| /* |
| * Synopsys Designware PCIe host controller driver |
| * |
| * Copyright (C) 2013 Samsung Electronics Co., Ltd. |
| * http://www.samsung.com |
| * |
| * Author: Jingoo Han <jg1.han@samsung.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/of.h> |
| #include <linux/types.h> |
| |
| #include "pcie-designware.h" |
| |
| /* PCIe Port Logic registers */ |
| #define PLR_OFFSET 0x700 |
| #define PCIE_PHY_DEBUG_R1 (PLR_OFFSET + 0x2c) |
| #define PCIE_PHY_DEBUG_R1_LINK_UP (0x1 << 4) |
| #define PCIE_PHY_DEBUG_R1_LINK_IN_TRAINING (0x1 << 29) |
| |
| int dw_pcie_read(void __iomem *addr, int size, u32 *val) |
| { |
| if ((uintptr_t)addr & (size - 1)) { |
| *val = 0; |
| return PCIBIOS_BAD_REGISTER_NUMBER; |
| } |
| |
| if (size == 4) { |
| *val = readl(addr); |
| } else if (size == 2) { |
| *val = readw(addr); |
| } else if (size == 1) { |
| *val = readb(addr); |
| } else { |
| *val = 0; |
| return PCIBIOS_BAD_REGISTER_NUMBER; |
| } |
| |
| return PCIBIOS_SUCCESSFUL; |
| } |
| |
| int dw_pcie_write(void __iomem *addr, int size, u32 val) |
| { |
| if ((uintptr_t)addr & (size - 1)) |
| return PCIBIOS_BAD_REGISTER_NUMBER; |
| |
| if (size == 4) |
| writel(val, addr); |
| else if (size == 2) |
| writew(val, addr); |
| else if (size == 1) |
| writeb(val, addr); |
| else |
| return PCIBIOS_BAD_REGISTER_NUMBER; |
| |
| return PCIBIOS_SUCCESSFUL; |
| } |
| |
| u32 __dw_pcie_read_dbi(struct dw_pcie *pci, void __iomem *base, u32 reg, |
| size_t size) |
| { |
| int ret; |
| u32 val; |
| |
| if (pci->ops->read_dbi) |
| return pci->ops->read_dbi(pci, base, reg, size); |
| |
| ret = dw_pcie_read(base + reg, size, &val); |
| if (ret) |
| dev_err(pci->dev, "read DBI address failed\n"); |
| |
| return val; |
| } |
| |
| void __dw_pcie_write_dbi(struct dw_pcie *pci, void __iomem *base, u32 reg, |
| size_t size, u32 val) |
| { |
| int ret; |
| |
| if (pci->ops->write_dbi) { |
| pci->ops->write_dbi(pci, base, reg, size, val); |
| return; |
| } |
| |
| ret = dw_pcie_write(base + reg, size, val); |
| if (ret) |
| dev_err(pci->dev, "write DBI address failed\n"); |
| } |
| |
| static u32 dw_pcie_readl_ob_unroll(struct dw_pcie *pci, u32 index, u32 reg) |
| { |
| u32 offset = PCIE_GET_ATU_OUTB_UNR_REG_OFFSET(index); |
| |
| return dw_pcie_readl_dbi(pci, offset + reg); |
| } |
| |
| static void dw_pcie_writel_ob_unroll(struct dw_pcie *pci, u32 index, u32 reg, |
| u32 val) |
| { |
| u32 offset = PCIE_GET_ATU_OUTB_UNR_REG_OFFSET(index); |
| |
| dw_pcie_writel_dbi(pci, offset + reg, val); |
| } |
| |
| void dw_pcie_prog_outbound_atu_unroll(struct dw_pcie *pci, int index, int type, |
| u64 cpu_addr, u64 pci_addr, u32 size) |
| { |
| u32 retries, val; |
| |
| dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_LOWER_BASE, |
| lower_32_bits(cpu_addr)); |
| dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_UPPER_BASE, |
| upper_32_bits(cpu_addr)); |
| dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_LIMIT, |
| lower_32_bits(cpu_addr + size - 1)); |
| dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_LOWER_TARGET, |
| lower_32_bits(pci_addr)); |
| dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_UPPER_TARGET, |
| upper_32_bits(pci_addr)); |
| dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_REGION_CTRL1, |
| type); |
| dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_REGION_CTRL2, |
| PCIE_ATU_ENABLE); |
| |
| /* |
| * Make sure ATU enable takes effect before any subsequent config |
| * and I/O accesses. |
| */ |
| for (retries = 0; retries < LINK_WAIT_MAX_IATU_RETRIES; retries++) { |
| val = dw_pcie_readl_ob_unroll(pci, index, |
| PCIE_ATU_UNR_REGION_CTRL2); |
| if (val & PCIE_ATU_ENABLE) |
| return; |
| |
| usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); |
| } |
| dev_err(pci->dev, "outbound iATU is not being enabled\n"); |
| } |
| |
| void dw_pcie_prog_outbound_atu(struct dw_pcie *pci, int index, int type, |
| u64 cpu_addr, u64 pci_addr, u32 size) |
| { |
| u32 retries, val; |
| |
| if (pci->ops->cpu_addr_fixup) |
| cpu_addr = pci->ops->cpu_addr_fixup(cpu_addr); |
| |
| if (pci->iatu_unroll_enabled) { |
| dw_pcie_prog_outbound_atu_unroll(pci, index, type, cpu_addr, |
| pci_addr, size); |
| return; |
| } |
| |
| dw_pcie_writel_dbi(pci, PCIE_ATU_VIEWPORT, |
| PCIE_ATU_REGION_OUTBOUND | index); |
| dw_pcie_writel_dbi(pci, PCIE_ATU_LOWER_BASE, |
| lower_32_bits(cpu_addr)); |
| dw_pcie_writel_dbi(pci, PCIE_ATU_UPPER_BASE, |
| upper_32_bits(cpu_addr)); |
| dw_pcie_writel_dbi(pci, PCIE_ATU_LIMIT, |
| lower_32_bits(cpu_addr + size - 1)); |
| dw_pcie_writel_dbi(pci, PCIE_ATU_LOWER_TARGET, |
| lower_32_bits(pci_addr)); |
| dw_pcie_writel_dbi(pci, PCIE_ATU_UPPER_TARGET, |
| upper_32_bits(pci_addr)); |
| dw_pcie_writel_dbi(pci, PCIE_ATU_CR1, type); |
| dw_pcie_writel_dbi(pci, PCIE_ATU_CR2, PCIE_ATU_ENABLE); |
| |
| /* |
| * Make sure ATU enable takes effect before any subsequent config |
| * and I/O accesses. |
| */ |
| for (retries = 0; retries < LINK_WAIT_MAX_IATU_RETRIES; retries++) { |
| val = dw_pcie_readl_dbi(pci, PCIE_ATU_CR2); |
| if (val == PCIE_ATU_ENABLE) |
| return; |
| |
| usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); |
| } |
| dev_err(pci->dev, "outbound iATU is not being enabled\n"); |
| } |
| |
| static u32 dw_pcie_readl_ib_unroll(struct dw_pcie *pci, u32 index, u32 reg) |
| { |
| u32 offset = PCIE_GET_ATU_INB_UNR_REG_OFFSET(index); |
| |
| return dw_pcie_readl_dbi(pci, offset + reg); |
| } |
| |
| static void dw_pcie_writel_ib_unroll(struct dw_pcie *pci, u32 index, u32 reg, |
| u32 val) |
| { |
| u32 offset = PCIE_GET_ATU_INB_UNR_REG_OFFSET(index); |
| |
| dw_pcie_writel_dbi(pci, offset + reg, val); |
| } |
| |
| int dw_pcie_prog_inbound_atu_unroll(struct dw_pcie *pci, int index, int bar, |
| u64 cpu_addr, enum dw_pcie_as_type as_type) |
| { |
| int type; |
| u32 retries, val; |
| |
| dw_pcie_writel_ib_unroll(pci, index, PCIE_ATU_UNR_LOWER_TARGET, |
| lower_32_bits(cpu_addr)); |
| dw_pcie_writel_ib_unroll(pci, index, PCIE_ATU_UNR_UPPER_TARGET, |
| upper_32_bits(cpu_addr)); |
| |
| switch (as_type) { |
| case DW_PCIE_AS_MEM: |
| type = PCIE_ATU_TYPE_MEM; |
| break; |
| case DW_PCIE_AS_IO: |
| type = PCIE_ATU_TYPE_IO; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| dw_pcie_writel_ib_unroll(pci, index, PCIE_ATU_UNR_REGION_CTRL1, type); |
| dw_pcie_writel_ib_unroll(pci, index, PCIE_ATU_UNR_REGION_CTRL2, |
| PCIE_ATU_ENABLE | |
| PCIE_ATU_BAR_MODE_ENABLE | (bar << 8)); |
| |
| /* |
| * Make sure ATU enable takes effect before any subsequent config |
| * and I/O accesses. |
| */ |
| for (retries = 0; retries < LINK_WAIT_MAX_IATU_RETRIES; retries++) { |
| val = dw_pcie_readl_ib_unroll(pci, index, |
| PCIE_ATU_UNR_REGION_CTRL2); |
| if (val & PCIE_ATU_ENABLE) |
| return 0; |
| |
| usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); |
| } |
| dev_err(pci->dev, "inbound iATU is not being enabled\n"); |
| |
| return -EBUSY; |
| } |
| |
| int dw_pcie_prog_inbound_atu(struct dw_pcie *pci, int index, int bar, |
| u64 cpu_addr, enum dw_pcie_as_type as_type) |
| { |
| int type; |
| u32 retries, val; |
| |
| if (pci->iatu_unroll_enabled) |
| return dw_pcie_prog_inbound_atu_unroll(pci, index, bar, |
| cpu_addr, as_type); |
| |
| dw_pcie_writel_dbi(pci, PCIE_ATU_VIEWPORT, PCIE_ATU_REGION_INBOUND | |
| index); |
| dw_pcie_writel_dbi(pci, PCIE_ATU_LOWER_TARGET, lower_32_bits(cpu_addr)); |
| dw_pcie_writel_dbi(pci, PCIE_ATU_UPPER_TARGET, upper_32_bits(cpu_addr)); |
| |
| switch (as_type) { |
| case DW_PCIE_AS_MEM: |
| type = PCIE_ATU_TYPE_MEM; |
| break; |
| case DW_PCIE_AS_IO: |
| type = PCIE_ATU_TYPE_IO; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| dw_pcie_writel_dbi(pci, PCIE_ATU_CR1, type); |
| dw_pcie_writel_dbi(pci, PCIE_ATU_CR2, PCIE_ATU_ENABLE |
| | PCIE_ATU_BAR_MODE_ENABLE | (bar << 8)); |
| |
| /* |
| * Make sure ATU enable takes effect before any subsequent config |
| * and I/O accesses. |
| */ |
| for (retries = 0; retries < LINK_WAIT_MAX_IATU_RETRIES; retries++) { |
| val = dw_pcie_readl_dbi(pci, PCIE_ATU_CR2); |
| if (val & PCIE_ATU_ENABLE) |
| return 0; |
| |
| usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); |
| } |
| dev_err(pci->dev, "inbound iATU is not being enabled\n"); |
| |
| return -EBUSY; |
| } |
| |
| void dw_pcie_disable_atu(struct dw_pcie *pci, int index, |
| enum dw_pcie_region_type type) |
| { |
| int region; |
| |
| switch (type) { |
| case DW_PCIE_REGION_INBOUND: |
| region = PCIE_ATU_REGION_INBOUND; |
| break; |
| case DW_PCIE_REGION_OUTBOUND: |
| region = PCIE_ATU_REGION_OUTBOUND; |
| break; |
| default: |
| return; |
| } |
| |
| dw_pcie_writel_dbi(pci, PCIE_ATU_VIEWPORT, region | index); |
| dw_pcie_writel_dbi(pci, PCIE_ATU_CR2, ~PCIE_ATU_ENABLE); |
| } |
| |
| int dw_pcie_wait_for_link(struct dw_pcie *pci) |
| { |
| int retries; |
| |
| /* check if the link is up or not */ |
| for (retries = 0; retries < LINK_WAIT_MAX_RETRIES; retries++) { |
| if (dw_pcie_link_up(pci)) { |
| dev_info(pci->dev, "link up\n"); |
| return 0; |
| } |
| usleep_range(LINK_WAIT_USLEEP_MIN, LINK_WAIT_USLEEP_MAX); |
| } |
| |
| dev_err(pci->dev, "phy link never came up\n"); |
| |
| return -ETIMEDOUT; |
| } |
| |
| int dw_pcie_link_up(struct dw_pcie *pci) |
| { |
| u32 val; |
| |
| if (pci->ops->link_up) |
| return pci->ops->link_up(pci); |
| |
| val = readl(pci->dbi_base + PCIE_PHY_DEBUG_R1); |
| return ((val & PCIE_PHY_DEBUG_R1_LINK_UP) && |
| (!(val & PCIE_PHY_DEBUG_R1_LINK_IN_TRAINING))); |
| } |
| |
| void dw_pcie_setup(struct dw_pcie *pci) |
| { |
| int ret; |
| u32 val; |
| u32 lanes; |
| struct device *dev = pci->dev; |
| struct device_node *np = dev->of_node; |
| |
| ret = of_property_read_u32(np, "num-lanes", &lanes); |
| if (ret) |
| lanes = 0; |
| |
| /* set the number of lanes */ |
| val = dw_pcie_readl_dbi(pci, PCIE_PORT_LINK_CONTROL); |
| val &= ~PORT_LINK_MODE_MASK; |
| switch (lanes) { |
| case 1: |
| val |= PORT_LINK_MODE_1_LANES; |
| break; |
| case 2: |
| val |= PORT_LINK_MODE_2_LANES; |
| break; |
| case 4: |
| val |= PORT_LINK_MODE_4_LANES; |
| break; |
| case 8: |
| val |= PORT_LINK_MODE_8_LANES; |
| break; |
| default: |
| dev_err(pci->dev, "num-lanes %u: invalid value\n", lanes); |
| return; |
| } |
| dw_pcie_writel_dbi(pci, PCIE_PORT_LINK_CONTROL, val); |
| |
| /* set link width speed control register */ |
| val = dw_pcie_readl_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL); |
| val &= ~PORT_LOGIC_LINK_WIDTH_MASK; |
| switch (lanes) { |
| case 1: |
| val |= PORT_LOGIC_LINK_WIDTH_1_LANES; |
| break; |
| case 2: |
| val |= PORT_LOGIC_LINK_WIDTH_2_LANES; |
| break; |
| case 4: |
| val |= PORT_LOGIC_LINK_WIDTH_4_LANES; |
| break; |
| case 8: |
| val |= PORT_LOGIC_LINK_WIDTH_8_LANES; |
| break; |
| } |
| dw_pcie_writel_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL, val); |
| } |