MMC core learns about SPI
Teach the MMC/SD/SDIO core about using SPI mode.
- Use mmc_host_is_spi() so enumeration works through SPI signaling
and protocols, not just the native versions.
- Provide the SPI response type flags with each request issued,
including requests from the new lock/unlock code.
- Understand that cmd->resp[0] and mmc_get_status() results for SPI
return different values than for "native" MMC/SD protocol; this
affects resetting, checking card lock status, and some others.
- Understand that some commands act a bit differently ... notably:
* OP_COND command doesn't return the OCR
* APP_CMD status doesn't have an R1_APP_CMD analogue
Those changes required some new and updated primitives:
- Provide utilities to access two SPI-only requests, and one
request that wasn't previously needed:
* mmc_spi_read_ocr() ... SPI only
* mmc_spi_set_crc() ... SPI only (override by module parm)
* mmc_send_cid() ... for use without broadcast mode
- Updated internal routines:
* Previous mmc_send_csd() modified into mmc_send_cxd_native();
it uses native "R2" responses, which include 16 bytes of data.
* Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
helper for command-and-data access
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
- Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper
- Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
those helper routines based on whether they're native or SPI
The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index 6ba4589..65fe288 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -165,8 +165,6 @@
BUG_ON(!card);
- err = -EIO;
-
if (card->csd.mmca_vsn < CSD_SPEC_VER_4)
return 0;
@@ -280,9 +278,21 @@
goto err;
/*
+ * For SPI, enable CRC as appropriate.
+ */
+ if (mmc_host_is_spi(host)) {
+ err = mmc_spi_set_crc(host, use_spi_crc);
+ if (err)
+ goto err;
+ }
+
+ /*
* Fetch CID from card.
*/
- err = mmc_all_send_cid(host, cid);
+ if (mmc_host_is_spi(host))
+ err = mmc_send_cid(host, cid);
+ else
+ err = mmc_all_send_cid(host, cid);
if (err)
goto err;
@@ -309,13 +319,15 @@
}
/*
- * Set card RCA.
+ * For native busses: set card RCA and quit open drain mode.
*/
- err = mmc_set_relative_addr(card);
- if (err)
- goto free_card;
+ if (!mmc_host_is_spi(host)) {
+ err = mmc_set_relative_addr(card);
+ if (err)
+ goto free_card;
- mmc_set_bus_mode(host, MMC_BUSMODE_PUSHPULL);
+ mmc_set_bus_mode(host, MMC_BUSMODE_PUSHPULL);
+ }
if (!oldcard) {
/*
@@ -336,13 +348,15 @@
/*
* Select card, as all following commands rely on that.
*/
- err = mmc_select_card(card);
- if (err)
- goto free_card;
+ if (!mmc_host_is_spi(host)) {
+ err = mmc_select_card(card);
+ if (err)
+ goto free_card;
+ }
if (!oldcard) {
/*
- * Fetch and process extened CSD.
+ * Fetch and process extended CSD.
*/
err = mmc_read_ext_csd(card);
if (err)
@@ -502,7 +516,8 @@
BUG_ON(!host->card);
mmc_claim_host(host);
- mmc_deselect_cards(host);
+ if (!mmc_host_is_spi(host))
+ mmc_deselect_cards(host);
host->card->state &= ~MMC_STATE_HIGHSPEED;
mmc_release_host(host);
}
@@ -563,6 +578,15 @@
mmc_attach_bus(host, &mmc_ops);
/*
+ * We need to get OCR a different way for SPI.
+ */
+ if (mmc_host_is_spi(host)) {
+ err = mmc_spi_read_ocr(host, 1, &ocr);
+ if (err)
+ goto err;
+ }
+
+ /*
* Sanity check the voltages that the card claims to
* support.
*/