Merge tag 'imx-eukrea' of git://git.pengutronix.de/git/imx/linux-2.6 into next/boards
ARM i.MX Eukrea Patches for 3.5
By Eric Bénard (11) and Denis Carikli (1)
via Sascha Hauer
* tag 'imx-eukrea' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx: eukrea_mbimxsd rename to eukrea_mbimxsd51
ARM: imx: eukrea_mbimxsd25: use IMX_GPIO_NR
ARM: imx: eukrea_mbimxsd25: don't free twice GPIO_SWITCH1
ARM: imx: eukrea_mbimxsd: add backlight and lcd support
ARM: imx: eukrea_cpuimx51sd: support rev2 PCB
ARM: imx: eukrea_mbimxsd: add audio support
ARM: imx: eukrea_cpuimx51sd: add watchdog support
ARM: imx: eukrea-cpuimx51: remove board
ARM: imx: eukrea_mbimxsd35: add spi controler and spidev support
ARM: imx: eukrea_cpuimx25: add watchdog support
ARM: imx: eukrea_mbimxsd25: add spi controler and spidev support
ARM: imx: eukrea_cpuimx25: enable workaround ENGcm09152
diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig
index 6b31cb6..09a0296 100644
--- a/arch/arm/configs/imx_v4_v5_defconfig
+++ b/arch/arm/configs/imx_v4_v5_defconfig
@@ -92,6 +92,7 @@
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=m
+CONFIG_TOUCHSCREEN_MC13783=m
# CONFIG_SERIO is not set
# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_8250=m
@@ -107,7 +108,8 @@
CONFIG_W1=y
CONFIG_W1_MASTER_MXC=y
CONFIG_W1_SLAVE_THERM=y
-# CONFIG_HWMON is not set
+CONFIG_HWMON=m
+CONFIG_SENSORS_MC13783_ADC=m
CONFIG_WATCHDOG=y
CONFIG_IMX2_WDT=y
CONFIG_MFD_MC13XXX=y
diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
index f7b074f..748ba2e 100644
--- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
+++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
@@ -38,6 +38,7 @@
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
+#include <asm/system.h>
#include <mach/common.h>
#include <mach/iomux-mx27.h>
@@ -48,6 +49,14 @@
#define OTG_PHY_CS_GPIO (GPIO_PORTF + 17)
#define SDHC1_IRQ IRQ_GPIOB(25)
+#define MOTHERBOARD_BIT2 (GPIO_PORTD + 31)
+#define MOTHERBOARD_BIT1 (GPIO_PORTD + 30)
+#define MOTHERBOARD_BIT0 (GPIO_PORTD + 29)
+
+#define EXPBOARD_BIT2 (GPIO_PORTD + 25)
+#define EXPBOARD_BIT1 (GPIO_PORTD + 27)
+#define EXPBOARD_BIT0 (GPIO_PORTD + 28)
+
static const int visstrim_m10_pins[] __initconst = {
/* UART1 (console) */
PE12_PF_UART1_TXD,
@@ -119,6 +128,23 @@
PB19_PF_CSI_D7,
PB20_PF_CSI_VSYNC,
PB21_PF_CSI_HSYNC,
+ /* mother board version */
+ MOTHERBOARD_BIT2 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
+ MOTHERBOARD_BIT1 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
+ MOTHERBOARD_BIT0 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
+ /* expansion board version */
+ EXPBOARD_BIT2 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
+ EXPBOARD_BIT1 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
+ EXPBOARD_BIT0 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
+};
+
+static struct gpio visstrim_m10_version_gpios[] = {
+ { EXPBOARD_BIT0, GPIOF_IN, "exp-version-0" },
+ { EXPBOARD_BIT1, GPIOF_IN, "exp-version-1" },
+ { EXPBOARD_BIT2, GPIOF_IN, "exp-version-2" },
+ { MOTHERBOARD_BIT0, GPIOF_IN, "mother-version-0" },
+ { MOTHERBOARD_BIT1, GPIOF_IN, "mother-version-1" },
+ { MOTHERBOARD_BIT2, GPIOF_IN, "mother-version-2" },
};
/* Camera */
@@ -369,11 +395,40 @@
.flags = IMX_SSI_DMA | IMX_SSI_SYN,
};
+static void __init visstrim_m10_revision(void)
+{
+ int exp_version = 0;
+ int mo_version = 0;
+ int ret;
+
+ ret = gpio_request_array(visstrim_m10_version_gpios,
+ ARRAY_SIZE(visstrim_m10_version_gpios));
+ if (ret) {
+ pr_err("Failed to request version gpios");
+ return;
+ }
+
+ /* Get expansion board version (negative logic) */
+ exp_version |= !gpio_get_value(EXPBOARD_BIT2) << 2;
+ exp_version |= !gpio_get_value(EXPBOARD_BIT1) << 1;
+ exp_version |= !gpio_get_value(EXPBOARD_BIT0);
+
+ /* Get mother board version (negative logic) */
+ mo_version |= !gpio_get_value(MOTHERBOARD_BIT2) << 2;
+ mo_version |= !gpio_get_value(MOTHERBOARD_BIT1) << 1;
+ mo_version |= !gpio_get_value(MOTHERBOARD_BIT0);
+
+ system_rev = 0x27000;
+ system_rev |= (mo_version << 4);
+ system_rev |= exp_version;
+}
+
static void __init visstrim_m10_board_init(void)
{
int ret;
imx27_soc_init();
+ visstrim_m10_revision();
ret = mxc_gpio_setup_multiple_pins(visstrim_m10_pins,
ARRAY_SIZE(visstrim_m10_pins), "VISSTRIM_M10");
diff --git a/arch/arm/mach-imx/mach-mx35_3ds.c b/arch/arm/mach-imx/mach-mx35_3ds.c
index 6ae51c6..e99b016 100644
--- a/arch/arm/mach-imx/mach-mx35_3ds.c
+++ b/arch/arm/mach-imx/mach-mx35_3ds.c
@@ -34,6 +34,8 @@
#include <linux/usb/otg.h>
#include <linux/mtd/physmap.h>
+#include <linux/mfd/mc13892.h>
+#include <linux/regulator/machine.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -253,6 +255,8 @@
MX35_PAD_CSI_MCLK__IPU_CSI_MCLK,
MX35_PAD_CSI_PIXCLK__IPU_CSI_PIXCLK,
MX35_PAD_CSI_VSYNC__IPU_CSI_VSYNC,
+ /*PMIC IRQ*/
+ MX35_PAD_GPIO2_0__GPIO2_0,
};
/*
@@ -317,6 +321,193 @@
},
};
+static struct regulator_consumer_supply sw1_consumers[] = {
+ {
+ .supply = "cpu_vcc",
+ }
+};
+
+static struct regulator_consumer_supply vcam_consumers[] = {
+ /* sgtl5000 */
+ REGULATOR_SUPPLY("VDDA", "0-000a"),
+};
+
+static struct regulator_consumer_supply vaudio_consumers[] = {
+ REGULATOR_SUPPLY("cmos_vio", "soc-camera-pdrv.0"),
+};
+
+static struct regulator_init_data sw1_init = {
+ .constraints = {
+ .name = "SW1",
+ .min_uV = 600000,
+ .max_uV = 1375000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ .valid_modes_mask = 0,
+ .always_on = 1,
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(sw1_consumers),
+ .consumer_supplies = sw1_consumers,
+};
+
+static struct regulator_init_data sw2_init = {
+ .constraints = {
+ .name = "SW2",
+ .always_on = 1,
+ .boot_on = 1,
+ }
+};
+
+static struct regulator_init_data sw3_init = {
+ .constraints = {
+ .name = "SW3",
+ .always_on = 1,
+ .boot_on = 1,
+ }
+};
+
+static struct regulator_init_data sw4_init = {
+ .constraints = {
+ .name = "SW4",
+ .always_on = 1,
+ .boot_on = 1,
+ }
+};
+
+static struct regulator_init_data viohi_init = {
+ .constraints = {
+ .name = "VIOHI",
+ .boot_on = 1,
+ }
+};
+
+static struct regulator_init_data vusb_init = {
+ .constraints = {
+ .name = "VUSB",
+ .boot_on = 1,
+ }
+};
+
+static struct regulator_init_data vdig_init = {
+ .constraints = {
+ .name = "VDIG",
+ .boot_on = 1,
+ }
+};
+
+static struct regulator_init_data vpll_init = {
+ .constraints = {
+ .name = "VPLL",
+ .boot_on = 1,
+ }
+};
+
+static struct regulator_init_data vusb2_init = {
+ .constraints = {
+ .name = "VUSB2",
+ .boot_on = 1,
+ }
+};
+
+static struct regulator_init_data vvideo_init = {
+ .constraints = {
+ .name = "VVIDEO",
+ .boot_on = 1
+ }
+};
+
+static struct regulator_init_data vaudio_init = {
+ .constraints = {
+ .name = "VAUDIO",
+ .min_uV = 2300000,
+ .max_uV = 3000000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ .boot_on = 1
+ },
+ .num_consumer_supplies = ARRAY_SIZE(vaudio_consumers),
+ .consumer_supplies = vaudio_consumers,
+};
+
+static struct regulator_init_data vcam_init = {
+ .constraints = {
+ .name = "VCAM",
+ .min_uV = 2500000,
+ .max_uV = 3000000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_MODE,
+ .valid_modes_mask = REGULATOR_MODE_FAST | REGULATOR_MODE_NORMAL,
+ .boot_on = 1
+ },
+ .num_consumer_supplies = ARRAY_SIZE(vcam_consumers),
+ .consumer_supplies = vcam_consumers,
+};
+
+static struct regulator_init_data vgen1_init = {
+ .constraints = {
+ .name = "VGEN1",
+ }
+};
+
+static struct regulator_init_data vgen2_init = {
+ .constraints = {
+ .name = "VGEN2",
+ .boot_on = 1,
+ }
+};
+
+static struct regulator_init_data vgen3_init = {
+ .constraints = {
+ .name = "VGEN3",
+ }
+};
+
+static struct mc13xxx_regulator_init_data mx35_3ds_regulators[] = {
+ { .id = MC13892_SW1, .init_data = &sw1_init },
+ { .id = MC13892_SW2, .init_data = &sw2_init },
+ { .id = MC13892_SW3, .init_data = &sw3_init },
+ { .id = MC13892_SW4, .init_data = &sw4_init },
+ { .id = MC13892_VIOHI, .init_data = &viohi_init },
+ { .id = MC13892_VPLL, .init_data = &vpll_init },
+ { .id = MC13892_VDIG, .init_data = &vdig_init },
+ { .id = MC13892_VUSB2, .init_data = &vusb2_init },
+ { .id = MC13892_VVIDEO, .init_data = &vvideo_init },
+ { .id = MC13892_VAUDIO, .init_data = &vaudio_init },
+ { .id = MC13892_VCAM, .init_data = &vcam_init },
+ { .id = MC13892_VGEN1, .init_data = &vgen1_init },
+ { .id = MC13892_VGEN2, .init_data = &vgen2_init },
+ { .id = MC13892_VGEN3, .init_data = &vgen3_init },
+ { .id = MC13892_VUSB, .init_data = &vusb_init },
+};
+
+static struct mc13xxx_platform_data mx35_3ds_mc13892_data = {
+ .flags = MC13XXX_USE_RTC | MC13XXX_USE_TOUCHSCREEN,
+ .regulators = {
+ .num_regulators = ARRAY_SIZE(mx35_3ds_regulators),
+ .regulators = mx35_3ds_regulators,
+ },
+};
+
+#define GPIO_PMIC_INT IMX_GPIO_NR(2, 0)
+
+static struct i2c_board_info mx35_3ds_i2c_mc13892 = {
+
+ I2C_BOARD_INFO("mc13892", 0x08),
+ .platform_data = &mx35_3ds_mc13892_data,
+ .irq = IMX_GPIO_TO_IRQ(GPIO_PMIC_INT),
+};
+
+static void __init imx35_3ds_init_mc13892(void)
+{
+ int ret = gpio_request_one(GPIO_PMIC_INT, GPIOF_DIR_IN, "pmic irq");
+
+ if (ret) {
+ pr_err("failed to get pmic irq: %d\n", ret);
+ return;
+ }
+
+ i2c_register_board_info(0, &mx35_3ds_i2c_mc13892, 1);
+}
+
static int mx35_3ds_otg_init(struct platform_device *pdev)
{
return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERNAL_PHY);
@@ -412,6 +603,8 @@
imx35_fb_pdev = imx35_add_mx3_sdc_fb(&mx3fb_pdata);
mx35_3ds_lcd.dev.parent = &imx35_fb_pdev->dev;
platform_device_register(&mx35_3ds_lcd);
+
+ imx35_3ds_init_mc13892();
}
static void __init mx35pdk_timer_init(void)
diff --git a/arch/arm/mach-mmp/Kconfig b/arch/arm/mach-mmp/Kconfig
index 5a90b9a..fa03974 100644
--- a/arch/arm/mach-mmp/Kconfig
+++ b/arch/arm/mach-mmp/Kconfig
@@ -113,4 +113,11 @@
select CPU_PJ4
help
Select code specific to MMP2. MMP2 is ARMv7 compatible.
+
+config USB_EHCI_MV_U2O
+ bool "EHCI support for PXA USB OTG controller"
+ depends on USB_EHCI_MV
+ help
+ Enables support for OTG controller which can be switched to host mode.
+
endif
diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c
index bf5d8e1..223090b 100644
--- a/arch/arm/mach-mmp/aspenite.c
+++ b/arch/arm/mach-mmp/aspenite.c
@@ -17,6 +17,7 @@
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
#include <linux/interrupt.h>
+#include <linux/platform_data/mv_usb.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -221,6 +222,21 @@
.debounce_interval = 30,
};
+#if defined(CONFIG_USB_EHCI_MV)
+static char *pxa168_sph_clock_name[] = {
+ [0] = "PXA168-USBCLK",
+};
+
+static struct mv_usb_platform_data pxa168_sph_pdata = {
+ .clknum = 1,
+ .clkname = pxa168_sph_clock_name,
+ .mode = MV_USB_MODE_HOST,
+ .phy_init = pxa_usb_phy_init,
+ .phy_deinit = pxa_usb_phy_deinit,
+ .set_vbus = NULL,
+};
+#endif
+
static void __init common_init(void)
{
mfp_config(ARRAY_AND_SIZE(common_pin_config));
@@ -236,6 +252,10 @@
/* off-chip devices */
platform_device_register(&smc91x_device);
+
+#if defined(CONFIG_USB_EHCI_MV)
+ pxa168_add_usb_host(&pxa168_sph_pdata);
+#endif
}
MACHINE_START(ASPENITE, "PXA168-based Aspenite Development Platform")
diff --git a/arch/arm/mach-mmp/devices.c b/arch/arm/mach-mmp/devices.c
index 191d9de..dd2d8b1 100644
--- a/arch/arm/mach-mmp/devices.c
+++ b/arch/arm/mach-mmp/devices.c
@@ -9,9 +9,13 @@
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
+#include <linux/delay.h>
#include <asm/irq.h>
+#include <mach/irqs.h>
#include <mach/devices.h>
+#include <mach/cputype.h>
+#include <mach/regs-usb.h>
int __init pxa_register_device(struct pxa_device_desc *desc,
void *data, size_t size)
@@ -67,3 +71,281 @@
return platform_device_add(pdev);
}
+
+#if defined(CONFIG_USB) || defined(CONFIG_USB_GADGET)
+
+/*****************************************************************************
+ * The registers read/write routines
+ *****************************************************************************/
+
+static unsigned int u2o_get(void __iomem *base, unsigned int offset)
+{
+ return readl_relaxed(base + offset);
+}
+
+static void u2o_set(void __iomem *base, unsigned int offset,
+ unsigned int value)
+{
+ u32 reg;
+
+ reg = readl_relaxed(base + offset);
+ reg |= value;
+ writel_relaxed(reg, base + offset);
+ readl_relaxed(base + offset);
+}
+
+static void u2o_clear(void __iomem *base, unsigned int offset,
+ unsigned int value)
+{
+ u32 reg;
+
+ reg = readl_relaxed(base + offset);
+ reg &= ~value;
+ writel_relaxed(reg, base + offset);
+ readl_relaxed(base + offset);
+}
+
+static void u2o_write(void __iomem *base, unsigned int offset,
+ unsigned int value)
+{
+ writel_relaxed(value, base + offset);
+ readl_relaxed(base + offset);
+}
+
+#if defined(CONFIG_USB_MV_UDC) || defined(CONFIG_USB_EHCI_MV)
+
+#if defined(CONFIG_CPU_PXA910) || defined(CONFIG_CPU_PXA168)
+
+static DEFINE_MUTEX(phy_lock);
+static int phy_init_cnt;
+
+static int usb_phy_init_internal(void __iomem *base)
+{
+ int loops;
+
+ pr_info("Init usb phy!!!\n");
+
+ /* Initialize the USB PHY power */
+ if (cpu_is_pxa910()) {
+ u2o_set(base, UTMI_CTRL, (1<<UTMI_CTRL_INPKT_DELAY_SOF_SHIFT)
+ | (1<<UTMI_CTRL_PU_REF_SHIFT));
+ }
+
+ u2o_set(base, UTMI_CTRL, 1<<UTMI_CTRL_PLL_PWR_UP_SHIFT);
+ u2o_set(base, UTMI_CTRL, 1<<UTMI_CTRL_PWR_UP_SHIFT);
+
+ /* UTMI_PLL settings */
+ u2o_clear(base, UTMI_PLL, UTMI_PLL_PLLVDD18_MASK
+ | UTMI_PLL_PLLVDD12_MASK | UTMI_PLL_PLLCALI12_MASK
+ | UTMI_PLL_FBDIV_MASK | UTMI_PLL_REFDIV_MASK
+ | UTMI_PLL_ICP_MASK | UTMI_PLL_KVCO_MASK);
+
+ u2o_set(base, UTMI_PLL, 0xee<<UTMI_PLL_FBDIV_SHIFT
+ | 0xb<<UTMI_PLL_REFDIV_SHIFT | 3<<UTMI_PLL_PLLVDD18_SHIFT
+ | 3<<UTMI_PLL_PLLVDD12_SHIFT | 3<<UTMI_PLL_PLLCALI12_SHIFT
+ | 1<<UTMI_PLL_ICP_SHIFT | 3<<UTMI_PLL_KVCO_SHIFT);
+
+ /* UTMI_TX */
+ u2o_clear(base, UTMI_TX, UTMI_TX_REG_EXT_FS_RCAL_EN_MASK
+ | UTMI_TX_TXVDD12_MASK | UTMI_TX_CK60_PHSEL_MASK
+ | UTMI_TX_IMPCAL_VTH_MASK | UTMI_TX_REG_EXT_FS_RCAL_MASK
+ | UTMI_TX_AMP_MASK);
+ u2o_set(base, UTMI_TX, 3<<UTMI_TX_TXVDD12_SHIFT
+ | 4<<UTMI_TX_CK60_PHSEL_SHIFT | 4<<UTMI_TX_IMPCAL_VTH_SHIFT
+ | 8<<UTMI_TX_REG_EXT_FS_RCAL_SHIFT | 3<<UTMI_TX_AMP_SHIFT);
+
+ /* UTMI_RX */
+ u2o_clear(base, UTMI_RX, UTMI_RX_SQ_THRESH_MASK
+ | UTMI_REG_SQ_LENGTH_MASK);
+ u2o_set(base, UTMI_RX, 7<<UTMI_RX_SQ_THRESH_SHIFT
+ | 2<<UTMI_REG_SQ_LENGTH_SHIFT);
+
+ /* UTMI_IVREF */
+ if (cpu_is_pxa168())
+ /* fixing Microsoft Altair board interface with NEC hub issue -
+ * Set UTMI_IVREF from 0x4a3 to 0x4bf */
+ u2o_write(base, UTMI_IVREF, 0x4bf);
+
+ /* toggle VCOCAL_START bit of UTMI_PLL */
+ udelay(200);
+ u2o_set(base, UTMI_PLL, VCOCAL_START);
+ udelay(40);
+ u2o_clear(base, UTMI_PLL, VCOCAL_START);
+
+ /* toggle REG_RCAL_START bit of UTMI_TX */
+ udelay(400);
+ u2o_set(base, UTMI_TX, REG_RCAL_START);
+ udelay(40);
+ u2o_clear(base, UTMI_TX, REG_RCAL_START);
+ udelay(400);
+
+ /* Make sure PHY PLL is ready */
+ loops = 0;
+ while ((u2o_get(base, UTMI_PLL) & PLL_READY) == 0) {
+ mdelay(1);
+ loops++;
+ if (loops > 100) {
+ printk(KERN_WARNING "calibrate timeout, UTMI_PLL %x\n",
+ u2o_get(base, UTMI_PLL));
+ break;
+ }
+ }
+
+ if (cpu_is_pxa168()) {
+ u2o_set(base, UTMI_RESERVE, 1 << 5);
+ /* Turn on UTMI PHY OTG extension */
+ u2o_write(base, UTMI_OTG_ADDON, 1);
+ }
+
+ return 0;
+}
+
+static int usb_phy_deinit_internal(void __iomem *base)
+{
+ pr_info("Deinit usb phy!!!\n");
+
+ if (cpu_is_pxa168())
+ u2o_clear(base, UTMI_OTG_ADDON, UTMI_OTG_ADDON_OTG_ON);
+
+ u2o_clear(base, UTMI_CTRL, UTMI_CTRL_RXBUF_PDWN);
+ u2o_clear(base, UTMI_CTRL, UTMI_CTRL_TXBUF_PDWN);
+ u2o_clear(base, UTMI_CTRL, UTMI_CTRL_USB_CLK_EN);
+ u2o_clear(base, UTMI_CTRL, 1<<UTMI_CTRL_PWR_UP_SHIFT);
+ u2o_clear(base, UTMI_CTRL, 1<<UTMI_CTRL_PLL_PWR_UP_SHIFT);
+
+ return 0;
+}
+
+int pxa_usb_phy_init(void __iomem *phy_reg)
+{
+ mutex_lock(&phy_lock);
+ if (phy_init_cnt++ == 0)
+ usb_phy_init_internal(phy_reg);
+ mutex_unlock(&phy_lock);
+ return 0;
+}
+
+void pxa_usb_phy_deinit(void __iomem *phy_reg)
+{
+ WARN_ON(phy_init_cnt == 0);
+
+ mutex_lock(&phy_lock);
+ if (--phy_init_cnt == 0)
+ usb_phy_deinit_internal(phy_reg);
+ mutex_unlock(&phy_lock);
+}
+#endif
+#endif
+#endif
+
+#ifdef CONFIG_USB_SUPPORT
+static u64 usb_dma_mask = ~(u32)0;
+
+#ifdef CONFIG_USB_MV_UDC
+struct resource pxa168_u2o_resources[] = {
+ /* regbase */
+ [0] = {
+ .start = PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET,
+ .end = PXA168_U2O_REGBASE + USB_REG_RANGE,
+ .flags = IORESOURCE_MEM,
+ .name = "capregs",
+ },
+ /* phybase */
+ [1] = {
+ .start = PXA168_U2O_PHYBASE,
+ .end = PXA168_U2O_PHYBASE + USB_PHY_RANGE,
+ .flags = IORESOURCE_MEM,
+ .name = "phyregs",
+ },
+ [2] = {
+ .start = IRQ_PXA168_USB1,
+ .end = IRQ_PXA168_USB1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device pxa168_device_u2o = {
+ .name = "mv-udc",
+ .id = -1,
+ .resource = pxa168_u2o_resources,
+ .num_resources = ARRAY_SIZE(pxa168_u2o_resources),
+ .dev = {
+ .dma_mask = &usb_dma_mask,
+ .coherent_dma_mask = 0xffffffff,
+ }
+};
+#endif /* CONFIG_USB_MV_UDC */
+
+#ifdef CONFIG_USB_EHCI_MV_U2O
+struct resource pxa168_u2oehci_resources[] = {
+ /* regbase */
+ [0] = {
+ .start = PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET,
+ .end = PXA168_U2O_REGBASE + USB_REG_RANGE,
+ .flags = IORESOURCE_MEM,
+ .name = "capregs",
+ },
+ /* phybase */
+ [1] = {
+ .start = PXA168_U2O_PHYBASE,
+ .end = PXA168_U2O_PHYBASE + USB_PHY_RANGE,
+ .flags = IORESOURCE_MEM,
+ .name = "phyregs",
+ },
+ [2] = {
+ .start = IRQ_PXA168_USB1,
+ .end = IRQ_PXA168_USB1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device pxa168_device_u2oehci = {
+ .name = "pxa-u2oehci",
+ .id = -1,
+ .dev = {
+ .dma_mask = &usb_dma_mask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+
+ .num_resources = ARRAY_SIZE(pxa168_u2oehci_resources),
+ .resource = pxa168_u2oehci_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_MV_OTG)
+struct resource pxa168_u2ootg_resources[] = {
+ /* regbase */
+ [0] = {
+ .start = PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET,
+ .end = PXA168_U2O_REGBASE + USB_REG_RANGE,
+ .flags = IORESOURCE_MEM,
+ .name = "capregs",
+ },
+ /* phybase */
+ [1] = {
+ .start = PXA168_U2O_PHYBASE,
+ .end = PXA168_U2O_PHYBASE + USB_PHY_RANGE,
+ .flags = IORESOURCE_MEM,
+ .name = "phyregs",
+ },
+ [2] = {
+ .start = IRQ_PXA168_USB1,
+ .end = IRQ_PXA168_USB1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device pxa168_device_u2ootg = {
+ .name = "mv-otg",
+ .id = -1,
+ .dev = {
+ .dma_mask = &usb_dma_mask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+
+ .num_resources = ARRAY_SIZE(pxa168_u2ootg_resources),
+ .resource = pxa168_u2ootg_resources,
+};
+#endif /* CONFIG_USB_MV_OTG */
+
+#endif
diff --git a/arch/arm/mach-mmp/include/mach/devices.h b/arch/arm/mach-mmp/include/mach/devices.h
index d0ec7da..21217ef 100644
--- a/arch/arm/mach-mmp/include/mach/devices.h
+++ b/arch/arm/mach-mmp/include/mach/devices.h
@@ -50,4 +50,7 @@
}
extern int pxa_register_device(struct pxa_device_desc *, void *, size_t);
+extern int pxa_usb_phy_init(void __iomem *phy_reg);
+extern void pxa_usb_phy_deinit(void __iomem *phy_reg);
+
#endif /* __MACH_DEVICE_H */
diff --git a/arch/arm/mach-mmp/include/mach/pxa168.h b/arch/arm/mach-mmp/include/mach/pxa168.h
index dc03d58..09dcd6e 100644
--- a/arch/arm/mach-mmp/include/mach/pxa168.h
+++ b/arch/arm/mach-mmp/include/mach/pxa168.h
@@ -16,6 +16,7 @@
#include <plat/pxa27x_keypad.h>
#include <mach/cputype.h>
#include <linux/pxa168_eth.h>
+#include <linux/platform_data/mv_usb.h>
extern struct pxa_device_desc pxa168_device_uart1;
extern struct pxa_device_desc pxa168_device_uart2;
@@ -36,12 +37,9 @@
extern struct pxa_device_desc pxa168_device_keypad;
extern struct pxa_device_desc pxa168_device_eth;
-struct pxa168_usb_pdata {
- /* If NULL, default phy init routine for PXA168 would be called */
- int (*phy_init)(void __iomem *usb_phy_reg_base);
-};
/* pdata can be NULL */
-int __init pxa168_add_usb_host(struct pxa168_usb_pdata *pdata);
+extern int __init pxa168_add_usb_host(struct mv_usb_platform_data *pdata);
+
extern struct platform_device pxa168_device_gpio;
diff --git a/arch/arm/mach-mmp/include/mach/pxa910.h b/arch/arm/mach-mmp/include/mach/pxa910.h
index e2e1f1e..793634c 100644
--- a/arch/arm/mach-mmp/include/mach/pxa910.h
+++ b/arch/arm/mach-mmp/include/mach/pxa910.h
@@ -20,6 +20,9 @@
extern struct pxa_device_desc pxa910_device_pwm3;
extern struct pxa_device_desc pxa910_device_pwm4;
extern struct pxa_device_desc pxa910_device_nand;
+extern struct platform_device pxa168_device_u2o;
+extern struct platform_device pxa168_device_u2ootg;
+extern struct platform_device pxa168_device_u2oehci;
extern struct platform_device pxa910_device_gpio;
extern struct platform_device pxa910_device_rtc;
diff --git a/arch/arm/mach-mmp/include/mach/regs-usb.h b/arch/arm/mach-mmp/include/mach/regs-usb.h
new file mode 100644
index 0000000..b047bf4
--- /dev/null
+++ b/arch/arm/mach-mmp/include/mach/regs-usb.h
@@ -0,0 +1,253 @@
+/*
+ * Copyright (C) 2011 Marvell International Ltd. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __ASM_ARCH_REGS_USB_H
+#define __ASM_ARCH_REGS_USB_H
+
+#define PXA168_U2O_REGBASE (0xd4208000)
+#define PXA168_U2O_PHYBASE (0xd4207000)
+
+#define PXA168_U2H_REGBASE (0xd4209000)
+#define PXA168_U2H_PHYBASE (0xd4206000)
+
+#define MMP3_HSIC1_REGBASE (0xf0001000)
+#define MMP3_HSIC1_PHYBASE (0xf0001800)
+
+#define MMP3_HSIC2_REGBASE (0xf0002000)
+#define MMP3_HSIC2_PHYBASE (0xf0002800)
+
+#define MMP3_FSIC_REGBASE (0xf0003000)
+#define MMP3_FSIC_PHYBASE (0xf0003800)
+
+
+#define USB_REG_RANGE (0x1ff)
+#define USB_PHY_RANGE (0xff)
+
+/* registers */
+#define U2x_CAPREGS_OFFSET 0x100
+
+/* phy regs */
+#define UTMI_REVISION 0x0
+#define UTMI_CTRL 0x4
+#define UTMI_PLL 0x8
+#define UTMI_TX 0xc
+#define UTMI_RX 0x10
+#define UTMI_IVREF 0x14
+#define UTMI_T0 0x18
+#define UTMI_T1 0x1c
+#define UTMI_T2 0x20
+#define UTMI_T3 0x24
+#define UTMI_T4 0x28
+#define UTMI_T5 0x2c
+#define UTMI_RESERVE 0x30
+#define UTMI_USB_INT 0x34
+#define UTMI_DBG_CTL 0x38
+#define UTMI_OTG_ADDON 0x3c
+
+/* For UTMICTRL Register */
+#define UTMI_CTRL_USB_CLK_EN (1 << 31)
+/* pxa168 */
+#define UTMI_CTRL_SUSPEND_SET1 (1 << 30)
+#define UTMI_CTRL_SUSPEND_SET2 (1 << 29)
+#define UTMI_CTRL_RXBUF_PDWN (1 << 24)
+#define UTMI_CTRL_TXBUF_PDWN (1 << 11)
+
+#define UTMI_CTRL_INPKT_DELAY_SHIFT 30
+#define UTMI_CTRL_INPKT_DELAY_SOF_SHIFT 28
+#define UTMI_CTRL_PU_REF_SHIFT 20
+#define UTMI_CTRL_ARC_PULLDN_SHIFT 12
+#define UTMI_CTRL_PLL_PWR_UP_SHIFT 1
+#define UTMI_CTRL_PWR_UP_SHIFT 0
+
+/* For UTMI_PLL Register */
+#define UTMI_PLL_PLLCALI12_SHIFT 29
+#define UTMI_PLL_PLLCALI12_MASK (0x3 << 29)
+
+#define UTMI_PLL_PLLVDD18_SHIFT 27
+#define UTMI_PLL_PLLVDD18_MASK (0x3 << 27)
+
+#define UTMI_PLL_PLLVDD12_SHIFT 25
+#define UTMI_PLL_PLLVDD12_MASK (0x3 << 25)
+
+#define UTMI_PLL_CLK_BLK_EN_SHIFT 24
+#define CLK_BLK_EN (0x1 << 24)
+#define PLL_READY (0x1 << 23)
+#define KVCO_EXT (0x1 << 22)
+#define VCOCAL_START (0x1 << 21)
+
+#define UTMI_PLL_KVCO_SHIFT 15
+#define UTMI_PLL_KVCO_MASK (0x7 << 15)
+
+#define UTMI_PLL_ICP_SHIFT 12
+#define UTMI_PLL_ICP_MASK (0x7 << 12)
+
+#define UTMI_PLL_FBDIV_SHIFT 4
+#define UTMI_PLL_FBDIV_MASK (0xFF << 4)
+
+#define UTMI_PLL_REFDIV_SHIFT 0
+#define UTMI_PLL_REFDIV_MASK (0xF << 0)
+
+/* For UTMI_TX Register */
+#define UTMI_TX_REG_EXT_FS_RCAL_SHIFT 27
+#define UTMI_TX_REG_EXT_FS_RCAL_MASK (0xf << 27)
+
+#define UTMI_TX_REG_EXT_FS_RCAL_EN_SHIFT 26
+#define UTMI_TX_REG_EXT_FS_RCAL_EN_MASK (0x1 << 26)
+
+#define UTMI_TX_TXVDD12_SHIFT 22
+#define UTMI_TX_TXVDD12_MASK (0x3 << 22)
+
+#define UTMI_TX_CK60_PHSEL_SHIFT 17
+#define UTMI_TX_CK60_PHSEL_MASK (0xf << 17)
+
+#define UTMI_TX_IMPCAL_VTH_SHIFT 14
+#define UTMI_TX_IMPCAL_VTH_MASK (0x7 << 14)
+
+#define REG_RCAL_START (0x1 << 12)
+
+#define UTMI_TX_LOW_VDD_EN_SHIFT 11
+
+#define UTMI_TX_AMP_SHIFT 0
+#define UTMI_TX_AMP_MASK (0x7 << 0)
+
+/* For UTMI_RX Register */
+#define UTMI_REG_SQ_LENGTH_SHIFT 15
+#define UTMI_REG_SQ_LENGTH_MASK (0x3 << 15)
+
+#define UTMI_RX_SQ_THRESH_SHIFT 4
+#define UTMI_RX_SQ_THRESH_MASK (0xf << 4)
+
+#define UTMI_OTG_ADDON_OTG_ON (1 << 0)
+
+/* For MMP3 USB Phy */
+#define USB2_PLL_REG0 0x4
+#define USB2_PLL_REG1 0x8
+#define USB2_TX_REG0 0x10
+#define USB2_TX_REG1 0x14
+#define USB2_TX_REG2 0x18
+#define USB2_RX_REG0 0x20
+#define USB2_RX_REG1 0x24
+#define USB2_RX_REG2 0x28
+#define USB2_ANA_REG0 0x30
+#define USB2_ANA_REG1 0x34
+#define USB2_ANA_REG2 0x38
+#define USB2_DIG_REG0 0x3C
+#define USB2_DIG_REG1 0x40
+#define USB2_DIG_REG2 0x44
+#define USB2_DIG_REG3 0x48
+#define USB2_TEST_REG0 0x4C
+#define USB2_TEST_REG1 0x50
+#define USB2_TEST_REG2 0x54
+#define USB2_CHARGER_REG0 0x58
+#define USB2_OTG_REG0 0x5C
+#define USB2_PHY_MON0 0x60
+#define USB2_RESETVE_REG0 0x64
+#define USB2_ICID_REG0 0x78
+#define USB2_ICID_REG1 0x7C
+
+/* USB2_PLL_REG0 */
+/* This is for Ax stepping */
+#define USB2_PLL_FBDIV_SHIFT_MMP3 0
+#define USB2_PLL_FBDIV_MASK_MMP3 (0xFF << 0)
+
+#define USB2_PLL_REFDIV_SHIFT_MMP3 8
+#define USB2_PLL_REFDIV_MASK_MMP3 (0xF << 8)
+
+#define USB2_PLL_VDD12_SHIFT_MMP3 12
+#define USB2_PLL_VDD18_SHIFT_MMP3 14
+
+/* This is for B0 stepping */
+#define USB2_PLL_FBDIV_SHIFT_MMP3_B0 0
+#define USB2_PLL_REFDIV_SHIFT_MMP3_B0 9
+#define USB2_PLL_VDD18_SHIFT_MMP3_B0 14
+#define USB2_PLL_FBDIV_MASK_MMP3_B0 0x01FF
+#define USB2_PLL_REFDIV_MASK_MMP3_B0 0x3E00
+
+#define USB2_PLL_CAL12_SHIFT_MMP3 0
+#define USB2_PLL_CALI12_MASK_MMP3 (0x3 << 0)
+
+#define USB2_PLL_VCOCAL_START_SHIFT_MMP3 2
+
+#define USB2_PLL_KVCO_SHIFT_MMP3 4
+#define USB2_PLL_KVCO_MASK_MMP3 (0x7<<4)
+
+#define USB2_PLL_ICP_SHIFT_MMP3 8
+#define USB2_PLL_ICP_MASK_MMP3 (0x7<<8)
+
+#define USB2_PLL_LOCK_BYPASS_SHIFT_MMP3 12
+
+#define USB2_PLL_PU_PLL_SHIFT_MMP3 13
+#define USB2_PLL_PU_PLL_MASK (0x1 << 13)
+
+#define USB2_PLL_READY_MASK_MMP3 (0x1 << 15)
+
+/* USB2_TX_REG0 */
+#define USB2_TX_IMPCAL_VTH_SHIFT_MMP3 8
+#define USB2_TX_IMPCAL_VTH_MASK_MMP3 (0x7 << 8)
+
+#define USB2_TX_RCAL_START_SHIFT_MMP3 13
+
+/* USB2_TX_REG1 */
+#define USB2_TX_CK60_PHSEL_SHIFT_MMP3 0
+#define USB2_TX_CK60_PHSEL_MASK_MMP3 (0xf << 0)
+
+#define USB2_TX_AMP_SHIFT_MMP3 4
+#define USB2_TX_AMP_MASK_MMP3 (0x7 << 4)
+
+#define USB2_TX_VDD12_SHIFT_MMP3 8
+#define USB2_TX_VDD12_MASK_MMP3 (0x3 << 8)
+
+/* USB2_TX_REG2 */
+#define USB2_TX_DRV_SLEWRATE_SHIFT 10
+
+/* USB2_RX_REG0 */
+#define USB2_RX_SQ_THRESH_SHIFT_MMP3 4
+#define USB2_RX_SQ_THRESH_MASK_MMP3 (0xf << 4)
+
+#define USB2_RX_SQ_LENGTH_SHIFT_MMP3 10
+#define USB2_RX_SQ_LENGTH_MASK_MMP3 (0x3 << 10)
+
+/* USB2_ANA_REG1*/
+#define USB2_ANA_PU_ANA_SHIFT_MMP3 14
+
+/* USB2_OTG_REG0 */
+#define USB2_OTG_PU_OTG_SHIFT_MMP3 3
+
+/* fsic registers */
+#define FSIC_MISC 0x4
+#define FSIC_INT 0x28
+#define FSIC_CTRL 0x30
+
+/* HSIC registers */
+#define HSIC_PAD_CTRL 0x4
+
+#define HSIC_CTRL 0x8
+#define HSIC_CTRL_HSIC_ENABLE (1<<7)
+#define HSIC_CTRL_PLL_BYPASS (1<<4)
+
+#define TEST_GRP_0 0xc
+#define TEST_GRP_1 0x10
+
+#define HSIC_INT 0x14
+#define HSIC_INT_READY_INT_EN (1<<10)
+#define HSIC_INT_CONNECT_INT_EN (1<<9)
+#define HSIC_INT_CORE_INT_EN (1<<8)
+#define HSIC_INT_HS_READY (1<<2)
+#define HSIC_INT_CONNECT (1<<1)
+#define HSIC_INT_CORE (1<<0)
+
+#define HSIC_CONFIG 0x18
+#define USBHSIC_CTRL 0x20
+
+#define HSIC_USB_CTRL 0x28
+#define HSIC_USB_CTRL_CLKEN 1
+#define HSIC_USB_CLK_PHY 0x0
+#define HSIC_USB_CLK_PMU 0x1
+
+#endif /* __ASM_ARCH_PXA_U2O_H */
diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c
index b24d2c3..62d787c 100644
--- a/arch/arm/mach-mmp/pxa168.c
+++ b/arch/arm/mach-mmp/pxa168.c
@@ -14,6 +14,7 @@
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/platform_device.h>
+#include <linux/platform_data/mv_usb.h>
#include <asm/mach/time.h>
#include <asm/system_misc.h>
@@ -27,6 +28,7 @@
#include <mach/mfp.h>
#include <linux/dma-mapping.h>
#include <mach/pxa168.h>
+#include <mach/regs-usb.h>
#include "common.h"
#include "clock.h"
@@ -93,7 +95,7 @@
INIT_CLKREG(&clk_gpio, "pxa-gpio", NULL),
INIT_CLKREG(&clk_keypad, "pxa27x-keypad", NULL),
INIT_CLKREG(&clk_eth, "pxa168-eth", "MFUCLK"),
- INIT_CLKREG(&clk_usb, "pxa168-ehci", "PXA168-USBCLK"),
+ INIT_CLKREG(&clk_usb, NULL, "PXA168-USBCLK"),
INIT_CLKREG(&clk_rtc, "sa1100-rtc", NULL),
};
@@ -184,17 +186,17 @@
struct resource pxa168_usb_host_resources[] = {
/* USB Host conroller register base */
[0] = {
- .start = 0xd4209000,
- .end = 0xd4209000 + 0x200,
+ .start = PXA168_U2H_REGBASE + U2x_CAPREGS_OFFSET,
+ .end = PXA168_U2H_REGBASE + USB_REG_RANGE,
.flags = IORESOURCE_MEM,
- .name = "pxa168-usb-host",
+ .name = "capregs",
},
/* USB PHY register base */
[1] = {
- .start = 0xd4206000,
- .end = 0xd4206000 + 0xff,
+ .start = PXA168_U2H_PHYBASE,
+ .end = PXA168_U2H_PHYBASE + USB_PHY_RANGE,
.flags = IORESOURCE_MEM,
- .name = "pxa168-usb-phy",
+ .name = "phyregs",
},
[2] = {
.start = IRQ_PXA168_USB2,
@@ -205,7 +207,7 @@
static u64 pxa168_usb_host_dmamask = DMA_BIT_MASK(32);
struct platform_device pxa168_device_usb_host = {
- .name = "pxa168-ehci",
+ .name = "pxa-sph",
.id = -1,
.dev = {
.dma_mask = &pxa168_usb_host_dmamask,
@@ -216,7 +218,7 @@
.resource = pxa168_usb_host_resources,
};
-int __init pxa168_add_usb_host(struct pxa168_usb_pdata *pdata)
+int __init pxa168_add_usb_host(struct mv_usb_platform_data *pdata)
{
pxa168_device_usb_host.dev.platform_data = pdata;
return platform_device_register(&pxa168_device_usb_host);
diff --git a/arch/arm/mach-mmp/pxa910.c b/arch/arm/mach-mmp/pxa910.c
index 43f8bcc..6da52e9 100644
--- a/arch/arm/mach-mmp/pxa910.c
+++ b/arch/arm/mach-mmp/pxa910.c
@@ -109,7 +109,7 @@
INIT_CLKREG(&clk_pwm4, "pxa910-pwm.3", NULL),
INIT_CLKREG(&clk_nand, "pxa3xx-nand", NULL),
INIT_CLKREG(&clk_gpio, "pxa-gpio", NULL),
- INIT_CLKREG(&clk_u2o, "pxa-u2o", "U2OCLK"),
+ INIT_CLKREG(&clk_u2o, NULL, "U2OCLK"),
INIT_CLKREG(&clk_rtc, "sa1100-rtc", NULL),
};
diff --git a/arch/arm/mach-mmp/ttc_dkb.c b/arch/arm/mach-mmp/ttc_dkb.c
index 3fc9ed2..2662153 100644
--- a/arch/arm/mach-mmp/ttc_dkb.c
+++ b/arch/arm/mach-mmp/ttc_dkb.c
@@ -17,6 +17,7 @@
#include <linux/interrupt.h>
#include <linux/i2c/pca953x.h>
#include <linux/gpio.h>
+#include <linux/platform_data/mv_usb.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -25,6 +26,7 @@
#include <mach/mfp-pxa910.h>
#include <mach/pxa910.h>
#include <mach/irqs.h>
+#include <mach/regs-usb.h>
#include "common.h"
@@ -144,6 +146,26 @@
},
};
+#ifdef CONFIG_USB_SUPPORT
+#if defined(CONFIG_USB_MV_UDC) || defined(CONFIG_USB_EHCI_MV_U2O)
+
+static char *pxa910_usb_clock_name[] = {
+ [0] = "U2OCLK",
+};
+
+static struct mv_usb_platform_data ttc_usb_pdata = {
+ .clknum = 1,
+ .clkname = pxa910_usb_clock_name,
+ .vbus = NULL,
+ .mode = MV_USB_MODE_OTG,
+ .otg_force_a_bus_req = 1,
+ .phy_init = pxa_usb_phy_init,
+ .phy_deinit = pxa_usb_phy_deinit,
+ .set_vbus = NULL,
+};
+#endif
+#endif
+
static void __init ttc_dkb_init(void)
{
mfp_config(ARRAY_AND_SIZE(ttc_dkb_pin_config));
@@ -154,6 +176,21 @@
/* off-chip devices */
pxa910_add_twsi(0, NULL, ARRAY_AND_SIZE(ttc_dkb_i2c_info));
platform_add_devices(ARRAY_AND_SIZE(ttc_dkb_devices));
+
+#ifdef CONFIG_USB_MV_UDC
+ pxa168_device_u2o.dev.platform_data = &ttc_usb_pdata;
+ platform_device_register(&pxa168_device_u2o);
+#endif
+
+#ifdef CONFIG_USB_EHCI_MV_U2O
+ pxa168_device_u2oehci.dev.platform_data = &ttc_usb_pdata;
+ platform_device_register(&pxa168_device_u2oehci);
+#endif
+
+#ifdef CONFIG_USB_MV_OTG
+ pxa168_device_u2ootg.dev.platform_data = &ttc_usb_pdata;
+ platform_device_register(&pxa168_device_u2ootg);
+#endif
}
MACHINE_START(TTC_DKB, "PXA910-based TTC_DKB Development Platform")
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index b83b95a..6bd692d 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -102,6 +102,10 @@
GPIO44_BTUART_CTS,
GPIO45_BTUART_RTS_LPM_LOW,
+ /* STUART (IRDA) */
+ GPIO46_STUART_RXD,
+ GPIO47_STUART_TXD,
+
/* PWM 1 (Backlight) */
GPIO17_PWM1_OUT,
@@ -125,7 +129,7 @@
GPIO88_GPIO,
/* HX4700 specific input GPIOs */
- GPIO12_GPIO, /* ASIC3_IRQ */
+ GPIO12_GPIO | WAKEUP_ON_EDGE_RISE, /* ASIC3_IRQ */
GPIO13_GPIO, /* W3220_IRQ */
GPIO14_GPIO, /* nWLAN_IRQ */
@@ -227,7 +231,6 @@
ASIC3_GPIOC0_LED0, /* red */
ASIC3_GPIOC1_LED1, /* green */
ASIC3_GPIOC2_LED2, /* blue */
- ASIC3_GPIOC4_CF_nCD,
ASIC3_GPIOC5_nCIOW,
ASIC3_GPIOC6_nCIOR,
ASIC3_GPIOC7_nPCE_1,
@@ -241,6 +244,7 @@
ASIC3_GPIOC15_nPIOR,
/* GPIOD: input GPIOs, CF */
+ ASIC3_GPIOD4_CF_nCD,
ASIC3_GPIOD11_nCIOIS16,
ASIC3_GPIOD12_nCWAIT,
ASIC3_GPIOD15_nPIOW,
@@ -291,6 +295,7 @@
.gpio_config_num = ARRAY_SIZE(asic3_gpio_config),
.irq_base = IRQ_BOARD_START,
.gpio_base = HX4700_ASIC3_GPIO_BASE,
+ .clock_rate = 4000000,
.leds = asic3_leds,
};
@@ -859,6 +864,7 @@
int ret;
pxa2xx_mfp_config(ARRAY_AND_SIZE(hx4700_pin_config));
+ gpio_set_wake(GPIO12_HX4700_ASIC3_IRQ, 1);
ret = gpio_request_array(ARRAY_AND_SIZE(global_gpios));
if (ret)
pr_err ("hx4700: Failed to request GPIOs.\n");
diff --git a/arch/arm/mach-pxa/include/mach/mioa701.h b/arch/arm/mach-pxa/include/mach/mioa701.h
index 0286844..e57f5c7 100644
--- a/arch/arm/mach-pxa/include/mach/mioa701.h
+++ b/arch/arm/mach-pxa/include/mach/mioa701.h
@@ -61,6 +61,9 @@
#define GPIO93_KEY_VOLUME_UP 93
#define GPIO94_KEY_VOLUME_DOWN 94
+/* Camera */
+#define GPIO56_MT9M111_nOE 56
+
extern struct input_dev *mioa701_evdev;
extern void mioa701_gpio_lpm_set(unsigned long mfp_pin);
diff --git a/arch/arm/mach-pxa/include/mach/pcm990_baseboard.h b/arch/arm/mach-pxa/include/mach/pcm990_baseboard.h
index d727916..0260aaa 100644
--- a/arch/arm/mach-pxa/include/mach/pcm990_baseboard.h
+++ b/arch/arm/mach-pxa/include/mach/pcm990_baseboard.h
@@ -31,7 +31,6 @@
#define PCM990_CTRL_INT_IRQ PXA_GPIO_TO_IRQ(PCM990_CTRL_INT_IRQ_GPIO)
#define PCM990_CTRL_INT_IRQ_EDGE IRQ_TYPE_EDGE_RISING
#define PCM990_CTRL_PHYS PXA_CS1_PHYS /* 16-Bit */
-#define PCM990_CTRL_BASE 0xea000000
#define PCM990_CTRL_SIZE (1*1024*1024)
#define PCM990_CTRL_PWR_IRQ_GPIO 14
@@ -69,13 +68,13 @@
#define PCM990_CTRL_MMC2DE 0x0004 /* R MMC2 Card detect */
#define PCM990_CTRL_MMC2WP 0x0008 /* R MMC2 Card write protect */
-#define PCM990_CTRL_REG6 0x000C /* Interrupt Clear REGISTER */
+#define PCM990_CTRL_INTSETCLR 0x000C /* Interrupt Clear REGISTER */
#define PCM990_CTRL_INTC0 0x0001 /* Clear Reg BT Detect */
#define PCM990_CTRL_INTC1 0x0002 /* Clear Reg FR RI */
#define PCM990_CTRL_INTC2 0x0004 /* Clear Reg MMC1 Detect */
#define PCM990_CTRL_INTC3 0x0008 /* Clear Reg PM_5V off */
-#define PCM990_CTRL_REG7 0x000E /* Interrupt Enable REGISTER */
+#define PCM990_CTRL_INTMSKENA 0x000E /* Interrupt Enable REGISTER */
#define PCM990_CTRL_ENAINT0 0x0001 /* Enable Int BT Detect */
#define PCM990_CTRL_ENAINT1 0x0002 /* Enable Int FR RI */
#define PCM990_CTRL_ENAINT2 0x0004 /* Enable Int MMC1 Detect */
@@ -102,32 +101,6 @@
#define PCM990_CTRL_ACPRES 0x0004 /* DC Present */
#define PCM990_CTRL_ACALARM 0x0008 /* Error Akku */
-#define PCM990_CTRL_P2V(x) ((x) - PCM990_CTRL_PHYS + PCM990_CTRL_BASE)
-#define PCM990_CTRL_V2P(x) ((x) - PCM990_CTRL_BASE + PCM990_CTRL_PHYS)
-
-#ifndef __ASSEMBLY__
-# define __PCM990_CTRL_REG(x) \
- (*((volatile unsigned char *)PCM990_CTRL_P2V(x)))
-#else
-# define __PCM990_CTRL_REG(x) PCM990_CTRL_P2V(x)
-#endif
-
-#define PCM990_INTMSKENA __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG7)
-#define PCM990_INTSETCLR __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG6)
-#define PCM990_CTRL0 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG0)
-#define PCM990_CTRL1 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG1)
-#define PCM990_CTRL2 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG2)
-#define PCM990_CTRL3 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3)
-#define PCM990_CTRL4 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG4)
-#define PCM990_CTRL5 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5)
-#define PCM990_CTRL6 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG6)
-#define PCM990_CTRL7 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG7)
-#define PCM990_CTRL8 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG8)
-#define PCM990_CTRL9 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG9)
-#define PCM990_CTRL10 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG10)
-#define PCM990_CTRL11 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG11)
-
-
/*
* IDE
*/
@@ -166,24 +139,6 @@
#define PCM990_IDE_PLD_P2V(x) ((x) - PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_BASE)
#define PCM990_IDE_PLD_V2P(x) ((x) - PCM990_IDE_PLD_BASE + PCM990_IDE_PLD_PHYS)
-#ifndef __ASSEMBLY__
-# define __PCM990_IDE_PLD_REG(x) \
- (*((volatile unsigned char *)PCM990_IDE_PLD_P2V(x)))
-#else
-# define __PCM990_IDE_PLD_REG(x) PCM990_IDE_PLD_P2V(x)
-#endif
-
-#define PCM990_IDE0 \
- __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG0)
-#define PCM990_IDE1 \
- __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG1)
-#define PCM990_IDE2 \
- __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG2)
-#define PCM990_IDE3 \
- __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG3)
-#define PCM990_IDE4 \
- __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG4)
-
/*
* Compact Flash
*/
@@ -196,10 +151,6 @@
#define PCM990_CF_CD_EDGE IRQ_TYPE_EDGE_RISING
#define PCM990_CF_PLD_PHYS 0x30000000 /* 16 bit wide */
-#define PCM990_CF_PLD_BASE 0xef000000
-#define PCM990_CF_PLD_SIZE (1*1024*1024)
-#define PCM990_CF_PLD_P2V(x) ((x) - PCM990_CF_PLD_PHYS + PCM990_CF_PLD_BASE)
-#define PCM990_CF_PLD_V2P(x) ((x) - PCM990_CF_PLD_BASE + PCM990_CF_PLD_PHYS)
/* visible CPLD (U6) registers */
#define PCM990_CF_PLD_REG0 0x1000 /* OFFSET CF REGISTER 0 */
@@ -239,21 +190,6 @@
#define PCM990_CF_REG6_CD1 0x0001 /* R CF Card_Detect1 */
#define PCM990_CF_REG6_CD2 0x0002 /* R CF Card_Detect2 */
-#ifndef __ASSEMBLY__
-# define __PCM990_CF_PLD_REG(x) \
- (*((volatile unsigned char *)PCM990_CF_PLD_P2V(x)))
-#else
-# define __PCM990_CF_PLD_REG(x) PCM990_CF_PLD_P2V(x)
-#endif
-
-#define PCM990_CF0 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG0)
-#define PCM990_CF1 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG1)
-#define PCM990_CF2 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG2)
-#define PCM990_CF3 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG3)
-#define PCM990_CF4 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG4)
-#define PCM990_CF5 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG5)
-#define PCM990_CF6 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG6)
-
/*
* Wolfson AC97 Touch
*/
diff --git a/arch/arm/mach-pxa/mioa701.c b/arch/arm/mach-pxa/mioa701.c
index 061d570..929c62b 100644
--- a/arch/arm/mach-pxa/mioa701.c
+++ b/arch/arm/mach-pxa/mioa701.c
@@ -103,6 +103,7 @@
GPIO82_CIF_DD_5,
GPIO84_CIF_FV,
GPIO85_CIF_LV,
+ MIO_CFG_OUT(GPIO56_MT9M111_nOE, AF0, DRIVE_LOW),
/* Bluetooth */
MIO_CFG_IN(GPIO14_BT_nACTIVITY, AF0),
@@ -705,6 +706,7 @@
{ GPIO9_CHARGE_EN, GPIOF_OUT_INIT_HIGH, "Charger enable" },
{ GPIO18_POWEROFF, GPIOF_OUT_INIT_LOW, "Power Off" },
{ GPIO87_LCD_POWER, GPIOF_OUT_INIT_LOW, "LCD Power" },
+ { GPIO56_MT9M111_nOE, GPIOF_OUT_INIT_LOW, "Camera nOE" },
};
static void __init mioa701_machine_init(void)
diff --git a/arch/arm/mach-pxa/pcm990-baseboard.c b/arch/arm/mach-pxa/pcm990-baseboard.c
index abab4e2..cb723e8 100644
--- a/arch/arm/mach-pxa/pcm990-baseboard.c
+++ b/arch/arm/mach-pxa/pcm990-baseboard.c
@@ -65,6 +65,18 @@
GPIO31_AC97_SYNC,
};
+static void __iomem *pcm990_cpld_base;
+
+static u8 pcm990_cpld_readb(unsigned int reg)
+{
+ return readb(pcm990_cpld_base + reg);
+}
+
+static void pcm990_cpld_writeb(u8 value, unsigned int reg)
+{
+ writeb(value, pcm990_cpld_base + reg);
+}
+
/*
* pcm990_lcd_power - control power supply to the LCD
* @on: 0 = switch off, 1 = switch on
@@ -78,13 +90,13 @@
/* enable LCD-Latches
* power on LCD
*/
- __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) =
- PCM990_CTRL_LCDPWR + PCM990_CTRL_LCDON;
+ pcm990_cpld_writeb(PCM990_CTRL_LCDPWR + PCM990_CTRL_LCDON,
+ PCM990_CTRL_REG3);
} else {
/* disable LCD-Latches
* power off LCD
*/
- __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) = 0x00;
+ pcm990_cpld_writeb(0, PCM990_CTRL_REG3);
}
}
#endif
@@ -243,15 +255,26 @@
static void pcm990_mask_ack_irq(struct irq_data *d)
{
int pcm990_irq = (d->irq - PCM027_IRQ(0));
- PCM990_INTMSKENA = (pcm990_irq_enabled &= ~(1 << pcm990_irq));
+
+ pcm990_irq_enabled &= ~(1 << pcm990_irq);
+
+ pcm990_cpld_writeb(pcm990_irq_enabled, PCM990_CTRL_INTMSKENA);
}
static void pcm990_unmask_irq(struct irq_data *d)
{
int pcm990_irq = (d->irq - PCM027_IRQ(0));
+ u8 val;
+
/* the irq can be acknowledged only if deasserted, so it's done here */
- PCM990_INTSETCLR |= 1 << pcm990_irq;
- PCM990_INTMSKENA = (pcm990_irq_enabled |= (1 << pcm990_irq));
+
+ pcm990_irq_enabled |= (1 << pcm990_irq);
+
+ val = pcm990_cpld_readb(PCM990_CTRL_INTSETCLR);
+ val |= 1 << pcm990_irq;
+ pcm990_cpld_writeb(val, PCM990_CTRL_INTSETCLR);
+
+ pcm990_cpld_writeb(pcm990_irq_enabled, PCM990_CTRL_INTMSKENA);
}
static struct irq_chip pcm990_irq_chip = {
@@ -261,7 +284,10 @@
static void pcm990_irq_handler(unsigned int irq, struct irq_desc *desc)
{
- unsigned long pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled;
+ unsigned long pending;
+
+ pending = ~pcm990_cpld_readb(PCM990_CTRL_INTSETCLR);
+ pending &= pcm990_irq_enabled;
do {
/* clear our parent IRQ */
@@ -270,7 +296,8 @@
irq = PCM027_IRQ(0) + __ffs(pending);
generic_handle_irq(irq);
}
- pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled;
+ pending = ~pcm990_cpld_readb(PCM990_CTRL_INTSETCLR);
+ pending &= pcm990_irq_enabled;
} while (pending);
}
@@ -285,8 +312,9 @@
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
}
- PCM990_INTMSKENA = 0x00; /* disable all Interrupts */
- PCM990_INTSETCLR = 0xFF;
+ /* disable all Interrupts */
+ pcm990_cpld_writeb(0x0, PCM990_CTRL_INTMSKENA);
+ pcm990_cpld_writeb(0xff, PCM990_CTRL_INTSETCLR);
irq_set_chained_handler(PCM990_CTRL_INT_IRQ, pcm990_irq_handler);
irq_set_irq_type(PCM990_CTRL_INT_IRQ, PCM990_CTRL_INT_IRQ_EDGE);
@@ -309,13 +337,16 @@
static void pcm990_mci_setpower(struct device *dev, unsigned int vdd)
{
struct pxamci_platform_data *p_d = dev->platform_data;
+ u8 val;
+
+ val = pcm990_cpld_readb(PCM990_CTRL_REG5);
if ((1 << vdd) & p_d->ocr_mask)
- __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5) =
- PCM990_CTRL_MMC2PWR;
+ val |= PCM990_CTRL_MMC2PWR;
else
- __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5) =
- ~PCM990_CTRL_MMC2PWR;
+ val &= ~PCM990_CTRL_MMC2PWR;
+
+ pcm990_cpld_writeb(PCM990_CTRL_MMC2PWR, PCM990_CTRL_REG5);
}
static void pcm990_mci_exit(struct device *dev, void *data)
@@ -481,23 +512,6 @@
#endif /* CONFIG_VIDEO_PXA27x ||CONFIG_VIDEO_PXA27x_MODULE */
/*
- * enable generic access to the base board control CPLDs U6 and U7
- */
-static struct map_desc pcm990_io_desc[] __initdata = {
- {
- .virtual = PCM990_CTRL_BASE,
- .pfn = __phys_to_pfn(PCM990_CTRL_PHYS),
- .length = PCM990_CTRL_SIZE,
- .type = MT_DEVICE /* CPLD */
- }, {
- .virtual = PCM990_CF_PLD_BASE,
- .pfn = __phys_to_pfn(PCM990_CF_PLD_PHYS),
- .length = PCM990_CF_PLD_SIZE,
- .type = MT_DEVICE /* CPLD */
- }
-};
-
-/*
* system init for baseboard usage. Will be called by pcm027 init.
*
* Add platform devices present on this baseboard and init
@@ -507,8 +521,11 @@
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(pcm990_pin_config));
- /* register CPLD access */
- iotable_init(ARRAY_AND_SIZE(pcm990_io_desc));
+ pcm990_cpld_base = ioremap(PCM990_CTRL_PHYS, PCM990_CTRL_SIZE);
+ if (!pcm990_cpld_base) {
+ pr_err("pcm990: failed to ioremap cpld\n");
+ return;
+ }
/* register CPLD's IRQ controller */
pcm990_init_irq();
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index bba3ab2..8fd255f 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -217,7 +217,7 @@
|| MACH_ARMCORE || ARCH_PXA_PALM || TRIZEPS_PCMCIA \
|| ARCOM_PCMCIA || ARCH_PXA_ESERIES || MACH_STARGATE2 \
|| MACH_VPAC270 || MACH_BALLOON3 || MACH_COLIBRI \
- || MACH_COLIBRI320)
+ || MACH_COLIBRI320 || MACH_H4700)
select PCMCIA_SA1111 if ARCH_LUBBOCK && SA1111
select PCMCIA_SOC_COMMON
help
diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile
index 47525de..7745b51 100644
--- a/drivers/pcmcia/Makefile
+++ b/drivers/pcmcia/Makefile
@@ -69,6 +69,7 @@
pxa2xx-obj-$(CONFIG_MACH_BALLOON3) += pxa2xx_balloon3.o
pxa2xx-obj-$(CONFIG_MACH_COLIBRI) += pxa2xx_colibri.o
pxa2xx-obj-$(CONFIG_MACH_COLIBRI320) += pxa2xx_colibri.o
+pxa2xx-obj-$(CONFIG_MACH_H4700) += pxa2xx_hx4700.o
obj-$(CONFIG_PCMCIA_PXA2XX) += pxa2xx_base.o $(pxa2xx-obj-y)
diff --git a/drivers/pcmcia/pxa2xx_hx4700.c b/drivers/pcmcia/pxa2xx_hx4700.c
new file mode 100644
index 0000000..7dfef3e
--- /dev/null
+++ b/drivers/pcmcia/pxa2xx_hx4700.c
@@ -0,0 +1,121 @@
+/*
+ * Copyright (C) 2012 Paul Parsons <lost.distance@yahoo.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <mach/hx4700.h>
+
+#include "soc_common.h"
+
+static struct gpio gpios[] = {
+ { GPIO114_HX4700_CF_RESET, GPIOF_OUT_INIT_LOW, "CF reset" },
+ { EGPIO4_CF_3V3_ON, GPIOF_OUT_INIT_LOW, "CF 3.3V enable" },
+};
+
+static int hx4700_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+ int ret;
+
+ ret = gpio_request_array(gpios, ARRAY_SIZE(gpios));
+ if (ret)
+ goto out;
+
+ /*
+ * IRQ type must be set before soc_pcmcia_hw_init() calls request_irq().
+ * The asic3 default IRQ type is level trigger low level detect, exactly
+ * the the signal present on GPIOD4_CF_nCD when a CF card is inserted.
+ * If the IRQ type is not changed, the asic3 interrupt handler will loop
+ * repeatedly because it is unable to clear the level trigger interrupt.
+ */
+ irq_set_irq_type(gpio_to_irq(GPIOD4_CF_nCD), IRQ_TYPE_EDGE_BOTH);
+
+ skt->stat[SOC_STAT_CD].gpio = GPIOD4_CF_nCD;
+ skt->stat[SOC_STAT_CD].name = "PCMCIA CD";
+ skt->stat[SOC_STAT_RDY].gpio = GPIO60_HX4700_CF_RNB;
+ skt->stat[SOC_STAT_RDY].name = "PCMCIA Ready";
+
+out:
+ return ret;
+}
+
+static void hx4700_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+ gpio_free_array(gpios, ARRAY_SIZE(gpios));
+}
+
+static void hx4700_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+ struct pcmcia_state *state)
+{
+ state->vs_3v = 1;
+ state->vs_Xv = 0;
+}
+
+static int hx4700_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+ const socket_state_t *state)
+{
+ switch (state->Vcc) {
+ case 0:
+ gpio_set_value(EGPIO4_CF_3V3_ON, 0);
+ break;
+ case 33:
+ gpio_set_value(EGPIO4_CF_3V3_ON, 1);
+ break;
+ default:
+ printk(KERN_ERR "pcmcia: Unsupported Vcc: %d\n", state->Vcc);
+ return -EINVAL;
+ }
+
+ gpio_set_value(GPIO114_HX4700_CF_RESET, (state->flags & SS_RESET) != 0);
+
+ return 0;
+}
+
+static struct pcmcia_low_level hx4700_pcmcia_ops = {
+ .owner = THIS_MODULE,
+ .nr = 1,
+ .hw_init = hx4700_pcmcia_hw_init,
+ .hw_shutdown = hx4700_pcmcia_hw_shutdown,
+ .socket_state = hx4700_pcmcia_socket_state,
+ .configure_socket = hx4700_pcmcia_configure_socket,
+};
+
+static struct platform_device *hx4700_pcmcia_device;
+
+static int __init hx4700_pcmcia_init(void)
+{
+ struct platform_device *pdev;
+
+ if (!machine_is_h4700())
+ return -ENODEV;
+
+ pdev = platform_device_register_data(NULL, "pxa2xx-pcmcia", -1,
+ &hx4700_pcmcia_ops, sizeof(hx4700_pcmcia_ops));
+ if (IS_ERR(pdev))
+ return PTR_ERR(pdev);
+
+ hx4700_pcmcia_device = pdev;
+
+ return 0;
+}
+
+static void __exit hx4700_pcmcia_exit(void)
+{
+ platform_device_unregister(hx4700_pcmcia_device);
+}
+
+module_init(hx4700_pcmcia_init);
+module_exit(hx4700_pcmcia_exit);
+
+MODULE_AUTHOR("Paul Parsons <lost.distance@yahoo.com>");
+MODULE_DESCRIPTION("HP iPAQ hx4700 PCMCIA driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/asic3.h b/include/linux/mfd/asic3.h
index ed793b7..ef6faa5 100644
--- a/include/linux/mfd/asic3.h
+++ b/include/linux/mfd/asic3.h
@@ -138,6 +138,7 @@
#define ASIC3_GPIOC13_nPWAIT ASIC3_CONFIG_GPIO(45, 1, 1, 0)
#define ASIC3_GPIOC14_nPIOIS16 ASIC3_CONFIG_GPIO(46, 1, 1, 0)
#define ASIC3_GPIOC15_nPIOR ASIC3_CONFIG_GPIO(47, 1, 0, 0)
+#define ASIC3_GPIOD4_CF_nCD ASIC3_CONFIG_GPIO(52, 1, 0, 0)
#define ASIC3_GPIOD11_nCIOIS16 ASIC3_CONFIG_GPIO(59, 1, 0, 0)
#define ASIC3_GPIOD12_nCWAIT ASIC3_CONFIG_GPIO(60, 1, 0, 0)
#define ASIC3_GPIOD15_nPIOW ASIC3_CONFIG_GPIO(63, 1, 0, 0)