include/linux/mmc/sdhci.h - kernel/msm-4.19 - Gitiles

 /*
  *  linux/include/linux/mmc/sdhci.h - Secure Digital Host Controller Interface
  *
  *  Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or (at
  * your option) any later version.
  */
 #ifndef LINUX_MMC_SDHCI_H
 #define LINUX_MMC_SDHCI_H

 #include <linux/scatterlist.h>
 #include <linux/compiler.h>
 #include <linux/types.h>
 #include <linux/io.h>
 #include <linux/mmc/host.h>

 struct sdhci_host {
 	/* Data set by hardware interface driver */
 	const char *hw_name;	/* Hardware bus name */

 	unsigned int quirks;	/* Deviations from spec. */

 /* Controller doesn't honor resets unless we touch the clock register */
 #define SDHCI_QUIRK_CLOCK_BEFORE_RESET			(1<<0)
 /* Controller has bad caps bits, but really supports DMA */
 #define SDHCI_QUIRK_FORCE_DMA				(1<<1)
 /* Controller doesn't like to be reset when there is no card inserted. */
 #define SDHCI_QUIRK_NO_CARD_NO_RESET			(1<<2)
 /* Controller doesn't like clearing the power reg before a change */
 #define SDHCI_QUIRK_SINGLE_POWER_WRITE			(1<<3)
 /* Controller has flaky internal state so reset it on each ios change */
 #define SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS		(1<<4)
 /* Controller has an unusable DMA engine */
 #define SDHCI_QUIRK_BROKEN_DMA				(1<<5)
 /* Controller has an unusable ADMA engine */
 #define SDHCI_QUIRK_BROKEN_ADMA				(1<<6)
 /* Controller can only DMA from 32-bit aligned addresses */
 #define SDHCI_QUIRK_32BIT_DMA_ADDR			(1<<7)
 /* Controller can only DMA chunk sizes that are a multiple of 32 bits */
 #define SDHCI_QUIRK_32BIT_DMA_SIZE			(1<<8)
 /* Controller can only ADMA chunks that are a multiple of 32 bits */
 #define SDHCI_QUIRK_32BIT_ADMA_SIZE			(1<<9)
 /* Controller needs to be reset after each request to stay stable */
 #define SDHCI_QUIRK_RESET_AFTER_REQUEST			(1<<10)
 /* Controller needs voltage and power writes to happen separately */
 #define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER		(1<<11)
 /* Controller provides an incorrect timeout value for transfers */
 #define SDHCI_QUIRK_BROKEN_TIMEOUT_VAL			(1<<12)
 /* Controller has an issue with buffer bits for small transfers */
 #define SDHCI_QUIRK_BROKEN_SMALL_PIO			(1<<13)
 /* Controller does not provide transfer-complete interrupt when not busy */
 #define SDHCI_QUIRK_NO_BUSY_IRQ				(1<<14)
 /* Controller has unreliable card detection */
 #define SDHCI_QUIRK_BROKEN_CARD_DETECTION		(1<<15)
 /* Controller reports inverted write-protect state */
 #define SDHCI_QUIRK_INVERTED_WRITE_PROTECT		(1<<16)
 /* Controller has nonstandard clock management */
 #define SDHCI_QUIRK_NONSTANDARD_CLOCK			(1<<17)
 /* Controller does not like fast PIO transfers */
 #define SDHCI_QUIRK_PIO_NEEDS_DELAY			(1<<18)
 /* Controller losing signal/interrupt enable states after reset */
 #define SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET		(1<<19)
 /* Controller has to be forced to use block size of 2048 bytes */
 #define SDHCI_QUIRK_FORCE_BLK_SZ_2048			(1<<20)
 /* Controller cannot do multi-block transfers */
 #define SDHCI_QUIRK_NO_MULTIBLOCK			(1<<21)
 /* Controller can only handle 1-bit data transfers */
 #define SDHCI_QUIRK_FORCE_1_BIT_DATA			(1<<22)
 /* Controller needs 10ms delay between applying power and clock */
 #define SDHCI_QUIRK_DELAY_AFTER_POWER			(1<<23)
 /* Controller uses SDCLK instead of TMCLK for data timeouts */
 #define SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK		(1<<24)
 /* Controller reports wrong base clock capability */
 #define SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN		(1<<25)
 /* Controller cannot support End Attribute in NOP ADMA descriptor */
 #define SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC		(1<<26)
 /* Controller is missing device caps. Use caps provided by host */
 #define SDHCI_QUIRK_MISSING_CAPS			(1<<27)
 /* Controller uses Auto CMD12 command to stop the transfer */
 #define SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12		(1<<28)
 /* Controller doesn't have HISPD bit field in HI-SPEED SD card */
 #define SDHCI_QUIRK_NO_HISPD_BIT			(1<<29)
 /* Controller treats ADMA descriptors with length 0000h incorrectly */
 #define SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC		(1<<30)
 /* The read-only detection via SDHCI_PRESENT_STATE register is unstable */
 #define SDHCI_QUIRK_UNSTABLE_RO_DETECT			(1<<31)

 	unsigned int quirks2;	/* More deviations from spec. */

 #define SDHCI_QUIRK2_HOST_OFF_CARD_ON			(1<<0)
 #define SDHCI_QUIRK2_HOST_NO_CMD23			(1<<1)
 /* The system physically doesn't support 1.8v, even if the host does */
 #define SDHCI_QUIRK2_NO_1_8_V				(1<<2)

 	int irq;		/* Device IRQ */
 	void __iomem *ioaddr;	/* Mapped address */

 	const struct sdhci_ops *ops;	/* Low level hw interface */

 	struct regulator *vmmc;		/* Power regulator (vmmc) */
 	struct regulator *vqmmc;	/* Signaling regulator (vccq) */

 	/* Internal data */
 	struct mmc_host *mmc;	/* MMC structure */
 	u64 dma_mask;		/* custom DMA mask */

 #if defined(CONFIG_LEDS_CLASS) || defined(CONFIG_LEDS_CLASS_MODULE)
 	struct led_classdev led;	/* LED control */
 	char led_name[32];
 #endif

 	spinlock_t lock;	/* Mutex */

 	int flags;		/* Host attributes */
 #define SDHCI_USE_SDMA		(1<<0)	/* Host is SDMA capable */
 #define SDHCI_USE_ADMA		(1<<1)	/* Host is ADMA capable */
 #define SDHCI_REQ_USE_DMA	(1<<2)	/* Use DMA for this req. */
 #define SDHCI_DEVICE_DEAD	(1<<3)	/* Device unresponsive */
 #define SDHCI_SDR50_NEEDS_TUNING (1<<4)	/* SDR50 needs tuning */
 #define SDHCI_NEEDS_RETUNING	(1<<5)	/* Host needs retuning */
 #define SDHCI_AUTO_CMD12	(1<<6)	/* Auto CMD12 support */
 #define SDHCI_AUTO_CMD23	(1<<7)	/* Auto CMD23 support */
 #define SDHCI_PV_ENABLED	(1<<8)	/* Preset value enabled */
 #define SDHCI_SDIO_IRQ_ENABLED	(1<<9)	/* SDIO irq enabled */
 #define SDHCI_HS200_NEEDS_TUNING (1<<10)	/* HS200 needs tuning */
 #define SDHCI_USING_RETUNING_TIMER (1<<11)	/* Host is using a retuning timer for the card */

 	unsigned int version;	/* SDHCI spec. version */

 	unsigned int max_clk;	/* Max possible freq (MHz) */
 	unsigned int timeout_clk;	/* Timeout freq (KHz) */
 	unsigned int clk_mul;	/* Clock Muliplier value */

 	unsigned int clock;	/* Current clock (MHz) */
 	u8 pwr;			/* Current voltage */

 	bool runtime_suspended;	/* Host is runtime suspended */

 	struct mmc_request *mrq;	/* Current request */
 	struct mmc_command *cmd;	/* Current command */
 	struct mmc_data *data;	/* Current data request */
 	unsigned int data_early:1;	/* Data finished before cmd */

 	struct sg_mapping_iter sg_miter;	/* SG state for PIO */
 	unsigned int blocks;	/* remaining PIO blocks */

 	int sg_count;		/* Mapped sg entries */

 	u8 *adma_desc;		/* ADMA descriptor table */
 	u8 *align_buffer;	/* Bounce buffer */

 	dma_addr_t adma_addr;	/* Mapped ADMA descr. table */
 	dma_addr_t align_addr;	/* Mapped bounce buffer */

 	struct tasklet_struct card_tasklet;	/* Tasklet structures */
 	struct tasklet_struct finish_tasklet;

 	struct timer_list timer;	/* Timer for timeouts */

 	u32 caps;		/* Alternative CAPABILITY_0 */
 	u32 caps1;		/* Alternative CAPABILITY_1 */

 	unsigned int            ocr_avail_sdio;	/* OCR bit masks */
 	unsigned int            ocr_avail_sd;
 	unsigned int            ocr_avail_mmc;

 	wait_queue_head_t	buf_ready_int;	/* Waitqueue for Buffer Read Ready interrupt */
 	unsigned int		tuning_done;	/* Condition flag set when CMD19 succeeds */

 	unsigned int		tuning_count;	/* Timer count for re-tuning */
 	unsigned int		tuning_mode;	/* Re-tuning mode supported by host */
 #define SDHCI_TUNING_MODE_1	0
 	struct timer_list	tuning_timer;	/* Timer for tuning */

 	unsigned long private[0] ____cacheline_aligned;
 };
 #endif /* LINUX_MMC_SDHCI_H */
	/*
	* linux/include/linux/mmc/sdhci.h - Secure Digital Host Controller Interface
	*
	* Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
	*
	* This program is free software; you can redistribute it and/or modify
	* it under the terms of the GNU General Public License as published by
	* the Free Software Foundation; either version 2 of the License, or (at
	* your option) any later version.
	*/
	#ifndef LINUX_MMC_SDHCI_H
	#define LINUX_MMC_SDHCI_H

	#include <linux/scatterlist.h>
	#include <linux/compiler.h>
	#include <linux/types.h>
	#include <linux/io.h>
	#include <linux/mmc/host.h>

	struct sdhci_host {
	/* Data set by hardware interface driver */
	const char hw_name; / Hardware bus name */

	unsigned int quirks; /* Deviations from spec. */

	/* Controller doesn't honor resets unless we touch the clock register */
	#define SDHCI_QUIRK_CLOCK_BEFORE_RESET (1<<0)
	/* Controller has bad caps bits, but really supports DMA */
	#define SDHCI_QUIRK_FORCE_DMA (1<<1)
	/* Controller doesn't like to be reset when there is no card inserted. */
	#define SDHCI_QUIRK_NO_CARD_NO_RESET (1<<2)
	/* Controller doesn't like clearing the power reg before a change */
	#define SDHCI_QUIRK_SINGLE_POWER_WRITE (1<<3)
	/* Controller has flaky internal state so reset it on each ios change */
	#define SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS (1<<4)
	/* Controller has an unusable DMA engine */
	#define SDHCI_QUIRK_BROKEN_DMA (1<<5)
	/* Controller has an unusable ADMA engine */
	#define SDHCI_QUIRK_BROKEN_ADMA (1<<6)
	/* Controller can only DMA from 32-bit aligned addresses */
	#define SDHCI_QUIRK_32BIT_DMA_ADDR (1<<7)
	/* Controller can only DMA chunk sizes that are a multiple of 32 bits */
	#define SDHCI_QUIRK_32BIT_DMA_SIZE (1<<8)
	/* Controller can only ADMA chunks that are a multiple of 32 bits */
	#define SDHCI_QUIRK_32BIT_ADMA_SIZE (1<<9)
	/* Controller needs to be reset after each request to stay stable */
	#define SDHCI_QUIRK_RESET_AFTER_REQUEST (1<<10)
	/* Controller needs voltage and power writes to happen separately */
	#define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1<<11)
	/* Controller provides an incorrect timeout value for transfers */
	#define SDHCI_QUIRK_BROKEN_TIMEOUT_VAL (1<<12)
	/* Controller has an issue with buffer bits for small transfers */
	#define SDHCI_QUIRK_BROKEN_SMALL_PIO (1<<13)
	/* Controller does not provide transfer-complete interrupt when not busy */
	#define SDHCI_QUIRK_NO_BUSY_IRQ (1<<14)
	/* Controller has unreliable card detection */
	#define SDHCI_QUIRK_BROKEN_CARD_DETECTION (1<<15)
	/* Controller reports inverted write-protect state */
	#define SDHCI_QUIRK_INVERTED_WRITE_PROTECT (1<<16)
	/* Controller has nonstandard clock management */
	#define SDHCI_QUIRK_NONSTANDARD_CLOCK (1<<17)
	/* Controller does not like fast PIO transfers */
	#define SDHCI_QUIRK_PIO_NEEDS_DELAY (1<<18)
	/* Controller losing signal/interrupt enable states after reset */
	#define SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET (1<<19)
	/* Controller has to be forced to use block size of 2048 bytes */
	#define SDHCI_QUIRK_FORCE_BLK_SZ_2048 (1<<20)
	/* Controller cannot do multi-block transfers */
	#define SDHCI_QUIRK_NO_MULTIBLOCK (1<<21)
	/* Controller can only handle 1-bit data transfers */
	#define SDHCI_QUIRK_FORCE_1_BIT_DATA (1<<22)
	/* Controller needs 10ms delay between applying power and clock */
	#define SDHCI_QUIRK_DELAY_AFTER_POWER (1<<23)
	/* Controller uses SDCLK instead of TMCLK for data timeouts */
	#define SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK (1<<24)
	/* Controller reports wrong base clock capability */
	#define SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN (1<<25)
	/* Controller cannot support End Attribute in NOP ADMA descriptor */
	#define SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC (1<<26)
	/* Controller is missing device caps. Use caps provided by host */
	#define SDHCI_QUIRK_MISSING_CAPS (1<<27)
	/* Controller uses Auto CMD12 command to stop the transfer */
	#define SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 (1<<28)
	/* Controller doesn't have HISPD bit field in HI-SPEED SD card */
	#define SDHCI_QUIRK_NO_HISPD_BIT (1<<29)
	/* Controller treats ADMA descriptors with length 0000h incorrectly */
	#define SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC (1<<30)
	/* The read-only detection via SDHCI_PRESENT_STATE register is unstable */
	#define SDHCI_QUIRK_UNSTABLE_RO_DETECT (1<<31)

	unsigned int quirks2; /* More deviations from spec. */

	#define SDHCI_QUIRK2_HOST_OFF_CARD_ON (1<<0)
	#define SDHCI_QUIRK2_HOST_NO_CMD23 (1<<1)
	/* The system physically doesn't support 1.8v, even if the host does */
	#define SDHCI_QUIRK2_NO_1_8_V (1<<2)

	int irq; /* Device IRQ */
	void __iomem ioaddr; / Mapped address */

	const struct sdhci_ops ops; / Low level hw interface */

	struct regulator vmmc; / Power regulator (vmmc) */
	struct regulator vqmmc; / Signaling regulator (vccq) */

	/* Internal data */
	struct mmc_host mmc; / MMC structure */
	u64 dma_mask; /* custom DMA mask */

	#if defined(CONFIG_LEDS_CLASS) \|\| defined(CONFIG_LEDS_CLASS_MODULE)
	struct led_classdev led; /* LED control */
	char led_name[32];
	#endif

	spinlock_t lock; /* Mutex */

	int flags; /* Host attributes */
	#define SDHCI_USE_SDMA (1<<0) /* Host is SDMA capable */
	#define SDHCI_USE_ADMA (1<<1) /* Host is ADMA capable */
	#define SDHCI_REQ_USE_DMA (1<<2) /* Use DMA for this req. */
	#define SDHCI_DEVICE_DEAD (1<<3) /* Device unresponsive */
	#define SDHCI_SDR50_NEEDS_TUNING (1<<4) /* SDR50 needs tuning */
	#define SDHCI_NEEDS_RETUNING (1<<5) /* Host needs retuning */
	#define SDHCI_AUTO_CMD12 (1<<6) /* Auto CMD12 support */
	#define SDHCI_AUTO_CMD23 (1<<7) /* Auto CMD23 support */
	#define SDHCI_PV_ENABLED (1<<8) /* Preset value enabled */
	#define SDHCI_SDIO_IRQ_ENABLED (1<<9) /* SDIO irq enabled */
	#define SDHCI_HS200_NEEDS_TUNING (1<<10) /* HS200 needs tuning */
	#define SDHCI_USING_RETUNING_TIMER (1<<11) /* Host is using a retuning timer for the card */

	unsigned int version; /* SDHCI spec. version */

	unsigned int max_clk; /* Max possible freq (MHz) */
	unsigned int timeout_clk; /* Timeout freq (KHz) */
	unsigned int clk_mul; /* Clock Muliplier value */

	unsigned int clock; /* Current clock (MHz) */
	u8 pwr; /* Current voltage */

	bool runtime_suspended; /* Host is runtime suspended */

	struct mmc_request mrq; / Current request */
	struct mmc_command cmd; / Current command */
	struct mmc_data data; / Current data request */
	unsigned int data_early:1; /* Data finished before cmd */

	struct sg_mapping_iter sg_miter; /* SG state for PIO */
	unsigned int blocks; /* remaining PIO blocks */

	int sg_count; /* Mapped sg entries */

	u8 adma_desc; / ADMA descriptor table */
	u8 align_buffer; / Bounce buffer */

	dma_addr_t adma_addr; /* Mapped ADMA descr. table */
	dma_addr_t align_addr; /* Mapped bounce buffer */

	struct tasklet_struct card_tasklet; /* Tasklet structures */
	struct tasklet_struct finish_tasklet;

	struct timer_list timer; /* Timer for timeouts */

	u32 caps; /* Alternative CAPABILITY_0 */
	u32 caps1; /* Alternative CAPABILITY_1 */

	unsigned int ocr_avail_sdio; /* OCR bit masks */
	unsigned int ocr_avail_sd;
	unsigned int ocr_avail_mmc;

	wait_queue_head_t buf_ready_int; /* Waitqueue for Buffer Read Ready interrupt */
	unsigned int tuning_done; /* Condition flag set when CMD19 succeeds */

	unsigned int tuning_count; /* Timer count for re-tuning */
	unsigned int tuning_mode; /* Re-tuning mode supported by host */
	#define SDHCI_TUNING_MODE_1 0
	struct timer_list tuning_timer; /* Timer for tuning */

	unsigned long private[0] ____cacheline_aligned;
	};
	#endif /* LINUX_MMC_SDHCI_H */