_cs,
* but are connected to the PCI bus by a TMD7160.
*
@@ -26,25 +26,13 @@
* other provisions required by the GPL. If you do not delete the
* provisions above, a recipient may use your version of this file
* under either the MPL or the GPL.
-
- * Caution: this is experimental and probably buggy. For success and
- * failure reports for different cards and adaptors, see
- * orinoco_tmd_pci_id_table near the end of the file. If you have a
- * card we don't have the PCI id for, and looks like it should work,
- * drop me mail with the id and "it works"/"it doesn't work".
- *
- * Note: if everything gets detected fine but it doesn't actually send
- * or receive packets, your first port of call should probably be to
- * try newer firmware in the card. Especially if you're doing Ad-Hoc
- * modes
*
* The actual driving is done by orinoco.c, this is just resource
* allocation stuff.
*
* This driver is modeled after the orinoco_plx driver. The main
- * difference is that the TMD chip has only IO port ranges and no
- * memory space, i.e. no access to the CIS. Compared to the PLX chip,
- * the io range functionalities are exchanged.
+ * difference is that the TMD chip has only IO port ranges and doesn't
+ * provide access to the PCMCIA attribute space.
*
* Pheecom sells cards with the TMD chip as "ASIC version"
*/
@@ -61,32 +49,26 @@
#include <pcmcia/cisreg.h>
#include "orinoco.h"
+#include "orinoco_pci.h"
#define COR_VALUE (COR_LEVEL_REQ | COR_FUNC_ENA) /* Enable PC card with interrupt in level trigger */
#define COR_RESET (0x80) /* reset bit in the COR register */
#define TMD_RESET_TIME (500) /* milliseconds */
-/* Orinoco TMD specific data */
-struct orinoco_tmd_card {
- u32 tmd_io;
-};
-
-
/*
* Do a soft reset of the card using the Configuration Option Register
*/
static int orinoco_tmd_cor_reset(struct orinoco_private *priv)
{
hermes_t *hw = &priv->hw;
- struct orinoco_tmd_card *card = priv->card;
- u32 addr = card->tmd_io;
+ struct orinoco_pci_card *card = priv->card;
unsigned long timeout;
u16 reg;
- outb(COR_VALUE | COR_RESET, addr);
+ iowrite8(COR_VALUE | COR_RESET, card->bridge_io);
mdelay(1);
- outb(COR_VALUE, addr);
+ iowrite8(COR_VALUE, card->bridge_io);
mdelay(1);
/* Just in case, wait more until the card is no longer busy */
@@ -97,7 +79,7 @@
reg = hermes_read_regn(hw, CMD);
}
- /* Did we timeout ? */
+ /* Still busy? */
if (reg & HERMES_CMD_BUSY) {
printk(KERN_ERR PFX "Busy timeout\n");
return -ETIMEDOUT;
@@ -110,11 +92,11 @@
static int orinoco_tmd_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
- int err = 0;
- struct orinoco_private *priv = NULL;
- struct orinoco_tmd_card *card;
- struct net_device *dev = NULL;
- void __iomem *mem;
+ int err;
+ struct orinoco_private *priv;
+ struct orinoco_pci_card *card;
+ struct net_device *dev;
+ void __iomem *hermes_io, *bridge_io;
err = pci_enable_device(pdev);
if (err) {
@@ -123,20 +105,28 @@
}
err = pci_request_regions(pdev, DRIVER_NAME);
- if (err != 0) {
+ if (err) {
printk(KERN_ERR PFX "Cannot obtain PCI resources\n");
goto fail_resources;
}
- mem = pci_iomap(pdev, 2, 0);
- if (! mem) {
- err = -ENOMEM;
- goto fail_iomap;
+ bridge_io = pci_iomap(pdev, 1, 0);
+ if (!bridge_io) {
+ printk(KERN_ERR PFX "Cannot map bridge registers\n");
+ err = -EIO;
+ goto fail_map_bridge;
+ }
+
+ hermes_io = pci_iomap(pdev, 2, 0);
+ if (!hermes_io) {
+ printk(KERN_ERR PFX "Cannot map chipset registers\n");
+ err = -EIO;
+ goto fail_map_hermes;
}
/* Allocate network device */
dev = alloc_orinocodev(sizeof(*card), orinoco_tmd_cor_reset);
- if (! dev) {
+ if (!dev) {
printk(KERN_ERR PFX "Cannot allocate network device\n");
err = -ENOMEM;
goto fail_alloc;
@@ -144,16 +134,11 @@
priv = netdev_priv(dev);
card = priv->card;
- card->tmd_io = pci_resource_start(pdev, 1);
- dev->base_addr = pci_resource_start(pdev, 2);
+ card->bridge_io = bridge_io;
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev);
- hermes_struct_init(&priv->hw, mem, HERMES_16BIT_REGSPACING);
-
- printk(KERN_DEBUG PFX "Detected Orinoco/Prism2 TMD device "
- "at %s irq:%d, io addr:0x%lx\n", pci_name(pdev), pdev->irq,
- dev->base_addr);
+ hermes_struct_init(&priv->hw, hermes_io, HERMES_16BIT_REGSPACING);
err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ,
dev->name, dev);
@@ -162,7 +147,7 @@
err = -EBUSY;
goto fail_irq;
}
- dev->irq = pdev->irq;
+ orinoco_pci_setup_netdev(dev, pdev, 2);
err = orinoco_tmd_cor_reset(priv);
if (err) {
@@ -188,9 +173,12 @@
free_orinocodev(dev);
fail_alloc:
- pci_iounmap(pdev, mem);
+ pci_iounmap(pdev, hermes_io);
- fail_iomap:
+ fail_map_hermes:
+ pci_iounmap(pdev, bridge_io);
+
+ fail_map_bridge:
pci_release_regions(pdev);
fail_resources:
@@ -203,31 +191,32 @@
{
struct net_device *dev = pci_get_drvdata(pdev);
struct orinoco_private *priv = dev->priv;
-
- BUG_ON(! dev);
+ struct orinoco_pci_card *card = priv->card;
unregister_netdev(dev);
free_irq(dev->irq, dev);
pci_set_drvdata(pdev, NULL);
free_orinocodev(dev);
pci_iounmap(pdev, priv->hw.iobase);
+ pci_iounmap(pdev, card->bridge_io);
pci_release_regions(pdev);
pci_disable_device(pdev);
}
-
-static struct pci_device_id orinoco_tmd_pci_id_table[] = {
+static struct pci_device_id orinoco_tmd_id_table[] = {
{0x15e8, 0x0131, PCI_ANY_ID, PCI_ANY_ID,}, /* NDC and OEMs, e.g. pheecom */
{0,},
};
-MODULE_DEVICE_TABLE(pci, orinoco_tmd_pci_id_table);
+MODULE_DEVICE_TABLE(pci, orinoco_tmd_id_table);
static struct pci_driver orinoco_tmd_driver = {
.name = DRIVER_NAME,
- .id_table = orinoco_tmd_pci_id_table,
+ .id_table = orinoco_tmd_id_table,
.probe = orinoco_tmd_init_one,
.remove = __devexit_p(orinoco_tmd_remove_one),
+ .suspend = orinoco_pci_suspend,
+ .resume = orinoco_pci_resume,
};
static char version[] __initdata = DRIVER_NAME " " DRIVER_VERSION
@@ -245,7 +234,6 @@
static void __exit orinoco_tmd_exit(void)
{
pci_unregister_driver(&orinoco_tmd_driver);
- ssleep(1);
}
module_init(orinoco_tmd_init);
diff --git a/drivers/net/wireless/spectrum_cs.c b/drivers/net/wireless/spectrum_cs.c
index f7b77ce..aeb38d9 100644
--- a/drivers/net/wireless/spectrum_cs.c
+++ b/drivers/net/wireless/spectrum_cs.c
@@ -1,6 +1,6 @@
/*
* Driver for 802.11b cards using RAM-loadable Symbol firmware, such as
- * Symbol Wireless Networker LA4100, CompactFlash cards by Socket
+ * Symbol Wireless Networker LA4137, CompactFlash cards by Socket
* Communications and Intel PRO/Wireless 2011B.
*
* The driver implements Symbol firmware download. The rest is handled
@@ -120,8 +120,8 @@
* Each block has the following structure.
*/
struct dblock {
- __le32 _addr; /* adapter address where to write the block */
- __le16 _len; /* length of the data only, in bytes */
+ __le32 addr; /* adapter address where to write the block */
+ __le16 len; /* length of the data only, in bytes */
char data[0]; /* data to be written */
} __attribute__ ((packed));
@@ -131,9 +131,9 @@
* items with matching ID should be written.
*/
struct pdr {
- __le32 _id; /* record ID */
- __le32 _addr; /* adapter address where to write the data */
- __le32 _len; /* expected length of the data, in bytes */
+ __le32 id; /* record ID */
+ __le32 addr; /* adapter address where to write the data */
+ __le32 len; /* expected length of the data, in bytes */
char next[0]; /* next PDR starts here */
} __attribute__ ((packed));
@@ -144,8 +144,8 @@
* be plugged into the secondary firmware.
*/
struct pdi {
- __le16 _len; /* length of ID and data, in words */
- __le16 _id; /* record ID */
+ __le16 len; /* length of ID and data, in words */
+ __le16 id; /* record ID */
char data[0]; /* plug data */
} __attribute__ ((packed));
@@ -154,44 +154,44 @@
static inline u32
dblock_addr(const struct dblock *blk)
{
- return le32_to_cpu(blk->_addr);
+ return le32_to_cpu(blk->addr);
}
static inline u32
dblock_len(const struct dblock *blk)
{
- return le16_to_cpu(blk->_len);
+ return le16_to_cpu(blk->len);
}
static inline u32
pdr_id(const struct pdr *pdr)
{
- return le32_to_cpu(pdr->_id);
+ return le32_to_cpu(pdr->id);
}
static inline u32
pdr_addr(const struct pdr *pdr)
{
- return le32_to_cpu(pdr->_addr);
+ return le32_to_cpu(pdr->addr);
}
static inline u32
pdr_len(const struct pdr *pdr)
{
- return le32_to_cpu(pdr->_len);
+ return le32_to_cpu(pdr->len);
}
static inline u32
pdi_id(const struct pdi *pdi)
{
- return le16_to_cpu(pdi->_id);
+ return le16_to_cpu(pdi->id);
}
/* Return length of the data only, in bytes */
static inline u32
pdi_len(const struct pdi *pdi)
{
- return 2 * (le16_to_cpu(pdi->_len) - 1);
+ return 2 * (le16_to_cpu(pdi->len) - 1);
}
@@ -343,8 +343,7 @@
/* do the actual plugging */
spectrum_aux_setaddr(hw, pdr_addr(pdr));
- hermes_write_words(hw, HERMES_AUXDATA, pdi->data,
- pdi_len(pdi) / 2);
+ hermes_write_bytes(hw, HERMES_AUXDATA, pdi->data, pdi_len(pdi));
return 0;
}
@@ -424,8 +423,8 @@
while (dblock_addr(blk) != BLOCK_END) {
spectrum_aux_setaddr(hw, blkaddr);
- hermes_write_words(hw, HERMES_AUXDATA, blk->data,
- blklen / 2);
+ hermes_write_bytes(hw, HERMES_AUXDATA, blk->data,
+ blklen);
blk = (struct dblock *) &blk->data[blklen];
blkaddr = dblock_addr(blk);
@@ -653,13 +652,10 @@
int last_fn, last_ret;
u_char buf[64];
config_info_t conf;
- cisinfo_t info;
tuple_t tuple;
cisparse_t parse;
void __iomem *mem;
- CS_CHECK(ValidateCIS, pcmcia_validate_cis(link, &info));
-
/*
* This reads the card's CONFIG tuple to find its
* configuration registers.
@@ -709,12 +705,6 @@
goto next_entry;
link->conf.ConfigIndex = cfg->index;
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
- link->conf.Attributes |= CONF_ENABLE_SPKR;
- link->conf.Status = CCSR_AUDIO_ENA;
- }
-
/* Use power settings for Vcc and Vpp if present */
/* Note that the CIS values need to be rescaled */
if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
@@ -932,7 +922,7 @@
" David Gibson <hermes@gibson.dropbear.id.au>, et al)";
static struct pcmcia_device_id spectrum_cs_ids[] = {
- PCMCIA_DEVICE_MANF_CARD(0x026c, 0x0001), /* Symbol Spectrum24 LA4100 */
+ PCMCIA_DEVICE_MANF_CARD(0x026c, 0x0001), /* Symbol Spectrum24 LA4137 */
PCMCIA_DEVICE_MANF_CARD(0x0104, 0x0001), /* Socket Communications CF */
PCMCIA_DEVICE_PROD_ID12("Intel", "PRO/Wireless LAN PC Card", 0x816cc815, 0x6fbf459a), /* 2011B, not 2011 */
PCMCIA_DEVICE_NULL,
diff --git a/include/net/ieee80211.h b/include/net/ieee80211.h
index 4725ff8..4087dfc 100644
--- a/include/net/ieee80211.h
+++ b/include/net/ieee80211.h
@@ -29,7 +29,7 @@
#include <linux/kernel.h> /* ARRAY_SIZE */
#include <linux/wireless.h>
-#define IEEE80211_VERSION "git-1.1.7"
+#define IEEE80211_VERSION "git-1.1.13"
#define IEEE80211_DATA_LEN 2304
/* Maximum size for the MA-UNITDATA primitive, 802.11 standard section
@@ -104,6 +104,9 @@
#define IEEE80211_SCTL_FRAG 0x000F
#define IEEE80211_SCTL_SEQ 0xFFF0
+/* QOS control */
+#define IEEE80211_QCTL_TID 0x000F
+
/* debug macros */
#ifdef CONFIG_IEEE80211_DEBUG
@@ -1073,6 +1076,7 @@
int (*handle_management) (struct net_device * dev,
struct ieee80211_network * network, u16 type);
+ int (*is_qos_active) (struct net_device *dev, struct sk_buff *skb);
/* Typical STA methods */
int (*handle_auth) (struct net_device * dev,
diff --git a/include/net/ieee80211softmac_wx.h b/include/net/ieee80211softmac_wx.h
index 3e0be45..4ee3ad5 100644
--- a/include/net/ieee80211softmac_wx.h
+++ b/include/net/ieee80211softmac_wx.h
@@ -91,4 +91,9 @@
struct iw_request_info *info,
union iwreq_data *wrqu,
char *extra);
+extern int
+ieee80211softmac_wx_set_mlme(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra);
#endif /* _IEEE80211SOFTMAC_WX */
diff --git a/net/ieee80211/ieee80211_crypt_tkip.c b/net/ieee80211/ieee80211_crypt_tkip.c
index 93def94..3fa5df2 100644
--- a/net/ieee80211/ieee80211_crypt_tkip.c
+++ b/net/ieee80211/ieee80211_crypt_tkip.c
@@ -501,8 +501,11 @@
static void michael_mic_hdr(struct sk_buff *skb, u8 * hdr)
{
struct ieee80211_hdr_4addr *hdr11;
+ u16 stype;
hdr11 = (struct ieee80211_hdr_4addr *)skb->data;
+ stype = WLAN_FC_GET_STYPE(le16_to_cpu(hdr11->frame_ctl));
+
switch (le16_to_cpu(hdr11->frame_ctl) &
(IEEE80211_FCTL_FROMDS | IEEE80211_FCTL_TODS)) {
case IEEE80211_FCTL_TODS:
@@ -523,7 +526,13 @@
break;
}
- hdr[12] = 0; /* priority */
+ if (stype & IEEE80211_STYPE_QOS_DATA) {
+ const struct ieee80211_hdr_3addrqos *qoshdr =
+ (struct ieee80211_hdr_3addrqos *)skb->data;
+ hdr[12] = le16_to_cpu(qoshdr->qos_ctl) & IEEE80211_QCTL_TID;
+ } else
+ hdr[12] = 0; /* priority */
+
hdr[13] = hdr[14] = hdr[15] = 0; /* reserved */
}
diff --git a/net/ieee80211/ieee80211_rx.c b/net/ieee80211/ieee80211_rx.c
index 604b7b0..2bf567f 100644
--- a/net/ieee80211/ieee80211_rx.c
+++ b/net/ieee80211/ieee80211_rx.c
@@ -369,7 +369,6 @@
/* Put this code here so that we avoid duplicating it in all
* Rx paths. - Jean II */
-#ifdef CONFIG_WIRELESS_EXT
#ifdef IW_WIRELESS_SPY /* defined in iw_handler.h */
/* If spy monitoring on */
if (ieee->spy_data.spy_number > 0) {
@@ -398,7 +397,6 @@
wireless_spy_update(ieee->dev, hdr->addr2, &wstats);
}
#endif /* IW_WIRELESS_SPY */
-#endif /* CONFIG_WIRELESS_EXT */
#ifdef NOT_YET
hostap_update_rx_stats(local->ap, hdr, rx_stats);
@@ -1692,8 +1690,8 @@
WLAN_FC_GET_STYPE(le16_to_cpu
(header->frame_ctl)));
- IEEE80211_WARNING("%s: IEEE80211_REASSOC_REQ received\n",
- ieee->dev->name);
+ IEEE80211_DEBUG_MGMT("%s: IEEE80211_REASSOC_REQ received\n",
+ ieee->dev->name);
if (ieee->handle_reassoc_request != NULL)
ieee->handle_reassoc_request(ieee->dev,
(struct ieee80211_reassoc_request *)
@@ -1705,8 +1703,8 @@
WLAN_FC_GET_STYPE(le16_to_cpu
(header->frame_ctl)));
- IEEE80211_WARNING("%s: IEEE80211_ASSOC_REQ received\n",
- ieee->dev->name);
+ IEEE80211_DEBUG_MGMT("%s: IEEE80211_ASSOC_REQ received\n",
+ ieee->dev->name);
if (ieee->handle_assoc_request != NULL)
ieee->handle_assoc_request(ieee->dev);
break;
@@ -1722,10 +1720,10 @@
IEEE80211_DEBUG_MGMT("received UNKNOWN (%d)\n",
WLAN_FC_GET_STYPE(le16_to_cpu
(header->frame_ctl)));
- IEEE80211_WARNING("%s: Unknown management packet: %d\n",
- ieee->dev->name,
- WLAN_FC_GET_STYPE(le16_to_cpu
- (header->frame_ctl)));
+ IEEE80211_DEBUG_MGMT("%s: Unknown management packet: %d\n",
+ ieee->dev->name,
+ WLAN_FC_GET_STYPE(le16_to_cpu
+ (header->frame_ctl)));
break;
}
}
diff --git a/net/ieee80211/ieee80211_tx.c b/net/ieee80211/ieee80211_tx.c
index 8b4332f..233d527 100644
--- a/net/ieee80211/ieee80211_tx.c
+++ b/net/ieee80211/ieee80211_tx.c
@@ -220,13 +220,43 @@
return txb;
}
+static int ieee80211_classify(struct sk_buff *skb)
+{
+ struct ethhdr *eth;
+ struct iphdr *ip;
+
+ eth = (struct ethhdr *)skb->data;
+ if (eth->h_proto != __constant_htons(ETH_P_IP))
+ return 0;
+
+ ip = skb->nh.iph;
+ switch (ip->tos & 0xfc) {
+ case 0x20:
+ return 2;
+ case 0x40:
+ return 1;
+ case 0x60:
+ return 3;
+ case 0x80:
+ return 4;
+ case 0xa0:
+ return 5;
+ case 0xc0:
+ return 6;
+ case 0xe0:
+ return 7;
+ default:
+ return 0;
+ }
+}
+
/* Incoming skb is converted to a txb which consists of
* a block of 802.11 fragment packets (stored as skbs) */
int ieee80211_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct ieee80211_device *ieee = netdev_priv(dev);
struct ieee80211_txb *txb = NULL;
- struct ieee80211_hdr_3addr *frag_hdr;
+ struct ieee80211_hdr_3addrqos *frag_hdr;
int i, bytes_per_frag, nr_frags, bytes_last_frag, frag_size,
rts_required;
unsigned long flags;
@@ -234,9 +264,10 @@
int ether_type, encrypt, host_encrypt, host_encrypt_msdu, host_build_iv;
int bytes, fc, hdr_len;
struct sk_buff *skb_frag;
- struct ieee80211_hdr_3addr header = { /* Ensure zero initialized */
+ struct ieee80211_hdr_3addrqos header = {/* Ensure zero initialized */
.duration_id = 0,
- .seq_ctl = 0
+ .seq_ctl = 0,
+ .qos_ctl = 0
};
u8 dest[ETH_ALEN], src[ETH_ALEN];
struct ieee80211_crypt_data *crypt;
@@ -282,12 +313,6 @@
memcpy(dest, skb->data, ETH_ALEN);
memcpy(src, skb->data + ETH_ALEN, ETH_ALEN);
- /* Advance the SKB to the start of the payload */
- skb_pull(skb, sizeof(struct ethhdr));
-
- /* Determine total amount of storage required for TXB packets */
- bytes = skb->len + SNAP_SIZE + sizeof(u16);
-
if (host_encrypt || host_build_iv)
fc = IEEE80211_FTYPE_DATA | IEEE80211_STYPE_DATA |
IEEE80211_FCTL_PROTECTED;
@@ -306,9 +331,23 @@
memcpy(header.addr2, src, ETH_ALEN);
memcpy(header.addr3, ieee->bssid, ETH_ALEN);
}
- header.frame_ctl = cpu_to_le16(fc);
hdr_len = IEEE80211_3ADDR_LEN;
+ if (ieee->is_qos_active && ieee->is_qos_active(dev, skb)) {
+ fc |= IEEE80211_STYPE_QOS_DATA;
+ hdr_len += 2;
+
+ skb->priority = ieee80211_classify(skb);
+ header.qos_ctl |= skb->priority & IEEE80211_QCTL_TID;
+ }
+ header.frame_ctl = cpu_to_le16(fc);
+
+ /* Advance the SKB to the start of the payload */
+ skb_pull(skb, sizeof(struct ethhdr));
+
+ /* Determine total amount of storage required for TXB packets */
+ bytes = skb->len + SNAP_SIZE + sizeof(u16);
+
/* Encrypt msdu first on the whole data packet. */
if ((host_encrypt || host_encrypt_msdu) &&
crypt && crypt->ops && crypt->ops->encrypt_msdu) {
@@ -402,7 +441,7 @@
if (rts_required) {
skb_frag = txb->fragments[0];
frag_hdr =
- (struct ieee80211_hdr_3addr *)skb_put(skb_frag, hdr_len);
+ (struct ieee80211_hdr_3addrqos *)skb_put(skb_frag, hdr_len);
/*
* Set header frame_ctl to the RTS.
@@ -433,7 +472,7 @@
crypt->ops->extra_mpdu_prefix_len);
frag_hdr =
- (struct ieee80211_hdr_3addr *)skb_put(skb_frag, hdr_len);
+ (struct ieee80211_hdr_3addrqos *)skb_put(skb_frag, hdr_len);
memcpy(frag_hdr, &header, hdr_len);
/* If this is not the last fragment, then add the MOREFRAGS
diff --git a/net/ieee80211/ieee80211_wx.c b/net/ieee80211/ieee80211_wx.c
index b885fd1..0ea55cb 100644
--- a/net/ieee80211/ieee80211_wx.c
+++ b/net/ieee80211/ieee80211_wx.c
@@ -50,7 +50,8 @@
char *p;
struct iw_event iwe;
int i, j;
- u8 max_rate, rate;
+ char *current_val; /* For rates */
+ u8 rate;
/* First entry *MUST* be the AP MAC address */
iwe.cmd = SIOCGIWAP;
@@ -107,9 +108,13 @@
start = iwe_stream_add_point(start, stop, &iwe, network->ssid);
/* Add basic and extended rates */
- max_rate = 0;
- p = custom;
- p += snprintf(p, MAX_CUSTOM_LEN - (p - custom), " Rates (Mb/s): ");
+ /* Rate : stuffing multiple values in a single event require a bit
+ * more of magic - Jean II */
+ current_val = start + IW_EV_LCP_LEN;
+ iwe.cmd = SIOCGIWRATE;
+ /* Those two flags are ignored... */
+ iwe.u.bitrate.fixed = iwe.u.bitrate.disabled = 0;
+
for (i = 0, j = 0; i < network->rates_len;) {
if (j < network->rates_ex_len &&
((network->rates_ex[j] & 0x7F) <
@@ -117,28 +122,21 @@
rate = network->rates_ex[j++] & 0x7F;
else
rate = network->rates[i++] & 0x7F;
- if (rate > max_rate)
- max_rate = rate;
- p += snprintf(p, MAX_CUSTOM_LEN - (p - custom),
- "%d%s ", rate >> 1, (rate & 1) ? ".5" : "");
+ /* Bit rate given in 500 kb/s units (+ 0x80) */
+ iwe.u.bitrate.value = ((rate & 0x7f) * 500000);
+ /* Add new value to event */
+ current_val = iwe_stream_add_value(start, current_val, stop, &iwe, IW_EV_PARAM_LEN);
}
for (; j < network->rates_ex_len; j++) {
rate = network->rates_ex[j] & 0x7F;
- p += snprintf(p, MAX_CUSTOM_LEN - (p - custom),
- "%d%s ", rate >> 1, (rate & 1) ? ".5" : "");
- if (rate > max_rate)
- max_rate = rate;
+ /* Bit rate given in 500 kb/s units (+ 0x80) */
+ iwe.u.bitrate.value = ((rate & 0x7f) * 500000);
+ /* Add new value to event */
+ current_val = iwe_stream_add_value(start, current_val, stop, &iwe, IW_EV_PARAM_LEN);
}
-
- iwe.cmd = SIOCGIWRATE;
- iwe.u.bitrate.fixed = iwe.u.bitrate.disabled = 0;
- iwe.u.bitrate.value = max_rate * 500000;
- start = iwe_stream_add_event(start, stop, &iwe, IW_EV_PARAM_LEN);
-
- iwe.cmd = IWEVCUSTOM;
- iwe.u.data.length = p - custom;
- if (iwe.u.data.length)
- start = iwe_stream_add_point(start, stop, &iwe, custom);
+ /* Check if we added any rate */
+ if((current_val - start) > IW_EV_LCP_LEN)
+ start = current_val;
/* Add quality statistics */
iwe.cmd = IWEVQUAL;
diff --git a/net/ieee80211/softmac/ieee80211softmac_assoc.c b/net/ieee80211/softmac/ieee80211softmac_assoc.c
index fb79ce7..ea9f5aa 100644
--- a/net/ieee80211/softmac/ieee80211softmac_assoc.c
+++ b/net/ieee80211/softmac/ieee80211softmac_assoc.c
@@ -82,7 +82,7 @@
}
/* Sends out a disassociation request to the desired AP */
-static void
+void
ieee80211softmac_disassoc(struct ieee80211softmac_device *mac, u16 reason)
{
unsigned long flags;
diff --git a/net/ieee80211/softmac/ieee80211softmac_event.c b/net/ieee80211/softmac/ieee80211softmac_event.c
index 8cc8f3f..4b153f7 100644
--- a/net/ieee80211/softmac/ieee80211softmac_event.c
+++ b/net/ieee80211/softmac/ieee80211softmac_event.c
@@ -38,7 +38,8 @@
* The event context is private and can only be used from
* within this module. Its meaning varies with the event
* type:
- * SCAN_FINISHED: no special meaning
+ * SCAN_FINISHED,
+ * DISASSOCIATED: NULL
* ASSOCIATED,
* ASSOCIATE_FAILED,
* ASSOCIATE_TIMEOUT,
@@ -59,15 +60,15 @@
*/
static char *event_descriptions[IEEE80211SOFTMAC_EVENT_LAST+1] = {
- "scan finished",
- "associated",
+ NULL, /* scan finished */
+ NULL, /* associated */
"associating failed",
"associating timed out",
"authenticated",
"authenticating failed",
"authenticating timed out",
"associating failed because no suitable network was found",
- "disassociated",
+ NULL, /* disassociated */
};
@@ -136,30 +137,24 @@
int we_event;
char *msg = NULL;
+ memset(&wrqu, '\0', sizeof (union iwreq_data));
+
switch(event) {
case IEEE80211SOFTMAC_EVENT_ASSOCIATED:
network = (struct ieee80211softmac_network *)event_ctx;
- wrqu.data.length = 0;
- wrqu.data.flags = 0;
memcpy(wrqu.ap_addr.sa_data, &network->bssid[0], ETH_ALEN);
- wrqu.ap_addr.sa_family = ARPHRD_ETHER;
- we_event = SIOCGIWAP;
- break;
+ /* fall through */
case IEEE80211SOFTMAC_EVENT_DISASSOCIATED:
- wrqu.data.length = 0;
- wrqu.data.flags = 0;
- memset(&wrqu, '\0', sizeof (union iwreq_data));
wrqu.ap_addr.sa_family = ARPHRD_ETHER;
we_event = SIOCGIWAP;
break;
case IEEE80211SOFTMAC_EVENT_SCAN_FINISHED:
- wrqu.data.length = 0;
- wrqu.data.flags = 0;
- memset(&wrqu, '\0', sizeof (union iwreq_data));
we_event = SIOCGIWSCAN;
break;
default:
msg = event_descriptions[event];
+ if (!msg)
+ msg = "SOFTMAC EVENT BUG";
wrqu.data.length = strlen(msg);
we_event = IWEVCUSTOM;
break;
diff --git a/net/ieee80211/softmac/ieee80211softmac_priv.h b/net/ieee80211/softmac/ieee80211softmac_priv.h
index 65d9816..8c95b3a 100644
--- a/net/ieee80211/softmac/ieee80211softmac_priv.h
+++ b/net/ieee80211/softmac/ieee80211softmac_priv.h
@@ -150,6 +150,7 @@
int ieee80211softmac_handle_reassoc_req(struct net_device * dev,
struct ieee80211_reassoc_request * reassoc);
void ieee80211softmac_assoc_timeout(void *d);
+void ieee80211softmac_disassoc(struct ieee80211softmac_device *mac, u16 reason);
/* some helper functions */
static inline int ieee80211softmac_scan_handlers_check_self(struct ieee80211softmac_device *sm)
diff --git a/net/ieee80211/softmac/ieee80211softmac_wx.c b/net/ieee80211/softmac/ieee80211softmac_wx.c
index 27edb2b..8d0c226 100644
--- a/net/ieee80211/softmac/ieee80211softmac_wx.c
+++ b/net/ieee80211/softmac/ieee80211softmac_wx.c
@@ -431,3 +431,35 @@
}
EXPORT_SYMBOL_GPL(ieee80211softmac_wx_get_genie);
+int
+ieee80211softmac_wx_set_mlme(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ struct ieee80211softmac_device *mac = ieee80211_priv(dev);
+ struct iw_mlme *mlme = (struct iw_mlme *)extra;
+ u16 reason = cpu_to_le16(mlme->reason_code);
+ struct ieee80211softmac_network *net;
+
+ if (memcmp(mac->associnfo.bssid, mlme->addr.sa_data, ETH_ALEN)) {
+ printk(KERN_DEBUG PFX "wx_set_mlme: requested operation on net we don't use\n");
+ return -EINVAL;
+ }
+
+ switch (mlme->cmd) {
+ case IW_MLME_DEAUTH:
+ net = ieee80211softmac_get_network_by_bssid_locked(mac, mlme->addr.sa_data);
+ if (!net) {
+ printk(KERN_DEBUG PFX "wx_set_mlme: we should know the net here...\n");
+ return -EINVAL;
+ }
+ return ieee80211softmac_deauth_req(mac, net, reason);
+ case IW_MLME_DISASSOC:
+ ieee80211softmac_disassoc(mac, reason);
+ return 0;
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+EXPORT_SYMBOL_GPL(ieee80211softmac_wx_set_mlme);