Merge tag 'bcm2835-dt-next-2016-02-17' into devicetree/next
This pull request covers mostly DT changes that didn't make it into
4.5 because required header files went through other trees, plus the
AUX uart support this time around.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d000814..c8d6b8a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -80,6 +80,7 @@
bcm4709-buffalo-wxr-1900dhp.dtb \
bcm4709-netgear-r7000.dtb \
bcm4709-netgear-r8000.dtb \
+ bcm47094-dlink-dir-885l.dtb \
bcm94708.dtb \
bcm94709.dtb \
bcm953012k.dtb
diff --git a/arch/arm/boot/dts/bcm-cygnus-clock.dtsi b/arch/arm/boot/dts/bcm-cygnus-clock.dtsi
index 32bcd45..80b6ba4 100644
--- a/arch/arm/boot/dts/bcm-cygnus-clock.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus-clock.dtsi
@@ -121,4 +121,13 @@
clocks = <&osc>;
clock-output-names = "keypad", "adc/touch", "pwm";
};
+
+ audiopll: audiopll {
+ #clock-cells = <1>;
+ compatible = "brcm,cygnus-audiopll";
+ reg = <0x180aeb00 0x68>;
+ clocks = <&osc>;
+ clock-output-names = "audiopll", "ch0_audio",
+ "ch1_audio", "ch2_audio";
+ };
};
diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
index 10bdef5..def9e78 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -45,14 +45,14 @@
#address-cells = <1>;
#size-cells = <0>;
- cpu@0 {
+ cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a9";
next-level-cache = <&L2>;
reg = <0x0>;
};
- cpu@1 {
+ cpu1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a9";
next-level-cache = <&L2>;
@@ -62,24 +62,19 @@
};
};
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>;
+ };
+
mpcore {
compatible = "simple-bus";
ranges = <0x00000000 0x19000000 0x00023000>;
#address-cells = <1>;
#size-cells = <1>;
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- device_type = "cpu";
- compatible = "arm,cortex-a9";
- next-level-cache = <&L2>;
- reg = <0x0>;
- };
- };
-
a9pll: arm_clk@00000 {
#clock-cells = <0>;
compatible = "brcm,nsp-armpll";
@@ -169,6 +164,18 @@
#address-cells = <1>;
#size-cells = <1>;
+ gpioa: gpio@0020 {
+ compatible = "brcm,nsp-gpio-a";
+ reg = <0x0020 0x70>,
+ <0x3f1c4 0x1c>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ ngpios = <32>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-ranges = <&pinctrl 0 0 32>;
+ };
+
uart0: serial@0300 {
compatible = "ns16550a";
reg = <0x0300 0x100>;
@@ -185,78 +192,6 @@
status = "disabled";
};
- pcie0: pcie@12000 {
- compatible = "brcm,iproc-pcie";
- reg = <0x12000 0x1000>;
-
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_NONE>;
-
- linux,pci-domain = <0>;
-
- bus-range = <0x00 0xff>;
-
- #address-cells = <3>;
- #size-cells = <2>;
- device_type = "pci";
-
- /* Note: The HW does not support I/O resources. So,
- * only the memory resource range is being specified.
- */
- ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
-
- status = "disabled";
- };
-
- pcie1: pcie@13000 {
- compatible = "brcm,iproc-pcie";
- reg = <0x13000 0x1000>;
-
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_NONE>;
-
- linux,pci-domain = <1>;
-
- bus-range = <0x00 0xff>;
-
- #address-cells = <3>;
- #size-cells = <2>;
- device_type = "pci";
-
- /* Note: The HW does not support I/O resources. So,
- * only the memory resource range is being specified.
- */
- ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
-
- status = "disabled";
- };
-
- pcie2: pcie@14000 {
- compatible = "brcm,iproc-pcie";
- reg = <0x14000 0x1000>;
-
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_NONE>;
-
- linux,pci-domain = <2>;
-
- bus-range = <0x00 0xff>;
-
- #address-cells = <3>;
- #size-cells = <2>;
- device_type = "pci";
-
- /* Note: The HW does not support I/O resources. So,
- * only the memory resource range is being specified.
- */
- ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>;
-
- status = "disabled";
- };
-
nand: nand@26000 {
compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
reg = <0x026000 0x600>,
@@ -271,6 +206,24 @@
brcm,nand-has-wp;
};
+ ccbtimer0: timer@34000 {
+ compatible = "arm,sp804";
+ reg = <0x34000 0x1000>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&iprocslow>;
+ clock-names = "apb_pclk";
+ };
+
+ ccbtimer1: timer@35000 {
+ compatible = "arm,sp804";
+ reg = <0x35000 0x1000>;
+ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&iprocslow>;
+ clock-names = "apb_pclk";
+ };
+
i2c0: i2c@38000 {
compatible = "brcm,iproc-i2c";
reg = <0x38000 0x50>;
@@ -280,6 +233,14 @@
clock-frequency = <100000>;
};
+ watchdog@39000 {
+ compatible = "arm,sp805", "arm,primecell";
+ reg = <0x39000 0x1000>;
+ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&iprocslow>, <&iprocslow>;
+ clock-names = "wdogclk", "apb_pclk";
+ };
+
lcpll0: lcpll0@3f100 {
#clock-cells = <1>;
compatible = "brcm,nsp-lcpll0";
@@ -306,4 +267,76 @@
<0x3f408 0x04>;
};
};
+
+ pcie0: pcie@18012000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18012000 0x1000>;
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_NONE>;
+
+ linux,pci-domain = <0>;
+
+ bus-range = <0x00 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+
+ /* Note: The HW does not support I/O resources. So,
+ * only the memory resource range is being specified.
+ */
+ ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
+
+ status = "disabled";
+ };
+
+ pcie1: pcie@18013000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18013000 0x1000>;
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_NONE>;
+
+ linux,pci-domain = <1>;
+
+ bus-range = <0x00 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+
+ /* Note: The HW does not support I/O resources. So,
+ * only the memory resource range is being specified.
+ */
+ ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
+
+ status = "disabled";
+ };
+
+ pcie2: pcie@18014000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18014000 0x1000>;
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_NONE>;
+
+ linux,pci-domain = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+
+ /* Note: The HW does not support I/O resources. So,
+ * only the memory resource range is being specified.
+ */
+ ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>;
+
+ status = "disabled";
+ };
};
diff --git a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
new file mode 100644
index 0000000..6c83538
--- /dev/null
+++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
@@ -0,0 +1,111 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for D-Link DIR-885L
+ *
+ * Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+ compatible = "dlink,dir-885l", "brcm,bcm47094", "brcm,bcm4708";
+ model = "D-Link DIR-885L";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ memory {
+ reg = <0x00000000 0x08000000>;
+ };
+
+ nand: nand@18028000 {
+ nandcs@0 {
+ partition@0 {
+ label = "firmware";
+ reg = <0x00000000 0x08000000>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power-white {
+ label = "bcm53xx:white:power";
+ gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-on";
+ };
+
+ wan-white {
+ label = "bcm53xx:white:wan";
+ gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-off";
+ };
+
+ power-amber {
+ label = "bcm53xx:amber:power";
+ gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-off";
+ };
+
+ wan-amber {
+ label = "bcm53xx:amber:wan";
+ gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-off";
+ };
+
+ usb3-white {
+ label = "bcm53xx:white:usb3";
+ gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-off";
+ };
+
+ 2ghz {
+ label = "bcm53xx:white:2ghz";
+ gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-off";
+ };
+
+ 5ghz {
+ label = "bcm53xx:white:5ghz";
+ gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-off";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wps {
+ label = "WPS";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+ };
+
+ /* Switch: router / extender */
+ extender {
+ label = "Extender";
+ linux,code = <BTN_0>;
+ gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+ };
+
+ restart {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+ clock-frequency = <125000000>;
+};